aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
* kernel/4.4: add missing newline character to UBI messagesGabor Juhos2017-12-242-4/+4
| | | | | | | | | | | | | | | A few UBI messages lacks the trailing newline character which leads to ugly lines in the bootlog like this: [ 6.649159] UBI error: no valid UBI magic found inside mtd6[ 6.667751] Freeing unused kernel memory: 2196K Add a newline character to the end of the messages to fix it. After the fix the line from above looks better in the log: [ 6.609182] UBI error: no valid UBI magic found inside mtd6 [ 6.627599] Freeing unused kernel memory: 2132K Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
* kernel: bump 4.4 to 4.4.107Kevin Darbyshire-Bryant2017-12-2317-64/+64
| | | | | | | | | | Refresh patches. Update patch that no longer applied: oxnas/0072-mtd-backport-v4.7-0day-patches-from-Boris.patch Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> Tested-by: Rosen Penev <rosenp@gmail.com>
* lantiq: remove DSL_ChipSetHWVersion from status informationMartin Schiller2017-12-231-4/+2
| | | | | | | | | | | | The value DSL_ChipSetHWVersion is fetched from the dsl frontend via the dsl_control service, but not really provided by the dsl frontend firmware and for now always "UNKNOWN". The lantiq support told us that this information wouldn't be provided in the foreseeable future, so let's remove this useless "UNKNOWN" information. Signed-off-by: Martin Schiller <ms@dev.tdt.de>
* ramips: fix Linkit smart 7688 supportMathias Kresin2017-12-233-24/+8
| | | | | | | | | | Use a more appropriate compatible string. Fix the wireless led GPIO and add the default wireless trigger. Use the wireless LED for boot state indication as well. Remove the GPIO pinmux for pins not exposed on the board. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for TP-Link TL-MR3420 v5Henryk Heisig2017-12-236-0/+109
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link TL-MR3420 v5 are simple N300 router with 5-port FE switch and non-detachable antennas. Its very similar to TP-Link TL-WR841N V13. Specification: - MT7628N/N (580 MHz) - 64 MB of RAM (DDR2) - 8 MB of FLASH - 2T2R 2.4 GHz - 5x 10/100 Mbps Ethernet - 2x external, non-detachable antennas - USB 2.0 Port - UART (J1) header on PCB (115200 8n1) - 8x LED, 2x button, power input switch Flash instruction: The only way to flash LEDE image in mr3420v5 is to use tftp recovery mode in U-Boot: 1. Configure PC with static IP 192.168.0.225/24 and tftp server. 2. Rename "lede-ramips-mt7628-tplink_tl-mr3420-v5-squashfs-tftp-recovery.bin" to "tp_recovery.bin" and place it in tftp server directory. 3. Connect PC with one of LAN ports, press the reset button, power up the router and keep button pressed for around 6-7 seconds, until device starts downloading the file. 4. Router will download file from server, write it to flash and reboot. Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ramips: move common tplink image build code into own recipeMathias Kresin2017-12-231-8/+20
| | | | | | | | Move common tplink image build code into own recipe. Include the common parts instead of including a full build recipe and overwriting former set varaibles. Signed-off-by: Mathias Kresin <dev@kresin.me>
* kernel: move console loglevel to genericTomasz Maciej Nowak2017-12-232-1/+1
| | | | | | | Move CONFIG_CONSOLE_LOGLEVEL_DEFAULT=7 to generic, to make it consistent across all targets. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* kernel: add missing config symbols for 4.14Stijn Tintel2017-12-211-0/+4
| | | | Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* ar71xx: add support for MikroTik RouterBOARD 921GS-5HPacD r2 (mANTBox 15s)Roger Pueyo Centelles2017-12-216-3/+26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the MikroTik RouterBOARD 921GS-5HPacD r2 (mANTBox 15s), an outdoor sector antenna with a built-in 802.11ac wireless router. Additionally, it adds a new profile for devices with >= 128 MB NAND flash and 802.11ac to the ar71xx/mikrotik subtarget. See https://mikrotik.com/product/RB921GS-5HPacD-15S for more info. Specifications: - SoC: Qualcomm Atheros QCA9558 (720 MHz) - RAM: 128 MB - Storage: 128 MB NAND - Wireless: external QCA9822 802.11a/ac 2x2:2 - Ethernet: 1x 1000/100/10 Mbps, integrated, via AR8031 PHY, passive PoE in - SFP: 1x host Working: - Board/system detection - NAND storage detection - Wireless - Ethernet - 1x user LED - Reset button - Sysupgrade Untested: - SFP cage (probably not working) Installation: - Boot initramfs image via TFTP and then flash sysupgrade image Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ar71xx: fix spelling in mach-rb922.cRoger Pueyo Centelles2017-12-211-1/+1
| | | | Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ar71xx: fix rb922gs_nand_scan_fixup()Roger Pueyo Centelles2017-12-211-1/+5
| | | | | | | | | Apply code from commits 9e1bc27e6d67fa29791eb0fac5e5f0066d12a761 (ar71xx: Fix UBIFS work on Mikrotik RB95x devices) and 665bb2749906aff4d4ec607a308353fa30cb1b3a (ar71xx: fix invalid pointer dereference in rb95x_nand_scan_fixup()) to RB92x devices too. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* apm821xx: convert to device-tree board detectionChristian Lamparter2017-12-2110-81/+41
| | | | | | | | | | | | | This patch converts all apm821xx devices to the device-tree board-detection method. All instances of the legacy boardnames (mbl,mr24,...) are converted to "vendor,device" identifier. The custom board-detection code in apm821xx.sh is removed as it no longer serves any purpose. Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: enable metadata for packagingChristian Lamparter2017-12-213-93/+10
| | | | | | | | | | This patch enables metadata-supported image verification for all apm821xx supported devices. Since this method comes with a built-in image verification tool (fwtool), the previous image checks can be removed. Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: align device names with vendor_device formatChristian Lamparter2017-12-211-10/+10
| | | | | | | | | | Currently, the device name handle does not include the manufacturer. This can make it hard do differentiate between products from different vendors that have the same product name. As the handle is used to derive the image name. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: dts: rename devices dts files to include the manufacturerChristian Lamparter2017-12-216-5/+5
| | | | | | | | | | | This patch rename all the DT source files in order to match upstream's "manufacturer-device.dts" format. Please note that the DEVICE_DTB isn't changed. This is because the u-boot of the MyBook Live defines the fdt_file variable to be "apollo3g/apollo3g.dtb". Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: add product names to the dt compatible for MerakiChristian Lamparter2017-12-212-2/+2
| | | | | | | | | | Meraki choose to use their product's codename as the main compatible string. Mathias Kresin commented that this is a poor choice as this will confuse the users and devs once the device-tree compatible is used for board-detection and possible the image name. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: dts: append SoC compatible to DTSChristian Lamparter2017-12-214-2/+4
| | | | | | | | | | | | | | | | | | | | | This patch appends the "apm,bluestone" or "amcc,apollo3g" machine compatible string to the current device tree source. Please note that unlike other archs the PPC DT code does not regard the machine's compatible string as a priority list. This is explained in the kernel's usage-model.txt as follows: "PowerPC uses a slightly different scheme where it calls the .probe() hook from each machine_desc, and the first one returning TRUE is used. However, this approach does not take into account the priority of the compatible list, and probably should be avoided for new architecture support." For this reason, the "apm,bluestone" compatible string can't be added to the WNDR4700. As otherwise the target specific pci fix-up code will get ignored and this causes the ath9k WIFI to not get initialized. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: replace DEVICE_{PROFILE|NAME} with BOARD_NAMEChristian Lamparter2017-12-211-10/+6
| | | | | | | | | | | | | | | | | | | | | This patch sets the BOARD_NAME variable on each affected apm821xx device. The existing DEVICE_PROFILE and DEVICE_NAME assignments are deprecated as they no longer serve any purpose. The BOARD_NAME variable is used by the sysupgrade-tar method to specifiy a directory overwrite for the sysupgrade-$dir directory in the generated tar file. Keeping the original boardname in this context will be necessary for targets that utilize the sysupgrade-tar method. Otherwise, sysupgrade on an previous installation will not recognize the newly generated images. This step is necessary since an upcoming patch realigns the existing shortname for a device with a proper "manufacturer_device" identifier. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: replace whitespace with tabsChristian Lamparter2017-12-211-1/+1
| | | | Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: explicitly build the rootfs.img.gz targetChristian Lamparter2017-12-211-2/+2
| | | | | | | | | | | | | | | The commit 87b668765e1 ("image: when using the new image build code, gzip ext4 images by default") forced that all targets that select the ext4 as the root filesystem to always compress the generated rootfs. This is fine, but this method doesn't not allow to append the metadata on a per-target base. Therefore this patch changes the rootfs image production rule to generate the gzip step manually. This way the metadata can be appended at a later date. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ramips: fix devicetree compat stringsMathias Kresin2017-12-215-5/+5
| | | | | | | | | | | | "PandoraBox" is not the name of the manufacturer, it's a firmware made by the manufacturer actually. Their official English name is "D-Team". PBR-M1 is the only one they use "PandoraBox" as a brand name. Their other products are using "Newifi" as their trademark (including Y1 and Y1S which used to be OEM products for Lenovo). Signed-off-by: Chuanhong Guo <gch981213@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for newifi d2Jackson Ming Hu2017-12-216-0/+177
| | | | | | | | | | | | | | | | | | | | | | | | | | | Previously Newifi D2 could only use PandoraBox M1's firmware. It works fine, but LED GPIO is different. As a result, a separated DTS file for this device should be implemented. Hardware spec: * CPU: MTK MT7621A * RAM: 512MB * ROM: 32MB SPI Flash * WiFi: MTK MT7603+MT7612 * Button: 2 buttons (reset, wps) * LED: 3 single-color LEDs (USB, WiFi 2.4GHz, WiFi 5GHz) & 2 dual-color LEDs (Power, Internet) * Ethernet: 5 ports, 4 LAN + 1 WAN Installation method: Same as Newifi D1, users may need to request unlock code from the device manufacturer. Otherwise, a SPI flash programmer may be necessary to get the firmware flashed. After the device is unlocked, press and hold reset button before power cable plugs in. Then go to http://192.168.1.1 to upload and flash the firmware package. Signed-off-by: Jackson Ming Hu <huming2207@gmail.com>
* ramips: add support for Vonets VAR11N-300Andrew Crawley2017-12-215-1/+105
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The VAR11N-300 is a tiny wireless-N device with a hardwired Ethernet cable, one extra Ethernet port, and an internal antenna, based on the MediaTek MT7620n chipset. Specs: - MT7620n WiSoC @ 600MHz - 32 MB SDRAM - 4 MB SPI flash - 2T2R 2.4GHz WiFi-N - 1 attached 10/100 Ethernet cable (LAN) - 1 10/100 Ethernet port (WAN) - 1 attached USB / barrel 5vdc power cable - 5 LEDs (see notes below) - 1 reset button - 1 UART (3 pads on board) Installation: The stock firmware does not support uploading new firmware directly, only checking the manufacturer's site for updates. This process may be possible to spoof, but the update check uses some kind of homebrew encryption that I didn't investigate. Instead, you can install via a backdoor: 1. Set up a TFTP server to serve the firmware binary (lede-ramips-mt7620-var11n-300-squashfs-sysupgrade.bin) 2. Factory reset the device by holding the reset button for a few seconds. 3. Open the web interface (default IP: 192.168.253.254) 4. Log in with the "super admin" credentials: username `vonets`, password `vonets26642519`. 5. On the "Operative Status" page, click the text "System Uptime", then quickly click the uptime value. 6. If successful, an alert dialog will appear reading "Ated start", and the device will now accept telnet connections. If the alert does not appear, repeat step 5 until it works (the timing is a bit tricky). 7. Telnet to the device using credentials "admin / admin" 8. Retrieve the firmware binary from the tftp server: `tftp -l lede.bin -r lede-ramips-mt7620-var11n-300-squashfs-sysupgrade.bin -g <tftp-server-ip>` 9. Write the firmware to flash: `mtd_write write lede.bin /dev/mtd4` 10. Reboot Tested: - LAN / WAN ethernet - WiFi - LAN / WAN / status LED GPIOs (see notes below) - Reset button - Sysupgrade Notes: LEDs: The board has 5 LEDs - two green LEDs for LAN / WAN activity, one blue LED for WiFi, and a pair of "status" LEDs connected to the same GPIO (the blue LED lights when the GPIO is low, and the green when it's high). I was unable to determine how to operate the WiFi LED, as it does not appear to be controlled by a GPIO directly. Recovery: The default U-boot installation will only boot from flash due to a missing environment block. I generated a valid 4KB env block using U-boot's `fw_setenv` tool and wrote it to flash at 0x30000 using an external programmer. After this, it was possible to enter the U-boot commandline interface and download a new image via TFTP (`tftpboot 81b00000 <image-filename>`), but while I could boot this image sucessfully (`bootm`), writing it to flash (`cp.linux`) just corrupted the flash chip. The sysupgrade file can be written to flash at 0x50000 using an external programmer. Signed-off-by: Andrew Crawley <acrawley@gmail.com>
* ramips: add helper variable for boardnameMathias Kresin2017-12-212-224/+226
| | | | | | | | | | | | | Add a helper variable which contains the boardname separated from the vendor name. It allows to switch to a device tree compatible string based boardname, by keeping the $board:colour:function syntax in scripts handling/adding config for LEDs. Boards not using the device tree compatible string as based boardname are unaffected by the change, since none of them uses a comma in the boardname. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: sync image filename with boardnameMathias Kresin2017-12-213-4/+9
| | | | | | | | | | | | | Use <manufacturer>_<modelname> as image name for board using the devicetree compat string as boardname. Replace the underline of the device define, to keep the SUPPORTED_DEVICES in sync with a devicetree compat string based boardname. Override the default SUPPORTED_DEVICES for board which are having an userspace boardname with an underline. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fallback to generic board detectMathias Kresin2017-12-214-15/+7
| | | | | | | Fallback to the generic board detection if no case for the current board exists. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: drop LinkIt Smart 7688 Duo userspace supportMathias Kresin2017-12-214-13/+3
| | | | | | | | | | The LinkIt Smart 7688/LinkIt Smart 7688 Duo are identical beside the extra ATmega32U4 - accessible via UART - on the the Duo. Since all relevant hardware is identical, drop the Duo special handling in userspace. Signed-off-by: Mathias Kresin <dev@kresin.me>
* kernel: Update kernel 4.9 to 4.9.70Hauke Mehrtens2017-12-1930-262/+172
| | | | | | Runtime tested on lantiq. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ramips: fix polarity in gpio-export nodeMathias Kresin2017-12-1811-16/+11
| | | | | | | | If we need to set the initial output value to GPIOF_OUT_INIT_HIGH (1) to enable something, the pin is ACTIVE_HIGH. The same applies to GPIOF_OUT_INIT_LOW (0) and ACTIVE_LOW. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ar71xx: fix lan ports on ens202extMarty E. Plummer2017-12-181-0/+1
| | | | | | | | | In the stock firmware both eth0 and eth1 are set to br-lan, add this behavior to our images. Fixes: FS#1084 Signed-off-by: Marty E. Plummer <hanetzer@protonmail.com>
* brcm63xx: fix Sercomm AD1018 status ledJonas Gorski2017-12-171-1/+1
| | | | | | | | The status led part was missed when changing the board name to *-nor. Fixes: e12c72bb52eb ("brcm63xx: Add Sercomm AD1018 support") Reported-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com> Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* lantiq: sync image filename with boardnameMathias Kresin2017-12-162-185/+227
| | | | | | | | | | | | | Use <manufacturer>_<modelname> as image name. Use the BOARD_NAME variable to ensure that the former used boardname is still used as the subdirectory name for the sysupgrade-tar image, to not break sysupgrade from earlier versions. While at it, normalise the image filenames by using only lower case characters and bin as file extension for sysupgrade images. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: drop unused variable from image build codeMathias Kresin2017-12-161-3/+0
| | | | | | | Remove the DEVICE_PROFILE variable. The variable isn't used at all. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: use the generic board detectMathias Kresin2017-12-161-19/+0
| | | | | | | Drop the target specific detection function in favour of the generic one provided by base-files. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: add missing model namesMathias Kresin2017-12-161-0/+1
| | | | Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: remove the former board name from device tree modelMathias Kresin2017-12-1660-60/+60
| | | | | | | Remove the former used board name from the device model property and use the model name as it is. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: use the compatible string as board nameMathias Kresin2017-12-169-67/+131
| | | | | | | | | | | Use the first compatible string as board name in userspace. Add the new board name as well as the former used board name to the image metadata to keep compatibilty with already deployed installations. Don't add the former used boardname for boards which exists only in master or evaluation boards. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: drop SoC name from eval boards compatible stringMathias Kresin2017-12-1611-11/+11
| | | | | | Keep it in the same format as used for the other eval boards. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: add compatible strings to dts filesMathias Kresin2017-12-1653-0/+59
| | | | | | The compatible string is mandetory for devicetree source file. Signed-off-by: Mathias Kresin <dev@kresin.me>
* x86: Add support for kernel 4.14Hauke Mehrtens2017-12-169-16/+710
| | | | | | | | This adds basic support for kernel 4.14, this was tested in qemu only. The subtarget configuration was refresh with kernel 4.14 and the options needed to make it compile on kernel 4.9 were added manually. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: add kmod-crypto-ecdhHauke Mehrtens2017-12-162-0/+50
| | | | | | | | | | In kernel 4.14 kmod-bluetooth depends on kmod-crypto-ecdh, add kmod-crypto-ecdh to LEDE. Both packages also depend on the kmod-crypto-kpp package. To build this we have to fix the dependency of CRYPTO_ECDH which has a typo. This patch is already accepted upstream. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: generic: Add kernel 4.14 supportHauke Mehrtens2017-12-16131-8/+25622
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds initial support for kernel 4.14 based on the patches for kernel 4.9. In the configuration I deactivated some of the new possible security features like: CONFIG_REFCOUNT_FULL CONFIG_SLAB_FREELIST_HARDENED CONFIG_SOFTLOCKUP_DETECTOR CONFIG_WARN_ALL_UNSEEDED_RANDOM And these overlay FS options are also deactivated: CONFIG_OVERLAY_FS_INDEX CONFIG_OVERLAY_FS_REDIRECT_DIR I activated this: CONFIG_FORTIFY_SOURCE CONFIG_POSIX_TIMERS CONFIG_SLAB_MERGE_DEFAULT CONFIG_WATCHDOG_HANDLE_BOOT_ENABLED I am not sure if I did the porting correct for the following patches: target/linux/generic/backport-4.14/020-backport_netfilter_rtcache.patch target/linux/generic/hack-4.14/220-gc_sections.patch target/linux/generic/hack-4.14/321-powerpc_crtsavres_prereq.patch target/linux/generic/pending-4.14/305-mips_module_reloc.patch target/linux/generic/pending-4.14/611-netfilter_match_bypass_default_table.patch target/linux/generic/pending-4.14/680-NET-skip-GRO-for-foreign-MAC-addresses.patch Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* x86: refresh configurationHauke Mehrtens2017-12-163-16/+3
| | | | | | | Just refresh the kernel configuration, some options are removed because they are now in the generic kernel configuration. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: generic: add some more 4.9 configure optionsHauke Mehrtens2017-12-161-0/+9
| | | | | | | These are taken from the x86 target and should make support kernel 4.9 and 4.14 in the x86 target easier. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* x86: add on-chip thermal sensors and cpuid supportPhilip Prindeville2017-12-162-1/+33
| | | | | | | | | | | Cover temperature sensors for all mainstream 64-bit processors, including AMD 10h and 15h families, Intel iCore, Xeon, Atom, and Via Nano. Also add CPUID support for user-space applications to detect CPU type. Include the on-chip sensors for 64-bit CPU's in the generic profile in case someone builds a 32-bit kernel to run on a Xeon SoC, etc. Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
* x86: refresh settings for 4.9.59Philip Prindeville2017-12-161-7/+1
| | | | Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
* brcm63xx: backport mdio-bus reset gpio supportJonas Gorski2017-12-1613-96/+416
| | | | | | | Backport the mdio-bus reset gpio support from 4.12 and use it instead of toggling the reset ourself. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* brcm63xx: backport enet cleanup patchesJonas Gorski2017-12-1614-36/+415
| | | | | | Align with upstream version, mostly non-fixes and small clean ups. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* brcm63xx: register serial through device treeJonas Gorski2017-12-16167-363/+1144
| | | | | | | Register serial consoles through device tree instead of through board data. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* brcm63xx: add uart nodesJonas Gorski2017-12-1610-0/+224
| | | | | | | Now that we can register uarts through device-tree, add them to the dtsi files. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-24 18:54:29 +0000