aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
* bcm27xx: import latest patches from the RPi foundationÁlvaro Fernández Rojas2021-02-18927-703/+41630
| | | | | | | | | bcm2708: boot tested on RPi B+ v1.2 bcm2709: boot tested on RPi 3B v1.2 and RPi 4B v1.1 4G bcm2710: boot tested on RPi 3B v1.2 bcm2711: boot tested on RPi 4B v1.1 4G Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* kernel: bump 5.4 to 5.4.99John Audia2021-02-1831-89/+87
| | | | | | | | | | Ran update_kernel.sh in a fresh clone without any existing toolchains. No manual changes needed. Build system: x86_64 Build-tested: bcm27xx/bcm2711 Signed-off-by: John Audia <graysky@archlinux.us>
* lantiq: fritz7320: enable USB power supplyMathias Kresin2021-02-181-0/+46
| | | | | | | | | | | | The USB ports if a FRIZZ!Box 7320 do not supply power to connected devices. Add the GPIOs enabling USB power as regulator, to enable USB power supply as soon as the USB driver is loaded. Fixes FS#3624 Signed-off-by: Mathias Kresin <dev@kresin.me>
* generic: don't lock when recursively deleting partitionsDavid Bauer2021-02-181-0/+24
| | | | | | | | When recursively deleting partitions, don't acquire the masters partition lock twice. Otherwise the process endy up in a deadlocked state. Signed-off-by: David Bauer <mail@david-bauer.net>
* generic: add various kernel 5.10 config symbolsDavid Bauer2021-02-181-0/+36
| | | | | | These symbols were unset when configuring for ath79. Signed-off-by: David Bauer <mail@david-bauer.net>
* mediatek: add support for Ubiquiti UniFi 6 LRDavid Bauer2021-02-186-2/+378
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- MediaTek MT7622 512MB DDR3 RAM 64M SPI-NOR Flash (Winbond W25Q512JV) MediaTek MT7622 802.11bgn 4T4R WMAC MediaTek MT7915 802.11ax 4T4R Marvell AQR1112 100/1000/2500 NBase-T PHY Holtek HT32F52241 LED controller Reset Switch UART ---- CPU UART0 at the pinout next to the Holtek MCU. Pinout (first pin next to SoC / MCU) 0 3V3 1 RX 2 TX 3 GND Settings are 115200 8N1. Opening the case ---------------- Opening the case is not a nice task, as itis glued together. Insert a flat knife between the front and back casing below the ethernet port. Open up a gap this way and insert a flat scredriver, remove the knife. Work your way around the casing by applying force to seperate the front and back casing. This losens the glue and opens the plastic clips. Be gentle, as these clips are very cheap and break quickly. Installation ------------ 1. Connect to the booted device at 192.168.1.20 using username/password "ubnt". 2. Transfer the OpenWrt sysupgrade image to the device using SCP. 3. Check the mtd partition number for bs / kernel0 / kernel1 $ cat /proc/mtd 4. Set the bootselect flag to boot from kernel0 $ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock6 5. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1 $ dd if=openwrt.bin of=/dev/mtdblock8 $ dd if=openwrt.bin of=/dev/mtdblock9 6. Reboot the device. It should boot into OpenWrt. Signed-off-by: David Bauer <mail@david-bauer.net>
* mediatek: add Ubiquiti LED driverDavid Bauer2021-02-185-0/+242
| | | | | | | | | | | Add a driver for controlling the RGB LED via Ubiquitis own "LEDBAR" LED controller based on the Holtek HT32F52241 MCU. This driver is initially used by the Ubiquiti UniFi 6 LR, however judging from FCC pictures the MCU is also found on the U6-Mesh as well as the U6-Extender. Signed-off-by: David Bauer <mail@david-bauer.net>
* bcm63xx: add kernel 5.10 supportÁlvaro Fernández Rojas2021-02-17141-0/+21640
| | | | | | Runtime-tested on Comtrend AR-5387un. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* kernel: update kernel 5.10 to 5.10.16Daniel Golle2021-02-172-2/+2
| | | | | | Compile and runtime-tested on mediatek/mt7622 Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: 5.10: refresh patchesAdrian Schmutzler2021-02-165-36/+41
| | | | Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: 5.10: add missing partitions doc syntax commitAdrian Schmutzler2021-02-161-0/+324
| | | | | | | This patch has been added to 5.4, but not been copied to 5.10: 7495acb55573 ("kernel: backport mtd commit converting partitions doc syntax") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: hack-5.10: make UDP tunneling user-selectableAdrian Schmutzler2021-02-161-0/+11
| | | | | | | | | | | | | | | | This applies another patch from 5.4 to 5.10 as well: de09355f74c3 ("kernel/hack-5.4: make UDP tunneling user-selectable") UDP tunneling support isn't user-selectable, but it's required by WireGuard which is, for the time being, an out-of-tree module. We currently work around this issue by selecting an unrelated module which depends on UDP tunnelling (VXLAN). This is inconvenient, as it implies this unrelated module needs to be built-in when doing a monolithic build. Fix this inconvenience by making UDP tunneling user-selectable in the kernel configuration. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: 5.4: fix .patch file extensionAdrian Schmutzler2021-02-161-0/+0
| | | | | | | File extension was truncated for pending-5.4/770-11-net-ethernet-mtk_eth_soc-avoid-rearming-interrupt-if.pa Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: 5.10: fix busy wait loop in mediatek PPE codeAdrian Schmutzler2021-02-161-1/+1
| | | | | | | | | | | | | | Reapply changes added to 5.4 but not copied to 5.10: 3da4acaa7bba ("kernel: fix busy wait loop in mediatek PPE code") The intention is for the loop to timeout if the body does not succeed. The current logic calls time_is_before_jiffies(timeout) which is false until after the timeout, so the loop body never executes. time_is_after_jiffies(timeout) will return true until timeout is less than jiffies, which is the intended behavior here. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* generic: ar8216: update version switch for of_get_phy_mode fixAdrian Schmutzler2021-02-161-2/+2
| | | | | | | | | | | | | Kernel has changed the of_get_phy_mode API in commit 0c65b2b90d13 ("net: of_get_phy_mode: Change API to solve int/unit warnings"). This is already included in kernel 5.5, so fix the version switch (though this will not actually matter for the versions we support). Similar driver adjustments to account for the API change will probably be necessary to various other local drivers. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* generic: ar8216: fix kernel 5.10 compile errorDavid Bauer2021-02-161-0/+8
| | | | Signed-off-by: David Bauer <mail@david-bauer.net>
* kernel: add linux 5.10 supportFelix Fietkau2021-02-16153-1/+31974
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* bcm4908: add bcm_sf2 fixes for the 5th GPHYRafał Miłecki2021-02-162-0/+76
| | | | | | | This allows using the last integrated PHY (and so e.g. WAN port on the ASUS GT-AC5300). Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm4908: fix GPIOs support by limiting them to 64Rafał Miłecki2021-02-151-0/+23
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm4908: use DTS patches sent upstreamRafał Miłecki2021-02-155-33/+145
| | | | | | | | There are 2 new patches: 1. Netgear R8000P switch ports 2. Netgear R8000P LEDs Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm4908: add USB packages to the DEFAULT_PACKAGESRafał Miłecki2021-02-151-0/+2
| | | | | | | All known 41 BCM4908 devices have USB ports so it makes sense to include those packages by default. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm4908: fix backport of PMB driverRafał Miłecki2021-02-151-0/+8
| | | | | | | Missing Makefile change was preventing kernel from actually compiling the driver. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: drop ofpart patch dropped from upstream mtd treeRafał Miłecki2021-02-156-236/+653
| | | | | | It stopped ofpart_parser_init() from being called Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: backport "ofpart" mtd parser upstream quirks supportRafał Miłecki2021-02-156-29/+77
| | | | | | | | | | This adds quirks support to the "ofpart" parser. It's required to support fixed partitions that require some extra logic. Right now only BCM4908 binding is supported (BCM4908 requires detecting currently used "firmware" partition). Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: fix busy wait loop in mediatek PPE codeIlya Lipnitskiy2021-02-151-1/+1
| | | | | | | | | | | The intention is for the loop to timeout if the body does not succeed. The current logic calls time_is_before_jiffies(timeout) which is false until after the timeout, so the loop body never executes. time_is_after_jiffies(timeout) will return true until timeout is less than jiffies, which is the intended behavior here. Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
* ramips: mark toggle input on EX6150 as a switchKurt Roeckx2021-02-151-0/+1
| | | | | | | | | The Netgear EX6150 has an Access Point/Extender switch. Set it as an EV_SW. Otherwise when it's set to Access Point, it will trigger failsafe mode during boot. Fixes: FS#3590 Signed-off-by: Kurt Roeckx <kurt@roeckx.be>
* Revert "imx6: bootscript-apalis: make it working on v2021.01 release"Petr Štetiar2021-02-141-4/+2
| | | | | | | | This reverts commit 4968fc8fb110612018af3ba2836be1b4744346e2 as the bump to v2021.01 needs swig on the host for pylibfdt which is needed by dtoc tool to generate .h/.c files from DTBs in SPL for mx6cuboxi_config. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* target: fix copying of licenses for SDK/toolchainAdrian Schmutzler2021-02-142-2/+6
| | | | | | | | | | | | | | | The SDK and target/toolchain copy the license file into their directories. During the rename/move from LICENSE to a LICENSES folder, this has not been updated. Update it now, and include the new COPYING file. While at it, improve formatting/indent. Fixes: 882e3014610b ("LICENSES: include all used licenses in LICENSES directory") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: fix factory image generation for Netgear and Zyxel boardsPaul Fertser2021-02-143-4/+2
| | | | | | | | | | | | | The factory images need to embed specific IDs to pass verification with the OEM firmware (including TFTP recovery), so they need to be per-device variables. Fixes: ab1584a797ad ("ath79: netgear: trim down uImage customisations") Fixes: 459c8c9ef816 ("ath79: add support for ZyXEL NBG6616") Reported-by: Marcin Juszkiewicz <marcin-openwrt@juszkiewicz.com.pl> Signed-off-by: Paul Fertser <fercerpav@gmail.com> [minor commit message adjustments, sort DEVICE_VARS] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mvebu: espressobin: drop COMPHY removement patchTomasz Maciej Nowak2021-02-142-53/+0
| | | | | | | | | | There are proper workarounds merged to 5.4 stable tree for ESPRESSObin boards with older bootloader: 4e1a23779bde ("ata: ahci: mvebu: Make SATA PHY optional for Armada 3720") 40af962eb1d4 ("usb: host: xhci: mvebu: make USB 3.0 PHY optional for Armada 3720") Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
* ramips: manage low reset linesSander Vanheule2021-02-141-0/+47
| | | | | | | | | | | | The bootloader of a number of recent TP-Link devices does not properly initialise the MT7621's internal switch when booting from flash. To enable the mt7530 driver to clear the reset on the switch, the ramips reset controller must be allowed to toggle these. Backport upstream commit 3f9ef7785a9c from mips-next to allow control of the "mcm" reset line. Signed-off-by: Sander Vanheule <sander@svanheule.net>
* imx6: bootscript-apalis: make it working on v2021.01 releasePetr Štetiar2021-02-141-2/+4
| | | | | | | | | Upstream in commit 8b9c0cb46471 ("apalis_imx6: boot env configuration updates") removed emmc legacy wrappers, but so far didn't included any replacements. Fix it by simply defining the missing variables and UUID gathering directly into the boot script. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* bcm4908: refresh patchesAdrian Schmutzler2021-02-132-503/+1534
| | | | | | | | | | Our patch refresh tool creates quite a big diff for these patches, as it does not use rename syntax. Push the refresh separately so it does not pollute the next kernel bump. This is a purely cosmetic change. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: fix chip used for Meraki MR12 caldata_extractMartin Kennedy2021-02-131-3/+3
| | | | | | | | | | | | | The original setup fails to trigger ART calibration data extraction for the AR9287. Instead, it would only have extracted calibration data for an internal WMAC chip which is not present on this board. Fixes: 55d2db0e8ceb ("ath79: add support for Meraki MR12") Signed-off-by: Martin Kennedy <hurricos@gmail.com> [commit title/message facelift] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove factory image for TP-Link Archer C2 v1Stijn Segers2021-02-131-0/+1
| | | | | | | | | | | | | | | | | | | Initial commit 8375623a0640 ("ramips: add support for TP-Link Archer C2") contains detailed installation instructions, which do not mention a factory image. From what I can see, no support to install OpenWrt through the vendor web interface has been added since. The factory image is also conspicuously absent from the device page in the wiki. Yet, it is available for download. I bricked my Archer C2 loading the factory image through the web UI. Serial showed this error during bootloop: Uncompressing Kernel Image ... LZMA ERROR 1 - must RESET board to recover This patch disables the undocumented factory image so users won't get tricked into thinking easy web UI flashing actually works. Signed-off-by: Stijn Segers <foss@volatilesystems.org>
* bcm4908: fix handling Ethernet frames of size 1506 - 1514Rafał Miłecki2021-02-121-0/+113
| | | | | | MTU needs to be explicitly set as default value is too low. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm4908: use upstream accepted Ethernet driver patchesRafał Miłecki2021-02-1212-156/+1128
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* realtek: add support for Netgear GS108T v3Michael Mohr2021-02-122-0/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Netgear GS108T v3 is an 8 port gigabit switch with PoE-PD support on port 1. The two prior versions were built using eCos and are not currently compatible with OpenWRT. The GS108T v3 is quite similar to both the GS110TPP v1 and GS110TP v3, all of which use the same firmware image from Netgear. For this reason, the device tree is identical aside from the model and compatible values. All of the above feature a dual firmware layout, referred to as Image0 and Image1 in the Netgear firmware. Hardware specification ---------------------- * RTL8380M SoC, 1 MIPS 4KEc core @ 500MHz * 128MB DDR3-1600 DRAM (Winbond W631GG8MB-12) * 32MB 3v NOR SPI Flash (Macronix MX25L25635F or Winbond W25Q256JVFIQ) * RTL8231 GPIO extender to control the LEDs and the reset button * 8 x 10/100/1000BASE-T ports, internal PHY (RTL8218B) * UART (115200 8N1) via unpopulated standard 0.1" pin header marked J1 * Power is supplied via a 12V 1A barrel connector or 802.3af UART pinout ----------- J1 | [o]ooo ^ ||`------ GND | |`------- RX [TX out of the serial adapter] | `-------- TX [RX into the serial adapter] `---------- Vcc (3V3) [the square pin] The through holes are filled with PB-free solder which melts at 375C. They can also be drilled using a 0.9mm bit. Build configuration ------------------- * Target System: Realtek MIPS * Target Profile: Netgear GS108T v3 * Target Images -> ramdisk -> Compression: lzma * Disable other target images Boot initramfs image from U-Boot -------------------------------- 1. Press the Escape key at the `Hit Esc key to stop autoboot` prompt 2. Init network with `rtk network on` command 3. Load image with `tftpboot 0x8f000000 openwrt-realtek-generic-netgear_gs108t-v3-initramfs-kernel.bin` command 4. Boot the image with `bootm` command The switch defaults to IP 192.168.1.1 and tries to fetch the image via TFTP from 192.168.1.111. Updating the installed firmware ------------------------------- The OpenWRT ramdisk image can be flashed directly from the Netgear UI. The Image0 slot should be used in order to enable sysupgrade. As with similar switches, changing the active boot partition can be accomplished in U-Boot as follows: 1. Press the Escape key at the `Hit Esc key to stop autoboot` prompt 2. Run `setsys bootpartition {0|1}` to select the boot partition 3. Run `savesys` followed by `boota` to proceed with the boot process Signed-off-by: Michael Mohr <akihana@gmail.com>
* realtek: refactor the Netgear GS110TPP v1 device treeMichael Mohr2021-02-122-225/+139
| | | | | | | | | | | | | | | | | | | Move most of the GS110TPP v1 device tree into a dtsi so that it can be shared with the GS108T v3. Additionally: * Use macros to simplify the ethernet and switch definitions * Zero-pad the offsets and sizes in the partition map to 8 digits each The spi-max-frequency value has been changed from 10MHz to 50MHz based on an analysis of the relevant datasheets. The current driver doesn't use this property, as the clock speed is fixed. However, it's required for this type of DT node, so that's why it's present here. The firmware partition has been split in half, since this is how the stock firmware uses it. This can be used to easily revert to a stock firmware if one is written to the second image area. Signed-off-by: Michael Mohr <akihana@gmail.com>
* realtek: add and use netgear_nge for the GS110PP v1Michael Mohr2021-02-121-6/+12
| | | | | | | | The netgear_nge device will be shared between the GS108T v3 (to be added in a later commit) and the GS110PP v1. It also enables LZMA compression for the ramdisk image. Signed-off-by: Michael Mohr <akihana@gmail.com>
* ath79: fix USB power GPIO for TP-Link TL-WR810N v1Adrian Schmutzler2021-02-111-1/+1
| | | | | | | | | | | | | | | | | | The TP-Link TL-WR810N v1 is known to cause soft-brick on ath79 and work fine for ar71xx [1]. On closer inspection, the only apparent difference is the GPIO used for the USB regulator, which deviates between the two targets. This applies the value from ar71xx to ath79. Tested successfully by a forum user. [1] https://forum.openwrt.org/t/tp-link-tl-wr810n-v1-ath79/48267 Fixes: cdbf2de77768 ("ath79: Add support for TP-Link WR810N") Fixes: FS#3522 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for ELECOM WRC-1167FSINAGAKI Hiroshi2021-02-114-0/+200
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ELECOM WRC-1167FS is a 2.4/5 GHz band 11ac (WiFi-5) router, based on MT7628AN. Specification: - SoC : MediaTek MT7628AN - RAM : DDR2 64 MiB (NT5TU32M16FG-AC) - Flash : SPI-NOR 16 MiB (W25Q128JVSIQ) - WLAN : 2.4/5 GHz 2T2R - 2.4 GHz : MediaTek MT7628AN (SoC) - 5 GHz : MediaTek MT7612E - Ethernet : 10/100 Mbps x2 - Switch : MT7628AN (SoC) - LEDs/Keys : 6x, 3x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J1: 3.3V, GND, TX, RX from "J1" marking - 57600n8 - Power : 12 VDC, 1 A Flash instruction using factory image: 1. Boot WRC-1167FS normally 2. Access to "http://192.168.2.1/" and open firmware update page ("ファームウェア更新") 3. Select the OpenWrt factory image and click apply ("適用") button to perform firmware update 4. Wait ~120 seconds to complete flashing Notes: - Last 0x800000 (8 MiB) in SPI-NOR flash is not used on stock firmware - Additional padding in factory image is required to avoid incomplete flashing on stock firmware MAC addresses: - LAN : BC:5C:4C:xx:xx:68 (Config, ethaddr (text) / Factory, 0x28 (hex)) - WAN : BC:5C:4C:xx:xx:69 (Config, wanaddr (text) / Factory, 0x22 (hex)) - 2.4GHz: BC:5C:4C:xx:xx:6A (Config, rmac (text) / Factory, 0x4 (hex)) - 5GHz : BC:5C:4C:xx:xx:6B (Config, rmac2 (text) / Factory, 0x8004 (hex)) Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* kernel: bump 5.4 to 5.4.97John Audia2021-02-1115-33/+24
| | | | | | | | | | | | | | | | | | | | | | | | Ran update_kernel.sh in a fresh clone without any existing toolchains. Manually rebased: bcm27xx 950-0267-xhci-add-quirk-for-host-controllers-that-don-t-updat.patch bcm53xx 180-usb-xhci-add-support-for-performing-fake-doorbell.patch layerscape 302-dts-0008-arm64-dts-ls1046a-accumulated-change-to-ls1046a-boar.patch 820-usb-0016-MLK-16735-usb-host-add-XHCI_CDNS_HOST-flag.patch 820-usb-0018-MLK-18794-1-usb-host-xhci-add-.bus_suspend-override.patch Build system: x86_64 Build-tested: bcm27xx/bcm2711, ipq806x/R7800 Run-tested: ipq806x/R7800 No dmesg regressions/everything functional. Signed-off-by: John Audia <graysky@archlinux.us> [remove quilt comment, fix/adjust 820-usb-* layerscape patches] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* at91: use SPDX license identifiers on DTS filesAdrian Schmutzler2021-02-105-10/+10
| | | | | | Use SPDX license tags to allow machines to check licenses. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* target: use SPDX license identifiers on scriptsAdrian Schmutzler2021-02-1014-69/+14
| | | | | | Use SPDX license tags to allow machines to check licenses. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* target: use SPDX license identifiers on MakefilesAdrian Schmutzler2021-02-10139-555/+203
| | | | | | Use SPDX license tags to allow machines to check licenses. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* bcm4908: update Ethernet driverRafał Miłecki2021-02-104-178/+179
| | | | | | Use the latest version sent upsteram. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ramips: add support for Cudy WR1300Andrew Pikler2021-02-092-0/+205
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - SoC: MediaTek MT7621AT - RAM: 128 MB (DDR3) - Flash: 16 MB (SPI NOR) - WiFi: MediaTek MT7603E, MediaTek MT7612E - Switch: 1 WAN, 4 LAN (Gigabit) - Ports: 1 USB 3.0 - Buttons: Reset, WPS - LEDs: Power, System, Wan, Lan 1-4, WiFi 2.4G, WiFi 5G, WPS, USB - Power: DC 12V 1A tip positive UART Serial: 115200 baud Located on unpopulated 4 pin header near J4: J4 [o] Rx [o] Tx [o] GND [ ] Vcc - Do not connect Installation: Download and flash the manufacturer's built OpenWRT image available at http://www.cudytech.com/openwrt_software_download Install the new OpenWRT image via luci (System -> Backup/Flash firmware) Be sure to NOT keep settings. The force upgrade may need to be checked due to differences in router naming conventions. Recovery: - Loads only signed manufacture firmware due to bootloader RSA verification - serve tftp-recovery image as /recovery.bin on 192.168.1.88/24 - connect to any lan ethernet port - power on the device while holding the reset button - wait at least 8 seconds before releasing reset button for image to download - See http://www.cudytech.com/newsinfo/547425.html MAC addresses as verified by OEM firmware: use address source LAN *:f0 label WAN *:f1 label + 1 2g *:f0 label 5g *:f2 label + 2 The label MAC address is found in bdinfo 0xde00. Signed-off-by: Andrew Pikler <andrew.pikler@gmail.com>
* ath79: add support for D-Link DAP-3662 A1Sebastian Schaper2021-02-097-5/+128
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: * QCA9557, 16 MiB Flash, 128 MiB RAM, 802.11n 2T2R * QCA9882, 802.11ac 2T2R * 2x Gigabit LAN (1x 802.11af PoE) * IP68 pole-mountable outdoor case Installation: * Factory Web UI is at 192.168.0.50 login with 'admin' and blank password, flash factory.bin * Recovery Web UI is at 192.168.0.50 connect network cable, hold reset button during power-on and keep it pressed until uploading has started (only required when checksum is ok, e.g. for reverting back to oem firmware), flash factory.bin After flashing factory.bin, additional free space can be reclaimed by flashing sysupgrade.bin, since the factory image requires some padding to be accepted for upgrading via OEM Web UI. Both ethernet ports are set to LAN by default, matching the labelling on the case. However, since both GMAC Interfaces eth0 and eth1 are connected to the switch (QCA8337), the user may create an additional 'wan' interface as desired and override the vlan id settings to map br-lan / wan to either the PoE or non-PoE port, depending on the individual scenario of use. So, the LAN and WAN ports would then be connected to different GMACs, e.g. config interface 'lan' option ifname 'eth0.1' ... config interface 'wan' option ifname 'eth1.2' ... config switch_vlan option device 'switch0' option vlan '1' option ports '1 0t' config switch_vlan option device 'switch0' option vlan '2' option ports '2 6t' Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net> [add configuration example] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for JCG Y2Chukun Pan2021-02-094-7/+152
| | | | | | | | | | | | | | | | | | | | | | | | JCG Y2 is an AC1300M router Hardware specs: SoC: MediaTek MT7621AT Flash: Winbond W25Q128JVSQ 16MiB RAM: Nanya NT5CB128M16 256MiB WLAN: 2.4/5 GHz 2T2R (1x MediaTek MT7615) Ethernet: 10/100/1000 Mbps x5 LED: POWER, INTERNET, 2.4G, 5G Button: Reset Power: DC 12V,1A Flash instructions: Upload factory.bin in stock firmware's upgrade page. MAC addresses map: 0x0004 *:c8 wlan2g/wlan5g/label 0xe000 *:c7 lan 0xe006 *:c6 wan Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-02 22:21:30 +0000