From 01dda0659eb7d029672af3bd3b590d98e2ee0a5d Mon Sep 17 00:00:00 2001 From: Piotr Dymacz Date: Thu, 6 Oct 2016 02:19:17 +0200 Subject: ar71xx: add support for YunCore AP90Q YunCore AP90Q is an outdoor CPE/AP based on Qualcomm/Atheros QCA9531 v2. Short specification: - 650/600/216 MHz (CPU/DDR/AHB) - 2x 10/100 Mbps Ethernet, passive PoE support - 64/128 MB of RAM (DDR2) - 16 MB of FLASH - 2T2R 2.4 GHz with external PA, up to 29 dBm - 2x internal 5 dBi omni antennas - 4x LED, 1x button - UART (JP1) header on PCB Flash instruction under U-Boot, using UART: 1. tftp 0x80060000 lede-ar71xx-generic-ap90q-squashfs-sysupgrade 2. erase 0x9f050000 +$filesize 3. cp.b $fileaddr 0x9f050000 $filesize 4. setenv bootcmd "bootm 0x9f050000" 5. saveenv && reset Flash instruction under vendor fimrware, using telnet/SSH: 1. Connect PC with 192.168.1.x address to WAN port 2. Power up device, enter failsafe mode with button (no LED indicator!) 3. Change root password and reboot (mount_root, passwd ..., reboot -f) 4. Upload lede-ar71xx-generic-ap90q-squashfs-sysupgrade.bin to /tmp using SCP 5. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253 6. Invoke: - cd /tmp - fw_setenv bootcmd "bootm 0x9f050000" - mtd erase firmware - mtd -r write lede-ar71xx-generic-ap90q-squashfs-sysupgrade.bin firmware Signed-off-by: Piotr Dymacz --- target/linux/ar71xx/base-files/etc/board.d/01_leds | 15 +++++++++++---- 1 file changed, 11 insertions(+), 4 deletions(-) (limited to 'target/linux/ar71xx/base-files/etc/board.d') diff --git a/target/linux/ar71xx/base-files/etc/board.d/01_leds b/target/linux/ar71xx/base-files/etc/board.d/01_leds index 29ee5d7b12..c348b4fbda 100755 --- a/target/linux/ar71xx/base-files/etc/board.d/01_leds +++ b/target/linux/ar71xx/base-files/etc/board.d/01_leds @@ -57,6 +57,17 @@ ap147-010) ucidef_set_led_switch "lan4" "LAN4" "ap147:green:lan4" "switch0" "0x02" ucidef_set_led_wlan "wlan2g" "WLAN 2.4 GHz" "ap147:green:wlan-2g" "phy0tpt" ;; +ap90q|\ +dr531) + ucidef_set_led_netdev "lan" "LAN" "$board:green:lan" "eth0" + ucidef_set_led_netdev "wan" "WAN" "$board:green:wan" "eth1" + + case "$board" in + ap90q) + ucidef_set_led_wlan "wlan" "WLAN" "$board:green:wlan" "phy0tpt" + ;; + esac + ;; bhr-4grv2) ucidef_set_led_default "power" "POWER" "buffalo:green:power" "1" ucidef_set_led_default "diag" "DIAG" "buffalo:red:diag" "0" @@ -152,10 +163,6 @@ cr5000) ucidef_set_led_wlan "wlan" "WLAN" "pcs:blue:wlan" "phy0tpt" ucidef_set_led_usbdev "usb" "USB" "pcs:white:wps" "1-1" ;; -dr531) - ucidef_set_led_netdev "lan" "LAN" "$board:green:lan" "eth0" - ucidef_set_led_netdev "wan" "WAN" "$board:green:wan" "eth1" - ;; dragino2) ucidef_set_led_wlan "wlan" "WLAN" "$board:red:wlan" "phy0tpt" ucidef_set_led_netdev "lan" "LAN" "$board:red:lan" "eth0" -- cgit v1.2.3