From 9715beb04c74a918697945b3e2d23a139bd04b70 Mon Sep 17 00:00:00 2001 From: Sven Roederer Date: Mon, 29 May 2017 11:24:49 +0200 Subject: ramips: add support for Ubiquiti EdgeRouter X-SFP This patch adds support for the Ubiquiti EdgeRouter X-SFP and improves support for the EdgeRouter X (PoE-passthrough). Specification: - SoC: MediaTek MT7621AT - Flash: 256 MiB - RAM: 265 MiB - Ethernet: 5 x LAN (1000 Mbps) - UART: 1 x UART on PCB (3.3V, RX, TX, GND) - 57600 8N1 - EdgeRouter X: - 1 x PoE-Passtrough (Eth4) - powered by Wallwart or passive PoE - EdgeRouter X-SFP: - 5 x PoE-Out (24V, passive) - 1 x SFP (unknown status) - powered by Wallwart (24V) Doesn't work: * SoC has crypto engine but no open driver. * SoC has nat acceleration, but no open driver. * This router has 2MB spi flash soldered in but MT nand/spi drivers do not support pin sharing, so it is not accessable and disabled. Stock firmware could read it and it was empty. Installation via vendor firmware: - build an Initrd-image (> 3MiB) and upload the factory-image - initrd can have luci-mod-failsafe - flash final firmware via LuCI / sysupgrade on rebooted system via TFTP: - stop uboot into tftp-load into option "1" - upload factory.bin image Signed-off-by: Sven Roederer --- target/linux/ramips/base-files/lib/ramips.sh | 3 +++ target/linux/ramips/base-files/lib/upgrade/platform.sh | 9 ++++++--- 2 files changed, 9 insertions(+), 3 deletions(-) (limited to 'target/linux/ramips/base-files/lib') diff --git a/target/linux/ramips/base-files/lib/ramips.sh b/target/linux/ramips/base-files/lib/ramips.sh index 4b60a07ee0..c8865fc298 100755 --- a/target/linux/ramips/base-files/lib/ramips.sh +++ b/target/linux/ramips/base-files/lib/ramips.sh @@ -487,6 +487,9 @@ ramips_board_detect() { *"UBNT-ERX") name="ubnt-erx" ;; + *"UBNT-ERX-SFP") + name="ubnt-erx-sfp" + ;; *"UR-326N4G") name="ur-326n4g" ;; diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh index f25d1e2a62..dce4c1a327 100755 --- a/target/linux/ramips/base-files/lib/upgrade/platform.sh +++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh @@ -252,7 +252,8 @@ platform_check_image() { # these boards use metadata images return 0 ;; - ubnt-erx) + ubnt-erx|\ + ubnt-erx-sfp) nand_do_platform_check "$board" "$1" return $?; ;; @@ -274,7 +275,8 @@ platform_nand_pre_upgrade() { local board=$(ramips_board_name) case "$board" in - ubnt-erx) + ubnt-erx|\ + ubnt-erx-sfp) platform_upgrade_ubnt_erx "$ARGV" ;; esac @@ -286,7 +288,8 @@ platform_do_upgrade() { case "$board" in hc5962|\ r6220|\ - ubnt-erx) + ubnt-erx|\ + ubnt-erx-sfp) nand_do_upgrade "$ARGV" ;; *) -- cgit v1.2.3