From 6ee3680614047f7732731ebbaac946a93ab4f693 Mon Sep 17 00:00:00 2001 From: Dan Brown Date: Wed, 12 May 2021 14:48:01 +0200 Subject: octeon: add new target and support for Ubiquiti EdgeRouter 6P Ubiquiti EdgeRouter 6P is 6 port router with similar specifications as the EdgeRouter 4, support for which was added in commit dd651e54cc5eadba480a56a7d2c18471e560f491 There are five 10/100/1000 Mbps RJ/Copper ports and one 1000 Mbps SFP port. SoC: Octeon Cavium 7130 (Cavium 3) at 1000MHz Memory: 1GiB DDR3 Flash: 2x2M chips with uboots (chainloaded) + 512K eeprom LEDs: 1x for power status (white/blue, controllable) and 6x for ethernet and SFP ports (no control over them) Buttons: 1x Reset Serial: 1x RJ45 port on front panel. 115200 baud, 8N1 USB: 1x USB3.0 on front panel MII: 1x QSGMII from SoC PHY: 1x Vitesse VSC8504 of which 4 ports are used (phys 4-7) 1x Vitesse VSC8514 of which 2 ports are used (phys 8-9) Network port mapping - eth0 on device maps to lan0 and phy5 - eth1 on device maps to lan1 and phy6 - eth2 on device maps to lan2 and phy7 - eth3 on device maps to lan3 and phy8 - eth4 on device maps to lan4 and phy9 - eth5 (SFP) on device maps to lan5 and phy4 What is not working: - There is no port status available before it goes up - SFP have no additional status and presented as no different from eth - Power-over-ethernet (passive) support has not been tested How to flash the firmware: - copy openwrt-octeon-ubnt_edgerouter-6p-initramfs-kernel.bin and openwrt-octeon-ubnt_edgerouter-6p-squashfs-sysupgrade.tar to USB flash drive that is formatted to vfat/fat32 - connect USB flash drive to EdgeRouter 6P front USB port - connect serial cable using front RJ45 port (115200 baud, 8N1) - connect power to cable to EdgeRouter 6P - connect terminal to the console to see uboot boot process - interrupt boot by pressing button(s) on your keyboard to log in to the uboot - detect usb connected flash drives by typing to the console: usb start - after drive is detected load initramfs+kernel to the memory by typing: fatload usb 0:1 0x20000000 openwrt-octeon-ubnt_edgerouter-6p-initramfs-kernel.bin - after initramfs+kernel is loaded to the memory load it by typing: bootoctlinux 0 numcores=4 endbootargs mem=0 - boot process should finish and you will be greeted with console after pressing enter - create directory to mount usb flash drive to by typing: mkdir /tmp/sda - mount flash drive to that directory by typing: mount /dev/sda1 /tmp/sda - flash firmware to router internal storage by typing: sysupgrade /tmp/sda/openwrt-octeon-ubnt_edgerouter-6p-squashfs-sysupgrade.tar - device will reboot and after it gets up you will have edgerouter 6p running openwrt Signed-off-by: Dan Brown [reorder/squash patches, move ethernet@0 to DTS, share image setup] Signed-off-by: Adrian Schmutzler --- target/linux/octeon/image/Makefile | 17 ++++++++++++++--- 1 file changed, 14 insertions(+), 3 deletions(-) (limited to 'target/linux/octeon/image') diff --git a/target/linux/octeon/image/Makefile b/target/linux/octeon/image/Makefile index 11da22df3b..f77159e1f9 100644 --- a/target/linux/octeon/image/Makefile +++ b/target/linux/octeon/image/Makefile @@ -51,17 +51,28 @@ define Device/ubnt_edgerouter endef TARGET_DEVICES += ubnt_edgerouter -define Device/ubnt_edgerouter-4 +define Device/ubnt_edgerouter-e300 DEVICE_VENDOR := Ubiquiti - DEVICE_MODEL := EdgeRouter 4 - DEVICE_DTS := cn7130_ubnt_edgerouter-4 DEVICE_PACKAGES += kmod-gpio-button-hotplug kmod-leds-gpio kmod-of-mdio kmod-sfp kmod-usb3 kmod-usb-dwc3 kmod-usb-storage-uas KERNEL := kernel-bin | patch-cmdline | append-dtb-to-elf KERNEL_DEPENDS := $$(wildcard $(DTS_DIR)/$(DEVICE_DTS).dts) CMDLINE := root=/dev/mmcblk0p2 rootfstype=squashfs,ext4 rootwait endef + +define Device/ubnt_edgerouter-4 + $(Device/ubnt_edgerouter-e300) + DEVICE_MODEL := EdgeRouter 4 + DEVICE_DTS := cn7130_ubnt_edgerouter-4 +endef TARGET_DEVICES += ubnt_edgerouter-4 +define Device/ubnt_edgerouter-6p + $(Device/ubnt_edgerouter-e300) + DEVICE_MODEL := EdgeRouter 6P + DEVICE_DTS := cn7130_ubnt_edgerouter-6p +endef +TARGET_DEVICES += ubnt_edgerouter-6p + ERLITE_CMDLINE:=-mtdparts=phys_mapped_flash:512k(boot0)ro,512k(boot1)ro,64k(eeprom)ro root=/dev/sda2 rootfstype=squashfs,ext4 rootwait define Device/ubnt_edgerouter-lite DEVICE_VENDOR := Ubiquiti -- cgit v1.2.3