aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
* kernel: add support for GD25D05 SPI NORKoen Vandeputte2020-02-043-0/+87
| | | | | | | | | | | | | | | | | | | | | | This chip is used on newer RB912UAG-5HPnD r2 boards: Before: [ 0.642553] m25p80 spi0.0: unrecognized JEDEC id bytes: c8, 40, 10 [ 0.649381] NAND flash driver for the RouterBOARD 91x series After: [ 0.641714] m25p80 spi0.0: found gd25d05, expected m25p80 [ 0.649916] m25p80 spi0.0: gd25d05 (64 Kbytes) [ 0.655122] Creating 4 MTD partitions on "spi0.0": [ 0.660164] 0x000000000000-0x00000000c000 : "routerboot" [ 0.667782] 0x00000000c000-0x00000000d000 : "hard_config" [ 0.675073] 0x00000000d000-0x00000000e000 : "bios" [ 0.682613] 0x00000000e000-0x00000000f000 : "soft_config" [ 0.690304] NAND flash driver for the RouterBOARD 91x series Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.19 to 4.19.101Koen Vandeputte2020-02-0439-406/+86
| | | | | | | | | | | | | | | | | | Refreshed all patches. Fixes: - CVE-2019-14896 - CVE-2019-14897 Remove upstreamed: - 023-0007-crypto-crypto4xx-Fix-wrong-ppc4xx_trng_probe-ppc4xx_.patch - 950-0202-staging-bcm2835-camera-fix-module-autoloading.patch - 001-4.22-01-MIPS-BCM63XX-drop-unused-and-broken-DSP-platform-dev.patch Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.169Koen Vandeputte2020-02-0426-325/+78
| | | | | | | | | | | | | | | | | Refreshed all patches. Fixes: - CVE-2019-14896 - CVE-2019-14897 Remove upstreamed: - 023-0007-crypto-crypto4xx-Fix-wrong-ppc4xx_trng_probe-ppc4xx_.patch - 001-4.22-01-MIPS-BCM63XX-drop-unused-and-broken-DSP-platform-dev.patch Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ramips: remove unnecessary execute permission bitSungbo Eo2020-02-041-0/+0
| | | | | | | | dts file does not need to be executable. 644 is enough. Fixes: f098c612b6db ("ramips: create shared DTSI for Netgear EX2700 and WN3000RP v3") Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* mediatek: remove unnecessary execute permission bitSungbo Eo2020-02-043-0/+0
| | | | | | | | kernel config and patch files do not need to be executable. 644 is enough. Fixes: 01c8f2e97cc6 ("mediatek: bump to v4.19") Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ath79: WNDR3700 v1/v2: make u-boot env partition writableMichal Cieslakiewicz2020-02-042-2/+0
| | | | | | | Remove read-only flag from U-boot environment partition for Netgear WNDR3700 v1 and v2 so u-boot-envtools can modify data there. Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* mediatek: remove KERNEL_PATCHVER overwrite for mt7629Adrian Schmutzler2020-02-041-1/+0
| | | | | | | | Since whole target has been bumped to kernel 4.19 in 01c8f2e97cc6 ("mediatek: bump to v4.19") we do not need the overwrite in mt7629 subtarget anymore. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mediatek: bump to v4.19John Crispin2020-02-044-1/+562
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* ath79: add support for COMFAST CF-E560ACAugust Huber2020-02-035-6/+205
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the COMFAST CF-E560AC, an ap143 based in-wall access point. Specifications: - SoC: Qualcomm Atheros QCA9531 - RAM: 128 MB DDR2 (Winbond W971GG6SB-25) - Storage: 16 MB NOR (Winbond 25Q128JVSO) - WAN: 1x 10/100 PoE ethernet (48v) - LAN: 4x 10/100 ethernet - WLAN1: QCA9531 - 802.11b/g/n - 2x SKY85303-21 FEM - WLAN2: QCA9886 - 802.11ac/n/a - 2x SKY85735-11 FEM - USB: one external USB2.0 port - UART: 3.3v, 2.54mm headers already populated on board - LED: 7x external - Button: 1x external - Boot: U-Boot 1.1.4 (pepe2k/u-boot_mod) MAC addressing: - stock LAN *:40 (label) WAN *:41 5G *:42 2.4G *:4a - flash (art partition) 0x0 *:40 (label) 0x6 *:42 0x1002 *:41 0x5006 *:43 This device contains valid MAC addresses in art 0x0, 0x6, 0x1002 and 0x5006, however the vendor firmware only reads from art:0x0 for the LAN interface and then increments in 02_network. They also jump 8 addresses for the second wifi interface (2.4 GHz). This behavior has been duplicated in the DTS and ath10k hotplug to align addresses with the vendor firmware v2.6.0. Recovery instructions: This device contains built-in u-boot tftp recovery. 1. Configure PC with static IP 192.168.1.10/24 and tftp server. 2. Place desired image at /firmware_auto.bin at tftp root. 3. Connect device to PC, and power on. 4. Device will fetch flash from tftp, flash and reboot into new image. Signed-off-by: August Huber <auh@google.com> [move jtag_disable_pins, remove unnecessary statuses in DTS, remove duplicate entry in 11-ath10k-caldata, remove hub_port0 label in DTS] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: WNDR3700 v2: add dash before version in device nameMichal Cieslakiewicz2020-02-034-9/+9
| | | | | | | | Adapt Netgear WNDR3700v2 device identification string to ath79 naming scheme by changing from 'wndr3700v2' to 'wndr3700-v2' (affects config, makefile, init scripts and device tree definition). Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* mediatek: add wmac devicetree node for MT7622John Crispin2020-02-021-0/+11
| | | | | Signed-off-by: John Crispin <john@phrozen.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ath79: add common definition for Device/tplink-v2Adrian Schmutzler2020-02-022-8/+13
| | | | | | | | | | | | | | | | This adds a shared definition Device/tplink-v2 to common-tp-link.mk. Though currently only one device in ath79 uses it, putting it in the common file seems more organized. The definitions are based on the implementation in ramips target, where a lot of devices is using tplink-v2-* commands already. The '-V "ver. 2.0"' suffix for Archer D50 v1 can be removed because it's default in Build/tplink-v2-image anyway. While at it, add TPLINK_HWREVADD and TPLINK_HVERSION to DEVICE_VARS, which seems to have been overlooked when adding Archer D50 v1. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: rename tplink-loader-okli to tplink-safeloader-okliAdrian Schmutzler2020-02-022-10/+10
| | | | | | | | | This renames Device/tplink-loader-okli to Device/tplink-safeloader-okli since the latter more accurately describes the combination of tplink-safeloader and loader-okli use there. The old version might be confused with other uses of the okli loader. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: rename Device/tplink to Device/tplink-v1Adrian Schmutzler2020-02-021-6/+6
| | | | | | | | | As we have tplink-v2-header and tplink-v2-image recipes as well, this patch renames the Device/tplink definition to Device/tplink-v1, as it's using the tplink-v1-* commands. This should provide easier distinction in the future. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mvebu: image: align subtargets makefile namesTomasz Maciej Nowak2020-02-014-3/+3
| | | | | | | Align subtargets makefiles names to actual subtargets. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mvebu: image: sort devices alphabeticallyTomasz Maciej Nowak2020-02-012-114/+114
| | | | | | | | This sorts the devices in image Makefiles alphabetically. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> [fixed sorting in one case, add commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for TP-Link RE200 v2Andreas Böhler2020-02-015-0/+180
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link RE200 v2 is a wireless range extender with Ethernet and 2.4G and 5G WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN. Specifications -------------- - MediaTek MT7628AN (580 Mhz) - 64 MB of RAM - 8 MB of FLASH - 2T2R 2.4 GHz and 1T1R 5 GHz - 1x 10/100 Mbps Ethernet - UART header on PCB (57600 8n1) - 8x LED (GPIO-controlled), 2x button There are 2.4G and 5G LEDs in red and green which are controlled separately. MAC addresses ------------- The MAC address assignment matches stock firmware, i.e.: LAN : *:0D 2.4G: *:0E 5G : *:0F Installation ------------ Web Interface ------------- It is possible to upgrade to OpenWrt via the web interface. Simply flash the -factory.bin from OEM. In contrast to a stock firmware, this will not overwrite U-Boot. Serial console -------------- Opening the case is quite hard, since it is welded together. Rename the OpenWrt factory image to "test.bin", then plug in the device and quickly press "2" to enter flash mode (no line feed). Follow the prompts until OpenWrt is installed. Unfortunately, this devices does not offer a recovery mode or a tftp installation method. If the web interface upgrade fails, you have to open your device and attach serial console. Additonal notes --------------- It is possible to flash back to stock by using tplink-safeloader to create a sysupgrade image based on a stock update. After the first boot, it is necessary upgrade to another stock image, otherwise subsequent boots fail with LZMA ERROR 1 and you have to attach serial to recover the device. Signed-off-by: Andreas Böhler <dev@aboehler.at> [remove DEVICE_VARS change] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: collect and harmonize TP-Link image variants in common fileAdrian Schmutzler2020-02-014-114/+100
| | | | | | | | | | | | This moves the various variants of common device definitions for TP-Link devices to a common Makefile common-tp-link.mk. This provides the opportunity to reorganize and move parameters between individual device definitions and the common ones. While at it, also use the common definitions for previously independent definitions where appropriate. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: connmark set-dscpmark follow upstreamimg attemptKevin Darbyshire-Bryant2020-01-313-159/+265
| | | | | | | | | | | | | | I'm having another attempt at trying to getting the 'store dscp into conntrack connmark' functionality into upstream kernel, since the restore function (act_ctinfo) has been accepted. The syntax has changed from 'savedscp' to 'set-dscpmark' since that conforms more closely with existing functionality. 4.14 backport is more of a hack since the structure versioning mechanism isn't in place. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* ath79: add support for Ubiquiti NanoStation Loco M (XW)Roger Pueyo Centelles2020-01-314-0/+39
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the NanoStation Loco M2/M5 XW devices on the ath79 target (support was long ago available on ar71xx). Specifications: - AR9342 SoC @ 535 MHz - 64 MB RAM - 8 MB SPI flash - 1x 10/100 Mbps Ethernet, 24 Vdc PoE-in - AR8032 switch - 2T2R 5 GHz radio, 22 dBm - 13 dBi built-in antenna - POWER/LAN green LEDs - 4x RSSI LEDs (red, orange, green, green) - UART (115200 8N1) on PCB Flashing via TFTP: - Use a pointy tool (e.g., pen cap, paper clip) and keep the reset button on the device or on the PoE supply pressed - Power on the device via PoE (keep reset button pressed) - Keep pressing until LEDs flash alternatively LED1+LED3 => LED2+LED4 => LED1+LED3, etc. - Release reset button - The device starts a TFTP server at 192.168.1.20 - Set a static IP on the computer (e.g., 192.168.1.21/24) - Upload via tftp the factory image: $ tftp 192.168.1.20 tftp> bin tftp> trace tftp> put openwrt-ath79-generic-xxxxx-ubnt_nanostation-loco-m-xw-squashfs-factory.bin Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ath79: do not set inherited phy-mode/status properties againAdrian Schmutzler2020-01-3114-22/+2
| | | | | | | | | There are several cases where phy-mode and status properties are set again in DTS(I) files although those were set to the same values in parent DTSI files already. Remove those cases (and thus also stop their proliferation by copy/paste). Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: harmonize ethernet-phy naming schemeAdrian Schmutzler2020-01-316-15/+25
| | | | | | | | | | | A minority of ethernet-phy definitions seems to use numbers in label, name and reg property relatively random. This patch aligns their use to have the same numeric value for all of them. While at it, improve order of properties/add newlines for the ethX nodes where necessary. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mediatek: mt7623: remove left-over fragments of mt7623a-rfb-emmcAdrian Schmutzler2020-01-303-468/+2
| | | | | | | | | | | | | | The image creation for the mt7623a-rfb-emmc has been removed during a patch refresh without specific comment. The corresponding base-files entries and DTS patches for 4.14 are still there. Since mt7623 is pretty dead and nobody has missed this device, let's just remove the rest. Fixes: 050da2107a7e ("mediatek: backport upstream mediatek patches") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Acked-by: John Crispin <john@phrozen.org>
* ramips: use tpt DTS trigger for TP-Link TL-MR3020 v3 and TL-WA801ND v5Jan Alexander2020-01-303-7/+5
| | | | | | | | | | | | | | This converts the TP-Link TL-MR3020v3 board to use the WLAN throughput LED trigger in order to react to all VAPs. It also moves the WLAN trigger config of the TP-Link TL-WA801NDv5 to the DTS and merges the now identical LAN LED configs. Verified these changes on a TL-MR3020v3. Signed-off-by: Jan Alexander <jan@nalx.net> [changed commit title and extended commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* Revert "ramips: fix NETGEAR R6260 EEPROM offset"David Bauer2020-01-304-26/+4
| | | | | | | | | | | | | This reverts commit 4716c843d62a5a4c37e7886f54bcf446aa26e786. Netgear seems to use different partition layouts on the R6260, which would require us to dynamically detect the position of (at least) the factory partition. Revert this fix to avoid breaking existing installations until a better solution has been worked out. Signed-off-by: David Bauer <mail@david-bauer.net>
* kernel: add support for XTX xt25f128 SPI-NOR flash chipsDaniel Golle2020-01-302-0/+86
| | | | | | | This fixes support for Teltonika RUT9xx which in recent versions of the device uses xt25f128b flash. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: remove duplicate DEVICE_PACKAGES for TP-Link Archer C20iAdrian Schmutzler2020-01-291-1/+0
| | | | | | | | | DEVICE_PACKAGES is specified twice for the same device. Remove the first (=older) assignment. Fixes: 40692f0fb55c ("ramips: mt7620: select only the matching mt76 driver") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for GL.iNet 6408/6416 (GL.iNet V1)Adrian Schmutzler2020-01-295-0/+211
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This ports the GL.iNet 6408/6416 from ar71xx. The GL-Connect GL.iNet v1 routers are basically a TP-Link TL-WR710N with more DRAM/Flash and console/GPIO header in the same small form-factor. Specifications: - SoC: Atheros AR9331 - CPU: 400 MHz - Flash: 8/16 MiB - RAM: 64 MiB - WiFi: 2.4 GHz b/g/n (SoC) - Ethernet: 2x 100M ports (LAN/WAN) - USB: 1x 2.0 The difference between 6408 and 6416 is just the flash size. It looks like only the 16 MiB version has been advertised, while the 6408 is a modified version. There are also 1-port versions sold by third parties. Installation: Install the sysupgrade image via stock firmware GUI or upload it via uboot (web-based). The device will be available at 192.168.1.1. Attention: In ar71xx, the same board name is used for both flash versions. So, please make sure you flash the correct ath79 image when upgrading. This has been device-tested on a GL.iNet 6416. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: fix NETGEAR R6260 EEPROM offsetDavid Bauer2020-01-294-4/+26
| | | | | | | | | | The EEPROM offset for the NETGEAR R6260 is incorrect, thus no valid calibration data is used. Fix this only for the NETGEAR R6260, as it's currently unknown whether or not other boards are affected. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for GL.iNet microuter-N300David Bauer2020-01-295-91/+142
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The GL.iNet microuter-N300 (internally referred as MT300N-v4) is a pocket-size travel router. It is essentially identical to the VIXMINI (internally referred as MT300N-v3) but with double the RAM and SPI-flash. Additionally, set the label-mac for both the VIXMINI as well as the microuter-N300. Hardware -------- SoC: MediaTek MT7628NN RAM: 128M DDR2 FLASH: 16M LED: Power - WLAN BTN: Reset UART: 115200 8N1 TX and RX are labled on the board as pads next to the SoC Installation via web-interface ------------------------------ 1. Visit the web-interface at 192.168.8.1 Note: The ethernet port is by default WAN. So you need to connect to the router via WiFi 2. Navigate to the Update tab on the left side. 3. Select "Local Update" 4. Upload the OpenWrt sysupgrade image. Note: Make sure you select not to preserve the configuration. Installation via U-Boot ----------------------- 1. Hold down the reset button while powering on the device. Wait for the LED to flash 5 times. 2. Assign yourself a static IPv4 in 192.168.1.0/24 3. Upload the OpenWrt sysupgrade image at 192.168.1.1. Signed-off-by: David Bauer <mail@david-bauer.net>
* octeon: apply vendor_model scheme to device definition/image nameAdrian Schmutzler2020-01-261-11/+13
| | | | | | | | | | | | | | | This updates the device definition name for octeon target to provide more useful names for the images and be consistent with the increasing number of targets following that scheme. Since the target is not using device tree yet, this does not touch board_name and thus sets BOARD_NAME in image Makefile to ensure sysupgrade is still working. While at it, move Build block before Device blocks and remove trailing whitespace for CMDLINE. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mediatek: use consistent naming scheme for device nodesAdrian Schmutzler2020-01-265-23/+22
| | | | | | | | | | | | | | | | | | | | | This harmonizes the device node names (and thus the image names, too) between subtargets of the mediatek target. So far, each subtarget has somewhat used its own naming scheme. Now, we use the vendor_device syntax there, too. Since DTS names have different patterns and the target only contains a few devices, this does not replace DEVICE_DTS by a calculated default value (like for other targets). SUPPORTED_DEVICES is adjusted based on the node rename where necessary, though it looks like for several older devices it was not set up correctly so far. While at it, this also changes the DTS name for u7623-02-emmc-512m to all-lower-case. Cc: John Crispin <john@phrozen.org> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mvebu: remove bashismSven Roederer2020-01-261-1/+1
| | | | | | | | | "[[" is a bash extension for test. As the ash-implementation is not fully compatible we drop its usage. Signed-off-by: Sven Roederer <devel-sven@geroedel.de> [split patch, remove shebang, adjust commit title/message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: sfp: add Nokia SFP fix from net-nextScott Roberts2020-01-2612-37/+145
| | | | | | Add Nokia GPON ONT SFP fix for tx_fault in net-next. Signed-off-by: Scott Roberts <ttocsr@gmail.com>
* ipq40xx: fix misplaced cells-sizes in WPJ419's dtsChristian Lamparter2020-01-261-2/+2
| | | | | | | | | | This patch fixes the occurences of the following warning message from the dtc: Warning (reg_format): /soc/spi@78b5000/flash0@0/partitions/partition@0:reg: property has invalid length (8 bytes) (#address-cells == 2, #size-cells == 1) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for EnGenius EMD1Yen-Ting-Shen2020-01-265-1/+261
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB NOR: 32 MiB ETH: Qualcomm Atheros QCA8072 (1 port) WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: RESET Button LEDS: White, Blue, Red, Orange Flash instruction: From EnGenius firmware to OpenWrt firmware: In Firmware Upgrade page, upgrade your openwrt-ipq40xx-generic-engenius_emd1-squashfs-factory.bin directly. From OpenWrt firmware to EnGenius firmware: 1. Setup a TFTP server on your computer and configure static IP to 192.168.99.8 Put the EnGenius firmware in the TFTP server directory on your computer. 2. Power up EMD1. Press 4 and then press any key to enter u-boot. 3. Download EnGenius firmware (IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-emd1-nor-fw-s.img 4. Flash the firmware (IPQ40xx) # imgaddr=0x84000000 && source 0x84000000:script 5. Reboot (IPQ40xx) # reset Signed-off-by: Yen-Ting-Shen <frank.shen@senao.com> [removed BOARD_NAME] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: Add support for D-Link DAP-2610Fredrik Olofsson2020-01-266-2/+295
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications ============== - SOC: IPQ4018 - RAM: DDR3 256MB - Flash: SPI NOR 16MB - WiFi: - 2.4GHz: IPQ4018, 2x2, front end SKY85303-11 - 5GHz: IPQ4018, 2x2, front end SKY85717-21 - Ethernet: 1x 10/100/1000Mbps, POE 802.3af - PHY: QCA8072 - UART: GND, blocked, 3.3V, RX, TX / 115200 8N1 - LED: 1x red / green - Button: 1x reset / factory default - U-Boot bootloader with tftp and "emergency web server" accessible using serial port. Installation ============ Flash factory image from D-Link web UI. Constraints in the D-Link web UI makes the factory image unnecessarily large. Flash again using sysupgrade from inside OpenWrt to reclaim some flash space. Return to stock D-Link firmware =============================== Partition layout is preserved, and it is possible to return to the stock firmware simply by downloading it from D-Link and writing it to the firmware partition. # mtd -r write dap2610-firmware.bin firmware Quirks ====== To be flashable from the D-Link http server, the firmware must be larger then 6MB, and the size in the firmware header must match the actual file size. Also, the boot loader verifies the checksum of the firmware before each boot, thus the jffs2 must be after the checksum covered part. This is solved in the factory image by having the rootfs at the very end of the image (without pad-rootfs). The sysupgrade image which does not have to be flashable from the D-Link web UI may be smaller, and the checksum in the firmware header only covers the kernel part of the image. Signed-off-by: Fredrik Olofsson <fredrik.olofsson@anyfinetworks.com> [added WRGG Variables to DEVICE_VARS, squashed spi pinconf/mux, added emd1's gmac0 config,fix dtc warnings] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* lantiq: tidy up image/MakefileAdrian Schmutzler2020-01-241-7/+5
| | | | | | | This harmonizes indent for Build blocks and removes multiple empty lines. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* lantiq: fix setting SOC to DEFAULT_SOCAdrian Schmutzler2020-01-241-0/+1
| | | | | | | | | This adds the missing assignment of DEFAULT_SOC to the SOC variable by default. Fixes: 09ee51c614d9 ("lantiq: define SOC only once for uniform targets") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* lantiq: define SOC only once for uniform targetsAdrian Schmutzler2020-01-246-38/+4
| | | | | | | | | | | | | | In lantiq there are several subtarget where all devices have the same value set to the SOC variable for each device individually. This patch introduces a non-device-dependent variable DEFAULT_SOC, which is used if no specific SOC is set for a device, and thus reduces the number of redundant definitions drastically. This is applied to all subtargets except xway, as only the latter has two different SOCs. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* lantiq: move DTS_DIR variable out of Device definitionAdrian Schmutzler2020-01-241-1/+2
| | | | | | | | | The DTS_DIR variable is not a device variable, thus it should not be set inside Device/Default but globally. Fixes: c640370939d7 ("lantiq: use soc_vendor_device scheme on DTS file") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* lantiq: fix model name for BT Home Hub 3 Type AAdrian Schmutzler2020-01-241-1/+1
| | | | | | | | | The number 3 was accidentally removed from the name during split of DEVICE_TITLE. Fixes: fd666870582f ("lantiq: split up DEVICE_TITLE") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: define SOC only once for uniform targetsAdrian Schmutzler2020-01-244-114/+7
| | | | | | | | | | | In ramips, all devices in mt7621, mt76x8 and rt288x subtarget have the same value set to the SOC variable for each device individually. This patch introduces a non-device-dependent variable DEFAULT_SOC, which is used if no specific SOC is set for a device, and thus reduces the number of redundant definitions drastically. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: act_ctinfo: really fix backport this timeKevin Darbyshire-Bryant2020-01-241-1/+1
| | | | Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* kernel: act_ctinfo: fixup build error on 4.14Kevin Darbyshire-Bryant2020-01-241-2/+3
| | | | Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* kernel: bump 4.19 to 4.19.98Koen Vandeputte2020-01-2411-19/+18
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.167Koen Vandeputte2020-01-247-10/+9
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: act_ctinfo: backport memory leak fixKevin Darbyshire-Bryant2020-01-242-8/+29
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 09d4f10a5e78d76a53e3e584f1e6a701b6d24108 ] Implement a cleanup method to properly free ci->params BUG: memory leak unreferenced object 0xffff88811746e2c0 (size 64): comm "syz-executor617", pid 7106, jiffies 4294943055 (age 14.250s) hex dump (first 32 bytes): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ c0 34 60 84 ff ff ff ff 00 00 00 00 00 00 00 00 .4`............. backtrace: [<0000000015aa236f>] kmemleak_alloc_recursive include/linux/kmemleak.h:43 [inline] [<0000000015aa236f>] slab_post_alloc_hook mm/slab.h:586 [inline] [<0000000015aa236f>] slab_alloc mm/slab.c:3320 [inline] [<0000000015aa236f>] kmem_cache_alloc_trace+0x145/0x2c0 mm/slab.c:3549 [<000000002c946bd1>] kmalloc include/linux/slab.h:556 [inline] [<000000002c946bd1>] kzalloc include/linux/slab.h:670 [inline] [<000000002c946bd1>] tcf_ctinfo_init+0x21a/0x530 net/sched/act_ctinfo.c:236 [<0000000086952cca>] tcf_action_init_1+0x400/0x5b0 net/sched/act_api.c:944 [<000000005ab29bf8>] tcf_action_init+0x135/0x1c0 net/sched/act_api.c:1000 [<00000000392f56f9>] tcf_action_add+0x9a/0x200 net/sched/act_api.c:1410 [<0000000088f3c5dd>] tc_ctl_action+0x14d/0x1bb net/sched/act_api.c:1465 [<000000006b39d986>] rtnetlink_rcv_msg+0x178/0x4b0 net/core/rtnetlink.c:5424 [<00000000fd6ecace>] netlink_rcv_skb+0x61/0x170 net/netlink/af_netlink.c:2477 [<0000000047493d02>] rtnetlink_rcv+0x1d/0x30 net/core/rtnetlink.c:5442 [<00000000bdcf8286>] netlink_unicast_kernel net/netlink/af_netlink.c:1302 [inline] [<00000000bdcf8286>] netlink_unicast+0x223/0x310 net/netlink/af_netlink.c:1328 [<00000000fc5b92d9>] netlink_sendmsg+0x2c0/0x570 net/netlink/af_netlink.c:1917 [<00000000da84d076>] sock_sendmsg_nosec net/socket.c:639 [inline] [<00000000da84d076>] sock_sendmsg+0x54/0x70 net/socket.c:659 [<0000000042fb2eee>] ____sys_sendmsg+0x2d0/0x300 net/socket.c:2330 [<000000008f23f67e>] ___sys_sendmsg+0x8a/0xd0 net/socket.c:2384 [<00000000d838e4f6>] __sys_sendmsg+0x80/0xf0 net/socket.c:2417 [<00000000289a9cb1>] __do_sys_sendmsg net/socket.c:2426 [inline] [<00000000289a9cb1>] __se_sys_sendmsg net/socket.c:2424 [inline] [<00000000289a9cb1>] __x64_sys_sendmsg+0x23/0x30 net/socket.c:2424 Fixes: 24ec483cec98 ("net: sched: Introduce act_ctinfo action") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Cc: Kevin 'ldir' Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> Cc: Cong Wang <xiyou.wangcong@gmail.com> Cc: Toke Høiland-Jørgensen <toke@redhat.com> Acked-by: Kevin 'ldir' Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* kernel: fix dst reference leak in flow offloadFelix Fietkau2020-01-232-22/+24
| | | | | | Fixes a significant amount of leaked memory with lots of connections Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ath79: fix SUPPORTED_DEVICES not matching ar71xx board namesAdrian Schmutzler2020-01-234-12/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Based on a script for comparison, this fixes (hopefully) all errors in SUPPORTED_DEVICES for ar71xx->ath79 upgrade. Devices where old string is removed as the device does not exist in ar71xx: - dlink_dir-859-a1 - tplink_archer-a7-v5 - tplink_cpe510-v3 Devices where string is changed because it did not match the board name in ar71xx: - tplink_tl-mr3220-v1 - tplink_tl-mr3420-v1 - tplink_tl-wr2543-v1 - tplink_tl-wr741nd-v4 - tplink_tl-wr841-v7 - ubnt_unifiac-mesh - ubnt_unifiac-mesh-pro - ubnt_unifiac-pro For this device, the correct string could not be found, but we could not determine the correct one. Thus, the string is removed for now: - tplink_tl-wr740n-v4 The script for checking this is quite simple (note that newer entries, i.e. ath79->ath79 upgrade, are displayed as missing): newpath=target/linux/ath79/image/ oldpath=target/linux/ar71xx/base-files/lib/ar71xx.sh for s in $(grep -roh "SUPPORTED_DEVICES.*" $newpath | sed 's/SUPPORTED_DEVICES *.= *//'); do found="Missing" grep -q -r "\"$s\"" $oldpath && found="Found" echo "$s: $found." done The errors might be filtered by appending 'grep "Missing"' to the script. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>