From dd1d95cb0357278900d09fae3ad20e9e0b2d569a Mon Sep 17 00:00:00 2001 From: Sven Eckelmann Date: Mon, 23 Nov 2020 13:41:34 +0100 Subject: ath79: Add support for OpenMesh OM2P v4 Device specifications: ====================== * Qualcomm/Atheros QCA9533 v2 * 650/600/217 MHz (CPU/DDR/AHB) * 64 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 2x 10/100 Mbps Ethernet * 1T1R 2.4 GHz Wi-Fi * 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x fast ethernet - eth0 + Label: Ethernet 1 + 24V passive POE (mode B) - eth1 + Label: Ethernet 2 + 802.3af POE + builtin switch port 1 * 12-24V 1A DC * external antenna Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 .bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp .bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/.bin Signed-off-by: Sven Eckelmann [wrap two very long lines, fix typo in comment] Signed-off-by: Adrian Schmutzler --- .../linux/ath79/dts/qca9533_openmesh_om2p-v4.dts | 8 ++ .../linux/ath79/dts/qca9533_openmesh_om2p-v4.dtsi | 157 +++++++++++++++++++++ 2 files changed, 165 insertions(+) create mode 100644 target/linux/ath79/dts/qca9533_openmesh_om2p-v4.dts create mode 100644 target/linux/ath79/dts/qca9533_openmesh_om2p-v4.dtsi (limited to 'target/linux/ath79/dts') diff --git a/target/linux/ath79/dts/qca9533_openmesh_om2p-v4.dts b/target/linux/ath79/dts/qca9533_openmesh_om2p-v4.dts new file mode 100644 index 0000000000..b738afad33 --- /dev/null +++ b/target/linux/ath79/dts/qca9533_openmesh_om2p-v4.dts @@ -0,0 +1,8 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qca9533_openmesh_om2p-v4.dtsi" + +/ { + compatible = "openmesh,om2p-v4", "qca,qca9533"; + model = "OpenMesh OM2P v4"; +}; diff --git a/target/linux/ath79/dts/qca9533_openmesh_om2p-v4.dtsi b/target/linux/ath79/dts/qca9533_openmesh_om2p-v4.dtsi new file mode 100644 index 0000000000..74daba3f93 --- /dev/null +++ b/target/linux/ath79/dts/qca9533_openmesh_om2p-v4.dtsi @@ -0,0 +1,157 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qca953x.dtsi" + +#include +#include + +/ { + chosen { + /delete-property/ bootargs; + }; + + aliases { + led-boot = &led_power_blue; + led-failsafe = &led_power_blue; + led-running = &led_power_blue; + led-upgrade = &led_power_blue; + label-mac-device = ð0; + }; + + keys { + compatible = "gpio-keys"; + + pinctrl-names = "default"; + pinctrl-0 = <&jtag_disable_pins>; + + reset { + label = "reset"; + linux,code = ; + gpios = <&gpio 1 GPIO_ACTIVE_LOW>; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_power_blue: power_blue { + label = "blue:power"; + gpios = <&gpio 0 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + + wifi_green { + label = "green:wifi"; + gpios = <&gpio 2 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + }; + + wifi_yellow { + label = "yellow:wifi"; + gpios = <&gpio 3 GPIO_ACTIVE_LOW>; + }; + + wifi_red { + label = "red:wifi"; + gpios = <&gpio 4 GPIO_ACTIVE_LOW>; + }; + + wan_blue { + label = "blue:wan"; + gpios = <&gpio 13 GPIO_ACTIVE_LOW>; + }; + + lan_blue { + label = "blue:lan"; + gpios = <&gpio 14 GPIO_ACTIVE_LOW>; + }; + }; + + watchdog { + compatible = "linux,wdt-gpio"; + gpios = <&gpio 12 GPIO_ACTIVE_LOW>; + hw_algo = "toggle"; + /* hw_margin_ms is actually 300s but driver limits it to 60s */ + hw_margin_ms = <60000>; + always-running; + }; +}; + +&uart { + status = "okay"; +}; + +&spi { + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <25000000>; + + /* partitions are passed via bootloader */ + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x000000 0x040000>; + read-only; + }; + + partition@40000 { + label = "u-boot-env"; + reg = <0x040000 0x040000>; + }; + + partition@80000 { + label = "custom"; + reg = <0x080000 0x140000>; + read-only; + }; + + partition@1c0000 { + label = "inactive"; + reg = <0x1c0000 0x700000>; + }; + + partition@8c0000 { + label = "inactive2"; + reg = <0x8c0000 0x700000>; + }; + + art: partition@fc0000 { + label = "ART"; + reg = <0xfc0000 0x040000>; + read-only; + }; + }; + }; +}; + +ð0 { + status = "okay"; + + phy-handle = <&swphy4>; + + mtd-mac-address = <&art 0x0>; +}; + +ð1 { + /* Workaround: keep the Ethernet interfaces order/mapping correct + * (GMAC0 -> eth0, GMAC1 -> eth1, same as in old ar71xx target) + */ + compatible = "qca,qca9530-eth", "syscon", "simple-mfd"; + + mtd-mac-address = <&art 0x6>; +}; + +&wmac { + status = "okay"; + + mtd-cal-data = <&art 0x1000>; + mtd-mac-address = <&art 0x0>; + mtd-mac-address-increment = <2>; +}; -- cgit v1.2.3