From 15f585afc5b66f5addb6667001c303b5fd502ce5 Mon Sep 17 00:00:00 2001 From: "Leon M. George" Date: Fri, 26 Jul 2019 20:34:01 +0200 Subject: ath79: add support for Compex WPJ563 MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Specifications: SoC: QCA9563 DRAM: 128MB DDR2 Flash: 16MB SPI-NOR 2 Gigabit ethernet ports 3×3 2.4GHz on-board radio miniPCIe slot that supports 5GHz radio PoE 24V passive or 36V-56V passive with optional IEEE 802.3af/at USB 3.0 header Installation: To install, either start tftp in bin/targets/ath79/generic/ and use the u-boot prompt over UART: tftpboot 0x80500000 openwrt-ath79-generic-compex_wpj563-squashfs-sysupgrade.bin erase 0x9f680000 +1 erase 0x9f030000 +$filesize cp.b $fileaddr 0x9f030000 $filesize boot The cpximg file can be used with sysupgrade in the stock firmware (add SSH key in luci for root access) or with the built-in cpximg loader. The cpximg loader can be started either by holding the reset button during power up or by entering the u-boot prompt and entering 'cpximg'. Once it's running, a TFTP-server under 192.168.1.1 will accept the image appropriate for the board revision that is etched on the board. For example, if the board is labelled '7A02': tftp -v -m binary 192.168.1.1 -c put openwrt-ath79-generic-compex_wpj563-squashfs-cpximg-7a02.bin MAC addresses: <&uboot 0x2e010> *:71 (label) <&uboot 0x2e018> *:72 <&uboot 0x2e020> *:73 <&uboot 0x2e028> *:74 Only the first two are used (for ethernet), the WiFi modules have separate (valid) addresses. The latter two addresses are not used. Signed-off-by: Leon M. George --- target/linux/ath79/dts/qca9563_compex_wpj563.dts | 145 +++++++++++++++++++++++ 1 file changed, 145 insertions(+) create mode 100644 target/linux/ath79/dts/qca9563_compex_wpj563.dts (limited to 'target/linux/ath79/dts') diff --git a/target/linux/ath79/dts/qca9563_compex_wpj563.dts b/target/linux/ath79/dts/qca9563_compex_wpj563.dts new file mode 100644 index 0000000000..ae9dd5c460 --- /dev/null +++ b/target/linux/ath79/dts/qca9563_compex_wpj563.dts @@ -0,0 +1,145 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include +#include + +#include "qca956x.dtsi" + +/ { + model = "Compex WPJ563"; + compatible = "compex,wpj563", "qca,qca9563"; + + aliases { + label-mac-device = ð0; + led-boot = &led_sig4; + led-failsafe = &led_sig4; + led-running = &led_sig4; + led-upgrade = &led_sig4; + }; + + beeper { + compatible = "gpio-beeper"; + gpios = <&gpio 19 GPIO_ACTIVE_HIGH>; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + linux,code = ; + gpios = <&gpio 2 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + }; + + leds { + compatible = "gpio-leds"; + + sig1 { + label = "wpj563:green:sig1"; + gpios = <&gpio 1 GPIO_ACTIVE_LOW>; + }; + + sig2 { + label = "wpj563:green:sig2"; + gpios = <&gpio 5 GPIO_ACTIVE_LOW>; + }; + + sig3 { + label = "wpj563:green:sig4"; + gpios = <&gpio 6 GPIO_ACTIVE_LOW>; + }; + + led_sig4: sig4 { + label = "wpj563:green:sig4"; + gpios = <&gpio 7 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&pcie { + status = "okay"; +}; + +&spi { + status = "okay"; + + num-cs = <1>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <25000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + uboot: partition@0 { + label = "u-boot"; + reg = <0x000000 0x030000>; + read-only; + }; + + partition@30000 { + compatible = "denx,uimage"; + label = "firmware"; + reg = <0x030000 0xfc0000>; + }; + + art: partition@ff0000 { + label = "art"; + reg = <0xff0000 0x010000>; + read-only; + }; + }; + }; +}; + +&mdio0 { + status = "okay"; + + phy-mask = <0>; + + phy0: ethernet-phy@0 { + reg = <0>; + phy-mode = "sgmii"; + qca,mib-poll-interval = <500>; + + qca,ar8327-initvals = < + 0x04 0x00080080 /* PORT0 PAD MODE CTRL */ + 0x7c 0x0000007e /* PORT0_STATUS */ + >; + }; +}; + +ð0 { + status = "okay"; + + pll-data = <0x03000101 0x00000101 0x00001919>; + + mtd-mac-address = <&uboot 0x2e010>; + phy-mode = "sgmii"; + phy-handle = <&phy0>; +}; + +&usb_phy0 { + status = "okay"; +}; + +&usb0 { + status = "okay"; +}; + +&uart { + status = "okay"; +}; + +&wmac { + status = "okay"; + + mtd-cal-data = <&art 0x1000>; +}; -- cgit v1.2.3