aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
* ath79: add support for Pisen WMM003N (Cloud Easy Power)Icenowy Zheng2018-08-143-0/+136
| | | | | | | | | | | | | | | | | | | | | Pisen WMM003N (sold under the name of Cloud Easy Power) is an AR9331-based router and power bank combo device. The device uses a stock firmware modified from OpenWRT for TP-Link TL-WR703N; however some GPIO definition is different on this device with TL-WR703N. An AXP202 PMIC (connected to a 5000mAh battery) and a SD slot are also added, and the stock Flash/RAM configuration is 8MiB/64MiB. The stock firmware is an old and heavily modified OpenWRT-based firmware, which has telnetd defaultly open, and the root password is "ifconfig" (quotation marks not included). The factory image format is not known yet, however the stock firmware ships the OpenWRT's sysupgrade command, and it can be used to install a newer firmware. Due to the lack of the access to the STM8 embedded controller, the SD slot is currently not usable (because it's muxed with the on-board USB port) and the AXP PMIC cannot be monitored. Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
* ar7: remove linux 3.18 supportKoen Vandeputte2018-08-1314-998/+0
| | | | | | | This target is on 4.9 currently. It seems the support for this old kernel never got dropped. Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ramips: add missing USB packages into ASL26555-16MZoltan HERPAI2018-08-131-1/+1
| | | | | | | Mirror the package list from the 8M device profile to the 16M device profile. Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* ath79: drop tl prefix for TP-Link RE450 v2Peter Lundkvist2018-08-132-2/+2
| | | | | | | | This router is called RE450 and the tl prefix was used to identify it as a TP-Link device. Drop the tl prefix since we now have tplink in dts and device name. Signed-off-by: Peter Lundkvist <peter.lundkvist@gmail.com>
* ath79: gmac: add parsers for rxd(v)- and tx(d|en)-delay for AR9344Christian Lamparter2018-08-132-1/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some AR9344 boards do very poorly with the default settings and need custom rxdv-delay, rxd-delay, txd-delay, txen-delay flags to perform reasonably. In this case the WD My Net Wi-Fi Range Extender can not even manage 10Mbps on a 1Gbit link: root@AR9344:~# iperf3 -s ----------------------------------------------------------- Server listening on 5201 ----------------------------------------------------------- Accepted connection from client [...] [ 5] local [...] connected to client [ ID] Interval Transfer Bitrate [ 5] 0.00-1.00 sec 1.09 MBytes 9.16 Mbits/sec [ 5] 1.00-2.00 sec 895 KBytes 7.33 Mbits/sec [ 5] 2.00-3.00 sec 762 KBytes 6.25 Mbits/sec [...] [ 5] 10.00-10.03 sec 17.0 KBytes 4.74 Mbits/sec - - - - - - - - - - - - - - - - - - - - - - - - - [ ID] Interval Transfer Bitrate [ 5] 0.00-10.03 sec 9.00 MBytes 7.52 Mbits/sec with but with the correct settings in place, it does much better: root@AR9344:~# iperf3 -s ----------------------------------------------------------- Server listening on 5201 ----------------------------------------------------------- Accepted connection from client [...] [ 5] local [...] connected to client [ ID] Interval Transfer Bitrate [ 5] 0.00-1.00 sec 23.1 MBytes 193 Mbits/sec [ 5] 1.00-2.00 sec 23.1 MBytes 194 Mbits/sec [ 5] 2.00-3.00 sec 23.2 MBytes 195 Mbits/sec [...] [ 5] 10.00-10.04 sec 710 KBytes 180 Mbits/sec - - - - - - - - - - - - - - - - - - - - - - - - - [ ID] Interval Transfer Bitrate [ 5] 0.00-10.04 sec 237 MBytes 198 Mbits/sec The tx data and enable delay bits definitions are taken from Atheros' AR9344 Data Sheet Section "8.6.1 Ethernet Configuration (ETH_CFG)" on page 153. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: add QCA956x GMAC configDavid Bauer2018-08-132-0/+18
| | | | | | This commit adds the ability to configure the GMAC of the QCA956x. Signed-off-by: David Bauer <mail@david-bauer.net>
* brcm47xx: cosmetic fix in model detectionPaul Wassi2018-08-131-1/+1
| | | | | | | | In "brcm47xx: rework model detection" the file 01_detect was moved to 01_network, therefore also update the warning message in case everything fails. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: ar913x: fix eth pll registerChuanhong Guo2018-08-131-1/+1
| | | | | | | PLL for eth0 internal clock on ar913x is at 0x18050014 and AR913X_ETH0_PLL_SHIFT is 20 instead of 17 Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: ag71xx: fix speed applied to MII0/1_CTRL on ar71xx/ar913xChuanhong Guo2018-08-131-2/+2
| | | | | | Currently speed value is applied to interface mode field. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: add WNDR3700 and WNDR3700v2Hannu Nyman2018-08-134-0/+93
| | | | | | | | | | | | Add support for WNDR3700 and WNDR3700v2. They share most things with WNDR3800. Only device IDs and partition structure needs to be set. Note: WNDR3700 (v1) has no NETGEAR_HW_ID, but has also the NA version of the factory image. Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* ath79: create WNDR3700 series .dtsi and adjust WNDR3800Hannu Nyman2018-08-133-200/+212
| | | | | | | | | | | | | | | | | Prepare for addition of WNDR3700 and WNDR3700v2 by separating the common parts into wndr3700.dtsi and leaving just the device-specific things into wndr3800.dts The three routers are identical except * device IDs * WNDR3700 (v1) has only 8 MB flash, while others have 16 MB. Partition structure needs to be defined for each device. * (WNDR3800 has 128 MB RAM, but RAM size is not in DTS) Also separate the common parts of the image recipe. (Drop also the initramfs recipe.) Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* ramips: fix BR-6478ACv2 supportDaniel Gimpelevich2018-08-136-70/+61
| | | | | | | | | | | | | | | | | The wholesale changes introduced in commit f9b8328 missed this DTS file because it hadn't been merged yet. This patch brings it in line to match the other mt7620a devices' DTS files. Additionally, the Internet LED is now labeled correctly and set to unused by default, since the WAN interface is not known in every configuration. Using sysupgrade between images before and after this commit will require the -F flag. Tested-by: Rohan Murch <rohan.murch@gmail.com> Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> [drop internet led default setting] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for Netgear R6120Ludwig Thomeczek2018-08-135-0/+180
| | | | | | | | | | | | | | | | | | | | This patch adds support for the Netgear R6120, aka Netgear AC1200. Specification: - SoC: MediaTek MT7628 (580 MHz) - Flash: 16 MiB - RAM: 64 MiB - Wireless: 2.4Ghz(builtin) and 5Ghz (MT7612E) - LAN speed: 10/100 - LAN ports: 4 - WAN speed: 10/100 - WAN ports: 1 - Serial baud rate of Bootloader and factory firmware: 57600 To flash use nmrpflash with the provided factory.img. Flashing via webinterface will not work, for now. Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
* at91: do not build image for at91-q5xr5Hauke Mehrtens2018-08-121-1/+1
| | | | | | | | The kernel image of the at91-q5xr5 is getting too bing now and this is breaking the build. Remove the image for the at91-q5xr5 from the build to at least build images for the other devices. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ath79: fix eth pll for ar913xChuanhong Guo2018-08-111-1/+1
| | | | | | PLL node is missing syscon in compatible string. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: add support for I-O DATA WN-AC1600DGR2INAGAKI Hiroshi2018-08-116-9/+252
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-AC1600DGR2 is a 2.4/5 GHz band 11ac router, based on Qualcomm Atheros QCA9557. Specification: - Qualcomm Atheros QCA9557 - 128 MB of RAM - 16 MB of Flash - 2.4/5 GHz wifi - 2.4 GHz: 2T2R (SoC internal) - 5 GHz: 3T3R (QCA9880) - 5x 10/100/1000 Mbps Ethernet - 6x LEDs, 6x keys (4x buttons, 1x slide switch) - UART header on PCB - Vcc, GND, TX, RX from ethernet port side - 115200n8 Flash instruction using factory image: 1. Connect the computer to the LAN port of WN-AC1600DGR2 2. Connect power cable to WN-AC1600DGR2 and turn on it 3. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 4. Select the OpenWrt factory image and click update ("更新") button 5. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: add support of D-Link DIR-825 B1Dmitry Tunin2018-08-114-0/+288
| | | | | | Add support for the ar71xx supported D-Link DIR-825 B1 to ath79. Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
* ath79: add ath9k calibration data MAC addresses patchingChristian Lamparter2018-08-111-0/+50
| | | | | | | | | | | | | | | | | | This patch copies over the MAC patching helper functions from lantiq's target/linux/lantiq/base-files/etc/hotplug.d/firmware/12-ath9k-eeprom file. Not all vendors bothered to write the correct MAC addresses for the ath9k wifi into the calibration data. And while ath9k does have some special dt-properties to extract the addresses from a fixed position, there are still devices that require userspace to edit or modify the caldata. In my case, the MAC address for the Wi-Fi device is stored in an unsorted key-value based "nvram" database and there's an existing userspace tool to extract the data. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: add support for TP-Link TL-WDR4900 v2Chuanhong Guo2018-08-114-2/+245
| | | | | | | | | | | | | | Specification: - SoC: Qualcomm Atheros QCA9558 - Flash: 8 MB - RAM: 128 MB - Ethernet: AR8327N with 5 GE ports. - Wireless radio: QCA9558 for 2.4G and AR9580 for 5G. Flash instruction: Upload the generated factory firmware on web interface. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* kernel: bump 4.14 to 4.14.62Koen Vandeputte2018-08-104-21/+8
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx, imx6, x86_64 Runtime-tested on: cns3xxx, imx6, x86_64 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.119Koen Vandeputte2018-08-104-95/+13
| | | | | | | | | | | | Refreshed all patches. Delete upstreamed patch: - 100-tcp-add-tcp_ooo_try_coalesce-helper.patch Compile-tested on: ar71xx Runtime-tested on: ar71xx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: add support for OCEDO KoalaDavid Bauer2018-08-094-0/+184
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the OCEDO Koala SOC: Qualcomm QCA9558 (Scorpion) RAM: 128MB FLASH: 16MiB WLAN1: QCA9558 2.4 GHz 802.11bgn 3x3 WLAN2: QCA9880 5 GHz 802.11nac 3x3 INPUT: RESET button LED: Power, LAN, WiFi 2.4, WiFi 5, SYS Serial: Header Next to Black metal shield Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V) The Serial setting is 115200-8-N-1. Tested and working: - Ethernet - 2.4 GHz WiFi - 5 GHz WiFi - TFTP boot from ramdisk image - Installation via ramdisk image - OpenWRT sysupgrade - Buttons - LEDs Installation seems to be possible only through booting an OpenWRT ramdisk image. Hold down the reset button while powering on the device. It will load a ramdisk image named 'koala-uImage-initramfs-lzma.bin' from 192.168.100.8. Note: depending on the present software, the device might also try to pull a file called 'koala-uimage-factory'. Only the name differs, it is still used as a ramdisk image. Wait for the ramdisk image to boot. OpenWRT can be written to the flash via sysupgrade or mtd. Due to the flip-flop bootloader which we not (yet) support, you need to set the partition the bootloader is selecting. It is possible from the initramfs image with > fw_setenv bootcmd run bootcmd_1 Afterwards you can reboot the device. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: ag71xx: remove PHY resetChuanhong Guo2018-08-096-22/+6
| | | | | | | | | | | | Bit 8/12 of reset controller which is marked as PHY_RESET/SWITCH_RESET in datasheets will trigger either a reset for builtin switch or assert an external ETH0_RESET_L/ETH1_RESET_L pin, which are usually connected to external PHY/switch. None of them should be triggered every time an interface is brought up in ethernet driver. Remove PHY reset support from ag71xx and definition for them in dtsi. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: add support for Buffalo BHR-4GRV2INAGAKI Hiroshi2018-08-096-9/+179
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Buffalo BHR-4GRV2 is a wired router, based on Qualcomm Atheros QCA9558. Ported from ar71xx target. Specification: - Qualcomm Atheros QCA9558 - 64 MB of RAM - 16 MB of Flash - 5x 10/100/1000 Ethernet - QCA8337N - 4x LEDs, 2x keys - UART header on PCB - Vcc, TX, RX, GND from LED side - 115200n8 Flash instruction using factory image: 1. Connect the computer to the LAN port of BHR-4GRV2 2. Connect power cable to BHR-4GRV2 and turn on it 3. Access to "http://192.168.12.1/" and open firmware update page ("ファームウェア更新") 4. Select the OpenWrt factory image and click update ("更新実行") button 5. Wait ~120 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: fix PLL settings for QCA955xDavid Bauer2018-08-093-2/+10
| | | | | | | | | | | | | | This adds PLL settings for the ethernet ports of the TP-Link TL-WR1043 v2/v3 and the Openmesh OM5P-AC-v2. We also change the PLL-settings in the qca9557.dtsi to match the ones used as default on the ar71xx target. As of 4b9680f138 those devices have broken ethernet ports as the default PLL settings defined in the QCA9557.dtsi are applied which are off for those devices. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add pll for archer c7Kevin Darbyshire-Bryant2018-08-091-0/+2
| | | | | | | | | | | | | | | | | | commit 4b9680f fixed pll settings and the correct pll set by bootloader is overrided by value in qca9557.dtsi which is incorrect for Archer C7 and breaks ethernet. Add pll values for archer c7 to fix ethernet connection. This individual pll tweak has been cherry picked from github pr 1260 which changes a couple of things in a single commit and should be ideally split. This commit get archer v7 back and working. Tested: archer c7 v2 Original combined commit authored by: Signed-off-by: Chuanhong Guo <gch981213@gmail.com> c7 fix only split out by: Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* sunxi: change Orange Pi PC2 MUSB/power buttonAntonio Silverio2018-08-091-0/+20
| | | | | | | Changed default role of Orange Pi PC2 MSUB port to host (in dts) Changed default function of Orange Pi PC2 power button to PWR_BTN Signed-off-by: Antonio Silverio <menion@gmail.com>
* sunxi: Added support for Xunlong Orange Pi PC2Antonio Silverio2018-08-091-0/+10
| | | | | | | | | | | | | | | | CPU: H5 High Performance Quad-core 64-bit Cortex-A53 GPU: Mali450 OpenGL ES 2.0/1.1/1.0, OpenVG 1.1, EGL Memory: 1GB DDR3 (shared with GPU) Onboard Storage: TF card (Max. 32GB) / NOR flash(2MB) Onboard Network: 1000M/100M Ethernet RJ45 USB 2.0 Ports: Three USB 2.0 HOST, one USB 2.0 OTG, HOST mode role by default in DTS Buttons: Power Button(SW4) Debug TTL UART: ..DC-IN.. >[GND][RX][TX] ..HDMI.. Signed-off-by: Antonio Silverio <menion@gmail.com>
* kernel: move e1000e patches to backportsStijn Tintel2018-08-094-0/+0
| | | | | | They're already in linux.git, so they shouldn't be in pending. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* cns3xxx: correct size specifier in watchdog init printKoen Vandeputte2018-08-081-1/+1
| | | | | | | fix compiler warnings Fixes: 84acff286566 ("cns3xxx: fix mpcore watchdog") Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* cns3xxx: delete invalid snip in patchKoen Vandeputte2018-08-081-1/+0
| | | | Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx: allow to override at803x sgmii aneg statusDavid Bauer2018-08-082-0/+43
| | | | | | | | | | | | | When checking the outcome of the PHY autonegotiation status, at803x currently returns false in case the SGMII side is not established. Due to a hardware-bug, ag71xx needs to fixup the SoCs SGMII side, which it can't as it is not aware of the link-establishment. This commit allows to ignore the SGMII side autonegotiation status to allow ag71xx to do the fixup work. Signed-off-by: David Bauer <mail@david-bauer.net>
* ar71xx: fix QCA955X SGMII link lossDavid Bauer2018-08-085-0/+127
| | | | | | | | | | | | | | | | | | | The QCA955X is affected by a hardware bug which causes link-loss of the SGMII link between SoC and PHY. This happens on change of link-state or speed. It is not really known what causes this bug. It definitely occurs when using a AR8033 Gigabit Ethernet PHY. Qualcomm solves this Bug in a similar fashion. We need to apply the fix on a per-device base via platform-data as performing the fixup work will break connectivity in case the SGMII interface is connected to a Switch. This bug was first proposed to be fixed by Sven Eckelmann in 2016. https://patchwork.ozlabs.org/patch/604782/ Based-on-patch-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> Signed-off-by: David Bauer <mail@david-bauer.net>
* kernel: allow device-tree configuration of at803xDavid Bauer2018-08-081-0/+49
| | | | | | | | | | This commit adds the ability to configure specific functions of the at803x series ethernet-PHYs, which were previously configured exclusively with the help of platform-data, via device-tree. This is needed to fully support existing boards of the ar71xx platform. Signed-off-by: David Bauer <mail@david-bauer.net>
* kernel: backport upstream fix for CVE-2018-5390Jo-Philipp Wich2018-08-081-0/+76
| | | | | | | | | | Backport an upstream fix for a remotely exploitable TCP denial of service flaw in Linux 4.9+. The fixes are included in Linux 4.14.59 and later but did not yet end up in version 4.9.118. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ath79: fix QCA9557 eth PLL settingsDavid Bauer2018-08-081-1/+7
| | | | | | | | The QCA9557 dtsi is currently missing pll-handle and pll-regs for both eth0 and eth1, therefore PLL settings won't be applied. This commit fixes this behavior. Signed-off-by: David Bauer <mail@david-bauer.net>
* mediatek: Fix amount of memory on U7623Kristian Evensen2018-08-081-16/+19
| | | | | | | | | | | | | | | While finalizing support for the U7623 with 512MB, I made an embarresing error and configured 1GB RAM for the board. I also forgot to move memory from the dtsi and to the dts. This commit takes care of my mistakes. While I am confessing my mistakes, I also note that I made a mistake in the commit message of the initial U7623 commit. It is the .bin-file, and not the .gz file that shall be sent to the device via tftp. v1->v2: * Remove redundant memory node (thanks Jonas Gorski) Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
* ath79: don't include tl-wdr3600 image build code for tl-wdr4300Mathias Kresin2018-08-081-1/+3
| | | | | | | | | | Including the tl-wdr3600 image build code just to overwrite most of it doesn't make much sense and only makes it hard to read. Furthermore, the tl-wdr4300 image will be marked as compatible with the tl-wdr3600 this way. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: cleanup netgear wnr612-v2 supported devicesMathias Kresin2018-08-081-1/+1
| | | | | | | The netgear,wnr612-v2 is included by default based on the device define. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: mark netgear variables as device specificMathias Kresin2018-08-081-0/+2
| | | | | | | | The variables are used in image build recipes and need to be marked as per devices vars to be stored individual per image define. Otherwise the last defined variable will be used for all boards. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: Fix led nodes for TL-WR740N v2 and add its clonesChuanhong Guo2018-08-0811-28/+138
| | | | | | | | | | | | | | | | This patch did the following things: 1. Separate ath9k-leds out of gpio leds so that all other leds will work before ath9k loded (e.g. during preinit/init stage). 2. Rename wps led to qss since that's how TP-Link mark it. 3. Rename LED prefix to tp-link because that dts is shared by many devices. 4. Rename to wr740n-v1 because v1 is the first and v2 just use the fw of v1. (This will require a forced sysupgrade if you comes from the previous wr740n v2 image.) 5. Remove SUPPORTED_DEVICES. (tl-wr740n-v2 doesn't exist anywhere so it's useless.) 6. Add all WR741ND v1 clones found in ar71xx. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: fix dts warningsMathias Kresin2018-08-0845-188/+90
| | | | | | | Fix all issues found by the devicetree compiler like wrong address/size cells as well as wrong/missing/superfluous unit addresses. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: fix node namesMathias Kresin2018-08-089-9/+9
| | | | | | Use the standardized node names from the devicetree specification. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: fix compatible stringsMathias Kresin2018-08-085-5/+5
| | | | | | | Use only the jedec,spi-nor compatible string. Everything else either never worked or is only support to keep compatibility. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: fix whitespace issue in dts filesMathias Kresin2018-08-088-24/+24
| | | | | | Fixes spaces vs. tabs issues and remove indentation on blank lines. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: use #include syntax for dtsi filesMathias Kresin2018-08-082-2/+2
| | | | | | Use the same syntax for including dtsi for all dts files. Signed-off-by: Mathias Kresin <dev@kresin.me>
* cns3xxx: ethernet: use circular queue checks consistentlyKoen Vandeputte2018-08-071-15/+18
| | | | | | | Use the same method for setting queue index pointers consistenly throughout the source file. Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* cns3xxx: ethernet: cleanup codeKoen Vandeputte2018-08-071-13/+22
| | | | Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* cns3xxx: ethernet: fix signed/unsigned comparisonKoen Vandeputte2018-08-071-1/+1
| | | | | | Fixes a compiler warning Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* cns3xxx: add myself as maintainerKoen Vandeputte2018-08-071-2/+2
| | | | Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-10-30 09:57:32 +0000