aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
* ramips: update i2c driversMichael Lee2016-06-202-371/+611
| | | | | | | | | | | | | | | | | * add rt_i2c structure to store driver data * rewrite read/write check function and add i2c error status check. so we don't need to wait until time out. * add 10 bits address support. according to the data sheet i think it is possible. but i haven't verify it. * the most important is start transfer only need once. otherwise it cause I2C_STARTERR status. * add set i2c clock speed register by dts options "clock-frequency". not just hard code it. * add mt7621 i2c driver. i just copy i2c-ralink.c and change register names. and the hardware don't support error status. so i remove it. but the logic is the same. Signed-off-by: Michael Lee <igvtee@gmail.com>
* ipq806x: fix MAC_POWER_SEL switch configurationJosh Bendavid2016-06-205-6/+6
| | | | | | Fixes instability/corruption on the ethernet interface connected to port0 on the switch. Signed-off-by: Josh Bendavid <joshbendavid@gmail.com>
* lantiq: BTHOMEHUBV5A - use the power event code for the restart buttonMathias Kresin2016-06-201-1/+1
| | | | | | | | | | The restart event code is used in LEDE to trigger a factory reset on long press as well. By using the power event code, the restart functionality can be used without being prone to trigger a factory reset. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: diag - switch off the power led on failsafeMathias Kresin2016-06-201-0/+4
| | | | | | | | | | | | | | This patch is a follow up to commit 4cf3fd4 "add support for indicating the boot state using three leds". At the time of writing the patch, I wasn't aware that it's possible to switch info failsafe after boot (factory reset). Enabling the failsafe led without disabling the running led causes an unexpected led colour on devices using a single multicolour led to indicate the boot state. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: fix build of NAND sysupgrade imagesMathias Kresin2016-06-201-57/+45
| | | | | | | | | | | | | The *_UBIFS_OPTS variables need to be prefixed with DEVICE_ to match the profile name. The conditions need to be evaluated after the *_UBIFS_OPTS are set, otherwise the variables are always empty. Do not append or pass the DEVICE_ prefixed profile name to the images. Use the name that is passed by the Image/Build/Profile/ step. Signed-off-by: Mathias Kresin <dev@kresin.me>
* bcm53xx: properly support sysupgrade using Seama on NAND devicesRafał Miłecki2016-06-201-1/+48
| | | | | | It updates kernel and then formats UBI without loosing erase counters. Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
* kernel: rename B53 symbols to avoid upstream kernel conflictRafał Miłecki2016-06-2013-52/+52
| | | | | | | | | In kernel 4.7 there is upstreamed b53 driver using (mostly?) the same symbols as our b53 does. Change our symbols so both drivers can coexist in kernel tree. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Acked-by: Jonas Gorski <jonas.gorski@gmail.com>
* kernel: mtdsplit: calculate kernel partition precisely for SeamaRafał Miłecki2016-06-201-2/+2
| | | | | | | | | So far "kernel" partition didn't contain just a kernel. It also included Seama header and meta data. This was making kernel update complex and it wasn't trivial to read kernel size. Fix it by making "kernel" parition contain just a kernel image. Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
* kernel: backport cosmetic ubifs patchDaniel Golle2016-06-181-0/+42
| | | | | | | | | | | | | | | Despite the MS_SILENT flag being set when probing for ubifs rootfs a logline indicating an error is generated during boot: UBIFS error (pid: 1): cannot open "ubi0:rootfs", error -19 This leads to confusion and there shouldn't be lines containing the word 'error' twice in a bootlog if actually everything is fine (just the rootfs happens to be something else than ubifs) The patch added has been submitted and was accepted upstream, see: http://lists.infradead.org/pipermail/linux-mtd/2016-June/068056.html http://patchwork.ozlabs.org/patch/637491 Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* lantiq: clean up / fix LegacyDevice template handlingFelix Fietkau2016-06-171-15/+7
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* lantiq: get rid of ifneq() checks inside command templatesFelix Fietkau2016-06-171-34/+34
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* lantiq: small fix for legacy profile buildsJohn Crispin2016-06-171-36/+7
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* octeon: fix image buildJo-Philipp Wich2016-06-171-1/+1
| | | | | | | | | | | The generic sysupgrade image attempted to use the wrong filesystem type due to premature variable interpolation leading to the following error on the buildbot system: cp: cannot stat `.../root.squashfs': No such file or directory make[4]: *** [.../tmp/lede-octeon-generic-ext4-sysupgrade.tar] Error 1 Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* medaitek: convert the NAND target to UBIJohn Crispin2016-06-177-192/+62
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* ar71xx: WDR4300: Fixed default VLAN orderDavid Pinilla Caparrós2016-06-171-1/+1
| | | | | | Reordered the VLANs so the LAN ports are set to VLAN 1 and the WAN port is set to VLAN 2, as in the other routers in the config file. Moreover, this model had this VLAN mapping in OpenWRT Chaos Calmer. It seems that the VLAN were switched when fixing a bug in the port mapping ( OpenWRT changeset 47799 ) Signed-off-by: David Pinilla Caparrós <dpinitux@gmail.com>
* Revert "ramips: update i2c drivers"John Crispin2016-06-172-611/+371
| | | | | | | | This reverts commit d8202a84096831d4e6e2a522476bd6a0d46e6413. the commit broke I2C on various boards. Signed-off-by: John Crispin <john@phrozen.org>
* ipq806x: activate ATAG DTB mangle and EA8500 rootblock in dtsAdrian Panella2016-06-173-1/+190
| | | | | | | | | | | | | | The command-line arguments provided by the boot loader will be appended to a new device tree property: bootloader-args. If there is a property "append-rootblock" in DT under /chosen and a root= option in bootloaders command line it will be parsed and added to DT bootargs with the form: <append-rootblock>XX. Only command line ATAG will be processed, the rest of the ATAGs sent by bootloader will be ignored. This is usefull in dual boot systems, to get the current root partition without afecting the rest of the system. Signed-off-by: Adrian Panella <ianchi74@outlook.com>
* cns3xxx: fix RX softIRQ loopKoen Vandeputte2016-06-171-2/+2
| | | | | | | | | | Already reschedule when 1 or more frames came in. Checking for a full queue could produce a re-schedule loop as the checked RX ring location could contain undefined values depending on activity in previous loops. Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* netlogic: R.I.PJohn Crispin2016-06-1710-370/+0
| | | | | | | I asked florian and he is ok with this. i think no one apart from him has access to these boards. Signed-off-by: John Crispin <john@phrozen.org>
* lantiq: convert remaining legacy targets to the new image generation codeJohn Crispin2016-06-178-98/+101
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* Revert "ar71xx/cpe510: use second wifi calibration table"Alexander Couzens2016-06-161-1/+1
| | | | | | | | Using the high power table can damage the device in some cases. This reverts commit bf27ac019c137e7baf90ca6ef0e40945ae871797. Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* Revert "lantiq: Use correct macaddr generating logic for the DGN3500"Felix Fietkau2016-06-151-5/+0
| | | | | | | This reverts commit 492964e741f1e0254b6ed7c0a095551a31d25dc9, which makes no sense. /etc/board.d cannot be used for system init stuff. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* realview: sync kernel config fileJohn Crispin2016-06-151-13/+29
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* lantiq: refresh patchesFelix Fietkau2016-06-156-100/+89
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: refresh patchesFelix Fietkau2016-06-154-28/+24
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: replace SMP cacheflush fix with some patches from linux-mti.gitFelix Fietkau2016-06-153-17/+354
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* bcm53xx: use uncompressed zImagesFelix Fietkau2016-06-151-0/+2
| | | | | | The boot loader expects LZMA compressed kernel images Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: add support for uncompressed zImage on ARMFelix Fietkau2016-06-154-2/+137
| | | | | | | This can be used to prevent double compression for platforms where the boot loader already expects compressed images. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: add common config symbolsFelix Fietkau2016-06-151-0/+6
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* bcm53xx: refresh kernel configFelix Fietkau2016-06-151-5/+0
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ipq806x: add missing kernel config symbolJo-Philipp Wich2016-06-151-0/+1
| | | | Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* mvebu: Configure status LED for WRT1900ACSRujun Wang2016-06-151-0/+3
| | | | Signed-off-by: Rujun Wang <chinawrj@gmail.com>
* realview: bump to v4.4John Crispin2016-06-152-1/+1
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* octeon: export the FILESYSTEMS variable during image generationJohn Crispin2016-06-151-1/+1
| | | | | | squashfs will be used for all images if this is not done Signed-off-by: John Crispin <john@phrozen.org>
* octeon: Ignore MEM boot param when too smallJohn Crispin2016-06-141-0/+31
| | | | | | | | Cisco RV0XX u-boot sets MEM=2048 as boot param. We assume that at least 4MB (mem_alloc_size) of ram is needed to run linux on cavium boards, so if mem < 4M - ignore it and set default value Signed-off-by: Michał Osowiecki <michal.osowiecki@gmail.com>
* ipq806x: restore old stmmac dma patch which is still needed to fix data ↵Josh Bendavid2016-06-141-0/+117
| | | | | | corruption Signed-off-by: Josh Bendavid <joshbendavid@gmail.com>
* Revert "ipq806x: add mangle bootargs options in config-4.4"Josh Bendavid2016-06-141-4/+1
| | | | | | | | This reverts commit 53147c2237231842b4d185f69c2bc0d79aff8b85. These config changes break booting on C2600 and probably other devices. Signed-off-by: Josh Bendavid <joshbendavid@gmail.com>
* octeon: convert to new image building codeJohn Crispin2016-06-142-50/+41
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* mediatek/ralink: fix boardnamesJohn Crispin2016-06-142-2/+2
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* omap: remove NAMESPACES config symbolsDirk Neukirchen2016-06-141-3/+0
| | | | | | they are available in config/Config-kernel.in Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
* omap: remove XFRM config symbolsDirk Neukirchen2016-06-141-2/+0
| | | | Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
* omap: remove config symbol W1Dirk Neukirchen2016-06-141-1/+0
| | | | | | it is available as module Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
* omap: remove config symbol NETFILTERDirk Neukirchen2016-06-141-1/+0
| | | | Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
* omap: remove BMP085 symbolDirk Neukirchen2016-06-141-2/+0
| | | | | | BMP085 is a pressure sensor and available as module Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
* lantiq: the io space was still not big enough for UHCIJohn Crispin2016-06-141-1/+1
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* lantiq: add ARV4525PW wifi ledJohn Crispin2016-06-141-0/+3
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* lantiq: fix VG3503J loader generationJohn Crispin2016-06-141-1/+1
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* lantiq: fix fritz7320 wifi supportJohn Crispin2016-06-144-6/+27
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* lantiq: fix io_space_limitJohn Crispin2016-06-141-0/+28
| | | | | | this broke uhci pci support on some arv units Signed-off-by: John Crispin <john@phrozen.org>
* ramips: fix kmod-sound-mt7620 packagingJo-Philipp Wich2016-06-141-6/+5
| | | | | | | | | | | | | Commit 9ff8928bb9c28be701eb963e591afcfd54b9d8c9 renamed the snd-soc-mt7620-i2s driver and dropped snd-soc-mt7620-wm8960 which selected CONFIG_SND_SOC_WM8960 breaking all ramips builds due to undefined kernel config symbols. Rework the kmod-sound-mt7620 package to explicitely select the CONFIG_SND_SOC_WM8960 symbols and change it to bundle the renamed .ko file. Also remove the @BROKEN flag and exclude it on the rt288x subtarget instead. Signed-off-by: Jo-Philipp Wich <jo@mein.io>