aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
* ath79: add support for TP-Link RE350K v1Piotr Dymacz2019-03-114-0/+194
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link RE350K v1 (FCC ID: TE7RE350K) is a wall-plug AC1200 Wi-Fi range extender with 'Kasa Smart' support. Device is based on Qualcomm/Atheros QCA9558 + QCA9882 + AR8035 platform and is available only on US market. Specification: - 720/600/200 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of flash (SPI NOR) - 1x 1 Gbps Ethernet (AR8035) - 2T2R 2.4 GHz (QCA9558), with ext. PA (SE2565T) and LNA (SKY65971-11) - 2T2R 5 GHz (QCA9882), with ext. PA (SE5003L1-R) and LNA (SKY65981-11) - 2x U.FL connector on PCB - 2x dual-band PCB antennas - 1x LED, 2x dual-color LED (all driven by GPIO) - 3x button (app config, led, reset) - 1x mechanical on/off slide switch - 1x UART (4-pin, 2.54 mm pitch) header on PCB - 1x JTAG (8-pin, 1.27 mm pitch) header on PCB Flash instruction: Use 'factory' image directly in vendor GUI (default IP: 192.168.0.254, default credentials: admin/admin). Warning: This device does not include any kind of recovery mechanism in U-Boot. Vendor firmware access: You can access vendor firmware over serial (RX line requires jumper resistor in R306 place, near XTAL) with: root/sohoadmin credentials. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ramips: add support for ALFA Network Tube-E4GPiotr Dymacz2019-03-114-0/+204
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network Tube-E4G is an outdoor, dual-SIM LTE Cat. 4 CPE, based on MediaTek MT7620A, equipped with Quectel EC25 miniPCIe modem. Specification: - MT7620A (580 MHz) - 64/128/256 MB of RAM (DDR2) - 16/32 MB of flash (SPI NOR) - 1x 10/100 Mbps Ethernet, with passive PoE support (24 V) - 1x miniPCIe slot (with PCIe and USB 2.0 buses) - 2x SIM slot (mini, micro) with detect and switch driven by GPIO - 1x detachable antenna (modem main) - 1x internal antenna (modem div) - 1x GPS passive antenna (optional) - 5x LED (all driven by GPIO) - 1x button (reset) - UART (4-pin, 2.54 mm pitch) header on PCB Other: Default SIM slot is selected at an early stage by U-Boot, based on 'default_sim' environment value: 1 or unset = SIM1 (mini), 2 = SIM2 (micro). U-Boot also resets the modem, using #PERST signal, before starting kernel. Flash instruction: You can use the 'sysupgrade' image directly in vendor firmware which is based on OpenWrt (make sure to not preserve settings - use 'sysupgrade -n -F ...' command). Alternatively, use web recovery mode in U-Boot: 1. Power the device with reset button pressed, the LAN LED will start blinking slowly and after ~3 seconds, when it starts blinking faster, you can release the button. 2. Setup static IP 192.168.1.2/24 on your PC. 3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* mxs: disable unused serial driversMichael Heimpold2019-03-111-3/+1
| | | | | | | | | | | | | | | | This disables PL010 and 8250 serial support for this platform as both drivers are not used: the debug UART is PL011 and the application UARTs use a dedicated MXS specific driver. The kernel size reduction is neglectable, but it also removes the non-working (confusing) /dev/ttyS0 and /dev/ttyS1 devices in a running system (which generate errors when trying to use): root@OpenWrt:~# echo "hello world" > /dev/ttyS0 ash: write error: I/O error root@OpenWrt:~# Signed-off-by: Michael Heimpold <mhei@heimpold.de>
* oxnas: fix oxnas-rps-timer dt-matchDaniel Golle2019-03-111-0/+10
| | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* oxnas: replace oxnas-restart with version to be submitted to upstreamDaniel Golle2019-03-111-103/+136
| | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* IB: include SUPPORTED_DEVICES in 'make info' outputDaniel Golle2019-03-111-2/+3
| | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* oxnas: use generic filenames for image and DTSDaniel Golle2019-03-114-20/+28
| | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* oxnas: move PCIe controller outside of simple-busDaniel Golle2019-03-103-95/+118
| | | | | | | | Move PCIe controller outside down to SoC level to avoid resource mapping problems. Also add more detailed error handling when mapping registers. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* lantiq: Refresh kernel 4.14 configurationHauke Mehrtens2019-03-101-0/+2
| | | | | | | This adds two configuration options which are getting automatically added. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* oxnas: fix PCIe register ranges in device-treeDaniel Golle2019-03-101-2/+2
| | | | | | | They should be relative to apb-bridge@47000000 rather than to the pcie-controller@c00000 inside it. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* layerscape: use wrapped nand_do_upgrade for traverse-ls1043 boardsMathew McBride2019-03-101-50/+15
| | | | | | | | Traverse LS1043 boards are set up with a dual-system layout, rootfs{1,2} and kernel{1,2}. nand_do_upgrade can do the image replacement work we were doing before as long as we give it the partition names. This greatly simplifies the /lib/upgrade/platform.sh. Signed-off-by: Mathew McBride <matt@traverse.com.au>
* layerscape: rename Traverse boards along SoC linesMathew McBride2019-03-102-9/+7
| | | | | | | | | Upcoming product specification and branding changes mean that the names in tree do not accurately reflect released products. To reduce any confusion, sort our boards by SoC family, e.g traverse-ls1043. Any future boards using Layerscape family SoC's will be treated the same way, e.g Device/traverse-ls/lx/laXXXX. The affected boards so far have only been available through OEM channels and those aren't using the provided sysupgrade. Signed-off-by: Mathew McBride <matt@traverse.com.au>
* ltq-atm/ltq-ptm: re-enable/fix reset_ppe() functionality for VR9Martin Schiller2019-03-101-0/+2
| | | | | | | | | | | | | | | This patch re-enables the reset_ppe() functionality for VR9 targets by using the new lantiq rcu subsystem. The reset sequence in the reset_ppe() function was taken from the ppa datapath driver of lantiq UGW 7.4.1. Additionally it adds the required reset definitions to the vr9 dtsi file. It also prepares the reset_ppe() function calls for the other lantiq targets. This feature is needed to be able to switch between ltq-atm/ltq-ptm driver in ATM/PTM Auto-Mode at runtime. Signed-off-by: Martin Schiller <ms@dev.tdt.de>
* lantiq: add support for AVM FRITZ!Box 7362 SLDanijel Tudek2019-03-105-1/+157
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware: - SoC: Lantiq VRX288 - RAM: Winbond W971GG6JB 1 Gb (128 MiB) - Flash: - SPI: 8 Mb (1 MiB) for bootloader and tffs - NAND: 1 Gb (128 MiB) for OS - xDSL: Lantiq VRX208 - WLAN: Atheros AR9381 - DECT: Dialog Semiconductors SC14441 Everything except FXS/DECT works (no drivers for AVM's FXS implementation with SC14441). Installation via FTP: 1. Use scripts/flashing/eva_ramboot.py to send initramfs-kernel.bin to the device when powering on. Standard AVM procedures with finding the correct IP address and the right moment to open FTP apply here (approx. 4 seconds on 7362SL). IMPORTANT: set lzma compression in ramdisk options, bootloader stalls when receiving uncompressed images. 2. Transfer sysupgrade.bin image with scp to /tmp directory and run sysupgrade 3. First boot might take a bit longer if linux_fs_start was set to 1, in that case the device will reboot twice, first time it will fail to load second kernel (overwritten by ubifs), set linux_fs_start to 0 and reboot. OpenWrt uses the entire NAND flash. Kernel uses 4 MiB and rootfs uses the rest of 124 MiB, overwriting everything related to FRITZ!OS - both OS images, config and answering machine/media server data. To return to FRITZ!OS, use AVM's recovery image. Signed-off-by: Danijel Tudek <danijel.tudek@gmail.com>
* lantiq: move common FRITZ736X bits into dtsiDanijel Tudek2019-03-102-181/+228
| | | | | | | Move common FRITZ736X bits into dtsi file as a preparation for FRITZ7362SL support. Signed-off-by: Danijel Tudek <danijel.tudek@gmail.com>
* lantiq: add support for AVM FRITZ!Box 7412Andy Binder2019-03-105-0/+254
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware: SoC: Lantiq VRX 220 CPU Cores: 2x MIPS 34Kc at 500 MHz RAM: 128 MiB 250 MHz Storage: 128 MiB NAND flash Ethernet: built-in Fast Ethernet switch, only port 2 is used Wireless: Atheros AR9287-BL1A b/g/n with 2 pcb antennas Modem: built-in A/VDSL2 modem DECT: Dialog SC14441 LEDs: 1 two-color, 4 one-color Buttons: 2 FXS: 1 port via TAE or RJ12 connector Everything except FXS/DECT works (no drivers for AVM's FXS implementation with SC14441). Installation: Use the eva_ramboot.py script to load an initramfs image on the device. Run it a few seconds after turning the device on. $ scripts/flashing eva_ramboot 192.168.178.1 bin/targets/lantiq/xrx200/openwrt-lantiq-xrx200-avm_fritz7412-initramfs-kernel.bin If it fails to find the device try the ip address 169.254.120.1. (Firmware updates or the recovery tool apparently change it.) IMPORTANT: set lzma compression in ramdisk options, bootloader stalls when receiving uncompressed images. The device will load it in ram and boot it. You can reach it under the openwrt default ip address 192.168.1.1. Check if the key linux_fs_start is not set to 1 in tffs: $ fritz_tffs_nand -d /dev/mtd1 -n linux_fs_start If it is set to 1, the bootloader will select the wrong set of partitions. Restart the box and install an FritzOS upgrade or do a recovery. Afterwards start again at step 1. Run sysupgrade to persistently install OpenWRT. Signed-off-by: Valentin Spreckels <Valentin.Spreckels@Informatik.Uni-Oldenburg.de> Signed-off-by: Andy Binder <AndyBinder@gmx.de>
* sunxi: add support for Orange Pi PC PlusAleksander Jan Bajkowski2019-03-091-0/+10
| | | | | | | | | | | | | | | | | CPU: H3 Quad-core Cortex-A7 H.265/HEVC 4K @ 1.2 Ghz GPU: Mali400MP2 GPU @ 600MHz (supports OpenGL ES 2.0) Memory: 1GB DDR3 (shared with GPU) Onboard: Storage TF card (Max. 64GB) / MMC card slot Onboard: Storage 8 GB eMMC Onboard: Network 10/100M Ethernet RJ45 Onboard: Network WiFi 802.11 b/g/n (Realtek RTL8189FTV) Onboard header: SPI, I2C, GPIO, UART USB 2.0: Three USB 2.0 HOST, One USB 2.0 OTG Known issues: -Wifi diesn't work Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
* ath79: add support for YunCore A770Piotr Dymacz2019-03-095-1/+143
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | YunCore A770 is a ceiling AC750 AP with 2 Fast Ethernet ports, PoE (802.3at) support, based on QCA9531 + QCA9887. Specification: - 650/597/216 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of flash (SPI NOR) - 2x 10/100 Mbps Ethernet (PoE 802.3at support in WAN port) - 2T2R 2.4 GHz (QCA9531), with ext. PA and LNA - 1T1R 5 GHz (QCA9887), with ext. FEM (SKY85728-11) - 2x regular LED, 1x RGB LED (all driven by GPIO) - 1x button (reset) - DC jack for main power input (12 V) - UART header on PCB Flash instruction: 1. First, gain root access to the device, following below steps: - Login into web gui (default password/IP: admin/192.168.188.253). - Go to 'Advanced' -> 'Management' -> 'System' and download backup of configuration (bakfile.bin). - Open the file as tar.gz archive, edit/update 'shadow' file and change hash of root password to something known. - Repack the archive, rename it back to 'bakfile.bin' and use to restore configuration of the device. - After that, device will reboot and can be accessed over SSH. 2. Then, install OpenWrt: - Login over SSH and issue command: fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000" - Upload 'sysupgrade' image and install it (only if previous command succeeded) with command: 'sysupgrade -n -F openwrt-...'. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ipq40xx: backport I2C QUP driver changes from 4.17Piotr Dymacz2019-03-0813-0/+2781
| | | | | | | | | | | | | | | | | | | | | | | | Backport below changes for I2C QUP driver from v4.17: 0668bc44a426 i2c: qup: fix copyrights and update to SPDX identifier 7239872fb340 i2c: qup: fixed releasing dma without flush operation completion eb422b539c1f i2c: qup: minor code reorganization for use_dma 6d5f37f166bb i2c: qup: remove redundant variables for BAM SG count c5adc0fa63a9 i2c: qup: schedule EOT and FLUSH tags at the end of transfer 7e6c35fe602d i2c: qup: fix the transfer length for BAM RX EOT FLUSH tags 3f450d3eea14 i2c: qup: proper error handling for i2c error in BAM mode 08f15963bc75 i2c: qup: use the complete transfer length to choose DMA mode ecb6e1e5f435 i2c: qup: change completion timeout according to transfer length 6f2f0f6465ac i2c: qup: fix buffer overflow for multiple msg of maximum xfer len f7714b4e451b i2c: qup: send NACK for last read sub transfers fbfab1ab0658 i2c: qup: reorganization of driver code to remove polling for qup v1 7545c7dba169 i2c: qup: reorganization of driver code to remove polling for qup v2 This fixes various I2C issues observed on AP120C-AC board equipped with Atmel/Microchip AT97SC3205T TPM module. Tested-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ipq40xx: add ath10k-calibration-variant in AP120C-AC DTSPiotr Dymacz2019-03-082-0/+2
| | | | | | | | Use 'ath10k-calibration-variant' (with the value sent upstream) for the second (5 GHz) radio in AP120C-AC board DTS. First radio uses the same BDF as in one of Qualcomm reference designs. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ib: show current revision based on $(REVISION)Paul Spooren2019-03-081-0/+1
| | | | | | | | This is useful in for the attendedsyupsgrade server (asu) to distinguish between snapshot version. Currently asu can't tell devices requesting a snapshot build if the same build is already installed. Signed-off-by: Paul Spooren <mail@aparcar.org>
* ib: show unified target based on $(TARGETID)Paul Spooren2019-03-081-1/+1
| | | | | | | Instead of showing a slightly more readable target like "ar71xx (Generic)" print the more generic format "ar71xx/genric" Signed-off-by: Paul Spooren <mail@aparcar.org>
* kernel: bump 4.14 to 4.14.105Koen Vandeputte2019-03-074-11/+11
| | | | | | | | | Refreshed all patches. Compile-tested on: ar71xx, cns3xxx, imx6, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.162Koen Vandeputte2019-03-071-1/+1
| | | | | | | | | Refreshed all patches. Compile-tested on: ar7 Runtime-tested on: none Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* owl-loader: fix crash caused by endian patchChristian Lamparter2019-03-061-1/+1
| | | | | | | | | | | This patch fixes a crash that occured on the BT Home Hub v5a (lantiq/xrx200) which resulted in the device bootlooping. Reported-by: Ryan Mounce <ryan@mounce.com.au> Tested-by: Vitalij Alshevsky <v_alshevsky@tut.by> Fixes: ddece08bf456 ("kernel: owl-loader: fix sparse endian warnings") Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* mips: fix dynamic ftraceMantas Pucka2019-03-063-9/+24
| | | | | | This was fixed for v4.9 in 076d2ea68, now port to all kernels Signed-off-by: Mantas Pucka <mantas@8devices.com>
* ramips: rework network settings for HC5861Chen Minqiang2019-03-062-18/+14
| | | | | | | dts: disable port4 and leave it ephy mode because it connect to nothing switch port5 connected to GE port we use it as wan port Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* ar71xx: enable QCA955x SGMII fixup on RambutanMantas Pucka2019-03-061-0/+2
| | | | | | | | | fixes intermittent loss of connectivity on 1Gbit port, with log message: 803x_aneg_done: SGMII link is not ok Signed-off-by: Mantas Pucka <mantas@8devices.com>
* lantiq: enlarge ZyXEL P-2812HNU-F1 kernel partition (FS#2124)Christian Lamparter2019-03-062-3/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The current snapshot release kernel with it's 2119245 Byte size is too big to fit into the 2097152 (2MiB) area that was set aside for the kernel. Which causes the device to fail to boot (after an update or even during a fresh install) NAND read: device 0 offset 0x60000, size 0x200000 2097152 bytes read: OK ## Booting kernel from Legacy Image at 80800000 ... Image Name: MIPS OpenWrt Linux-4.14.98 Created: 2019-02-13 9:37:36 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 2119245 Bytes = 2 MiB Load Address: 80002000 Entry Point: 80002000 Verifying Checksum ... Bad Data CRC ERROR: can't get kernel image! This patch fixes the problem by enlarging the kernel partition at the cost of the ubi/data partition behind it. The patch also adds a KERNEL_SIZE variable to the image Makefile to prevent silent corruptions from happening in the future. Please note: The u-boot environment for the router also needs to be updated. So please attach an appropriate serial converter cable and enter the following commands into the u-boot prompt: setenv nboot 'nand read 0x80800000 0x60000 0x300000; bootm 0x80800000' saveenv The wiki has been updated accordingly: <https://openwrt.org/toh/zyxel/p2812hnu-f1> Fixes: FS#2124 Suggested-by: Mafketel (User on bugs.openwrt.org) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ib: display whether profile comes with image metadataDaniel Golle2019-03-061-1/+1
| | | | | | | | Having image metadata (and signature) appended is a condition for semi-automated sysupgrade, hence IB needs to be able to tell which images will end up with metadata. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: mt7620: export chip version and pkgDaniel Golle2019-03-061-0/+19
| | | | | | | | | | | Similar to the (currently unused) mt7620_get_eco() function, introduce mt7620_get_chipver() and mt7620_get_pkg() functions to allow rt2x00 to probe for the type of WiSoC. This is ugly and probably unacceptable for upstream, however, it should help to evaluate which of those hacks are actually really needed, enumerate the possible values and label them in a more meaningful way than currently done in the vendor driver. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: fix refcnt leak in LED netdev trigger on interface renameRafał Miłecki2019-03-052-0/+138
| | | | | | | | | | This fixes a possible unbalanced dev_hold(): > iw dev bar del [ 237.355366] unregister_netdevice: waiting for bar to become free. Usage count = 1 [ 247.435362] unregister_netdevice: waiting for bar to become free. Usage count = 1 [ 257.545366] unregister_netdevice: waiting for bar to become free. Usage count = 1 Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ar71xx: ag71xx: fix compile error when enabling debugKoen Vandeputte2019-03-051-6/+5
| | | | | | | | | | | | | | | | | | | | | | | Starting from kernel 4.5, phy_id needs to be fetched from a different location. not doing so results in this compile error: drivers/net/ethernet/atheros/ag71xx/ag71xx_phy.c: In function 'ag71xx_phy_connect_multi': drivers/net/ethernet/atheros/ag71xx/ag71xx_phy.c:133:35: error: 'struct mdio_device' has no member named 'phy_id' ag->mii_bus->mdio_map[phy_addr]->phy_id); ^ ./include/linux/printk.h:137:18: note: in definition of macro 'no_printk' printk(fmt, ##__VA_ARGS__); \ ^~~~~~~~~~~ drivers/net/ethernet/atheros/ag71xx/ag71xx.h:72:27: note: in expansion of macro 'pr_debug' #define DBG(fmt, args...) pr_debug(fmt, ## args) ^~~~~~~~ drivers/net/ethernet/atheros/ag71xx/ag71xx_phy.c:130:3: note: in expansion of macro 'DBG' DBG("%s: PHY found at %s, uid=%08x\n", ^~~ scripts/Makefile.build:326: recipe for target 'drivers/net/ethernet/atheros/ag71xx/ag71xx_phy.o' failed Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.104Koen Vandeputte2019-03-0536-276/+273
| | | | | | | | | | | | Refreshed all patches. Altered patches: - 332-arc-add-OWRTDTB-section.patch Compile-tested on: ar71xx, cns3xxx, imx6, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.161Koen Vandeputte2019-03-058-34/+34
| | | | | | | | | | | | Refreshed all patches. Altered patches: - 332-arc-add-OWRTDTB-section.patch Compile-tested on: ar7 Runtime-tested on: none Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: Add support for Ubiquiti Nanostation M (XW)Petr Štetiar2019-03-054-0/+48
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | CPU: AR9342 SoC RAM: 64 MB DDR2 Flash: 8 MB NOR SPI Ports: 2x100 MBit (24V PoE in, 24V PoE out), AR8236 switch WLAN: 2.4/5 GHz UART: 1 UART LEDs: Power, 2x Ethernet, 4x RSSI LEDs (orange, red, 2x green) Buttons: Reset Flashing instructions using recovery method over TFTP 1. Unplug the ethernet cable from the router. 2. Using paper clip press and hold the router's reset button. Make sure you can feel it depressed by the paper clip. Do not release the button until step 4. 3. While keeping the reset button pressed in, plug the ethernet cable back into the AP. Keep the reset button depressed until you see the device's LEDs flashing in upgrade mode (alternating LED1/LED3 and LED2/LED4), this may take up to 25 seconds. 4. You may release the reset button, now the device should be in TFTP transfer mode. 5. Set a static IP on your Computer's NIC. A static IP of 192.168.1.25/24 should work. 6. Plug the PoE injector's LAN cable directly to your computer. 7. Start tftp client and issue following commands: tftp> binary tftp> connect 192.168.1.20 tftp> put openwrt-ath79-generic-ubnt-nano-m-xw-squashfs-factory.bin Tested-by: Joe Ayers <ae6xe@arrl.net> Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: gmac: ar934x: Add parser for mii-gmac0-slavePetr Štetiar2019-03-051-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | While converting Nanostation M XW from current ar71xx code to ath79 I've hit one issue, where the ethernet networking wasn't working, so I was checking every bit in the networking setup path between ar71xx and ath79. I've came to the following code in ar71xx/mach-ubnt-xm.c: static void __init ubnt_xw_init(void) { ... ath79_setup_ar934x_eth_cfg(AR934X_ETH_CFG_MII_GMAC0 | AR934X_ETH_CFG_MII_GMAC0_SLAVE); ... } Where this code is setting AR934X_ETH_CFG_MII_GMAC0_SLAVE bit in AR934X_GMAC_REG_ETH_CFG register, but I couldn't find a way of setting this bit from DTS, so this patch adds `mii-gmac0-slave` DTS property which allows setting of this bit in `gmac-config`, which is then used in Nanostation M XW DTS. Tested-by: Joe Ayers <ae6xe@arrl.net> Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: qca955x: assert mdio/gmac reset togetherChuanhong Guo2019-03-051-10/+8
| | | | | | | | This allows resetting gmac registers during initialization. Also add compatible string for qca955x mdio to enable more mdio clock dividers. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: ar934x: assert mac/mdio reset together for gmac0Chuanhong Guo2019-03-051-6/+3
| | | | | | This allows resetting gmac registers during initialization. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: ag71xx: add support for optional mdio resetChuanhong Guo2019-03-052-1/+8
| | | | | | | | | | | | | | | | | | | | | | On ar933x and later chips, there are separated mac/mdio resets, but resetting the entire gmac block with register values requires both mac_reset and mdio_reset to be asserted together. Add support for optional mdio reset so that we can do a full reset if needed. This patch also replaced deprecated devm_reset_control_get for mac reset. To use this feature, the following is needed: 1. drop "simple-mfd" compatible to register mdio0 after gmac init so that mdio registers aren't reset after initialization. 2. move mdio reset from mdio-bus to its parent eth node. NOTE: This can't be applied on gmac1 with builtin switch since we haven't add a feature to defer probe if phy connection failed. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: ag71xx: register mdio using of_platform_populateChuanhong Guo2019-03-051-5/+12
| | | | | | | remove the hacky checking of "simple-mfd" compatible also add some comments explaining that piece of code. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: ag71xx-mdio: get reset control using devm apiChuanhong Guo2019-03-051-1/+1
| | | | Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: ag71xx: replace alloc_etherdev with devm_alloc_etherdevChuanhong Guo2019-03-051-22/+11
| | | | | | | | using the devm api makes the code simpler. also drop unneeded memory free from ag71xx_remove since they are allocated using devm apis. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: ag71xx: replace ag71xx_get_phy_if_mode_name() with phy_modes()Chuanhong Guo2019-03-051-22/+2
| | | | | | | | | phy_modes() in phy.h can convert PHY modes to string with supports for all available PHY modes. Also add a space in mode printing to make it look better. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* oxnas: pcie: model shared resource as external pcie-phy driverDaniel Golle2019-03-046-77/+226
| | | | | | | Refactor pcie-oxnas to have shared resources in syscon and new pcie-phy driver. Hopefully this revives PCIe... Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* oxnas: convert pcie to builtin_platform_driverDaniel Golle2019-03-041-21/+12
| | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* oxnas: restart: use register definitions from dt-bindingsDaniel Golle2019-03-031-60/+27
| | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* oxnas: cleanup and improve pcie driverDaniel Golle2019-03-031-274/+45
| | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* oxnas: add SoC restart driver for rebootDaniel Golle2019-03-033-23/+298
| | | | | | Refresh oxnas kernel config while at it. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* oxnas: cloudengines,pogoplug*: enable USB portsDaniel Golle2019-03-022-0/+17
| | | | | Reported-by: Jörg Fischer <fischer.loepsingen@yahoo.de> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-07 20:03:50 +0000