aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
...
* kernel: bump 4.19 to 4.19.37Koen Vandeputte2019-05-028-38/+38
| | | | | | | | | | | | | Refreshed all patches. Altered patches: - 150-bridge_allow_receiption_on_disabled_port.patch - 201-extra_optimization.patch Compile-tested on: cns3xxx, imx6 Runtime-tested on: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.114Koen Vandeputte2019-05-0237-221/+152
| | | | | | | | | | | | | | | | Refreshed all patches. Altered patches: - 150-bridge_allow_receiption_on_disabled_port.patch - 201-extra_optimization.patch Remove upstreamed: - 022-0006-crypto-crypto4xx-properly-set-IV-after-de-and-encryp.patch Compile-tested on: ar71xx, cns3xxx, imx6, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.171Koen Vandeputte2019-05-025-15/+17
| | | | | | | | | | | | | Refreshed all patches. Altered patches: - 150-bridge_allow_receiption_on_disabled_port.patch - 201-extra_optimization.patch Compile-tested on: ar7 Runtime-tested on: none Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: add missing symbol in 4.19 configKoen Vandeputte2019-04-291-0/+1
| | | | | | Intel AtomISP2 dummy / power-management driver (INTEL_ATOMISP2_PM) [N/m/y/?] (NEW) Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: fix regression on 4.19 with ↵Felix Fietkau2019-04-271-0/+9
| | | | | | | | | | | 613-netfilter_optional_tcp_window_check.patch (FS#2253) Since ct->proto.tcp.last_win isn't updated when nf_ct_tcp_no_window_check is enabled, the retransmission timeout check needs to be bypassed. Based on patch by Rob Mosher Signed-off-by: Felix Fietkau <nbd@nbd.name>
* sdk: fix building external modules when CONFIG_STACK_VALIDATION=yYousong Zhou2019-04-261-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The option is at the moment enabled for x86/64. The selection chain should be config RETPOLINE select STACK_VALIDATION if HAVE_STACK_VALIDATION config x86 select HAVE_STACK_VALIDATION if X86_64 cryptdev-linux: make[4]: Entering directory '/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/cryptodev-linux-cryptodev-linux-1.10' make -C /store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/linux-4.14.113 M=/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/cryptodev-linux-cryptodev-linux-1.10 ARCH=x86 CROSS_COMPILE=x86_64-openwrt-linux-musl- modules make[5]: Entering directory '/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/linux-4.14.113' make[6]: *** No rule to make target '/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/cryptodev-linux-cryptodev-linux-1.10/ioctl.o', needed by '/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/cryptodev-linux-cryptodev-linux-1.10/cryptodev.o'. Stop. Makefile:1533: recipe for target '_module_/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/cryptodev-linux-cryptodev-linux-1.10' failed Open vSwitch intree kmods make[7]: Entering directory '/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/openvswitch-2.11.0/datapath/linux' make -C /store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/linux-4.14.111 ARCH=x86 M=/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/openvswitch-2.11.0/datapath/linux modules make[8]: Entering directory '/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/linux-4.14.111' make[9]: *** No rule to make target 'tools/objtool/objtool', needed by '/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/openvswitch-2.11.0/datapath/linux/actions.o'. Stop. Makefile:1533: recipe for target '_module_/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/openvswitch-2.11.0/datapath/linux' failed make[8]: *** [_module_/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/openvswitch-2.11.0/datapath/linux] Error 2 make[8]: Leaving directory '/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/linux-4.14.111' Reference: builddeb: include objtool binary in headers package, https://patchwork.kernel.org/patch/9014071/ Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* ar71xx: add support for Mikrotik RouterBOARD 2011UiAS-2HnD r2Koen Vandeputte2019-04-234-3/+11
| | | | | | This board got a new hardware revision, without any change in functionality. Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.19 to 4.19.36Koen Vandeputte2019-04-232-3/+3
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx, imx6 Runtime-tested on: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.113Koen Vandeputte2019-04-231-4/+4
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx, imx6 Runtime-tested on: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.170Koen Vandeputte2019-04-231-2/+2
| | | | | | | | | Refreshed all patches. Compile-tested on: ar7 Runtime-tested on: none Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.19 to 4.19.35Koen Vandeputte2019-04-227-29/+23
| | | | | | | | | | | | | | | Refreshed all patches. Fixes: - CVE-2019-3887 New symbol: - CONFIG_LDISC_AUTOLOAD Compile-tested on: cns3xxx, imx6 Runtime-tested on: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.112Koen Vandeputte2019-04-228-18/+12
| | | | | | | | | | | | Refreshed all patches. New symbol: - CONFIG_LDISC_AUTOLOAD Compile-tested on: ar71xx, cns3xxx, imx6, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.169Koen Vandeputte2019-04-222-1/+3
| | | | | | | | | | | | | Refreshed all patches. New symbols: - CONFIG_LDISC_AUTOLOAD - CONFIG_PPC_BARRIER_NOSPEC Compile-tested on: ar7 Runtime-tested on: none Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* armvirt64: enable qemu drm driversLucian Cristian2019-04-181-0/+4
| | | | | | | adds the qemu video drivers and also fixes the build failure introduced with drm-kms-helper Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* kernel: add missing drm symbolLucian Cristian2019-04-183-0/+3
| | | | | | dependency introduced with module drm-kms-helper Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* lantiq: tdw90x0: Fix WLAN LED on TP-Link W8970 v1.2 (FS#2232)Petr Štetiar2019-04-171-0/+1
| | | | | | | | | | This patch fixes disfunctional WLAN LED on TP-Link W8970. The LED was reported working in the CC release[1], but doesn't work anymore in 18.06.2. 1. https://github.com/openwrt/chaos_calmer/commit/420cb24d41fcd650795f09d2b26e0e1d2cf21165 Tested-by: Damian Janarek <dzanar18@o2.pl> Signed-off-by: Petr Štetiar <ynezz@true.cz>
* layerscape: unbreak ehci-fsl interaction with mpc85xxChristian Lamparter2019-04-151-1/+1
| | | | | | | | | | Both targets have their own idea of how to use ehci-fsl. This patch reverts part of commit 68b8d3b0796d ("kernel: usb: add FSL EHCI package") and moves ehci-fsl back into kmod-usb2, while also making it hopefully useable for the mpc85xx target. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* mpc85xx: disable bricking TL-WDR4900v1 imagesChristian Lamparter2019-04-151-1/+1
| | | | | | | | | | | | | | | | | | The current mpc85xx build is failing because the TL-WDR4900v1 kernel image no longer fits into the partition. Extending the kernel is not possible without updating u-boot's kernel loader commands. This patch disables the WDR4900v1 until the kernel image size issue is fixed so the buildbot can still compile the Sophos RED 15w Rev.1 . Installing the WDR4900v1 images would cause the routers to get bricked. For the discussion, please go to: <https://github.com/openwrt/openwrt/pull/1773> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kernel: MIPS: perf: ath79: Fix perfcount IRQ assignmentPetr Štetiar2019-04-152-0/+234
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently it's not possible to use perf on ath79 due to genirq flags mismatch happening on static virtual IRQ 13 which is used for performance counters hardware IRQ 5. On TP-Link Archer C7v5: CPU0 2: 0 MIPS 2 ath9k 4: 318 MIPS 4 19000000.eth 7: 55034 MIPS 7 timer 8: 1236 MISC 3 ttyS0 12: 0 INTC 1 ehci_hcd:usb1 13: 0 gpio-ath79 2 keys 14: 0 gpio-ath79 5 keys 15: 31 AR724X PCI 1 ath10k_pci $ perf top genirq: Flags mismatch irq 13. 00014c83 (mips_perf_pmu) vs. 00002003 (keys) On TP-Link Archer C7v4: CPU0 4: 0 MIPS 4 19000000.eth 5: 7135 MIPS 5 1a000000.eth 7: 98379 MIPS 7 timer 8: 30 MISC 3 ttyS0 12: 90028 INTC 0 ath9k 13: 5520 INTC 1 ehci_hcd:usb1 14: 4623 INTC 2 ehci_hcd:usb2 15: 32844 AR724X PCI 1 ath10k_pci 16: 0 gpio-ath79 16 keys 23: 0 gpio-ath79 23 keys $ perf top genirq: Flags mismatch irq 13. 00014c80 (mips_perf_pmu) vs. 00000080 (ehci_hcd:usb1) This problem is happening, because currently statically assigned virtual IRQ 13 for performance counters is not claimed during the initialization of MIPS PMU during the bootup, so the IRQ subsystem doesn't know, that this interrupt isn't available for further use. So this patch fixes the issue by simply booking hardware IRQ 5 for MIPS PMU. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* Revert "ath79: Add WPS button to TP-Link Archer C7v5"Petr Štetiar2019-04-141-7/+0
| | | | | | | Reverting this commit as I've missed the fact, that the button is already present in the included DTSI file. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: add support for Rakwireless RAK633Eike Feldmann2019-04-144-0/+115
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It's OEM module with 2*26 pin header, similar to LinkIt Smart 7688 or Vocore2. Specification: CPU: MT7628 580 MHz. MIPS 24K RAM: 64 MB Flash: 8 MB WIFI: 802.11n/g/b 20/40 MHz USB: 1x Port USB 2.0 Ethernet: 5 Port ethernet switch UART: 2x Installation: Use the installed uboot Bootloader. Connect a serial cable to serialport 0. Turn power on. Choose the option: "Load system code then write to Flash via TFTP". Choose the local device IP and the TFTP server IP and the file name of the system image. After if the Bootloader will copy the image to the local flash. Notes: The I2C Kernel module work not correctly. You can send and receive data. But the command i2cdetect doesn’t work. FS#845 Signed-off-by: Eike Feldmann <eike.feldmann@outlook.com> [commit subject and message touches, DTS whitespace fixes, wifi LED rename, pinctrl fixes, network settings fixes, lan/wmac mac addresses, removed i2c kernel modules] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: add support for GL.iNet VIXMINIDavid Bauer2019-04-133-0/+123
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SoC: MediaTek MT7628NN RAM: 64M DDR2 (Etron EM68B16CWQD-25H) FLASH: 8M (Winbond W25Q64JVSIQ) LED: Power - WLAN BTN: Reset UART: 115200 8N1 TX and RX are labled on the board as pads next to the SoC Installation via web-interface ------------------------------ 1. Visit the web-interface at 192.168.8.1 Note: The ethernet port is by default WAN. So you need to connect to the router via WiFi 2. Navigate to the Update tab on the left side. 3. Select "Local Update" 4. Upload the OpenWrt sysupgrade image. Note: Make sure you select not to preserve the configuration. Installation via U-Boot ----------------------- 1. Hold down the reset button while powering on the device. Wait for the LED to flash 5 times. 2. Assign yourself a static IPv4 in 192.168.1.0/24 3. Upload the OpenWrt sysupgrade image at 192.168.1.1. Signed-off-by: David Bauer <mail@david-bauer.net>
* mpc85xx: generic: Check kernel size for the TL-WDR4900Pawel Dembicki2019-04-131-0/+1
| | | | | | | | | | | TP-Link TL-WDR 4900 have u-boot with read-only env. Boot command read only 0x29F000 data from flash. Bigger images causes crc error. It can't be changed. This patch add kernel size checking. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [utilize KERNEL_SIZE]
* mpc85xx: clean up device package selectionDavid Bauer2019-04-131-4/+2
| | | | | | | Remove wireless and USB packages from the device-specific package selection as they are already selected by the target itself. Signed-off-by: David Bauer <mail@david-bauer.net>
* mpc85xx: remove USB support from kernelDavid Bauer2019-04-133-15/+1
| | | | | | | | | | | | This removes USB support from the compiled kernel. Because of this, the kernel is just small enough for the TP-Link WDR4900 to boot the resulting kernel. This is necessary to support the WDR4900 in the upcoming 19.xx release. In the long run, this should be fixed with a second stage bootloader, as the vendor bootloader only loads the first 2684k bytes. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: remove unnecessary packages from I-O DATA ETG3-RINAGAKI Hiroshi2019-04-131-0/+1
| | | | | | | | I-O DATA ETG3-R is a wired router. So wireless-related packages are unnecessary and remove those packages from default configuration to reduce flash usage. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: add TP-Link WR842N v3Sven Roederer2019-04-134-1/+181
| | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the TP-Link WR842N v3 which is already supported on ar71xx target (0b45bec22c59cc6e6b2fa71dc9a88386c5587132). Specification: * SoC: QCA9533 ver 2 rev 0 * 16 MB Flash (gd25q128) * 64 MB RAM * 1 WAN 10/100 MBit/s (blue connector) * 4 LAN 10/100 MBit/s (AR8229; 4 ports; yellow connectors) * Atheros AR9531 (2,4GHz, two fixed antennas) * USB * Reset / WPS button * WiFi button (rf kill) * 8 green leds; 1 red/green led * serial console (115200 8N1, according to the OpenWrt-wiki some soldering is needed) Installation: * flash via vendor WebUI (the filename must not exceed certain length) * sysupgrade from installed OpenWrt (also ar71xx) Thanks to Holger Drefs for providing the hardware Tested-by: @kofec (github) Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
* ramips: fix pinctrl to allow hardware i2c on WRTNODE2RDaniel Golle2019-04-111-1/+11
| | | | | | | | Instead of assigning I2C pins as GPIOs by default, leave it up to the user whether to install kmod-i2c-mt7621 and use them for hardware I2C instead. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: move and replace accepted patchDaniel Golle2019-04-111-12/+11
| | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* imx6: bump sdma firmware to 3.4Koen Vandeputte2019-04-091-0/+0
| | | | Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: add support for Netgear EX6400 and EX7300Daniel Gimpelevich2019-04-097-0/+280
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This is sold as a dual-band 802.11ac range extender. It has a sliding switch for Extender mode or Access Point mode, a WPS button, a recessed Reset button, a hard-power button, and a multitude of LED's, some multiplexed via an NXP 74AHC164D chip. The internal serial header pinout is Vcc, Tx, Rx, GND, with GND closest to the corner of the board. You may connect at 115200 bps, 8 data bits, no parity, 1 stop bit. Specification: - System-On-Chip: QCA9558 - CPU/Speed: 720 MHz - Flash-Chip: Winbond 25Q128FVSG - Flash size: 16 MiB - RAM: 128 MiB - Wireless No1: QCA9558 on-chip 2.4GHz 802.11bgn, 3x3 - Wireless No2: QCA99x0 chip 5GHz 802.11an+ac, 4x4 - PHY: Atheros AR8035-A Installation: If you can get to the stock firmware's firmware upgrade option, just feed it the factory.img and boot as usual. As an alternative, TFTP the factory.img to the bootloader. Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> [whitespace fix in DTS and reorder of make variables] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: remove more duplicate image build variablesDaniel Gimpelevich2019-04-093-22/+18
| | | | | | | | | Remove Netgear-specific image build variables which are set to the same value. Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> [reordering of variables, removed stray newline] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* sunxi: Remove already applied patchHauke Mehrtens2019-04-081-214/+0
| | | | | | | This patch is already included in kernel v4.19.31. Fixes: 8df12d76c642 ("kernel: bump 4.19 to 4.19.34") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ar71xx: Correct MAC address for WAN interface of Archer C7 v5Adrian Schmutzler2019-04-081-0/+4
| | | | | | | | | | | This device shares the network config with v4, thus the WAN MAC also needs to be fixed the same way. However, the partition where the MAC address resides has been changed. Based on: https://github.com/openwrt/openwrt/pull/1726 Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ar71xx: Add "info" partition for TP-Link Archer C7 v5Adrian Schmutzler2019-04-081-1/+1
| | | | | | | | | | | | | | This adds the "info" MTD partition, as it is specified in the ath79 DTS: https://github.com/openwrt/openwrt/blob/master/target/linux/ath79/dts/qca9563_tplink_archer-c7-v5.dts#L35 This is required to set the WAN MAC address, as it is build based on the LAN MAC address, which in turn has to be read from the "info" partition: https://github.com/openwrt/openwrt/blob/master/target/linux/ath79/dts/qca9563_tplink_archer-c7-v5.dts#L35 Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Add WPS button to TP-Link Archer C7v5Petr Štetiar2019-04-081-0/+7
| | | | | | | This patch adds currently missing support for the WPS button on TP-Link Archer C7v5. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: Correct MAC address for WAN interface of Archer A7/C7 v5Adrian Schmutzler2019-04-081-0/+5
| | | | | | | | | | | These devices share the network config with C7v4, thus the WAN MAC also needs to be fixed the same way. However, the partition where the MAC address resides has been changed. Based on: https://github.com/openwrt/openwrt/pull/1726 Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Fix GPIO reset button on TP-Link Archer C7v5Adrian Schmutzler2019-04-083-7/+18
| | | | | | | | | | | | | The GPIO for the reset button for the Archer C7v5 changed from ar71xx to ath79. An investigation based on tests revealed that the A7v5 responds on "11", while the C7v5 responds on "5" as set for ar71xx. Thus, we just define this in the DTS files instead of in the common DTSI. Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Utilize new LED modes from diag.sh for Archer A7/C7 v5Adrian Schmutzler2019-04-081-1/+4
| | | | | Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Consolidate LEDs in Archer A7/C7 v5 DTSIAdrian Schmutzler2019-04-081-48/+46
| | | | | | | | Definition is split here without obvious reason. Just merge it (and align order to that from C7 v4). Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for Ubiquiti airCube ISPChristian Mauderer2019-04-084-0/+115
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Ubiquiti Network airCube ISP is a cube shaped 2.4 GHz with internal 2x2 MIMO antennas. It can be supplied via a USB connector or via PoE. There are for 10/100 Mbps ports (1 * WAN + 3 * LAN). There is an optional PoE passthrough from the first LAN port to the WAN port. SoC: Qualcomm / Atheros QCA9533-BL3A RAM: 64 MB DDR2 Flash: 16 MB SPI NOR Ethernet: 4x 10/100 Mbps (1 WAN + 3 LAN) LEDS: 1x via a SPI controller (not yet supported) Buttons: 1x Reset Serial: 1x (only RX and TX); 115200 baud, 8N1 Missing points: - LED not yet supported - Factory upgrade via web IF or TFTP recovery not yet supported (Needs RSA signed images, for details see PR#1958) The serial port is on a four pin connextor labeled J1 and located between Ethernet and USB connector. The pinout is: 1. 3V3 (out) 2. Rx (in) 3. Tx (out) 4. GND Upgrading via serial port / U-Boot: - Connect the serial port via a level converter - Power the system and stop U-Boot with pressing any key when `Hit any key to stop autoboot` is displayed. Note: Pressing space multiple times untill U-Boot reaches that location works well. - Connect a PC with the IP 192.168.1.100 (or some other in that net) running a TFTP-Server to one of the LAN ports. Copy the sysupgrade image to the server. - Set the U-Boot server IP with setenv serverip 192.168.1.100 - Load the flash image to RAM with tftpboot 0x81000000 sysupgrade.bin - Erase the flash with erase 0x9f050000 0x9ffaffff - Write the new flash content with cp 0x81000000 0x9f050000 ${filesize} - Reset the device with reset Signed-off-by: Christian Mauderer <oss@c-mauderer.de> [removed full stop in subject and added lockdown note to commit message] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add support for OCEDO UrsusMarkus Scheck2019-04-084-2/+160
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SOC: Qualcomm Atheros QCA9558 RAM: 128MB FLASH: 16MB (Macronix MX25L12845EMI-10G) WLAN1: QCA9558 2.4GHz 802.11bgn 3SS WLAN2: QCA9880 5GHz 802.11ac 3SS LED: Power, LAN1, LAN2, 2.4GHz, 5GHz Serial:Next to SPI Flash, Pinout is 3V3 - GND - TX - RX (Square Pin is 3V3) The Serial setting is 115200-8-N-1 INSTALLATION: 1. Serve an OpenWrt ramdisk image named "ursus.bin". Set your IP-address to 192.168.100.8/24. 2. Connect to the serial. Power up the device and interrupt the boot process. 3. Set the correct bootcmd with > setenv bootcmd run bootcmd_1 > saveenv 4. Run > tftpboot 0x81000000 ursus.bin > bootm 0x81000000 5. Wait for OpenWrt to boot up. 6. Transfer OpenWrt sysupdate image and flash via sysupgrade. Signed-off-by: Markus Scheck <markus.scheck1@gmail.com> Tested-by: David Bauer <mail@david-bauer.net> [whitespace fix, renamed LED labels and SoC type fix] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: ag71xx: Enable tx hang workaround for the rest of ar724x SoCsPetr Štetiar2019-04-081-1/+8
| | | | | | | | | | | In ar71xx we check for stuck DMA on devices which fall in the is_ar724x SoC group (ar724x, ar933x, ar934x, qca9533, tp9343, qca955x, qca956x). In ath79 we're currently performing this check only for devices with ar7240 SoC, so this patch tries to sync the dma stuck checking behavior with what is being done in ar71xx. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ar71xx: ag71xx: Fix broken networking on some devices (FS#2177)Petr Štetiar2019-04-081-2/+3
| | | | | | | | | It was reported, that latest ar71xx builds have broken networking on TP-Link TL-WPA8630 and Nanostation M5 XW devices and that by reverting the offending commit, everything is back to normal. Fixes: d3506d1 ("ar71xx: ag71xx: fix compile error when enabling debug") Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ar71xx: Add support for Ubiquity Bullet M (XW)Petr Štetiar2019-04-088-0/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | CPU: AR9342 SoC RAM: 64 MB DDR2 Flash: 8 MB NOR SPI Ports: 100 MBit (24V PoE in) WLAN: 2.4/5 GHz UART: 1 UART on PCB marked as J1 with 115200 8N1 config LEDs: Power, Ethernet, 4x RSSI LEDs (orange, red, 2x green) Buttons: Reset UART connection details .---------------------------------. | | [ETH] J1 [ANT] | o VCC o RX o TX o GND | `---------------------------------' Flashing instructions using recovery method over TFTP 1. Unplug the ethernet cable from the router. 2. Using paper clip press and hold the router's reset button. Make sure you can feel it depressed by the paper clip. Do not release the button until step 4. 3. While keeping the reset button pressed in, plug the ethernet cable back into the AP. Keep the reset button depressed until you see the device's LEDs flashing in upgrade mode (alternating LED1/LED3 and LED2/LED4), this may take up to 25 seconds. 4. You may release the reset button, now the device should be in TFTP transfer mode. 5. Set a static IP on your Computer's NIC. A static IP of 192.168.1.25/24 should work. 6. Plug the PoE injector's LAN cable directly to your computer. 7. Start tftp client and issue following commands: tftp> binary tftp> connect 192.168.1.20 tftp> put openwrt-ar71xx-generic-ubnt-bullet-m-xw-squashfs-factory.bin Tested only on Bullet M2HP. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ar71xx: ubnt-m-xw: Fix factory image flashing using TFTP recoveryPetr Štetiar2019-04-081-2/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This is backport of the same functionality in ath79, from commit d42a7c469 ("ath79: ubnt-m-xw: Fix factory image flashing using TFTP recovery method") Ubiquity allows flashing of unsigned factory images via TFTP recovery method[1]. They claim in airOS v6.0.7 release changelog[2] following: All future airOS versions will be signed in this way and not allow unsigned firmware to be loaded except via TFTP. U-boot bootloader on M-XW devices expects factory image revision version in specific format. On airOS v6.1.7 with `U-Boot 1.1.4-s1039 (May 24 2017 - 15:58:18)` bootloader checks if the revision major(?) number is actually a number, but in currently generated images there's OpenWrt text and so the check fails: Hit any key to stop autoboot: 0 Setting default IP 192.168.1.20 Starting TFTP server... Receiving file from 192.168.1.25:38438 Received 4981148 bytes Firmware check failed! (1) By placing arbitrary correct number first in major version, we make the bootloader happy and we can flash factory images over TFTP again: Received 3801500 bytes Firmware Version: XW.ar934x.v6.0.4-42.OpenWrt-r9766+2-be42e44 Setting U-Boot environment variables Un-Protected 1 sectors Erasing Flash.... done Patch provided by AREDN[3] project, tested on Bullet M2 XW. 1. https://help.ubnt.com/hc/en-us/articles/204910124-UniFi-TFTP-Recovery-for-Bricked-Access-Points 2. https://dl.ubnt.com/firmwares/XW-fw/v6.0.7/changelog.txt 3. https://github.com/aredn Signed-off-by: Petr Štetiar <ynezz@true.cz>
* imx6: Add support for Toradex Apalis family of CoMsPetr Štetiar2019-04-0811-1/+495
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the following computer on modules (CoM) from Toradex[A]: Apalis iMX6 Quad 2GB IT - i.MX 6Quad 800MHz, 2GB DDR3, 4GB eMMC -40° to +85° C Temp Apalis iMX6 Quad 1GB - i.MX 6Quad 1GHz, 1GB DDR3, 4GB eMMC 0° to +70° C Temp Apalis iMX6 Dual 1GB IT - i.MX 6Dual 800MHz, 1GB DDR3, 4GB eMMC -40° to +85° C Temp Apalis iMX6 Dual 512MB - i.MX 6Dual 1GHz, 512MB DDR3, 4GB eMMC 0° to +70° C Temp I've developed and tested it on Quad 2GB IT v1.1A and Dual 512MB v1.1A CoMs, using Ixora[B] carrier board v1.0A, but it should hopefuly work on Eval[C] board as well. A. https://www.toradex.com/computer-on-modules/apalis-arm-family/nxp-freescale-imx-6 B. https://www.toradex.com/products/carrier-board/ixora-carrier-board C. https://www.toradex.com/products/carrier-board/apalis-evaluation-board Flashing/recovery instructions: 1. Download and compile imx_loader for OpenWrt from https://github.com/ynezz/imx_loader 2. Enter recovery mode as desribed in https://developer.toradex.com/knowledge-base/imx-recovery-mode 3. Connect board via USB to the host computer, check that it's connected by lsusb: 15a2:0054 Freescale Semiconductor, Inc. i.MX 6Dual/6Quad SystemOnChip in RecoveryMode 4. Copy following OpenWrt images to imx_loader directory: SPL u-boot.img u-boot-with-spl.imx openwrt-imx6-apalis-recovery.scr openwrt-imx6-apalis-squashfs.combined.bin 5. Run imx_usb in imx_loader directory Signed-off-by: Petr Štetiar <ynezz@true.cz>
* imx6: image: Split imx6-sdcard image for reusabilityPetr Štetiar2019-04-081-3/+16
| | | | | | | I'm going to reuse the imx6-sdcard image commands for building of Apalis eMMC images. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kernel: bump 4.19 to 4.19.34Koen Vandeputte2019-04-0838-211/+100
| | | | | | | | | | | | | | | | | | | | | | | | Refreshed all patches. Removed: - 030-PCI-dwc-skip-MSI-init-if-MSIs-have-been-explicitly-d.patch Altered: - 366-netfilter-nf_flow_table-clean-up-and-fix-dst-handlin.patch - 650-netfilter-add-xt_OFFLOAD-target.patch - 662-remove_pfifo_fast.patch - 332-arc-add-OWRTDTB-section.patch - 100-clocksource-drivers-arch_timer-Workaround-for-Allwin.patch - 702-phy_add_aneg_done_function.patch New symbols: - ARC_IRQ_NO_AUTOSAVE - SUN50I_ERRATUM_UNKNOWN1 Compile-tested: cns3xxx, imx6, sunxi Runtime-tested: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.111Koen Vandeputte2019-04-0810-18/+18
| | | | | | | | | Refreshed all patches. Compile-tested on: ar71xx, cns3xxx, imx6, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-07 01:21:54 +0000