From db91418766562fde7da468a19c87f25bc8aad8a0 Mon Sep 17 00:00:00 2001 From: Piotr Dymacz Date: Mon, 11 Mar 2019 18:50:42 +0100 Subject: ath79: add support for TP-Link RE350K v1 TP-Link RE350K v1 (FCC ID: TE7RE350K) is a wall-plug AC1200 Wi-Fi range extender with 'Kasa Smart' support. Device is based on Qualcomm/Atheros QCA9558 + QCA9882 + AR8035 platform and is available only on US market. Specification: - 720/600/200 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of flash (SPI NOR) - 1x 1 Gbps Ethernet (AR8035) - 2T2R 2.4 GHz (QCA9558), with ext. PA (SE2565T) and LNA (SKY65971-11) - 2T2R 5 GHz (QCA9882), with ext. PA (SE5003L1-R) and LNA (SKY65981-11) - 2x U.FL connector on PCB - 2x dual-band PCB antennas - 1x LED, 2x dual-color LED (all driven by GPIO) - 3x button (app config, led, reset) - 1x mechanical on/off slide switch - 1x UART (4-pin, 2.54 mm pitch) header on PCB - 1x JTAG (8-pin, 1.27 mm pitch) header on PCB Flash instruction: Use 'factory' image directly in vendor GUI (default IP: 192.168.0.254, default credentials: admin/admin). Warning: This device does not include any kind of recovery mechanism in U-Boot. Vendor firmware access: You can access vendor firmware over serial (RX line requires jumper resistor in R306 place, near XTAL) with: root/sohoadmin credentials. Signed-off-by: Piotr Dymacz --- .../linux/ath79/dts/qca9558_tplink_re350k-v1.dts | 173 +++++++++++++++++++++ 1 file changed, 173 insertions(+) create mode 100644 target/linux/ath79/dts/qca9558_tplink_re350k-v1.dts (limited to 'target/linux/ath79/dts/qca9558_tplink_re350k-v1.dts') diff --git a/target/linux/ath79/dts/qca9558_tplink_re350k-v1.dts b/target/linux/ath79/dts/qca9558_tplink_re350k-v1.dts new file mode 100644 index 0000000000..056b513d7e --- /dev/null +++ b/target/linux/ath79/dts/qca9558_tplink_re350k-v1.dts @@ -0,0 +1,173 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include +#include + +#include "qca9557.dtsi" + +/ { + model = "TP-Link RE350K v1"; + compatible = "tplink,re350k-v1", "qca,qca9558"; + + aliases { + led-boot = &power; + led-failsafe = &power; + led-running = &power; + led-upgrade = &power; + mdio-gpio0 = &mdio2; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + keys { + compatible = "gpio-keys"; + + app-config { + label = "app-config"; + linux,code = ; + gpios = <&gpio 20 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + + led { + label = "led"; + linux,code = ; + gpios = <&gpio 19 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + + reset { + label = "reset"; + linux,code = ; + gpios = <&gpio 17 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + }; + + leds { + compatible = "gpio-leds"; + + power: power { + label = "tp-link:green:power"; + gpios = <&gpio 12 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + + wlan2g-green { + label = "tp-link:green:wlan2g"; + gpios = <&gpio 16 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy1tpt"; + }; + + wlan2g-red { + label = "tp-link:red:wlan2g"; + gpios = <&gpio 21 GPIO_ACTIVE_LOW>; + }; + + wlan5g-green { + label = "tp-link:green:wlan5g"; + gpios = <&gpio 14 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + }; + + wlan5g-red { + label = "tp-link:red:wlan5g"; + gpios = <&gpio 22 GPIO_ACTIVE_LOW>; + }; + }; + + mdio2: mdio { + compatible = "virtual,mdio-gpio"; + + #address-cells = <1>; + #size-cells = <0>; + + gpios = <&gpio 23 GPIO_ACTIVE_HIGH>, + <&gpio 18 GPIO_ACTIVE_HIGH>; + + phy0: ethernet-phy@4 { + reg = <4>; + + phy-mode = "rgmii-rxid"; + at803x-disable-smarteee; + }; + }; +}; + +ð0 { + status = "okay"; + + mtd-mac-address = <&config 0x10008>; + pll-data = <0x9e000000 0x80000101 0x80001313>; + phy-handle = <&phy0>; + + gmac-config { + device = <&gmac>; + + rxdv-delay = <2>; + rxd-delay = <2>; + txen-delay = <0>; + txd-delay = <0>; + rgmii-enabled = <1>; + }; +}; + +&pcie0 { + status = "okay"; +}; + +&spi { + status = "okay"; + + num-cs = <1>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <25000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x000000 0x020000>; + read-only; + }; + + partition@20000 { + compatible = "tplink,firmware"; + label = "firmware"; + reg = <0x020000 0xd70000>; + }; + + config: partition@d90000 { + label = "config"; + reg = <0xd90000 0x260000>; + read-only; + }; + + art: partition@ff0000 { + label = "art"; + reg = <0xff0000 0x010000>; + read-only; + }; + }; + }; +}; + +&uart { + status = "okay"; +}; + +&wmac { + status = "okay"; + + mtd-cal-data = <&art 0x1000>; + mtd-mac-address = <&config 0x10008>; +}; -- cgit v1.2.3