aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
* ramips: Fix sdhci kernel panics on MT7621Andrew Yong2016-11-211-2/+2
| | | | | | | | | | | | | | Enable work-arounds present in the code commented-out but needed to write to sdcard on mt7621 which currently causes kernel to oops when engaging in serious writing to sdcard. With this change applied, there are still occasional warnings thrown by the mmc driver, however, at least it no longer crashes the system and even large writes (full-card dump/erase/write/compare) don't show any corruption. Signed-off-by: Daniel Golle <daniel@makrotopia.org> Rebase to LEDE and added "CONFIG_SOC_MT7621" check to ensure non-MT7621 devices do not face performance regressions. Signed-off-by: Andrew Yong <me@ndoo.sg>
* mvebu: Add BQL patch for mvneta driver.Toke Høiland-Jørgensen2016-11-211-0/+83
| | | | | | | | This adds the patch submitted to upstream that adds BQL to the mvneta driver: https://patchwork.kernel.org/patch/9328413/. Helps latency under load when the physical link is saturated. Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
* lantiq: use dwc2 by default on danubeBen Mulvihill2016-11-211-13/+13
| | | | | | Use dwc2 by default on all danube boards. Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
* lantiq: dwc2 parameters for danubeBen Mulvihill2016-11-211-2/+31
| | | | | | | | | | Parameters for dwc2 on lantiq. A separate dwc2_core_params structure is defined for danube because danube fifo sizes are large enough to be autodetected. This is not the case on arx and vrx. Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
* lantiq: device tree bindings for dwc2 on danubeBen Mulvihill2016-11-211-1/+2
| | | | | | | | | Device tree binding for dwc2 usb driver on danube. Leave old ifxhcd-danube driver as an alternative. Also adds dr_mode = "host" to eliminate warning on boot. Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
* lantiq: initialise dwc2 on danubeBen Mulvihill2016-11-211-0/+10
| | | | | | Initialise dwc2 usb driver on danube boards as well as ar9 and vr9. Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
* apm821xx: Add support for the Cisco Meraki MX60/MX60WChris Blake2016-11-2111-16/+283
| | | | | | | | | | | | | | | | | | | This patch adds support for the Cisco Meraki MX60/MX60W Security Appliance. Flashing information can be found at https://github.com/riptidewave93/LEDE-MX60 Specs are as follows: AppliedMicro APM82181 SoC at 800MHz 1GiB NAND - Samsung K9K8G08U0D 512MB DDR RAM - 4x Nanya NT5TU128M8GE-AC Atheros AR8327-BL1A Gigabit Ethernet Switch 1x USB 2.0 Port More info can be found at https://wiki.openwrt.org/toh/meraki/mx60 Cc: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
* ramips: add support for WeVO W2914NS v2perillamint2016-11-218-0/+168
| | | | Signed-off-by: Yong-hyu Ban <perillamint@gentoo.moe>
* ar71xx: Fix switch config on Mikrotik RB450/GJoão Chaínho2016-11-211-2/+6
| | | | | | | This patch fixes the ethernet switch initial config for Mikrotik RB450 and RB450G. The previous version wrongly changed the RouterStation Pro config. This one creates a specific config for the RB450G and leaves the RouterStation Pro unchanged. Signed-off-by: João Chaínho <joaochainho@gmail.com>
* ar71xx: add support for YunCore CPE830Piotr Dymacz2016-11-2110-26/+131
| | | | | | | | | CPE830 is a clone of AP90Q, with different type of antenna (panel) and additional 4 LEDs for WiFi signal level indication. Use the same flash approach as for YunCore AP90Q. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for YunCore CPE870Piotr Dymacz2016-11-2110-0/+188
| | | | | | | | | | | | | | | | | | | | | | | | | | YunCore CPE870 is an outdoor CPE/AP based on Atheros AR9341. Short specification: - 535/400/200 MHz (CPU/DDR/AHB) - 2x 10/100 Mbps Ethernet, passive PoE support - 64/128 MB of RAM (DDR2) - 8 MB of FLASH - 2T2R 2.4 GHz with external PA (SKY65174-21), up to 30 dBm - internal 14 dBi panel antenna - 8x LED, 1x button - UART (JP1) header on PCB Flash instruction (do it under U-Boot, using UART): 1. tftp 0x80060000 lede-ar71xx-generic-cpe870-squashfs-sysupgrade.bin 2. erase 0x9f020000 +$filesize 3. cp.b $fileaddr 0x9f020000 $filesize 4. setenv bootcmd "bootm 0x9f020000" 5. saveenv && reset Vendor firmware access (login/password): Admin/5up Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for YunCore AP90QPiotr Dymacz2016-11-2110-7/+163
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | YunCore AP90Q is an outdoor CPE/AP based on Qualcomm/Atheros QCA9531 v2. Short specification: - 650/600/216 MHz (CPU/DDR/AHB) - 2x 10/100 Mbps Ethernet, passive PoE support - 64/128 MB of RAM (DDR2) - 16 MB of FLASH - 2T2R 2.4 GHz with external PA, up to 29 dBm - 2x internal 5 dBi omni antennas - 4x LED, 1x button - UART (JP1) header on PCB Flash instruction under U-Boot, using UART: 1. tftp 0x80060000 lede-ar71xx-generic-ap90q-squashfs-sysupgrade 2. erase 0x9f050000 +$filesize 3. cp.b $fileaddr 0x9f050000 $filesize 4. setenv bootcmd "bootm 0x9f050000" 5. saveenv && reset Flash instruction under vendor fimrware, using telnet/SSH: 1. Connect PC with 192.168.1.x address to WAN port 2. Power up device, enter failsafe mode with button (no LED indicator!) 3. Change root password and reboot (mount_root, passwd ..., reboot -f) 4. Upload lede-ar71xx-generic-ap90q-squashfs-sysupgrade.bin to /tmp using SCP 5. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253 6. Invoke: - cd /tmp - fw_setenv bootcmd "bootm 0x9f050000" - mtd erase firmware - mtd -r write lede-ar71xx-generic-ap90q-squashfs-sysupgrade.bin firmware Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for COMFAST CF-E380AC v1 and v2Piotr Dymacz2016-11-2112-9/+211
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | COMFAST CF-E380AC v1/v2 is a ceiling mount AP with PoE support, based on Qualcomm/Atheros QCA9558+QCA9880+AR8035. There are two versions of this model, with different RAM and U-Boot mtd partition sizes: - v1: 128 MB of RAM, 128 KB U-Boot image size - v2: 256 MB of RAM, 256 KB U-Boot image size Version number is available only inside vendor GUI, hardware and markings are the same. Short specification: - 720/600/200 MHz (CPU/DDR/AHB) - 1x 10/100/1000 Mbps Ethernet, with PoE support - 128 or 256 MB of RAM (DDR2) - 16 MB of FLASH - 3T3R 2.4 GHz, with external PA (SE2576L), up to 28 dBm - 3T3R 5 GHz, with external PA (SE5003L1), up to 30 dBm - 6x internal antennas - 1x RGB LED, 1x button - UART (T11), LEDs/GPIO (J7) and USB (T12) headers on PCB - external watchdog (Pericon Technology PT7A7514) Flash instruction: Original firmware is based on OpenWrt. Use sysupgrade image directly in vendor GUI. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for COMFAST CF-E320N v2 and CF-E520N/CF-E530NPiotr Dymacz2016-11-2110-42/+329
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | As we already have support for CF-E316N v2 and many devices from this vendor look similar, the support was included in existing mach-*.c file, with few cleanups and fixes. All 3 devices are based on Qualcomm/Atheros QCA9531 v2. COMFAST CF-E320N v2 is a ceiling mount AP with PoE support. Short specification: - 650/393/216 MHz (CPU/DDR/AHB) - 2x 10/100 Mbps Ethernet, both with PoE support - 64 MB of RAM (DDR2) - 16 MB of FLASH - 2T2R 2.4 GHz, up to 22 dBm - 2x internal antennas - 1x RGB LED, 1x button - UART (J1), GPIO (J9) and USB (J2) headers on PCB - external watchdog (Pericon Technology PT7A7514) COMFAST CF-E520N/CF-E530N are in-wall APs with USB and PoE support. They seem to have different only the front panel. Short specification: - 650/393/216 MHz (CPU/DDR/AHB) - 2x 10/100 Mbps Ethernet, WAN with PoE support - 1x USB 2.0 (in CF-E520N covered by panel, available on PCB) - 32 MB of RAM (DDR2) - 8 MB of FLASH - 2T2R 2.4 GHz, up to 22 dBm - 2x internal antennas - 1x LED, 1x button - UART (J1) headers on PCB Flash instruction: Original firmware is based on OpenWrt. Use sysupgrade image directly in vendor GUI. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ipq806x: c2600: change wan and lan led trigger to swconfig portHenryk Heisig2016-11-211-2/+2
| | | | Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ipq806x: enable swconfig LED supportHenryk Heisig2016-11-211-0/+1
| | | | Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* kernel: remove pipetypes unused var warningKevin Darbyshire-Bryant2016-11-211-1/+11
| | | | | | | Update patch to remove pipetypes var declaration which was throwing unused variable warning due to the original patch removing the only use. Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
* ipq806x: switch to upstream usb driver and backport fixesPavel Kubelun2016-11-2118-23/+1094
| | | | | | Also removing fifo-resize property drom DT as it has been removed from the driver. Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* ar71xx: fix drivers/mtd/nand/ar934x_nfc.cPaul Wassi2016-11-181-8/+2
| | | | | | | Fix the incorrect usage of ar934x_nfc_write_page and ar934x_nfc_write_page_raw. Add *page* in the argument list and remove the local variable. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* lantiq: remove device specific sysupgrade image checksFelix Fietkau2016-11-201-22/+1
| | | | | | Replaced by image metadata Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ipq806x: remove device specific sysupgrade image checksFelix Fietkau2016-11-201-24/+1
| | | | | | Replaced by image metadata Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: add bcm47xxpart patch fixing parsing with some TRX formatsRafał Miłecki2016-11-201-0/+37
| | | | | | | | This fixes parsing partition placed after TRX with block-aligned length. It's important e.g. for Archer C9 which has TRX with kernel only and rootfs as separated partition. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ipq806x: fix build errorsPavel Kubelun2016-11-193-0/+262
| | | | | | Add missing patches that broke LEDE builder while updating WDT driver Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* kernel: rtl8367(b): fix build errorMathias Kresin2016-11-192-2/+2
| | | | | | | | | | Fix build on targets not using CONFIG_MODULE_STRIPPED. Neither RTL8367_DRIVER_DESC nor RTL8367B_DRIVER_DESC are defined anywhere. It worked for targets using CONFIG_MODULE_STRIPPED since our module stripper no-ops the various module info macros. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: run append-metadata before check-size to fix build errorsFelix Fietkau2016-11-191-4/+4
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* x86: fix GRUB_ROOT for Xen subtargetWilfried Klaebe2016-11-192-1/+7
| | | | | | | | | Change grub's root device to xen/xvda,msdos1 for the x86_xen_domu target so that it will boot without further changes. Signed-off-by: Wilfried Klaebe <w+lede-project@chaos.in-kiel.de> [Jo-Philipp Wich: fixed and rebased patch from FS#264, added subject] Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ramips: append metadata to imagesFelix Fietkau2016-11-197-22/+33
| | | | | | | metadata checks are not enforced yet, because some images are still being built by legacy code Signed-off-by: Felix Fietkau <nbd@nbd.name>
* lantiq: append metadata to imagesFelix Fietkau2016-11-192-5/+7
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ipq806x: append metadata to imagesFelix Fietkau2016-11-192-6/+6
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* bcm53xx: build image for TP-LINK Archer C9 v1Rafał Miłecki2016-11-192-1/+27
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: support SafeLoader format in sysupgradeRafał Miłecki2016-11-192-2/+36
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: add kernel support for TP-LINK Archer C9 V1Rafał Miłecki2016-11-193-42/+194
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ar71xx: enable serial console on mikrotik devicesJoão Chaínho2016-11-181-1/+4
| | | | | | | This patch enables the serial console on some Mikrotik devices (RB450, RB450G, RB493G, RB750UP). Signed-off-by: João Chaínho <joaochainho@gmail.com>
* ramips: add support for ZyXEL Keenetic VivaVitaly Chekryzhev2016-11-187-0/+184
| | | | | | | | | Factory image can be installed via Zyxel WebUI. Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com> [removed linux,modalias parameter from flash node in dts] [removed sdhci node from dts; no sd card slot here] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add MT7620 MIB support for switch and portVitaly Chekryzhev2016-11-172-72/+351
| | | | | | | | | Move definitions to header. Replace array size definitions with macro. Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com> [merged into 0513-net-mediatek-add-swconfig-driver-for-gsw_mt762x.patch] Signed-off-by: Mathias Kresin <dev@kresin.me> Acked-by: John Crispin <john@phrozen.org>
* ipq806x: refresh patchesHannu Nyman2016-11-1714-50/+25
| | | | | | | | | | This patch refreshes the ipq806x kernel patches. There was a large PR for ipq806x in the queue when the kernel patches were refreshed for 4.4.32, so currently there is quite much fuzz for ipq806x. Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* ramips: add support for Sitecom WLR-6000Jasper Scholte2016-11-176-1/+211
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Sitecom firmware upgrade file has SENAO_FIRMWARE_TYPE 2 set. This looks rather wrong since SENAO_FIRMWARE_TYPE 2 is kernel only but the file is way to big for only including a kernel. The factory image need to have the dlf file extension. Otherwise the Sitecom firmware rejects the file. The stock firmware uses the following mac addresses: LAN: 00:0C:F6:AA:BB:D8 (u-boot env: ethaddr) 2,4: 00:0C:F6:AA:BB:D8 (EEPROM) 5: 00:0C:F6:AA:BB:DC (EEPROM) WAN: 00:0C:F6:AA:C8:43 (u-boot env: wanaddr) Assuming the mac address range :D8 to :DC is reserved for this device, the MAC addresses were reorder to have a unique MAC address for each interface: 2.4GHz: 00:0C:F6:AA:BB:D8 LAN: 00:0C:F6:AA:BB:D9 WAN: 00:0C:F6:AA:BB:DA 5 GHz: 00:0C:F6:AA:BB:DC The first MAC is assigned to the 2.4GHz WiFi interface to keep compatibility with the SSIDs printed on the case, which have the last three sextets of the MAC address appended. There are still issues with the rt2x00 driver. It is not possible to use both wireless interfaces at the same time. The 2.4 GHz wireless (PCIe) only works if the internal 5GHz wireless is/has been enabled or used for scanning. The internal 5GHz wireless only works if the 2.4GHz wireless (PCIe) was never enabled. Disabling the 2.4Ghz after it was enabled will result in stations seeing the 5Ghz AP but are unable to connect. Due to the not optimal working wifi the manufacture, backup and storage partitions of the OEM firmware are kept for now to allow an easy switch back to the Sitecom firmware. Signed-off-by: Jasper Scholte <NightNL@outlook.com> Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for Digineo AC1200 ProDominik Menke2016-11-176-4/+33
| | | | | | This is basically a ZBT-WG3526 (mt7621 SoC), but with 32M flash. Signed-off-by: Dominik Menke <dom@digineo.de>
* ramips: cleanup ZBT-WG3526.dtsiDominik Menke2016-11-171-6/+6
| | | | | | | | - replace magic numbers with GPIO_* constants - replace generic PCI definitions with correct vendor and device identification Signed-off-by: Dominik Menke <dom@digineo.de>
* ramips: split ZBT-WG3526.dts into dtsi and dts filesDominik Menke2016-11-172-112/+120
| | | | Signed-off-by: Dominik Menke <dom@digineo.de>
* kernel: enable pcryptJason A. Donenfeld2016-11-163-3/+3
| | | | | | | | | This is a powerful API for parallel crypto from which many other modules can benefit. It only winds up being turned on on SMP systems, which means this adds 0 bytes to the kernel on tiny machines, while only adding a small bit to SMP systems for big performance improvements. Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
* octeon: fix feature flag for initramfs supportFelix Fietkau2016-11-161-1/+1
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: update kernel 4.4 to version 4.4.32Stijn Tintel2016-11-1612-82/+68
| | | | | | | | Refresh patches for all targets that support kernel 4.4. Compile-tested on all targets that use kernel 4.4 and aren't marked broken. Runtime-tested on ar71xx, octeon. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* ar71xx: tl-wpa8630: Use dynamic parsing of the firmware partitionHenryk Heisig2016-11-163-4/+8
| | | | Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ipq806x: fixes for R7800 and C2600Pavel Kubelun2016-11-164-18/+115
| | | | | | | | Updating spi pins configuration in R7800 and C2600 DTs Adding more usb power pin export and gsbi6 in R7800 DT Updating and fixing leds Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* ipq806x: fix Netgear R7500v2 memoryPavel Kubelun2016-11-161-1/+6
| | | | | | Netgear R7500v2 has 512MB of RAM with 2MB reserved block in the end of memory region. Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* ipq806x: fix pci pinsPavel Kubelun2016-11-162-7/+9
| | | | | | Fix pci pins drive-strength according to oem sources. Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* ipq806x: add vlans during switch init into R7800 DTPavel Kubelun2016-11-161-0/+4
| | | | Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* ipq806x: add support for RPM message RAMPavel Kubelun2016-11-164-0/+150
| | | | Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* ipq806x: add support for RPM clock controllerdissent12016-11-167-0/+1645
| | | | | | The patch #179 for RPM has initially been made for apq806x board. It has been modified to support ipq806x instead of apq8064. Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-05 12:38:27 +0000