aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
* kernel: bump 4.14 to 4.14.53Koen Vandeputte2018-07-044-11/+11
| | | | | | | | | Refreshed all patches Compile-tested on: cns3xxx, imx6, x86_64 Runtime-tested on: cns3xxx, imx6, x86_64 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.111Koen Vandeputte2018-07-044-6/+6
| | | | | | | | | Refreshed all patches Compile-tested on: ar71xx Runtime-tested on: ar71xx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: remove bs-partition ro-flag for UniFi AC devicesChristoph Krapp2018-07-041-1/+0
| | | | | | | | | | | | This removes the read-only flag from the bs (bootselect) partition on UniFi AC devices. This allows to correct the indicator from which partition the device is booting its kernel from. See also: - freifunk-gluon/gluon#1301 - https://bugs.lede-project.org/index.php?do=details&task_id=662 Signed-off-by: Christoph Krapp <achterin@googlemail.com>
* ath79: swap TP-Link Archer C7 v2 USB port LED and GPIO namesAleksandr V. Piskunov2018-07-041-6/+6
| | | | | | | | | TP-Link Archer C7 v2 USB port LED and GPIO names are in incorrect order, i.e. in order to match actual user visible labels, usb1 should be usb2, and vice versa. This patch swaps LED and GPIO power control node names. Signed-off-by: Aleksandr V. Piskunov <aleksandr.v.piskunov@gmail.com>
* ath79: drop mv88e6063 switch driverMathias Kresin2018-07-041-289/+0
| | | | | | | | Due do a missing KCONFIG isn't selectable nor enabled in the target kernel config. Drop it for now and enable/add the driver at the time it is required. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ipq806x: fix numbering for Netgear R7800 LAN portsAleksandr V. Piskunov2018-07-041-5/+5
| | | | | | | | | | Netgear R7800 switch LAN ports are numbered backwards in LuCI, i.e. numbering is not corresponding to the actual physical port labels, patch fixes that. Signed-off-by: Aleksandr V. Piskunov <aleksandr.v.piskunov@gmail.com> [merged with existing board using the same config] Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* ramips: add support for TL-WA801ND v5Romain MARIADASSOU2018-07-046-0/+77
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - System-On-Chip: MediaTek MT7628NN - CPU/Speed: 580 MHz - Flash-Chip: ELM Technology GD25Q64 - Flash size: 8192 KiB - RAM: 64 MiB - Wireless No1: SoC-integrated: MT7628N 2.4GHz 802.11bgn Currently the only method to install openwrt for the first time is via TFTP recovery. After first install you can use regular updates. Flash instructions: 1) To flash the recovery image, start a TFTP server with IP address 192.168.0.66 and serve the recovery image named tp_recovery.bin. 2) Connect your device to the LAN port, then press the WPS and Reset button and power it up. Keep pressing the WPS/Reset button for 10 seconds or until the lock LED is lighting up. It will try to download the recovery image and flash it. It can take up to 2-3 minutes to finish. When it reaches 100%, the router will reboot itself. Signed-off-by: Romain MARIADASSOU <roms2000@free.fr>
* ramips: add support for ZyXEL Keenetic Extra IIMaxim Anisimov2018-07-046-2/+228
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - System-On-Chip: MT7628N/N - CPU/Speed: 580 MHz - Flash-Chip: Winbond w25q256 - Flash size: 32768 KiB - RAM: 128 MiB - 5x 10/100 Mbps Ethernet - 4x external, non-detachable antennas - UART (J1) header on PCB (57600 8n1) - Wireless No1 (2T2R): SoC-integrated: MT7628N 2.4GHz 802.11bgn - Wireless No2 (2T2R): On-board chip: MT7612EN 5GHz 802.11ac - USB: Yes 1 x 2.0 - 4x LED, 3x button The device supports dual boot mode. So we use only first half of flash. Flash instruction: The only way to flash OpenWrt image is to use tftp recovery mode in U-Boot: 1. Configure PC with static IP 192.168.1.2/24 and tftp server. 2. Rename "openwrt-ramips-mt76x8-zyxel_keenetic-extra-ii-squashfs-factory.bin" to "kextra2_recovery.bin" and place it in tftp server directory. 3. Connect PC with one of LAN ports, press the reset button, power up the router and keep button pressed until power led start blinking. 4. Router will download file from server, write it to flash and reboot. Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
* ramips: move zyimage define to common MakefileMaxim Anisimov2018-07-042-4/+4
| | | | Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
* ramips: add support for MikroTik RouterBOARD RBM11gTobias Schramm2018-07-046-1/+157
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the MikroTik RouterBOARD RBM11g. =Hardware= The RBM11g is a mt7621 based device featuring one GbE port and one miniPCIe slot with a sim card socket and USB 2.0. ==Switch== The single onboard Ethernet port is connected the CPU directly. The internal switch of the mt7621 SoC is disabled. ==Flash== The device has one spi nor flash chip. It is a 128 Mbit winbond 25Q128FVS connected to CS0. ==PCIe== The board features a single miniPCIe slot. It has a dedicated mini SIM socket and a USB 2.0 port. Power to the miniPCIe slot is controlled via GPIO9. ==USB== There are no external USB ports. ==Power== The board can accept both, passive PoE and external power via a 2.1 mm barrel jack (center-positive). The input voltage range is 11-32 V. ==Serial port== The device does have an onboard UART on an unpopulated header next to the flash chip: GND: pin 2 TX: pin 7 RX: pin 6 Settings: 115200, 8N1 See below illustration for positioning of the header. 0 = screw hole * = some pin T = TX pin R = RX pin G = GND pin Pinout: +--------------- |O | __ | / \ | \__/ | | | | +---+ | |RAM| | +--+ | | | |**| <- unpopulated header with UART | |*T| +---+ | |R*| +--------+ | |**| | | | |G*| | CPU | | +--+ | | | +--+ | | | | | +--------+ | +--+ <- flash chip |O | +-----+ | | | |+--+ | | || | | | +--------------------- =Installation= To install an OpenWRT image to the device two components must be built: 1. A openwrt initramfs image 2. A openwrt sysupgrade image ===initramfs & sysupgrade image=== Select target devices "Mikrotik RBM11G" in openwrt menuconfig and build the images. This will create the images "openwrt-ramips-mt7621-mikrotik_rbm11g-initramfs-kernel.bin" and "openwrt-ramips-mt7621-mikrotik_rbm11g-squashfs-sysupgrade.bin" in the output directory. ==Installing== **Make sure to back up your RouterOS license in case you do ever want to go back to RouterOS using "/system license output" and back up the created license file.** When rebooted the board will try booting via ethernet first. If your board does not boot via ethernet automatically you will have to attach to the serial port and set ethernet as boot device within RouterBOOT. 1. Set up a dhcp server that points the bootfile to tftp server serving the "openwrt-ramips-mt7621-mikrotik_rbm11g-initramfs-kernel.bin" initramfs image 2. Connect to ethernet port on board 3. Power on the board 4. Wait for OpenWrt to boot Right now OpenWrt will be running with a SSH server listening. Now OpenWrt must be flashed to the devices flash: 1. Copy "openwrt-ramips-mt7621-mikrotik_rbm11g-squashfs-sysupgrade.bin" to the device using scp. 2. Write openwrt to flash using "sysupgrade openwrt-ramips-mt7621-mikrotik_rbm11g-squashfs-sysupgrade.bin" Once the flashing completes the board will reboot. Disconnect from the devices ethernet port or stop the DHCP/TFTP server to prevent the device from booting via ethernet again. The device should now boot straight to OpenWrt. Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
* lantiq: enlarge AVM Fritz!Box 3370 flashMichael Kuron2018-07-042-36/+2
| | | | | | | | | | | | | | | | | | | | | | | | | Increase the available flash memory size in AVM Fritz!Box 3370 by incorporating the unused extra partitions located after the ubi partition. Note that users upgrading from a previous OpenWRT version need to re-install from the boot loader to pick up the new partition layout. Available flash space for rootfs+overlay increases from 48MB to 124MB. Reverting to the OEM firmware is still possible (via the recovery utility provided by AVM) as the OEM firmware appears to reformat the config and nand-filesystem partitions upon first boot if necessary. The reserved-kernel and reserved-filesystem partitions are overwritten by the OEM firmware when installing an update, so their contents do not matter. Boot loader and device-specific information (MAC addresses, calibration data, etc.) are not located in NAND flash and remain unharmed by this changed. Tested with OEM firmware 06.54 on device with HWRevision 5 and Micron flash chip. Signed-off-by: Michael Kuron <m.kuron@gmx.de>
* lantiq: backport stp-xway get callback implementationMathias Kresin2018-07-041-0/+47
| | | | | | | | | | | To keep the status of a LED connected to the stp during boot, the get callback is required. If the callback is missing and the LED default state is set to keep in the devicetree, the gpio led driver errors out during load. Fixes: FS#1620 Signed-off-by: Mathias Kresin <dev@kresin.me>
* kernel: fix AT8032 PHY phy id maskMathias Kresin2018-07-043-13/+16
| | | | | | | | | | | | Don't mask bit 4 of the AT8022 phy id. If bit 4 of the AT8022 phy id (0x004dd023) is masked, it will match the phy id of the AR8327 switch (0x004dd033) as well. It results in applied at803x driver settings/callbacks, which will at least limit the AR8327 phys to 100MBit operation instead of the possible 1000MBit. Signed-off-by: Mathias Kresin <dev@kresin.me>
* kernel: gen_stats: Fix netlink stats dumping in the presence of paddingKevin Darbyshire-Bryant2018-07-032-0/+98
| | | | | | | | | | | | | | | | | | | | | | | | Backport hot off the press upstream netlink patch. Fixes stats display from CAKE qdisc on MIPS allowing us to bump CAKE to latest version. The gen_stats facility will add a header for the toplevel nlattr of type TCA_STATS2 that contains all stats added by qdisc callbacks. A reference to this header is stored in the gnet_dump struct, and when all the per-qdisc callbacks have finished adding their stats, the length of the containing header will be adjusted to the right value. However, on architectures that need padding (i.e., that don't set CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS), the padding nlattr is added before the stats, which means that the stored pointer will point to the padding, and so when the header is fixed up, the result is just a very big padding nlattr. Because most qdiscs also supply the legacy TCA_STATS struct, this problem has been mostly invisible, but we exposed it with the netlink attribute-based statistics in CAKE. Fix the issue by fixing up the stored pointer if it points to a padding nlattr. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* ramips: limit dictionary size for lzma compressionFelix Fietkau2018-07-031-1/+1
| | | | | | | | | | | | In some cases, recent builds fail to boot from flash with at least some MT7621 based devices. The error message is: "LZMA ERROR 1 - must RESET board to recover" Booting the same kernel via TFTP works for some reason. Through testing I figured out that limiting the LZMA dictionary size seems to prevent these errors Signed-off-by: Felix Fietkau <nbd@nbd.name>
* zynq: remove config options handled by genericLuis Araneda2018-07-021-7/+0
| | | | | | | The options are now handled for all targets by the generic configuration Signed-off-by: Luis Araneda <luaraneda@gmail.com>
* ath79: add support for TP-Link RE450 v2Peter Lundkvist2018-07-026-1/+223
| | | | | | | | | | | | | | | | | | | | | | | | TP-Link RE450 v2 is a dual band router/range-extender based on Qualcomm/Atheros QCA9563 + QCA9880. Specification: - 775 MHz CPU - 64 MB of RAM (DDR2) - 8 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 3T3R 5 GHz - 1x 10/100/1000 Mbps Ethernet (AR8033 PHY) - 7x LED, 4x button - UART header on PCB (needs unmounted R64 & R69 0201 resistors/jumpers) Flash instruction: Apply factory image in OEM firmware web-gui. U-Boot does not seem to have any recovery functions, so debricking requires connection via UART. Signed-off-by: Peter Lundkvist <peter.lundkvist@gmail.com>
* kernel: bump 4.14 to 4.14.52Koen Vandeputte2018-07-029-56/+28
| | | | | | | | | Refreshed all patches Compile-tested on: cns3xxx, imx6, x86_64 Runtime-tested on: cns3xxx, imx6, x86_64 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.110Koen Vandeputte2018-07-024-16/+16
| | | | | | | | | Refreshed all patches Compile-tested on: ar71xx Runtime-tested on: ar71xx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: port TP-Link TL-WR741ND v4 and TL-WR740ND v4Rocco Folino2018-07-026-0/+224
| | | | | | | | | | This patch ports the TP-Link TL-WR741ND v4 and TL-WR740ND v4 to the ath79 target. Because the two devices share the same hw layout, this patch adds a common .dtsi which is included by the two .dts. Signed-off-by: Rocco Folino <rocco@folino.io>
* ath79: add pinmux to ar9330Rocco Folino2018-07-021-0/+18
| | | | | | | This patch adds the pinmux support to the ar9330 used to disable the JTAG or to enable switch LEDs Signed-off-by: Rocco Folino <rocco@folino.io>
* ramips: fix wizfi630a swapped lan/wan portLev2018-07-021-1/+1
| | | | | | | The order of the Ethernet ports were mixed up. This commit fixes the order to be aligned with the physical layout. Signed-off-by: Lev <leventelist@gmail.com>
* ath79: add support for Unifi AC MeshAdrian Schmutzler2018-06-286-19/+40
| | | | | | | | | The Unifi AC Mesh is equivalent to the Unifi AC Lite. However, for setting certain parameters with the flashed device it is helpful that the devices know their variant (e.g. automatically setting antenna gain for the different antennas in Lite and Mesh). Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for more AR7241 TP-Link boardsDmytro Smyrnov2018-06-288-0/+266
| | | | | | | | | | | Its common AP99(AR7241) platform with following devices: TP-Link TL-WR841N/ND v7 (SoC AR7241 / Wifi AR9287 / without USB) TP-Link TL-MR3220 v1 (SoC AR7241 / Wifi AR9285 / USB support) TP-Link TL-MR3420 v1 (SoC AR7241 / Wifi AR9287 / USB support) Signed-off-by: Dmytro Smyrnov <dioptimizer@hotmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: small wr1043nd-v4 fixesLucian Cristian2018-06-284-23/+36
| | | | | | | | | | | | | | | - fix sysupgrade check - move usb to v4 dts because v5 doesn't have it - make wan mac address behave like ar71xx target - add orange wan led support, it can be userspace activated like: on: echo default-on > /sys/class/leds/tp-link\:orange\:wan/trigger off: echo none > /sys/class/leds/tp-link\:orange\:wan/trigger Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* ath79: add support for Ubiquiti UniFi AC-ProLucian Cristian2018-06-286-126/+178
| | | | | | | | rework the dts to a common unifi-ac dtsi pro network is connected via phy0 and has usb ports lite network is connected via phy4 without usb ports Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* ath79: sync naming of Ubiquiti devicesAdrian Schmutzler2018-06-284-7/+8
| | | | | | | Use a Unifi AC Lite board-/image name consistent with other Ubiquiti devices. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Remove all memory nodes defined in dtsChuanhong Guo2018-06-2824-120/+0
| | | | | | | This target can automatically detect the correct memory size and we've been using it for long in ar71xx. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* treewide: gpio-export: add error handlingMathias Kresin2018-06-283-3/+9
| | | | | | | | Check if the GPIO is valid (or set at all). If no GPIO is set in the devicetree, a gpiolib related kernel warning + stacktrace is shown during boot and gpio-export reports GPIOs as exported albeit none really is. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ipq806x: drop gpio export patchMathias Kresin2018-06-281-166/+0
| | | | | | The hack isn't used by any board. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ipq806x: switch the NBG6817 wlan LEDs from amber to whiteStefan Lippers-Hollmann2018-06-281-2/+0
| | | | | | | | | | | | | | | | | The original device support patch configured the amber wlan LEDs (which are meant as error indicator by the OEM) controlled by the SOC's GPIO as wlan traffic indicators, as the correct white wlan LEDs are connected to GPIOs controlled by the QCA9984/ ath10k wlan cards were not accessible. The recent addition of GPIO/ LED support to ath10k now makes it possible to use the correct white LEDs instead - and "mac80211: ath10k: use tpt LED trigger by default" also enables them by default. While both LEDs are independent of each other (two separate LEDs sharing one light tunnel), triggering both on wlan traffic is not the intended behaviour (bright yellow light). Tested on the ZyXEL NBG6817. Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
* ramips: move mt7620n i2c_pins definition to right placeAndrey Jr. Melnikov2018-06-281-7/+7
| | | | | | | | | | Move to i2c pins pinmux node to the pinctrl node. Fixes: a0685deec458 ("ramips: Add i2c support for mt7620n") Signed-off-by: Andrey Jr. Melnikov <temnota.am@gmail.com> [fix commit message] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ipq806x: remove "firmware" partition definition from netgear routersHannu Nyman2018-06-274-20/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Remove the "firmware" partition definition from the DTS of R7800 to fix sysupgrade. Commit 4645a6d3 defined CONFIG_MTD_SPLIT_UIMAGE_FW=y for ipq806x and that causes mtd to misbehave as additional kernel and ubi partitions are detected from inside the "firmware" partition. [ 1.111324] 0x000001480000-0x000001880000 : "kernel" [ 1.121005] 0x000001880000-0x000007900000 : "ubi" [ 1.283912] 0x000007900000-0x000008000000 : "reserve" [ 1.296407] 0x000001480000-0x000007900000 : "firmware" [ 1.468043] no rootfs found after FIT image in "firmware" [ 2.426860] 2 uimage-fw partitions found on MTD device firmware [ 2.426931] 0x000001480000-0x000001880000 : "kernel" [ 2.440420] 0x000001880000-0x000007900000 : "ubi" Both kernel and ubi are already defined in DTS, so this duplication leads into errors in sysupgrade: Writing from <stdin> to kernel ... ubiattach: error!: strtoul: unable to parse the number '6 mtd10' ubiattach: error!: bad MTD device number: "6 mtd10" The partition is defined to same area as kernel+ubi, and is not needed for sysupgrade anymore. Remove it to fix things. Only tested for the R7800 but all of them should behave equal. Fixes: FS#1617 Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi> [squashed commits, add "tested on" note] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add switch port index for I-O DATA WN-GX300GRINAGAKI Hiroshi2018-06-271-2/+2
| | | | | | | | | | | WN-GX300GR has 5x RJ45 ports (port 0-4), and these ports are orderd on the device as follows: 4 3 2 1 0 1-4: lan 0: wan Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* firmware-utils: tplink-safeloader: switch tl-wr1043nd-v4 to dynamic partitionsLucian Cristian2018-06-272-3/+3
| | | | | | | Use the new dynamic partition split in tplink-safeloader so we no longer have to worry about kernel size increases. Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* ipq40xx: add support for the ZyXEL NBG6617Christian Lamparter2018-06-2610-1/+462
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for ZyXEL NBG6617 Hardware highlights: SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB DDR3L-1600/1866 Nanya NT5CC128M16IP-DI @ 537 MHz NOR: 32 MiB Macronix MX25L25635F ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN) USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC) WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: RESET Button, WIFI/Rfkill Togglebutton, WPS Button LEDS: Power, WAN, LAN 1-4, WLAN 2.4GHz, WLAN 5GHz, USB, WPS Serial: WARNING: The serial port needs a TTL/RS-232 3.3v level converter! The Serial setting is 115200-8-N-1. The 1x4 .1" header comes pre-soldered. Pinout: 1. 3v3 (Label printed on the PCB), 2. RX, 3. GND, 4. TX first install / debricking / restore stock: 0. Have a PC running a tftp-server @ 192.168.1.99/24 1. connect the PC to any LAN-Ports 2. put the openwrt...-factory.bin (or V1.00(ABCT.X).bin for stock) file into the tftp-server root directory and rename it to just "ras.bin". 3. power-cycle the router and hold down the the WPS button (for 30sek) 4. Wait (for a long time - the serial console provides some progress reports. The u-boot says it best: "Please be patient". 5. Once the power LED starts to flashes slowly and the USB + WPS LEDs flashes fast at the same time. You have to reboot the device and it should then come right up. Installation via Web-UI: 0. Connect a PC to the powered-on router. It will assign your PC a IP-address via DHCP 1. Access the Web-UI at 192.168.1.1 (Default Passwort: 1234) 2. Go to the "Expert Mode" 3. Under "Maintenance", select "Firmware-Upgrade" 4. Upload the OpenWRT factory image 5. Wait for the Device to finish. It will reboot into OpenWRT without any additional actions needed. To open the ZyXEL NBG6617: 0. remove the four rubber feet glued on the backside 1. remove the four philips screws and pry open the top cover (by applying force between the plastic top housing from the backside/lan-port side) Access the real u-boot shell: ZyXEL uses a proprietary loader/shell on top of u-boot: "ZyXEL zloader v2.02" When the device is starting up, the user can enter the the loader shell by simply pressing a key within the 3 seconds once the following string appears on the serial console: | Hit any key to stop autoboot: 3 The user is then dropped to a locked shell. |NBG6617> HELP |ATEN x[,y] set BootExtension Debug Flag (y=password) |ATSE x show the seed of password generator |ATSH dump manufacturer related data in ROM |ATRT [x,y,z,u] RAM read/write test (x=level, y=start addr, z=end addr, u=iterations) |ATGO boot up whole system |ATUR x upgrade RAS image (filename) |NBG6617> In order to escape/unlock a password challenge has to be passed. Note: the value is dynamic! you have to calculate your own! First use ATSE $MODELNAME (MODELNAME is the hostname in u-boot env) to get the challange value/seed. |NBG6617> ATSE NBG6617 |012345678901 This seed/value can be converted to the password with the help of this bash script (Thanks to http://www.adslayuda.com/Zyxel650-9.html authors): - tool.sh - ror32() { echo $(( ($1 >> $2) | (($1 << (32 - $2) & (2**32-1)) ) )) } v="0x$1" a="0x${v:2:6}" b=$(( $a + 0x10F0A563)) c=$(( 0x${v:12:14} & 7 )) p=$(( $(ror32 $b $c) ^ $a )) printf "ATEN 1,%X\n" $p - end of tool.sh - |# bash ./tool.sh 012345678901 | |ATEN 1,879C711 copy and paste the result into the shell to unlock zloader. |NBG6617> ATEN 1,0046B0017430 If the entered code was correct the shell will change to use the ATGU command to enter the real u-boot shell. |NBG6617> ATGU |NBG6617# Co-authored-by: David Bauer <mail@david-bauer.net> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for TP-Link Archer c7 v2Sibren Vasse2018-06-266-1/+278
| | | | Signed-off-by: Sibren Vasse <github@sibrenvasse.nl>
* ath79: add tl-wr2543-v1 supportLucian Cristian2018-06-265-0/+205
| | | | | | to switch between wlan leds we need a userspace implementation Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* kernel: bump 4.14 to 4.14.51Kevin Darbyshire-Bryant2018-06-2612-358/+19
| | | | | | | | | | | | | | | | | | | | | | | The sender domain has a DMARC Reject/Quarantine policy which disallows sending mailing list messages using the original "From" header. To mitigate this problem, the original message has been wrapped automatically by the mailing list software. Refresh patches. Remove patch that can be reverse applied: mvebu/patches-4.14/530-ATA-ahci_mvebu-enable-stop_engine-override.patch mvebu/patches-4.14/531-ATA-ahci_mvebu-pmp-stop-errata-226.patch Update patch that no longer applied: ipq806x/patches-4.14/0035-clk-mux-Split-out-register-accessors-for-reuse.patch Compiled-tested-for: lantiq, ramips Run-tested-on: lantiq BT hh5a, ramips MIR3g Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> Tested-by: Michael Yartys <michael.yartys@protonmail.com> Tested-by: Rosen Penev <rosenp@gmail.com>
* ath79: add support for ON Networks N150RZoltan HERPAI2018-06-265-2/+32
| | | | | | | | | | | | This is a rebranded Netgear WNR612v2, specs are the same. - Atheros AR7240 (Python) @400MHz - flash 4MB - ram 32MB - ethernet 10/100: 1xwan + 2xlan (only two) - radio AR9285 Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* ath79: add Netgear WNR612 v2Zoltan HERPAI2018-06-267-0/+189
| | | | | | | | | | | | | | | Netgear WNR612 v2: - cpu Atheros AR7240 (Python) @400MHz - flash 4MB - ram 32MB - ethernet 10/100: 1xwan + 2xlan (only two) - radio AR9285 As there is a rebranded WNR612v2 called ON Networks N150R, add a dtsi which includes all device support, and add a separate dts for the device only (with a separate one for the subsequent N150R). Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* ramips: RE350: add rootfs offset to headerAlex Maclean2018-06-261-1/+1
| | | | | | | Have mktplinkfw fill in the rootfs offset so the firmware splitter can find it without aligning to erase blocks. Signed-off-by: Alex Maclean <monkeh@monkeh.net>
* ramips: add support for TP-Link Archer C2Franz Flasch2018-06-256-0/+202
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - System-On-Chip: MT7620A - CPU/Speed: 580 MHz - Flash-Chip: Winbond 25Q64BVSIG - Flash size: 8192 KiB - RAM: 64 MiB - Wireless No1: SoC-integrated: MT7620A 2.4GHz 802.11bgn - Wireless No2: On-board chip: MT7610EN 5GHz 802.11ac - Switch: RTL8367RB Gigabit Switch - USB: Yes 1 x 2.0 Preparing a TFTP recovery image for initial flashing: Currently the only method to install openwrt for the first time is via TFTP download in u-boot. After first install you can use regular updates. WARNING: This method also overwrites the bootloader partition! Create a TFTP recovery image: 1) Download a stock TP-Link Firmware file here: https://www.tp-link.com/en/download/Archer-C2_V1.html#Firmware 2) Extract u-boot from the binary file: #> dd if=c2v1_stock_firmware.bin of=c2v1_uboot.bin bs=1 skip=512 count=131072 3) Now merge the sysupgrade image and the u-boot into one binary: #> cat c2v1_uboot.bin openwrt-squashfs-sysupgrade.bin > ArcherC2V1_tp_recovery.bin The resulting image can be flashed via TFTP recovery mode. Flash instructions: 1) To flash the recovery image, start a TFTP server from IP address 192.168.0.66 and serve the recovery image named ArcherC2V1_tp_recovery.bin. 2) Connect your device to the LAN port, then press the WPS/Reset button and power it up. Keep pressing the WPS/Reset button for 10 seconds. It will try to download the recovery image and flash it. It can take up to 20-25 minutes to finish. When it reaches 100%, the router will reboot itself. Signed-off-by: Serge Vasilugin <vasilugin@yandex.ru> Signed-off-by: Franz Flasch <franz.flasch@gmx.at>
* ramips: fix ZyXEL Keenetic Viva switch configFranz Flasch2018-06-251-1/+1
| | | | | | | | | The rtl8367b driver never supported a mdio property and it is quite likely that the switch never worked for the board. Use the mii-bus property instead to manage the switch via a mdio bus. Signed-off-by: Franz Flasch <franz.flasch@gmx.at>
* kernel: rtl8366-smi: add Realtek switch management via mii-busFranz Flasch2018-06-252-17/+141
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Current version of rtl8366-smi module only supports Realtek switch managment via two gpio lines. This adds Realtek switch management via mii_bus. Tested on a Tp-link Archer C2 v1 (Mediatek SoC mt7620a based) dts-file configuration should look like this: rtl8367rb { compatible = "realtek,rtl8367b"; realtek,extif1 = <1 0 1 1 1 1 1 1 2>; mii-bus = <&mdio0>; }; &ethernet { status = "okay"; mtd-mac-address = <&rom 0xf100>; pinctrl-names = "default"; pinctrl-0 = <&rgmii1_pins &rgmii2_pins &mdio_pins>; port@5 { status = "okay"; mediatek,fixed-link = <1000 1 1 1>; phy-mode = "rgmii"; }; mdio0: mdio-bus { status = "okay"; }; }; Signed-off-by: Serge Vasilugin <vasilugin@yandex.ru> Signed-off-by: Franz Flasch <franz.flasch@gmx.at>
* kernel: rtl8367b: drop redundant compatibleMathias Kresin2018-06-251-1/+0
| | | | | | | Remove the compatible without vendor prefix. It is formal wrong and not used in the tree. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ar71xx: Add support for TP-Link CPE210 v2Adrian Schmutzler2018-06-236-11/+101
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This PR adds support for a popular low-cost 2.4GHz N based AP Specifications: - SoC: Qualcomm Atheros QCA9533 (650MHz) - RAM: 64MB - Storage: 8 MB SPI NOR - Wireless: 2.4GHz N based built into SoC 2x2 - Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN Installation: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP adress:192.168.0.254 Notes: TP-Link does not use bootstrap registers so without this patch reference clock detects as 40MHz while it is actually 25MHz. This is due to messed up bootstrap resistor configuration on the PCB. Provided GPL code just forces 25MHz reference clock. That causes booting with completely wrong clocks, for example, CPU tries to boot at 1040MHz while the stock is 650MHz. So this PR depends on PR #672 to remove 40MHz reference clock. Thanks to Sven Eckelmann <sven@narfation.org> for properly patching that. Signed-off-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ar71xx: Add TP-Link Pharos v2 board detectionAdrian Schmutzler2018-06-232-14/+33
| | | | | | | | | | Add support for detecting TP-Link Pharos v2 boards. They use different format in product-info partition than v1 boards. Code was written mostly by Alexander Couzens <lynxis@fe80.eu> Signed-off-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* Re-enable arbitrary IPv6 addresses as outer ip4-in-ip6 tunnel source addressAxel Neumann2018-06-234-4/+4
| | | | | | | | | | | | | | | | The 666-Add-support-for-MAP-E-FMRs-mesh-mode.patch kernel patches break the possibility for using an ip4ip6 tunnel interface as a fall back interface accepting ip4-in-ip6 tunneled packets from any remote address. This works out of the box with any normal (non-666-patched) kernel and can be configured by setting up an 'ip -6 tunnel' with type 'any' or 'ip4ip6' and a remote address of '::'. The misbehavior comes with line 290 the patch which discards all packets that do not show the expected saddr, even if no single fmr rule was defined and despite the validity of the saddr was already approved earlier. Signed-off-by: Axel Neumann <neumann@cgws.de> Acked-by: Hans Dedecker <dedeckeh@gmail.com>
* mediatek: Add support for the UniElec U7623-02Kristian Evensen2018-06-2211-8/+805
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the MT7623A-based UniElec U7623-02 router, with eMMC storage and 512MB RAM. The router can be delivered with NAND Flash and more memory, but I only have access to the one configuration. The DTS is structured in such a way that adding support for more/different storage/memory should be straight forward. The device has the following specifications: * MT7623A (quad-core, 1.3 GHz) * 512MB RAM (DDR3) * 8GB storage (eMMC 4.5) * 2x normal miniPCIe slots * 1x miniPCIe slot that is connected via an internal USB OTG port * 5x 1Gbps Ethernet (MT7530 switch) * 1x UART header * 1x USB 3.0 port * 1x SATA 3.0 * 1x 40P*0.5mm FPC for MIPI LCD * 1x SIM slot * 12x LEDs (2 GPIO controlled) * 1x reset button * 1x DC jack for main power (12V) The following has been tested and is working: * Ethernet switch * miniPCIe slots (tested with Wi-Fi cards) * USB 3.0 port * sysupgrade * reset button Not working: * The miniPCIe connected via USB OTG. For the port to work, some MUSB glue must be added. I am currently in the process of porting the glue from the vendor SDK. Not tested: * SATA 3.0 * MIPI LCD Installation: The board ships with u-boot, and the first installation needs to be done via the bootloader using tftp. Step number one is to update the MBR of the eMMC, as the one that ships with the device is broken. Since the device can ship with different storage sizes, I will not provide the exact steps for creating a valid MBR. However, I have made some assumptions about the disk layout - there must be one 8MB recovery partition (FAT32) and a partition for the rootfs (Linux). The board loads the kernel from block 0xA00 (2560) and I have reserved 32MB for the kernel (65536 blocks). I have aligned the partitions on the erase block size (4096 byte), so the recovery partition must start on block 69632 and end on 86016 (16385 sectors). The rootfs is assumed to start on sector 90112. In order to install the mbr, you run the following commands from the u-boot command line: * tftpboot ${loadaddr} <name of mbr file> * mmc device 0 * mmc write ${loadaddr} 0x00 1 Run the following commands to install + boot OpenWRT: * tftpboot ${loadaddr} openwrt-mediatek-mt7623-7623a-unielec-u7623-02-emmc-512m-squashfs-sysupgrade-emmc.bin.gz * run boot_wr_img * run boot_rd_img * bootm Recovery: In order to recover the router, you need to follow the installation steps above (no need to replace MBR). Notes: * F2FS is used as the overlay filesystem. * The device does not ship with any valid MAC address, so a random address has to be generated. As a work-around, I write the initial random MAC to a file on the recovery partition. The MAC of the WAN interface is set to the MAC-address contained in this file on each boot, and the address of the LAN-interfaces are WAN + 1. The MAC file is kept across sysupgrade/firstboot. My approach is slightly different than what the stock image does. The first fives bytes of the MAC addresses in the stock image are static, and then the last byte is random. I believe it is better to create fully random MAC addresses. * In order to support the miniPCIe-slots, I needed to add missing pcie-nodes to mt7623.dtsi. The nodes are just c&p from the upstream dtsi. * One of the USB3.0 phys (u3phy2) on the board can be used as either USB or PCI, and one of the wifi-cards is connected to this phy. In order to support switching the phy from USB to PCI, I needed to patch the phy-driver. The patch is based on a rejected (at least last time I checked) PCI-driver submitted to the linux-mediatek mailing list. * The eMMC is configured to boot from the user area, and according to the data sheet of the eMMC this value can't be changed. * I tried to structure the MBR more nicely and use for example a FAT32-parition for the kernel, so that we don't need to write/read from some offset. The bootloader does not support reading from FAT32-paritions. While the command (fatload) is there, it just throws an error when I try to use it. * I will submit and hope to get the DTS for the device accepted upstream. If and when that happens, I will update the patches accordingly. Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-09 05:48:32 +0000