aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
...
* kernel: fix section mismatch in crashlogHauke Mehrtens2016-03-054-4/+4
| | | | | | | | | | | | | | | The function memblock_insert_region() is in the section __init_memblock, also put crashlog_init_memblock there. This fixes this section mismatch warning: The function memblock_insert_region.isra.1() references the function __meminit crashlog_init_memblock(). This is often because memblock_insert_region.isra.1 lacks a __meminit annotation or the annotation of crashlog_init_memblock is wrong. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 48931
* kernel: add missing config optionsHauke Mehrtens2016-03-056-4/+8
| | | | | | | | | | The buildbots complained about these config options being missing for arm64: CONFIG_DUMMY_CONSOLE_COLUMNS=80 CONFIG_DUMMY_CONSOLE_ROWS=25 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 48929
* ar71xx: WNR612v2: enable control of all LEDs and buttonsFelix Fietkau2016-03-052-2/+74
| | | | | | | | | This patch provides full GPIO support for WNR612v2 (LEDs and buttons). It exposes all LEDs to operating system, including Ethernet ones. Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl> SVN-Revision: 48924
* ar71xx: WNR2000v3: add speed_mask to Ethernet port LED initializationFelix Fietkau2016-03-051-8/+8
| | | | | | | | | | This patch add speed_mask parameter to Ethernet port LED initialization during system startup. LEDs are configured to show amber light for 10 Mbps link and green for 100 Mbps as described on device label. Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl> SVN-Revision: 48923
* ar71xx: WNR2000v3: enable control of all LEDs and buttonsFelix Fietkau2016-03-053-10/+143
| | | | | | | | | This patch provides full GPIO support for WNR2000v3 (LEDs and buttons). It exposes all LEDs to operating system, including Ethernet ones. Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl> SVN-Revision: 48922
* mac80211: ath9k: enable GPIO buttonsFelix Fietkau2016-03-053-0/+25
| | | | | | | | | | Enable platform-defined GPIO button support for ath9k device. Key poller is activated for attached platform buttons. Requires ath9k GPIO chip access. Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl> SVN-Revision: 48921
* AP121 target: fix board detection in ar71xx.shJohn Crispin2016-03-041-1/+1
| | | | | | Signed-off-by: Attila Lendvai <attila@lendvai.name> SVN-Revision: 48916
* AR8216: improve mmd register accessJohn Crispin2016-03-043-13/+17
| | | | | | | | | | | Combine all bus operations for one MMD access in one function. Protecting all these bus operations with one lock also helps to avoid potential issues due to bus operations intercepting the register and data write. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> SVN-Revision: 48914
* AR8216: make ARL age time configurableJohn Crispin2016-03-044-4/+80
| | | | | | | | | | | | | | | | | The default TTL for address resolution table entries is 5 minutes for all members of the AR8216 family. This can cause issues if e.g. Wifi clients roam to another AP and their MAC appears on another switch port suddenly. Then the client may not be reachable until the old ARL entry expires. I would have expected the switch to invalidate old entries if it detects the same MAC on another port. But that's not the case. Therefore make the TTL for ARL entries configurable. The effective TTL will always be a multiple of 7 seconds. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> SVN-Revision: 48913
* AR8216: remove redundant port number in MIB header lineJohn Crispin2016-03-041-2/+1
| | | | | | | | | The line before includes the port number anyway so there's no need to duplicate the port number in the MIB info header. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> SVN-Revision: 48912
* AR8216: complement MIB counters with info in GiB / MiB / KiBJohn Crispin2016-03-041-5/+40
| | | | | | | | | | The decimal values especially for TxByte and RxGoodByte are hard to read once bigger amounts of data have been transferred. Therefore complement the decimal values with info in GiB / MiB / KiB. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> SVN-Revision: 48911
* AR8216: don't display MIB counters if all are emptyJohn Crispin2016-03-041-1/+8
| | | | | | | | | | | | For unused switch ports all MIB values are zero. Displaying ~40 empty MIB counters is just confusing and makes it hard to read the output of swconfig dev <dev> show. Therefore, if all MIB counters for a port are zero, just display an info that the MIB counters are empty. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> SVN-Revision: 48910
* imx6: image: Add missing kernel prefixJohn Crispin2016-03-041-0/+1
| | | | | | Signed-off-by: Petr Štetiar <ynezz@true.cz> SVN-Revision: 48909
* ramips: mt7621: fix WF-2881 for ubi splitJohn Crispin2016-03-042-14/+5
| | | | | | | | This patch fix firmware split for WF-2881 which was previously manually partitioned. Signed-off-by: YounJae Rho <luxflow@live.com> SVN-Revision: 48908
* ramips: Add profiles for JCG routersJohn Crispin2016-03-042-0/+60
| | | | | | | | | | This patch adds profiles and support for building factory and sysupgrade images for JHR-N805R, JHR-N825R and JHR-N926R. Signed-off-by: Reinhard Max <reinhard@m4x.de> Reviewed-by: Torsten Duwe <duwe@lst.de> SVN-Revision: 48906
* ramips: Add JCG routers to base-filesJohn Crispin2016-03-044-0/+18
| | | | | | | | | | This patch adds support for JHR-N805R, JHR-N825R and JHR-N926R to various scripts in the base-files directory. Signed-off-by: Reinhard Max <reinhard@m4x.de> Reviewed-by: Torsten Duwe <duwe@lst.de> SVN-Revision: 48905
* ramips: Add device tree for JCG JHR-N926RJohn Crispin2016-03-041-0/+127
| | | | | | | | | | | | | | | | Add a device tree for JCG JHR-N825R This router is based on a RT3052 and has 4MB of CFI flash and 32MB of SDRAM. As a special feature, it comes with a two digit seven segment display that is connected to a pair of daisy-chained 74164 shift registers that can be controlled via GPIOs. For details, see https://wikidevi.com/wiki/JCG_JHR-N825R . Signed-off-by: Reinhard Max <reinhard@m4x.de> Reviewed-by: Torsten Duwe <duwe@lst.de> SVN-Revision: 48904
* ramips: Add device tree for JCG JHR-N825RJohn Crispin2016-03-041-0/+81
| | | | | | | | | | | | Add a device tree for JCG JHR-N825R This router is based on a RT3052 and has 4MB of CFI flash and 32MB of SDRAM. For details, see https://wikidevi.com/wiki/JCG_JHR-N825R . Signed-off-by: Reinhard Max <reinhard@m4x.de> Reviewed-by: Torsten Duwe <duwe@lst.de> SVN-Revision: 48903
* ramips: Add device tree for JCG JHR-N805RJohn Crispin2016-03-041-0/+89
| | | | | | | | | | | | Add a device tree for JCG JHR-N805R This router is based on a RT3050 and has 4MB of SPI flash and 16MB of SDRAM. For details, see https://wikidevi.com/wiki/JCG_JHR-N805R . Signed-off-by: Reinhard Max <reinhard@m4x.de> Reviewed-by: Torsten Duwe <duwe@lst.de> SVN-Revision: 48902
* ramips: Incorrect file mode changeJohn Crispin2016-03-034-0/+0
| | | | | | | | | | | Commit d0f5ab6d95a1 ("ramips: Added support for ZBT-826 / ZBT-1026") incorrectly changed the mode of the ramips shell scripts from 755 to 644. I.e., they are not excutable any more and for example devices will be left with broken configs. Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com> SVN-Revision: 48893
* target/mpc85xx: check for 'generic' subtarget for initramfs image fileJohn Crispin2016-03-031-0/+2
| | | | | | | | | | | | | Copy 'cuImage.tl-wdr4900-v1-initramfs' only for the 'generic' subtarget. This is a follow-up to: http://git.openwrt.org/?p=openwrt.git;a=commitdiff;h=b889fe55c1844aec2c03da28fecb03e958c21f18 We build our initramfs images more rarely, so it took a while to catch this too. Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com> SVN-Revision: 48892
* ramips: enable mt76 on mt7688 by defaultFelix Fietkau2016-03-022-0/+4
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 48886
* mac80211: ath9k: enable platform WLAN LED nameFelix Fietkau2016-03-023-0/+16
| | | | | | | | | Enable platform-supplied WLAN LED name for ath9k device. Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl> Acked-by: Hartmut Knaack <knaack.h@gmx.de> SVN-Revision: 48879
* kernel: update kernel 3.18 to version 3.18.27Hauke Mehrtens2016-03-015-5/+5
| | | | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 48874
* ar71xx: Add OOLITE to the Gainstrong profile, removed standalone profile.John Crispin2016-03-012-18/+11
| | | | | | | | | This patch moves the OOLITE profile code into the overarching Gainstrong profile and deletes the old single profile file. Signed-off by: Stijn Segers <francesco.borromini@inventati.org> SVN-Revision: 48866
* ramips: Added support for ZBT-826 / ZBT-1026John Crispin2016-03-017-0/+155
| | | | | | | | | Support for these MT7620-based routers: https://wiki.openwrt.org/toh/zbt/we-826 Based on Oskari’s patches found here: https://dev.openwrt.org/ticket/19996 Signed-off-by: Jamie Stuart <jamie@onebillion.org> SVN-Revision: 48865
* ar71xx, firmware-utils: split ubdev01 flash layout from XMFelix Fietkau2016-02-291-1/+1
| | | | | | | | | The ubdev01 profile defines its own MTDPARTS with smaller firmware partition, so give it its own UBNT_BOARD in mkfwimage. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> SVN-Revision: 48828
* ramips: add sysupgrade support for mt7628Felix Fietkau2016-02-281-0/+1
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 48813
* ramips: create device tree node for MT7628 WMAC in preparation for future ↵Felix Fietkau2016-02-282-0/+17
| | | | | | | | work on driver support in mt76 Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 48812
* Revert "ar71xx: WNR612v2: exclude USB modules from image"Felix Fietkau2016-02-261-1/+0
| | | | | | | | This reverts commit r48778. The issue has now been fixed properly Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 48808
* kernel: use upstream accepted bcm47xxpart patchesRafał Miłecki2016-02-262-3/+6
| | | | | | Signed-off-by: Rafał Miłecki <zajec5@gmail.com> SVN-Revision: 48805
* kernel: disable MIPS VDSO by default until the cache issues have been resolvedFelix Fietkau2016-02-261-0/+21
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 48802
* ar71xx: Renamed Gainstrong MiniBox profile to Gainstrong (manufacturer) and ↵John Crispin2016-02-261-1/+1
| | | | | | | | | | | | | | | | updated copyright This is the first patch of a series of three to tidy up the profiles for Gainstrong devices. Right now there are two Gainstrong profiles, each for a single device built by this manufacturer. This patch renames the MiniBox profile to Gainstrong and updates the copyright notice. The series applies cleanly to current trunk. Resent with the architecture in the subject, forgot that the first time. Signed-off by: Stijn Segers <francesco.borromini@inventati.org> SVN-Revision: 48797
* ramips: fix GPIO names for RT5350F-OLinuXino-EVBJohn Crispin2016-02-261-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hi, the board in subject (RT5350F-OLinuXino-EVB) still ships from vendor with a RC3 image built upon a .dts file which declares GPIO12 and GPIO14 as relay2 and relay1 respectively, as you can see from their rt5350f branch on GitHub. For some reason in the official stable build both the GPIOs are swapped and the wrong names are declared in the gpio-export directive. I'm submitting this patch which should roll back the wrong changes, so that we get backward compatibility with any script developed on RC3 which controls the relays. After patching correct operation is restored: root@OpenWrt:/# cat /sys/kernel/debug/gpio GPIOs 0-21, platform/10000600.gpio, 10000600.gpio: gpio-0 (button ) in hi gpio-12 (relay2 ) out lo gpio-14 (relay1 ) out lo Thank you, Signed-off-by: Lorenzo Cafaro <lorenzo@ibisco.net> SVN-Revision: 48796
* mpc85xx/tl-wdr4900: correct address of the gpio controllerJohn Crispin2016-02-261-1/+1
| | | | | | | | since linux 3.19 the address of the gpio-controller changed Signed-off-by: Alexander Couzens <lynxis@fe80.eu> SVN-Revision: 48794
* kernel: deactivate the vdso gettimeofday function.Hauke Mehrtens2016-02-251-0/+9
| | | | | | | | | | The vdso version of this function has some problems with the cache. Very often it works on dated data which causes problem. We are currently working on fixing this in upstream Linux kernel. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 48787
* kernel: update kernel 4.4 to version 4.4.3Hauke Mehrtens2016-02-2529-314/+83
| | | | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 48783
* ar71xx: WNR612v2: fix for random WLAN MACFelix Fietkau2016-02-251-1/+7
| | | | | | | | | | Fix for invalid/random WLAN MAC address in WNR612v2. Permanent platform MAC is calculated and assigned during system startup. WLAN MAC follows wired Ethernet interface addresses. This is the same fix as for WNR2000v3. Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl> SVN-Revision: 48779
* ar71xx: WNR612v2: exclude USB modules from imageFelix Fietkau2016-02-251-0/+1
| | | | | | | | | Netgear WNR612v2 has no USB port yet default system image includes USB kernel modules. This patch fixes that. Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl> SVN-Revision: 48778
* ar71xx: WNR2000v3: fix for random WLAN MACFelix Fietkau2016-02-251-6/+41
| | | | | | | | | | Fix for invalid/random WLAN MAC address in WNR2000v3. Permanent platform MAC is calculated and assigned during system startup. WLAN MAC follows wired Ethernet interface addresses. Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl> SVN-Revision: 48777
* switch: allow Ethernet port LEDs to show specific port speeds onlyFelix Fietkau2016-02-251-5/+99
| | | | | | | | | | | | | This patch adds speed_mask special file to LEDs connected to switch ports via 'switch' trigger. It allows to choose which speeds to signal when link is up. If router has more than one LED per port, they may light up differently depending on how fast connection is. Default setting is 'all speeds' so backward compatibility with system scripts (for example uci) is maintained. Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl> SVN-Revision: 48775
* switch: make LED port_mask file write handler use kstrtoul() functionFelix Fietkau2016-02-251-25/+16
| | | | | | | | | | | This patch changes swconfig_trig_port_mask_store() handler to utilize kstrtoul() function instead of call to obsolete simple_strtoul(). Thanks to this change, new handler takes less memory and makes port_mask special file accept not only hexadecimal, but also decimal and octal numbers. Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl> SVN-Revision: 48774
* ramips: mt7620: fix failsafe switch configJohn Crispin2016-02-251-0/+14
| | | | | | | | | | | | | | | | | | | | | | | | As indicated in the bug tracker[1], failsafe mode is broken on at least some devices using the mt7620 switch (and possibly mt7621). The thread explicitly mentions the Xiaomi MiWifi, and the Nexx WT3020, and an unspecified device using the mt7621 switch; the issue also applies to the Netgear EX2700. The problem is that failsafe mode uses eth0, but enable_vlan is always set to 1 by the switch driver. Connecting to and/or pinging the device fails. This patch fixes the failsafe preinit config, by making sure that vlan support is disabled. It currently only fixes the switch config on mt7620, but might apply to the mt7621 as well, so the patch has been designed with this in mind. A similar (line wrapped) patch was submitted in December by Simon Peter, but never accepted and/or discussed. This patch applies to both Chaos Calmer and trunk. [1] https://dev.openwrt.org/ticket/18768 Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com> SVN-Revision: 48772
* ramips: build factory images for Netgear EX2700John Crispin2016-02-252-1/+27
| | | | | | | | | | | | | | | | This patch adds support for building factory and sysupgrade images for the Netgear EX2700 that don't require modification of u-boot environment variables. The bootloader on this device expects the kernel partition to end on a 64k block boundary. The last 64 byte of the kernel partition must contain a valid uImage header - in the stock firmware, this is the uImage header of the root filesystem. For this patch, we're using the uImage header of a 0 byte partition (ex2700-fakeroot.uImage). Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com> SVN-Revision: 48771
* ar71xx: correct imagename for TPlink WA730REJohn Crispin2016-02-251-2/+2
| | | | | | | | - insert missing "-" to separate model and version Signed-off-by: Sven Roederer <devel-sven@geroedel.de> SVN-Revision: 48769
* ar71xx: correct imagename for TPlink WA701NDJohn Crispin2016-02-251-2/+2
| | | | | | | | - it seems there was never a 701N-model build Signed-off-by: Sven Roederer <devel-sven@geroedel.de> SVN-Revision: 48768
* ar71xx: matchup of TPlink WR841N(D)-namesJohn Crispin2016-02-251-8/+8
| | | | | | | | | | | | | - remove the suffix (N, ND) to indicate that the image is for all WR841-models - some of these models have a "N"-suffix, others have (ND)-suffix, but the boards are the same - only difference is the detachable antenna on "D"-models - discussed this idea to remove the suffix in IRC with jow and Borromini Signed-off-by: Sven Roederer <devel-sven@geroedel.de> SVN-Revision: 48767
* brcm2708: remove linux 4.1 supportJohn Crispin2016-02-25216-151539/+10
| | | | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> SVN-Revision: 48766
* brcm2708: switch to linux 4.4 and update patchesJohn Crispin2016-02-25155-272/+5594
| | | | | | | | | As usual these patches were extracted from: https://github.com/raspberrypi/linux/commits/rpi-4.4.y Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> SVN-Revision: 48765
* sunxi: add descriptor files for wifi+bt modules (AP6181/6210), add brcmfmac ↵Zoltan Herpai2016-02-243-1/+110
| | | | | | | | to bananapro profile Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu> SVN-Revision: 48757
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-02 17:25:17 +0000