From e9a9b7d1ed76c88e097d5bc4dabf38735312558b Mon Sep 17 00:00:00 2001 From: Pawel Dembicki Date: Wed, 24 Oct 2018 14:06:35 +0200 Subject: ramips: add support for D-Link DWR-118-A1 The DWR-118-A1 Wireless Router is based on the MT7620A SoC. Specification: - MediaTek MT7620A (580 Mhz) - 64 MB of RAM - 16 MB of FLASH - 1x 802.11bgn radio - 1x 802.11ac radio (MT7610EN) - 3x 10/100 Mbps Ethernet (3 LAN) - 2x 10/100/1000 Mbps ICPlus IP1001 Ethernet PHY (1 WAN AND 1 LAN) - 1x internal, non-detachable antenna - 2x external, non-detachable antennas - 1x USB 2.0 - UART (J1) header on PCB (57600 8n1) - 7x LED (5x GPIO-controlled), 2x button - JBOOT bootloader Known issues: - WIFI 5G LED not working - flash is very slow The status led has been assigned to the dwr-118-a1:green:internet led. At the end of the boot it is switched off and is available for other operation. Work correctly also during sysupgrade operation. Installation: Apply factory image via http web-gui or JBOOT recovery page How to revert to OEM firmware: - push the reset button and turn on the power. Wait until LED start blinking (~10sec.) - upload original factory image via JBOOT http (IP: 192.168.123.254) Signed-off-by: Pawel Dembicki --- target/linux/ramips/base-files/etc/board.d/01_leds | 5 +++++ target/linux/ramips/base-files/etc/board.d/02_network | 5 +++++ 2 files changed, 10 insertions(+) (limited to 'target/linux/ramips/base-files/etc/board.d') diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds index b2c69d4b59..f8c4b05b9a 100755 --- a/target/linux/ramips/base-files/etc/board.d/01_leds +++ b/target/linux/ramips/base-files/etc/board.d/01_leds @@ -114,6 +114,11 @@ dlink,dwr-116-a1|\ mzk-ex300np) set_wifi_led "$boardname:green:wifi" ;; +dlink,dwr-118-a1) + ucidef_set_led_switch "lan" "lan" "$boardname:green:lan" "switch0" "0x1f" + ucidef_set_led_switch "wan" "wan" "$boardname:green:wan" "switch0" "0x20" + set_wifi_led "$boardname:green:wlan2g" "wlan1" + ;; dlink,dwr-118-a2) ucidef_set_led_switch "lan" "lan" "$boardname:green:lan" "switch0" "0x0e" ucidef_set_led_switch "wan" "wan" "$boardname:green:wan" "switch0" "0x01" diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network index 3af836a6f3..c207b7cad4 100755 --- a/target/linux/ramips/base-files/etc/board.d/02_network +++ b/target/linux/ramips/base-files/etc/board.d/02_network @@ -162,6 +162,10 @@ ramips_setup_interfaces() wrh-300cr) ucidef_set_interface_lan "eth0" ;; + dlink,dwr-118-a1) + ucidef_add_switch "switch0" \ + "1:lan:2" "2:lan:3" "3:lan:1" "4:lan:0" "5:wan" "6@eth0" + ;; dlink,dwr-118-a2) ucidef_add_switch "switch0" \ "1:lan:2" "2:lan:1" "3:lan:3" "4:lan" "0:wan" "6@eth0" @@ -475,6 +479,7 @@ ramips_setup_macs() wan_mac=$(mtd_get_mac_ascii factory wanmac) ;; dlink,dwr-116-a1|\ + dlink,dwr-118-a1|\ dlink,dwr-118-a2|\ dlink,dwr-921-c1|\ lava,lr-25g001) -- cgit v1.2.3