From b9389186b012e5bd99ea6523b8220aaee6ca0085 Mon Sep 17 00:00:00 2001
From: Dongming Han <handongming@gl-inet.com>
Date: Wed, 22 Jul 2020 15:12:17 +0800
Subject: ipq40xx: add support for GL.iNet GL-AP1300
Specifications:
SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM: 256 MiB
FLASH1: 4 MiB NOR
FLASH2: 128 MiB NAND
ETH: Qualcomm QCA8075
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2
INPUT: Reset
LED: Power, Internet
UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1
OTHER: On board with BLE module - by cp210x USB serial chip
On board hareware watchdog with GPIO0 high to turn on, and GPIO4 for watchdog feed
Install via uboot tftp or uboot web failsafe.
By uboot tftp:
(IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-generic-glinet_gl-ap1300-squashfs-nand-factory.ubi
(IPQ40xx) # run lf
By uboot web failsafe:
Push the reset button for 10 seconds util the power led flash faster,
then use broswer to access http://192.168.1.1
Afterwards upgrade can use sysupgrade image.
Signed-off-by: Dongming Han <handongming@gl-inet.com>
---
package/firmware/ipq-wifi/Makefile | 2 ++
.../firmware/ipq-wifi/board-glinet_gl-ap1300.qca4019 | Bin 0 -> 48596 bytes
2 files changed, 2 insertions(+)
create mode 100644 package/firmware/ipq-wifi/board-glinet_gl-ap1300.qca4019
(limited to 'package/firmware')
diff --git a/package/firmware/ipq-wifi/Makefile b/package/firmware/ipq-wifi/Makefile
index f42704b8d3..e5f10a1f98 100644
--- a/package/firmware/ipq-wifi/Makefile
+++ b/package/firmware/ipq-wifi/Makefile
@@ -38,6 +38,7 @@ ALLWIFIBOARDS:= \
engenius_emd1 \
engenius_emr3500 \
ezviz_cs-w3-wd1200g-eup \
+ glinet_gl-ap1300 \
glinet_gl-s1300 \
linksys_ea8300 \
linksys_mr8300-v0 \
@@ -120,6 +121,7 @@ $(eval $(call generate-ipq-wifi-package,engenius_eap2200,EnGenius EAP2200))
$(eval $(call generate-ipq-wifi-package,engenius_emd1,EnGenius EMD1))
$(eval $(call generate-ipq-wifi-package,engenius_emr3500,EnGenius EMR3500))
$(eval $(call generate-ipq-wifi-package,ezviz_cs-w3-wd1200g-eup,EZVIZ CS-W3-WD1200G EUP))
+$(eval $(call generate-ipq-wifi-package,glinet_gl-ap1300,GL.iNet GL-AP1300))
$(eval $(call generate-ipq-wifi-package,glinet_gl-s1300,GL.iNet GL-S1300))
$(eval $(call generate-ipq-wifi-package,linksys_ea8300,Linksys EA8300))
$(eval $(call generate-ipq-wifi-package,linksys_mr8300-v0,Linksys MR8300))
diff --git a/package/firmware/ipq-wifi/board-glinet_gl-ap1300.qca4019 b/package/firmware/ipq-wifi/board-glinet_gl-ap1300.qca4019
new file mode 100644
index 0000000000..481dd81b5b
Binary files /dev/null and b/package/firmware/ipq-wifi/board-glinet_gl-ap1300.qca4019 differ
--
cgit v1.2.3