From abbfcc85259a4f6658c61e99dd3d2d3567e3eb3a Mon Sep 17 00:00:00 2001 From: Kyson Lok Date: Wed, 17 May 2017 18:18:45 +0800 Subject: ramips: add support for GL-inet GL-MT300N-V2 This patch adds supports for the GL-inet GL-MT300N-V2. Specification: - SoC: MediaTek MT7628AN - Flash: 16 MiB (W25Q128FVSG) - RAM: 128 MiB DDR - Ethernet: 1 x WAN (100 Mbps) and 1 x LAN (100 Mbps) - USB: 1 x USB 2.0 port - Button: 1 x switch button, 1 x reset button - LED: 3 x LEDS (system power led is not GPIO controller) - UART: 1 x UART on PCB (JP1: 3.3V, RX, TX, GND) Installation through Luci: - The original firmware is LEDE, so both LuCI or sysupgrade can be used. - Do not keep settings, for sysupgrade please use the -n option. Installation through bootloader webserver: - Plug power and hold reset button until red LED blink to bright. - Install sysupgrade image using web interface on 192.168.1.1. Signed-off-by: Kyson Lok [match maximum image size with firmware partition] Signed-off-by: Mathias Kresin --- target/linux/ramips/base-files/etc/board.d/01_leds | 3 +++ target/linux/ramips/base-files/etc/board.d/02_network | 4 ++++ target/linux/ramips/base-files/etc/diag.sh | 3 +++ 3 files changed, 10 insertions(+) (limited to 'target/linux/ramips/base-files/etc') diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds index 2a35fc4bc2..b08f35268b 100755 --- a/target/linux/ramips/base-files/etc/board.d/01_leds +++ b/target/linux/ramips/base-files/etc/board.d/01_leds @@ -189,6 +189,9 @@ gl-mt300n|\ gl-mt750) set_wifi_led "$board:wlan" ;; +gl-mt300n-v2) + set_wifi_led "$board:red:wlan" + ;; hc5661|\ hc5661a) ucidef_set_led_default "system" "system" "$board:blue:system" "1" diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network index 6d93f2ccaa..9dd5823639 100755 --- a/target/linux/ramips/base-files/etc/board.d/02_network +++ b/target/linux/ramips/base-files/etc/board.d/02_network @@ -180,6 +180,10 @@ ramips_setup_interfaces() ucidef_add_switch "switch0" \ "1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "6@eth0" ;; + gl-mt300n-v2) + ucidef_add_switch "switch0" \ + "1:lan" "0:wan" "6@eth0" + ;; awapn2403) ucidef_add_switch "switch0" \ "0:lan" "1:wan" "6@eth0" diff --git a/target/linux/ramips/base-files/etc/diag.sh b/target/linux/ramips/base-files/etc/diag.sh index e37f9cfda4..26d7f627cd 100644 --- a/target/linux/ramips/base-files/etc/diag.sh +++ b/target/linux/ramips/base-files/etc/diag.sh @@ -166,6 +166,9 @@ get_status_led() { miwifi-nano) status_led="$board:blue:status" ;; + gl-mt300n-v2) + status_led="$board:red:wlan" + ;; m4-4M|\ m4-8M) status_led="m4:blue:status" -- cgit v1.2.3