From b9971db7c365c0145faf1db2e78ee48cee4b643d Mon Sep 17 00:00:00 2001 From: Damien Mascord Date: Mon, 7 Dec 2020 13:01:38 +1100 Subject: ath79: add support for Belkin F9J1108v2 (AC1750 DB Wi-Fi) This device is the non-US build of the F9K1115 v2, with a different firmware magic. Specifications: SoC: QCA9558 CPU: 720 MHz Flash: 16 MiB NOR RAM: 128 MiB WiFi 2.4 GHz: QCA9558-AT4A 3x3 MIMO 802.11b/g/n WiFi 5 GHz: QCA9880-2R4E 3x3 MIMO 802.11a/n/ac Ethernet: 4x LAN and 1x WAN (all 1gbps) USB: 1 x USB 2.0 (lower), 1 x USB 3.0 (upper) MAC addresses based on OEM firmware: Interface Address Location --------- ------- -------- lan *:5A sometimes in 0x6 wan *:5B 0x0 2.4Ghz *:5A 0x1002 5Ghz As per mini PCIe EEPROM Flashing instructions: The factory.bin can be flashed via the Belkin web UI or via the uboot http upgrade page. Once the factory.bin has been written, sysupgrade.bin will work as usual. Signed-off-by: Damien Mascord Acked-by: Martin Blumenstingl [wrap commit message/code, adjust label-mac-device, whitespace fixes, merge block in 02_network] Signed-off-by: Adrian Schmutzler --- .../linux/ath79/dts/qca9558_belkin_f9j1108-v2.dts | 229 +++++++++++++++++++++ .../generic/base-files/etc/board.d/02_network | 17 +- target/linux/ath79/image/generic.mk | 39 ++++ 3 files changed, 277 insertions(+), 8 deletions(-) create mode 100644 target/linux/ath79/dts/qca9558_belkin_f9j1108-v2.dts diff --git a/target/linux/ath79/dts/qca9558_belkin_f9j1108-v2.dts b/target/linux/ath79/dts/qca9558_belkin_f9j1108-v2.dts new file mode 100644 index 0000000000..0bd3af98db --- /dev/null +++ b/target/linux/ath79/dts/qca9558_belkin_f9j1108-v2.dts @@ -0,0 +1,229 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qca955x.dtsi" + +#include +#include + +/ { + model = "Belkin F9J1108 v2 (AC1750 DB Wi-Fi)"; + compatible = "belkin,f9j1108-v2", "qca,qca9558"; + + aliases { + led-boot = &led_system; + led-failsafe = &led_system; + led-running = &led_system; + led-upgrade = &led_system; + label-mac-device = ð1; + }; + + leds { + compatible = "gpio-leds"; + + usb { + label = "green:usb2"; + gpios = <&gpio 4 GPIO_ACTIVE_LOW>; + trigger-sources = <&hub_port0>; + linux,default-trigger = "usbport"; + }; + + status { + label = "amber:status"; + gpios = <&gpio 15 GPIO_ACTIVE_LOW>; + }; + + wps-amber { + label = "amber:wps"; + gpios = <&gpio 14 GPIO_ACTIVE_LOW>; + }; + + wps-blue { + label = "blue:wps"; + gpios = <&gpio 19 GPIO_ACTIVE_LOW>; + }; + + led_system: system { + label = "blue:system"; + gpios = <&gpio 20 GPIO_ACTIVE_LOW>; + }; + }; + + gpio-export { + compatible = "gpio-export"; + #size-cells = <0>; + + usb2_power { + gpio-export,name = "usb2:power"; + gpio-export,output = <1>; + gpios = <&gpio 21 GPIO_ACTIVE_HIGH>; + }; + }; + + keys { + compatible = "gpio-keys"; + + wps { + label = "WPS button"; + linux,code = ; + gpios = <&gpio 16 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + + reset { + label = "Reset button"; + linux,code = ; + gpios = <&gpio 17 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + }; + + virtual_flash { + compatible = "mtd-concat"; + + devices = <&fwpart1 &fwpart2>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + compatible = "openwrt,okli"; + label = "firmware"; + reg = <0x0 0x0>; + }; + }; + }; +}; + +&pcie1 { + status = "okay"; +}; + +&uart { + status = "okay"; +}; + +&usb_phy0 { + status = "okay"; +}; + +&usb0 { + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + hub_port0: port@1 { + reg = <1>; + #trigger-source-cells = <0>; + }; +}; + +&spi { + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <80000000>; + m25p,fast-read; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + uboot: partition@0 { + label = "u-boot"; + reg = <0x000000 0x040000>; + read-only; + }; + + partition@40000 { + label = "u-boot-env"; + reg = <0x040000 0x010000>; + }; + + fwpart1: partition@50000 { + label = "fwpart1"; + reg = <0x050000 0xe20000>; + }; + + partition@e70000 { + label = "loader"; + reg = <0xe70000 0x10000>; + read-only; + }; + + fwpart2: partition@e80000 { + label = "fwpart2"; + reg = <0xe80000 0x170000>; + }; + + art: partition@ff0000 { + label = "art"; + reg = <0xff0000 0x010000>; + }; + }; + }; +}; + +&mdio0 { + status = "okay"; + + phy0: ethernet-phy@0 { + reg = <0>; + + qca,ar8327-initvals = < + 0x04 0x00080080 /* PORT0 PAD MODE CTRL */ + 0x0c 0x07600000 /* PORT6 PAD MODE CTRL */ + 0x50 0xc737c737 /* LED_CTRL0 */ + 0x54 0x00000000 /* LED_CTRL1 */ + 0x58 0x00000000 /* LED_CTRL2 */ + 0x5c 0x0030c300 /* LED_CTRL3 */ + 0x7c 0x0000007e /* PORT0_STATUS */ + 0x94 0x0000007e /* PORT6 STATUS */ + >; + }; +}; + +ð0 { + status = "okay"; + + mtd-mac-address = <&art 0x0>; + phy-handle = <&phy0>; + pll-data = <0xa6000000 0x00000101 0x00001616>; + + gmac-config { + device = <&gmac>; + rgmii-enabled = <1>; + }; +}; + +ð1 { + status = "okay"; + + mtd-mac-address = <&art 0x0>; + mtd-mac-address-increment = <(-1)>; + pll-data = <0x03000101 0x00000101 0x00001616>; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&pcie0 { + status = "okay"; + + wifi@0,0 { + compatible = "qcom,ath10k"; + reg = <0 0 0 0 0>; + }; +}; + +&wmac { + status = "okay"; + + mtd-cal-data = <&art 0x1000>; +}; diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network index 149f7b1141..987b405431 100755 --- a/target/linux/ath79/generic/base-files/etc/board.d/02_network +++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network @@ -100,6 +100,15 @@ ath79_setup_interfaces() ucidef_add_switch "switch0" \ "0@eth0" "1:lan:1" "2:lan:4" "3:lan:3" "4:lan:2" ;; + belkin,f9j1108-v2|\ + tplink,archer-c5-v1|\ + tplink,archer-c7-v1|\ + tplink,archer-c7-v2|\ + tplink,tl-wdr4900-v2|\ + tplink,tl-wdr7500-v3) + ucidef_add_switch "switch0" \ + "0@eth1" "2:lan" "3:lan" "4:lan" "5:lan" "6@eth0" "1:wan" + ;; buffalo,bhr-4grv|\ buffalo,wzr-hp-g450h) ucidef_add_switch "switch0" \ @@ -308,14 +317,6 @@ ath79_setup_interfaces() ucidef_add_switch "switch0" \ "0@eth0" "2:lan:3" "3:lan:2" "4:lan:1" ;; - tplink,archer-c5-v1|\ - tplink,archer-c7-v1|\ - tplink,archer-c7-v2|\ - tplink,tl-wdr4900-v2|\ - tplink,tl-wdr7500-v3) - ucidef_add_switch "switch0" \ - "0@eth1" "2:lan" "3:lan" "4:lan" "5:lan" "6@eth0" "1:wan" - ;; tplink,archer-d50-v1) ucidef_add_switch "switch0" \ "0@eth0" "2:lan:3" "3:lan:2" "4:lan:1" "1:wan" diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk index 614f9ff0b2..d5fbd89c26 100644 --- a/target/linux/ath79/image/generic.mk +++ b/target/linux/ath79/image/generic.mk @@ -50,6 +50,24 @@ define Build/cybertan-trx -rm $@-empty.bin endef +define Build/edimax-headers + $(eval edimax_magic=$(word 1,$(1))) + $(eval edimax_model=$(word 2,$(1))) + + $(STAGING_DIR_HOST)/bin/edimax_fw_header -M $(edimax_magic) -m $(edimax_model)\ + -v $(VERSION_DIST)$(firstword $(subst +, , $(firstword $(subst -, ,$(REVISION))))) \ + -n "uImage" \ + -i $(KDIR)/loader-$(DEVICE_NAME).uImage \ + -o $@.uImage + $(STAGING_DIR_HOST)/bin/edimax_fw_header -M $(edimax_magic) -m $(edimax_model)\ + -v $(VERSION_DIST)$(firstword $(subst +, , $(firstword $(subst -, ,$(REVISION))))) \ + -n "rootfs" \ + -i $@ \ + -o $@.rootfs + cat $@.uImage $@.rootfs > $@ + rm -rf $@.uImage $@.rootfs +endef + # This needs to make /tmp/_sys/sysupgrade.tgz an empty file prior to # sysupgrade, as otherwise it will implant the old configuration from # OEM firmware when writing rootfs from factory.bin @@ -363,6 +381,27 @@ define Device/avm_fritzdvbc endef TARGET_DEVICES += avm_fritzdvbc +define Device/belkin_f9j1108-v2 + SOC := qca9558 + DEVICE_VENDOR := Belkin + DEVICE_MODEL := F9J1108 v2 (AC1750 DB Wi-Fi) + IMAGE_SIZE := 14464k + DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct kmod-usb2 \ + kmod-usb3 kmod-usb-ledtrig-usbport + LOADER_TYPE := bin + LOADER_FLASH_OFFS := 0x50000 + COMPILE := loader-$(1).bin loader-$(1).uImage + COMPILE/loader-$(1).bin := loader-okli-compile + COMPILE/loader-$(1).uImage := append-loader-okli $(1) | pad-to 64k | \ + lzma | uImage lzma + KERNEL := kernel-bin | append-dtb | lzma | uImage lzma -M 0x4f4b4c49 + IMAGES += factory.bin + IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \ + append-rootfs | pad-rootfs | check-size | \ + edimax-headers F9J1108v1 BR-6679BAC | pad-to $$$$(BLOCKSIZE) +endef +TARGET_DEVICES += belkin_f9j1108-v2 + define Device/buffalo_bhr-4grv $(Device/buffalo_common) SOC := ar7242 -- cgit v1.2.3