aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
...
* ramips: add support for RAVPower RP-WD009David Bauer2020-06-294-0/+220
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The RAVPower RP-WD009 is a batter-powered pocket sized router with SD card lot and USB port. Hardware -------- CPU: MediaTek MT7628AN RAM: 64M DDR2 FLASH: 16M GigaDevices SPI-NOR WLAN: MediaTek MT7628AN 2T2R b/g/n MediaTek MT7610E 1T1R n/ac ETH: 1x FastEthernet SD: SD Card slot USB: USB 2.0 Custom PMIC on the I2C bus (address 0x0a). Installation ------------ 1. Press and hold down the reset button. 2. Power up the Device. Keep pressing the reset button for 10 more seconds until the Globe LED lights up. 3. Attach your Computer to the Ethernet port. Assign yourself the address 10.10.10.1/24. 4. Access the recovery page at 10.10.10.128 and upload the OpenWrt factory image. 5. The flashing will take around 1 minute. The device will reboot automatically into OpenWrt. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: replace custom uImageArcher generationDavid Bauer2020-06-291-9/+1
| | | | | | | | | | | The replaces the custom uImageArcher build step with the generic uImage build step. The only different between these two is the difference in the generated name. Tested on: TP-Link Archer C59 v1 Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for WAVLINK WL-WN577A2Lars Wessels2020-06-294-1/+157
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the Wavlink WL-WN577A2 (black case) dual-band wall-plug wireless router. In Germany this device is sold under the brand name Maginon WL-755 (white case): Device specifications: - CPU: MediaTek MT7628AN (580MHz) - Flash: 8MB - RAM: 64MB - Bootloader: U-Boot - Ethernet: 2x 10/100 Mbps (Ralink RT3050) - 2.4 GHz: 802.11b/g/n SoC - 5 GHz: 802.11a/n/ac MT7610E - Antennas: internal - 4 green LEDs: 1 programmable (WPS) + LAN, WAN, POWER - Buttons: Reset, WPS - Small sliding power switch Flashing instructions (U-boot): - Configure a TFTP server on your PC/Laptop and set its IP to 192.168.10.100 - Rename the OpenWrt image to firmware.bin and place it in the root folder of the TFTP server - Power off (using the small sliding power switch on the left side) the device and connect an ethernet cable from its LAN or WAN port to your PC/Laptop - Press the WPS button (and keep it pressed) - Power on the device (using the small power switch) - After a few seconds, when the WAN/LAN LED stops blinking very fast, release the WPS button - Flashing OpenWrt takes less than a minute, system will reboot automatically - After reboot the WPS LED will indicate the current OpenWrt running status Signed-off-by: Lars Wessels <software@bytebox.org> [removed unused labels - fix whitespace errors - wrap commit message] Signed-off-by: David Bauer <mail@david-bauer.net>
* mvebu: move definition of factory.img out of Device/DefaultAdrian Schmutzler2020-06-282-1/+4
| | | | | | | | | | The Device/Default definition in mvebu defines an IMAGE/factory.img which is not included in IMAGES, and only used twice in the individual definitions. Move it out of the default definition to keep it closer to the reassignment of IMAGES and make it more consistent with respect to other values of IMAGE/factory.img Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq806x: set IMAGES in Device/Default definitionAdrian Schmutzler2020-06-281-7/+5
| | | | | | | | | | | | | The Device/Default definition sets a default IMAGE/sysupgrade.bin, but does not enable it by setting IMAGES. This is not consistent, and has led to IMAGES being defined at various other places in the file. Thus, this patch consolidates the default value for IMAGES by putting it in Device/Default. Since it's still overwritten where necessary, this patch is cosmetic. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq40xx: set IMAGES in Device/Default definitionAdrian Schmutzler2020-06-281-27/+13
| | | | | | | | | | | | | The Device/Default definition sets a default IMAGE/sysupgrade.bin, but does not enable it by setting IMAGES. This is not consistent, and has led to IMAGES being defined at various other places in the file. Thus, this patch consolidates the default value for IMAGES by putting it in Device/Default. Since it's still overwritten where necessary, this patch is cosmetic. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: do not build TP-Link tiny images by defaultAdrian Schmutzler2020-06-282-0/+3
| | | | | | | | | | | | | For quite some time, the tiny (4M flash) TP-Link sysupgrade and factory images cannot be built anymore by the buildbots, just the initramfs-kernel.bin files are still there. Disable these images for the buildbots and prevent useless builds. Note that these devices still build fine with default settings, even for kernel 5.4. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mvebu: remove non-existant board name solidrun,clearfog-a1Adrian Schmutzler2020-06-281-1/+0
| | | | | | | | | | | | | | In 02_network, the board name solidrun,clearfog-a1 is used in a case, but it does not seem to be used/exist anywhere else in OpenWrt. The valid strings are: - solidrun,clearfog-pro-a1 - solidrun,clearfog-base-a1 Fixes: 12795ec9f16b ("mvebu: split interface configuration for clearfog pro and base") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: build Compex WPJ531 cpximg filesLeon M. George2020-06-281-0/+28
| | | | | | | | | | | | | | | | | | | Generate additional images that are compatible to the cpximg loader. The cpximg loader can be started either by holding the reset button during power up or by entering the u-boot prompt and entering 'cpximg'. Once it's running, a TFTP-server under 192.168.1.1 will accept the image appropriate for the board revision that is etched on the board. For example, if the board is labelled '7A04': tftp -v -m binary 192.168.1.1 -c put openwrt-ath79-generic-compex_wpj531-16m-squashfs-cpximg-7A04.bin These files can also be used with the sysupgrade utility in stock images (add SSH key in luci for root access). Signed-off-by: Leon M. George <leon@georgemail.eu> [fix sorting of definitions] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for Compex WPJ531 (16M)Leon M. George2020-06-284-0/+160
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SoC: QCA9531 DRAM: 128MB DDR2 Flash: 16MB SPI-NOR 2 100MBit ethernet ports 2×2 2.4GHz on-board radio miniPCIe slot that supports 5GHz radio PoE 24V - 48V IEEE 802.3af optional USB 2.0 header Installation: To install, start a tftp server in bin/targets/ath79/generic/ and use the u-boot prompt over UART: tftpboot 0x80500000 openwrt-ath79-generic-compex_wpj531-16m-squashfs-sysupgrade.bin erase 0x9f030000 +$filesize erase 0x9f680000 +1 cp.b $fileaddr 0x9f030000 $filesize boot The cpximg file can be used with sysupgrade in the stock firmware (add SSH key in luci for root access). Another way is to hold the reset button during power up or running 'cpximg' in the u-boot prompt. Once the last LED starts flashing regularly, a TFTP-server under 192.168.1.1 will accept the image appropriate for the board revision that is etched on the board. For example, if the board is labelled '7A04': tftp -v -m binary 192.168.1.1 -c put openwrt-ath79-generic-compex_wpj531-16m-squashfs-cpximg-7A04.bin MAC addresses: <&uboot 0x2e010> *:cb (label) <&uboot 0x2e018> *:cc <&uboot 0x2e020> *:cd <&uboot 0x2e028> *:ce Only the first two are used (for ethernet), the WiFi modules have separate (valid) addresses. The latter two addresses are not used. Signed-off-by: Leon M. George <leon@georgemail.eu> [commit title/message facelift, fix rssileds, add led aliases] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for NETGEAR WAC124Jan Hoffmann2020-06-274-0/+39
| | | | | | | | | | | | | | | | | | | | | The WAC124 hardware appears to be identical to R6260/R6350/R6850. SoC: MediaTek MT7621AT RAM: 128M DDR3 FLASH: 128M NAND (Macronix MX30LF1G18AC) WiFI: MediaTek MT7603 bgn 2T2R MediaTek MT7615 nac 4T4R ETH: SoC Integrated Gigabit Switch (1x WAN, 4x LAN) USB: 1x USB 2.0 BTN: Reset, WPS LED: Power, Internet, WiFi, USB (all green) Installation: The factory image can be flashed from the stock firmware web interface or using nmrpflash. With nmrpflash it is also possible to revert to stock firmware. Signed-off-by: Jan Hoffmann <jan@3e8.eu>
* ramips: add support for Netgear R6080Alex Lewontin2020-06-274-0/+170
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the Netgear R6080, aka Netgear AC1000. The R6080 has almost the same hardware as the Netgear R6120, aka Netgear AC1200, but it lacks the USB port, has only 8 MiB flash and uses a different SERCOMM_HWID. Specification: SoC: MediaTek MT7628 (580 MHz) Flash: 8 MiB RAM: 64 MiB Wireless: 2.4Ghz (builtin) and 5Ghz (MT7612E) LAN speed: 10/100 LAN ports: 4 WAN speed: 10/100 WAN ports: 1 UART (57600 8N1) on PCB Installation: Flashing OpenWRT from stock firmware requires nmrpflash. Use an ethernet cable to connect to LAN port 1 of the R6080, and power the R6080 off. From the connected workstation, run `nmrpflash -i eth0 -f openwrt-ramips-mt76x8-netgear_r6080-squashfs-factory.img`, replacing eth0 with the appropriate interface (can be identified by running `nmrpflash -L`). Then power on the R6080. After flashing has finished, power cycle the R6080, and it will boot into OpenWRT. Once OpenWRT has been installed, subsequent flashes can use the web interface and sysupgrade files. Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com> [rebase and adjust for 5.4] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Fix ubnt_edgeswitch-8xp DEVICE_PACKAGESHauke Mehrtens2020-06-271-1/+1
| | | | | | | | switch-bcm53xx-mdio does not exists, use kmod-switch-bcm53xx-mdio instead. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Cc: Tobias Schramm <tobleminer@gmail.com>
* mvebu: LS421DE: dts file improvementsDaniel González Cabanelas2020-06-271-31/+22
| | | | | | | | | | | | - Delete useless HDD presence inputs: they aren't buttons, and probably they are outputs in the stock firmware. - Change the Function Button keycode: the current one isn't mapped by the kernel module. - Use the recommended property names for the ethernet stuff. - Add missing i2c pinmux. - Minor cosmetic changes. Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
* lantiq: remove unused PHY drivers on xrx200Aleksander Jan Bajkowski2020-06-272-12/+0
| | | | | | | | | | All boards on xrx200 use builtin switch and there is no supported device with external switch. It was copy paste from xway subtarget and was added in commit 18b76c66fbfea0e21ff66c6df432fa109c5bbb43. Save 20.3 kB flash memory. Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
* ramips: fix sd pollingQin Wei2020-06-271-0/+4
| | | | | | | | | | This is fixed in 18.06, it appears again in 19.07. Currently mt7628 sdcard driver do not support polling mode which is for the device do not have card-detect pin to detect sd card insert. Without this patch, device will not detect sdcard is inserted. This patch is a fix of that. Signed-off-by: Qin Wei <support@vocore.io>
* sunxi: add text referencing Allwinner H3 and H5 CPUsRogan Dawes2020-06-273-3/+3
| | | | | | This makes it a little easier to figure out which options to choose. Signed-off-by: Rogan Dawes <rogan@dawes.za.net>
* x86: Support Intel 10 Gigabit Ethernet CardsGregory L. Dietsche2020-06-271-1/+1
| | | | | | | Support Intel 10 Gigabit Ethernet Cards in x86/64 images by default. This ensures that systems with cards such as the Intel x520 will work properly. Signed-off-by: Gregory L. Dietsche <Gregory.Dietsche@cuw.edu>
* target/hack-5.4: platform/x86/pcengines: revert led simswich compromiseFlorian Eckert2020-06-261-0/+56
| | | | | | | | With this change the LED subsystem is abused in the kernel to switch the simswap. This change will be reverted, so we could use again the gpio subsystem. Signed-off-by: Florian Eckert <fe@dev.tdt.de>
* kernel: add pcengines-apu2 module descriptionFlorian Eckert2020-06-261-0/+17
| | | | | | | | Add a module description for the new pcengnies-apu2 device driver. This driver supports the front button and LEDs on the PC Engines APUv2/APUv3 boards. Signed-off-by: Florian Eckert <fe@dev.tdt.de>
* ath79: drop and consolidate redundant chosen/bootargsAdrian Schmutzler2020-06-2568-262/+12
| | | | | | | | | | | | | | In ath79, for several SoCs the console bootargs are defined to the very same value in every device's DTS. Consolidate these definitions in the SoC dtsi files and drop further redundant definitions elsewhere. The only device without any bootargs set has been OpenMesh OM5P-AC V2. This will now inherit the setting from qca955x.dtsi Note that while this tidies up master a lot, it might develop into a frequent pitfall for backports. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: drop redundant chosen/bootargsAdrian Schmutzler2020-06-2514-57/+1
| | | | | | | chosen/bootargs are defined to the same value in device DTS files that is already set in the SoC DTSI. Remove the redundant definitions. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for AVM FRITZ!WLAN Repeater DVB-CNatalie Kagelmacher2020-06-257-4/+138
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the AVM FRITZ!WLAN Repeater DVB-C SOC: Qualcomm Atheros QCA9556 RAM: 64 MiB FLASH: 16 MB SPI-NOR WLAN: QCA9556 3T3R 2.4 GHZ b/g/n and QCA9880 3T3R 5 GHz n/ac ETH: Atheros AR8033 1000 Base-T DVB-C: EM28174 with MaxLinear MXL251 tuner BTN: WPS Button LED: Power, WLAN, TV, RSSI0-4 Tested and working: - Ethernet (correct MAC, gigabit, iperf3 about 200 Mbit/s) - 2.4 GHz Wi-Fi (correct MAC) - 5 GHz Wi-Fi (correct MAC) - WPS Button (tested using wifitoggle) - LEDs - Installation via EVA bootloader (FTP recovery) - OpenWrt sysupgrade (both CLI and LuCI) - Download of "urlader" (mtd0) Not working: - Internal USB - DVB-C em28174+MxL251 (depends on internal USB) Installation via EVA bootloader (FTP recovery): Set NIC to 192.168.178.3/24 gateway 192.168.178.1 and power on the device, connect to 192.168.178.1 through FTP and sign in with adam2/adam2: ftp> quote USER adam2 ftp> quote PASS adam2 ftp> binary ftp> debug ftp> passive ftp> quote MEDIA FLSH ftp> put openwrt-sysupgrade.bin mtd1 Wait for "Transfer complete" together with the transfer details. Wait two minutes to make sure flash is complete (just to be safe). Then restart the device (power off and on) to boot into OpenWrt. Revert your NIC settings to reach OpenWrt at 192.168.1.1 Signed-off-by: Natalie Kagelmacher <nataliek@pm.me> [fixed sorting - removed change to other board - prettified commit message] Signed-off-by: David Bauer <mail@david-bauer.net>
* bcm47xx: add support for NETGEAR R6200 V1Edward Matijevic2020-06-245-11/+73
| | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds supports for the NETGEAR R6200 V1 This device is mainlined in Linux as of 5.4 Specification: - SOC: Broadcom BCM4718A1 (480 MHz) - Flash: 16MB (Macronix MX25L128) - RAM: 128MB DDR2 - SWITCH: BCM53125 - Ethernet: 5x GE (1 WAN + 4 LAN, Inverted order) - WLAN 2.4G: In SOC - WLAN 5GHz: miniPCIe card, BCM4352 (ID: 4360) - USB: 1x USB 2.0 port (Type A) - Buttons: Reset, WLAN, WPS - LED: Amber for Power, others need a workaround - UART: 1x UART on PCB LED Issues: They are controlled by a 74HC164 via bit banging(GPIO 6/7) Firmware Install Instructions ============================= Using the device specific .chk, use that file to perform a normal device upgrade in the OEM admin page. Signed-off-by: Edward Matijevic <motolav@gmail.com>
* ramips: clean up Netgear R6120 code formattingAlex Lewontin2020-06-231-1/+1
| | | | | | | This commit performs minor janitorial work to clean up some code formatting for the Netgear R6120. Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
* ramips: move Netgear R6120 LED trigger to DTSAlex Lewontin2020-06-232-6/+3
| | | | | | | | | | | | This moves the trigger for the Netgear R6120's wlan2g_green LED from base-files/etc/board.d/01_leds to the device-tree file. This has been applied to R6120 based on findings for the very similar Netgear R6080. Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com> [merge case in 01_leds, slightly adjust commit message/title] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mvebu: consolidate DTS filesAdrian Schmutzler2020-06-2312-837/+0
| | | | | | | | | | | | The DTS files in files-4.19 and files-5.4 are exactly identical except for one file (armada-3720-uDPU.dts), which is only present for 4.19, as it has been upstreamed before 5.4. Since there is no point in maintaining all these identical files twice, this patch moves them to the "files" directory, only keeping the named exception to files-4.19. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq40xx: consolidate DTS filesAdrian Schmutzler2020-06-2387-10517/+0
| | | | | | | | | | | | | | | The DTS files in files-4.19 and files-5.4 are exactly identical except for one file (qcom-ipq4018-emr3500.dts), which is only present for 5.4. Since there is no point in maintaining all these identical files twice, this patch moves them to the "files" directory. If there ever was a new kernel with substantial DTS changes, a new folder would need to be introduced anyway and could easily be done. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mvebu: fix default EU regdomain for Linksys WRT AC devicesJose Olivera2020-06-231-1/+1
| | | | | | | | | | | | | | | | | | | | | The mwlwifi driver sets the default country code for EU (fi- rmware region code 0x30) certified devices to FR (France), not DE (Germany). Whilst this is a trivial fix, novice users may not know how mwlwifi negatively reacts to a non-matching country code and may leave the setting alone. Especially si- nce it is under the advanced settings section in LuCI. Relevant mwlwifi driver code: https://github.com/kaloz/mwlwifi/commit/0a550312ddb5a9e00e8d602d5571598f25a78158 The mwlwifi driver readme states "Please don't change country code and let mwlwifi set it for you." However, OpenWrt's current behaviour does not adhere to this with its default, 'just flashed from factory' setting for EU devices. Signed-off-by: Jose Olivera <oliverajeo@gmail.com> [rebase, extend commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* armvirt,x86: fix build breakage of crypto ccp modulePetr Štetiar2020-06-232-0/+2
| | | | | | | | | Upstream in commit f9f8f0c24203 ("crypto: ccp -- don't "select" CONFIG_DMADEVICES") removed dependency on CONFIG_DMADEVICES symbol which leads to build breakage of ccp crypto module, so fix this by adding that symbol back in the kernel config. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* bcm63xx: AV4202N: add missing PCI pinmuxDaniel González Cabanelas2020-06-221-0/+5
| | | | | | | | | The ADB P.DG AV4202N device has a wifi chipset connected via PCI. But the PCI pinmux is missing and without it the wifi won't work properly. Add the pinctrl_pci to enable the missing PCI pins for this device. Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
* kernel: bump 5.4 to 5.4.48Petr Štetiar2020-06-2227-83/+40
| | | | | | | | | | | | | | | | Resolved merge conflict in the following patches: layerscape: 701-net-0213-dpaa2-eth-Add-CEETM-qdisc-support.patch ramips: 0013-owrt-hack-fix-mt7688-cache-issue.patch Refreshed patches, removed upstreamed patch: bcm63xx: 020-v5.8-mtd-rawnand-brcmnand-fix-hamming-oob-layout.patch Run tested: qemu-x86-64 Build tested: x86/64 Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: image: fix initramfs for safeloader devicesPetr Štetiar2020-06-221-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently it's not possible to tftpboot initramfs image on archer-c7-v5 as the image contains tplink-v1-header which leads to: ath> bootm ## Booting image at 81000000 ... Bad Magic Number as U-Boot expects uImage wrapped image. This is caused by following inheritance issue: define Device/Init KERNEL_INITRAMFS = $$(KERNEL) define Device/tplink-v1 KERNEL := kernel-bin | append-dtb | lzma KERNEL_INITRAMFS := kernel-bin | append-dtb | lzma | tplink-v1-header define Device/tplink-safeloader $(Device/tplink-v1) define Device/tplink-safeloader-uimage $(Device/tplink-safeloader) KERNEL := kernel-bin | append-dtb | lzma | uImageArcher lzma define Device/tplink_archer-c7-v5 $(Device/tplink-safeloader-uimage) where tplink-v1 defines KERNEL_INITRAMFS with tplink-v1-header and it's then used by all devices inheriting from tplink-safeloader. Fix this by overriding KERNEL_INITRAMFS to KERNEL variable again. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* lantiq: fritz7312: set maximum speed to 100 mbit on 5.4Adrian Schmutzler2020-06-211-0/+1
| | | | | | | | | | | | The fritz 7312 does not support 1000 gbit. Advertising it makes it worse. Some NIC will change to 1000 gibt and turn off and on again for ever. The previous patch in 36f628910b8b was only applied to the 4.19 file, so let's just make it consistent with this patch. Cc: Alexander Couzens <lynxis@fe80.eu> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: fix input type for TP-Link TL-WR902AC v1 mode switchLech Perczak2020-06-211-0/+2
| | | | | | | | | Inputs assigned to "mode select" switch on the side of the device were missing linux,input-type property. This would cause them do incorrectly generate EV_KEY events. Fix this by setting the linux,input-type = <EV_SW> property on them. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ramips: add support for ELECOM WRC-2533GST2INAGAKI Hiroshi2020-06-215-31/+118
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | ELECOM WRC-2533GST2 is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on MT7621A. Specification: - SoC : MediaTek MT7621A - RAM : DDR3 256 MiB - Flash : SPI-NOR 32 MiB - WLAN : 2.4/5 GHz 4T4R (2x MediaTek MT7615) - Ethernet : 10/100/1000 Mbps x5 - Switch : MediaTek MT7530 (SoC) - LED/keys : 4x/6x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J4: 3.3V, GND, TX, RX from ethernet port side - 57600n8 - Power : 12VDC, 1.5A Flash instruction using factory image: 1. Boot WRC-2533GST2 normally 2. Access to "http://192.168.2.1/" and open firmware update page ("ファームウェア更新") 3. Select the OpenWrt factory image and click apply ("適用") button 4. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: add MT7615 wireless support for ELECOM WRC-GST devicesINAGAKI Hiroshi2020-06-212-1/+30
| | | | | | | | | ELECOM WRC-1900GST and WRC-2533GST have two MT7615 chips for 2.4/5 GHz wireless. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> [WRC-1900GST] Acked-by: NOGUCHI Hiroshi <drvlabo@gmail.com>
* ramips: increase SPI frequency for ELECOM WRC-GST devicesINAGAKI Hiroshi2020-06-211-1/+1
| | | | | | | | | | | Increase the SPI frequency for ELECOM WRC-1900GST and WRC-2533GST to 40 MHz by updating the common DTSI file. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> [WRC-1900GST] Acked-by: NOGUCHI Hiroshi <drvlabo@gmail.com> [split patch, adjust commit title/message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add label-mac-device for ELECOM WRC-GST devicesINAGAKI Hiroshi2020-06-211-1/+2
| | | | | | | | | | | Update the dtsi for ELECOM WRC-1900GST and WRC-2533GST to add label-mac-device alias. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> [WRC-1900GST] Acked-by: NOGUCHI Hiroshi <drvlabo@gmail.com> [split patch, adjust commit title/message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for TP-Link CPE610 v2Andrew Cameron2020-06-204-0/+48
| | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link CPE610 v2 is an outdoor wireless CPE for 5 GHz with one Ethernet port based on Atheros AR9344 Specifications: - 560/450/225 MHz (CPU/DDR/AHB) - 1x 10/100 Mbps Ethernet - 64 MB of DDR2 RAM - 8 MB of SPI-NOR Flash - 23dBi high-gain directional 2×2 MIMO antenna and a dedicated metal reflector - Power, LAN, WLAN5G green LEDs - 3x green RSSI LEDs Flashing instructions: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP adress:192.168.0.254 Signed-off-by: Andrew Cameron <apcameron@softhome.net>
* ath79: add support for TP-Link TL-WA801ND v3/v4Adrian Schmutzler2020-06-196-0/+169
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This ports support for these devices from ar71xx. Specification: - System-On-Chip: Qualcomm Atheros QCA9533 - CPU/Speed: v3: 560 MHz, v4: 650 MHz - Flash: 4096 KiB - RAM: 32 MiB - Ethernet: 1 port @ 100M - Wireless: SoC-integrated: QCA9533 2.4GHz 802.11bgn In contrast to the implementation in ar71xx (reset and WiFi button), the device actually features reset and WPS buttons. Flashing instructions: Upload the ...-factory.bin file via OEM web interface. TFTP Recovery: 1. Set PC to fixed IP address 192.168.0.66 2. Download *-factory.bin image and rename it to wa801ndv3_tp_recovery.bin 3. Start a tftp server with the image file in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery. TFTP recovery has only been tested with v3, and the Wiki states that the procedure won't work for v4, which cannot be verified or falsified at the moment. Tested by Tim Ward (see forum): https://forum.openwrt.org/t/ath79-support-for-tp-link-tl-wa901nd-v3-v4-v5/61246/13 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* bcm63xx: DGND3700v1: fix port orderDaniel González Cabanelas2020-06-191-4/+4
| | | | | | | | | Fix the switch LAN labels for the DGND3700v1/DGND3800B router, the order is reversed. Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com> [cut out of bigger patch, adjust commit title/message accordingly] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* bcm63xx: HG622: enable LAN LEDsDaniel González Cabanelas2020-06-191-1/+3
| | | | | | | | | The Huawei Echolife HG622 has hardware controlled LAN LEDs. Add the ephy led pinctrl to let the router show LAN activity on these LEDs. Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
* ath79: set &eth1 status for TP-Link CPE devices in parent DTSIAdrian Schmutzler2020-06-184-6/+4
| | | | | | | The status is set to "okay" for all devices on ar9344, so just move this to the parent DTSI. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: define CONFIG_MFD_RB4XX_CPLD to fix build breakageHannu Nyman2020-06-172-0/+2
| | | | | | | | | | | | | | Define the kernel config symbol CONFIG_MFD_RB4XX_CPLD=n to fix build breakage on non-mikrotik targets. The driver was added for all ath79, but the symbol was only defined for mikrotik subtarget. Fixes: fa70b3a4bbc6 ("ath79: add Mikrotik rb4xx series drivers") Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi> [rearrange commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* lantiq: drop "CONFIG_HZ_100 is not set"Adrian Schmutzler2020-06-172-2/+0
| | | | | | | | | | CONFIG_HZ_100 is not set to "y" in generic config anymore since 3a761c90afc0 ("treewide: Don't diverge from upstream default HZ settings on 4.19"), so we don't need to disable it anymore either. This was the only remaining case in the entire tree. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* lantiq: switch to 5.4Aleksander Jan Bajkowski2020-06-171-2/+1
| | | | | | Runtime tested on BT Home Hub 5A and D-Link DWR-966. Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
* kernel: bump 5.4 to 5.4.46Petr Štetiar2020-06-162-3/+3
| | | | | | | | | Refreshed patches. Run tested: qemu-x86-64, wrt3200acm Build tested: x86/64, imx6, mvebu/cortexa9, sunxi/a53 Signed-off-by: Petr Štetiar <ynezz@true.cz>
* mvebu: fix bootloader kernel commandline manglingPetr Štetiar2020-06-161-27/+34
| | | | | | | | | | | | Currently I'm unable to boot initramfs image with `console=ttyS0,115200` kernel commandline as the kernel commandline mangling resets kernel commandline if there is no `root=` option provided, efectively clearing whatever I pass to the kernel, making the `root=` option mandatory. So if the kernel commandline mangling is not appropriate just leave the kernel commandline as it is. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* mediatek: mt7623: refresh kernel 5.4 configSungbo Eo2020-06-161-44/+7
| | | | | | By running make kernel_oldconfig and selecting relevant options. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-07 16:50:39 +0000