From a873b292840848b67addb5be0c762d292bde33a1 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Oever=20Gonz=C3=A1lez?= Date: Wed, 23 Jan 2019 21:20:55 -0600 Subject: ipq40xx: add support for Linksys EA6350v3 MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Specifications: SOC: Qualcomm IPQ4018 RAM: 256 MiB Samsung K4B2G1646F-BYK0 FLASH1: MX25L1605D 2 MB FLASH2: Winbond W25N01GV 128Mb ETH: Qualcomm QCA8075 WLAN0: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2 WLAN1: Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2 INPUT: WPS, Reset LED: Status - Green SERIAL: Header at J19, Beneath DC Power Jack 1-VCC ; 2-TX ; 3-RX; 4-GND; Serial 115200-8-N-1. Tested and working: - USB (requires extra packages) - LAN Ethernet (Correct MAC-address) - WAN Ethernet (Correct MAC-address) - 2.4 GHz WiFi (Correct MAC-address) - 5 GHz WiFi (Correct MAC-address) - Factory installation from Web UI - OpenWRT sysupgrade - LED - Reset Button Need Testing: - WPS button Install via Web UI: - Attach to a LAN port on the router. - Connect to the Linksys Smart WiFi Page (default 192.168.1.1) and login - Select the connectivity tab on the left - In the manual update box on the right - Select browse, and browse to openwrt-ipq40xx-linksys_ea6350v3-squashfs-factory.bin - Click update. - Read and accept the warning - The router LED will start blinking. When the router LED goes solid, you can now navigate to 192.168.1.1 to your new OpenWrt installation. Sysupgrade: - Flash the sysupgrade image as usual. Please: try to do a reset everytime you can (doing it with LuCI is easy and can be done in the same step). Recovery (Automatic): - If the device fails to boot after install or upgrade, whilst the unit is turned on: 1 - Wait 15 seconds 2 - Switch Off and Wait 10 seconds 3 - Switch on 4 - Repeat steps 1 to 3, 3 times then go to 5. 5 - U-boot will have now erased the failed update and switched back to the last working firmware - you should be able to access your router on LAN. Recovery (Manual): - The steps for manual recovery are the same as the generic u-boot tftp client method. Back To Stock: - Use the generic recovery using the tftp client method to flash the "civic.img". Also you can strip-and-pad the original image and use the generic "mtd" method by flashing over the "kernel" partition. * Just be careful to flash in the partition that the device is currently booted. Signed-off-by: Ryan Pannell Signed-off-by: Oever González [minor edits, removed second compatible of nand, added dtb entry to 4.19] Signed-off-by: Christian Lamparter --- .../arch/arm/boot/dts/qcom-ipq4018-ea6350v3.dts | 273 +++++++++++++++++++++ 1 file changed, 273 insertions(+) create mode 100644 target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4018-ea6350v3.dts (limited to 'target/linux/ipq40xx/files-4.19/arch') diff --git a/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4018-ea6350v3.dts b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4018-ea6350v3.dts new file mode 100644 index 0000000000..a6f1e1c5b2 --- /dev/null +++ b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4018-ea6350v3.dts @@ -0,0 +1,273 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qcom-ipq4019.dtsi" +#include +#include +#include + +/ { + model = "Linksys EA6350v3"; + compatible = "linksys,ea6350v3"; + + aliases { + led-boot = &power; + led-failsafe = &power; + led-running = &power; + led-upgrade = &power; + }; + + soc { + mdio@90000 { + status = "okay"; + }; + + ess-psgmii@98000 { + status = "okay"; + }; + + tcsr@1949000 { + compatible = "qcom,tcsr"; + reg = <0x1949000 0x100>; + qcom,wifi_glb_cfg = ; + }; + + tcsr@194b000 { + compatible = "qcom,tcsr"; + reg = <0x194b000 0x100>; + qcom,usb-hsphy-mode-select = ; + }; + + ess_tcsr@1953000 { + compatible = "qcom,tcsr"; + reg = <0x1953000 0x1000>; + qcom,ess-interface-select = ; + }; + + tcsr@1957000 { + compatible = "qcom,tcsr"; + reg = <0x1957000 0x100>; + qcom,wifi_noc_memtype_m0_m2 = ; + }; + + usb2@60f8800 { + status = "okay"; + }; + + usb3@8af8800 { + status = "okay"; + }; + + crypto@8e3a000 { + status = "okay"; + }; + + watchdog@b017000 { + status = "okay"; + }; + + ess-switch@c000000 { + status = "okay"; + }; + + edma@c080000 { + status = "okay"; + }; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&tlmm 63 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + wps { + label = "wps"; + gpios = <&tlmm 0 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + + power: status { + label = "EA6350v3:green:status"; + gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&blsp1_uart1 { + pinctrl-0 = <&serial_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&cryptobam { + status = "okay"; +}; + +&wifi0 { + status = "okay"; + qcom,ath10k-calibration-variant = "linksys-ea6350v3"; +}; + +&wifi1 { + status = "okay"; + qcom,ath10k-calibration-variant = "linksys-ea6350v3"; +}; + + +&blsp_dma { + status = "okay"; +}; + +&tlmm { + serial_pins: serial_pinmux { + mux { + pins = "gpio60", "gpio61"; + function = "blsp_uart0"; + bias-disable; + }; + }; + + spi_0_pins: spi_0_pinmux { + mux { + function = "blsp_spi0"; + pins = "gpio55", "gpio56", "gpio57"; + drive-strength = <12>; + bias-disable; + }; + + mux_cs { + function = "gpio"; + pins = "gpio54", "gpio59"; + drive-strength = <2>; + bias-disable; + output-high; + }; + }; +}; + +&blsp1_spi1 { /* BLSP1 QUP1 */ + pinctrl-0 = <&spi_0_pins>; + pinctrl-names = "default"; + status = "okay"; + cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>, + <&tlmm 59 GPIO_ACTIVE_HIGH>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <24000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + SBL1@0 { + label = "SBL1"; + reg = <0x00000000 0x00040000>; + read-only; + }; + MBIB@40000 { + label = "MIBIB"; + reg = <0x00040000 0x00020000>; + read-only; + }; + QSEE@60000 { + label = "QSEE"; + reg = <0x00060000 0x00060000>; + read-only; + }; + CDT@c0000 { + label = "CDT"; + reg = <0x000c0000 0x00010000>; + read-only; + }; + APPSBLENV@d0000 { + label = "APPSBLENV"; + reg = <0x000d0000 0x00010000>; + read-only; + }; + APPSBL@e0000 { + label = "APPSBL"; /* uboot */ + reg = <0x000e0000 0x00080000>; + read-only; + }; + ART@160000 { + label = "ART"; + reg = <0x00160000 0x00010000>; + read-only; + }; + u_env@170000 { + label = "u_env"; + reg = <0x00170000 0x00020000>; + }; + s_env@190000 { + label = "s_env"; + reg = <0x00190000 0x00020000>; + }; + devinfo@1b0000 { + label = "devinfo"; + reg = <0x001b0000 0x00010000>; + }; + /* 0x001c0000 - 0x00200000 unused */ + }; + }; + + flash@1 { + status = "okay"; + compatible = "spi-nand"; + reg = <1>; + spi-max-frequency = <24000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + kernel@0 { + label = "kernel"; + reg = <0x00000000 0x02800000>; + }; + rootfs@300000 { + label = "rootfs"; + reg = <0x00300000 0x02500000>; + }; + alt_kernel@2800000 { + label = "alt_kernel"; + reg = <0x02800000 0x02800000>; + }; + alt_rootfs@2b00000 { + label = "alt_rootfs"; + reg = <0x02b00000 0x02500000>; + }; + sysdiag@5000000 { + label = "sysdiag"; + reg = <0x05000000 0x00100000>; + }; + syscfg@5100000 { + label = "syscfg"; + reg = <0x05100000 0x02F00000>; + }; + /* 0x00000000 - 0x08000000: 128 MiB */ + }; + }; +}; + +&usb3_ss_phy { + status = "okay"; +}; + +&usb3_hs_phy { + status = "okay"; +}; + +&usb2_hs_phy { + status = "okay"; +}; -- cgit v1.2.3