From c70545f397187b36c1220ae16b4db19f39857c93 Mon Sep 17 00:00:00 2001 From: DENG Qingfang Date: Sun, 1 Mar 2020 17:01:09 +0800 Subject: ramips: copy patches and kernel config to 5.4 Copy patches and kernel config to 5.4 for ramips Signed-off-by: DENG Qingfang --- target/linux/ramips/mt7621/config-5.4 | 315 ++ ...001-MIPS-ralink-Add-rt3352-SPI_CS1-pinmux.patch | 45 + ...IPS-pci-rt2880-set-pci-controller-of_node.patch | 32 + ...mory-reservation-in-bootmem_init-for-cert.patch | 45 + .../0004-MIPS-ralink-add-MT7621-pcie-driver.patch | 861 ++++ ...t_mode-to-enable-disable-the-cevt-r4k-irq.patch | 82 + ...006-MIPS-ralink-add-cpu-frequency-scaling.patch | 200 + ...-copy-the-commandline-from-the-devicetree.patch | 21 + .../0009-PCI-MIPS-enable-PCIe-on-MT7688.patch | 28 + .../0013-owrt-hack-fix-mt7688-cache-issue.patch | 28 + ...o-not-select-illegal-access-driver-by-def.patch | 25 + .../0024-GPIO-add-named-gpio-exports.patch | 165 + .../0025-pinctrl-ralink-add-pinctrl-driver.patch | 524 +++ ...0026-DT-Add-documentation-for-gpio-ralink.patch | 59 + ...IPS-ralink-add-gpio-driver-for-ralink-SoC.patch | 430 ++ ...28-GPIO-ralink-add-mt7621-gpio-controller.patch | 405 ++ ...-Add-support-for-GPIO-as-interrupt-contro.patch | 44 + .../0031-uvc-add-iPassion-iP2970-support.patch | 246 ++ .../0032-USB-dwc2-add-device_reset.patch | 29 + .../patches-5.4/0034-NET-multi-phy-support.patch | 59 + ...0037-mtd-cfi-cmdset-0002-force-word-write.patch | 70 + ...d-nand-Remove-unused-chip-write_page-hook.patch | 67 + .../0039-mtd-add-mt7621-nand-support.patch | 4437 ++++++++++++++++++++ .../linux/ramips/patches-5.4/0040-nand-hack.patch | 32 + .../0041-DT-Add-documentation-for-spi-rt2880.patch | 44 + ...0042-SPI-ralink-add-Ralink-SoC-spi-driver.patch | 574 +++ .../patches-5.4/0043-spi-add-mt7621-support.patch | 487 +++ .../0044-i2c-MIPS-adds-ralink-I2C-driver.patch | 507 +++ .../patches-5.4/0045-i2c-add-mt7621-driver.patch | 473 +++ ...mmc-MIPS-ralink-add-sdhci-for-mt7620a-SoC.patch | 43 + .../0047-DMA-ralink-add-rt2880-dma-engine.patch | 1757 ++++++++ .../patches-5.4/0048-asoc-add-mt7620-support.patch | 1046 +++++ ...051-serial-add-ugly-custom-baud-rate-hack.patch | 22 + .../0052-pwm-add-mediatek-support.patch | 217 + ...53-mtd-spi-nor-add-w25q256-3b-mode-switch.patch | 214 + ...-mtd-spi-nor-w25q256-respect-default-mode.patch | 73 + .../0069-awake-rt305x-dwc2-controller.patch | 15 + .../ramips/patches-5.4/0070-weak_reordering.patch | 10 + .../linux/ramips/patches-5.4/0098-disable_cm.patch | 19 + .../linux/ramips/patches-5.4/0099-pci-mt7620.patch | 10 + .../ramips/patches-5.4/0200-linkit_bootstrap.patch | 97 + .../patches-5.4/100-mt7621-core-detect-hack.patch | 61 + .../ramips/patches-5.4/101-mt7621-timer.patch | 87 + .../102-mt7621-fix-cpu-clk-add-clkdev.patch | 224 + .../patches-5.4/105-mt7621-memory-detect.patch | 125 + .../patches-5.4/110-mt7621-perfctr-fix.patch | 15 + .../300-mt7620-export-chip-version-and-pkg.patch | 19 + .../patches-5.4/302-spi-nor-add-gd25q512.patch | 14 + ...spi-nor-enable-4B-opcodes-for-mx25l25635f.patch | 72 + .../patches-5.4/999-fix-pci-init-mt7620.patch | 21 + 50 files changed, 14495 insertions(+) create mode 100644 target/linux/ramips/mt7621/config-5.4 create mode 100644 target/linux/ramips/patches-5.4/0001-MIPS-ralink-Add-rt3352-SPI_CS1-pinmux.patch create mode 100644 target/linux/ramips/patches-5.4/0002-MIPS-pci-rt2880-set-pci-controller-of_node.patch create mode 100644 target/linux/ramips/patches-5.4/0003-MIPS-Fix-memory-reservation-in-bootmem_init-for-cert.patch create mode 100644 target/linux/ramips/patches-5.4/0004-MIPS-ralink-add-MT7621-pcie-driver.patch create mode 100644 target/linux/ramips/patches-5.4/0005-MIPS-use-set_mode-to-enable-disable-the-cevt-r4k-irq.patch create mode 100644 target/linux/ramips/patches-5.4/0006-MIPS-ralink-add-cpu-frequency-scaling.patch create mode 100644 target/linux/ramips/patches-5.4/0007-MIPS-ralink-copy-the-commandline-from-the-devicetree.patch create mode 100644 target/linux/ramips/patches-5.4/0009-PCI-MIPS-enable-PCIe-on-MT7688.patch create mode 100644 target/linux/ramips/patches-5.4/0013-owrt-hack-fix-mt7688-cache-issue.patch create mode 100644 target/linux/ramips/patches-5.4/0015-arch-mips-do-not-select-illegal-access-driver-by-def.patch create mode 100644 target/linux/ramips/patches-5.4/0024-GPIO-add-named-gpio-exports.patch create mode 100644 target/linux/ramips/patches-5.4/0025-pinctrl-ralink-add-pinctrl-driver.patch create mode 100644 target/linux/ramips/patches-5.4/0026-DT-Add-documentation-for-gpio-ralink.patch create mode 100644 target/linux/ramips/patches-5.4/0027-GPIO-MIPS-ralink-add-gpio-driver-for-ralink-SoC.patch create mode 100644 target/linux/ramips/patches-5.4/0028-GPIO-ralink-add-mt7621-gpio-controller.patch create mode 100644 target/linux/ramips/patches-5.4/0029-gpio-ralink-Add-support-for-GPIO-as-interrupt-contro.patch create mode 100644 target/linux/ramips/patches-5.4/0031-uvc-add-iPassion-iP2970-support.patch create mode 100644 target/linux/ramips/patches-5.4/0032-USB-dwc2-add-device_reset.patch create mode 100644 target/linux/ramips/patches-5.4/0034-NET-multi-phy-support.patch create mode 100644 target/linux/ramips/patches-5.4/0037-mtd-cfi-cmdset-0002-force-word-write.patch create mode 100644 target/linux/ramips/patches-5.4/0038-Revert-mtd-nand-Remove-unused-chip-write_page-hook.patch create mode 100644 target/linux/ramips/patches-5.4/0039-mtd-add-mt7621-nand-support.patch create mode 100644 target/linux/ramips/patches-5.4/0040-nand-hack.patch create mode 100644 target/linux/ramips/patches-5.4/0041-DT-Add-documentation-for-spi-rt2880.patch create mode 100644 target/linux/ramips/patches-5.4/0042-SPI-ralink-add-Ralink-SoC-spi-driver.patch create mode 100644 target/linux/ramips/patches-5.4/0043-spi-add-mt7621-support.patch create mode 100644 target/linux/ramips/patches-5.4/0044-i2c-MIPS-adds-ralink-I2C-driver.patch create mode 100644 target/linux/ramips/patches-5.4/0045-i2c-add-mt7621-driver.patch create mode 100644 target/linux/ramips/patches-5.4/0046-mmc-MIPS-ralink-add-sdhci-for-mt7620a-SoC.patch create mode 100644 target/linux/ramips/patches-5.4/0047-DMA-ralink-add-rt2880-dma-engine.patch create mode 100644 target/linux/ramips/patches-5.4/0048-asoc-add-mt7620-support.patch create mode 100644 target/linux/ramips/patches-5.4/0051-serial-add-ugly-custom-baud-rate-hack.patch create mode 100644 target/linux/ramips/patches-5.4/0052-pwm-add-mediatek-support.patch create mode 100644 target/linux/ramips/patches-5.4/0053-mtd-spi-nor-add-w25q256-3b-mode-switch.patch create mode 100644 target/linux/ramips/patches-5.4/0054-mtd-spi-nor-w25q256-respect-default-mode.patch create mode 100644 target/linux/ramips/patches-5.4/0069-awake-rt305x-dwc2-controller.patch create mode 100644 target/linux/ramips/patches-5.4/0070-weak_reordering.patch create mode 100644 target/linux/ramips/patches-5.4/0098-disable_cm.patch create mode 100644 target/linux/ramips/patches-5.4/0099-pci-mt7620.patch create mode 100644 target/linux/ramips/patches-5.4/0200-linkit_bootstrap.patch create mode 100644 target/linux/ramips/patches-5.4/100-mt7621-core-detect-hack.patch create mode 100644 target/linux/ramips/patches-5.4/101-mt7621-timer.patch create mode 100644 target/linux/ramips/patches-5.4/102-mt7621-fix-cpu-clk-add-clkdev.patch create mode 100644 target/linux/ramips/patches-5.4/105-mt7621-memory-detect.patch create mode 100644 target/linux/ramips/patches-5.4/110-mt7621-perfctr-fix.patch create mode 100644 target/linux/ramips/patches-5.4/300-mt7620-export-chip-version-and-pkg.patch create mode 100644 target/linux/ramips/patches-5.4/302-spi-nor-add-gd25q512.patch create mode 100644 target/linux/ramips/patches-5.4/304-spi-nor-enable-4B-opcodes-for-mx25l25635f.patch create mode 100644 target/linux/ramips/patches-5.4/999-fix-pci-init-mt7620.patch (limited to 'target/linux') diff --git a/target/linux/ramips/mt7621/config-5.4 b/target/linux/ramips/mt7621/config-5.4 new file mode 100644 index 0000000000..4112cad780 --- /dev/null +++ b/target/linux/ramips/mt7621/config-5.4 @@ -0,0 +1,315 @@ +CONFIG_ARCH_BINFMT_ELF_STATE=y +CONFIG_ARCH_CLOCKSOURCE_DATA=y +CONFIG_ARCH_DISCARD_MEMBLOCK=y +CONFIG_ARCH_HAS_ELF_RANDOMIZE=y +# CONFIG_ARCH_HAS_GCOV_PROFILE_ALL is not set +CONFIG_ARCH_HAS_RESET_CONTROLLER=y +# CONFIG_ARCH_HAS_SG_CHAIN is not set +# CONFIG_ARCH_HAS_STRICT_KERNEL_RWX is not set +# CONFIG_ARCH_HAS_STRICT_MODULE_RWX is not set +CONFIG_ARCH_HAS_TICK_BROADCAST=y +CONFIG_ARCH_HIBERNATION_POSSIBLE=y +CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y +CONFIG_ARCH_MIGHT_HAVE_PC_SERIO=y +CONFIG_ARCH_MMAP_RND_BITS_MAX=15 +CONFIG_ARCH_MMAP_RND_COMPAT_BITS_MAX=15 +# CONFIG_ARCH_OPTIONAL_KERNEL_RWX is not set +# CONFIG_ARCH_OPTIONAL_KERNEL_RWX_DEFAULT is not set +CONFIG_ARCH_SUPPORTS_UPROBES=y +CONFIG_ARCH_SUSPEND_POSSIBLE=y +CONFIG_ARCH_USE_BUILTIN_BSWAP=y +CONFIG_ARCH_USE_QUEUED_RWLOCKS=y +CONFIG_ARCH_USE_QUEUED_SPINLOCKS=y +CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y +CONFIG_BLK_MQ_PCI=y +CONFIG_BOARD_SCACHE=y +CONFIG_BOUNCE=y +CONFIG_CEVT_R4K=y +# CONFIG_CEVT_SYSTICK_QUIRK is not set +CONFIG_CLKDEV_LOOKUP=y +CONFIG_CLKSRC_MIPS_GIC=y +CONFIG_CLONE_BACKWARDS=y +CONFIG_CMDLINE="rootfstype=squashfs,jffs2" +CONFIG_CMDLINE_BOOL=y +# CONFIG_CMDLINE_OVERRIDE is not set +CONFIG_COMMON_CLK=y +# CONFIG_COMMON_CLK_BOSTON is not set +CONFIG_CPU_GENERIC_DUMP_TLB=y +CONFIG_CPU_HAS_PREFETCH=y +CONFIG_CPU_HAS_RIXI=y +CONFIG_CPU_HAS_SYNC=y +CONFIG_CPU_LITTLE_ENDIAN=y +CONFIG_CPU_MIPS32=y +# CONFIG_CPU_MIPS32_R1 is not set +CONFIG_CPU_MIPS32_R2=y +CONFIG_CPU_MIPSR2=y +CONFIG_CPU_MIPSR2_IRQ_EI=y +CONFIG_CPU_MIPSR2_IRQ_VI=y +CONFIG_CPU_NEEDS_NO_SMARTMIPS_OR_MICROMIPS=y +CONFIG_CPU_R4K_CACHE_TLB=y +CONFIG_CPU_R4K_FPU=y +CONFIG_CPU_RMAP=y +CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y +CONFIG_CPU_SUPPORTS_HIGHMEM=y +CONFIG_CPU_SUPPORTS_MSA=y +CONFIG_CRC16=y +CONFIG_CRYPTO_ACOMP2=y +CONFIG_CRYPTO_AEAD=y +CONFIG_CRYPTO_AEAD2=y +CONFIG_CRYPTO_DEFLATE=y +CONFIG_CRYPTO_HASH2=y +CONFIG_CRYPTO_LZO=y +CONFIG_CRYPTO_MANAGER=y +CONFIG_CRYPTO_MANAGER2=y +CONFIG_CRYPTO_NULL2=y +CONFIG_CRYPTO_RNG2=y +CONFIG_CRYPTO_WORKQUEUE=y +CONFIG_CSRC_R4K=y +CONFIG_DEBUG_PINCTRL=y +CONFIG_DMA_NONCOHERENT=y +CONFIG_DTB_RT_NONE=y +CONFIG_DTC=y +CONFIG_EARLY_PRINTK=y +CONFIG_FIXED_PHY=y +CONFIG_GENERIC_ATOMIC64=y +CONFIG_GENERIC_CLOCKEVENTS=y +CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_CPU_AUTOPROBE=y +CONFIG_GENERIC_IO=y +CONFIG_GENERIC_IRQ_CHIP=y +CONFIG_GENERIC_IRQ_EFFECTIVE_AFF_MASK=y +CONFIG_GENERIC_IRQ_IPI=y +CONFIG_GENERIC_IRQ_SHOW=y +CONFIG_GENERIC_PCI_IOMAP=y +CONFIG_GENERIC_SCHED_CLOCK=y +CONFIG_GENERIC_SMP_IDLE_THREAD=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GPIOLIB=y +CONFIG_GPIO_MT7621=y +# CONFIG_GPIO_RALINK is not set +CONFIG_GPIO_SYSFS=y +CONFIG_GPIO_WATCHDOG=y +# CONFIG_GPIO_WATCHDOG_ARCH_INITCALL is not set +# CONFIG_GRO_CELLS is not set +CONFIG_HANDLE_DOMAIN_IRQ=y +CONFIG_HARDWARE_WATCHPOINTS=y +CONFIG_HAS_DMA=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT_MAP=y +# CONFIG_HAVE_64BIT_ALIGNED_ACCESS is not set +# CONFIG_HAVE_ARCH_BITREVERSE is not set +CONFIG_HAVE_ARCH_COMPILER_H=y +CONFIG_HAVE_ARCH_JUMP_LABEL=y +CONFIG_HAVE_ARCH_KGDB=y +CONFIG_HAVE_ARCH_SECCOMP_FILTER=y +CONFIG_HAVE_ARCH_TRACEHOOK=y +# CONFIG_HAVE_BOOTMEM_INFO_NODE is not set +CONFIG_HAVE_CBPF_JIT=y +CONFIG_HAVE_CC_STACKPROTECTOR=y +CONFIG_HAVE_CLK=y +CONFIG_HAVE_CLK_PREPARE=y +CONFIG_HAVE_CONTEXT_TRACKING=y +CONFIG_HAVE_COPY_THREAD_TLS=y +CONFIG_HAVE_C_RECORDMCOUNT=y +CONFIG_HAVE_DEBUG_KMEMLEAK=y +CONFIG_HAVE_DEBUG_STACKOVERFLOW=y +CONFIG_HAVE_DMA_API_DEBUG=y +CONFIG_HAVE_DMA_CONTIGUOUS=y +CONFIG_HAVE_DYNAMIC_FTRACE=y +CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y +CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y +CONFIG_HAVE_FUNCTION_TRACER=y +CONFIG_HAVE_GENERIC_DMA_COHERENT=y +CONFIG_HAVE_IDE=y +CONFIG_HAVE_IRQ_EXIT_ON_IRQ_STACK=y +CONFIG_HAVE_IRQ_TIME_ACCOUNTING=y +CONFIG_HAVE_KVM=y +CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_HAVE_MEMBLOCK=y +CONFIG_HAVE_MEMBLOCK_NODE_MAP=y +CONFIG_HAVE_MOD_ARCH_SPECIFIC=y +CONFIG_HAVE_NET_DSA=y +CONFIG_HAVE_OPROFILE=y +CONFIG_HAVE_PERF_EVENTS=y +CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y +CONFIG_HAVE_SYSCALL_TRACEPOINTS=y +CONFIG_HIGHMEM=y +CONFIG_HW_HAS_PCI=y +CONFIG_HZ_PERIODIC=y +CONFIG_I2C=y +CONFIG_I2C_BOARDINFO=y +CONFIG_I2C_MT7621=y +CONFIG_INITRAMFS_SOURCE="" +CONFIG_IRQCHIP=y +CONFIG_IRQ_DOMAIN=y +CONFIG_IRQ_DOMAIN_HIERARCHY=y +CONFIG_IRQ_FORCED_THREADING=y +CONFIG_IRQ_MIPS_CPU=y +CONFIG_IRQ_WORK=y +CONFIG_LIBFDT=y +CONFIG_LZO_COMPRESS=y +CONFIG_LZO_DECOMPRESS=y +CONFIG_MDIO_BUS=y +CONFIG_MDIO_DEVICE=y +CONFIG_MIGRATION=y +CONFIG_MIPS=y +CONFIG_MIPS_ASID_BITS=8 +CONFIG_MIPS_ASID_SHIFT=0 +CONFIG_MIPS_CBPF_JIT=y +CONFIG_MIPS_CLOCK_VSYSCALL=y +CONFIG_MIPS_CM=y +# CONFIG_MIPS_CMDLINE_BUILTIN_EXTEND is not set +# CONFIG_MIPS_CMDLINE_DTB_EXTEND is not set +# CONFIG_MIPS_CMDLINE_FROM_BOOTLOADER is not set +CONFIG_MIPS_CMDLINE_FROM_DTB=y +CONFIG_MIPS_CPC=y +CONFIG_MIPS_CPS=y +# CONFIG_MIPS_CPS_NS16550 is not set +CONFIG_MIPS_CPU_SCACHE=y +# CONFIG_MIPS_ELF_APPENDED_DTB is not set +CONFIG_MIPS_GIC=y +# CONFIG_MIPS_HUGE_TLB_SUPPORT is not set +CONFIG_MIPS_L1_CACHE_SHIFT=5 +# CONFIG_MIPS_MACHINE is not set +CONFIG_MIPS_MT=y +CONFIG_MIPS_MT_FPAFF=y +CONFIG_MIPS_MT_SMP=y +# CONFIG_MIPS_NO_APPENDED_DTB is not set +CONFIG_MIPS_PERF_SHARED_TC_COUNTERS=y +CONFIG_MIPS_RAW_APPENDED_DTB=y +CONFIG_MIPS_SPRAM=y +# CONFIG_MIPS_VPE_LOADER is not set +CONFIG_MODULES_USE_ELF_REL=y +CONFIG_MT7621_WDT=y +# CONFIG_MTD_CFI_INTELEXT is not set +CONFIG_MTD_CMDLINE_PARTS=y +CONFIG_MTD_M25P80=y +CONFIG_MTD_NAND=y +CONFIG_MTD_NAND_ECC=y +CONFIG_MTD_PHYSMAP=y +CONFIG_MTD_SPI_NOR=y +CONFIG_MTD_SPLIT_MINOR_FW=y +CONFIG_MTD_SPLIT_SEAMA_FW=y +CONFIG_MTD_SPLIT_TPLINK_FW=y +CONFIG_MTD_SPLIT_TRX_FW=y +CONFIG_MTD_SPLIT_UIMAGE_FW=y +CONFIG_MTD_UBI=y +CONFIG_MTD_UBI_BEB_LIMIT=20 +CONFIG_MTD_UBI_BLOCK=y +# CONFIG_MTD_UBI_FASTMAP is not set +# CONFIG_MTD_UBI_GLUEBI is not set +CONFIG_MTD_UBI_WL_THRESHOLD=4096 +CONFIG_MTK_MTD_NAND=y +CONFIG_NEED_DMA_MAP_STATE=y +CONFIG_NET_FLOW_LIMIT=y +CONFIG_NET_MEDIATEK_GSW_MT7621=y +CONFIG_NET_MEDIATEK_MDIO=y +CONFIG_NET_MEDIATEK_MDIO_MT7620=y +CONFIG_NET_MEDIATEK_MT7621=y +CONFIG_NET_MEDIATEK_OFFLOAD=y +CONFIG_NET_MEDIATEK_SOC=y +CONFIG_NET_VENDOR_MEDIATEK=y +CONFIG_NO_GENERIC_PCI_IOPORT_MAP=y +# CONFIG_NO_IOPORT_MAP is not set +CONFIG_NR_CPUS=4 +CONFIG_OF=y +CONFIG_OF_ADDRESS=y +CONFIG_OF_ADDRESS_PCI=y +CONFIG_OF_EARLY_FLATTREE=y +CONFIG_OF_FLATTREE=y +CONFIG_OF_GPIO=y +CONFIG_OF_IRQ=y +CONFIG_OF_MDIO=y +CONFIG_OF_NET=y +CONFIG_OF_PCI=y +CONFIG_OF_PCI_IRQ=y +CONFIG_PADATA=y +CONFIG_PCI=y +CONFIG_PCI_DISABLE_COMMON_QUIRKS=y +CONFIG_PCI_DOMAINS=y +CONFIG_PCI_DRIVERS_LEGACY=y +CONFIG_PERF_USE_VMALLOC=y +CONFIG_PGTABLE_LEVELS=2 +CONFIG_PHYLIB=y +# CONFIG_PHY_RALINK_USB is not set +CONFIG_PINCTRL=y +CONFIG_PINCTRL_RT2880=y +# CONFIG_PINCTRL_SINGLE is not set +CONFIG_POWER_RESET=y +CONFIG_POWER_RESET_GPIO=y +CONFIG_POWER_SUPPLY=y +CONFIG_QUEUED_RWLOCKS=y +CONFIG_QUEUED_SPINLOCKS=y +CONFIG_RALINK=y +# CONFIG_RALINK_WDT is not set +CONFIG_RATIONAL=y +CONFIG_RCU_NEED_SEGCBLIST=y +CONFIG_RCU_STALL_COMMON=y +CONFIG_REGMAP=y +CONFIG_REGMAP_I2C=y +CONFIG_REGMAP_SPI=y +CONFIG_REGULATOR=y +CONFIG_REGULATOR_FIXED_VOLTAGE=y +CONFIG_RESET_CONTROLLER=y +CONFIG_RFS_ACCEL=y +CONFIG_RPS=y +CONFIG_RTC_CLASS=y +CONFIG_RTC_DRV_BQ32K=y +CONFIG_RTC_DRV_PCF8563=y +CONFIG_RTC_I2C_AND_SPI=y +CONFIG_RTC_MC146818_LIB=y +# CONFIG_SCHED_INFO is not set +CONFIG_SCHED_SMT=y +# CONFIG_SCSI_DMA is not set +# CONFIG_SERIAL_8250_FSL is not set +CONFIG_SERIAL_8250_NR_UARTS=3 +CONFIG_SERIAL_8250_RUNTIME_UARTS=3 +CONFIG_SERIAL_OF_PLATFORM=y +CONFIG_SMP=y +CONFIG_SMP_UP=y +# CONFIG_SOC_MT7620 is not set +CONFIG_SOC_MT7621=y +# CONFIG_SOC_RT288X is not set +# CONFIG_SOC_RT305X is not set +# CONFIG_SOC_RT3883 is not set +CONFIG_SPI=y +CONFIG_SPI_MASTER=y +CONFIG_SPI_MT7621=y +# CONFIG_SPI_RT2880 is not set +CONFIG_SRCU=y +CONFIG_SWCONFIG=y +CONFIG_SWCONFIG_LEDS=y +CONFIG_SWPHY=y +CONFIG_SYNC_R4K=y +CONFIG_SYSCTL_EXCEPTION_TRACE=y +CONFIG_SYS_HAS_CPU_MIPS32_R1=y +CONFIG_SYS_HAS_CPU_MIPS32_R2=y +CONFIG_SYS_HAS_EARLY_PRINTK=y +CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y +CONFIG_SYS_SUPPORTS_ARBIT_HZ=y +CONFIG_SYS_SUPPORTS_HIGHMEM=y +CONFIG_SYS_SUPPORTS_HOTPLUG_CPU=y +CONFIG_SYS_SUPPORTS_LITTLE_ENDIAN=y +CONFIG_SYS_SUPPORTS_MIPS16=y +CONFIG_SYS_SUPPORTS_MIPS_CPS=y +CONFIG_SYS_SUPPORTS_MULTITHREADING=y +CONFIG_SYS_SUPPORTS_SCHED_SMT=y +CONFIG_SYS_SUPPORTS_SMP=y +CONFIG_TICK_CPU_ACCOUNTING=y +CONFIG_TIMER_OF=y +CONFIG_TIMER_PROBE=y +CONFIG_TREE_RCU=y +CONFIG_TREE_SRCU=y +CONFIG_UBIFS_FS=y +CONFIG_UBIFS_FS_ADVANCED_COMPR=y +CONFIG_UBIFS_FS_LZO=y +CONFIG_UBIFS_FS_ZLIB=y +CONFIG_USB_SUPPORT=y +CONFIG_USE_OF=y +CONFIG_WATCHDOG_CORE=y +CONFIG_WEAK_ORDERING=y +CONFIG_WEAK_REORDERING_BEYOND_LLSC=y +CONFIG_XPS=y +CONFIG_ZLIB_DEFLATE=y +CONFIG_ZLIB_INFLATE=y diff --git a/target/linux/ramips/patches-5.4/0001-MIPS-ralink-Add-rt3352-SPI_CS1-pinmux.patch b/target/linux/ramips/patches-5.4/0001-MIPS-ralink-Add-rt3352-SPI_CS1-pinmux.patch new file mode 100644 index 0000000000..4f803dfd0d --- /dev/null +++ b/target/linux/ramips/patches-5.4/0001-MIPS-ralink-Add-rt3352-SPI_CS1-pinmux.patch @@ -0,0 +1,45 @@ +From 35d017947401d9f449a7e55e52506744e0c62577 Mon Sep 17 00:00:00 2001 +From: Mathias Kresin +Date: Wed, 22 Aug 2018 22:38:06 +0200 +Subject: [PATCH] MIPS: ralink: Add rt3352 SPI_CS1 pinmux + +The rt3352 has a pin that can be used as second spi chip select, +watchdog reset or GPIO. The pinmux setup was missing the definition of +said pin. + +The pin is configured via the same bit on rt5350, so reuse the existing +macro. + +Signed-off-by: Mathias Kresin +Signed-off-by: Paul Burton +Patchwork: https://patchwork.linux-mips.org/patch/20301/ +Cc: John Crispin +Cc: Ralf Baechle +Cc: James Hogan +Cc: linux-mips@linux-mips.org +Cc: linux-kernel@vger.kernel.org +--- + arch/mips/ralink/rt305x.c | 5 +++++ + 1 file changed, 5 insertions(+) + +--- a/arch/mips/ralink/rt305x.c ++++ b/arch/mips/ralink/rt305x.c +@@ -49,6 +49,10 @@ static struct rt2880_pmx_func rgmii_func + static struct rt2880_pmx_func rt3352_lna_func[] = { FUNC("lna", 0, 36, 2) }; + static struct rt2880_pmx_func rt3352_pa_func[] = { FUNC("pa", 0, 38, 2) }; + static struct rt2880_pmx_func rt3352_led_func[] = { FUNC("led", 0, 40, 5) }; ++static struct rt2880_pmx_func rt3352_cs1_func[] = { ++ FUNC("spi_cs1", 0, 45, 1), ++ FUNC("wdg_cs1", 1, 45, 1), ++}; + + static struct rt2880_pmx_group rt3050_pinmux_data[] = { + GRP("i2c", i2c_func, 1, RT305X_GPIO_MODE_I2C), +@@ -75,6 +79,7 @@ static struct rt2880_pmx_group rt3352_pi + GRP("lna", rt3352_lna_func, 1, RT3352_GPIO_MODE_LNA), + GRP("pa", rt3352_pa_func, 1, RT3352_GPIO_MODE_PA), + GRP("led", rt3352_led_func, 1, RT5350_GPIO_MODE_PHY_LED), ++ GRP("spi_cs1", rt3352_cs1_func, 2, RT5350_GPIO_MODE_SPI_CS1), + { 0 } + }; + diff --git a/target/linux/ramips/patches-5.4/0002-MIPS-pci-rt2880-set-pci-controller-of_node.patch b/target/linux/ramips/patches-5.4/0002-MIPS-pci-rt2880-set-pci-controller-of_node.patch new file mode 100644 index 0000000000..7ac092cfb0 --- /dev/null +++ b/target/linux/ramips/patches-5.4/0002-MIPS-pci-rt2880-set-pci-controller-of_node.patch @@ -0,0 +1,32 @@ +From 0eb1cfffd5433d8dce3e4163a5cd9accc6000856 Mon Sep 17 00:00:00 2001 +From: Tobias Wolf +Date: Wed, 5 Sep 2018 08:51:26 +0200 +Subject: [PATCH] MIPS: pci-rt2880: set pci controller of_node + +Set the PCI controller of_node such that PCI devices can be +instantiated via device tree. + +Signed-off-by: Tobias Wolf +Signed-off-by: Mathias Kresin +Acked-by: John Crispin +Signed-off-by: Paul Burton +Patchwork: https://patchwork.linux-mips.org/patch/20423/ +Cc: Ralf Baechle +Cc: James Hogan +Cc: linux-mips@linux-mips.org +Cc: linux-kernel@vger.kernel.org +--- + arch/mips/pci/pci-rt2880.c | 2 ++ + 1 file changed, 2 insertions(+) + +--- a/arch/mips/pci/pci-rt2880.c ++++ b/arch/mips/pci/pci-rt2880.c +@@ -246,6 +246,8 @@ static int rt288x_pci_probe(struct platf + rt2880_pci_write_u32(PCI_BASE_ADDRESS_0, 0x08000000); + (void) rt2880_pci_read_u32(PCI_BASE_ADDRESS_0); + ++ rt2880_pci_controller.of_node = pdev->dev.of_node; ++ + register_pci_controller(&rt2880_pci_controller); + return 0; + } diff --git a/target/linux/ramips/patches-5.4/0003-MIPS-Fix-memory-reservation-in-bootmem_init-for-cert.patch b/target/linux/ramips/patches-5.4/0003-MIPS-Fix-memory-reservation-in-bootmem_init-for-cert.patch new file mode 100644 index 0000000000..77f2622b9d --- /dev/null +++ b/target/linux/ramips/patches-5.4/0003-MIPS-Fix-memory-reservation-in-bootmem_init-for-cert.patch @@ -0,0 +1,45 @@ +From: Tobias Wolf +Subject: [v2] MIPS: Fix memory reservation in bootmem_init for certain non-usermem setups + +Commit 67a3ba25aa95 ("MIPS: Fix incorrect mem=X@Y handling") introduced a new +issue for rt288x where "PHYS_OFFSET" is 0x0 but the calculated "ramstart" is +not. As the prerequisite of custom memory map has been removed, this results +in the full memory range of 0x0 - 0x8000000 to be marked as reserved for this +platform. + +v2: Correctly compare that usermem is not null. + +This patch adds the originally intended prerequisite again. + +Signed-off-by: Tobias Wolf +--- + +--- a/arch/mips/kernel/setup.c ++++ b/arch/mips/kernel/setup.c +@@ -369,6 +369,8 @@ static unsigned long __init bootmap_byte + return ALIGN(bytes, sizeof(long)); + } + ++static int usermem __initdata; ++ + static void __init bootmem_init(void) + { + unsigned long reserved_end; +@@ -442,7 +444,7 @@ static void __init bootmem_init(void) + /* + * Reserve any memory between the start of RAM and PHYS_OFFSET + */ +- if (ramstart > PHYS_OFFSET) ++ if (usermem && ramstart > PHYS_OFFSET) + add_memory_region(PHYS_OFFSET, ramstart - PHYS_OFFSET, + BOOT_MEM_RESERVED); + +@@ -652,8 +654,6 @@ static void __init bootmem_init(void) + * initialization hook for anything else was introduced. + */ + +-static int usermem __initdata; +- + static int __init early_parse_mem(char *p) + { + phys_addr_t start, size; diff --git a/target/linux/ramips/patches-5.4/0004-MIPS-ralink-add-MT7621-pcie-driver.patch b/target/linux/ramips/patches-5.4/0004-MIPS-ralink-add-MT7621-pcie-driver.patch new file mode 100644 index 0000000000..b6f1ce93f4 --- /dev/null +++ b/target/linux/ramips/patches-5.4/0004-MIPS-ralink-add-MT7621-pcie-driver.patch @@ -0,0 +1,861 @@ +From fec11d4e8dc5cc79bcd7c8fd55038ac21ac39965 Mon Sep 17 00:00:00 2001 +From: John Crispin +Date: Sun, 16 Mar 2014 05:22:39 +0000 +Subject: [PATCH 04/53] MIPS: ralink: add MT7621 pcie driver + +Signed-off-by: John Crispin +--- + arch/mips/pci/Makefile | 1 + + arch/mips/pci/pci-mt7621.c | 813 ++++++++++++++++++++++++++++++++++++++++++++ + 2 files changed, 814 insertions(+) + create mode 100644 arch/mips/pci/pci-mt7621.c + +--- a/arch/mips/pci/Makefile ++++ b/arch/mips/pci/Makefile +@@ -47,6 +47,7 @@ obj-$(CONFIG_SNI_RM) += fixup-sni.o ops + obj-$(CONFIG_LANTIQ) += fixup-lantiq.o + obj-$(CONFIG_PCI_LANTIQ) += pci-lantiq.o ops-lantiq.o + obj-$(CONFIG_SOC_MT7620) += pci-mt7620.o ++obj-$(CONFIG_SOC_MT7621) += pci-mt7621.o + obj-$(CONFIG_SOC_RT288X) += pci-rt2880.o + obj-$(CONFIG_SOC_RT3883) += pci-rt3883.o + obj-$(CONFIG_TANBAC_TB0219) += fixup-tb0219.o +--- /dev/null ++++ b/arch/mips/pci/pci-mt7621.c +@@ -0,0 +1,836 @@ ++/************************************************************************** ++ * ++ * BRIEF MODULE DESCRIPTION ++ * PCI init for Ralink RT2880 solution ++ * ++ * Copyright 2007 Ralink Inc. (bruce_chang@ralinktech.com.tw) ++ * ++ * This program is free software; you can redistribute it and/or modify it ++ * under the terms of the GNU General Public License as published by the ++ * Free Software Foundation; either version 2 of the License, or (at your ++ * option) any later version. ++ * ++ * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED ++ * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF ++ * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN ++ * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, ++ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT ++ * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF ++ * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ++ * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT ++ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF ++ * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. ++ * ++ * You should have received a copy of the GNU General Public License along ++ * with this program; if not, write to the Free Software Foundation, Inc., ++ * 675 Mass Ave, Cambridge, MA 02139, USA. ++ * ++ * ++ ************************************************************************** ++ * May 2007 Bruce Chang ++ * Initial Release ++ * ++ * May 2009 Bruce Chang ++ * support RT2880/RT3883 PCIe ++ * ++ * May 2011 Bruce Chang ++ * support RT6855/MT7620 PCIe ++ * ++ ************************************************************************** ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#include ++ ++extern void pcie_phy_init(void); ++extern void chk_phy_pll(void); ++ ++/* ++ * These functions and structures provide the BIOS scan and mapping of the PCI ++ * devices. ++ */ ++ ++#define CONFIG_PCIE_PORT0 ++#define CONFIG_PCIE_PORT1 ++#define CONFIG_PCIE_PORT2 ++#define RALINK_PCIE0_CLK_EN (1<<24) ++#define RALINK_PCIE1_CLK_EN (1<<25) ++#define RALINK_PCIE2_CLK_EN (1<<26) ++ ++#define RALINK_PCI_CONFIG_ADDR 0x20 ++#define RALINK_PCI_CONFIG_DATA_VIRTUAL_REG 0x24 ++#define RALINK_INT_PCIE0 pcie_irq[0] ++#define RALINK_INT_PCIE1 pcie_irq[1] ++#define RALINK_INT_PCIE2 pcie_irq[2] ++#define RALINK_PCI_MEMBASE *(volatile u32 *)(RALINK_PCI_BASE + 0x0028) ++#define RALINK_PCI_IOBASE *(volatile u32 *)(RALINK_PCI_BASE + 0x002C) ++#define RALINK_PCIE0_RST (1<<24) ++#define RALINK_PCIE1_RST (1<<25) ++#define RALINK_PCIE2_RST (1<<26) ++#define RALINK_SYSCTL_BASE 0xBE000000 ++ ++#define RALINK_PCI_PCICFG_ADDR *(volatile u32 *)(RALINK_PCI_BASE + 0x0000) ++#define RALINK_PCI_PCIMSK_ADDR *(volatile u32 *)(RALINK_PCI_BASE + 0x000C) ++#define RALINK_PCI_BASE 0xBE140000 ++ ++#define RALINK_PCIEPHY_P0P1_CTL_OFFSET (RALINK_PCI_BASE + 0x9000) ++#define RT6855_PCIE0_OFFSET 0x2000 ++#define RT6855_PCIE1_OFFSET 0x3000 ++#define RT6855_PCIE2_OFFSET 0x4000 ++ ++#define RALINK_PCI0_BAR0SETUP_ADDR *(volatile u32 *)(RALINK_PCI_BASE + RT6855_PCIE0_OFFSET + 0x0010) ++#define RALINK_PCI0_IMBASEBAR0_ADDR *(volatile u32 *)(RALINK_PCI_BASE + RT6855_PCIE0_OFFSET + 0x0018) ++#define RALINK_PCI0_ID *(volatile u32 *)(RALINK_PCI_BASE + RT6855_PCIE0_OFFSET + 0x0030) ++#define RALINK_PCI0_CLASS *(volatile u32 *)(RALINK_PCI_BASE + RT6855_PCIE0_OFFSET + 0x0034) ++#define RALINK_PCI0_SUBID *(volatile u32 *)(RALINK_PCI_BASE + RT6855_PCIE0_OFFSET + 0x0038) ++#define RALINK_PCI0_STATUS *(volatile u32 *)(RALINK_PCI_BASE + RT6855_PCIE0_OFFSET + 0x0050) ++#define RALINK_PCI0_DERR *(volatile u32 *)(RALINK_PCI_BASE + RT6855_PCIE0_OFFSET + 0x0060) ++#define RALINK_PCI0_ECRC *(volatile u32 *)(RALINK_PCI_BASE + RT6855_PCIE0_OFFSET + 0x0064) ++ ++#define RALINK_PCI1_BAR0SETUP_ADDR *(volatile u32 *)(RALINK_PCI_BASE + RT6855_PCIE1_OFFSET + 0x0010) ++#define RALINK_PCI1_IMBASEBAR0_ADDR *(volatile u32 *)(RALINK_PCI_BASE + RT6855_PCIE1_OFFSET + 0x0018) ++#define RALINK_PCI1_ID *(volatile u32 *)(RALINK_PCI_BASE + RT6855_PCIE1_OFFSET + 0x0030) ++#define RALINK_PCI1_CLASS *(volatile u32 *)(RALINK_PCI_BASE + RT6855_PCIE1_OFFSET + 0x0034) ++#define RALINK_PCI1_SUBID *(volatile u32 *)(RALINK_PCI_BASE + RT6855_PCIE1_OFFSET + 0x0038) ++#define RALINK_PCI1_STATUS *(volatile u32 *)(RALINK_PCI_BASE + RT6855_PCIE1_OFFSET + 0x0050) ++#define RALINK_PCI1_DERR *(volatile u32 *)(RALINK_PCI_BASE + RT6855_PCIE1_OFFSET + 0x0060) ++#define RALINK_PCI1_ECRC *(volatile u32 *)(RALINK_PCI_BASE + RT6855_PCIE1_OFFSET + 0x0064) ++ ++#define RALINK_PCI2_BAR0SETUP_ADDR *(volatile u32 *)(RALINK_PCI_BASE + RT6855_PCIE2_OFFSET + 0x0010) ++#define RALINK_PCI2_IMBASEBAR0_ADDR *(volatile u32 *)(RALINK_PCI_BASE + RT6855_PCIE2_OFFSET + 0x0018) ++#define RALINK_PCI2_ID *(volatile u32 *)(RALINK_PCI_BASE + RT6855_PCIE2_OFFSET + 0x0030) ++#define RALINK_PCI2_CLASS *(volatile u32 *)(RALINK_PCI_BASE + RT6855_PCIE2_OFFSET + 0x0034) ++#define RALINK_PCI2_SUBID *(volatile u32 *)(RALINK_PCI_BASE + RT6855_PCIE2_OFFSET + 0x0038) ++#define RALINK_PCI2_STATUS *(volatile u32 *)(RALINK_PCI_BASE + RT6855_PCIE2_OFFSET + 0x0050) ++#define RALINK_PCI2_DERR *(volatile u32 *)(RALINK_PCI_BASE + RT6855_PCIE2_OFFSET + 0x0060) ++#define RALINK_PCI2_ECRC *(volatile u32 *)(RALINK_PCI_BASE + RT6855_PCIE2_OFFSET + 0x0064) ++ ++#define RALINK_PCIEPHY_P0P1_CTL_OFFSET (RALINK_PCI_BASE + 0x9000) ++#define RALINK_PCIEPHY_P2_CTL_OFFSET (RALINK_PCI_BASE + 0xA000) ++ ++ ++#define MV_WRITE(ofs, data) \ ++ *(volatile u32 *)(RALINK_PCI_BASE+(ofs)) = cpu_to_le32(data) ++#define MV_READ(ofs, data) \ ++ *(data) = le32_to_cpu(*(volatile u32 *)(RALINK_PCI_BASE+(ofs))) ++#define MV_READ_DATA(ofs) \ ++ le32_to_cpu(*(volatile u32 *)(RALINK_PCI_BASE+(ofs))) ++ ++#define MV_WRITE_16(ofs, data) \ ++ *(volatile u16 *)(RALINK_PCI_BASE+(ofs)) = cpu_to_le16(data) ++#define MV_READ_16(ofs, data) \ ++ *(data) = le16_to_cpu(*(volatile u16 *)(RALINK_PCI_BASE+(ofs))) ++ ++#define MV_WRITE_8(ofs, data) \ ++ *(volatile u8 *)(RALINK_PCI_BASE+(ofs)) = data ++#define MV_READ_8(ofs, data) \ ++ *(data) = *(volatile u8 *)(RALINK_PCI_BASE+(ofs)) ++ ++ ++ ++#define RALINK_PCI_MM_MAP_BASE 0x60000000 ++#define RALINK_PCI_IO_MAP_BASE 0x1e160000 ++ ++#define RALINK_SYSTEM_CONTROL_BASE 0xbe000000 ++#define GPIO_PERST ++#define ASSERT_SYSRST_PCIE(val) do { \ ++ if (*(unsigned int *)(0xbe00000c) == 0x00030101) \ ++ RALINK_RSTCTRL |= val; \ ++ else \ ++ RALINK_RSTCTRL &= ~val; \ ++ } while(0) ++#define DEASSERT_SYSRST_PCIE(val) do { \ ++ if (*(unsigned int *)(0xbe00000c) == 0x00030101) \ ++ RALINK_RSTCTRL &= ~val; \ ++ else \ ++ RALINK_RSTCTRL |= val; \ ++ } while(0) ++#define RALINK_SYSCFG1 *(unsigned int *)(RALINK_SYSTEM_CONTROL_BASE + 0x14) ++#define RALINK_CLKCFG1 *(unsigned int *)(RALINK_SYSTEM_CONTROL_BASE + 0x30) ++#define RALINK_RSTCTRL *(unsigned int *)(RALINK_SYSTEM_CONTROL_BASE + 0x34) ++#define RALINK_GPIOMODE *(unsigned int *)(RALINK_SYSTEM_CONTROL_BASE + 0x60) ++#define RALINK_PCIE_CLK_GEN *(unsigned int *)(RALINK_SYSTEM_CONTROL_BASE + 0x7c) ++#define RALINK_PCIE_CLK_GEN1 *(unsigned int *)(RALINK_SYSTEM_CONTROL_BASE + 0x80) ++#define PPLL_CFG1 *(unsigned int *)(RALINK_SYSTEM_CONTROL_BASE + 0x9c) ++#define PPLL_DRV *(unsigned int *)(RALINK_SYSTEM_CONTROL_BASE + 0xa0) ++//RALINK_SYSCFG1 bit ++#define RALINK_PCI_HOST_MODE_EN (1<<7) ++#define RALINK_PCIE_RC_MODE_EN (1<<8) ++//RALINK_RSTCTRL bit ++#define RALINK_PCIE_RST (1<<23) ++#define RALINK_PCI_RST (1<<24) ++//RALINK_CLKCFG1 bit ++#define RALINK_PCI_CLK_EN (1<<19) ++#define RALINK_PCIE_CLK_EN (1<<21) ++//RALINK_GPIOMODE bit ++#define PCI_SLOTx2 (1<<11) ++#define PCI_SLOTx1 (2<<11) ++//MTK PCIE PLL bit ++#define PDRV_SW_SET (1<<31) ++#define LC_CKDRVPD_ (1<<19) ++ ++#define MEMORY_BASE 0x0 ++static int pcie_link_status = 0; ++ ++#define PCI_ACCESS_READ_1 0 ++#define PCI_ACCESS_READ_2 1 ++#define PCI_ACCESS_READ_4 2 ++#define PCI_ACCESS_WRITE_1 3 ++#define PCI_ACCESS_WRITE_2 4 ++#define PCI_ACCESS_WRITE_4 5 ++ ++static int pcie_irq[3]; ++ ++static int config_access(unsigned char access_type, struct pci_bus *bus, ++ unsigned int devfn, unsigned int where, u32 * data) ++{ ++ unsigned int slot = PCI_SLOT(devfn); ++ u8 func = PCI_FUNC(devfn); ++ uint32_t address_reg, data_reg; ++ unsigned int address; ++ ++ address_reg = RALINK_PCI_CONFIG_ADDR; ++ data_reg = RALINK_PCI_CONFIG_DATA_VIRTUAL_REG; ++ ++ address = (((where&0xF00)>>8)<<24) |(bus->number << 16) | (slot << 11) | (func << 8) | (where & 0xfc) | 0x80000000; ++ MV_WRITE(address_reg, address); ++ ++ switch(access_type) { ++ case PCI_ACCESS_WRITE_1: ++ MV_WRITE_8(data_reg+(where&0x3), *data); ++ break; ++ case PCI_ACCESS_WRITE_2: ++ MV_WRITE_16(data_reg+(where&0x3), *data); ++ break; ++ case PCI_ACCESS_WRITE_4: ++ MV_WRITE(data_reg, *data); ++ break; ++ case PCI_ACCESS_READ_1: ++ MV_READ_8( data_reg+(where&0x3), data); ++ break; ++ case PCI_ACCESS_READ_2: ++ MV_READ_16(data_reg+(where&0x3), data); ++ break; ++ case PCI_ACCESS_READ_4: ++ MV_READ(data_reg, data); ++ break; ++ default: ++ printk("no specify access type\n"); ++ break; ++ } ++ return 0; ++} ++ ++static int ++read_config_byte(struct pci_bus *bus, unsigned int devfn, int where, u8 * val) ++{ ++ return config_access(PCI_ACCESS_READ_1, bus, devfn, (unsigned int)where, (u32 *)val); ++} ++ ++static int ++read_config_word(struct pci_bus *bus, unsigned int devfn, int where, u16 * val) ++{ ++ return config_access(PCI_ACCESS_READ_2, bus, devfn, (unsigned int)where, (u32 *)val); ++} ++ ++static int ++read_config_dword(struct pci_bus *bus, unsigned int devfn, int where, u32 * val) ++{ ++ return config_access(PCI_ACCESS_READ_4, bus, devfn, (unsigned int)where, (u32 *)val); ++} ++ ++static int ++write_config_byte(struct pci_bus *bus, unsigned int devfn, int where, u8 val) ++{ ++ if (config_access(PCI_ACCESS_WRITE_1, bus, devfn, (unsigned int)where, (u32 *)&val)) ++ return -1; ++ ++ return PCIBIOS_SUCCESSFUL; ++} ++ ++static int ++write_config_word(struct pci_bus *bus, unsigned int devfn, int where, u16 val) ++{ ++ if (config_access(PCI_ACCESS_WRITE_2, bus, devfn, where, (u32 *)&val)) ++ return -1; ++ ++ return PCIBIOS_SUCCESSFUL; ++} ++ ++static int ++write_config_dword(struct pci_bus *bus, unsigned int devfn, int where, u32 val) ++{ ++ if (config_access(PCI_ACCESS_WRITE_4, bus, devfn, where, &val)) ++ return -1; ++ ++ return PCIBIOS_SUCCESSFUL; ++} ++ ++ ++static int ++pci_config_read(struct pci_bus *bus, unsigned int devfn, int where, int size, u32 * val) ++{ ++ switch (size) { ++ case 1: ++ return read_config_byte(bus, devfn, where, (u8 *) val); ++ case 2: ++ return read_config_word(bus, devfn, where, (u16 *) val); ++ default: ++ return read_config_dword(bus, devfn, where, val); ++ } ++} ++ ++static int ++pci_config_write(struct pci_bus *bus, unsigned int devfn, int where, int size, u32 val) ++{ ++ switch (size) { ++ case 1: ++ return write_config_byte(bus, devfn, where, (u8) val); ++ case 2: ++ return write_config_word(bus, devfn, where, (u16) val); ++ default: ++ return write_config_dword(bus, devfn, where, val); ++ } ++} ++ ++struct pci_ops mt7621_pci_ops= { ++ .read = pci_config_read, ++ .write = pci_config_write, ++}; ++ ++static struct resource mt7621_res_pci_mem1 = { ++ .name = "PCI MEM1", ++ .start = RALINK_PCI_MM_MAP_BASE, ++ .end = (u32)((RALINK_PCI_MM_MAP_BASE + (unsigned char *)0x0fffffff)), ++ .flags = IORESOURCE_MEM, ++}; ++static struct resource mt7621_res_pci_io1 = { ++ .name = "PCI I/O1", ++ .start = RALINK_PCI_IO_MAP_BASE, ++ .end = (u32)((RALINK_PCI_IO_MAP_BASE + (unsigned char *)0x0ffff)), ++ .flags = IORESOURCE_IO, ++}; ++ ++static struct pci_controller mt7621_controller = { ++ .pci_ops = &mt7621_pci_ops, ++ .mem_resource = &mt7621_res_pci_mem1, ++ .io_resource = &mt7621_res_pci_io1, ++ .mem_offset = 0x00000000UL, ++ .io_offset = 0x00000000UL, ++ .io_map_base = 0xa0000000, ++}; ++ ++static void ++read_config(unsigned long bus, unsigned long dev, unsigned long func, unsigned long reg, unsigned long *val) ++{ ++ unsigned int address_reg, data_reg, address; ++ ++ address_reg = RALINK_PCI_CONFIG_ADDR; ++ data_reg = RALINK_PCI_CONFIG_DATA_VIRTUAL_REG; ++ address = (((reg & 0xF00)>>8)<<24) | (bus << 16) | (dev << 11) | (func << 8) | (reg & 0xfc) | 0x80000000 ; ++ MV_WRITE(address_reg, address); ++ MV_READ(data_reg, val); ++ return; ++} ++ ++static void ++write_config(unsigned long bus, unsigned long dev, unsigned long func, unsigned long reg, unsigned long val) ++{ ++ unsigned int address_reg, data_reg, address; ++ ++ address_reg = RALINK_PCI_CONFIG_ADDR; ++ data_reg = RALINK_PCI_CONFIG_DATA_VIRTUAL_REG; ++ address = (((reg & 0xF00)>>8)<<24) | (bus << 16) | (dev << 11) | (func << 8) | (reg & 0xfc) | 0x80000000 ; ++ MV_WRITE(address_reg, address); ++ MV_WRITE(data_reg, val); ++ return; ++} ++ ++ ++int ++pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin) ++{ ++ u16 cmd; ++ u32 val; ++ int irq = 0; ++ ++ if ((dev->bus->number == 0) && (slot == 0)) { ++ write_config(0, 0, 0, PCI_BASE_ADDRESS_0, MEMORY_BASE); ++ read_config(0, 0, 0, PCI_BASE_ADDRESS_0, (unsigned long *)&val); ++ printk("BAR0 at slot 0 = %x\n", val); ++ printk("bus=0x%x, slot = 0x%x\n",dev->bus->number, slot); ++ } else if((dev->bus->number == 0) && (slot == 0x1)) { ++ write_config(0, 1, 0, PCI_BASE_ADDRESS_0, MEMORY_BASE); ++ read_config(0, 1, 0, PCI_BASE_ADDRESS_0, (unsigned long *)&val); ++ printk("BAR0 at slot 1 = %x\n", val); ++ printk("bus=0x%x, slot = 0x%x\n",dev->bus->number, slot); ++ } else if((dev->bus->number == 0) && (slot == 0x2)) { ++ write_config(0, 2, 0, PCI_BASE_ADDRESS_0, MEMORY_BASE); ++ read_config(0, 2, 0, PCI_BASE_ADDRESS_0, (unsigned long *)&val); ++ printk("BAR0 at slot 2 = %x\n", val); ++ printk("bus=0x%x, slot = 0x%x\n",dev->bus->number, slot); ++ } else if ((dev->bus->number == 1) && (slot == 0x0)) { ++ switch (pcie_link_status) { ++ case 2: ++ case 6: ++ irq = RALINK_INT_PCIE1; ++ break; ++ case 4: ++ irq = RALINK_INT_PCIE2; ++ break; ++ default: ++ irq = RALINK_INT_PCIE0; ++ } ++ printk("bus=0x%x, slot = 0x%x, irq=0x%x\n",dev->bus->number, slot, dev->irq); ++ } else if ((dev->bus->number == 2) && (slot == 0x0)) { ++ switch (pcie_link_status) { ++ case 5: ++ case 6: ++ irq = RALINK_INT_PCIE2; ++ break; ++ default: ++ irq = RALINK_INT_PCIE1; ++ } ++ printk("bus=0x%x, slot = 0x%x, irq=0x%x\n",dev->bus->number, slot, dev->irq); ++ } else if ((dev->bus->number == 2) && (slot == 0x1)) { ++ switch (pcie_link_status) { ++ case 5: ++ case 6: ++ irq = RALINK_INT_PCIE2; ++ break; ++ default: ++ irq = RALINK_INT_PCIE1; ++ } ++ printk("bus=0x%x, slot = 0x%x, irq=0x%x\n",dev->bus->number, slot, dev->irq); ++ } else if ((dev->bus->number ==3) && (slot == 0x0)) { ++ irq = RALINK_INT_PCIE2; ++ printk("bus=0x%x, slot = 0x%x, irq=0x%x\n",dev->bus->number, slot, dev->irq); ++ } else if ((dev->bus->number ==3) && (slot == 0x1)) { ++ irq = RALINK_INT_PCIE2; ++ printk("bus=0x%x, slot = 0x%x, irq=0x%x\n",dev->bus->number, slot, dev->irq); ++ } else if ((dev->bus->number ==3) && (slot == 0x2)) { ++ irq = RALINK_INT_PCIE2; ++ printk("bus=0x%x, slot = 0x%x, irq=0x%x\n",dev->bus->number, slot, dev->irq); ++ } else { ++ printk("bus=0x%x, slot = 0x%x\n",dev->bus->number, slot); ++ return 0; ++ } ++ ++ pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, 0x14); //configure cache line size 0x14 ++ pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0xFF); //configure latency timer 0x10 ++ pci_read_config_word(dev, PCI_COMMAND, &cmd); ++ cmd = cmd | PCI_COMMAND_MASTER | PCI_COMMAND_IO | PCI_COMMAND_MEMORY; ++ pci_write_config_word(dev, PCI_COMMAND, cmd); ++ pci_write_config_byte(dev, PCI_INTERRUPT_LINE, irq); ++ return irq; ++} ++ ++void ++set_pcie_phy(u32 *addr, int start_b, int bits, int val) ++{ ++// printk("0x%p:", addr); ++// printk(" %x", *addr); ++ *(unsigned int *)(addr) &= ~(((1< %x\n", *addr); ++} ++ ++void ++bypass_pipe_rst(void) ++{ ++#if defined (CONFIG_PCIE_PORT0) ++ /* PCIe Port 0 */ ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x02c), 12, 1, 0x01); // rg_pe1_pipe_rst_b ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x02c), 4, 1, 0x01); // rg_pe1_pipe_cmd_frc[4] ++#endif ++#if defined (CONFIG_PCIE_PORT1) ++ /* PCIe Port 1 */ ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x12c), 12, 1, 0x01); // rg_pe1_pipe_rst_b ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x12c), 4, 1, 0x01); // rg_pe1_pipe_cmd_frc[4] ++#endif ++#if defined (CONFIG_PCIE_PORT2) ++ /* PCIe Port 2 */ ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P2_CTL_OFFSET + 0x02c), 12, 1, 0x01); // rg_pe1_pipe_rst_b ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P2_CTL_OFFSET + 0x02c), 4, 1, 0x01); // rg_pe1_pipe_cmd_frc[4] ++#endif ++} ++ ++void ++set_phy_for_ssc(void) ++{ ++ unsigned long reg = (*(volatile u32 *)(RALINK_SYSCTL_BASE + 0x10)); ++ ++ reg = (reg >> 6) & 0x7; ++#if defined (CONFIG_PCIE_PORT0) || defined (CONFIG_PCIE_PORT1) ++ /* Set PCIe Port0 & Port1 PHY to disable SSC */ ++ /* Debug Xtal Type */ ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x400), 8, 1, 0x01); // rg_pe1_frc_h_xtal_type ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x400), 9, 2, 0x00); // rg_pe1_h_xtal_type ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x000), 4, 1, 0x01); // rg_pe1_frc_phy_en //Force Port 0 enable control ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x100), 4, 1, 0x01); // rg_pe1_frc_phy_en //Force Port 1 enable control ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x000), 5, 1, 0x00); // rg_pe1_phy_en //Port 0 disable ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x100), 5, 1, 0x00); // rg_pe1_phy_en //Port 1 disable ++ if(reg <= 5 && reg >= 3) { // 40MHz Xtal ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x490), 6, 2, 0x01); // RG_PE1_H_PLL_PREDIV //Pre-divider ratio (for host mode) ++ printk("***** Xtal 40MHz *****\n"); ++ } else { // 25MHz | 20MHz Xtal ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x490), 6, 2, 0x00); // RG_PE1_H_PLL_PREDIV //Pre-divider ratio (for host mode) ++ if (reg >= 6) { ++ printk("***** Xtal 25MHz *****\n"); ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x4bc), 4, 2, 0x01); // RG_PE1_H_PLL_FBKSEL //Feedback clock select ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x49c), 0,31, 0x18000000); // RG_PE1_H_LCDDS_PCW_NCPO //DDS NCPO PCW (for host mode) ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x4a4), 0,16, 0x18d); // RG_PE1_H_LCDDS_SSC_PRD //DDS SSC dither period control ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x4a8), 0,12, 0x4a); // RG_PE1_H_LCDDS_SSC_DELTA //DDS SSC dither amplitude control ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x4a8), 16,12, 0x4a); // RG_PE1_H_LCDDS_SSC_DELTA1 //DDS SSC dither amplitude control for initial ++ } else { ++ printk("***** Xtal 20MHz *****\n"); ++ } ++ } ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x4a0), 5, 1, 0x01); // RG_PE1_LCDDS_CLK_PH_INV //DDS clock inversion ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x490), 22, 2, 0x02); // RG_PE1_H_PLL_BC ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x490), 18, 4, 0x06); // RG_PE1_H_PLL_BP ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x490), 12, 4, 0x02); // RG_PE1_H_PLL_IR ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x490), 8, 4, 0x01); // RG_PE1_H_PLL_IC ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x4ac), 16, 3, 0x00); // RG_PE1_H_PLL_BR ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x490), 1, 3, 0x02); // RG_PE1_PLL_DIVEN ++ if(reg <= 5 && reg >= 3) { // 40MHz Xtal ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x414), 6, 2, 0x01); // rg_pe1_mstckdiv //value of da_pe1_mstckdiv when force mode enable ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x414), 5, 1, 0x01); // rg_pe1_frc_mstckdiv //force mode enable of da_pe1_mstckdiv ++ } ++ /* Enable PHY and disable force mode */ ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x000), 5, 1, 0x01); // rg_pe1_phy_en //Port 0 enable ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x100), 5, 1, 0x01); // rg_pe1_phy_en //Port 1 enable ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x000), 4, 1, 0x00); // rg_pe1_frc_phy_en //Force Port 0 disable control ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x100), 4, 1, 0x00); // rg_pe1_frc_phy_en //Force Port 1 disable control ++#endif ++#if defined (CONFIG_PCIE_PORT2) ++ /* Set PCIe Port2 PHY to disable SSC */ ++ /* Debug Xtal Type */ ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P2_CTL_OFFSET + 0x400), 8, 1, 0x01); // rg_pe1_frc_h_xtal_type ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P2_CTL_OFFSET + 0x400), 9, 2, 0x00); // rg_pe1_h_xtal_type ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P2_CTL_OFFSET + 0x000), 4, 1, 0x01); // rg_pe1_frc_phy_en //Force Port 0 enable control ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P2_CTL_OFFSET + 0x000), 5, 1, 0x00); // rg_pe1_phy_en //Port 0 disable ++ if(reg <= 5 && reg >= 3) { // 40MHz Xtal ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P2_CTL_OFFSET + 0x490), 6, 2, 0x01); // RG_PE1_H_PLL_PREDIV //Pre-divider ratio (for host mode) ++ } else { // 25MHz | 20MHz Xtal ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P2_CTL_OFFSET + 0x490), 6, 2, 0x00); // RG_PE1_H_PLL_PREDIV //Pre-divider ratio (for host mode) ++ if (reg >= 6) { // 25MHz Xtal ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P2_CTL_OFFSET + 0x4bc), 4, 2, 0x01); // RG_PE1_H_PLL_FBKSEL //Feedback clock select ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P2_CTL_OFFSET + 0x49c), 0,31, 0x18000000); // RG_PE1_H_LCDDS_PCW_NCPO //DDS NCPO PCW (for host mode) ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P2_CTL_OFFSET + 0x4a4), 0,16, 0x18d); // RG_PE1_H_LCDDS_SSC_PRD //DDS SSC dither period control ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P2_CTL_OFFSET + 0x4a8), 0,12, 0x4a); // RG_PE1_H_LCDDS_SSC_DELTA //DDS SSC dither amplitude control ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P2_CTL_OFFSET + 0x4a8), 16,12, 0x4a); // RG_PE1_H_LCDDS_SSC_DELTA1 //DDS SSC dither amplitude control for initial ++ } ++ } ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P2_CTL_OFFSET + 0x4a0), 5, 1, 0x01); // RG_PE1_LCDDS_CLK_PH_INV //DDS clock inversion ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P2_CTL_OFFSET + 0x490), 22, 2, 0x02); // RG_PE1_H_PLL_BC ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P2_CTL_OFFSET + 0x490), 18, 4, 0x06); // RG_PE1_H_PLL_BP ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P2_CTL_OFFSET + 0x490), 12, 4, 0x02); // RG_PE1_H_PLL_IR ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P2_CTL_OFFSET + 0x490), 8, 4, 0x01); // RG_PE1_H_PLL_IC ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P2_CTL_OFFSET + 0x4ac), 16, 3, 0x00); // RG_PE1_H_PLL_BR ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P2_CTL_OFFSET + 0x490), 1, 3, 0x02); // RG_PE1_PLL_DIVEN ++ if(reg <= 5 && reg >= 3) { // 40MHz Xtal ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P2_CTL_OFFSET + 0x414), 6, 2, 0x01); // rg_pe1_mstckdiv //value of da_pe1_mstckdiv when force mode enable ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P2_CTL_OFFSET + 0x414), 5, 1, 0x01); // rg_pe1_frc_mstckdiv //force mode enable of da_pe1_mstckdiv ++ } ++ /* Enable PHY and disable force mode */ ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P2_CTL_OFFSET + 0x000), 5, 1, 0x01); // rg_pe1_phy_en //Port 0 enable ++ set_pcie_phy((u32 *)(RALINK_PCIEPHY_P2_CTL_OFFSET + 0x000), 4, 1, 0x00); // rg_pe1_frc_phy_en //Force Port 0 disable control ++#endif ++} ++ ++void setup_cm_memory_region(struct resource *mem_resource) ++{ ++ resource_size_t mask; ++ if (mips_cps_numiocu(0)) { ++ /* FIXME: hardware doesn't accept mask values with 1s after ++ 0s (e.g. 0xffef), so it would be great to warn if that's ++ about to happen */ ++ mask = ~(mem_resource->end - mem_resource->start); ++ ++ write_gcr_reg1_base(mem_resource->start); ++ write_gcr_reg1_mask(mask | CM_GCR_REGn_MASK_CMTGT_IOCU0); ++ printk("PCI coherence region base: 0x%08lx, mask/settings: 0x%08lx\n", ++ read_gcr_reg1_base(), ++ read_gcr_reg1_mask()); ++ } ++} ++ ++static int mt7621_pci_probe(struct platform_device *pdev) ++{ ++ unsigned long val = 0; ++ int i; ++ ++ for (i = 0; i < 3; i++) ++ pcie_irq[i] = irq_of_parse_and_map(pdev->dev.of_node, i); ++ ++ iomem_resource.start = 0; ++ iomem_resource.end= ~0; ++ ioport_resource.start= 0; ++ ioport_resource.end = ~0; ++ ++#if defined (CONFIG_PCIE_PORT0) ++ val = RALINK_PCIE0_RST; ++#endif ++#if defined (CONFIG_PCIE_PORT1) ++ val |= RALINK_PCIE1_RST; ++#endif ++#if defined (CONFIG_PCIE_PORT2) ++ val |= RALINK_PCIE2_RST; ++#endif ++ ASSERT_SYSRST_PCIE(RALINK_PCIE0_RST | RALINK_PCIE1_RST | RALINK_PCIE2_RST); ++ printk("pull PCIe RST: RALINK_RSTCTRL = %x\n", RALINK_RSTCTRL); ++#if defined GPIO_PERST /* add GPIO control instead of PERST_N */ /*chhung*/ ++ *(unsigned int *)(0xbe000060) &= ~(0x3<<10 | 0x3<<3); ++ *(unsigned int *)(0xbe000060) |= 0x1<<10 | 0x1<<3; ++ mdelay(100); ++ *(unsigned int *)(0xbe000600) |= 0x1<<19 | 0x1<<8 | 0x1<<7; // use GPIO19/GPIO8/GPIO7 (PERST_N/UART_RXD3/UART_TXD3) ++ mdelay(100); ++ *(unsigned int *)(0xbe000620) &= ~(0x1<<19 | 0x1<<8 | 0x1<<7); // clear DATA ++ ++ mdelay(100); ++#else ++ *(unsigned int *)(0xbe000060) &= ~0x00000c00; ++#endif ++#if defined (CONFIG_PCIE_PORT0) ++ val = RALINK_PCIE0_RST; ++#endif ++#if defined (CONFIG_PCIE_PORT1) ++ val |= RALINK_PCIE1_RST; ++#endif ++#if defined (CONFIG_PCIE_PORT2) ++ val |= RALINK_PCIE2_RST; ++#endif ++ DEASSERT_SYSRST_PCIE(val); ++ printk("release PCIe RST: RALINK_RSTCTRL = %x\n", RALINK_RSTCTRL); ++ ++ if ((*(unsigned int *)(0xbe00000c)&0xFFFF) == 0x0101) // MT7621 E2 ++ bypass_pipe_rst(); ++ set_phy_for_ssc(); ++ printk("release PCIe RST: RALINK_RSTCTRL = %x\n", RALINK_RSTCTRL); ++ ++#if defined (CONFIG_PCIE_PORT0) ++ read_config(0, 0, 0, 0x70c, &val); ++ printk("Port 0 N_FTS = %x\n", (unsigned int)val); ++#endif ++#if defined (CONFIG_PCIE_PORT1) ++ read_config(0, 1, 0, 0x70c, &val); ++ printk("Port 1 N_FTS = %x\n", (unsigned int)val); ++#endif ++#if defined (CONFIG_PCIE_PORT2) ++ read_config(0, 2, 0, 0x70c, &val); ++ printk("Port 2 N_FTS = %x\n", (unsigned int)val); ++#endif ++ ++ RALINK_RSTCTRL = (RALINK_RSTCTRL | RALINK_PCIE_RST); ++ RALINK_SYSCFG1 &= ~(0x30); ++ RALINK_SYSCFG1 |= (2<<4); ++ RALINK_PCIE_CLK_GEN &= 0x7fffffff; ++ RALINK_PCIE_CLK_GEN1 &= 0x80ffffff; ++ RALINK_PCIE_CLK_GEN1 |= 0xa << 24; ++ RALINK_PCIE_CLK_GEN |= 0x80000000; ++ mdelay(50); ++ RALINK_RSTCTRL = (RALINK_RSTCTRL & ~RALINK_PCIE_RST); ++ ++ ++#if defined GPIO_PERST /* add GPIO control instead of PERST_N */ /*chhung*/ ++ *(unsigned int *)(0xbe000620) |= 0x1<<19 | 0x1<<8 | 0x1<<7; // set DATA ++ mdelay(100); ++#else ++ RALINK_PCI_PCICFG_ADDR &= ~(1<<1); //de-assert PERST ++#endif ++ mdelay(500); ++ ++ ++ mdelay(500); ++#if defined (CONFIG_PCIE_PORT0) ++ if(( RALINK_PCI0_STATUS & 0x1) == 0) ++ { ++ printk("PCIE0 no card, disable it(RST&CLK)\n"); ++ ASSERT_SYSRST_PCIE(RALINK_PCIE0_RST); ++ RALINK_CLKCFG1 = (RALINK_CLKCFG1 & ~RALINK_PCIE0_CLK_EN); ++ pcie_link_status &= ~(1<<0); ++ } else { ++ pcie_link_status |= 1<<0; ++ RALINK_PCI_PCIMSK_ADDR |= (1<<20); // enable pcie1 interrupt ++ } ++#endif ++#if defined (CONFIG_PCIE_PORT1) ++ if(( RALINK_PCI1_STATUS & 0x1) == 0) ++ { ++ printk("PCIE1 no card, disable it(RST&CLK)\n"); ++ ASSERT_SYSRST_PCIE(RALINK_PCIE1_RST); ++ RALINK_CLKCFG1 = (RALINK_CLKCFG1 & ~RALINK_PCIE1_CLK_EN); ++ pcie_link_status &= ~(1<<1); ++ } else { ++ pcie_link_status |= 1<<1; ++ RALINK_PCI_PCIMSK_ADDR |= (1<<21); // enable pcie1 interrupt ++ } ++#endif ++#if defined (CONFIG_PCIE_PORT2) ++ if (( RALINK_PCI2_STATUS & 0x1) == 0) { ++ printk("PCIE2 no card, disable it(RST&CLK)\n"); ++ ASSERT_SYSRST_PCIE(RALINK_PCIE2_RST); ++ RALINK_CLKCFG1 = (RALINK_CLKCFG1 & ~RALINK_PCIE2_CLK_EN); ++ pcie_link_status &= ~(1<<2); ++ } else { ++ pcie_link_status |= 1<<2; ++ RALINK_PCI_PCIMSK_ADDR |= (1<<22); // enable pcie2 interrupt ++ } ++#endif ++ if (pcie_link_status == 0) ++ return 0; ++ ++/* ++pcie(2/1/0) link status pcie2_num pcie1_num pcie0_num ++3'b000 x x x ++3'b001 x x 0 ++3'b010 x 0 x ++3'b011 x 1 0 ++3'b100 0 x x ++3'b101 1 x 0 ++3'b110 1 0 x ++3'b111 2 1 0 ++*/ ++ switch(pcie_link_status) { ++ case 2: ++ RALINK_PCI_PCICFG_ADDR &= ~0x00ff0000; ++ RALINK_PCI_PCICFG_ADDR |= 0x1 << 16; //port0 ++ RALINK_PCI_PCICFG_ADDR |= 0x0 << 20; //port1 ++ break; ++ case 4: ++ RALINK_PCI_PCICFG_ADDR &= ~0x0fff0000; ++ RALINK_PCI_PCICFG_ADDR |= 0x1 << 16; //port0 ++ RALINK_PCI_PCICFG_ADDR |= 0x2 << 20; //port1 ++ RALINK_PCI_PCICFG_ADDR |= 0x0 << 24; //port2 ++ break; ++ case 5: ++ RALINK_PCI_PCICFG_ADDR &= ~0x0fff0000; ++ RALINK_PCI_PCICFG_ADDR |= 0x0 << 16; //port0 ++ RALINK_PCI_PCICFG_ADDR |= 0x2 << 20; //port1 ++ RALINK_PCI_PCICFG_ADDR |= 0x1 << 24; //port2 ++ break; ++ case 6: ++ RALINK_PCI_PCICFG_ADDR &= ~0x0fff0000; ++ RALINK_PCI_PCICFG_ADDR |= 0x2 << 16; //port0 ++ RALINK_PCI_PCICFG_ADDR |= 0x0 << 20; //port1 ++ RALINK_PCI_PCICFG_ADDR |= 0x1 << 24; //port2 ++ break; ++ } ++ printk(" -> %x\n", RALINK_PCI_PCICFG_ADDR); ++ //printk(" RALINK_PCI_ARBCTL = %x\n", RALINK_PCI_ARBCTL); ++ ++/* ++ ioport_resource.start = mt7621_res_pci_io1.start; ++ ioport_resource.end = mt7621_res_pci_io1.end; ++*/ ++ ++ RALINK_PCI_MEMBASE = 0xffffffff; //RALINK_PCI_MM_MAP_BASE; ++ RALINK_PCI_IOBASE = RALINK_PCI_IO_MAP_BASE; ++ ++#if defined (CONFIG_PCIE_PORT0) ++ //PCIe0 ++ if((pcie_link_status & 0x1) != 0) { ++ RALINK_PCI0_BAR0SETUP_ADDR = 0x7FFF0001; //open 7FFF:2G; ENABLE ++ RALINK_PCI0_IMBASEBAR0_ADDR = MEMORY_BASE; ++ RALINK_PCI0_CLASS = 0x06040001; ++ printk("PCIE0 enabled\n"); ++ } ++#endif ++#if defined (CONFIG_PCIE_PORT1) ++ //PCIe1 ++ if ((pcie_link_status & 0x2) != 0) { ++ RALINK_PCI1_BAR0SETUP_ADDR = 0x7FFF0001; //open 7FFF:2G; ENABLE ++ RALINK_PCI1_IMBASEBAR0_ADDR = MEMORY_BASE; ++ RALINK_PCI1_CLASS = 0x06040001; ++ printk("PCIE1 enabled\n"); ++ } ++#endif ++#if defined (CONFIG_PCIE_PORT2) ++ //PCIe2 ++ if ((pcie_link_status & 0x4) != 0) { ++ RALINK_PCI2_BAR0SETUP_ADDR = 0x7FFF0001; //open 7FFF:2G; ENABLE ++ RALINK_PCI2_IMBASEBAR0_ADDR = MEMORY_BASE; ++ RALINK_PCI2_CLASS = 0x06040001; ++ printk("PCIE2 enabled\n"); ++ } ++#endif ++ ++ ++ switch(pcie_link_status) { ++ case 7: ++ read_config(0, 2, 0, 0x4, &val); ++ write_config(0, 2, 0, 0x4, val|0x4); ++ // write_config(0, 1, 0, 0x4, val|0x7); ++ read_config(0, 2, 0, 0x70c, &val); ++ val &= ~(0xff)<<8; ++ val |= 0x50<<8; ++ write_config(0, 2, 0, 0x70c, val); ++ case 3: ++ case 5: ++ case 6: ++ read_config(0, 1, 0, 0x4, &val); ++ write_config(0, 1, 0, 0x4, val|0x4); ++ // write_config(0, 1, 0, 0x4, val|0x7); ++ read_config(0, 1, 0, 0x70c, &val); ++ val &= ~(0xff)<<8; ++ val |= 0x50<<8; ++ write_config(0, 1, 0, 0x70c, val); ++ default: ++ read_config(0, 0, 0, 0x4, &val); ++ write_config(0, 0, 0, 0x4, val|0x4); //bus master enable ++ // write_config(0, 0, 0, 0x4, val|0x7); //bus master enable ++ read_config(0, 0, 0, 0x70c, &val); ++ val &= ~(0xff)<<8; ++ val |= 0x50<<8; ++ write_config(0, 0, 0, 0x70c, val); ++ } ++ ++ pci_load_of_ranges(&mt7621_controller, pdev->dev.of_node); ++ setup_cm_memory_region(mt7621_controller.mem_resource); ++ register_pci_controller(&mt7621_controller); ++ return 0; ++ ++} ++ ++int pcibios_plat_dev_init(struct pci_dev *dev) ++{ ++ return 0; ++} ++ ++static const struct of_device_id mt7621_pci_ids[] = { ++ { .compatible = "mediatek,mt7621-pci" }, ++ {}, ++}; ++MODULE_DEVICE_TABLE(of, mt7621_pci_ids); ++ ++static struct platform_driver mt7621_pci_driver = { ++ .probe = mt7621_pci_probe, ++ .driver = { ++ .name = "mt7621-pci", ++ .owner = THIS_MODULE, ++ .of_match_table = of_match_ptr(mt7621_pci_ids), ++ }, ++}; ++ ++static int __init mt7621_pci_init(void) ++{ ++ return platform_driver_register(&mt7621_pci_driver); ++} ++ ++arch_initcall(mt7621_pci_init); diff --git a/target/linux/ramips/patches-5.4/0005-MIPS-use-set_mode-to-enable-disable-the-cevt-r4k-irq.patch b/target/linux/ramips/patches-5.4/0005-MIPS-use-set_mode-to-enable-disable-the-cevt-r4k-irq.patch new file mode 100644 index 0000000000..773c74f4e9 --- /dev/null +++ b/target/linux/ramips/patches-5.4/0005-MIPS-use-set_mode-to-enable-disable-the-cevt-r4k-irq.patch @@ -0,0 +1,82 @@ +From ce3d4a4111a5f7e6b4e74bceae5faa6ce388e8ec Mon Sep 17 00:00:00 2001 +From: John Crispin +Date: Sun, 14 Jul 2013 23:08:11 +0200 +Subject: [PATCH 05/53] MIPS: use set_mode() to enable/disable the cevt-r4k + irq + +Signed-off-by: John Crispin +--- + arch/mips/ralink/Kconfig | 5 +++++ + 1 file changed, 5 insertions(+) + +--- a/arch/mips/ralink/Kconfig ++++ b/arch/mips/ralink/Kconfig +@@ -1,12 +1,17 @@ + # SPDX-License-Identifier: GPL-2.0 + if RALINK + ++config CEVT_SYSTICK_QUIRK ++ bool ++ default n ++ + config CLKEVT_RT3352 + bool + depends on SOC_RT305X || SOC_MT7620 + default y + select TIMER_OF + select CLKSRC_MMIO ++ select CEVT_SYSTICK_QUIRK + + config RALINK_ILL_ACC + bool +--- a/arch/mips/kernel/cevt-r4k.c ++++ b/arch/mips/kernel/cevt-r4k.c +@@ -15,6 +15,26 @@ + #include + #include + ++static int mips_state_oneshot(struct clock_event_device *evt) ++{ ++ if (!cp0_timer_irq_installed) { ++ cp0_timer_irq_installed = 1; ++ setup_irq(evt->irq, &c0_compare_irqaction); ++ } ++ ++ return 0; ++} ++ ++static int mips_state_shutdown(struct clock_event_device *evt) ++{ ++ if (cp0_timer_irq_installed) { ++ cp0_timer_irq_installed = 0; ++ remove_irq(evt->irq, &c0_compare_irqaction); ++ } ++ ++ return 0; ++} ++ + static int mips_next_event(unsigned long delta, + struct clock_event_device *evt) + { +@@ -281,17 +301,21 @@ int r4k_clockevent_init(void) + cd->rating = 300; + cd->irq = irq; + cd->cpumask = cpumask_of(cpu); ++ cd->set_state_shutdown = mips_state_shutdown; ++ cd->set_state_oneshot = mips_state_oneshot; + cd->set_next_event = mips_next_event; + cd->event_handler = mips_event_handler; + + clockevents_config_and_register(cd, mips_hpt_frequency, min_delta, 0x7fffffff); + ++#ifndef CONFIG_CEVT_SYSTICK_QUIRK + if (cp0_timer_irq_installed) + return 0; + + cp0_timer_irq_installed = 1; + + setup_irq(irq, &c0_compare_irqaction); ++#endif + + return 0; + } diff --git a/target/linux/ramips/patches-5.4/0006-MIPS-ralink-add-cpu-frequency-scaling.patch b/target/linux/ramips/patches-5.4/0006-MIPS-ralink-add-cpu-frequency-scaling.patch new file mode 100644 index 0000000000..90215fbf86 --- /dev/null +++ b/target/linux/ramips/patches-5.4/0006-MIPS-ralink-add-cpu-frequency-scaling.patch @@ -0,0 +1,200 @@ +From bd30f19a006fb52bac80c6463c49dd2f4159f4ac Mon Sep 17 00:00:00 2001 +From: John Crispin +Date: Sun, 28 Jul 2013 16:26:41 +0200 +Subject: [PATCH 06/53] MIPS: ralink: add cpu frequency scaling + +This feature will break udelay() and cause the delay loop to have longer delays +when the frequency is scaled causing a performance hit. + +Signed-off-by: John Crispin +--- + arch/mips/ralink/cevt-rt3352.c | 38 ++++++++++++++++++++++++++++++++++++++ + 1 file changed, 38 insertions(+) + +--- a/arch/mips/ralink/cevt-rt3352.c ++++ b/arch/mips/ralink/cevt-rt3352.c +@@ -29,6 +29,10 @@ + /* enable the counter */ + #define CFG_CNT_EN 0x1 + ++/* mt7620 frequency scaling defines */ ++#define CLK_LUT_CFG 0x40 ++#define SLEEP_EN BIT(31) ++ + struct systick_device { + void __iomem *membase; + struct clock_event_device dev; +@@ -36,21 +40,53 @@ struct systick_device { + int freq_scale; + }; + ++static void (*systick_freq_scaling)(struct systick_device *sdev, int status); ++ + static int systick_set_oneshot(struct clock_event_device *evt); + static int systick_shutdown(struct clock_event_device *evt); + ++static inline void mt7620_freq_scaling(struct systick_device *sdev, int status) ++{ ++ if (sdev->freq_scale == status) ++ return; ++ ++ sdev->freq_scale = status; ++ ++ pr_info("%s: %s autosleep mode\n", sdev->dev.name, ++ (status) ? ("enable") : ("disable")); ++ if (status) ++ rt_sysc_w32(rt_sysc_r32(CLK_LUT_CFG) | SLEEP_EN, CLK_LUT_CFG); ++ else ++ rt_sysc_w32(rt_sysc_r32(CLK_LUT_CFG) & ~SLEEP_EN, CLK_LUT_CFG); ++} ++ ++static inline unsigned int read_count(struct systick_device *sdev) ++{ ++ return ioread32(sdev->membase + SYSTICK_COUNT); ++} ++ ++static inline unsigned int read_compare(struct systick_device *sdev) ++{ ++ return ioread32(sdev->membase + SYSTICK_COMPARE); ++} ++ ++static inline void write_compare(struct systick_device *sdev, unsigned int val) ++{ ++ iowrite32(val, sdev->membase + SYSTICK_COMPARE); ++} ++ + static int systick_next_event(unsigned long delta, + struct clock_event_device *evt) + { + struct systick_device *sdev; +- u32 count; ++ int res; + + sdev = container_of(evt, struct systick_device, dev); +- count = ioread32(sdev->membase + SYSTICK_COUNT); +- count = (count + delta) % SYSTICK_FREQ; +- iowrite32(count, sdev->membase + SYSTICK_COMPARE); ++ delta += read_count(sdev); ++ write_compare(sdev, delta); ++ res = ((int)(read_count(sdev) - delta) >= 0) ? -ETIME : 0; + +- return 0; ++ return res; + } + + static void systick_event_handler(struct clock_event_device *dev) +@@ -60,20 +96,25 @@ static void systick_event_handler(struct + + static irqreturn_t systick_interrupt(int irq, void *dev_id) + { +- struct clock_event_device *dev = (struct clock_event_device *) dev_id; ++ int ret = 0; ++ struct clock_event_device *cdev; ++ struct systick_device *sdev; + +- dev->event_handler(dev); ++ if (read_c0_cause() & STATUSF_IP7) { ++ cdev = (struct clock_event_device *) dev_id; ++ sdev = container_of(cdev, struct systick_device, dev); ++ ++ /* Clear Count/Compare Interrupt */ ++ write_compare(sdev, read_compare(sdev)); ++ cdev->event_handler(cdev); ++ ret = 1; ++ } + +- return IRQ_HANDLED; ++ return IRQ_RETVAL(ret); + } + + static struct systick_device systick = { + .dev = { +- /* +- * cevt-r4k uses 300, make sure systick +- * gets used if available +- */ +- .rating = 310, + .features = CLOCK_EVT_FEAT_ONESHOT, + .set_next_event = systick_next_event, + .set_state_shutdown = systick_shutdown, +@@ -95,9 +136,15 @@ static int systick_shutdown(struct clock + sdev = container_of(evt, struct systick_device, dev); + + if (sdev->irq_requested) +- free_irq(systick.dev.irq, &systick_irqaction); ++ remove_irq(systick.dev.irq, &systick_irqaction); + sdev->irq_requested = 0; +- iowrite32(0, systick.membase + SYSTICK_CONFIG); ++ iowrite32(CFG_CNT_EN, systick.membase + SYSTICK_CONFIG); ++ ++ if (systick_freq_scaling) ++ systick_freq_scaling(sdev, 0); ++ ++ if (systick_freq_scaling) ++ systick_freq_scaling(sdev, 1); + + return 0; + } +@@ -117,34 +164,48 @@ static int systick_set_oneshot(struct cl + return 0; + } + ++static const struct of_device_id systick_match[] = { ++ { .compatible = "ralink,mt7620a-systick", .data = mt7620_freq_scaling}, ++ {}, ++}; ++ + static int __init ralink_systick_init(struct device_node *np) + { ++ const struct of_device_id *match; ++ int rating = 200; + int ret; + + systick.membase = of_iomap(np, 0); + if (!systick.membase) + return -ENXIO; + +- systick_irqaction.name = np->name; +- systick.dev.name = np->name; +- clockevents_calc_mult_shift(&systick.dev, SYSTICK_FREQ, 60); +- systick.dev.max_delta_ns = clockevent_delta2ns(0x7fff, &systick.dev); +- systick.dev.max_delta_ticks = 0x7fff; +- systick.dev.min_delta_ns = clockevent_delta2ns(0x3, &systick.dev); +- systick.dev.min_delta_ticks = 0x3; ++ match = of_match_node(systick_match, np); ++ if (match) { ++ systick_freq_scaling = match->data; ++ /* ++ * cevt-r4k uses 300, make sure systick ++ * gets used if available ++ */ ++ rating = 310; ++ } ++ ++ /* enable counter than register clock source */ ++ iowrite32(CFG_CNT_EN, systick.membase + SYSTICK_CONFIG); ++ clocksource_mmio_init(systick.membase + SYSTICK_COUNT, np->name, ++ SYSTICK_FREQ, rating, 16, clocksource_mmio_readl_up); ++ ++ /* register clock event */ + systick.dev.irq = irq_of_parse_and_map(np, 0); + if (!systick.dev.irq) { + pr_err("%s: request_irq failed", np->name); + return -EINVAL; + } + +- ret = clocksource_mmio_init(systick.membase + SYSTICK_COUNT, np->name, +- SYSTICK_FREQ, 301, 16, +- clocksource_mmio_readl_up); +- if (ret) +- return ret; +- +- clockevents_register_device(&systick.dev); ++ systick_irqaction.name = np->name; ++ systick.dev.name = np->name; ++ systick.dev.rating = rating; ++ systick.dev.cpumask = cpumask_of(0); ++ clockevents_config_and_register(&systick.dev, SYSTICK_FREQ, 0x3, 0x7fff); + + pr_info("%s: running - mult: %d, shift: %d\n", + np->name, systick.dev.mult, systick.dev.shift); diff --git a/target/linux/ramips/patches-5.4/0007-MIPS-ralink-copy-the-commandline-from-the-devicetree.patch b/target/linux/ramips/patches-5.4/0007-MIPS-ralink-copy-the-commandline-from-the-devicetree.patch new file mode 100644 index 0000000000..c05ee8018d --- /dev/null +++ b/target/linux/ramips/patches-5.4/0007-MIPS-ralink-copy-the-commandline-from-the-devicetree.patch @@ -0,0 +1,21 @@ +From 67b7bff0fd364c194e653f69baa623ba2141bd4c Mon Sep 17 00:00:00 2001 +From: John Crispin +Date: Mon, 4 Aug 2014 18:46:02 +0200 +Subject: [PATCH 07/53] MIPS: ralink: copy the commandline from the devicetree + +Signed-off-by: John Crispin +--- + arch/mips/ralink/of.c | 2 ++ + 1 file changed, 2 insertions(+) + +--- a/arch/mips/ralink/of.c ++++ b/arch/mips/ralink/of.c +@@ -82,6 +82,8 @@ void __init plat_mem_setup(void) + + __dt_setup_arch(dtb); + ++ strlcpy(arcs_cmdline, boot_command_line, COMMAND_LINE_SIZE); ++ + of_scan_flat_dt(early_init_dt_find_memory, NULL); + if (memory_dtb) + of_scan_flat_dt(early_init_dt_scan_memory, NULL); diff --git a/target/linux/ramips/patches-5.4/0009-PCI-MIPS-enable-PCIe-on-MT7688.patch b/target/linux/ramips/patches-5.4/0009-PCI-MIPS-enable-PCIe-on-MT7688.patch new file mode 100644 index 0000000000..6ca15fe32e --- /dev/null +++ b/target/linux/ramips/patches-5.4/0009-PCI-MIPS-enable-PCIe-on-MT7688.patch @@ -0,0 +1,28 @@ +From 7768798964eb0e4f95eaecffb93b5d0ca28a38af Mon Sep 17 00:00:00 2001 +From: Daniel Golle +Date: Sat, 3 Jun 2017 20:00:03 +0200 +Subject: [PATCH] MIPS: pci-mt7620: enabled PCIe on MT7688 +To: linux-mips@linux-mips.org, + John Crispin +Cc: Wei Yongjun , + Ralf Baechle , + linux-mediatek@lists.infradead.org + +Use PCIe support for MT7628AN also on MT7688. +Tested on WRTNODE2R. + +Signed-off-by: Daniel Golle +--- + arch/mips/pci/pci-mt7620.c | 1 + + 1 file changed, 1 insertion(+) + +--- a/arch/mips/pci/pci-mt7620.c ++++ b/arch/mips/pci/pci-mt7620.c +@@ -316,6 +316,7 @@ static int mt7620_pci_probe(struct platf + break; + + case MT762X_SOC_MT7628AN: ++ case MT762X_SOC_MT7688: + if (mt7628_pci_hw_init(pdev)) + return -1; + break; diff --git a/target/linux/ramips/patches-5.4/0013-owrt-hack-fix-mt7688-cache-issue.patch b/target/linux/ramips/patches-5.4/0013-owrt-hack-fix-mt7688-cache-issue.patch new file mode 100644 index 0000000000..442f3180a3 --- /dev/null +++ b/target/linux/ramips/patches-5.4/0013-owrt-hack-fix-mt7688-cache-issue.patch @@ -0,0 +1,28 @@ +From 5ede027f6c4a57ed25da872420508b7f1168b36b Mon Sep 17 00:00:00 2001 +From: John Crispin +Date: Mon, 7 Dec 2015 17:15:32 +0100 +Subject: [PATCH 13/53] owrt: hack: fix mt7688 cache issue + +Signed-off-by: John Crispin +--- + arch/mips/kernel/setup.c | 2 +- + 1 file changed, 1 insertion(+), 1 deletion(-) + +--- a/arch/mips/kernel/setup.c ++++ b/arch/mips/kernel/setup.c +@@ -910,7 +910,6 @@ static void __init arch_mem_init(char ** + crashk_res.end - crashk_res.start + 1, + BOOTMEM_DEFAULT); + #endif +- device_tree_init(); + sparse_init(); + plat_swiotlb_setup(); + +@@ -1026,6 +1025,7 @@ void __init setup_arch(char **cmdline_p) + + cpu_cache_init(); + paging_init(); ++ device_tree_init(); + } + + unsigned long kernelsp[NR_CPUS]; diff --git a/target/linux/ramips/patches-5.4/0015-arch-mips-do-not-select-illegal-access-driver-by-def.patch b/target/linux/ramips/patches-5.4/0015-arch-mips-do-not-select-illegal-access-driver-by-def.patch new file mode 100644 index 0000000000..1dc54ccf23 --- /dev/null +++ b/target/linux/ramips/patches-5.4/0015-arch-mips-do-not-select-illegal-access-driver-by-def.patch @@ -0,0 +1,25 @@ +From 9e6ce539092a1dd605a20bf73c655a9de58d8641 Mon Sep 17 00:00:00 2001 +From: John Crispin +Date: Mon, 7 Dec 2015 17:18:05 +0100 +Subject: [PATCH 15/53] arch: mips: do not select illegal access driver by + default + +Signed-off-by: John Crispin +--- + arch/mips/ralink/Kconfig | 4 ++-- + 1 file changed, 2 insertions(+), 2 deletions(-) + +--- a/arch/mips/ralink/Kconfig ++++ b/arch/mips/ralink/Kconfig +@@ -14,9 +14,9 @@ config CLKEVT_RT3352 + select CEVT_SYSTICK_QUIRK + + config RALINK_ILL_ACC +- bool ++ bool "illegal access irq" + depends on SOC_RT305X +- default y ++ default n + + config IRQ_INTC + bool diff --git a/target/linux/ramips/patches-5.4/0024-GPIO-add-named-gpio-exports.patch b/target/linux/ramips/patches-5.4/0024-GPIO-add-named-gpio-exports.patch new file mode 100644 index 0000000000..61ed9ea784 --- /dev/null +++ b/target/linux/ramips/patches-5.4/0024-GPIO-add-named-gpio-exports.patch @@ -0,0 +1,165 @@ +From 4267880319bc1a2270d352e0ded6d6386242a7ef Mon Sep 17 00:00:00 2001 +From: John Crispin +Date: Tue, 12 Aug 2014 20:49:27 +0200 +Subject: [PATCH 24/53] GPIO: add named gpio exports + +Signed-off-by: John Crispin +--- + drivers/gpio/gpiolib-of.c | 68 +++++++++++++++++++++++++++++++++++++++++ + drivers/gpio/gpiolib-sysfs.c | 10 +++++- + include/asm-generic/gpio.h | 6 ++++ + include/linux/gpio/consumer.h | 8 +++++ + 4 files changed, 91 insertions(+), 1 deletion(-) + +--- a/drivers/gpio/gpiolib-of.c ++++ b/drivers/gpio/gpiolib-of.c +@@ -23,6 +23,8 @@ + #include + #include + #include ++#include ++#include + + #include "gpiolib.h" + +@@ -513,3 +515,68 @@ void of_gpiochip_remove(struct gpio_chip + gpiochip_remove_pin_ranges(chip); + of_node_put(chip->of_node); + } ++ ++static struct of_device_id gpio_export_ids[] = { ++ { .compatible = "gpio-export" }, ++ { /* sentinel */ } ++}; ++ ++static int of_gpio_export_probe(struct platform_device *pdev) ++{ ++ struct device_node *np = pdev->dev.of_node; ++ struct device_node *cnp; ++ u32 val; ++ int nb = 0; ++ ++ for_each_child_of_node(np, cnp) { ++ const char *name = NULL; ++ int gpio; ++ bool dmc; ++ int max_gpio = 1; ++ int i; ++ ++ of_property_read_string(cnp, "gpio-export,name", &name); ++ ++ if (!name) ++ max_gpio = of_gpio_count(cnp); ++ ++ for (i = 0; i < max_gpio; i++) { ++ unsigned flags = 0; ++ enum of_gpio_flags of_flags; ++ ++ gpio = of_get_gpio_flags(cnp, i, &of_flags); ++ if (!gpio_is_valid(gpio)) ++ return gpio; ++ ++ if (of_flags == OF_GPIO_ACTIVE_LOW) ++ flags |= GPIOF_ACTIVE_LOW; ++ ++ if (!of_property_read_u32(cnp, "gpio-export,output", &val)) ++ flags |= val ? GPIOF_OUT_INIT_HIGH : GPIOF_OUT_INIT_LOW; ++ else ++ flags |= GPIOF_IN; ++ ++ if (devm_gpio_request_one(&pdev->dev, gpio, flags, name ? name : of_node_full_name(np))) ++ continue; ++ ++ dmc = of_property_read_bool(cnp, "gpio-export,direction_may_change"); ++ gpio_export_with_name(gpio, dmc, name); ++ nb++; ++ } ++ } ++ ++ dev_info(&pdev->dev, "%d gpio(s) exported\n", nb); ++ ++ return 0; ++} ++ ++static struct platform_driver gpio_export_driver = { ++ .driver = { ++ .name = "gpio-export", ++ .owner = THIS_MODULE, ++ .of_match_table = of_match_ptr(gpio_export_ids), ++ }, ++ .probe = of_gpio_export_probe, ++}; ++ ++module_platform_driver(gpio_export_driver); +--- a/drivers/gpio/gpiolib-sysfs.c ++++ b/drivers/gpio/gpiolib-sysfs.c +@@ -553,7 +553,7 @@ static struct class gpio_class = { + * + * Returns zero on success, else an error. + */ +-int gpiod_export(struct gpio_desc *desc, bool direction_may_change) ++int __gpiod_export(struct gpio_desc *desc, bool direction_may_change, const char *name) + { + struct gpio_chip *chip; + struct gpio_device *gdev; +@@ -615,6 +615,8 @@ int gpiod_export(struct gpio_desc *desc, + offset = gpio_chip_hwgpio(desc); + if (chip->names && chip->names[offset]) + ioname = chip->names[offset]; ++ if (name) ++ ioname = name; + + dev = device_create_with_groups(&gpio_class, &gdev->dev, + MKDEV(0, 0), data, gpio_groups, +@@ -636,6 +638,12 @@ err_unlock: + gpiod_dbg(desc, "%s: status %d\n", __func__, status); + return status; + } ++EXPORT_SYMBOL_GPL(__gpiod_export); ++ ++int gpiod_export(struct gpio_desc *desc, bool direction_may_change) ++{ ++ return __gpiod_export(desc, direction_may_change, NULL); ++} + EXPORT_SYMBOL_GPL(gpiod_export); + + static int match_export(struct device *dev, const void *desc) +--- a/include/asm-generic/gpio.h ++++ b/include/asm-generic/gpio.h +@@ -127,6 +127,12 @@ static inline int gpio_export(unsigned g + return gpiod_export(gpio_to_desc(gpio), direction_may_change); + } + ++int __gpiod_export(struct gpio_desc *desc, bool direction_may_change, const char *name); ++static inline int gpio_export_with_name(unsigned gpio, bool direction_may_change, const char *name) ++{ ++ return __gpiod_export(gpio_to_desc(gpio), direction_may_change, name); ++} ++ + static inline int gpio_export_link(struct device *dev, const char *name, + unsigned gpio) + { +--- a/include/linux/gpio/consumer.h ++++ b/include/linux/gpio/consumer.h +@@ -451,6 +451,7 @@ struct gpio_desc *devm_fwnode_get_gpiod_ + + #if IS_ENABLED(CONFIG_GPIOLIB) && IS_ENABLED(CONFIG_GPIO_SYSFS) + ++int _gpiod_export(struct gpio_desc *desc, bool direction_may_change, const char *name); + int gpiod_export(struct gpio_desc *desc, bool direction_may_change); + int gpiod_export_link(struct device *dev, const char *name, + struct gpio_desc *desc); +@@ -458,6 +459,13 @@ void gpiod_unexport(struct gpio_desc *de + + #else /* CONFIG_GPIOLIB && CONFIG_GPIO_SYSFS */ + ++static inline int _gpiod_export(struct gpio_desc *desc, ++ bool direction_may_change, ++ const char *name) ++{ ++ return -ENOSYS; ++} ++ + static inline int gpiod_export(struct gpio_desc *desc, + bool direction_may_change) + { diff --git a/target/linux/ramips/patches-5.4/0025-pinctrl-ralink-add-pinctrl-driver.patch b/target/linux/ramips/patches-5.4/0025-pinctrl-ralink-add-pinctrl-driver.patch new file mode 100644 index 0000000000..a374e01b59 --- /dev/null +++ b/target/linux/ramips/patches-5.4/0025-pinctrl-ralink-add-pinctrl-driver.patch @@ -0,0 +1,524 @@ +From 7adbe9a88c33c6e362a10b109d963b5500a21f00 Mon Sep 17 00:00:00 2001 +From: John Crispin +Date: Sun, 27 Jul 2014 09:34:05 +0100 +Subject: [PATCH 25/53] pinctrl: ralink: add pinctrl driver + +Signed-off-by: John Crispin +--- + arch/mips/Kconfig | 2 + + drivers/pinctrl/Kconfig | 5 + + drivers/pinctrl/Makefile | 1 + + drivers/pinctrl/pinctrl-rt2880.c | 474 ++++++++++++++++++++++++++++++++++++++ + 4 files changed, 482 insertions(+) + create mode 100644 drivers/pinctrl/pinctrl-rt2880.c + +--- a/arch/mips/Kconfig ++++ b/arch/mips/Kconfig +@@ -629,6 +629,8 @@ config RALINK + select CLKDEV_LOOKUP + select ARCH_HAS_RESET_CONTROLLER + select RESET_CONTROLLER ++ select PINCTRL ++ select PINCTRL_RT2880 + + config SGI_IP22 + bool "SGI IP22 (Indy/Indigo2)" +--- a/drivers/pinctrl/Kconfig ++++ b/drivers/pinctrl/Kconfig +@@ -143,6 +143,11 @@ config PINCTRL_LPC18XX + help + Pinctrl driver for NXP LPC18xx/43xx System Control Unit (SCU). + ++config PINCTRL_RT2880 ++ bool ++ depends on RALINK ++ select PINMUX ++ + config PINCTRL_FALCON + bool + depends on SOC_FALCON +--- a/drivers/pinctrl/Makefile ++++ b/drivers/pinctrl/Makefile +@@ -28,6 +28,7 @@ obj-$(CONFIG_PINCTRL_PALMAS) += pinctrl- + obj-$(CONFIG_PINCTRL_PIC32) += pinctrl-pic32.o + obj-$(CONFIG_PINCTRL_PISTACHIO) += pinctrl-pistachio.o + obj-$(CONFIG_PINCTRL_ROCKCHIP) += pinctrl-rockchip.o ++obj-$(CONFIG_PINCTRL_RT2880) += pinctrl-rt2880.o + obj-$(CONFIG_PINCTRL_RZA1) += pinctrl-rza1.o + obj-$(CONFIG_PINCTRL_SINGLE) += pinctrl-single.o + obj-$(CONFIG_PINCTRL_SIRF) += sirf/ +--- /dev/null ++++ b/drivers/pinctrl/pinctrl-rt2880.c +@@ -0,0 +1,472 @@ ++/* ++ * linux/drivers/pinctrl/pinctrl-rt2880.c ++ * ++ * This program is free software; you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License version 2 as ++ * publishhed by the Free Software Foundation. ++ * ++ * Copyright (C) 2013 John Crispin ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#include ++#include ++#include ++ ++#include "core.h" ++ ++#define SYSC_REG_GPIO_MODE 0x60 ++#define SYSC_REG_GPIO_MODE2 0x64 ++ ++struct rt2880_priv { ++ struct device *dev; ++ ++ struct pinctrl_pin_desc *pads; ++ struct pinctrl_desc *desc; ++ ++ struct rt2880_pmx_func **func; ++ int func_count; ++ ++ struct rt2880_pmx_group *groups; ++ const char **group_names; ++ int group_count; ++ ++ uint8_t *gpio; ++ int max_pins; ++}; ++ ++static int rt2880_get_group_count(struct pinctrl_dev *pctrldev) ++{ ++ struct rt2880_priv *p = pinctrl_dev_get_drvdata(pctrldev); ++ ++ return p->group_count; ++} ++ ++static const char *rt2880_get_group_name(struct pinctrl_dev *pctrldev, ++ unsigned group) ++{ ++ struct rt2880_priv *p = pinctrl_dev_get_drvdata(pctrldev); ++ ++ if (group >= p->group_count) ++ return NULL; ++ ++ return p->group_names[group]; ++} ++ ++static int rt2880_get_group_pins(struct pinctrl_dev *pctrldev, ++ unsigned group, ++ const unsigned **pins, ++ unsigned *num_pins) ++{ ++ struct rt2880_priv *p = pinctrl_dev_get_drvdata(pctrldev); ++ ++ if (group >= p->group_count) ++ return -EINVAL; ++ ++ *pins = p->groups[group].func[0].pins; ++ *num_pins = p->groups[group].func[0].pin_count; ++ ++ return 0; ++} ++ ++static void rt2880_pinctrl_dt_free_map(struct pinctrl_dev *pctrldev, ++ struct pinctrl_map *map, unsigned num_maps) ++{ ++ int i; ++ ++ for (i = 0; i < num_maps; i++) ++ if (map[i].type == PIN_MAP_TYPE_CONFIGS_PIN || ++ map[i].type == PIN_MAP_TYPE_CONFIGS_GROUP) ++ kfree(map[i].data.configs.configs); ++ kfree(map); ++} ++ ++static void rt2880_pinctrl_pin_dbg_show(struct pinctrl_dev *pctrldev, ++ struct seq_file *s, ++ unsigned offset) ++{ ++ seq_printf(s, "ralink pio"); ++} ++ ++static void rt2880_pinctrl_dt_subnode_to_map(struct pinctrl_dev *pctrldev, ++ struct device_node *np, ++ struct pinctrl_map **map) ++{ ++ const char *function; ++ int func = of_property_read_string(np, "ralink,function", &function); ++ int grps = of_property_count_strings(np, "ralink,group"); ++ int i; ++ ++ if (func || !grps) ++ return; ++ ++ for (i = 0; i < grps; i++) { ++ const char *group; ++ ++ of_property_read_string_index(np, "ralink,group", i, &group); ++ ++ (*map)->type = PIN_MAP_TYPE_MUX_GROUP; ++ (*map)->name = function; ++ (*map)->data.mux.group = group; ++ (*map)->data.mux.function = function; ++ (*map)++; ++ } ++} ++ ++static int rt2880_pinctrl_dt_node_to_map(struct pinctrl_dev *pctrldev, ++ struct device_node *np_config, ++ struct pinctrl_map **map, ++ unsigned *num_maps) ++{ ++ int max_maps = 0; ++ struct pinctrl_map *tmp; ++ struct device_node *np; ++ ++ for_each_child_of_node(np_config, np) { ++ int ret = of_property_count_strings(np, "ralink,group"); ++ ++ if (ret >= 0) ++ max_maps += ret; ++ } ++ ++ if (!max_maps) ++ return -EINVAL; ++ ++ *map = kzalloc(max_maps * sizeof(struct pinctrl_map), GFP_KERNEL); ++ if (!*map) ++ return -ENOMEM; ++ ++ tmp = *map; ++ ++ for_each_child_of_node(np_config, np) ++ rt2880_pinctrl_dt_subnode_to_map(pctrldev, np, &tmp); ++ *num_maps = max_maps; ++ ++ return 0; ++} ++ ++static const struct pinctrl_ops rt2880_pctrl_ops = { ++ .get_groups_count = rt2880_get_group_count, ++ .get_group_name = rt2880_get_group_name, ++ .get_group_pins = rt2880_get_group_pins, ++ .pin_dbg_show = rt2880_pinctrl_pin_dbg_show, ++ .dt_node_to_map = rt2880_pinctrl_dt_node_to_map, ++ .dt_free_map = rt2880_pinctrl_dt_free_map, ++}; ++ ++static int rt2880_pmx_func_count(struct pinctrl_dev *pctrldev) ++{ ++ struct rt2880_priv *p = pinctrl_dev_get_drvdata(pctrldev); ++ ++ return p->func_count; ++} ++ ++static const char *rt2880_pmx_func_name(struct pinctrl_dev *pctrldev, ++ unsigned func) ++{ ++ struct rt2880_priv *p = pinctrl_dev_get_drvdata(pctrldev); ++ ++ return p->func[func]->name; ++} ++ ++static int rt2880_pmx_group_get_groups(struct pinctrl_dev *pctrldev, ++ unsigned func, ++ const char * const **groups, ++ unsigned * const num_groups) ++{ ++ struct rt2880_priv *p = pinctrl_dev_get_drvdata(pctrldev); ++ ++ if (p->func[func]->group_count == 1) ++ *groups = &p->group_names[p->func[func]->groups[0]]; ++ else ++ *groups = p->group_names; ++ ++ *num_groups = p->func[func]->group_count; ++ ++ return 0; ++} ++ ++static int rt2880_pmx_group_enable(struct pinctrl_dev *pctrldev, ++ unsigned func, ++ unsigned group) ++{ ++ struct rt2880_priv *p = pinctrl_dev_get_drvdata(pctrldev); ++ u32 mode = 0; ++ u32 reg = SYSC_REG_GPIO_MODE; ++ int i; ++ int shift; ++ ++ /* dont allow double use */ ++ if (p->groups[group].enabled) { ++ dev_err(p->dev, "%s is already enabled\n", p->groups[group].name); ++ return -EBUSY; ++ } ++ ++ p->groups[group].enabled = 1; ++ p->func[func]->enabled = 1; ++ ++ shift = p->groups[group].shift; ++ if (shift >= 32) { ++ shift -= 32; ++ reg = SYSC_REG_GPIO_MODE2; ++ } ++ mode = rt_sysc_r32(reg); ++ mode &= ~(p->groups[group].mask << shift); ++ ++ /* mark the pins as gpio */ ++ for (i = 0; i < p->groups[group].func[0].pin_count; i++) ++ p->gpio[p->groups[group].func[0].pins[i]] = 1; ++ ++ /* function 0 is gpio and needs special handling */ ++ if (func == 0) { ++ mode |= p->groups[group].gpio << shift; ++ } else { ++ for (i = 0; i < p->func[func]->pin_count; i++) ++ p->gpio[p->func[func]->pins[i]] = 0; ++ mode |= p->func[func]->value << shift; ++ } ++ rt_sysc_w32(mode, reg); ++ ++ return 0; ++} ++ ++static int rt2880_pmx_group_gpio_request_enable(struct pinctrl_dev *pctrldev, ++ struct pinctrl_gpio_range *range, ++ unsigned pin) ++{ ++ struct rt2880_priv *p = pinctrl_dev_get_drvdata(pctrldev); ++ ++ if (!p->gpio[pin]) { ++ dev_err(p->dev, "pin %d is not set to gpio mux\n", pin); ++ return -EINVAL; ++ } ++ ++ return 0; ++} ++ ++static const struct pinmux_ops rt2880_pmx_group_ops = { ++ .get_functions_count = rt2880_pmx_func_count, ++ .get_function_name = rt2880_pmx_func_name, ++ .get_function_groups = rt2880_pmx_group_get_groups, ++ .set_mux = rt2880_pmx_group_enable, ++ .gpio_request_enable = rt2880_pmx_group_gpio_request_enable, ++}; ++ ++static struct pinctrl_desc rt2880_pctrl_desc = { ++ .owner = THIS_MODULE, ++ .name = "rt2880-pinmux", ++ .pctlops = &rt2880_pctrl_ops, ++ .pmxops = &rt2880_pmx_group_ops, ++}; ++ ++static struct rt2880_pmx_func gpio_func = { ++ .name = "gpio", ++}; ++ ++static int rt2880_pinmux_index(struct rt2880_priv *p) ++{ ++ struct rt2880_pmx_func **f; ++ struct rt2880_pmx_group *mux = p->groups; ++ int i, j, c = 0; ++ ++ /* count the mux functions */ ++ while (mux->name) { ++ p->group_count++; ++ mux++; ++ } ++ ++ /* allocate the group names array needed by the gpio function */ ++ p->group_names = devm_kzalloc(p->dev, sizeof(char *) * p->group_count, GFP_KERNEL); ++ if (!p->group_names) ++ return -1; ++ ++ for (i = 0; i < p->group_count; i++) { ++ p->group_names[i] = p->groups[i].name; ++ p->func_count += p->groups[i].func_count; ++ } ++ ++ /* we have a dummy function[0] for gpio */ ++ p->func_count++; ++ ++ /* allocate our function and group mapping index buffers */ ++ f = p->func = devm_kzalloc(p->dev, sizeof(struct rt2880_pmx_func) * p->func_count, GFP_KERNEL); ++ gpio_func.groups = devm_kzalloc(p->dev, sizeof(int) * p->group_count, GFP_KERNEL); ++ if (!f || !gpio_func.groups) ++ return -1; ++ ++ /* add a backpointer to the function so it knows its group */ ++ gpio_func.group_count = p->group_count; ++ for (i = 0; i < gpio_func.group_count; i++) ++ gpio_func.groups[i] = i; ++ ++ f[c] = &gpio_func; ++ c++; ++ ++ /* add remaining functions */ ++ for (i = 0; i < p->group_count; i++) { ++ for (j = 0; j < p->groups[i].func_count; j++) { ++ f[c] = &p->groups[i].func[j]; ++ f[c]->groups = devm_kzalloc(p->dev, sizeof(int), GFP_KERNEL); ++ f[c]->groups[0] = i; ++ f[c]->group_count = 1; ++ c++; ++ } ++ } ++ return 0; ++} ++ ++static int rt2880_pinmux_pins(struct rt2880_priv *p) ++{ ++ int i, j; ++ ++ /* loop over the functions and initialize the pins array. also work out the highest pin used */ ++ for (i = 0; i < p->func_count; i++) { ++ int pin; ++ ++ if (!p->func[i]->pin_count) ++ continue; ++ ++ p->func[i]->pins = devm_kzalloc(p->dev, sizeof(int) * p->func[i]->pin_count, GFP_KERNEL); ++ for (j = 0; j < p->func[i]->pin_count; j++) ++ p->func[i]->pins[j] = p->func[i]->pin_first + j; ++ ++ pin = p->func[i]->pin_first + p->func[i]->pin_count; ++ if (pin > p->max_pins) ++ p->max_pins = pin; ++ } ++ ++ /* the buffer that tells us which pins are gpio */ ++ p->gpio = devm_kzalloc(p->dev,sizeof(uint8_t) * p->max_pins, ++ GFP_KERNEL); ++ /* the pads needed to tell pinctrl about our pins */ ++ p->pads = devm_kzalloc(p->dev, ++ sizeof(struct pinctrl_pin_desc) * p->max_pins, ++ GFP_KERNEL); ++ if (!p->pads || !p->gpio ) { ++ dev_err(p->dev, "Failed to allocate gpio data\n"); ++ return -ENOMEM; ++ } ++ ++ memset(p->gpio, 1, sizeof(uint8_t) * p->max_pins); ++ for (i = 0; i < p->func_count; i++) { ++ if (!p->func[i]->pin_count) ++ continue; ++ ++ for (j = 0; j < p->func[i]->pin_count; j++) ++ p->gpio[p->func[i]->pins[j]] = 0; ++ } ++ ++ /* pin 0 is always a gpio */ ++ p->gpio[0] = 1; ++ ++ /* set the pads */ ++ for (i = 0; i < p->max_pins; i++) { ++ /* strlen("ioXY") + 1 = 5 */ ++ char *name = devm_kzalloc(p->dev, 5, GFP_KERNEL); ++ ++ if (!name) { ++ dev_err(p->dev, "Failed to allocate pad name\n"); ++ return -ENOMEM; ++ } ++ snprintf(name, 5, "io%d", i); ++ p->pads[i].number = i; ++ p->pads[i].name = name; ++ } ++ p->desc->pins = p->pads; ++ p->desc->npins = p->max_pins; ++ ++ return 0; ++} ++ ++static int rt2880_pinmux_probe(struct platform_device *pdev) ++{ ++ struct rt2880_priv *p; ++ struct pinctrl_dev *dev; ++ struct device_node *np; ++ ++ if (!rt2880_pinmux_data) ++ return -ENOSYS; ++ ++ /* setup the private data */ ++ p = devm_kzalloc(&pdev->dev, sizeof(struct rt2880_priv), GFP_KERNEL); ++ if (!p) ++ return -ENOMEM; ++ ++ p->dev = &pdev->dev; ++ p->desc = &rt2880_pctrl_desc; ++ p->groups = rt2880_pinmux_data; ++ platform_set_drvdata(pdev, p); ++ ++ /* init the device */ ++ if (rt2880_pinmux_index(p)) { ++ dev_err(&pdev->dev, "failed to load index\n"); ++ return -EINVAL; ++ } ++ if (rt2880_pinmux_pins(p)) { ++ dev_err(&pdev->dev, "failed to load pins\n"); ++ return -EINVAL; ++ } ++ dev = pinctrl_register(p->desc, &pdev->dev, p); ++ if (IS_ERR(dev)) ++ return PTR_ERR(dev); ++ ++ /* finalize by adding gpio ranges for enables gpio controllers */ ++ for_each_compatible_node(np, NULL, "ralink,rt2880-gpio") { ++ const __be32 *ngpio, *gpiobase; ++ struct pinctrl_gpio_range *range; ++ char *name; ++ ++ if (!of_device_is_available(np)) ++ continue; ++ ++ ngpio = of_get_property(np, "ralink,nr-gpio", NULL); ++ gpiobase = of_get_property(np, "ralink,gpio-base", NULL); ++ if (!ngpio || !gpiobase) { ++ dev_err(&pdev->dev, "failed to load chip info\n"); ++ return -EINVAL; ++ } ++ ++ range = devm_kzalloc(p->dev, sizeof(struct pinctrl_gpio_range) + 4, GFP_KERNEL); ++ range->name = name = (char *) &range[1]; ++ sprintf(name, "pio"); ++ range->npins = __be32_to_cpu(*ngpio); ++ range->base = __be32_to_cpu(*gpiobase); ++ range->pin_base = range->base; ++ pinctrl_add_gpio_range(dev, range); ++ } ++ ++ return 0; ++} ++ ++static const struct of_device_id rt2880_pinmux_match[] = { ++ { .compatible = "ralink,rt2880-pinmux" }, ++ {}, ++}; ++MODULE_DEVICE_TABLE(of, rt2880_pinmux_match); ++ ++static struct platform_driver rt2880_pinmux_driver = { ++ .probe = rt2880_pinmux_probe, ++ .driver = { ++ .name = "rt2880-pinmux", ++ .owner = THIS_MODULE, ++ .of_match_table = rt2880_pinmux_match, ++ }, ++}; ++ ++int __init rt2880_pinmux_init(void) ++{ ++ return platform_driver_register(&rt2880_pinmux_driver); ++} ++ ++core_initcall_sync(rt2880_pinmux_init); diff --git a/target/linux/ramips/patches-5.4/0026-DT-Add-documentation-for-gpio-ralink.patch b/target/linux/ramips/patches-5.4/0026-DT-Add-documentation-for-gpio-ralink.patch new file mode 100644 index 0000000000..0bce0b433a --- /dev/null +++ b/target/linux/ramips/patches-5.4/0026-DT-Add-documentation-for-gpio-ralink.patch @@ -0,0 +1,59 @@ +From d410e5478c622c01fcf31427533df5f433df9146 Mon Sep 17 00:00:00 2001 +From: John Crispin +Date: Sun, 28 Jul 2013 19:45:30 +0200 +Subject: [PATCH 26/53] DT: Add documentation for gpio-ralink + +Describe gpio-ralink binding. + +Signed-off-by: John Crispin +Cc: linux-mips@linux-mips.org +Cc: devicetree@vger.kernel.org +Cc: linux-gpio@vger.kernel.org +--- + .../devicetree/bindings/gpio/gpio-ralink.txt | 40 ++++++++++++++++++++ + 1 file changed, 40 insertions(+) + create mode 100644 Documentation/devicetree/bindings/gpio/gpio-ralink.txt + +--- /dev/null ++++ b/Documentation/devicetree/bindings/gpio/gpio-ralink.txt +@@ -0,0 +1,40 @@ ++Ralink SoC GPIO controller bindings ++ ++Required properties: ++- compatible: ++ - "ralink,rt2880-gpio" for Ralink controllers ++- #gpio-cells : Should be two. ++ - first cell is the pin number ++ - second cell is used to specify optional parameters (unused) ++- gpio-controller : Marks the device node as a GPIO controller ++- reg : Physical base address and length of the controller's registers ++- interrupt-parent: phandle to the INTC device node ++- interrupts : Specify the INTC interrupt number ++- ralink,nr-gpio : Specify the number of GPIOs ++- ralink,register-map : The register layout depends on the GPIO bank and actual ++ SoC type. Register offsets need to be in this order. ++ [ INT, EDGE, RENA, FENA, DATA, DIR, POL, SET, RESET, TOGGLE ] ++ ++Optional properties: ++- ralink,gpio-base : Specify the GPIO chips base number ++ ++Example: ++ ++ gpio0: gpio@600 { ++ compatible = "ralink,rt5350-gpio", "ralink,rt2880-gpio"; ++ ++ #gpio-cells = <2>; ++ gpio-controller; ++ ++ reg = <0x600 0x34>; ++ ++ interrupt-parent = <&intc>; ++ interrupts = <6>; ++ ++ ralink,gpio-base = <0>; ++ ralink,nr-gpio = <24>; ++ ralink,register-map = [ 00 04 08 0c ++ 20 24 28 2c ++ 30 34 ]; ++ ++ }; diff --git a/target/linux/ramips/patches-5.4/0027-GPIO-MIPS-ralink-add-gpio-driver-for-ralink-SoC.patch b/target/linux/ramips/patches-5.4/0027-GPIO-MIPS-ralink-add-gpio-driver-for-ralink-SoC.patch new file mode 100644 index 0000000000..eaae0d3d02 --- /dev/null +++ b/target/linux/ramips/patches-5.4/0027-GPIO-MIPS-ralink-add-gpio-driver-for-ralink-SoC.patch @@ -0,0 +1,430 @@ +From 69fdd2c4f937796b934e89c33acde9d082e27bfd Mon Sep 17 00:00:00 2001 +From: John Crispin +Date: Mon, 4 Aug 2014 20:36:29 +0200 +Subject: [PATCH 27/53] GPIO: MIPS: ralink: add gpio driver for ralink SoC + +Add gpio driver for Ralink SoC. This driver makes the gpio core on +RT2880, RT305x, rt3352, rt3662, rt3883, rt5350 and mt7620 work. + +Signed-off-by: John Crispin +Cc: linux-mips@linux-mips.org +Cc: linux-gpio@vger.kernel.org +--- + arch/mips/include/asm/mach-ralink/gpio.h | 24 ++ + drivers/gpio/Kconfig | 6 + + drivers/gpio/Makefile | 1 + + drivers/gpio/gpio-ralink.c | 355 ++++++++++++++++++++++++++++++ + 4 files changed, 386 insertions(+) + create mode 100644 arch/mips/include/asm/mach-ralink/gpio.h + create mode 100644 drivers/gpio/gpio-ralink.c + +--- /dev/null ++++ b/arch/mips/include/asm/mach-ralink/gpio.h +@@ -0,0 +1,24 @@ ++/* ++ * Ralink SoC GPIO API support ++ * ++ * Copyright (C) 2008-2009 Gabor Juhos ++ * Copyright (C) 2008 Imre Kaloz ++ * ++ * This program is free software; you can redistribute it and/or modify it ++ * under the terms of the GNU General Public License version 2 as published ++ * by the Free Software Foundation. ++ * ++ */ ++ ++#ifndef __ASM_MACH_RALINK_GPIO_H ++#define __ASM_MACH_RALINK_GPIO_H ++ ++#define ARCH_NR_GPIOS 128 ++#include ++ ++#define gpio_get_value __gpio_get_value ++#define gpio_set_value __gpio_set_value ++#define gpio_cansleep __gpio_cansleep ++#define gpio_to_irq __gpio_to_irq ++ ++#endif /* __ASM_MACH_RALINK_GPIO_H */ +--- a/drivers/gpio/Kconfig ++++ b/drivers/gpio/Kconfig +@@ -398,6 +398,12 @@ config GPIO_REG + A 32-bit single register GPIO fixed in/out implementation. This + can be used to represent any register as a set of GPIO signals. + ++config GPIO_RALINK ++ bool "Ralink GPIO Support" ++ depends on RALINK ++ help ++ Say yes here to support the Ralink SoC GPIO device ++ + config GPIO_SPEAR_SPICS + bool "ST SPEAr13xx SPI Chip Select as GPIO support" + depends on PLAT_SPEAR +--- a/drivers/gpio/Makefile ++++ b/drivers/gpio/Makefile +@@ -98,6 +98,7 @@ obj-$(CONFIG_GPIO_PCI_IDIO_16) += gpio-p + obj-$(CONFIG_GPIO_PISOSR) += gpio-pisosr.o + obj-$(CONFIG_GPIO_PL061) += gpio-pl061.o + obj-$(CONFIG_GPIO_PXA) += gpio-pxa.o ++obj-$(CONFIG_GPIO_RALINK) += gpio-ralink.o + obj-$(CONFIG_GPIO_RC5T583) += gpio-rc5t583.o + obj-$(CONFIG_GPIO_RDC321X) += gpio-rdc321x.o + obj-$(CONFIG_GPIO_RCAR) += gpio-rcar.o +--- /dev/null ++++ b/drivers/gpio/gpio-ralink.c +@@ -0,0 +1,355 @@ ++/* ++ * This program is free software; you can redistribute it and/or modify it ++ * under the terms of the GNU General Public License version 2 as published ++ * by the Free Software Foundation. ++ * ++ * Copyright (C) 2009-2011 Gabor Juhos ++ * Copyright (C) 2013 John Crispin ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++enum ralink_gpio_reg { ++ GPIO_REG_INT = 0, ++ GPIO_REG_EDGE, ++ GPIO_REG_RENA, ++ GPIO_REG_FENA, ++ GPIO_REG_DATA, ++ GPIO_REG_DIR, ++ GPIO_REG_POL, ++ GPIO_REG_SET, ++ GPIO_REG_RESET, ++ GPIO_REG_TOGGLE, ++ GPIO_REG_MAX ++}; ++ ++struct ralink_gpio_chip { ++ struct gpio_chip chip; ++ u8 regs[GPIO_REG_MAX]; ++ ++ spinlock_t lock; ++ void __iomem *membase; ++ struct irq_domain *domain; ++ int irq; ++ ++ u32 rising; ++ u32 falling; ++}; ++ ++#define MAP_MAX 4 ++static struct irq_domain *irq_map[MAP_MAX]; ++static int irq_map_count; ++static atomic_t irq_refcount = ATOMIC_INIT(0); ++ ++static inline struct ralink_gpio_chip *to_ralink_gpio(struct gpio_chip *chip) ++{ ++ struct ralink_gpio_chip *rg; ++ ++ rg = container_of(chip, struct ralink_gpio_chip, chip); ++ ++ return rg; ++} ++ ++static inline void rt_gpio_w32(struct ralink_gpio_chip *rg, u8 reg, u32 val) ++{ ++ iowrite32(val, rg->membase + rg->regs[reg]); ++} ++ ++static inline u32 rt_gpio_r32(struct ralink_gpio_chip *rg, u8 reg) ++{ ++ return ioread32(rg->membase + rg->regs[reg]); ++} ++ ++static void ralink_gpio_set(struct gpio_chip *chip, unsigned offset, int value) ++{ ++ struct ralink_gpio_chip *rg = to_ralink_gpio(chip); ++ ++ rt_gpio_w32(rg, (value) ? GPIO_REG_SET : GPIO_REG_RESET, BIT(offset)); ++} ++ ++static int ralink_gpio_get(struct gpio_chip *chip, unsigned offset) ++{ ++ struct ralink_gpio_chip *rg = to_ralink_gpio(chip); ++ ++ return !!(rt_gpio_r32(rg, GPIO_REG_DATA) & BIT(offset)); ++} ++ ++static int ralink_gpio_direction_input(struct gpio_chip *chip, unsigned offset) ++{ ++ struct ralink_gpio_chip *rg = to_ralink_gpio(chip); ++ unsigned long flags; ++ u32 t; ++ ++ spin_lock_irqsave(&rg->lock, flags); ++ t = rt_gpio_r32(rg, GPIO_REG_DIR); ++ t &= ~BIT(offset); ++ rt_gpio_w32(rg, GPIO_REG_DIR, t); ++ spin_unlock_irqrestore(&rg->lock, flags); ++ ++ return 0; ++} ++ ++static int ralink_gpio_direction_output(struct gpio_chip *chip, ++ unsigned offset, int value) ++{ ++ struct ralink_gpio_chip *rg = to_ralink_gpio(chip); ++ unsigned long flags; ++ u32 t; ++ ++ spin_lock_irqsave(&rg->lock, flags); ++ ralink_gpio_set(chip, offset, value); ++ t = rt_gpio_r32(rg, GPIO_REG_DIR); ++ t |= BIT(offset); ++ rt_gpio_w32(rg, GPIO_REG_DIR, t); ++ spin_unlock_irqrestore(&rg->lock, flags); ++ ++ return 0; ++} ++ ++static int ralink_gpio_to_irq(struct gpio_chip *chip, unsigned pin) ++{ ++ struct ralink_gpio_chip *rg = to_ralink_gpio(chip); ++ ++ if (rg->irq < 1) ++ return -1; ++ ++ return irq_create_mapping(rg->domain, pin); ++} ++ ++static void ralink_gpio_irq_handler(struct irq_desc *desc) ++{ ++ int i; ++ ++ for (i = 0; i < irq_map_count; i++) { ++ struct irq_domain *domain = irq_map[i]; ++ struct ralink_gpio_chip *rg; ++ unsigned long pending; ++ int bit; ++ ++ rg = (struct ralink_gpio_chip *) domain->host_data; ++ pending = rt_gpio_r32(rg, GPIO_REG_INT); ++ ++ for_each_set_bit(bit, &pending, rg->chip.ngpio) { ++ u32 map = irq_find_mapping(domain, bit); ++ generic_handle_irq(map); ++ rt_gpio_w32(rg, GPIO_REG_INT, BIT(bit)); ++ } ++ } ++} ++ ++static void ralink_gpio_irq_unmask(struct irq_data *d) ++{ ++ struct ralink_gpio_chip *rg; ++ unsigned long flags; ++ u32 rise, fall; ++ ++ rg = (struct ralink_gpio_chip *) d->domain->host_data; ++ rise = rt_gpio_r32(rg, GPIO_REG_RENA); ++ fall = rt_gpio_r32(rg, GPIO_REG_FENA); ++ ++ spin_lock_irqsave(&rg->lock, flags); ++ rt_gpio_w32(rg, GPIO_REG_RENA, rise | (BIT(d->hwirq) & rg->rising)); ++ rt_gpio_w32(rg, GPIO_REG_FENA, fall | (BIT(d->hwirq) & rg->falling)); ++ spin_unlock_irqrestore(&rg->lock, flags); ++} ++ ++static void ralink_gpio_irq_mask(struct irq_data *d) ++{ ++ struct ralink_gpio_chip *rg; ++ unsigned long flags; ++ u32 rise, fall; ++ ++ rg = (struct ralink_gpio_chip *) d->domain->host_data; ++ rise = rt_gpio_r32(rg, GPIO_REG_RENA); ++ fall = rt_gpio_r32(rg, GPIO_REG_FENA); ++ ++ spin_lock_irqsave(&rg->lock, flags); ++ rt_gpio_w32(rg, GPIO_REG_FENA, fall & ~BIT(d->hwirq)); ++ rt_gpio_w32(rg, GPIO_REG_RENA, rise & ~BIT(d->hwirq)); ++ spin_unlock_irqrestore(&rg->lock, flags); ++} ++ ++static int ralink_gpio_irq_type(struct irq_data *d, unsigned int type) ++{ ++ struct ralink_gpio_chip *rg; ++ u32 mask = BIT(d->hwirq); ++ ++ rg = (struct ralink_gpio_chip *) d->domain->host_data; ++ ++ if (type == IRQ_TYPE_PROBE) { ++ if ((rg->rising | rg->falling) & mask) ++ return 0; ++ ++ type = IRQ_TYPE_EDGE_RISING | IRQ_TYPE_EDGE_FALLING; ++ } ++ ++ if (type & IRQ_TYPE_EDGE_RISING) ++ rg->rising |= mask; ++ else ++ rg->rising &= ~mask; ++ ++ if (type & IRQ_TYPE_EDGE_FALLING) ++ rg->falling |= mask; ++ else ++ rg->falling &= ~mask; ++ ++ return 0; ++} ++ ++static struct irq_chip ralink_gpio_irq_chip = { ++ .name = "GPIO", ++ .irq_unmask = ralink_gpio_irq_unmask, ++ .irq_mask = ralink_gpio_irq_mask, ++ .irq_mask_ack = ralink_gpio_irq_mask, ++ .irq_set_type = ralink_gpio_irq_type, ++}; ++ ++static int gpio_map(struct irq_domain *d, unsigned int irq, irq_hw_number_t hw) ++{ ++ irq_set_chip_and_handler(irq, &ralink_gpio_irq_chip, handle_level_irq); ++ irq_set_handler_data(irq, d); ++ ++ return 0; ++} ++ ++static const struct irq_domain_ops irq_domain_ops = { ++ .xlate = irq_domain_xlate_onecell, ++ .map = gpio_map, ++}; ++ ++static void ralink_gpio_irq_init(struct device_node *np, ++ struct ralink_gpio_chip *rg) ++{ ++ if (irq_map_count >= MAP_MAX) ++ return; ++ ++ rg->irq = irq_of_parse_and_map(np, 0); ++ if (!rg->irq) ++ return; ++ ++ rg->domain = irq_domain_add_linear(np, rg->chip.ngpio, ++ &irq_domain_ops, rg); ++ if (!rg->domain) { ++ dev_err(rg->chip.parent, "irq_domain_add_linear failed\n"); ++ return; ++ } ++ ++ irq_map[irq_map_count++] = rg->domain; ++ ++ rt_gpio_w32(rg, GPIO_REG_RENA, 0x0); ++ rt_gpio_w32(rg, GPIO_REG_FENA, 0x0); ++ ++ if (!atomic_read(&irq_refcount)) ++ irq_set_chained_handler(rg->irq, ralink_gpio_irq_handler); ++ atomic_inc(&irq_refcount); ++ ++ dev_info(rg->chip.parent, "registering %d irq handlers\n", rg->chip.ngpio); ++} ++ ++static int ralink_gpio_request(struct gpio_chip *chip, unsigned offset) ++{ ++ int gpio = chip->base + offset; ++ ++ return pinctrl_request_gpio(gpio); ++} ++ ++static void ralink_gpio_free(struct gpio_chip *chip, unsigned offset) ++{ ++ int gpio = chip->base + offset; ++ ++ pinctrl_free_gpio(gpio); ++} ++ ++static int ralink_gpio_probe(struct platform_device *pdev) ++{ ++ struct device_node *np = pdev->dev.of_node; ++ struct resource *res = platform_get_resource(pdev, IORESOURCE_MEM, 0); ++ struct ralink_gpio_chip *rg; ++ const __be32 *ngpio, *gpiobase; ++ ++ if (!res) { ++ dev_err(&pdev->dev, "failed to find resource\n"); ++ return -ENOMEM; ++ } ++ ++ rg = devm_kzalloc(&pdev->dev, ++ sizeof(struct ralink_gpio_chip), GFP_KERNEL); ++ if (!rg) ++ return -ENOMEM; ++ ++ rg->membase = devm_ioremap_resource(&pdev->dev, res); ++ if (!rg->membase) { ++ dev_err(&pdev->dev, "cannot remap I/O memory region\n"); ++ return -ENOMEM; ++ } ++ ++ if (of_property_read_u8_array(np, "ralink,register-map", ++ rg->regs, GPIO_REG_MAX)) { ++ dev_err(&pdev->dev, "failed to read register definition\n"); ++ return -EINVAL; ++ } ++ ++ ngpio = of_get_property(np, "ralink,nr-gpio", NULL); ++ if (!ngpio) { ++ dev_err(&pdev->dev, "failed to read number of pins\n"); ++ return -EINVAL; ++ } ++ ++ gpiobase = of_get_property(np, "ralink,gpio-base", NULL); ++ if (gpiobase) ++ rg->chip.base = be32_to_cpu(*gpiobase); ++ else ++ rg->chip.base = -1; ++ ++ spin_lock_init(&rg->lock); ++ ++ rg->chip.parent = &pdev->dev; ++ rg->chip.label = dev_name(&pdev->dev); ++ rg->chip.of_node = np; ++ rg->chip.ngpio = be32_to_cpu(*ngpio); ++ rg->chip.direction_input = ralink_gpio_direction_input; ++ rg->chip.direction_output = ralink_gpio_direction_output; ++ rg->chip.get = ralink_gpio_get; ++ rg->chip.set = ralink_gpio_set; ++ rg->chip.request = ralink_gpio_request; ++ rg->chip.to_irq = ralink_gpio_to_irq; ++ rg->chip.free = ralink_gpio_free; ++ ++ /* set polarity to low for all lines */ ++ rt_gpio_w32(rg, GPIO_REG_POL, 0); ++ ++ dev_info(&pdev->dev, "registering %d gpios\n", rg->chip.ngpio); ++ ++ ralink_gpio_irq_init(np, rg); ++ ++ return gpiochip_add(&rg->chip); ++} ++ ++static const struct of_device_id ralink_gpio_match[] = { ++ { .compatible = "ralink,rt2880-gpio" }, ++ {}, ++}; ++MODULE_DEVICE_TABLE(of, ralink_gpio_match); ++ ++static struct platform_driver ralink_gpio_driver = { ++ .probe = ralink_gpio_probe, ++ .driver = { ++ .name = "rt2880_gpio", ++ .owner = THIS_MODULE, ++ .of_match_table = ralink_gpio_match, ++ }, ++}; ++ ++static int __init ralink_gpio_init(void) ++{ ++ return platform_driver_register(&ralink_gpio_driver); ++} ++ ++subsys_initcall(ralink_gpio_init); diff --git a/target/linux/ramips/patches-5.4/0028-GPIO-ralink-add-mt7621-gpio-controller.patch b/target/linux/ramips/patches-5.4/0028-GPIO-ralink-add-mt7621-gpio-controller.patch new file mode 100644 index 0000000000..debeae2806 --- /dev/null +++ b/target/linux/ramips/patches-5.4/0028-GPIO-ralink-add-mt7621-gpio-controller.patch @@ -0,0 +1,405 @@ +From 61ac7d9b4228de8c332900902c2b93189b042eab Mon Sep 17 00:00:00 2001 +From: John Crispin +Date: Sun, 27 Jul 2014 11:00:32 +0100 +Subject: [PATCH 28/53] GPIO: ralink: add mt7621 gpio controller + +Signed-off-by: John Crispin +--- + arch/mips/Kconfig | 3 + + drivers/gpio/Kconfig | 6 + + drivers/gpio/Makefile | 1 + + drivers/gpio/gpio-mt7621.c | 354 ++++++++++++++++++++++++++++++++++++++++++++ + 4 files changed, 364 insertions(+) + create mode 100644 drivers/gpio/gpio-mt7621.c + +--- a/arch/mips/Kconfig ++++ b/arch/mips/Kconfig +@@ -631,6 +631,9 @@ config RALINK + select RESET_CONTROLLER + select PINCTRL + select PINCTRL_RT2880 ++ select ARCH_HAS_RESET_CONTROLLER ++ select RESET_CONTROLLER ++ select ARCH_REQUIRE_GPIOLIB + + config SGI_IP22 + bool "SGI IP22 (Indy/Indigo2)" +--- a/drivers/gpio/Kconfig ++++ b/drivers/gpio/Kconfig +@@ -298,6 +298,12 @@ config GPIO_MENZ127 + help + Say yes here to support the MEN 16Z127 GPIO Controller + ++config GPIO_MT7621 ++ bool "Mediatek GPIO Support" ++ depends on SOC_MT7620 || SOC_MT7621 ++ help ++ Say yes here to support the Mediatek SoC GPIO device ++ + config GPIO_MM_LANTIQ + bool "Lantiq Memory mapped GPIOs" + depends on LANTIQ && SOC_XWAY +--- a/drivers/gpio/Makefile ++++ b/drivers/gpio/Makefile +@@ -152,3 +152,4 @@ obj-$(CONFIG_GPIO_ZEVIO) += gpio-zevio.o + obj-$(CONFIG_GPIO_ZYNQ) += gpio-zynq.o + obj-$(CONFIG_GPIO_ZX) += gpio-zx.o + obj-$(CONFIG_GPIO_LOONGSON1) += gpio-loongson1.o ++obj-$(CONFIG_GPIO_MT7621) += gpio-mt7621.o +--- /dev/null ++++ b/drivers/gpio/gpio-mt7621.c +@@ -0,0 +1,354 @@ ++/* ++ * This program is free software; you can redistribute it and/or modify it ++ * under the terms of the GNU General Public License version 2 as published ++ * by the Free Software Foundation. ++ * ++ * Copyright (C) 2009-2011 Gabor Juhos ++ * Copyright (C) 2013 John Crispin ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#define MTK_MAX_BANK 3 ++#define MTK_BANK_WIDTH 32 ++ ++enum mediatek_gpio_reg { ++ GPIO_REG_CTRL = 0, ++ GPIO_REG_POL, ++ GPIO_REG_DATA, ++ GPIO_REG_DSET, ++ GPIO_REG_DCLR, ++ GPIO_REG_REDGE, ++ GPIO_REG_FEDGE, ++ GPIO_REG_HLVL, ++ GPIO_REG_LLVL, ++ GPIO_REG_STAT, ++ GPIO_REG_EDGE, ++}; ++ ++static void __iomem *mediatek_gpio_membase; ++static int mediatek_gpio_irq; ++static struct irq_domain *mediatek_gpio_irq_domain; ++static atomic_t irq_refcount = ATOMIC_INIT(0); ++ ++struct mtk_gc { ++ struct gpio_chip chip; ++ spinlock_t lock; ++ int bank; ++ u32 rising; ++ u32 falling; ++} *gc_map[MTK_MAX_BANK]; ++ ++static inline struct mtk_gc ++*to_mediatek_gpio(struct gpio_chip *chip) ++{ ++ struct mtk_gc *mgc; ++ ++ mgc = container_of(chip, struct mtk_gc, chip); ++ ++ return mgc; ++} ++ ++static inline void ++mtk_gpio_w32(struct mtk_gc *rg, u8 reg, u32 val) ++{ ++ iowrite32(val, mediatek_gpio_membase + (reg * 0x10) + (rg->bank * 0x4)); ++} ++ ++static inline u32 ++mtk_gpio_r32(struct mtk_gc *rg, u8 reg) ++{ ++ return ioread32(mediatek_gpio_membase + (reg * 0x10) + (rg->bank * 0x4)); ++} ++ ++static void ++mediatek_gpio_set(struct gpio_chip *chip, unsigned offset, int value) ++{ ++ struct mtk_gc *rg = to_mediatek_gpio(chip); ++ ++ mtk_gpio_w32(rg, (value) ? GPIO_REG_DSET : GPIO_REG_DCLR, BIT(offset)); ++} ++ ++static int ++mediatek_gpio_get(struct gpio_chip *chip, unsigned offset) ++{ ++ struct mtk_gc *rg = to_mediatek_gpio(chip); ++ ++ return !!(mtk_gpio_r32(rg, GPIO_REG_DATA) & BIT(offset)); ++} ++ ++static int ++mediatek_gpio_direction_input(struct gpio_chip *chip, unsigned offset) ++{ ++ struct mtk_gc *rg = to_mediatek_gpio(chip); ++ unsigned long flags; ++ u32 t; ++ ++ spin_lock_irqsave(&rg->lock, flags); ++ t = mtk_gpio_r32(rg, GPIO_REG_CTRL); ++ t &= ~BIT(offset); ++ mtk_gpio_w32(rg, GPIO_REG_CTRL, t); ++ spin_unlock_irqrestore(&rg->lock, flags); ++ ++ return 0; ++} ++ ++static int ++mediatek_gpio_direction_output(struct gpio_chip *chip, ++ unsigned offset, int value) ++{ ++ struct mtk_gc *rg = to_mediatek_gpio(chip); ++ unsigned long flags; ++ u32 t; ++ ++ spin_lock_irqsave(&rg->lock, flags); ++ t = mtk_gpio_r32(rg, GPIO_REG_CTRL); ++ t |= BIT(offset); ++ mtk_gpio_w32(rg, GPIO_REG_CTRL, t); ++ mediatek_gpio_set(chip, offset, value); ++ spin_unlock_irqrestore(&rg->lock, flags); ++ ++ return 0; ++} ++ ++static int ++mediatek_gpio_get_direction(struct gpio_chip *chip, unsigned offset) ++{ ++ struct mtk_gc *rg = to_mediatek_gpio(chip); ++ unsigned long flags; ++ u32 t; ++ ++ spin_lock_irqsave(&rg->lock, flags); ++ t = mtk_gpio_r32(rg, GPIO_REG_CTRL); ++ spin_unlock_irqrestore(&rg->lock, flags); ++ ++ if (t & BIT(offset)) ++ return 0; ++ ++ return 1; ++} ++ ++static int ++mediatek_gpio_to_irq(struct gpio_chip *chip, unsigned pin) ++{ ++ struct mtk_gc *rg = to_mediatek_gpio(chip); ++ ++ return irq_create_mapping(mediatek_gpio_irq_domain, pin + (rg->bank * MTK_BANK_WIDTH)); ++} ++ ++static int ++mediatek_gpio_bank_probe(struct platform_device *pdev, struct device_node *bank) ++{ ++ const __be32 *id = of_get_property(bank, "reg", NULL); ++ struct mtk_gc *rg = devm_kzalloc(&pdev->dev, ++ sizeof(struct mtk_gc), GFP_KERNEL); ++ ++ if (!rg || !id || be32_to_cpu(*id) > MTK_MAX_BANK) ++ return -ENOMEM; ++ ++ gc_map[be32_to_cpu(*id)] = rg; ++ ++ memset(rg, 0, sizeof(struct mtk_gc)); ++ ++ spin_lock_init(&rg->lock); ++ ++ rg->chip.parent = &pdev->dev; ++ rg->chip.label = dev_name(&pdev->dev); ++ rg->chip.of_node = bank; ++ rg->chip.base = MTK_BANK_WIDTH * be32_to_cpu(*id); ++ rg->chip.ngpio = MTK_BANK_WIDTH; ++ rg->chip.direction_input = mediatek_gpio_direction_input; ++ rg->chip.direction_output = mediatek_gpio_direction_output; ++ rg->chip.get_direction = mediatek_gpio_get_direction; ++ rg->chip.get = mediatek_gpio_get; ++ rg->chip.set = mediatek_gpio_set; ++ if (mediatek_gpio_irq_domain) ++ rg->chip.to_irq = mediatek_gpio_to_irq; ++ rg->bank = be32_to_cpu(*id); ++ ++ /* set polarity to low for all gpios */ ++ mtk_gpio_w32(rg, GPIO_REG_POL, 0); ++ ++ dev_info(&pdev->dev, "registering %d gpios\n", rg->chip.ngpio); ++ ++ return gpiochip_add(&rg->chip); ++} ++ ++static void ++mediatek_gpio_irq_handler(struct irq_desc *desc) ++{ ++ int i; ++ ++ for (i = 0; i < MTK_MAX_BANK; i++) { ++ struct mtk_gc *rg = gc_map[i]; ++ unsigned long pending; ++ int bit; ++ ++ if (!rg) ++ continue; ++ ++ pending = mtk_gpio_r32(rg, GPIO_REG_STAT); ++ ++ for_each_set_bit(bit, &pending, MTK_BANK_WIDTH) { ++ u32 map = irq_find_mapping(mediatek_gpio_irq_domain, (MTK_BANK_WIDTH * i) + bit); ++ ++ generic_handle_irq(map); ++ mtk_gpio_w32(rg, GPIO_REG_STAT, BIT(bit)); ++ } ++ } ++} ++ ++static void ++mediatek_gpio_irq_unmask(struct irq_data *d) ++{ ++ int pin = d->hwirq; ++ int bank = pin / 32; ++ struct mtk_gc *rg = gc_map[bank]; ++ unsigned long flags; ++ u32 rise, fall; ++ ++ if (!rg) ++ return; ++ ++ rise = mtk_gpio_r32(rg, GPIO_REG_REDGE); ++ fall = mtk_gpio_r32(rg, GPIO_REG_FEDGE); ++ ++ spin_lock_irqsave(&rg->lock, flags); ++ mtk_gpio_w32(rg, GPIO_REG_REDGE, rise | (BIT(d->hwirq) & rg->rising)); ++ mtk_gpio_w32(rg, GPIO_REG_FEDGE, fall | (BIT(d->hwirq) & rg->falling)); ++ spin_unlock_irqrestore(&rg->lock, flags); ++} ++ ++static void ++mediatek_gpio_irq_mask(struct irq_data *d) ++{ ++ int pin = d->hwirq; ++ int bank = pin / 32; ++ struct mtk_gc *rg = gc_map[bank]; ++ unsigned long flags; ++ u32 rise, fall; ++ ++ if (!rg) ++ return; ++ ++ rise = mtk_gpio_r32(rg, GPIO_REG_REDGE); ++ fall = mtk_gpio_r32(rg, GPIO_REG_FEDGE); ++ ++ spin_lock_irqsave(&rg->lock, flags); ++ mtk_gpio_w32(rg, GPIO_REG_FEDGE, fall & ~BIT(d->hwirq)); ++ mtk_gpio_w32(rg, GPIO_REG_REDGE, rise & ~BIT(d->hwirq)); ++ spin_unlock_irqrestore(&rg->lock, flags); ++} ++ ++static int ++mediatek_gpio_irq_type(struct irq_data *d, unsigned int type) ++{ ++ int pin = d->hwirq; ++ int bank = pin / 32; ++ struct mtk_gc *rg = gc_map[bank]; ++ u32 mask = BIT(d->hwirq); ++ ++ if (!rg) ++ return -1; ++ ++ if (type == IRQ_TYPE_PROBE) { ++ if ((rg->rising | rg->falling) & mask) ++ return 0; ++ ++ type = IRQ_TYPE_EDGE_RISING | IRQ_TYPE_EDGE_FALLING; ++ } ++ ++ if (type & IRQ_TYPE_EDGE_RISING) ++ rg->rising |= mask; ++ else ++ rg->rising &= ~mask; ++ ++ if (type & IRQ_TYPE_EDGE_FALLING) ++ rg->falling |= mask; ++ else ++ rg->falling &= ~mask; ++ ++ return 0; ++} ++ ++static struct irq_chip mediatek_gpio_irq_chip = { ++ .name = "GPIO", ++ .irq_unmask = mediatek_gpio_irq_unmask, ++ .irq_mask = mediatek_gpio_irq_mask, ++ .irq_mask_ack = mediatek_gpio_irq_mask, ++ .irq_set_type = mediatek_gpio_irq_type, ++}; ++ ++static int ++mediatek_gpio_gpio_map(struct irq_domain *d, unsigned int irq, irq_hw_number_t hw) ++{ ++ irq_set_chip_and_handler(irq, &mediatek_gpio_irq_chip, handle_level_irq); ++ irq_set_handler_data(irq, d); ++ ++ return 0; ++} ++ ++static const struct irq_domain_ops irq_domain_ops = { ++ .xlate = irq_domain_xlate_onecell, ++ .map = mediatek_gpio_gpio_map, ++}; ++ ++static int ++mediatek_gpio_probe(struct platform_device *pdev) ++{ ++ struct device_node *bank, *np = pdev->dev.of_node; ++ struct resource *res = platform_get_resource(pdev, IORESOURCE_MEM, 0); ++ ++ mediatek_gpio_membase = devm_ioremap_resource(&pdev->dev, res); ++ if (IS_ERR(mediatek_gpio_membase)) ++ return PTR_ERR(mediatek_gpio_membase); ++ ++ mediatek_gpio_irq = irq_of_parse_and_map(np, 0); ++ if (mediatek_gpio_irq) { ++ mediatek_gpio_irq_domain = irq_domain_add_linear(np, ++ MTK_MAX_BANK * MTK_BANK_WIDTH, ++ &irq_domain_ops, NULL); ++ if (!mediatek_gpio_irq_domain) ++ dev_err(&pdev->dev, "irq_domain_add_linear failed\n"); ++ } ++ ++ for_each_child_of_node(np, bank) ++ if (of_device_is_compatible(bank, "mtk,mt7621-gpio-bank")) ++ mediatek_gpio_bank_probe(pdev, bank); ++ ++ if (mediatek_gpio_irq_domain) ++ irq_set_chained_handler(mediatek_gpio_irq, mediatek_gpio_irq_handler); ++ ++ return 0; ++} ++ ++static const struct of_device_id mediatek_gpio_match[] = { ++ { .compatible = "mtk,mt7621-gpio" }, ++ {}, ++}; ++MODULE_DEVICE_TABLE(of, mediatek_gpio_match); ++ ++static struct platform_driver mediatek_gpio_driver = { ++ .probe = mediatek_gpio_probe, ++ .driver = { ++ .name = "mt7621_gpio", ++ .owner = THIS_MODULE, ++ .of_match_table = mediatek_gpio_match, ++ }, ++}; ++ ++static int __init ++mediatek_gpio_init(void) ++{ ++ return platform_driver_register(&mediatek_gpio_driver); ++} ++ ++subsys_initcall(mediatek_gpio_init); diff --git a/target/linux/ramips/patches-5.4/0029-gpio-ralink-Add-support-for-GPIO-as-interrupt-contro.patch b/target/linux/ramips/patches-5.4/0029-gpio-ralink-Add-support-for-GPIO-as-interrupt-contro.patch new file mode 100644 index 0000000000..8520ce32ff --- /dev/null +++ b/target/linux/ramips/patches-5.4/0029-gpio-ralink-Add-support-for-GPIO-as-interrupt-contro.patch @@ -0,0 +1,44 @@ +From 57fa7f2f4ef6f78ce1d30509c0d111aa3791b524 Mon Sep 17 00:00:00 2001 +From: Daniel Santos +Date: Sun, 4 Nov 2018 20:24:32 -0600 +Subject: gpio-ralink: Add support for GPIO as interrupt-controller + +Signed-off-by: Daniel Santos +--- + Documentation/devicetree/bindings/gpio/gpio-ralink.txt | 6 ++++++ + drivers/gpio/gpio-ralink.c | 2 +- + 2 files changed, 7 insertions(+), 1 deletion(-) + +--- a/Documentation/devicetree/bindings/gpio/gpio-ralink.txt ++++ b/Documentation/devicetree/bindings/gpio/gpio-ralink.txt +@@ -17,6 +17,9 @@ Required properties: + + Optional properties: + - ralink,gpio-base : Specify the GPIO chips base number ++- interrupt-controller : marks this as an interrupt controller ++- #interrupt-cells : a standard two-cell interrupt flag, see ++ interrupt-controller/interrupts.txt + + Example: + +@@ -28,6 +31,9 @@ Example: + + reg = <0x600 0x34>; + ++ interrupt-controller; ++ #interrupt-cells = <2>; ++ + interrupt-parent = <&intc>; + interrupts = <6>; + +--- a/drivers/gpio/gpio-ralink.c ++++ b/drivers/gpio/gpio-ralink.c +@@ -220,7 +220,7 @@ static int gpio_map(struct irq_domain *d + } + + static const struct irq_domain_ops irq_domain_ops = { +- .xlate = irq_domain_xlate_onecell, ++ .xlate = irq_domain_xlate_twocell, + .map = gpio_map, + }; + diff --git a/target/linux/ramips/patches-5.4/0031-uvc-add-iPassion-iP2970-support.patch b/target/linux/ramips/patches-5.4/0031-uvc-add-iPassion-iP2970-support.patch new file mode 100644 index 0000000000..7ed1a616f6 --- /dev/null +++ b/target/linux/ramips/patches-5.4/0031-uvc-add-iPassion-iP2970-support.patch @@ -0,0 +1,246 @@ +From 975e76214cd2516eb6cfff4c3eec581872645e88 Mon Sep 17 00:00:00 2001 +From: John Crispin +Date: Thu, 19 Sep 2013 01:50:59 +0200 +Subject: [PATCH 31/53] uvc: add iPassion iP2970 support + +Signed-off-by: John Crispin +--- + drivers/media/usb/uvc/uvc_driver.c | 12 +++ + drivers/media/usb/uvc/uvc_status.c | 2 + + drivers/media/usb/uvc/uvc_video.c | 147 ++++++++++++++++++++++++++++++++++++ + drivers/media/usb/uvc/uvcvideo.h | 5 +- + 4 files changed, 165 insertions(+), 1 deletion(-) + +--- a/drivers/media/usb/uvc/uvc_driver.c ++++ b/drivers/media/usb/uvc/uvc_driver.c +@@ -2749,6 +2749,18 @@ static const struct usb_device_id uvc_id + .bInterfaceSubClass = 1, + .bInterfaceProtocol = 0, + .driver_info = UVC_QUIRK_FORCE_Y8 }, ++ /* iPassion iP2970 */ ++ { .match_flags = USB_DEVICE_ID_MATCH_DEVICE ++ | USB_DEVICE_ID_MATCH_INT_INFO, ++ .idVendor = 0x1B3B, ++ .idProduct = 0x2970, ++ .bInterfaceClass = USB_CLASS_VIDEO, ++ .bInterfaceSubClass = 1, ++ .bInterfaceProtocol = 0, ++ .driver_info = UVC_QUIRK_PROBE_MINMAX ++ | UVC_QUIRK_STREAM_NO_FID ++ | UVC_QUIRK_MOTION ++ | UVC_QUIRK_SINGLE_ISO }, + /* Generic USB Video Class */ + { USB_INTERFACE_INFO(USB_CLASS_VIDEO, 1, UVC_PC_PROTOCOL_UNDEFINED) }, + { USB_INTERFACE_INFO(USB_CLASS_VIDEO, 1, UVC_PC_PROTOCOL_15) }, +--- a/drivers/media/usb/uvc/uvc_status.c ++++ b/drivers/media/usb/uvc/uvc_status.c +@@ -139,6 +139,7 @@ static void uvc_status_complete(struct u + switch (dev->status[0] & 0x0f) { + case UVC_STATUS_TYPE_CONTROL: + uvc_event_control(dev, dev->status, len); ++ dev->motion = 1; + break; + + case UVC_STATUS_TYPE_STREAMING: +@@ -182,6 +183,7 @@ int uvc_status_init(struct uvc_device *d + } + + pipe = usb_rcvintpipe(dev->udev, ep->desc.bEndpointAddress); ++ dev->motion = 0; + + /* For high-speed interrupt endpoints, the bInterval value is used as + * an exponent of two. Some developers forgot about it. +--- a/drivers/media/usb/uvc/uvc_video.c ++++ b/drivers/media/usb/uvc/uvc_video.c +@@ -21,6 +21,11 @@ + #include + #include + #include ++#include ++#include ++#include ++#include ++#include + + #include + +@@ -1101,9 +1106,149 @@ static void uvc_video_decode_data(struct + } + } + ++struct bh_priv { ++ unsigned long seen; ++}; ++ ++struct bh_event { ++ const char *name; ++ struct sk_buff *skb; ++ struct work_struct work; ++}; ++ ++#define BH_ERR(fmt, args...) printk(KERN_ERR "%s: " fmt, "webcam", ##args ) ++#define BH_DBG(fmt, args...) do {} while (0) ++#define BH_SKB_SIZE 2048 ++ ++extern u64 uevent_next_seqnum(void); ++static int seen = 0; ++ ++static int bh_event_add_var(struct bh_event *event, int argv, ++ const char *format, ...) ++{ ++ static char buf[128]; ++ char *s; ++ va_list args; ++ int len; ++ ++ if (argv) ++ return 0; ++ ++ va_start(args, format); ++ len = vsnprintf(buf, sizeof(buf), format, args); ++ va_end(args); ++ ++ if (len >= sizeof(buf)) { ++ BH_ERR("buffer size too small\n"); ++ WARN_ON(1); ++ return -ENOMEM; ++ } ++ ++ s = skb_put(event->skb, len + 1); ++ strcpy(s, buf); ++ ++ BH_DBG("added variable '%s'\n", s); ++ ++ return 0; ++} ++ ++static int motion_hotplug_fill_event(struct bh_event *event) ++{ ++ int s = jiffies; ++ int ret; ++ ++ if (!seen) ++ seen = jiffies; ++ ++ ret = bh_event_add_var(event, 0, "HOME=%s", "/"); ++ if (ret) ++ return ret; ++ ++ ret = bh_event_add_var(event, 0, "PATH=%s", ++ "/sbin:/bin:/usr/sbin:/usr/bin"); ++ if (ret) ++ return ret; ++ ++ ret = bh_event_add_var(event, 0, "SUBSYSTEM=usb"); ++ if (ret) ++ return ret; ++ ++ ret = bh_event_add_var(event, 0, "ACTION=motion"); ++ if (ret) ++ return ret; ++ ++ ret = bh_event_add_var(event, 0, "SEEN=%d", s - seen); ++ if (ret) ++ return ret; ++ seen = s; ++ ++ ret = bh_event_add_var(event, 0, "SEQNUM=%llu", uevent_next_seqnum()); ++ ++ return ret; ++} ++ ++static void motion_hotplug_work(struct work_struct *work) ++{ ++ struct bh_event *event = container_of(work, struct bh_event, work); ++ int ret = 0; ++ ++ event->skb = alloc_skb(BH_SKB_SIZE, GFP_KERNEL); ++ if (!event->skb) ++ goto out_free_event; ++ ++ ret = bh_event_add_var(event, 0, "%s@", "add"); ++ if (ret) ++ goto out_free_skb; ++ ++ ret = motion_hotplug_fill_event(event); ++ if (ret) ++ goto out_free_skb; ++ ++ NETLINK_CB(event->skb).dst_group = 1; ++ broadcast_uevent(event->skb, 0, 1, GFP_KERNEL); ++ ++out_free_skb: ++ if (ret) { ++ BH_ERR("work error %d\n", ret); ++ kfree_skb(event->skb); ++ } ++out_free_event: ++ kfree(event); ++} ++ ++static int motion_hotplug_create_event(void) ++{ ++ struct bh_event *event; ++ ++ event = kzalloc(sizeof(*event), GFP_KERNEL); ++ if (!event) ++ return -ENOMEM; ++ ++ event->name = "motion"; ++ ++ INIT_WORK(&event->work, (void *)(void *)motion_hotplug_work); ++ schedule_work(&event->work); ++ ++ return 0; ++} ++ ++#define MOTION_FLAG_OFFSET 4 + static void uvc_video_decode_end(struct uvc_streaming *stream, + struct uvc_buffer *buf, const __u8 *data, int len) + { ++ if ((stream->dev->quirks & UVC_QUIRK_MOTION) && ++ (data[len - 2] == 0xff) && (data[len - 1] == 0xd9)) { ++ u8 *mem; ++ buf->state = UVC_BUF_STATE_READY; ++ mem = (u8 *) (buf->mem + MOTION_FLAG_OFFSET); ++ if ( stream->dev->motion ) { ++ stream->dev->motion = 0; ++ motion_hotplug_create_event(); ++ } else { ++ *mem &= 0x7f; ++ } ++ } ++ + /* Mark the buffer as done if the EOF marker is set. */ + if (data[1] & UVC_STREAM_EOF && buf->bytesused != 0) { + uvc_trace(UVC_TRACE_FRAME, "Frame complete (EOF found).\n"); +@@ -1518,6 +1663,8 @@ static int uvc_init_video_isoc(struct uv + if (npackets == 0) + return -ENOMEM; + ++ if (stream->dev->quirks & UVC_QUIRK_SINGLE_ISO) ++ npackets = 1; + size = npackets * psize; + + for (i = 0; i < UVC_URBS; ++i) { +--- a/drivers/media/usb/uvc/uvcvideo.h ++++ b/drivers/media/usb/uvc/uvcvideo.h +@@ -186,7 +186,9 @@ + #define UVC_QUIRK_RESTRICT_FRAME_RATE 0x00000200 + #define UVC_QUIRK_RESTORE_CTRLS_ON_INIT 0x00000400 + #define UVC_QUIRK_FORCE_Y8 0x00000800 +- ++#define UVC_QUIRK_MOTION 0x00001000 ++#define UVC_QUIRK_SINGLE_ISO 0x00002000 ++ + /* Format flags */ + #define UVC_FMT_FLAG_COMPRESSED 0x00000001 + #define UVC_FMT_FLAG_STREAM 0x00000002 +@@ -584,6 +586,7 @@ struct uvc_device { + __u8 *status; + struct input_dev *input; + char input_phys[64]; ++ int motion; + }; + + enum uvc_handle_state { diff --git a/target/linux/ramips/patches-5.4/0032-USB-dwc2-add-device_reset.patch b/target/linux/ramips/patches-5.4/0032-USB-dwc2-add-device_reset.patch new file mode 100644 index 0000000000..c04e2db661 --- /dev/null +++ b/target/linux/ramips/patches-5.4/0032-USB-dwc2-add-device_reset.patch @@ -0,0 +1,29 @@ +From a758e0870c6d1e4b0272f6e7f9efa9face5534bb Mon Sep 17 00:00:00 2001 +From: John Crispin +Date: Sun, 27 Jul 2014 09:49:07 +0100 +Subject: [PATCH 32/53] USB: dwc2: add device_reset() + +Signed-off-by: John Crispin +--- + drivers/usb/dwc2/hcd.c | 3 +++ + 1 file changed, 3 insertions(+) + +--- a/drivers/usb/dwc2/hcd.c ++++ b/drivers/usb/dwc2/hcd.c +@@ -48,6 +48,7 @@ + #include + #include + #include ++#include + + #include + #include +@@ -5215,6 +5216,8 @@ int dwc2_hcd_init(struct dwc2_hsotg *hso + + retval = -ENOMEM; + ++ device_reset(hsotg->dev); ++ + hcfg = dwc2_readl(hsotg->regs + HCFG); + dev_dbg(hsotg->dev, "hcfg=%08x\n", hcfg); + diff --git a/target/linux/ramips/patches-5.4/0034-NET-multi-phy-support.patch b/target/linux/ramips/patches-5.4/0034-NET-multi-phy-support.patch new file mode 100644 index 0000000000..5536e3f61c --- /dev/null +++ b/target/linux/ramips/patches-5.4/0034-NET-multi-phy-support.patch @@ -0,0 +1,59 @@ +From 0b6eb1e68290243d439ee330ea8d0b239a5aec69 Mon Sep 17 00:00:00 2001 +From: John Crispin +Date: Sun, 27 Jul 2014 09:38:50 +0100 +Subject: [PATCH 34/53] NET: multi phy support + +Signed-off-by: John Crispin +--- + drivers/net/phy/phy.c | 9 ++++++--- + include/linux/phy.h | 1 + + 2 files changed, 7 insertions(+), 3 deletions(-) + +--- a/drivers/net/phy/phy.c ++++ b/drivers/net/phy/phy.c +@@ -913,7 +913,10 @@ void phy_state_machine(struct work_struc + /* If the link is down, give up on negotiation for now */ + if (!phydev->link) { + phydev->state = PHY_NOLINK; +- phy_link_down(phydev, true); ++ if (!phydev->no_auto_carrier_off) ++ phy_link_down(phydev, true); ++ else ++ phy_link_down(phydev, false); + break; + } + +@@ -1000,7 +1003,10 @@ void phy_state_machine(struct work_struc + phy_link_up(phydev); + } else { + phydev->state = PHY_NOLINK; +- phy_link_down(phydev, true); ++ if (!phydev->no_auto_carrier_off) ++ phy_link_down(phydev, true); ++ else ++ phy_link_down(phydev, false); + } + + if (phy_interrupt_is_valid(phydev)) +@@ -1010,7 +1016,10 @@ void phy_state_machine(struct work_struc + case PHY_HALTED: + if (phydev->link) { + phydev->link = 0; +- phy_link_down(phydev, true); ++ if (!phydev->no_auto_carrier_off) ++ phy_link_down(phydev, true); ++ else ++ phy_link_down(phydev, false); + do_suspend = true; + } + break; +--- a/include/linux/phy.h ++++ b/include/linux/phy.h +@@ -412,6 +412,7 @@ struct phy_device { + bool suspended; + bool sysfs_links; + bool loopback_enabled; ++ bool no_auto_carrier_off; + + enum phy_state state; + diff --git a/target/linux/ramips/patches-5.4/0037-mtd-cfi-cmdset-0002-force-word-write.patch b/target/linux/ramips/patches-5.4/0037-mtd-cfi-cmdset-0002-force-word-write.patch new file mode 100644 index 0000000000..478af4cbc9 --- /dev/null +++ b/target/linux/ramips/patches-5.4/0037-mtd-cfi-cmdset-0002-force-word-write.patch @@ -0,0 +1,70 @@ +From ee9081b2726a5ca8cde5497afdc5425e21ff8f8b Mon Sep 17 00:00:00 2001 +From: John Crispin +Date: Mon, 15 Jul 2013 00:39:21 +0200 +Subject: [PATCH 37/53] mtd: cfi cmdset 0002 force word write + +--- + drivers/mtd/chips/cfi_cmdset_0002.c | 9 +++++++-- + 1 file changed, 7 insertions(+), 2 deletions(-) + +--- a/drivers/mtd/chips/cfi_cmdset_0002.c ++++ b/drivers/mtd/chips/cfi_cmdset_0002.c +@@ -40,7 +40,7 @@ + #include + + #define AMD_BOOTLOC_BUG +-#define FORCE_WORD_WRITE 0 ++#define FORCE_WORD_WRITE 1 + + #define MAX_RETRIES 3 + +@@ -51,7 +51,9 @@ + + static int cfi_amdstd_read (struct mtd_info *, loff_t, size_t, size_t *, u_char *); + static int cfi_amdstd_write_words(struct mtd_info *, loff_t, size_t, size_t *, const u_char *); ++#if !FORCE_WORD_WRITE + static int cfi_amdstd_write_buffers(struct mtd_info *, loff_t, size_t, size_t *, const u_char *); ++#endif + static int cfi_amdstd_erase_chip(struct mtd_info *, struct erase_info *); + static int cfi_amdstd_erase_varsize(struct mtd_info *, struct erase_info *); + static void cfi_amdstd_sync (struct mtd_info *); +@@ -202,6 +204,7 @@ static void fixup_amd_bootblock(struct m + } + #endif + ++#if !FORCE_WORD_WRITE + static void fixup_use_write_buffers(struct mtd_info *mtd) + { + struct map_info *map = mtd->priv; +@@ -211,6 +214,7 @@ static void fixup_use_write_buffers(stru + mtd->_write = cfi_amdstd_write_buffers; + } + } ++#endif /* !FORCE_WORD_WRITE */ + + /* Atmel chips don't use the same PRI format as AMD chips */ + static void fixup_convert_atmel_pri(struct mtd_info *mtd) +@@ -1798,6 +1802,7 @@ static int cfi_amdstd_write_words(struct + /* + * FIXME: interleaved mode not tested, and probably not supported! + */ ++#if !FORCE_WORD_WRITE + static int __xipram do_write_buffer(struct map_info *map, struct flchip *chip, + unsigned long adr, const u_char *buf, + int len) +@@ -1926,7 +1931,6 @@ static int __xipram do_write_buffer(stru + return ret; + } + +- + static int cfi_amdstd_write_buffers(struct mtd_info *mtd, loff_t to, size_t len, + size_t *retlen, const u_char *buf) + { +@@ -2001,6 +2005,7 @@ static int cfi_amdstd_write_buffers(stru + + return 0; + } ++#endif /* !FORCE_WORD_WRITE */ + + /* + * Wait for the flash chip to become ready to write data diff --git a/target/linux/ramips/patches-5.4/0038-Revert-mtd-nand-Remove-unused-chip-write_page-hook.patch b/target/linux/ramips/patches-5.4/0038-Revert-mtd-nand-Remove-unused-chip-write_page-hook.patch new file mode 100644 index 0000000000..4758f18558 --- /dev/null +++ b/target/linux/ramips/patches-5.4/0038-Revert-mtd-nand-Remove-unused-chip-write_page-hook.patch @@ -0,0 +1,67 @@ +From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= +Subject: [PATCH] Revert "mtd: nand: Remove unused chip->write_page() hook" +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +This reverts commit f107d7a43923a83d837b3ea3c7b7de58cd014bbd. + +OpenWrt's downstream driver mtk_nand2 still uses that callback. + +Signed-off-by: Rafał Miłecki +--- + +--- a/drivers/mtd/nand/nand_base.c ++++ b/drivers/mtd/nand/nand_base.c +@@ -2577,7 +2577,7 @@ static int nand_write_page_syndrome(stru + } + + /** +- * nand_write_page - write one page ++ * nand_write_page - [REPLACEABLE] write one page + * @mtd: MTD device structure + * @chip: NAND chip descriptor + * @offset: address offset within the page +@@ -2761,9 +2761,9 @@ static int nand_do_write_ops(struct mtd_ + memset(chip->oob_poi, 0xff, mtd->oobsize); + } + +- ret = nand_write_page(mtd, chip, column, bytes, wbuf, +- oob_required, page, +- (ops->mode == MTD_OPS_RAW)); ++ ret = chip->write_page(mtd, chip, column, bytes, wbuf, ++ oob_required, page, ++ (ops->mode == MTD_OPS_RAW)); + if (ret) + break; + +@@ -4719,6 +4719,9 @@ int nand_scan_tail(struct mtd_info *mtd) + } + } + ++ if (!chip->write_page) ++ chip->write_page = nand_write_page; ++ + /* + * Check ECC mode, default to software if 3byte/512byte hardware ECC is + * selected and we have 256 byte pagesize fallback to software ECC +--- a/include/linux/mtd/rawnand.h ++++ b/include/linux/mtd/rawnand.h +@@ -862,6 +862,7 @@ struct nand_manufacturer_ops { + * structure which is shared among multiple independent + * devices. + * @priv: [OPTIONAL] pointer to private chip data ++ * @write_page: [REPLACEABLE] High-level page write function + * @manufacturer: [INTERN] Contains manufacturer information + */ + +@@ -885,6 +886,9 @@ struct nand_chip { + int(*waitfunc)(struct mtd_info *mtd, struct nand_chip *this); + int (*erase)(struct mtd_info *mtd, int page); + int (*scan_bbt)(struct mtd_info *mtd); ++ int (*write_page)(struct mtd_info *mtd, struct nand_chip *chip, ++ uint32_t offset, int data_len, const uint8_t *buf, ++ int oob_required, int page, int raw); + int (*onfi_set_features)(struct mtd_info *mtd, struct nand_chip *chip, + int feature_addr, uint8_t *subfeature_para); + int (*onfi_get_features)(struct mtd_info *mtd, struct nand_chip *chip, diff --git a/target/linux/ramips/patches-5.4/0039-mtd-add-mt7621-nand-support.patch b/target/linux/ramips/patches-5.4/0039-mtd-add-mt7621-nand-support.patch new file mode 100644 index 0000000000..3c6a59b863 --- /dev/null +++ b/target/linux/ramips/patches-5.4/0039-mtd-add-mt7621-nand-support.patch @@ -0,0 +1,4437 @@ +From 0e1c4e3c97b83b4e7da65b1c56f0a7d40736ac53 Mon Sep 17 00:00:00 2001 +From: John Crispin +Date: Sun, 27 Jul 2014 11:05:17 +0100 +Subject: [PATCH 39/53] mtd: add mt7621 nand support + +Signed-off-by: John Crispin +--- + drivers/mtd/nand/Kconfig | 6 + + drivers/mtd/nand/Makefile | 1 + + drivers/mtd/nand/bmt.c | 750 ++++++++++++ + drivers/mtd/nand/bmt.h | 80 ++ + drivers/mtd/nand/dev-nand.c | 63 + + drivers/mtd/nand/mt6575_typedefs.h | 340 ++++++ + drivers/mtd/nand/mtk_nand2.c | 2304 +++++++++++++++++++++++++++++++++++ + drivers/mtd/nand/mtk_nand2.h | 452 +++++++ + drivers/mtd/nand/nand_base.c | 6 +- + drivers/mtd/nand/nand_def.h | 123 ++ + drivers/mtd/nand/nand_device_list.h | 55 + + drivers/mtd/nand/partition.h | 115 ++ + 13 files changed, 4311 insertions(+), 3 deletions(-) + create mode 100644 drivers/mtd/nand/bmt.c + create mode 100644 drivers/mtd/nand/bmt.h + create mode 100644 drivers/mtd/nand/dev-nand.c + create mode 100644 drivers/mtd/nand/mt6575_typedefs.h + create mode 100644 drivers/mtd/nand/mtk_nand2.c + create mode 100644 drivers/mtd/nand/mtk_nand2.h + create mode 100644 drivers/mtd/nand/nand_def.h + create mode 100644 drivers/mtd/nand/nand_device_list.h + create mode 100644 drivers/mtd/nand/partition.h + +--- a/drivers/mtd/nand/Kconfig ++++ b/drivers/mtd/nand/Kconfig +@@ -563,4 +563,10 @@ config MTD_NAND_MTK + Enables support for NAND controller on MTK SoCs. + This controller is found on mt27xx, mt81xx, mt65xx SoCs. + ++config MTK_MTD_NAND ++ tristate "Support for MTK SoC NAND controller" ++ depends on SOC_MT7621 ++ select MTD_NAND_IDS ++ select MTD_NAND_ECC ++ + endif # MTD_NAND +--- a/drivers/mtd/nand/Makefile ++++ b/drivers/mtd/nand/Makefile +@@ -60,6 +60,7 @@ obj-$(CONFIG_MTD_NAND_HISI504) + + obj-$(CONFIG_MTD_NAND_BRCMNAND) += brcmnand/ + obj-$(CONFIG_MTD_NAND_QCOM) += qcom_nandc.o + obj-$(CONFIG_MTD_NAND_MTK) += mtk_nand.o mtk_ecc.o ++obj-$(CONFIG_MTK_MTD_NAND) += mtk_nand2.o bmt.o + + nand-objs := nand_base.o nand_bbt.o nand_timings.o nand_ids.o + nand-objs += nand_amd.o +--- /dev/null ++++ b/drivers/mtd/nand/bmt.c +@@ -0,0 +1,750 @@ ++#include "bmt.h" ++ ++typedef struct ++{ ++ char signature[3]; ++ u8 version; ++ u8 bad_count; // bad block count in pool ++ u8 mapped_count; // mapped block count in pool ++ u8 checksum; ++ u8 reseverd[13]; ++} phys_bmt_header; ++ ++typedef struct ++{ ++ phys_bmt_header header; ++ bmt_entry table[MAX_BMT_SIZE]; ++} phys_bmt_struct; ++ ++typedef struct ++{ ++ char signature[3]; ++} bmt_oob_data; ++ ++static char MAIN_SIGNATURE[] = "BMT"; ++static char OOB_SIGNATURE[] = "bmt"; ++#define SIGNATURE_SIZE (3) ++ ++#define MAX_DAT_SIZE 0x1000 ++#define MAX_OOB_SIZE 0x80 ++ ++static struct mtd_info *mtd_bmt; ++static struct nand_chip *nand_chip_bmt; ++#define BLOCK_SIZE_BMT (1 << nand_chip_bmt->phys_erase_shift) ++#define PAGE_SIZE_BMT (1 << nand_chip_bmt->page_shift) ++ ++#define OFFSET(block) ((block) * BLOCK_SIZE_BMT) ++#define PAGE_ADDR(block) ((block) * BLOCK_SIZE_BMT / PAGE_SIZE_BMT) ++ ++/********************************************************************* ++* Flash is splited into 2 parts, system part is for normal system * ++* system usage, size is system_block_count, another is replace pool * ++* +-------------------------------------------------+ * ++* | system_block_count | bmt_block_count | * ++* +-------------------------------------------------+ * ++*********************************************************************/ ++static u32 total_block_count; // block number in flash ++static u32 system_block_count; ++static int bmt_block_count; // bmt table size ++// static int bmt_count; // block used in bmt ++static int page_per_block; // page per count ++ ++static u32 bmt_block_index; // bmt block index ++static bmt_struct bmt; // dynamic created global bmt table ++ ++static u8 dat_buf[MAX_DAT_SIZE]; ++static u8 oob_buf[MAX_OOB_SIZE]; ++static bool pool_erased; ++ ++/*************************************************************** ++* ++* Interface adaptor for preloader/uboot/kernel ++* These interfaces operate on physical address, read/write ++* physical data. ++* ++***************************************************************/ ++int nand_read_page_bmt(u32 page, u8 * dat, u8 * oob) ++{ ++ return mtk_nand_exec_read_page(mtd_bmt, page, PAGE_SIZE_BMT, dat, oob); ++} ++ ++bool nand_block_bad_bmt(u32 offset) ++{ ++ return mtk_nand_block_bad_hw(mtd_bmt, offset); ++} ++ ++bool nand_erase_bmt(u32 offset) ++{ ++ int status; ++ if (offset < 0x20000) ++ { ++ MSG(INIT, "erase offset: 0x%x\n", offset); ++ } ++ ++ status = mtk_nand_erase_hw(mtd_bmt, offset / PAGE_SIZE_BMT); // as nand_chip structure doesn't have a erase function defined ++ if (status & NAND_STATUS_FAIL) ++ return false; ++ else ++ return true; ++} ++ ++int mark_block_bad_bmt(u32 offset) ++{ ++ return mtk_nand_block_markbad_hw(mtd_bmt, offset); //mark_block_bad_hw(offset); ++} ++ ++bool nand_write_page_bmt(u32 page, u8 * dat, u8 * oob) ++{ ++ if (mtk_nand_exec_write_page(mtd_bmt, page, PAGE_SIZE_BMT, dat, oob)) ++ return false; ++ else ++ return true; ++} ++ ++/*************************************************************** ++* * ++* static internal function * ++* * ++***************************************************************/ ++static void dump_bmt_info(bmt_struct * bmt) ++{ ++ int i; ++ ++ MSG(INIT, "BMT v%d. total %d mapping:\n", bmt->version, bmt->mapped_count); ++ for (i = 0; i < bmt->mapped_count; i++) ++ { ++ MSG(INIT, "\t0x%x -> 0x%x\n", bmt->table[i].bad_index, bmt->table[i].mapped_index); ++ } ++} ++ ++static bool match_bmt_signature(u8 * dat, u8 * oob) ++{ ++ ++ if (memcmp(dat + MAIN_SIGNATURE_OFFSET, MAIN_SIGNATURE, SIGNATURE_SIZE)) ++ { ++ return false; ++ } ++ ++ if (memcmp(oob + OOB_SIGNATURE_OFFSET, OOB_SIGNATURE, SIGNATURE_SIZE)) ++ { ++ MSG(INIT, "main signature match, oob signature doesn't match, but ignore\n"); ++ } ++ return true; ++} ++ ++static u8 cal_bmt_checksum(phys_bmt_struct * phys_table, int bmt_size) ++{ ++ int i; ++ u8 checksum = 0; ++ u8 *dat = (u8 *) phys_table; ++ ++ checksum += phys_table->header.version; ++ checksum += phys_table->header.mapped_count; ++ ++ dat += sizeof(phys_bmt_header); ++ for (i = 0; i < bmt_size * sizeof(bmt_entry); i++) ++ { ++ checksum += dat[i]; ++ } ++ ++ return checksum; ++} ++ ++ ++static int is_block_mapped(int index) ++{ ++ int i; ++ for (i = 0; i < bmt.mapped_count; i++) ++ { ++ if (index == bmt.table[i].mapped_index) ++ return i; ++ } ++ return -1; ++} ++ ++static bool is_page_used(u8 * dat, u8 * oob) ++{ ++ return ((oob[OOB_INDEX_OFFSET] != 0xFF) || (oob[OOB_INDEX_OFFSET + 1] != 0xFF)); ++} ++ ++static bool valid_bmt_data(phys_bmt_struct * phys_table) ++{ ++ int i; ++ u8 checksum = cal_bmt_checksum(phys_table, bmt_block_count); ++ ++ // checksum correct? ++ if (phys_table->header.checksum != checksum) ++ { ++ MSG(INIT, "BMT Data checksum error: %x %x\n", phys_table->header.checksum, checksum); ++ return false; ++ } ++ ++ MSG(INIT, "BMT Checksum is: 0x%x\n", phys_table->header.checksum); ++ ++ // block index correct? ++ for (i = 0; i < phys_table->header.mapped_count; i++) ++ { ++ if (phys_table->table[i].bad_index >= total_block_count || phys_table->table[i].mapped_index >= total_block_count || phys_table->table[i].mapped_index < system_block_count) ++ { ++ MSG(INIT, "index error: bad_index: %d, mapped_index: %d\n", phys_table->table[i].bad_index, phys_table->table[i].mapped_index); ++ return false; ++ } ++ } ++ ++ // pass check, valid bmt. ++ MSG(INIT, "Valid BMT, version v%d\n", phys_table->header.version); ++ return true; ++} ++ ++static void fill_nand_bmt_buffer(bmt_struct * bmt, u8 * dat, u8 * oob) ++{ ++ phys_bmt_struct phys_bmt; ++ ++ dump_bmt_info(bmt); ++ ++ // fill phys_bmt_struct structure with bmt_struct ++ memset(&phys_bmt, 0xFF, sizeof(phys_bmt)); ++ ++ memcpy(phys_bmt.header.signature, MAIN_SIGNATURE, SIGNATURE_SIZE); ++ phys_bmt.header.version = BMT_VERSION; ++ // phys_bmt.header.bad_count = bmt->bad_count; ++ phys_bmt.header.mapped_count = bmt->mapped_count; ++ memcpy(phys_bmt.table, bmt->table, sizeof(bmt_entry) * bmt_block_count); ++ ++ phys_bmt.header.checksum = cal_bmt_checksum(&phys_bmt, bmt_block_count); ++ ++ memcpy(dat + MAIN_SIGNATURE_OFFSET, &phys_bmt, sizeof(phys_bmt)); ++ memcpy(oob + OOB_SIGNATURE_OFFSET, OOB_SIGNATURE, SIGNATURE_SIZE); ++} ++ ++// return valid index if found BMT, else return 0 ++static int load_bmt_data(int start, int pool_size) ++{ ++ int bmt_index = start + pool_size - 1; // find from the end ++ phys_bmt_struct phys_table; ++ int i; ++ ++ MSG(INIT, "[%s]: begin to search BMT from block 0x%x\n", __FUNCTION__, bmt_index); ++ ++ for (bmt_index = start + pool_size - 1; bmt_index >= start; bmt_index--) ++ { ++ if (nand_block_bad_bmt(OFFSET(bmt_index))) ++ { ++ MSG(INIT, "Skip bad block: %d\n", bmt_index); ++ continue; ++ } ++ ++ if (!nand_read_page_bmt(PAGE_ADDR(bmt_index), dat_buf, oob_buf)) ++ { ++ MSG(INIT, "Error found when read block %d\n", bmt_index); ++ continue; ++ } ++ ++ if (!match_bmt_signature(dat_buf, oob_buf)) ++ { ++ continue; ++ } ++ ++ MSG(INIT, "Match bmt signature @ block: 0x%x\n", bmt_index); ++ ++ memcpy(&phys_table, dat_buf + MAIN_SIGNATURE_OFFSET, sizeof(phys_table)); ++ ++ if (!valid_bmt_data(&phys_table)) ++ { ++ MSG(INIT, "BMT data is not correct %d\n", bmt_index); ++ continue; ++ } else ++ { ++ bmt.mapped_count = phys_table.header.mapped_count; ++ bmt.version = phys_table.header.version; ++ // bmt.bad_count = phys_table.header.bad_count; ++ memcpy(bmt.table, phys_table.table, bmt.mapped_count * sizeof(bmt_entry)); ++ ++ MSG(INIT, "bmt found at block: %d, mapped block: %d\n", bmt_index, bmt.mapped_count); ++ ++ for (i = 0; i < bmt.mapped_count; i++) ++ { ++ if (!nand_block_bad_bmt(OFFSET(bmt.table[i].bad_index))) ++ { ++ MSG(INIT, "block 0x%x is not mark bad, should be power lost last time\n", bmt.table[i].bad_index); ++ mark_block_bad_bmt(OFFSET(bmt.table[i].bad_index)); ++ } ++ } ++ ++ return bmt_index; ++ } ++ } ++ ++ MSG(INIT, "bmt block not found!\n"); ++ return 0; ++} ++ ++/************************************************************************* ++* Find an available block and erase. * ++* start_from_end: if true, find available block from end of flash. * ++* else, find from the beginning of the pool * ++* need_erase: if true, all unmapped blocks in the pool will be erased * ++*************************************************************************/ ++static int find_available_block(bool start_from_end) ++{ ++ int i; // , j; ++ int block = system_block_count; ++ int direction; ++ // int avail_index = 0; ++ MSG(INIT, "Try to find_available_block, pool_erase: %d\n", pool_erased); ++ ++ // erase all un-mapped blocks in pool when finding avaliable block ++ if (!pool_erased) ++ { ++ MSG(INIT, "Erase all un-mapped blocks in pool\n"); ++ for (i = 0; i < bmt_block_count; i++) ++ { ++ if (block == bmt_block_index) ++ { ++ MSG(INIT, "Skip bmt block 0x%x\n", block); ++ continue; ++ } ++ ++ if (nand_block_bad_bmt(OFFSET(block + i))) ++ { ++ MSG(INIT, "Skip bad block 0x%x\n", block + i); ++ continue; ++ } ++//if(block==4095) ++//{ ++// continue; ++//} ++ ++ if (is_block_mapped(block + i) >= 0) ++ { ++ MSG(INIT, "Skip mapped block 0x%x\n", block + i); ++ continue; ++ } ++ ++ if (!nand_erase_bmt(OFFSET(block + i))) ++ { ++ MSG(INIT, "Erase block 0x%x failed\n", block + i); ++ mark_block_bad_bmt(OFFSET(block + i)); ++ } ++ } ++ ++ pool_erased = 1; ++ } ++ ++ if (start_from_end) ++ { ++ block = total_block_count - 1; ++ direction = -1; ++ } else ++ { ++ block = system_block_count; ++ direction = 1; ++ } ++ ++ for (i = 0; i < bmt_block_count; i++, block += direction) ++ { ++ if (block == bmt_block_index) ++ { ++ MSG(INIT, "Skip bmt block 0x%x\n", block); ++ continue; ++ } ++ ++ if (nand_block_bad_bmt(OFFSET(block))) ++ { ++ MSG(INIT, "Skip bad block 0x%x\n", block); ++ continue; ++ } ++ ++ if (is_block_mapped(block) >= 0) ++ { ++ MSG(INIT, "Skip mapped block 0x%x\n", block); ++ continue; ++ } ++ ++ MSG(INIT, "Find block 0x%x available\n", block); ++ return block; ++ } ++ ++ return 0; ++} ++ ++static unsigned short get_bad_index_from_oob(u8 * oob_buf) ++{ ++ unsigned short index; ++ memcpy(&index, oob_buf + OOB_INDEX_OFFSET, OOB_INDEX_SIZE); ++ ++ return index; ++} ++ ++void set_bad_index_to_oob(u8 * oob, u16 index) ++{ ++ memcpy(oob + OOB_INDEX_OFFSET, &index, sizeof(index)); ++} ++ ++static int migrate_from_bad(int offset, u8 * write_dat, u8 * write_oob) ++{ ++ int page; ++ int error_block = offset / BLOCK_SIZE_BMT; ++ int error_page = (offset / PAGE_SIZE_BMT) % page_per_block; ++ int to_index; ++ ++ memcpy(oob_buf, write_oob, MAX_OOB_SIZE); ++ ++ to_index = find_available_block(false); ++ ++ if (!to_index) ++ { ++ MSG(INIT, "Cannot find an available block for BMT\n"); ++ return 0; ++ } ++ ++ { // migrate error page first ++ MSG(INIT, "Write error page: 0x%x\n", error_page); ++ if (!write_dat) ++ { ++ nand_read_page_bmt(PAGE_ADDR(error_block) + error_page, dat_buf, NULL); ++ write_dat = dat_buf; ++ } ++ // memcpy(oob_buf, write_oob, MAX_OOB_SIZE); ++ ++ if (error_block < system_block_count) ++ set_bad_index_to_oob(oob_buf, error_block); // if error_block is already a mapped block, original mapping index is in OOB. ++ ++ if (!nand_write_page_bmt(PAGE_ADDR(to_index) + error_page, write_dat, oob_buf)) ++ { ++ MSG(INIT, "Write to page 0x%x fail\n", PAGE_ADDR(to_index) + error_page); ++ mark_block_bad_bmt(to_index); ++ return migrate_from_bad(offset, write_dat, write_oob); ++ } ++ } ++ ++ for (page = 0; page < page_per_block; page++) ++ { ++ if (page != error_page) ++ { ++ nand_read_page_bmt(PAGE_ADDR(error_block) + page, dat_buf, oob_buf); ++ if (is_page_used(dat_buf, oob_buf)) ++ { ++ if (error_block < system_block_count) ++ { ++ set_bad_index_to_oob(oob_buf, error_block); ++ } ++ MSG(INIT, "\tmigrate page 0x%x to page 0x%x\n", PAGE_ADDR(error_block) + page, PAGE_ADDR(to_index) + page); ++ if (!nand_write_page_bmt(PAGE_ADDR(to_index) + page, dat_buf, oob_buf)) ++ { ++ MSG(INIT, "Write to page 0x%x fail\n", PAGE_ADDR(to_index) + page); ++ mark_block_bad_bmt(to_index); ++ return migrate_from_bad(offset, write_dat, write_oob); ++ } ++ } ++ } ++ } ++ ++ MSG(INIT, "Migrate from 0x%x to 0x%x done!\n", error_block, to_index); ++ ++ return to_index; ++} ++ ++static bool write_bmt_to_flash(u8 * dat, u8 * oob) ++{ ++ bool need_erase = true; ++ MSG(INIT, "Try to write BMT\n"); ++ ++ if (bmt_block_index == 0) ++ { ++ // if we don't have index, we don't need to erase found block as it has been erased in find_available_block() ++ need_erase = false; ++ if (!(bmt_block_index = find_available_block(true))) ++ { ++ MSG(INIT, "Cannot find an available block for BMT\n"); ++ return false; ++ } ++ } ++ ++ MSG(INIT, "Find BMT block: 0x%x\n", bmt_block_index); ++ ++ // write bmt to flash ++ if (need_erase) ++ { ++ if (!nand_erase_bmt(OFFSET(bmt_block_index))) ++ { ++ MSG(INIT, "BMT block erase fail, mark bad: 0x%x\n", bmt_block_index); ++ mark_block_bad_bmt(OFFSET(bmt_block_index)); ++ // bmt.bad_count++; ++ ++ bmt_block_index = 0; ++ return write_bmt_to_flash(dat, oob); // recursive call ++ } ++ } ++ ++ if (!nand_write_page_bmt(PAGE_ADDR(bmt_block_index), dat, oob)) ++ { ++ MSG(INIT, "Write BMT data fail, need to write again\n"); ++ mark_block_bad_bmt(OFFSET(bmt_block_index)); ++ // bmt.bad_count++; ++ ++ bmt_block_index = 0; ++ return write_bmt_to_flash(dat, oob); // recursive call ++ } ++ ++ MSG(INIT, "Write BMT data to block 0x%x success\n", bmt_block_index); ++ return true; ++} ++ ++/******************************************************************* ++* Reconstruct bmt, called when found bmt info doesn't match bad ++* block info in flash. ++* ++* Return NULL for failure ++*******************************************************************/ ++bmt_struct *reconstruct_bmt(bmt_struct * bmt) ++{ ++ int i; ++ int index = system_block_count; ++ unsigned short bad_index; ++ int mapped; ++ ++ // init everything in BMT struct ++ bmt->version = BMT_VERSION; ++ bmt->bad_count = 0; ++ bmt->mapped_count = 0; ++ ++ memset(bmt->table, 0, bmt_block_count * sizeof(bmt_entry)); ++ ++ for (i = 0; i < bmt_block_count; i++, index++) ++ { ++ if (nand_block_bad_bmt(OFFSET(index))) ++ { ++ MSG(INIT, "Skip bad block: 0x%x\n", index); ++ // bmt->bad_count++; ++ continue; ++ } ++ ++ MSG(INIT, "read page: 0x%x\n", PAGE_ADDR(index)); ++ nand_read_page_bmt(PAGE_ADDR(index), dat_buf, oob_buf); ++ /* if (mtk_nand_read_page_hw(PAGE_ADDR(index), dat_buf)) ++ { ++ MSG(INIT, "Error when read block %d\n", bmt_block_index); ++ continue; ++ } */ ++ ++ if ((bad_index = get_bad_index_from_oob(oob_buf)) >= system_block_count) ++ { ++ MSG(INIT, "get bad index: 0x%x\n", bad_index); ++ if (bad_index != 0xFFFF) ++ MSG(INIT, "Invalid bad index found in block 0x%x, bad index 0x%x\n", index, bad_index); ++ continue; ++ } ++ ++ MSG(INIT, "Block 0x%x is mapped to bad block: 0x%x\n", index, bad_index); ++ ++ if (!nand_block_bad_bmt(OFFSET(bad_index))) ++ { ++ MSG(INIT, "\tbut block 0x%x is not marked as bad, invalid mapping\n", bad_index); ++ continue; // no need to erase here, it will be erased later when trying to write BMT ++ } ++ ++ if ((mapped = is_block_mapped(bad_index)) >= 0) ++ { ++ MSG(INIT, "bad block 0x%x is mapped to 0x%x, should be caused by power lost, replace with one\n", bmt->table[mapped].bad_index, bmt->table[mapped].mapped_index); ++ bmt->table[mapped].mapped_index = index; // use new one instead. ++ } else ++ { ++ // add mapping to BMT ++ bmt->table[bmt->mapped_count].bad_index = bad_index; ++ bmt->table[bmt->mapped_count].mapped_index = index; ++ bmt->mapped_count++; ++ } ++ ++ MSG(INIT, "Add mapping: 0x%x -> 0x%x to BMT\n", bad_index, index); ++ ++ } ++ ++ MSG(INIT, "Scan replace pool done, mapped block: %d\n", bmt->mapped_count); ++ // dump_bmt_info(bmt); ++ ++ // fill NAND BMT buffer ++ memset(oob_buf, 0xFF, sizeof(oob_buf)); ++ fill_nand_bmt_buffer(bmt, dat_buf, oob_buf); ++ ++ // write BMT back ++ if (!write_bmt_to_flash(dat_buf, oob_buf)) ++ { ++ MSG(INIT, "TRAGEDY: cannot find a place to write BMT!!!!\n"); ++ } ++ ++ return bmt; ++} ++ ++/******************************************************************* ++* [BMT Interface] ++* ++* Description: ++* Init bmt from nand. Reconstruct if not found or data error ++* ++* Parameter: ++* size: size of bmt and replace pool ++* ++* Return: ++* NULL for failure, and a bmt struct for success ++*******************************************************************/ ++bmt_struct *init_bmt(struct nand_chip * chip, int size) ++{ ++ struct mtk_nand_host *host; ++ ++ if (size > 0 && size < MAX_BMT_SIZE) ++ { ++ MSG(INIT, "Init bmt table, size: %d\n", size); ++ bmt_block_count = size; ++ } else ++ { ++ MSG(INIT, "Invalid bmt table size: %d\n", size); ++ return NULL; ++ } ++ nand_chip_bmt = chip; ++ system_block_count = chip->chipsize >> chip->phys_erase_shift; ++ total_block_count = bmt_block_count + system_block_count; ++ page_per_block = BLOCK_SIZE_BMT / PAGE_SIZE_BMT; ++ host = (struct mtk_nand_host *)chip->priv; ++ mtd_bmt = host->mtd; ++ ++ MSG(INIT, "mtd_bmt: %p, nand_chip_bmt: %p\n", mtd_bmt, nand_chip_bmt); ++ MSG(INIT, "bmt count: %d, system count: %d\n", bmt_block_count, system_block_count); ++ ++ // set this flag, and unmapped block in pool will be erased. ++ pool_erased = 0; ++ memset(bmt.table, 0, size * sizeof(bmt_entry)); ++ if ((bmt_block_index = load_bmt_data(system_block_count, size))) ++ { ++ MSG(INIT, "Load bmt data success @ block 0x%x\n", bmt_block_index); ++ dump_bmt_info(&bmt); ++ return &bmt; ++ } else ++ { ++ MSG(INIT, "Load bmt data fail, need re-construct!\n"); ++#ifndef __UBOOT_NAND__ // BMT is not re-constructed in UBOOT. ++ if (reconstruct_bmt(&bmt)) ++ return &bmt; ++ else ++#endif ++ return NULL; ++ } ++} ++ ++/******************************************************************* ++* [BMT Interface] ++* ++* Description: ++* Update BMT. ++* ++* Parameter: ++* offset: update block/page offset. ++* reason: update reason, see update_reason_t for reason. ++* dat/oob: data and oob buffer for write fail. ++* ++* Return: ++* Return true for success, and false for failure. ++*******************************************************************/ ++bool update_bmt(u32 offset, update_reason_t reason, u8 * dat, u8 * oob) ++{ ++ int map_index; ++ int orig_bad_block = -1; ++ // int bmt_update_index; ++ int i; ++ int bad_index = offset / BLOCK_SIZE_BMT; ++ ++#ifndef MTK_NAND_BMT ++ return false; ++#endif ++ if (reason == UPDATE_WRITE_FAIL) ++ { ++ MSG(INIT, "Write fail, need to migrate\n"); ++ if (!(map_index = migrate_from_bad(offset, dat, oob))) ++ { ++ MSG(INIT, "migrate fail\n"); ++ return false; ++ } ++ } else ++ { ++ if (!(map_index = find_available_block(false))) ++ { ++ MSG(INIT, "Cannot find block in pool\n"); ++ return false; ++ } ++ } ++ ++ // now let's update BMT ++ if (bad_index >= system_block_count) // mapped block become bad, find original bad block ++ { ++ for (i = 0; i < bmt_block_count; i++) ++ { ++ if (bmt.table[i].mapped_index == bad_index) ++ { ++ orig_bad_block = bmt.table[i].bad_index; ++ break; ++ } ++ } ++ // bmt.bad_count++; ++ MSG(INIT, "Mapped block becomes bad, orig bad block is 0x%x\n", orig_bad_block); ++ ++ bmt.table[i].mapped_index = map_index; ++ } else ++ { ++ bmt.table[bmt.mapped_count].mapped_index = map_index; ++ bmt.table[bmt.mapped_count].bad_index = bad_index; ++ bmt.mapped_count++; ++ } ++ ++ memset(oob_buf, 0xFF, sizeof(oob_buf)); ++ fill_nand_bmt_buffer(&bmt, dat_buf, oob_buf); ++ if (!write_bmt_to_flash(dat_buf, oob_buf)) ++ return false; ++ ++ mark_block_bad_bmt(offset); ++ ++ return true; ++} ++ ++/******************************************************************* ++* [BMT Interface] ++* ++* Description: ++* Given an block index, return mapped index if it's mapped, else ++* return given index. ++* ++* Parameter: ++* index: given an block index. This value cannot exceed ++* system_block_count. ++* ++* Return NULL for failure ++*******************************************************************/ ++u16 get_mapping_block_index(int index) ++{ ++ int i; ++#ifndef MTK_NAND_BMT ++ return index; ++#endif ++ if (index > system_block_count) ++ { ++ return index; ++ } ++ ++ for (i = 0; i < bmt.mapped_count; i++) ++ { ++ if (bmt.table[i].bad_index == index) ++ { ++ return bmt.table[i].mapped_index; ++ } ++ } ++ ++ return index; ++} ++#ifdef __KERNEL_NAND__ ++EXPORT_SYMBOL_GPL(init_bmt); ++EXPORT_SYMBOL_GPL(update_bmt); ++EXPORT_SYMBOL_GPL(get_mapping_block_index); ++ ++MODULE_LICENSE("GPL"); ++MODULE_AUTHOR("MediaTek"); ++MODULE_DESCRIPTION("Bad Block mapping management for MediaTek NAND Flash Driver"); ++#endif +--- /dev/null ++++ b/drivers/mtd/nand/bmt.h +@@ -0,0 +1,80 @@ ++#ifndef __BMT_H__ ++#define __BMT_H__ ++ ++#include "nand_def.h" ++ ++#if defined(__PRELOADER_NAND__) ++ ++#include "nand.h" ++ ++#elif defined(__UBOOT_NAND__) ++ ++#include ++#include "mtk_nand2.h" ++ ++#elif defined(__KERNEL_NAND__) ++ ++#include ++#include ++#include ++#include "mtk_nand2.h" ++ ++#endif ++ ++ ++#define MAX_BMT_SIZE (0x80) ++#define BMT_VERSION (1) // initial version ++ ++#define MAIN_SIGNATURE_OFFSET (0) ++#define OOB_SIGNATURE_OFFSET (1) ++#define OOB_INDEX_OFFSET (29) ++#define OOB_INDEX_SIZE (2) ++#define FAKE_INDEX (0xAAAA) ++ ++typedef struct _bmt_entry_ ++{ ++ u16 bad_index; // bad block index ++ u16 mapped_index; // mapping block index in the replace pool ++} bmt_entry; ++ ++typedef enum ++{ ++ UPDATE_ERASE_FAIL, ++ UPDATE_WRITE_FAIL, ++ UPDATE_UNMAPPED_BLOCK, ++ UPDATE_REASON_COUNT, ++} update_reason_t; ++ ++typedef struct ++{ ++ bmt_entry table[MAX_BMT_SIZE]; ++ u8 version; ++ u8 mapped_count; // mapped block count in pool ++ u8 bad_count; // bad block count in pool. Not used in V1 ++} bmt_struct; ++ ++/*************************************************************** ++* * ++* Interface BMT need to use * ++* * ++***************************************************************/ ++extern bool mtk_nand_exec_read_page(struct mtd_info *mtd, u32 row, u32 page_size, u8 * dat, u8 * oob); ++extern int mtk_nand_block_bad_hw(struct mtd_info *mtd, loff_t ofs); ++extern int mtk_nand_erase_hw(struct mtd_info *mtd, int page); ++extern int mtk_nand_block_markbad_hw(struct mtd_info *mtd, loff_t ofs); ++extern int mtk_nand_exec_write_page(struct mtd_info *mtd, u32 row, u32 page_size, u8 * dat, u8 * oob); ++ ++ ++/*************************************************************** ++* * ++* Different function interface for preloader/uboot/kernel * ++* * ++***************************************************************/ ++void set_bad_index_to_oob(u8 * oob, u16 index); ++ ++ ++bmt_struct *init_bmt(struct nand_chip *nand, int size); ++bool update_bmt(u32 offset, update_reason_t reason, u8 * dat, u8 * oob); ++unsigned short get_mapping_block_index(int index); ++ ++#endif // #ifndef __BMT_H__ +--- /dev/null ++++ b/drivers/mtd/nand/dev-nand.c +@@ -0,0 +1,63 @@ ++#include ++#include ++#include ++ ++#include "mt6575_typedefs.h" ++ ++#define RALINK_NAND_CTRL_BASE 0xBE003000 ++#define NFI_base RALINK_NAND_CTRL_BASE ++#define RALINK_NANDECC_CTRL_BASE 0xBE003800 ++#define NFIECC_base RALINK_NANDECC_CTRL_BASE ++#define MT7621_NFI_IRQ_ID SURFBOARDINT_NAND ++#define MT7621_NFIECC_IRQ_ID SURFBOARDINT_NAND_ECC ++ ++#define SURFBOARDINT_NAND 22 ++#define SURFBOARDINT_NAND_ECC 23 ++ ++static struct resource MT7621_resource_nand[] = { ++ { ++ .start = NFI_base, ++ .end = NFI_base + 0x1A0, ++ .flags = IORESOURCE_MEM, ++ }, ++ { ++ .start = NFIECC_base, ++ .end = NFIECC_base + 0x150, ++ .flags = IORESOURCE_MEM, ++ }, ++ { ++ .start = MT7621_NFI_IRQ_ID, ++ .flags = IORESOURCE_IRQ, ++ }, ++ { ++ .start = MT7621_NFIECC_IRQ_ID, ++ .flags = IORESOURCE_IRQ, ++ }, ++}; ++ ++static struct platform_device MT7621_nand_dev = { ++ .name = "MT7621-NAND", ++ .id = 0, ++ .num_resources = ARRAY_SIZE(MT7621_resource_nand), ++ .resource = MT7621_resource_nand, ++ .dev = { ++ .platform_data = &mt7621_nand_hw, ++ }, ++}; ++ ++ ++int __init mtk_nand_register(void) ++{ ++ ++ int retval = 0; ++ ++ retval = platform_device_register(&MT7621_nand_dev); ++ if (retval != 0) { ++ printk(KERN_ERR "register nand device fail\n"); ++ return retval; ++ } ++ ++ ++ return retval; ++} ++arch_initcall(mtk_nand_register); +--- /dev/null ++++ b/drivers/mtd/nand/mt6575_typedefs.h +@@ -0,0 +1,340 @@ ++/* Copyright Statement: ++ * ++ * This software/firmware and related documentation ("MediaTek Software") are ++ * protected under relevant copyright laws. The information contained herein ++ * is confidential and proprietary to MediaTek Inc. and/or its licensors. ++ * Without the prior written permission of MediaTek inc. and/or its licensors, ++ * any reproduction, modification, use or disclosure of MediaTek Software, ++ * and information contained herein, in whole or in part, shall be strictly prohibited. ++ */ ++/* MediaTek Inc. (C) 2010. All rights reserved. ++ * ++ * BY OPENING THIS FILE, RECEIVER HEREBY UNEQUIVOCALLY ACKNOWLEDGES AND AGREES ++ * THAT THE SOFTWARE/FIRMWARE AND ITS DOCUMENTATIONS ("MEDIATEK SOFTWARE") ++ * RECEIVED FROM MEDIATEK AND/OR ITS REPRESENTATIVES ARE PROVIDED TO RECEIVER ON ++ * AN "AS-IS" BASIS ONLY. MEDIATEK EXPRESSLY DISCLAIMS ANY AND ALL WARRANTIES, ++ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF ++ * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT. ++ * NEITHER DOES MEDIATEK PROVIDE ANY WARRANTY WHATSOEVER WITH RESPECT TO THE ++ * SOFTWARE OF ANY THIRD PARTY WHICH MAY BE USED BY, INCORPORATED IN, OR ++ * SUPPLIED WITH THE MEDIATEK SOFTWARE, AND RECEIVER AGREES TO LOOK ONLY TO SUCH ++ * THIRD PARTY FOR ANY WARRANTY CLAIM RELATING THERETO. RECEIVER EXPRESSLY ACKNOWLEDGES ++ * THAT IT IS RECEIVER'S SOLE RESPONSIBILITY TO OBTAIN FROM ANY THIRD PARTY ALL PROPER LICENSES ++ * CONTAINED IN MEDIATEK SOFTWARE. MEDIATEK SHALL ALSO NOT BE RESPONSIBLE FOR ANY MEDIATEK ++ * SOFTWARE RELEASES MADE TO RECEIVER'S SPECIFICATION OR TO CONFORM TO A PARTICULAR ++ * STANDARD OR OPEN FORUM. RECEIVER'S SOLE AND EXCLUSIVE REMEDY AND MEDIATEK'S ENTIRE AND ++ * CUMULATIVE LIABILITY WITH RESPECT TO THE MEDIATEK SOFTWARE RELEASED HEREUNDER WILL BE, ++ * AT MEDIATEK'S OPTION, TO REVISE OR REPLACE THE MEDIATEK SOFTWARE AT ISSUE, ++ * OR REFUND ANY SOFTWARE LICENSE FEES OR SERVICE CHARGE PAID BY RECEIVER TO ++ * MEDIATEK FOR SUCH MEDIATEK SOFTWARE AT ISSUE. ++ * ++ * The following software/firmware and/or related documentation ("MediaTek Software") ++ * have been modified by MediaTek Inc. All revisions are subject to any receiver's ++ * applicable license agreements with MediaTek Inc. ++ */ ++ ++/***************************************************************************** ++* Copyright Statement: ++* -------------------- ++* This software is protected by Copyright and the information contained ++* herein is confidential. The software may not be copied and the information ++* contained herein may not be used or disclosed except with the written ++* permission of MediaTek Inc. (C) 2008 ++* ++* BY OPENING THIS FILE, BUYER HEREBY UNEQUIVOCALLY ACKNOWLEDGES AND AGREES ++* THAT THE SOFTWARE/FIRMWARE AND ITS DOCUMENTATIONS ("MEDIATEK SOFTWARE") ++* RECEIVED FROM MEDIATEK AND/OR ITS REPRESENTATIVES ARE PROVIDED TO BUYER ON ++* AN "AS-IS" BASIS ONLY. MEDIATEK EXPRESSLY DISCLAIMS ANY AND ALL WARRANTIES, ++* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF ++* MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT. ++* NEITHER DOES MEDIATEK PROVIDE ANY WARRANTY WHATSOEVER WITH RESPECT TO THE ++* SOFTWARE OF ANY THIRD PARTY WHICH MAY BE USED BY, INCORPORATED IN, OR ++* SUPPLIED WITH THE MEDIATEK SOFTWARE, AND BUYER AGREES TO LOOK ONLY TO SUCH ++* THIRD PARTY FOR ANY WARRANTY CLAIM RELATING THERETO. MEDIATEK SHALL ALSO ++* NOT BE RESPONSIBLE FOR ANY MEDIATEK SOFTWARE RELEASES MADE TO BUYER'S ++* SPECIFICATION OR TO CONFORM TO A PARTICULAR STANDARD OR OPEN FORUM. ++* ++* BUYER'S SOLE AND EXCLUSIVE REMEDY AND MEDIATEK'S ENTIRE AND CUMULATIVE ++* LIABILITY WITH RESPECT TO THE MEDIATEK SOFTWARE RELEASED HEREUNDER WILL BE, ++* AT MEDIATEK'S OPTION, TO REVISE OR REPLACE THE MEDIATEK SOFTWARE AT ISSUE, ++* OR REFUND ANY SOFTWARE LICENSE FEES OR SERVICE CHARGE PAID BY BUYER TO ++* MEDIATEK FOR SUCH MEDIATEK SOFTWARE AT ISSUE. ++* ++* THE TRANSACTION CONTEMPLATED HEREUNDER SHALL BE CONSTRUED IN ACCORDANCE ++* WITH THE LAWS OF THE STATE OF CALIFORNIA, USA, EXCLUDING ITS CONFLICT OF ++* LAWS PRINCIPLES. ANY DISPUTES, CONTROVERSIES OR CLAIMS ARISING THEREOF AND ++* RELATED THERETO SHALL BE SETTLED BY ARBITRATION IN SAN FRANCISCO, CA, UNDER ++* THE RULES OF THE INTERNATIONAL CHAMBER OF COMMERCE (ICC). ++* ++*****************************************************************************/ ++ ++#ifndef _MT6575_TYPEDEFS_H ++#define _MT6575_TYPEDEFS_H ++ ++#if defined (__KERNEL_NAND__) ++#include ++#else ++#define true 1 ++#define false 0 ++#define bool u8 ++#endif ++ ++// --------------------------------------------------------------------------- ++// Basic Type Definitions ++// --------------------------------------------------------------------------- ++ ++typedef volatile unsigned char *P_kal_uint8; ++typedef volatile unsigned short *P_kal_uint16; ++typedef volatile unsigned int *P_kal_uint32; ++ ++typedef long LONG; ++typedef unsigned char UBYTE; ++typedef short SHORT; ++ ++typedef signed char kal_int8; ++typedef signed short kal_int16; ++typedef signed int kal_int32; ++typedef long long kal_int64; ++typedef unsigned char kal_uint8; ++typedef unsigned short kal_uint16; ++typedef unsigned int kal_uint32; ++typedef unsigned long long kal_uint64; ++typedef char kal_char; ++ ++typedef unsigned int *UINT32P; ++typedef volatile unsigned short *UINT16P; ++typedef volatile unsigned char *UINT8P; ++typedef unsigned char *U8P; ++ ++typedef volatile unsigned char *P_U8; ++typedef volatile signed char *P_S8; ++typedef volatile unsigned short *P_U16; ++typedef volatile signed short *P_S16; ++typedef volatile unsigned int *P_U32; ++typedef volatile signed int *P_S32; ++typedef unsigned long long *P_U64; ++typedef signed long long *P_S64; ++ ++typedef unsigned char U8; ++typedef signed char S8; ++typedef unsigned short U16; ++typedef signed short S16; ++typedef unsigned int U32; ++typedef signed int S32; ++typedef unsigned long long U64; ++typedef signed long long S64; ++//typedef unsigned char bool; ++ ++typedef unsigned char UINT8; ++typedef unsigned short UINT16; ++typedef unsigned int UINT32; ++typedef unsigned short USHORT; ++typedef signed char INT8; ++typedef signed short INT16; ++typedef signed int INT32; ++typedef unsigned int DWORD; ++typedef void VOID; ++typedef unsigned char BYTE; ++typedef float FLOAT; ++ ++typedef char *LPCSTR; ++typedef short *LPWSTR; ++ ++ ++// --------------------------------------------------------------------------- ++// Constants ++// --------------------------------------------------------------------------- ++ ++#define IMPORT EXTERN ++#ifndef __cplusplus ++ #define EXTERN extern ++#else ++ #define EXTERN extern "C" ++#endif ++#define LOCAL static ++#define GLOBAL ++#define EXPORT GLOBAL ++ ++#define EQ == ++#define NEQ != ++#define AND && ++#define OR || ++#define XOR(A,B) ((!(A) AND (B)) OR ((A) AND !(B))) ++ ++#ifndef FALSE ++ #define FALSE (0) ++#endif ++ ++#ifndef TRUE ++ #define TRUE (1) ++#endif ++ ++#ifndef NULL ++ #define NULL (0) ++#endif ++ ++//enum boolean {false, true}; ++enum {RX, TX, NONE}; ++ ++#ifndef BOOL ++typedef unsigned char BOOL; ++#endif ++ ++typedef enum { ++ KAL_FALSE = 0, ++ KAL_TRUE = 1, ++} kal_bool; ++ ++ ++// --------------------------------------------------------------------------- ++// Type Casting ++// --------------------------------------------------------------------------- ++ ++#define AS_INT32(x) (*(INT32 *)((void*)x)) ++#define AS_INT16(x) (*(INT16 *)((void*)x)) ++#define AS_INT8(x) (*(INT8 *)((void*)x)) ++ ++#define AS_UINT32(x) (*(UINT32 *)((void*)x)) ++#define AS_UINT16(x) (*(UINT16 *)((void*)x)) ++#define AS_UINT8(x) (*(UINT8 *)((void*)x)) ++ ++ ++// --------------------------------------------------------------------------- ++// Register Manipulations ++// --------------------------------------------------------------------------- ++ ++#define READ_REGISTER_UINT32(reg) \ ++ (*(volatile UINT32 * const)(reg)) ++ ++#define WRITE_REGISTER_UINT32(reg, val) \ ++ (*(volatile UINT32 * const)(reg)) = (val) ++ ++#define READ_REGISTER_UINT16(reg) \ ++ (*(volatile UINT16 * const)(reg)) ++ ++#define WRITE_REGISTER_UINT16(reg, val) \ ++ (*(volatile UINT16 * const)(reg)) = (val) ++ ++#define READ_REGISTER_UINT8(reg) \ ++ (*(volatile UINT8 * const)(reg)) ++ ++#define WRITE_REGISTER_UINT8(reg, val) \ ++ (*(volatile UINT8 * const)(reg)) = (val) ++ ++#define INREG8(x) READ_REGISTER_UINT8((UINT8*)((void*)(x))) ++#define OUTREG8(x, y) WRITE_REGISTER_UINT8((UINT8*)((void*)(x)), (UINT8)(y)) ++#define SETREG8(x, y) OUTREG8(x, INREG8(x)|(y)) ++#define CLRREG8(x, y) OUTREG8(x, INREG8(x)&~(y)) ++#define MASKREG8(x, y, z) OUTREG8(x, (INREG8(x)&~(y))|(z)) ++ ++#define INREG16(x) READ_REGISTER_UINT16((UINT16*)((void*)(x))) ++#define OUTREG16(x, y) WRITE_REGISTER_UINT16((UINT16*)((void*)(x)),(UINT16)(y)) ++#define SETREG16(x, y) OUTREG16(x, INREG16(x)|(y)) ++#define CLRREG16(x, y) OUTREG16(x, INREG16(x)&~(y)) ++#define MASKREG16(x, y, z) OUTREG16(x, (INREG16(x)&~(y))|(z)) ++ ++#define INREG32(x) READ_REGISTER_UINT32((UINT32*)((void*)(x))) ++#define OUTREG32(x, y) WRITE_REGISTER_UINT32((UINT32*)((void*)(x)), (UINT32)(y)) ++#define SETREG32(x, y) OUTREG32(x, INREG32(x)|(y)) ++#define CLRREG32(x, y) OUTREG32(x, INREG32(x)&~(y)) ++#define MASKREG32(x, y, z) OUTREG32(x, (INREG32(x)&~(y))|(z)) ++ ++ ++#define DRV_Reg8(addr) INREG8(addr) ++#define DRV_WriteReg8(addr, data) OUTREG8(addr, data) ++#define DRV_SetReg8(addr, data) SETREG8(addr, data) ++#define DRV_ClrReg8(addr, data) CLRREG8(addr, data) ++ ++#define DRV_Reg16(addr) INREG16(addr) ++#define DRV_WriteReg16(addr, data) OUTREG16(addr, data) ++#define DRV_SetReg16(addr, data) SETREG16(addr, data) ++#define DRV_ClrReg16(addr, data) CLRREG16(addr, data) ++ ++#define DRV_Reg32(addr) INREG32(addr) ++#define DRV_WriteReg32(addr, data) OUTREG32(addr, data) ++#define DRV_SetReg32(addr, data) SETREG32(addr, data) ++#define DRV_ClrReg32(addr, data) CLRREG32(addr, data) ++ ++// !!! DEPRECATED, WILL BE REMOVED LATER !!! ++#define DRV_Reg(addr) DRV_Reg16(addr) ++#define DRV_WriteReg(addr, data) DRV_WriteReg16(addr, data) ++#define DRV_SetReg(addr, data) DRV_SetReg16(addr, data) ++#define DRV_ClrReg(addr, data) DRV_ClrReg16(addr, data) ++ ++ ++// --------------------------------------------------------------------------- ++// Compiler Time Deduction Macros ++// --------------------------------------------------------------------------- ++ ++#define _MASK_OFFSET_1(x, n) ((x) & 0x1) ? (n) : ++#define _MASK_OFFSET_2(x, n) _MASK_OFFSET_1((x), (n)) _MASK_OFFSET_1((x) >> 1, (n) + 1) ++#define _MASK_OFFSET_4(x, n) _MASK_OFFSET_2((x), (n)) _MASK_OFFSET_2((x) >> 2, (n) + 2) ++#define _MASK_OFFSET_8(x, n) _MASK_OFFSET_4((x), (n)) _MASK_OFFSET_4((x) >> 4, (n) + 4) ++#define _MASK_OFFSET_16(x, n) _MASK_OFFSET_8((x), (n)) _MASK_OFFSET_8((x) >> 8, (n) + 8) ++#define _MASK_OFFSET_32(x, n) _MASK_OFFSET_16((x), (n)) _MASK_OFFSET_16((x) >> 16, (n) + 16) ++ ++#define MASK_OFFSET_ERROR (0xFFFFFFFF) ++ ++#define MASK_OFFSET(x) (_MASK_OFFSET_32(x, 0) MASK_OFFSET_ERROR) ++ ++ ++// --------------------------------------------------------------------------- ++// Assertions ++// --------------------------------------------------------------------------- ++ ++#ifndef ASSERT ++ #define ASSERT(expr) BUG_ON(!(expr)) ++#endif ++ ++#ifndef NOT_IMPLEMENTED ++ #define NOT_IMPLEMENTED() BUG_ON(1) ++#endif ++ ++#define STATIC_ASSERT(pred) STATIC_ASSERT_X(pred, __LINE__) ++#define STATIC_ASSERT_X(pred, line) STATIC_ASSERT_XX(pred, line) ++#define STATIC_ASSERT_XX(pred, line) \ ++ extern char assertion_failed_at_##line[(pred) ? 1 : -1] ++ ++// --------------------------------------------------------------------------- ++// Resolve Compiler Warnings ++// --------------------------------------------------------------------------- ++ ++#define NOT_REFERENCED(x) { (x) = (x); } ++ ++ ++// --------------------------------------------------------------------------- ++// Utilities ++// --------------------------------------------------------------------------- ++ ++#define MAXIMUM(A,B) (((A)>(B))?(A):(B)) ++#define MINIMUM(A,B) (((A)<(B))?(A):(B)) ++ ++#define ARY_SIZE(x) (sizeof((x)) / sizeof((x[0]))) ++#define DVT_DELAYMACRO(u4Num) \ ++{ \ ++ UINT32 u4Count = 0 ; \ ++ for (u4Count = 0; u4Count < u4Num; u4Count++ ); \ ++} \ ++ ++#define A68351B 0 ++#define B68351B 1 ++#define B68351D 2 ++#define B68351E 3 ++#define UNKNOWN_IC_VERSION 0xFF ++ ++/* NAND driver */ ++struct mtk_nand_host_hw { ++ unsigned int nfi_bus_width; /* NFI_BUS_WIDTH */ ++ unsigned int nfi_access_timing; /* NFI_ACCESS_TIMING */ ++ unsigned int nfi_cs_num; /* NFI_CS_NUM */ ++ unsigned int nand_sec_size; /* NAND_SECTOR_SIZE */ ++ unsigned int nand_sec_shift; /* NAND_SECTOR_SHIFT */ ++ unsigned int nand_ecc_size; ++ unsigned int nand_ecc_bytes; ++ unsigned int nand_ecc_mode; ++}; ++extern struct mtk_nand_host_hw mt7621_nand_hw; ++extern unsigned int CFG_BLOCKSIZE; ++ ++#endif // _MT6575_TYPEDEFS_H ++ +--- /dev/null ++++ b/drivers/mtd/nand/mtk_nand2.c +@@ -0,0 +1,2345 @@ ++/****************************************************************************** ++* mtk_nand2.c - MTK NAND Flash Device Driver ++ * ++* Copyright 2009-2012 MediaTek Co.,Ltd. ++ * ++* DESCRIPTION: ++* This file provid the other drivers nand relative functions ++ * ++* modification history ++* ---------------------------------------- ++* v3.0, 11 Feb 2010, mtk ++* ---------------------------------------- ++******************************************************************************/ ++#include "nand_def.h" ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include "mtk_nand2.h" ++#include "nand_device_list.h" ++ ++#include "bmt.h" ++#include "partition.h" ++ ++unsigned int CFG_BLOCKSIZE; ++ ++static int shift_on_bbt = 0; ++int mtk_nand_read_oob_hw(struct mtd_info *mtd, struct nand_chip *chip, int page); ++ ++static const char * const probe_types[] = { "cmdlinepart", "ofpart", NULL }; ++ ++#define NAND_CMD_STATUS_MULTI 0x71 ++ ++void show_stack(struct task_struct *tsk, unsigned long *sp); ++extern void mt_irq_set_sens(unsigned int irq, unsigned int sens); ++extern void mt_irq_set_polarity(unsigned int irq,unsigned int polarity); ++ ++struct mtk_nand_host mtk_nand_host; /* include mtd_info and nand_chip structs */ ++struct mtk_nand_host_hw mt7621_nand_hw = { ++ .nfi_bus_width = 8, ++ .nfi_access_timing = NFI_DEFAULT_ACCESS_TIMING, ++ .nfi_cs_num = NFI_CS_NUM, ++ .nand_sec_size = 512, ++ .nand_sec_shift = 9, ++ .nand_ecc_size = 2048, ++ .nand_ecc_bytes = 32, ++ .nand_ecc_mode = NAND_ECC_HW, ++}; ++ ++ ++/******************************************************************************* ++ * Gloable Varible Definition ++ *******************************************************************************/ ++ ++#define NFI_ISSUE_COMMAND(cmd, col_addr, row_addr, col_num, row_num) \ ++ do { \ ++ DRV_WriteReg(NFI_CMD_REG16,cmd);\ ++ while (DRV_Reg32(NFI_STA_REG32) & STA_CMD_STATE);\ ++ DRV_WriteReg32(NFI_COLADDR_REG32, col_addr);\ ++ DRV_WriteReg32(NFI_ROWADDR_REG32, row_addr);\ ++ DRV_WriteReg(NFI_ADDRNOB_REG16, col_num | (row_num<priv; ++ int block; ++ ++ block = (int)(page >> (this->bbt_erase_shift - this->page_shift - 1)); ++ this->bbt[block >> 3] &= ~(0x03 << (block & 0x6)); ++ this->bbt[block >> 3] |= (flag & 0x3) << (block & 0x6); ++} ++ ++static int nand_bbt_get(struct mtd_info *mtd, int page) ++{ ++ struct nand_chip *this = mtd->priv; ++ int block; ++ ++ block = (int)(page >> (this->bbt_erase_shift - this->page_shift - 1)); ++ return (this->bbt[block >> 3] >> (block & 0x06)) & 0x03; ++} ++ ++void nand_enable_clock(void) ++{ ++ //enable_clock(MT65XX_PDN_PERI_NFI, "NAND"); ++} ++ ++void nand_disable_clock(void) ++{ ++ //disable_clock(MT65XX_PDN_PERI_NFI, "NAND"); ++} ++ ++struct nand_ecclayout { ++ __u32 eccbytes; ++ __u32 eccpos[MTD_MAX_ECCPOS_ENTRIES_LARGE]; ++ __u32 oobavail; ++ struct nand_oobfree oobfree[MTD_MAX_OOBFREE_ENTRIES_LARGE]; ++}; ++ ++static struct nand_ecclayout *layout; ++ ++static struct nand_ecclayout nand_oob_16 = { ++ .eccbytes = 8, ++ .eccpos = {8, 9, 10, 11, 12, 13, 14, 15}, ++ .oobfree = {{1, 6}, {0, 0}} ++}; ++ ++struct nand_ecclayout nand_oob_64 = { ++ .eccbytes = 32, ++ .eccpos = {32, 33, 34, 35, 36, 37, 38, 39, ++ 40, 41, 42, 43, 44, 45, 46, 47, ++ 48, 49, 50, 51, 52, 53, 54, 55, ++ 56, 57, 58, 59, 60, 61, 62, 63}, ++ .oobfree = {{1, 7}, {9, 7}, {17, 7}, {25, 6}, {0, 0}} ++}; ++ ++struct nand_ecclayout nand_oob_128 = { ++ .eccbytes = 64, ++ .eccpos = { ++ 64, 65, 66, 67, 68, 69, 70, 71, ++ 72, 73, 74, 75, 76, 77, 78, 79, ++ 80, 81, 82, 83, 84, 85, 86, 86, ++ 88, 89, 90, 91, 92, 93, 94, 95, ++ 96, 97, 98, 99, 100, 101, 102, 103, ++ 104, 105, 106, 107, 108, 109, 110, 111, ++ 112, 113, 114, 115, 116, 117, 118, 119, ++ 120, 121, 122, 123, 124, 125, 126, 127}, ++ .oobfree = {{1, 7}, {9, 7}, {17, 7}, {25, 7}, {33, 7}, {41, 7}, {49, 7}, {57, 6}} ++}; ++ ++flashdev_info devinfo; ++ ++void dump_nfi(void) ++{ ++} ++ ++void dump_ecc(void) ++{ ++} ++ ++u32 ++nand_virt_to_phys_add(u32 va) ++{ ++ u32 pageOffset = (va & (PAGE_SIZE - 1)); ++ pgd_t *pgd; ++ pmd_t *pmd; ++ pte_t *pte; ++ u32 pa; ++ ++ if (virt_addr_valid(va)) ++ return __virt_to_phys(va); ++ ++ if (NULL == current) { ++ printk(KERN_ERR "[nand_virt_to_phys_add] ERROR ,current is NULL! \n"); ++ return 0; ++ } ++ ++ if (NULL == current->mm) { ++ printk(KERN_ERR "[nand_virt_to_phys_add] ERROR current->mm is NULL! tgid=0x%x, name=%s \n", current->tgid, current->comm); ++ return 0; ++ } ++ ++ pgd = pgd_offset(current->mm, va); /* what is tsk->mm */ ++ if (pgd_none(*pgd) || pgd_bad(*pgd)) { ++ printk(KERN_ERR "[nand_virt_to_phys_add] ERROR, va=0x%x, pgd invalid! \n", va); ++ return 0; ++ } ++ ++ pmd = pmd_offset((pud_t *)pgd, va); ++ if (pmd_none(*pmd) || pmd_bad(*pmd)) { ++ printk(KERN_ERR "[nand_virt_to_phys_add] ERROR, va=0x%x, pmd invalid! \n", va); ++ return 0; ++ } ++ ++ pte = pte_offset_map(pmd, va); ++ if (pte_present(*pte)) { ++ pa = (pte_val(*pte) & (PAGE_MASK)) | pageOffset; ++ return pa; ++ } ++ ++ printk(KERN_ERR "[nand_virt_to_phys_add] ERROR va=0x%x, pte invalid! \n", va); ++ return 0; ++} ++EXPORT_SYMBOL(nand_virt_to_phys_add); ++ ++bool ++get_device_info(u16 id, u32 ext_id, flashdev_info * pdevinfo) ++{ ++ u32 index; ++ for (index = 0; gen_FlashTable[index].id != 0; index++) { ++ if (id == gen_FlashTable[index].id && ext_id == gen_FlashTable[index].ext_id) { ++ pdevinfo->id = gen_FlashTable[index].id; ++ pdevinfo->ext_id = gen_FlashTable[index].ext_id; ++ pdevinfo->blocksize = gen_FlashTable[index].blocksize; ++ pdevinfo->addr_cycle = gen_FlashTable[index].addr_cycle; ++ pdevinfo->iowidth = gen_FlashTable[index].iowidth; ++ pdevinfo->timmingsetting = gen_FlashTable[index].timmingsetting; ++ pdevinfo->advancedmode = gen_FlashTable[index].advancedmode; ++ pdevinfo->pagesize = gen_FlashTable[index].pagesize; ++ pdevinfo->sparesize = gen_FlashTable[index].sparesize; ++ pdevinfo->totalsize = gen_FlashTable[index].totalsize; ++ memcpy(pdevinfo->devciename, gen_FlashTable[index].devciename, sizeof(pdevinfo->devciename)); ++ printk(KERN_INFO "Device found in MTK table, ID: %x, EXT_ID: %x\n", id, ext_id); ++ ++ goto find; ++ } ++ } ++ ++find: ++ if (0 == pdevinfo->id) { ++ printk(KERN_INFO "Device not found, ID: %x\n", id); ++ return false; ++ } else { ++ return true; ++ } ++} ++ ++static void ++ECC_Config(struct mtk_nand_host_hw *hw,u32 ecc_bit) ++{ ++ u32 u4ENCODESize; ++ u32 u4DECODESize; ++ u32 ecc_bit_cfg = ECC_CNFG_ECC4; ++ ++ switch(ecc_bit){ ++ case 4: ++ ecc_bit_cfg = ECC_CNFG_ECC4; ++ break; ++ case 8: ++ ecc_bit_cfg = ECC_CNFG_ECC8; ++ break; ++ case 10: ++ ecc_bit_cfg = ECC_CNFG_ECC10; ++ break; ++ case 12: ++ ecc_bit_cfg = ECC_CNFG_ECC12; ++ break; ++ default: ++ break; ++ } ++ DRV_WriteReg16(ECC_DECCON_REG16, DEC_DE); ++ do { ++ } while (!DRV_Reg16(ECC_DECIDLE_REG16)); ++ ++ DRV_WriteReg16(ECC_ENCCON_REG16, ENC_DE); ++ do { ++ } while (!DRV_Reg32(ECC_ENCIDLE_REG32)); ++ ++ /* setup FDM register base */ ++ DRV_WriteReg32(ECC_FDMADDR_REG32, NFI_FDM0L_REG32); ++ ++ /* Sector + FDM */ ++ u4ENCODESize = (hw->nand_sec_size + 8) << 3; ++ /* Sector + FDM + YAFFS2 meta data bits */ ++ u4DECODESize = ((hw->nand_sec_size + 8) << 3) + ecc_bit * 13; ++ ++ /* configure ECC decoder && encoder */ ++ DRV_WriteReg32(ECC_DECCNFG_REG32, ecc_bit_cfg | DEC_CNFG_NFI | DEC_CNFG_EMPTY_EN | (u4DECODESize << DEC_CNFG_CODE_SHIFT)); ++ ++ DRV_WriteReg32(ECC_ENCCNFG_REG32, ecc_bit_cfg | ENC_CNFG_NFI | (u4ENCODESize << ENC_CNFG_MSG_SHIFT)); ++ NFI_SET_REG32(ECC_DECCNFG_REG32, DEC_CNFG_EL); ++} ++ ++static void ++ECC_Decode_Start(void) ++{ ++ while (!(DRV_Reg16(ECC_DECIDLE_REG16) & DEC_IDLE)) ++ ; ++ DRV_WriteReg16(ECC_DECCON_REG16, DEC_EN); ++} ++ ++static void ++ECC_Decode_End(void) ++{ ++ while (!(DRV_Reg16(ECC_DECIDLE_REG16) & DEC_IDLE)) ++ ; ++ DRV_WriteReg16(ECC_DECCON_REG16, DEC_DE); ++} ++ ++static void ++ECC_Encode_Start(void) ++{ ++ while (!(DRV_Reg32(ECC_ENCIDLE_REG32) & ENC_IDLE)) ++ ; ++ mb(); ++ DRV_WriteReg16(ECC_ENCCON_REG16, ENC_EN); ++} ++ ++static void ++ECC_Encode_End(void) ++{ ++ /* wait for device returning idle */ ++ while (!(DRV_Reg32(ECC_ENCIDLE_REG32) & ENC_IDLE)) ; ++ mb(); ++ DRV_WriteReg16(ECC_ENCCON_REG16, ENC_DE); ++} ++ ++static bool ++mtk_nand_check_bch_error(struct mtd_info *mtd, u8 * pDataBuf, u32 u4SecIndex, u32 u4PageAddr) ++{ ++ bool bRet = true; ++ u16 u2SectorDoneMask = 1 << u4SecIndex; ++ u32 u4ErrorNumDebug, i, u4ErrNum; ++ u32 timeout = 0xFFFF; ++ // int el; ++ u32 au4ErrBitLoc[6]; ++ u32 u4ErrByteLoc, u4BitOffset; ++ u32 u4ErrBitLoc1th, u4ErrBitLoc2nd; ++ ++ //4 // Wait for Decode Done ++ while (0 == (u2SectorDoneMask & DRV_Reg16(ECC_DECDONE_REG16))) { ++ timeout--; ++ if (0 == timeout) ++ return false; ++ } ++ /* We will manually correct the error bits in the last sector, not all the sectors of the page! */ ++ memset(au4ErrBitLoc, 0x0, sizeof(au4ErrBitLoc)); ++ u4ErrorNumDebug = DRV_Reg32(ECC_DECENUM_REG32); ++ u4ErrNum = DRV_Reg32(ECC_DECENUM_REG32) >> (u4SecIndex << 2); ++ u4ErrNum &= 0xF; ++ ++ if (u4ErrNum) { ++ if (0xF == u4ErrNum) { ++ mtd->ecc_stats.failed++; ++ bRet = false; ++ printk(KERN_ERR"mtk_nand: UnCorrectable at PageAddr=%d\n", u4PageAddr); ++ } else { ++ for (i = 0; i < ((u4ErrNum + 1) >> 1); ++i) { ++ au4ErrBitLoc[i] = DRV_Reg32(ECC_DECEL0_REG32 + i); ++ u4ErrBitLoc1th = au4ErrBitLoc[i] & 0x1FFF; ++ if (u4ErrBitLoc1th < 0x1000) { ++ u4ErrByteLoc = u4ErrBitLoc1th / 8; ++ u4BitOffset = u4ErrBitLoc1th % 8; ++ pDataBuf[u4ErrByteLoc] = pDataBuf[u4ErrByteLoc] ^ (1 << u4BitOffset); ++ mtd->ecc_stats.corrected++; ++ } else { ++ mtd->ecc_stats.failed++; ++ } ++ u4ErrBitLoc2nd = (au4ErrBitLoc[i] >> 16) & 0x1FFF; ++ if (0 != u4ErrBitLoc2nd) { ++ if (u4ErrBitLoc2nd < 0x1000) { ++ u4ErrByteLoc = u4ErrBitLoc2nd / 8; ++ u4BitOffset = u4ErrBitLoc2nd % 8; ++ pDataBuf[u4ErrByteLoc] = pDataBuf[u4ErrByteLoc] ^ (1 << u4BitOffset); ++ mtd->ecc_stats.corrected++; ++ } else { ++ mtd->ecc_stats.failed++; ++ //printk(KERN_ERR"UnCorrectable High ErrLoc=%d\n", au4ErrBitLoc[i]); ++ } ++ } ++ } ++ } ++ if (0 == (DRV_Reg16(ECC_DECFER_REG16) & (1 << u4SecIndex))) ++ bRet = false; ++ } ++ return bRet; ++} ++ ++static bool ++mtk_nand_RFIFOValidSize(u16 u2Size) ++{ ++ u32 timeout = 0xFFFF; ++ while (FIFO_RD_REMAIN(DRV_Reg16(NFI_FIFOSTA_REG16)) < u2Size) { ++ timeout--; ++ if (0 == timeout) ++ return false; ++ } ++ return true; ++} ++ ++static bool ++mtk_nand_WFIFOValidSize(u16 u2Size) ++{ ++ u32 timeout = 0xFFFF; ++ ++ while (FIFO_WR_REMAIN(DRV_Reg16(NFI_FIFOSTA_REG16)) > u2Size) { ++ timeout--; ++ if (0 == timeout) ++ return false; ++ } ++ return true; ++} ++ ++static bool ++mtk_nand_status_ready(u32 u4Status) ++{ ++ u32 timeout = 0xFFFF; ++ ++ while ((DRV_Reg32(NFI_STA_REG32) & u4Status) != 0) { ++ timeout--; ++ if (0 == timeout) ++ return false; ++ } ++ return true; ++} ++ ++static bool ++mtk_nand_reset(void) ++{ ++ int timeout = 0xFFFF; ++ if (DRV_Reg16(NFI_MASTERSTA_REG16)) { ++ mb(); ++ DRV_WriteReg16(NFI_CON_REG16, CON_FIFO_FLUSH | CON_NFI_RST); ++ while (DRV_Reg16(NFI_MASTERSTA_REG16)) { ++ timeout--; ++ if (!timeout) ++ MSG(INIT, "Wait for NFI_MASTERSTA timeout\n"); ++ } ++ } ++ /* issue reset operation */ ++ mb(); ++ DRV_WriteReg16(NFI_CON_REG16, CON_FIFO_FLUSH | CON_NFI_RST); ++ ++ return mtk_nand_status_ready(STA_NFI_FSM_MASK | STA_NAND_BUSY) && mtk_nand_RFIFOValidSize(0) && mtk_nand_WFIFOValidSize(0); ++} ++ ++static void ++mtk_nand_set_mode(u16 u2OpMode) ++{ ++ u16 u2Mode = DRV_Reg16(NFI_CNFG_REG16); ++ u2Mode &= ~CNFG_OP_MODE_MASK; ++ u2Mode |= u2OpMode; ++ DRV_WriteReg16(NFI_CNFG_REG16, u2Mode); ++} ++ ++static void ++mtk_nand_set_autoformat(bool bEnable) ++{ ++ if (bEnable) ++ NFI_SET_REG16(NFI_CNFG_REG16, CNFG_AUTO_FMT_EN); ++ else ++ NFI_CLN_REG16(NFI_CNFG_REG16, CNFG_AUTO_FMT_EN); ++} ++ ++static void ++mtk_nand_configure_fdm(u16 u2FDMSize) ++{ ++ NFI_CLN_REG16(NFI_PAGEFMT_REG16, PAGEFMT_FDM_MASK | PAGEFMT_FDM_ECC_MASK); ++ NFI_SET_REG16(NFI_PAGEFMT_REG16, u2FDMSize << PAGEFMT_FDM_SHIFT); ++ NFI_SET_REG16(NFI_PAGEFMT_REG16, u2FDMSize << PAGEFMT_FDM_ECC_SHIFT); ++} ++ ++static void ++mtk_nand_configure_lock(void) ++{ ++ u32 u4WriteColNOB = 2; ++ u32 u4WriteRowNOB = 3; ++ u32 u4EraseColNOB = 0; ++ u32 u4EraseRowNOB = 3; ++ DRV_WriteReg16(NFI_LOCKANOB_REG16, ++ (u4WriteColNOB << PROG_CADD_NOB_SHIFT) | (u4WriteRowNOB << PROG_RADD_NOB_SHIFT) | (u4EraseColNOB << ERASE_CADD_NOB_SHIFT) | (u4EraseRowNOB << ERASE_RADD_NOB_SHIFT)); ++ ++ if (CHIPVER_ECO_1 == g_u4ChipVer) { ++ int i; ++ for (i = 0; i < 16; ++i) { ++ DRV_WriteReg32(NFI_LOCK00ADD_REG32 + (i << 1), 0xFFFFFFFF); ++ DRV_WriteReg32(NFI_LOCK00FMT_REG32 + (i << 1), 0xFFFFFFFF); ++ } ++ //DRV_WriteReg16(NFI_LOCKANOB_REG16, 0x0); ++ DRV_WriteReg32(NFI_LOCKCON_REG32, 0xFFFFFFFF); ++ DRV_WriteReg16(NFI_LOCK_REG16, NFI_LOCK_ON); ++ } ++} ++ ++static bool ++mtk_nand_pio_ready(void) ++{ ++ int count = 0; ++ while (!(DRV_Reg16(NFI_PIO_DIRDY_REG16) & 1)) { ++ count++; ++ if (count > 0xffff) { ++ printk("PIO_DIRDY timeout\n"); ++ return false; ++ } ++ } ++ ++ return true; ++} ++ ++static bool ++mtk_nand_set_command(u16 command) ++{ ++ mb(); ++ DRV_WriteReg16(NFI_CMD_REG16, command); ++ return mtk_nand_status_ready(STA_CMD_STATE); ++} ++ ++static bool ++mtk_nand_set_address(u32 u4ColAddr, u32 u4RowAddr, u16 u2ColNOB, u16 u2RowNOB) ++{ ++ mb(); ++ DRV_WriteReg32(NFI_COLADDR_REG32, u4ColAddr); ++ DRV_WriteReg32(NFI_ROWADDR_REG32, u4RowAddr); ++ DRV_WriteReg16(NFI_ADDRNOB_REG16, u2ColNOB | (u2RowNOB << ADDR_ROW_NOB_SHIFT)); ++ return mtk_nand_status_ready(STA_ADDR_STATE); ++} ++ ++static void mtk_nfc_cmd_ctrl(struct mtd_info *mtd, int dat, unsigned int ctrl) ++{ ++ if (ctrl & NAND_ALE) { ++ mtk_nand_set_address(dat, 0, 1, 0); ++ } else if (ctrl & NAND_CLE) { ++ mtk_nand_reset(); ++ mtk_nand_set_mode(0x6000); ++ mtk_nand_set_command(dat); ++ } ++} ++ ++static bool ++mtk_nand_check_RW_count(u16 u2WriteSize) ++{ ++ u32 timeout = 0xFFFF; ++ u16 u2SecNum = u2WriteSize >> 9; ++ ++ while (ADDRCNTR_CNTR(DRV_Reg16(NFI_ADDRCNTR_REG16)) < u2SecNum) { ++ timeout--; ++ if (0 == timeout) { ++ printk(KERN_INFO "[%s] timeout\n", __FUNCTION__); ++ return false; ++ } ++ } ++ return true; ++} ++ ++static bool ++mtk_nand_ready_for_read(struct nand_chip *nand, u32 u4RowAddr, u32 u4ColAddr, bool full, u8 * buf) ++{ ++ /* Reset NFI HW internal state machine and flush NFI in/out FIFO */ ++ bool bRet = false; ++ u16 sec_num = 1 << (nand->page_shift - 9); ++ u32 col_addr = u4ColAddr; ++ u32 colnob = 2, rownob = devinfo.addr_cycle - 2; ++ if (nand->options & NAND_BUSWIDTH_16) ++ col_addr /= 2; ++ ++ if (!mtk_nand_reset()) ++ goto cleanup; ++ if (g_bHwEcc) { ++ NFI_SET_REG16(NFI_CNFG_REG16, CNFG_HW_ECC_EN); ++ } else { ++ NFI_CLN_REG16(NFI_CNFG_REG16, CNFG_HW_ECC_EN); ++ } ++ ++ mtk_nand_set_mode(CNFG_OP_READ); ++ NFI_SET_REG16(NFI_CNFG_REG16, CNFG_READ_EN); ++ DRV_WriteReg16(NFI_CON_REG16, sec_num << CON_NFI_SEC_SHIFT); ++ ++ if (full) { ++ NFI_CLN_REG16(NFI_CNFG_REG16, CNFG_AHB); ++ ++ if (g_bHwEcc) ++ NFI_SET_REG16(NFI_CNFG_REG16, CNFG_HW_ECC_EN); ++ else ++ NFI_CLN_REG16(NFI_CNFG_REG16, CNFG_HW_ECC_EN); ++ } else { ++ NFI_CLN_REG16(NFI_CNFG_REG16, CNFG_HW_ECC_EN); ++ NFI_CLN_REG16(NFI_CNFG_REG16, CNFG_AHB); ++ } ++ ++ mtk_nand_set_autoformat(full); ++ if (full) ++ if (g_bHwEcc) ++ ECC_Decode_Start(); ++ if (!mtk_nand_set_command(NAND_CMD_READ0)) ++ goto cleanup; ++ if (!mtk_nand_set_address(col_addr, u4RowAddr, colnob, rownob)) ++ goto cleanup; ++ if (!mtk_nand_set_command(NAND_CMD_READSTART)) ++ goto cleanup; ++ if (!mtk_nand_status_ready(STA_NAND_BUSY)) ++ goto cleanup; ++ ++ bRet = true; ++ ++cleanup: ++ return bRet; ++} ++ ++static bool ++mtk_nand_ready_for_write(struct nand_chip *nand, u32 u4RowAddr, u32 col_addr, bool full, u8 * buf) ++{ ++ bool bRet = false; ++ u32 sec_num = 1 << (nand->page_shift - 9); ++ u32 colnob = 2, rownob = devinfo.addr_cycle - 2; ++ if (nand->options & NAND_BUSWIDTH_16) ++ col_addr /= 2; ++ ++ /* Reset NFI HW internal state machine and flush NFI in/out FIFO */ ++ if (!mtk_nand_reset()) ++ return false; ++ ++ mtk_nand_set_mode(CNFG_OP_PRGM); ++ ++ NFI_CLN_REG16(NFI_CNFG_REG16, CNFG_READ_EN); ++ ++ DRV_WriteReg16(NFI_CON_REG16, sec_num << CON_NFI_SEC_SHIFT); ++ ++ if (full) { ++ NFI_CLN_REG16(NFI_CNFG_REG16, CNFG_AHB); ++ if (g_bHwEcc) ++ NFI_SET_REG16(NFI_CNFG_REG16, CNFG_HW_ECC_EN); ++ else ++ NFI_CLN_REG16(NFI_CNFG_REG16, CNFG_HW_ECC_EN); ++ } else { ++ NFI_CLN_REG16(NFI_CNFG_REG16, CNFG_HW_ECC_EN); ++ NFI_CLN_REG16(NFI_CNFG_REG16, CNFG_AHB); ++ } ++ ++ mtk_nand_set_autoformat(full); ++ ++ if (full) ++ if (g_bHwEcc) ++ ECC_Encode_Start(); ++ ++ if (!mtk_nand_set_command(NAND_CMD_SEQIN)) ++ goto cleanup; ++ //1 FIXED ME: For Any Kind of AddrCycle ++ if (!mtk_nand_set_address(col_addr, u4RowAddr, colnob, rownob)) ++ goto cleanup; ++ ++ if (!mtk_nand_status_ready(STA_NAND_BUSY)) ++ goto cleanup; ++ ++ bRet = true; ++ ++cleanup: ++ return bRet; ++} ++ ++static bool ++mtk_nand_check_dececc_done(u32 u4SecNum) ++{ ++ u32 timeout, dec_mask; ++ ++ timeout = 0xffff; ++ dec_mask = (1 << u4SecNum) - 1; ++ while ((dec_mask != DRV_Reg(ECC_DECDONE_REG16)) && timeout > 0) ++ timeout--; ++ if (timeout == 0) { ++ MSG(VERIFY, "ECC_DECDONE: timeout\n"); ++ return false; ++ } ++ return true; ++} ++ ++static bool ++mtk_nand_mcu_read_data(u8 * buf, u32 length) ++{ ++ int timeout = 0xffff; ++ u32 i; ++ u32 *buf32 = (u32 *) buf; ++ if ((u32) buf % 4 || length % 4) ++ NFI_SET_REG16(NFI_CNFG_REG16, CNFG_BYTE_RW); ++ else ++ NFI_CLN_REG16(NFI_CNFG_REG16, CNFG_BYTE_RW); ++ ++ //DRV_WriteReg32(NFI_STRADDR_REG32, 0); ++ mb(); ++ NFI_SET_REG16(NFI_CON_REG16, CON_NFI_BRD); ++ ++ if ((u32) buf % 4 || length % 4) { ++ for (i = 0; (i < (length)) && (timeout > 0);) { ++ if (DRV_Reg16(NFI_PIO_DIRDY_REG16) & 1) { ++ *buf++ = (u8) DRV_Reg32(NFI_DATAR_REG32); ++ i++; ++ } else { ++ timeout--; ++ } ++ if (0 == timeout) { ++ printk(KERN_ERR "[%s] timeout\n", __FUNCTION__); ++ dump_nfi(); ++ return false; ++ } ++ } ++ } else { ++ for (i = 0; (i < (length >> 2)) && (timeout > 0);) { ++ if (DRV_Reg16(NFI_PIO_DIRDY_REG16) & 1) { ++ *buf32++ = DRV_Reg32(NFI_DATAR_REG32); ++ i++; ++ } else { ++ timeout--; ++ } ++ if (0 == timeout) { ++ printk(KERN_ERR "[%s] timeout\n", __FUNCTION__); ++ dump_nfi(); ++ return false; ++ } ++ } ++ } ++ return true; ++} ++ ++static bool ++mtk_nand_read_page_data(struct mtd_info *mtd, u8 * pDataBuf, u32 u4Size) ++{ ++ return mtk_nand_mcu_read_data(pDataBuf, u4Size); ++} ++ ++static bool ++mtk_nand_mcu_write_data(struct mtd_info *mtd, const u8 * buf, u32 length) ++{ ++ u32 timeout = 0xFFFF; ++ u32 i; ++ u32 *pBuf32; ++ NFI_CLN_REG16(NFI_CNFG_REG16, CNFG_BYTE_RW); ++ mb(); ++ NFI_SET_REG16(NFI_CON_REG16, CON_NFI_BWR); ++ pBuf32 = (u32 *) buf; ++ ++ if ((u32) buf % 4 || length % 4) ++ NFI_SET_REG16(NFI_CNFG_REG16, CNFG_BYTE_RW); ++ else ++ NFI_CLN_REG16(NFI_CNFG_REG16, CNFG_BYTE_RW); ++ ++ if ((u32) buf % 4 || length % 4) { ++ for (i = 0; (i < (length)) && (timeout > 0);) { ++ if (DRV_Reg16(NFI_PIO_DIRDY_REG16) & 1) { ++ DRV_WriteReg32(NFI_DATAW_REG32, *buf++); ++ i++; ++ } else { ++ timeout--; ++ } ++ if (0 == timeout) { ++ printk(KERN_ERR "[%s] timeout\n", __FUNCTION__); ++ dump_nfi(); ++ return false; ++ } ++ } ++ } else { ++ for (i = 0; (i < (length >> 2)) && (timeout > 0);) { ++ if (DRV_Reg16(NFI_PIO_DIRDY_REG16) & 1) { ++ DRV_WriteReg32(NFI_DATAW_REG32, *pBuf32++); ++ i++; ++ } else { ++ timeout--; ++ } ++ if (0 == timeout) { ++ printk(KERN_ERR "[%s] timeout\n", __FUNCTION__); ++ dump_nfi(); ++ return false; ++ } ++ } ++ } ++ ++ return true; ++} ++ ++static bool ++mtk_nand_write_page_data(struct mtd_info *mtd, u8 * buf, u32 size) ++{ ++ return mtk_nand_mcu_write_data(mtd, buf, size); ++} ++ ++static void ++mtk_nand_read_fdm_data(u8 * pDataBuf, u32 u4SecNum) ++{ ++ u32 i; ++ u32 *pBuf32 = (u32 *) pDataBuf; ++ ++ if (pBuf32) { ++ for (i = 0; i < u4SecNum; ++i) { ++ *pBuf32++ = DRV_Reg32(NFI_FDM0L_REG32 + (i << 1)); ++ *pBuf32++ = DRV_Reg32(NFI_FDM0M_REG32 + (i << 1)); ++ } ++ } ++} ++ ++static u8 fdm_buf[64]; ++static void ++mtk_nand_write_fdm_data(struct nand_chip *chip, u8 * pDataBuf, u32 u4SecNum) ++{ ++ u32 i, j; ++ u8 checksum = 0; ++ bool empty = true; ++ struct nand_oobfree *free_entry; ++ u32 *pBuf32; ++ ++ memcpy(fdm_buf, pDataBuf, u4SecNum * 8); ++ ++ free_entry = layout->oobfree; ++ for (i = 0; i < MTD_MAX_OOBFREE_ENTRIES && free_entry[i].length; i++) { ++ for (j = 0; j < free_entry[i].length; j++) { ++ if (pDataBuf[free_entry[i].offset + j] != 0xFF) ++ empty = false; ++ checksum ^= pDataBuf[free_entry[i].offset + j]; ++ } ++ } ++ ++ if (!empty) { ++ fdm_buf[free_entry[i - 1].offset + free_entry[i - 1].length] = checksum; ++ } ++ ++ pBuf32 = (u32 *) fdm_buf; ++ for (i = 0; i < u4SecNum; ++i) { ++ DRV_WriteReg32(NFI_FDM0L_REG32 + (i << 1), *pBuf32++); ++ DRV_WriteReg32(NFI_FDM0M_REG32 + (i << 1), *pBuf32++); ++ } ++} ++ ++static void ++mtk_nand_stop_read(void) ++{ ++ NFI_CLN_REG16(NFI_CON_REG16, CON_NFI_BRD); ++ mtk_nand_reset(); ++ if (g_bHwEcc) ++ ECC_Decode_End(); ++ DRV_WriteReg16(NFI_INTR_EN_REG16, 0); ++} ++ ++static void ++mtk_nand_stop_write(void) ++{ ++ NFI_CLN_REG16(NFI_CON_REG16, CON_NFI_BWR); ++ if (g_bHwEcc) ++ ECC_Encode_End(); ++ DRV_WriteReg16(NFI_INTR_EN_REG16, 0); ++} ++ ++bool ++mtk_nand_exec_read_page(struct mtd_info *mtd, u32 u4RowAddr, u32 u4PageSize, u8 * pPageBuf, u8 * pFDMBuf) ++{ ++ u8 *buf; ++ bool bRet = true; ++ struct nand_chip *nand = mtd->priv; ++ u32 u4SecNum = u4PageSize >> 9; ++ ++ buf = pPageBuf; ++ if (mtk_nand_ready_for_read(nand, u4RowAddr, 0, true, buf)) { ++ int j; ++ for (j = 0 ; j < u4SecNum; j++) { ++ if (!mtk_nand_read_page_data(mtd, buf+j*512, 512)) ++ bRet = false; ++ if(g_bHwEcc && !mtk_nand_check_dececc_done(j+1)) ++ bRet = false; ++ if(g_bHwEcc && !mtk_nand_check_bch_error(mtd, buf+j*512, j, u4RowAddr)) ++ bRet = false; ++ } ++ if (!mtk_nand_status_ready(STA_NAND_BUSY)) ++ bRet = false; ++ ++ mtk_nand_read_fdm_data(pFDMBuf, u4SecNum); ++ mtk_nand_stop_read(); ++ } ++ ++ return bRet; ++} ++ ++int ++mtk_nand_exec_write_page(struct mtd_info *mtd, u32 u4RowAddr, u32 u4PageSize, u8 * pPageBuf, u8 * pFDMBuf) ++{ ++ struct nand_chip *chip = mtd->priv; ++ u32 u4SecNum = u4PageSize >> 9; ++ u8 *buf; ++ u8 status; ++ ++ MSG(WRITE, "mtk_nand_exec_write_page, page: 0x%x\n", u4RowAddr); ++ ++ buf = pPageBuf; ++ ++ if (mtk_nand_ready_for_write(chip, u4RowAddr, 0, true, buf)) { ++ mtk_nand_write_fdm_data(chip, pFDMBuf, u4SecNum); ++ (void)mtk_nand_write_page_data(mtd, buf, u4PageSize); ++ (void)mtk_nand_check_RW_count(u4PageSize); ++ mtk_nand_stop_write(); ++ (void)mtk_nand_set_command(NAND_CMD_PAGEPROG); ++ while (DRV_Reg32(NFI_STA_REG32) & STA_NAND_BUSY) ; ++ } ++ ++ status = chip->waitfunc(mtd, chip); ++ if (status & NAND_STATUS_FAIL) ++ return -EIO; ++ return 0; ++} ++ ++static int ++get_start_end_block(struct mtd_info *mtd, int block, int *start_blk, int *end_blk) ++{ ++ struct nand_chip *chip = mtd->priv; ++ int i; ++ ++ *start_blk = 0; ++ for (i = 0; i <= part_num; i++) ++ { ++ if (i == part_num) ++ { ++ // try the last reset partition ++ *end_blk = (chip->chipsize >> chip->phys_erase_shift) - 1; ++ if (*start_blk <= *end_blk) ++ { ++ if ((block >= *start_blk) && (block <= *end_blk)) ++ break; ++ } ++ } ++ // skip All partition entry ++ else if (g_pasStatic_Partition[i].size == MTDPART_SIZ_FULL) ++ { ++ continue; ++ } ++ *end_blk = *start_blk + (g_pasStatic_Partition[i].size >> chip->phys_erase_shift) - 1; ++ if ((block >= *start_blk) && (block <= *end_blk)) ++ break; ++ *start_blk = *end_blk + 1; ++ } ++ if (*start_blk > *end_blk) ++ { ++ return -1; ++ } ++ return 0; ++} ++ ++static int ++block_remap(struct mtd_info *mtd, int block) ++{ ++ struct nand_chip *chip = mtd->priv; ++ int start_blk, end_blk; ++ int j, block_offset; ++ int bad_block = 0; ++ ++ if (chip->bbt == NULL) { ++ printk("ERROR!! no bbt table for block_remap\n"); ++ return -1; ++ } ++ ++ if (get_start_end_block(mtd, block, &start_blk, &end_blk) < 0) { ++ printk("ERROR!! can not find start_blk and end_blk\n"); ++ return -1; ++ } ++ ++ block_offset = block - start_blk; ++ for (j = start_blk; j <= end_blk;j++) { ++ if (((chip->bbt[j >> 2] >> ((j<<1) & 0x6)) & 0x3) == 0x0) { ++ if (!block_offset) ++ break; ++ block_offset--; ++ } else { ++ bad_block++; ++ } ++ } ++ if (j <= end_blk) { ++ return j; ++ } else { ++ // remap to the bad block ++ for (j = end_blk; bad_block > 0; j--) ++ { ++ if (((chip->bbt[j >> 2] >> ((j<<1) & 0x6)) & 0x3) != 0x0) ++ { ++ bad_block--; ++ if (bad_block <= block_offset) ++ return j; ++ } ++ } ++ } ++ ++ printk("Error!! block_remap error\n"); ++ return -1; ++} ++ ++int ++check_block_remap(struct mtd_info *mtd, int block) ++{ ++ if (shift_on_bbt) ++ return block_remap(mtd, block); ++ else ++ return block; ++} ++EXPORT_SYMBOL(check_block_remap); ++ ++ ++static int ++write_next_on_fail(struct mtd_info *mtd, char *write_buf, int page, int * to_blk) ++{ ++ struct nand_chip *chip = mtd->priv; ++ int i, j, to_page = 0, first_page; ++ char *buf, *oob; ++ int start_blk = 0, end_blk; ++ int mapped_block; ++ int page_per_block_bit = chip->phys_erase_shift - chip->page_shift; ++ int block = page >> page_per_block_bit; ++ ++ // find next available block in the same MTD partition ++ mapped_block = block_remap(mtd, block); ++ if (mapped_block == -1) ++ return NAND_STATUS_FAIL; ++ ++ get_start_end_block(mtd, block, &start_blk, &end_blk); ++ ++ buf = kzalloc(mtd->writesize + mtd->oobsize, GFP_KERNEL | GFP_DMA); ++ if (buf == NULL) ++ return -1; ++ ++ oob = buf + mtd->writesize; ++ for ((*to_blk) = block + 1; (*to_blk) <= end_blk ; (*to_blk)++) { ++ if (nand_bbt_get(mtd, (*to_blk) << page_per_block_bit) == 0) { ++ int status; ++ status = mtk_nand_erase_hw(mtd, (*to_blk) << page_per_block_bit); ++ if (status & NAND_STATUS_FAIL) { ++ mtk_nand_block_markbad_hw(mtd, (*to_blk) << chip->phys_erase_shift); ++ nand_bbt_set(mtd, (*to_blk) << page_per_block_bit, 0x3); ++ } else { ++ /* good block */ ++ to_page = (*to_blk) << page_per_block_bit; ++ break; ++ } ++ } ++ } ++ ++ if (!to_page) { ++ kfree(buf); ++ return -1; ++ } ++ ++ first_page = (page >> page_per_block_bit) << page_per_block_bit; ++ for (i = 0; i < (1 << page_per_block_bit); i++) { ++ if ((first_page + i) != page) { ++ mtk_nand_read_oob_hw(mtd, chip, (first_page+i)); ++ for (j = 0; j < mtd->oobsize; j++) ++ if (chip->oob_poi[j] != (unsigned char)0xff) ++ break; ++ if (j < mtd->oobsize) { ++ mtk_nand_exec_read_page(mtd, (first_page+i), mtd->writesize, buf, oob); ++ memset(oob, 0xff, mtd->oobsize); ++ if (mtk_nand_exec_write_page(mtd, to_page + i, mtd->writesize, (u8 *)buf, oob) != 0) { ++ int ret, new_blk = 0; ++ nand_bbt_set(mtd, to_page, 0x3); ++ ret = write_next_on_fail(mtd, buf, to_page + i, &new_blk); ++ if (ret) { ++ kfree(buf); ++ mtk_nand_block_markbad_hw(mtd, to_page << chip->page_shift); ++ return ret; ++ } ++ mtk_nand_block_markbad_hw(mtd, to_page << chip->page_shift); ++ *to_blk = new_blk; ++ to_page = ((*to_blk) << page_per_block_bit); ++ } ++ } ++ } else { ++ memset(chip->oob_poi, 0xff, mtd->oobsize); ++ if (mtk_nand_exec_write_page(mtd, to_page + i, mtd->writesize, (u8 *)write_buf, chip->oob_poi) != 0) { ++ int ret, new_blk = 0; ++ nand_bbt_set(mtd, to_page, 0x3); ++ ret = write_next_on_fail(mtd, write_buf, to_page + i, &new_blk); ++ if (ret) { ++ kfree(buf); ++ mtk_nand_block_markbad_hw(mtd, to_page << chip->page_shift); ++ return ret; ++ } ++ mtk_nand_block_markbad_hw(mtd, to_page << chip->page_shift); ++ *to_blk = new_blk; ++ to_page = ((*to_blk) << page_per_block_bit); ++ } ++ } ++ } ++ ++ kfree(buf); ++ ++ return 0; ++} ++ ++static int ++mtk_nand_write_page(struct mtd_info *mtd, struct nand_chip *chip, uint32_t offset, ++ int data_len, const u8 * buf, int oob_required, int page, int raw) ++{ ++ int page_per_block = 1 << (chip->phys_erase_shift - chip->page_shift); ++ int block = page / page_per_block; ++ u16 page_in_block = page % page_per_block; ++ int mapped_block = block; ++ ++#if defined(MTK_NAND_BMT) ++ mapped_block = get_mapping_block_index(block); ++ // write bad index into oob ++ if (mapped_block != block) ++ set_bad_index_to_oob(chip->oob_poi, block); ++ else ++ set_bad_index_to_oob(chip->oob_poi, FAKE_INDEX); ++#else ++ if (shift_on_bbt) { ++ mapped_block = block_remap(mtd, block); ++ if (mapped_block == -1) ++ return NAND_STATUS_FAIL; ++ if (nand_bbt_get(mtd, mapped_block << (chip->phys_erase_shift - chip->page_shift)) != 0x0) ++ return NAND_STATUS_FAIL; ++ } ++#endif ++ do { ++ if (mtk_nand_exec_write_page(mtd, page_in_block + mapped_block * page_per_block, mtd->writesize, (u8 *)buf, chip->oob_poi)) { ++ MSG(INIT, "write fail at block: 0x%x, page: 0x%x\n", mapped_block, page_in_block); ++#if defined(MTK_NAND_BMT) ++ if (update_bmt((page_in_block + mapped_block * page_per_block) << chip->page_shift, UPDATE_WRITE_FAIL, (u8 *) buf, chip->oob_poi)) { ++ MSG(INIT, "Update BMT success\n"); ++ return 0; ++ } else { ++ MSG(INIT, "Update BMT fail\n"); ++ return -EIO; ++ } ++#else ++ { ++ int new_blk; ++ nand_bbt_set(mtd, page_in_block + mapped_block * page_per_block, 0x3); ++ if (write_next_on_fail(mtd, (char *)buf, page_in_block + mapped_block * page_per_block, &new_blk) != 0) ++ { ++ mtk_nand_block_markbad_hw(mtd, (page_in_block + mapped_block * page_per_block) << chip->page_shift); ++ return NAND_STATUS_FAIL; ++ } ++ mtk_nand_block_markbad_hw(mtd, (page_in_block + mapped_block * page_per_block) << chip->page_shift); ++ break; ++ } ++#endif ++ } else ++ break; ++ } while(1); ++ ++ return 0; ++} ++ ++static void ++mtk_nand_command_bp(struct mtd_info *mtd, unsigned int command, int column, int page_addr) ++{ ++ struct nand_chip *nand = mtd->priv; ++ ++ switch (command) { ++ case NAND_CMD_SEQIN: ++ memset(g_kCMD.au1OOB, 0xFF, sizeof(g_kCMD.au1OOB)); ++ g_kCMD.pDataBuf = NULL; ++ g_kCMD.u4RowAddr = page_addr; ++ g_kCMD.u4ColAddr = column; ++ break; ++ ++ case NAND_CMD_PAGEPROG: ++ if (g_kCMD.pDataBuf || (0xFF != g_kCMD.au1OOB[nand_badblock_offset])) { ++ u8 *pDataBuf = g_kCMD.pDataBuf ? g_kCMD.pDataBuf : nand->buffers->databuf; ++ mtk_nand_exec_write_page(mtd, g_kCMD.u4RowAddr, mtd->writesize, pDataBuf, g_kCMD.au1OOB); ++ g_kCMD.u4RowAddr = (u32) - 1; ++ g_kCMD.u4OOBRowAddr = (u32) - 1; ++ } ++ break; ++ ++ case NAND_CMD_READOOB: ++ g_kCMD.u4RowAddr = page_addr; ++ g_kCMD.u4ColAddr = column + mtd->writesize; ++ break; ++ ++ case NAND_CMD_READ0: ++ g_kCMD.u4RowAddr = page_addr; ++ g_kCMD.u4ColAddr = column; ++ break; ++ ++ case NAND_CMD_ERASE1: ++ nand->state=FL_ERASING; ++ (void)mtk_nand_reset(); ++ mtk_nand_set_mode(CNFG_OP_ERASE); ++ (void)mtk_nand_set_command(NAND_CMD_ERASE1); ++ (void)mtk_nand_set_address(0, page_addr, 0, devinfo.addr_cycle - 2); ++ break; ++ ++ case NAND_CMD_ERASE2: ++ (void)mtk_nand_set_command(NAND_CMD_ERASE2); ++ while (DRV_Reg32(NFI_STA_REG32) & STA_NAND_BUSY) ++ ; ++ break; ++ ++ case NAND_CMD_STATUS: ++ (void)mtk_nand_reset(); ++ NFI_CLN_REG16(NFI_CNFG_REG16, CNFG_BYTE_RW); ++ mtk_nand_set_mode(CNFG_OP_SRD); ++ mtk_nand_set_mode(CNFG_READ_EN); ++ NFI_CLN_REG16(NFI_CNFG_REG16, CNFG_AHB); ++ NFI_CLN_REG16(NFI_CNFG_REG16, CNFG_HW_ECC_EN); ++ (void)mtk_nand_set_command(NAND_CMD_STATUS); ++ NFI_CLN_REG16(NFI_CON_REG16, CON_NFI_NOB_MASK); ++ mb(); ++ DRV_WriteReg16(NFI_CON_REG16, CON_NFI_SRD | (1 << CON_NFI_NOB_SHIFT)); ++ g_bcmdstatus = true; ++ break; ++ ++ case NAND_CMD_RESET: ++ (void)mtk_nand_reset(); ++ DRV_WriteReg16(NFI_INTR_EN_REG16, INTR_RST_DONE_EN); ++ (void)mtk_nand_set_command(NAND_CMD_RESET); ++ DRV_WriteReg16(NFI_BASE+0x44, 0xF1); ++ while(!(DRV_Reg16(NFI_INTR_REG16)&INTR_RST_DONE_EN)) ++ ; ++ break; ++ ++ case NAND_CMD_READID: ++ mtk_nand_reset(); ++ /* Disable HW ECC */ ++ NFI_CLN_REG16(NFI_CNFG_REG16, CNFG_HW_ECC_EN); ++ NFI_CLN_REG16(NFI_CNFG_REG16, CNFG_AHB); ++ NFI_SET_REG16(NFI_CNFG_REG16, CNFG_READ_EN | CNFG_BYTE_RW); ++ (void)mtk_nand_reset(); ++ mb(); ++ mtk_nand_set_mode(CNFG_OP_SRD); ++ (void)mtk_nand_set_command(NAND_CMD_READID); ++ (void)mtk_nand_set_address(0, 0, 1, 0); ++ DRV_WriteReg16(NFI_CON_REG16, CON_NFI_SRD); ++ while (DRV_Reg32(NFI_STA_REG32) & STA_DATAR_STATE) ++ ; ++ break; ++ ++ default: ++ BUG(); ++ break; ++ } ++} ++ ++static void ++mtk_nand_select_chip(struct mtd_info *mtd, int chip) ++{ ++ if ((chip == -1) && (false == g_bInitDone)) { ++ struct nand_chip *nand = mtd->priv; ++ struct mtk_nand_host *host = nand->priv; ++ struct mtk_nand_host_hw *hw = host->hw; ++ u32 spare_per_sector = mtd->oobsize / (mtd->writesize / 512); ++ u32 ecc_bit = 4; ++ u32 spare_bit = PAGEFMT_SPARE_16; ++ ++ if (spare_per_sector >= 28) { ++ spare_bit = PAGEFMT_SPARE_28; ++ ecc_bit = 12; ++ spare_per_sector = 28; ++ } else if (spare_per_sector >= 27) { ++ spare_bit = PAGEFMT_SPARE_27; ++ ecc_bit = 8; ++ spare_per_sector = 27; ++ } else if (spare_per_sector >= 26) { ++ spare_bit = PAGEFMT_SPARE_26; ++ ecc_bit = 8; ++ spare_per_sector = 26; ++ } else if (spare_per_sector >= 16) { ++ spare_bit = PAGEFMT_SPARE_16; ++ ecc_bit = 4; ++ spare_per_sector = 16; ++ } else { ++ MSG(INIT, "[NAND]: NFI not support oobsize: %x\n", spare_per_sector); ++ ASSERT(0); ++ } ++ mtd->oobsize = spare_per_sector*(mtd->writesize/512); ++ MSG(INIT, "[NAND]select ecc bit:%d, sparesize :%d spare_per_sector=%d\n",ecc_bit,mtd->oobsize,spare_per_sector); ++ /* Setup PageFormat */ ++ if (4096 == mtd->writesize) { ++ NFI_SET_REG16(NFI_PAGEFMT_REG16, (spare_bit << PAGEFMT_SPARE_SHIFT) | PAGEFMT_4K); ++ nand->cmdfunc = mtk_nand_command_bp; ++ } else if (2048 == mtd->writesize) { ++ NFI_SET_REG16(NFI_PAGEFMT_REG16, (spare_bit << PAGEFMT_SPARE_SHIFT) | PAGEFMT_2K); ++ nand->cmdfunc = mtk_nand_command_bp; ++ } ++ ECC_Config(hw,ecc_bit); ++ g_bInitDone = true; ++ } ++ switch (chip) { ++ case -1: ++ break; ++ case 0: ++ case 1: ++ /* Jun Shen, 2011.04.13 */ ++ /* Note: MT6577 EVB NAND is mounted on CS0, but FPGA is CS1 */ ++ DRV_WriteReg16(NFI_CSEL_REG16, chip); ++ /* Jun Shen, 2011.04.13 */ ++ break; ++ } ++} ++ ++static uint8_t ++mtk_nand_read_byte(struct mtd_info *mtd) ++{ ++ uint8_t retval = 0; ++ ++ if (!mtk_nand_pio_ready()) { ++ printk("pio ready timeout\n"); ++ retval = false; ++ } ++ ++ if (g_bcmdstatus) { ++ retval = DRV_Reg8(NFI_DATAR_REG32); ++ NFI_CLN_REG16(NFI_CON_REG16, CON_NFI_NOB_MASK); ++ mtk_nand_reset(); ++ if (g_bHwEcc) { ++ NFI_SET_REG16(NFI_CNFG_REG16, CNFG_HW_ECC_EN); ++ } else { ++ NFI_CLN_REG16(NFI_CNFG_REG16, CNFG_HW_ECC_EN); ++ } ++ g_bcmdstatus = false; ++ } else ++ retval = DRV_Reg8(NFI_DATAR_REG32); ++ ++ return retval; ++} ++ ++static void ++mtk_nand_read_buf(struct mtd_info *mtd, uint8_t * buf, int len) ++{ ++ struct nand_chip *nand = (struct nand_chip *)mtd->priv; ++ struct NAND_CMD *pkCMD = &g_kCMD; ++ u32 u4ColAddr = pkCMD->u4ColAddr; ++ u32 u4PageSize = mtd->writesize; ++ ++ if (u4ColAddr < u4PageSize) { ++ if ((u4ColAddr == 0) && (len >= u4PageSize)) { ++ mtk_nand_exec_read_page(mtd, pkCMD->u4RowAddr, u4PageSize, buf, pkCMD->au1OOB); ++ if (len > u4PageSize) { ++ u32 u4Size = min(len - u4PageSize, sizeof(pkCMD->au1OOB)); ++ memcpy(buf + u4PageSize, pkCMD->au1OOB, u4Size); ++ } ++ } else { ++ mtk_nand_exec_read_page(mtd, pkCMD->u4RowAddr, u4PageSize, nand->buffers->databuf, pkCMD->au1OOB); ++ memcpy(buf, nand->buffers->databuf + u4ColAddr, len); ++ } ++ pkCMD->u4OOBRowAddr = pkCMD->u4RowAddr; ++ } else { ++ u32 u4Offset = u4ColAddr - u4PageSize; ++ u32 u4Size = min(len - u4Offset, sizeof(pkCMD->au1OOB)); ++ if (pkCMD->u4OOBRowAddr != pkCMD->u4RowAddr) { ++ mtk_nand_exec_read_page(mtd, pkCMD->u4RowAddr, u4PageSize, nand->buffers->databuf, pkCMD->au1OOB); ++ pkCMD->u4OOBRowAddr = pkCMD->u4RowAddr; ++ } ++ memcpy(buf, pkCMD->au1OOB + u4Offset, u4Size); ++ } ++ pkCMD->u4ColAddr += len; ++} ++ ++static void ++mtk_nand_write_buf(struct mtd_info *mtd, const uint8_t * buf, int len) ++{ ++ struct NAND_CMD *pkCMD = &g_kCMD; ++ u32 u4ColAddr = pkCMD->u4ColAddr; ++ u32 u4PageSize = mtd->writesize; ++ int i4Size, i; ++ ++ if (u4ColAddr >= u4PageSize) { ++ u32 u4Offset = u4ColAddr - u4PageSize; ++ u8 *pOOB = pkCMD->au1OOB + u4Offset; ++ i4Size = min(len, (int)(sizeof(pkCMD->au1OOB) - u4Offset)); ++ for (i = 0; i < i4Size; i++) { ++ pOOB[i] &= buf[i]; ++ } ++ } else { ++ pkCMD->pDataBuf = (u8 *) buf; ++ } ++ ++ pkCMD->u4ColAddr += len; ++} ++ ++static int ++mtk_nand_write_page_hwecc(struct mtd_info *mtd, struct nand_chip *chip, const uint8_t * buf, int oob_required, int page) ++{ ++ mtk_nand_write_buf(mtd, buf, mtd->writesize); ++ mtk_nand_write_buf(mtd, chip->oob_poi, mtd->oobsize); ++ return 0; ++} ++ ++static int ++mtk_nand_read_page_hwecc(struct mtd_info *mtd, struct nand_chip *chip, uint8_t * buf, int oob_required, int page) ++{ ++ struct NAND_CMD *pkCMD = &g_kCMD; ++ u32 u4ColAddr = pkCMD->u4ColAddr; ++ u32 u4PageSize = mtd->writesize; ++ ++ if (u4ColAddr == 0) { ++ mtk_nand_exec_read_page(mtd, pkCMD->u4RowAddr, u4PageSize, buf, chip->oob_poi); ++ pkCMD->u4ColAddr += u4PageSize + mtd->oobsize; ++ } ++ ++ return 0; ++} ++ ++static int ++mtk_nand_read_page(struct mtd_info *mtd, struct nand_chip *chip, u8 * buf, int page) ++{ ++ int page_per_block = 1 << (chip->phys_erase_shift - chip->page_shift); ++ int block = page / page_per_block; ++ u16 page_in_block = page % page_per_block; ++ int mapped_block = block; ++ ++#if defined (MTK_NAND_BMT) ++ mapped_block = get_mapping_block_index(block); ++ if (mtk_nand_exec_read_page(mtd, page_in_block + mapped_block * page_per_block, ++ mtd->writesize, buf, chip->oob_poi)) ++ return 0; ++#else ++ if (shift_on_bbt) { ++ mapped_block = block_remap(mtd, block); ++ if (mapped_block == -1) ++ return NAND_STATUS_FAIL; ++ if (nand_bbt_get(mtd, mapped_block << (chip->phys_erase_shift - chip->page_shift)) != 0x0) ++ return NAND_STATUS_FAIL; ++ } ++ ++ if (mtk_nand_exec_read_page(mtd, page_in_block + mapped_block * page_per_block, mtd->writesize, buf, chip->oob_poi)) ++ return 0; ++ else ++ return -EIO; ++#endif ++} ++ ++int ++mtk_nand_erase_hw(struct mtd_info *mtd, int page) ++{ ++ struct nand_chip *chip = (struct nand_chip *)mtd->priv; ++ ++ chip->cmdfunc(mtd, NAND_CMD_ERASE1, -1, page); ++ chip->cmdfunc(mtd, NAND_CMD_ERASE2, -1, -1); ++ ++ return chip->waitfunc(mtd, chip); ++} ++ ++static int ++mtk_nand_erase(struct mtd_info *mtd, int page) ++{ ++ // get mapping ++ struct nand_chip *chip = mtd->priv; ++ int page_per_block = 1 << (chip->phys_erase_shift - chip->page_shift); ++ int page_in_block = page % page_per_block; ++ int block = page / page_per_block; ++ int mapped_block = block; ++ ++#if defined(MTK_NAND_BMT) ++ mapped_block = get_mapping_block_index(block); ++#else ++ if (shift_on_bbt) { ++ mapped_block = block_remap(mtd, block); ++ if (mapped_block == -1) ++ return NAND_STATUS_FAIL; ++ if (nand_bbt_get(mtd, mapped_block << (chip->phys_erase_shift - chip->page_shift)) != 0x0) ++ return NAND_STATUS_FAIL; ++ } ++#endif ++ ++ do { ++ int status = mtk_nand_erase_hw(mtd, page_in_block + page_per_block * mapped_block); ++ ++ if (status & NAND_STATUS_FAIL) { ++#if defined (MTK_NAND_BMT) ++ if (update_bmt( (page_in_block + mapped_block * page_per_block) << chip->page_shift, ++ UPDATE_ERASE_FAIL, NULL, NULL)) ++ { ++ MSG(INIT, "Erase fail at block: 0x%x, update BMT success\n", mapped_block); ++ return 0; ++ } else { ++ MSG(INIT, "Erase fail at block: 0x%x, update BMT fail\n", mapped_block); ++ return NAND_STATUS_FAIL; ++ } ++#else ++ mtk_nand_block_markbad_hw(mtd, (page_in_block + mapped_block * page_per_block) << chip->page_shift); ++ nand_bbt_set(mtd, page_in_block + mapped_block * page_per_block, 0x3); ++ if (shift_on_bbt) { ++ mapped_block = block_remap(mtd, block); ++ if (mapped_block == -1) ++ return NAND_STATUS_FAIL; ++ if (nand_bbt_get(mtd, mapped_block << (chip->phys_erase_shift - chip->page_shift)) != 0x0) ++ return NAND_STATUS_FAIL; ++ } else ++ return NAND_STATUS_FAIL; ++#endif ++ } else ++ break; ++ } while(1); ++ ++ return 0; ++} ++ ++static int ++mtk_nand_read_oob_raw(struct mtd_info *mtd, uint8_t * buf, int page_addr, int len) ++{ ++ struct nand_chip *chip = (struct nand_chip *)mtd->priv; ++ u32 col_addr = 0; ++ u32 sector = 0; ++ int res = 0; ++ u32 colnob = 2, rawnob = devinfo.addr_cycle - 2; ++ int randomread = 0; ++ int read_len = 0; ++ int sec_num = 1<<(chip->page_shift-9); ++ int spare_per_sector = mtd->oobsize/sec_num; ++ ++ if (len > NAND_MAX_OOBSIZE || len % OOB_AVAI_PER_SECTOR || !buf) { ++ printk(KERN_WARNING "[%s] invalid parameter, len: %d, buf: %p\n", __FUNCTION__, len, buf); ++ return -EINVAL; ++ } ++ if (len > spare_per_sector) ++ randomread = 1; ++ if (!randomread || !(devinfo.advancedmode & RAMDOM_READ)) { ++ while (len > 0) { ++ read_len = min(len, spare_per_sector); ++ col_addr = NAND_SECTOR_SIZE + sector * (NAND_SECTOR_SIZE + spare_per_sector); // TODO: Fix this hard-code 16 ++ if (!mtk_nand_ready_for_read(chip, page_addr, col_addr, false, NULL)) { ++ printk(KERN_WARNING "mtk_nand_ready_for_read return failed\n"); ++ res = -EIO; ++ goto error; ++ } ++ if (!mtk_nand_mcu_read_data(buf + spare_per_sector * sector, read_len)) { ++ printk(KERN_WARNING "mtk_nand_mcu_read_data return failed\n"); ++ res = -EIO; ++ goto error; ++ } ++ mtk_nand_check_RW_count(read_len); ++ mtk_nand_stop_read(); ++ sector++; ++ len -= read_len; ++ } ++ } else { ++ col_addr = NAND_SECTOR_SIZE; ++ if (chip->options & NAND_BUSWIDTH_16) ++ col_addr /= 2; ++ if (!mtk_nand_reset()) ++ goto error; ++ mtk_nand_set_mode(0x6000); ++ NFI_SET_REG16(NFI_CNFG_REG16, CNFG_READ_EN); ++ DRV_WriteReg16(NFI_CON_REG16, 4 << CON_NFI_SEC_SHIFT); ++ ++ NFI_CLN_REG16(NFI_CNFG_REG16, CNFG_AHB); ++ NFI_CLN_REG16(NFI_CNFG_REG16, CNFG_HW_ECC_EN); ++ ++ mtk_nand_set_autoformat(false); ++ ++ if (!mtk_nand_set_command(NAND_CMD_READ0)) ++ goto error; ++ //1 FIXED ME: For Any Kind of AddrCycle ++ if (!mtk_nand_set_address(col_addr, page_addr, colnob, rawnob)) ++ goto error; ++ if (!mtk_nand_set_command(NAND_CMD_READSTART)) ++ goto error; ++ if (!mtk_nand_status_ready(STA_NAND_BUSY)) ++ goto error; ++ read_len = min(len, spare_per_sector); ++ if (!mtk_nand_mcu_read_data(buf + spare_per_sector * sector, read_len)) { ++ printk(KERN_WARNING "mtk_nand_mcu_read_data return failed first 16\n"); ++ res = -EIO; ++ goto error; ++ } ++ sector++; ++ len -= read_len; ++ mtk_nand_stop_read(); ++ while (len > 0) { ++ read_len = min(len, spare_per_sector); ++ if (!mtk_nand_set_command(0x05)) ++ goto error; ++ col_addr = NAND_SECTOR_SIZE + sector * (NAND_SECTOR_SIZE + spare_per_sector); ++ if (chip->options & NAND_BUSWIDTH_16) ++ col_addr /= 2; ++ DRV_WriteReg32(NFI_COLADDR_REG32, col_addr); ++ DRV_WriteReg16(NFI_ADDRNOB_REG16, 2); ++ DRV_WriteReg16(NFI_CON_REG16, 4 << CON_NFI_SEC_SHIFT); ++ if (!mtk_nand_status_ready(STA_ADDR_STATE)) ++ goto error; ++ if (!mtk_nand_set_command(0xE0)) ++ goto error; ++ if (!mtk_nand_status_ready(STA_NAND_BUSY)) ++ goto error; ++ if (!mtk_nand_mcu_read_data(buf + spare_per_sector * sector, read_len)) { ++ printk(KERN_WARNING "mtk_nand_mcu_read_data return failed first 16\n"); ++ res = -EIO; ++ goto error; ++ } ++ mtk_nand_stop_read(); ++ sector++; ++ len -= read_len; ++ } ++ } ++error: ++ NFI_CLN_REG16(NFI_CON_REG16, CON_NFI_BRD); ++ return res; ++} ++ ++static int ++mtk_nand_write_oob_raw(struct mtd_info *mtd, const uint8_t * buf, int page_addr, int len) ++{ ++ struct nand_chip *chip = mtd->priv; ++ u32 col_addr = 0; ++ u32 sector = 0; ++ int write_len = 0; ++ int status; ++ int sec_num = 1<<(chip->page_shift-9); ++ int spare_per_sector = mtd->oobsize/sec_num; ++ ++ if (len > NAND_MAX_OOBSIZE || len % OOB_AVAI_PER_SECTOR || !buf) { ++ printk(KERN_WARNING "[%s] invalid parameter, len: %d, buf: %p\n", __FUNCTION__, len, buf); ++ return -EINVAL; ++ } ++ ++ while (len > 0) { ++ write_len = min(len, spare_per_sector); ++ col_addr = sector * (NAND_SECTOR_SIZE + spare_per_sector) + NAND_SECTOR_SIZE; ++ if (!mtk_nand_ready_for_write(chip, page_addr, col_addr, false, NULL)) ++ return -EIO; ++ if (!mtk_nand_mcu_write_data(mtd, buf + sector * spare_per_sector, write_len)) ++ return -EIO; ++ (void)mtk_nand_check_RW_count(write_len); ++ NFI_CLN_REG16(NFI_CON_REG16, CON_NFI_BWR); ++ (void)mtk_nand_set_command(NAND_CMD_PAGEPROG); ++ while (DRV_Reg32(NFI_STA_REG32) & STA_NAND_BUSY) ++ ; ++ status = chip->waitfunc(mtd, chip); ++ if (status & NAND_STATUS_FAIL) { ++ printk(KERN_INFO "status: %d\n", status); ++ return -EIO; ++ } ++ len -= write_len; ++ sector++; ++ } ++ ++ return 0; ++} ++ ++static int ++mtk_nand_write_oob_hw(struct mtd_info *mtd, struct nand_chip *chip, int page) ++{ ++ int i, iter; ++ int sec_num = 1<<(chip->page_shift-9); ++ int spare_per_sector = mtd->oobsize/sec_num; ++ ++ memcpy(local_oob_buf, chip->oob_poi, mtd->oobsize); ++ ++ // copy ecc data ++ for (i = 0; i < layout->eccbytes; i++) { ++ iter = (i / (spare_per_sector-OOB_AVAI_PER_SECTOR)) * spare_per_sector + OOB_AVAI_PER_SECTOR + i % (spare_per_sector-OOB_AVAI_PER_SECTOR); ++ local_oob_buf[iter] = chip->oob_poi[layout->eccpos[i]]; ++ } ++ ++ // copy FDM data ++ for (i = 0; i < sec_num; i++) ++ memcpy(&local_oob_buf[i * spare_per_sector], &chip->oob_poi[i * OOB_AVAI_PER_SECTOR], OOB_AVAI_PER_SECTOR); ++ ++ return mtk_nand_write_oob_raw(mtd, local_oob_buf, page, mtd->oobsize); ++} ++ ++static int mtk_nand_write_oob(struct mtd_info *mtd, struct nand_chip *chip, int page) ++{ ++ int page_per_block = 1 << (chip->phys_erase_shift - chip->page_shift); ++ int block = page / page_per_block; ++ u16 page_in_block = page % page_per_block; ++ int mapped_block = block; ++ ++#if defined(MTK_NAND_BMT) ++ mapped_block = get_mapping_block_index(block); ++ // write bad index into oob ++ if (mapped_block != block) ++ set_bad_index_to_oob(chip->oob_poi, block); ++ else ++ set_bad_index_to_oob(chip->oob_poi, FAKE_INDEX); ++#else ++ if (shift_on_bbt) ++ { ++ mapped_block = block_remap(mtd, block); ++ if (mapped_block == -1) ++ return NAND_STATUS_FAIL; ++ if (nand_bbt_get(mtd, mapped_block << (chip->phys_erase_shift - chip->page_shift)) != 0x0) ++ return NAND_STATUS_FAIL; ++ } ++#endif ++ do { ++ if (mtk_nand_write_oob_hw(mtd, chip, page_in_block + mapped_block * page_per_block /* page */)) { ++ MSG(INIT, "write oob fail at block: 0x%x, page: 0x%x\n", mapped_block, page_in_block); ++#if defined(MTK_NAND_BMT) ++ if (update_bmt((page_in_block + mapped_block * page_per_block) << chip->page_shift, ++ UPDATE_WRITE_FAIL, NULL, chip->oob_poi)) ++ { ++ MSG(INIT, "Update BMT success\n"); ++ return 0; ++ } else { ++ MSG(INIT, "Update BMT fail\n"); ++ return -EIO; ++ } ++#else ++ mtk_nand_block_markbad_hw(mtd, (page_in_block + mapped_block * page_per_block) << chip->page_shift); ++ nand_bbt_set(mtd, page_in_block + mapped_block * page_per_block, 0x3); ++ if (shift_on_bbt) { ++ mapped_block = block_remap(mtd, mapped_block); ++ if (mapped_block == -1) ++ return NAND_STATUS_FAIL; ++ if (nand_bbt_get(mtd, mapped_block << (chip->phys_erase_shift - chip->page_shift)) != 0x0) ++ return NAND_STATUS_FAIL; ++ } else { ++ return NAND_STATUS_FAIL; ++ } ++#endif ++ } else ++ break; ++ } while (1); ++ ++ return 0; ++} ++ ++int ++mtk_nand_block_markbad_hw(struct mtd_info *mtd, loff_t offset) ++{ ++ struct nand_chip *chip = mtd->priv; ++ int block = (int)offset >> chip->phys_erase_shift; ++ int page = block * (1 << (chip->phys_erase_shift - chip->page_shift)); ++ u8 buf[8]; ++ ++ memset(buf, 0xFF, 8); ++ buf[0] = 0; ++ return mtk_nand_write_oob_raw(mtd, buf, page, 8); ++} ++ ++static int ++mtk_nand_block_markbad(struct mtd_info *mtd, loff_t offset) ++{ ++ struct nand_chip *chip = mtd->priv; ++ int block = (int)offset >> chip->phys_erase_shift; ++ int ret; ++ int mapped_block = block; ++ ++ nand_get_device(chip, mtd, FL_WRITING); ++ ++#if defined(MTK_NAND_BMT) ++ mapped_block = get_mapping_block_index(block); ++ ret = mtk_nand_block_markbad_hw(mtd, mapped_block << chip->phys_erase_shift); ++#else ++ if (shift_on_bbt) { ++ mapped_block = block_remap(mtd, block); ++ if (mapped_block == -1) { ++ printk("NAND mark bad failed\n"); ++ nand_release_device(mtd); ++ return NAND_STATUS_FAIL; ++ } ++ } ++ ret = mtk_nand_block_markbad_hw(mtd, mapped_block << chip->phys_erase_shift); ++#endif ++ nand_release_device(mtd); ++ ++ return ret; ++} ++ ++int ++mtk_nand_read_oob_hw(struct mtd_info *mtd, struct nand_chip *chip, int page) ++{ ++ int i; ++ u8 iter = 0; ++ ++ int sec_num = 1<<(chip->page_shift-9); ++ int spare_per_sector = mtd->oobsize/sec_num; ++ ++ if (mtk_nand_read_oob_raw(mtd, chip->oob_poi, page, mtd->oobsize)) { ++ printk(KERN_ERR "[%s]mtk_nand_read_oob_raw return failed\n", __FUNCTION__); ++ return -EIO; ++ } ++ ++ // adjust to ecc physical layout to memory layout ++ /*********************************************************/ ++ /* FDM0 | ECC0 | FDM1 | ECC1 | FDM2 | ECC2 | FDM3 | ECC3 */ ++ /* 8B | 8B | 8B | 8B | 8B | 8B | 8B | 8B */ ++ /*********************************************************/ ++ ++ memcpy(local_oob_buf, chip->oob_poi, mtd->oobsize); ++ // copy ecc data ++ for (i = 0; i < layout->eccbytes; i++) { ++ iter = (i / (spare_per_sector-OOB_AVAI_PER_SECTOR)) * spare_per_sector + OOB_AVAI_PER_SECTOR + i % (spare_per_sector-OOB_AVAI_PER_SECTOR); ++ chip->oob_poi[layout->eccpos[i]] = local_oob_buf[iter]; ++ } ++ ++ // copy FDM data ++ for (i = 0; i < sec_num; i++) { ++ memcpy(&chip->oob_poi[i * OOB_AVAI_PER_SECTOR], &local_oob_buf[i * spare_per_sector], OOB_AVAI_PER_SECTOR); ++ } ++ ++ return 0; ++} ++ ++static int ++mtk_nand_read_oob(struct mtd_info *mtd, struct nand_chip *chip, int page) ++{ ++ int page_per_block = 1 << (chip->phys_erase_shift - chip->page_shift); ++ int block = page / page_per_block; ++ u16 page_in_block = page % page_per_block; ++ int mapped_block = block; ++ ++#if defined (MTK_NAND_BMT) ++ mapped_block = get_mapping_block_index(block); ++ mtk_nand_read_oob_hw(mtd, chip, page_in_block + mapped_block * page_per_block); ++#else ++ if (shift_on_bbt) { ++ mapped_block = block_remap(mtd, block); ++ if (mapped_block == -1) ++ return NAND_STATUS_FAIL; ++ // allow to read oob even if the block is bad ++ } ++ if (mtk_nand_read_oob_hw(mtd, chip, page_in_block + mapped_block * page_per_block)!=0) ++ return -1; ++#endif ++ return 0; ++} ++ ++int ++mtk_nand_block_bad_hw(struct mtd_info *mtd, loff_t ofs) ++{ ++ struct nand_chip *chip = (struct nand_chip *)mtd->priv; ++ int page_addr = (int)(ofs >> chip->page_shift); ++ unsigned int page_per_block = 1 << (chip->phys_erase_shift - chip->page_shift); ++ unsigned char oob_buf[8]; ++ ++ page_addr &= ~(page_per_block - 1); ++ if (mtk_nand_read_oob_raw(mtd, oob_buf, page_addr, sizeof(oob_buf))) { ++ printk(KERN_WARNING "mtk_nand_read_oob_raw return error\n"); ++ return 1; ++ } ++ ++ if (oob_buf[0] != 0xff) { ++ printk(KERN_WARNING "Bad block detected at 0x%x, oob_buf[0] is 0x%x\n", page_addr, oob_buf[0]); ++ // dump_nfi(); ++ return 1; ++ } ++ ++ return 0; ++} ++ ++static int ++mtk_nand_block_bad(struct mtd_info *mtd, loff_t ofs) ++{ ++ struct nand_chip *chip = (struct nand_chip *)mtd->priv; ++ int block = (int)ofs >> chip->phys_erase_shift; ++ int mapped_block = block; ++ int ret; ++ ++#if defined(MTK_NAND_BMT) ++ mapped_block = get_mapping_block_index(block); ++#else ++ if (shift_on_bbt) { ++ mapped_block = block_remap(mtd, block); ++ } ++#endif ++ ++ ret = mtk_nand_block_bad_hw(mtd, mapped_block << chip->phys_erase_shift); ++#if defined (MTK_NAND_BMT) ++ if (ret) { ++ MSG(INIT, "Unmapped bad block: 0x%x\n", mapped_block); ++ if (update_bmt(mapped_block << chip->phys_erase_shift, UPDATE_UNMAPPED_BLOCK, NULL, NULL)) { ++ MSG(INIT, "Update BMT success\n"); ++ ret = 0; ++ } else { ++ MSG(INIT, "Update BMT fail\n"); ++ ret = 1; ++ } ++ } ++#endif ++ ++ return ret; ++} ++ ++#ifdef CONFIG_MTD_NAND_VERIFY_WRITE ++char gacBuf[4096 + 288]; ++ ++static int ++mtk_nand_verify_buf(struct mtd_info *mtd, const uint8_t * buf, int len) ++{ ++ struct nand_chip *chip = (struct nand_chip *)mtd->priv; ++ struct NAND_CMD *pkCMD = &g_kCMD; ++ u32 u4PageSize = mtd->writesize; ++ u32 *pSrc, *pDst; ++ int i; ++ ++ mtk_nand_exec_read_page(mtd, pkCMD->u4RowAddr, u4PageSize, gacBuf, gacBuf + u4PageSize); ++ ++ pSrc = (u32 *) buf; ++ pDst = (u32 *) gacBuf; ++ len = len / sizeof(u32); ++ for (i = 0; i < len; ++i) { ++ if (*pSrc != *pDst) { ++ MSG(VERIFY, "mtk_nand_verify_buf page fail at page %d\n", pkCMD->u4RowAddr); ++ return -1; ++ } ++ pSrc++; ++ pDst++; ++ } ++ ++ pSrc = (u32 *) chip->oob_poi; ++ pDst = (u32 *) (gacBuf + u4PageSize); ++ ++ if ((pSrc[0] != pDst[0]) || (pSrc[1] != pDst[1]) || (pSrc[2] != pDst[2]) || (pSrc[3] != pDst[3]) || (pSrc[4] != pDst[4]) || (pSrc[5] != pDst[5])) { ++ // TODO: Ask Designer Why? ++ //(pSrc[6] != pDst[6]) || (pSrc[7] != pDst[7])) ++ MSG(VERIFY, "mtk_nand_verify_buf oob fail at page %d\n", pkCMD->u4RowAddr); ++ MSG(VERIFY, "0x%x 0x%x 0x%x 0x%x 0x%x 0x%x 0x%x 0x%x\n", pSrc[0], pSrc[1], pSrc[2], pSrc[3], pSrc[4], pSrc[5], pSrc[6], pSrc[7]); ++ MSG(VERIFY, "0x%x 0x%x 0x%x 0x%x 0x%x 0x%x 0x%x 0x%x\n", pDst[0], pDst[1], pDst[2], pDst[3], pDst[4], pDst[5], pDst[6], pDst[7]); ++ return -1; ++ } ++ return 0; ++} ++#endif ++ ++static void ++mtk_nand_init_hw(struct mtk_nand_host *host) { ++ struct mtk_nand_host_hw *hw = host->hw; ++ u32 data; ++ ++ data = DRV_Reg32(RALINK_SYSCTL_BASE+0x60); ++ data &= ~((0x3<<18)|(0x3<<16)); ++ data |= ((0x2<<18) |(0x2<<16)); ++ DRV_WriteReg32(RALINK_SYSCTL_BASE+0x60, data); ++ ++ MSG(INIT, "Enable NFI Clock\n"); ++ nand_enable_clock(); ++ ++ g_bInitDone = false; ++ g_kCMD.u4OOBRowAddr = (u32) - 1; ++ ++ /* Set default NFI access timing control */ ++ DRV_WriteReg32(NFI_ACCCON_REG32, hw->nfi_access_timing); ++ DRV_WriteReg16(NFI_CNFG_REG16, 0); ++ DRV_WriteReg16(NFI_PAGEFMT_REG16, 0); ++ ++ /* Reset the state machine and data FIFO, because flushing FIFO */ ++ (void)mtk_nand_reset(); ++ ++ /* Set the ECC engine */ ++ if (hw->nand_ecc_mode == NAND_ECC_HW) { ++ MSG(INIT, "%s : Use HW ECC\n", MODULE_NAME); ++ if (g_bHwEcc) ++ NFI_SET_REG32(NFI_CNFG_REG16, CNFG_HW_ECC_EN); ++ ECC_Config(host->hw,4); ++ mtk_nand_configure_fdm(8); ++ mtk_nand_configure_lock(); ++ } ++ ++ NFI_SET_REG16(NFI_IOCON_REG16, 0x47); ++} ++ ++static int mtk_nand_dev_ready(struct mtd_info *mtd) ++{ ++ return !(DRV_Reg32(NFI_STA_REG32) & STA_NAND_BUSY); ++} ++ ++#define FACT_BBT_BLOCK_NUM 32 // use the latest 32 BLOCK for factory bbt table ++#define FACT_BBT_OOB_SIGNATURE 1 ++#define FACT_BBT_SIGNATURE_LEN 7 ++const u8 oob_signature[] = "mtknand"; ++static u8 *fact_bbt = 0; ++static u32 bbt_size = 0; ++ ++static int ++read_fact_bbt(struct mtd_info *mtd, unsigned int page) ++{ ++ struct nand_chip *chip = mtd->priv; ++ ++ // read oob ++ if (mtk_nand_read_oob_hw(mtd, chip, page)==0) ++ { ++ if (chip->oob_poi[nand_badblock_offset] != 0xFF) ++ { ++ printk("Bad Block on Page %x\n", page); ++ return -1; ++ } ++ if (memcmp(&chip->oob_poi[FACT_BBT_OOB_SIGNATURE], oob_signature, FACT_BBT_SIGNATURE_LEN) != 0) ++ { ++ printk("compare signature failed %x\n", page); ++ return -1; ++ } ++ if (mtk_nand_exec_read_page(mtd, page, mtd->writesize, chip->buffers->databuf, chip->oob_poi)) ++ { ++ printk("Signature matched and data read!\n"); ++ memcpy(fact_bbt, chip->buffers->databuf, (bbt_size <= mtd->writesize)? bbt_size:mtd->writesize); ++ return 0; ++ } ++ ++ } ++ printk("failed at page %x\n", page); ++ return -1; ++} ++ ++static int ++load_fact_bbt(struct mtd_info *mtd) ++{ ++ struct nand_chip *chip = mtd->priv; ++ int i; ++ u32 total_block; ++ ++ total_block = 1 << (chip->chip_shift - chip->phys_erase_shift); ++ bbt_size = total_block >> 2; ++ ++ if ((!fact_bbt) && (bbt_size)) ++ fact_bbt = (u8 *)kmalloc(bbt_size, GFP_KERNEL); ++ if (!fact_bbt) ++ return -1; ++ ++ for (i = total_block - 1; i >= (total_block - FACT_BBT_BLOCK_NUM); i--) ++ { ++ if (read_fact_bbt(mtd, i << (chip->phys_erase_shift - chip->page_shift)) == 0) ++ { ++ printk("load_fact_bbt success %d\n", i); ++ return 0; ++ } ++ ++ } ++ printk("load_fact_bbt failed\n"); ++ return -1; ++} ++ ++static int oob_mtk_ooblayout_ecc(struct mtd_info *mtd, int section, ++ struct mtd_oob_region *oobregion) ++{ ++ oobregion->length = 8; ++ oobregion->offset = layout->eccpos[section * 8]; ++ ++ return 0; ++} ++ ++static int oob_mtk_ooblayout_free(struct mtd_info *mtd, int section, ++ struct mtd_oob_region *oobregion) ++{ ++ if (section >= (layout->eccbytes / 8)) { ++ return -ERANGE; ++ } ++ oobregion->offset = layout->oobfree[section].offset; ++ oobregion->length = layout->oobfree[section].length; ++ ++ return 0; ++} ++ ++ ++static const struct mtd_ooblayout_ops oob_mtk_ops = { ++ .ecc = oob_mtk_ooblayout_ecc, ++ .free = oob_mtk_ooblayout_free, ++}; ++ ++static int ++mtk_nand_probe(struct platform_device *pdev) ++{ ++ struct mtd_part_parser_data ppdata; ++ struct mtk_nand_host_hw *hw; ++ struct nand_chip *nand_chip; ++ struct mtd_info *mtd; ++ u8 ext_id1, ext_id2, ext_id3; ++ int err = 0; ++ int id; ++ u32 ext_id; ++ int i; ++ u32 data; ++ ++ data = DRV_Reg32(RALINK_SYSCTL_BASE+0x60); ++ data &= ~((0x3<<18)|(0x3<<16)); ++ data |= ((0x2<<18) |(0x2<<16)); ++ DRV_WriteReg32(RALINK_SYSCTL_BASE+0x60, data); ++ ++ hw = &mt7621_nand_hw; ++ BUG_ON(!hw); ++ /* Allocate memory for the device structure (and zero it) */ ++ host = kzalloc(sizeof(struct mtk_nand_host), GFP_KERNEL); ++ if (!host) { ++ MSG(INIT, "mtk_nand: failed to allocate device structure.\n"); ++ return -ENOMEM; ++ } ++ ++ host->hw = hw; ++ ++ /* init mtd data structure */ ++ nand_chip = &host->nand_chip; ++ nand_chip->priv = host; /* link the private data structures */ ++ ++ mtd = host->mtd = &nand_chip->mtd; ++ mtd->priv = nand_chip; ++ mtd->owner = THIS_MODULE; ++ mtd->name = "MT7621-NAND"; ++ ++ hw->nand_ecc_mode = NAND_ECC_HW; ++ ++ /* Set address of NAND IO lines */ ++ nand_chip->IO_ADDR_R = (void __iomem *)NFI_DATAR_REG32; ++ nand_chip->IO_ADDR_W = (void __iomem *)NFI_DATAW_REG32; ++ nand_chip->chip_delay = 20; /* 20us command delay time */ ++ nand_chip->ecc.mode = hw->nand_ecc_mode; /* enable ECC */ ++ nand_chip->ecc.strength = 1; ++ nand_chip->read_byte = mtk_nand_read_byte; ++ nand_chip->read_buf = mtk_nand_read_buf; ++ nand_chip->write_buf = mtk_nand_write_buf; ++#ifdef CONFIG_MTD_NAND_VERIFY_WRITE ++ nand_chip->verify_buf = mtk_nand_verify_buf; ++#endif ++ nand_chip->select_chip = mtk_nand_select_chip; ++ nand_chip->dev_ready = mtk_nand_dev_ready; ++ nand_chip->cmdfunc = mtk_nand_command_bp; ++ nand_chip->ecc.read_page = mtk_nand_read_page_hwecc; ++ nand_chip->ecc.write_page = mtk_nand_write_page_hwecc; ++ ++ mtd_set_ooblayout(mtd, &oob_mtk_ops); ++ nand_chip->ecc.size = hw->nand_ecc_size; //2048 ++ nand_chip->ecc.bytes = hw->nand_ecc_bytes; //32 ++ ++ // For BMT, we need to revise driver architecture ++ nand_chip->write_page = mtk_nand_write_page; ++ nand_chip->ecc.write_oob = mtk_nand_write_oob; ++ nand_chip->block_markbad = mtk_nand_block_markbad; // need to add nand_get_device()/nand_release_device(). ++ nand_chip->read_page = mtk_nand_read_page; ++ nand_chip->ecc.read_oob = mtk_nand_read_oob; ++ nand_chip->block_bad = mtk_nand_block_bad; ++ nand_chip->cmd_ctrl = mtk_nfc_cmd_ctrl; ++ ++ //Qwert:Add for Uboot ++ mtk_nand_init_hw(host); ++ /* Select the device */ ++ nand_chip->select_chip(mtd, NFI_DEFAULT_CS); ++ ++ /* ++ * Reset the chip, required by some chips (e.g. Micron MT29FxGxxxxx) ++ * after power-up ++ */ ++ nand_chip->cmdfunc(mtd, NAND_CMD_RESET, -1, -1); ++ ++ memset(&devinfo, 0 , sizeof(flashdev_info)); ++ ++ /* Send the command for reading device ID */ ++ ++ nand_chip->cmdfunc(mtd, NAND_CMD_READID, 0x00, -1); ++ ++ /* Read manufacturer and device IDs */ ++ manu_id = nand_chip->read_byte(mtd); ++ dev_id = nand_chip->read_byte(mtd); ++ id = dev_id | (manu_id << 8); ++ ext_id1 = nand_chip->read_byte(mtd); ++ ext_id2 = nand_chip->read_byte(mtd); ++ ext_id3 = nand_chip->read_byte(mtd); ++ ext_id = ext_id1 << 16 | ext_id2 << 8 | ext_id3; ++ if (!get_device_info(id, ext_id, &devinfo)) { ++ u32 chip_mode = RALINK_REG(RALINK_SYSCTL_BASE+0x010)&0x0F; ++ MSG(INIT, "Not Support this Device! \r\n"); ++ memset(&devinfo, 0 , sizeof(flashdev_info)); ++ MSG(INIT, "chip_mode=%08X\n",chip_mode); ++ ++ /* apply bootstrap first */ ++ devinfo.addr_cycle = 5; ++ devinfo.iowidth = 8; ++ ++ switch (chip_mode) { ++ case 10: ++ devinfo.pagesize = 2048; ++ devinfo.sparesize = 128; ++ devinfo.totalsize = 128; ++ devinfo.blocksize = 128; ++ break; ++ case 11: ++ devinfo.pagesize = 4096; ++ devinfo.sparesize = 128; ++ devinfo.totalsize = 1024; ++ devinfo.blocksize = 256; ++ break; ++ case 12: ++ devinfo.pagesize = 4096; ++ devinfo.sparesize = 224; ++ devinfo.totalsize = 2048; ++ devinfo.blocksize = 512; ++ break; ++ default: ++ case 1: ++ devinfo.pagesize = 2048; ++ devinfo.sparesize = 64; ++ devinfo.totalsize = 128; ++ devinfo.blocksize = 128; ++ break; ++ } ++ ++ devinfo.timmingsetting = NFI_DEFAULT_ACCESS_TIMING; ++ devinfo.devciename[0] = 'U'; ++ devinfo.advancedmode = 0; ++ } ++ mtd->writesize = devinfo.pagesize; ++ mtd->erasesize = (devinfo.blocksize<<10); ++ mtd->oobsize = devinfo.sparesize; ++ ++ nand_chip->chipsize = (devinfo.totalsize<<20); ++ nand_chip->page_shift = ffs(mtd->writesize) - 1; ++ nand_chip->pagemask = (nand_chip->chipsize >> nand_chip->page_shift) - 1; ++ nand_chip->phys_erase_shift = ffs(mtd->erasesize) - 1; ++ nand_chip->chip_shift = ffs(nand_chip->chipsize) - 1;//0x1C;//ffs(nand_chip->chipsize) - 1; ++ nand_chip->cmd_ctrl = mtk_nfc_cmd_ctrl; ++ ++ if (devinfo.pagesize == 4096) ++ layout = &nand_oob_128; ++ else if (devinfo.pagesize == 2048) ++ layout = &nand_oob_64; ++ else if (devinfo.pagesize == 512) ++ layout = &nand_oob_16; ++ ++ layout->eccbytes = devinfo.sparesize-OOB_AVAI_PER_SECTOR*(devinfo.pagesize/NAND_SECTOR_SIZE); ++ for (i = 0; i < layout->eccbytes; i++) ++ layout->eccpos[i]=OOB_AVAI_PER_SECTOR*(devinfo.pagesize/NAND_SECTOR_SIZE)+i; ++ ++ MSG(INIT, "Support this Device in MTK table! %x \r\n", id); ++ hw->nfi_bus_width = devinfo.iowidth; ++ DRV_WriteReg32(NFI_ACCCON_REG32, devinfo.timmingsetting); ++ ++ /* 16-bit bus width */ ++ if (hw->nfi_bus_width == 16) { ++ MSG(INIT, "%s : Set the 16-bit I/O settings!\n", MODULE_NAME); ++ nand_chip->options |= NAND_BUSWIDTH_16; ++ } ++ mtd->oobsize = devinfo.sparesize; ++ hw->nfi_cs_num = 1; ++ ++ nand_chip->options |= NAND_USE_BOUNCE_BUFFER; ++ nand_chip->buf_align = 16; ++ ++ /* Scan to find existance of the device */ ++ if (nand_scan(mtd, hw->nfi_cs_num)) { ++ MSG(INIT, "%s : nand_scan fail.\n", MODULE_NAME); ++ err = -ENXIO; ++ goto out; ++ } ++ ++ nand_chip->erase = mtk_nand_erase; ++ ++ g_page_size = mtd->writesize; ++ platform_set_drvdata(pdev, host); ++ if (hw->nfi_bus_width == 16) { ++ NFI_SET_REG16(NFI_PAGEFMT_REG16, PAGEFMT_DBYTE_EN); ++ } ++ ++ nand_chip->select_chip(mtd, 0); ++#if defined(MTK_NAND_BMT) ++ nand_chip->chipsize -= (BMT_POOL_SIZE) << nand_chip->phys_erase_shift; ++#endif ++ mtd->size = nand_chip->chipsize; ++ ++ CFG_BLOCKSIZE = mtd->erasesize; ++ ++#if defined(MTK_NAND_BMT) ++ if (!g_bmt) { ++ if (!(g_bmt = init_bmt(nand_chip, BMT_POOL_SIZE))) { ++ MSG(INIT, "Error: init bmt failed\n"); ++ return 0; ++ } ++ } ++#endif ++ ++ nand_set_flash_node(nand_chip, pdev->dev.of_node); ++ err = mtd_device_parse_register(mtd, probe_types, &ppdata, ++ NULL, 0); ++ if (!err) { ++ MSG(INIT, "[mtk_nand] probe successfully!\n"); ++ nand_disable_clock(); ++ shift_on_bbt = 0; ++ if (load_fact_bbt(mtd) == 0) { ++ int i; ++ for (i = 0; i < 0x100; i++) ++ nand_chip->bbt[i] |= fact_bbt[i]; ++ } ++ ++ return err; ++ } ++ ++out: ++ MSG(INIT, "[NFI] mtk_nand_probe fail, err = %d!\n", err); ++ nand_release(mtd); ++ platform_set_drvdata(pdev, NULL); ++ kfree(host); ++ nand_disable_clock(); ++ return err; ++} ++ ++static int ++mtk_nand_remove(struct platform_device *pdev) ++{ ++ struct mtk_nand_host *host = platform_get_drvdata(pdev); ++ struct mtd_info *mtd = host->mtd; ++ struct nand_chip *nand_chip = &host->nand_chip; ++ ++ nand_release(mtd); ++ kfree(host); ++ nand_disable_clock(); ++ ++ return 0; ++} ++ ++static const struct of_device_id mt7621_nand_match[] = { ++ { .compatible = "mtk,mt7621-nand" }, ++ {}, ++}; ++MODULE_DEVICE_TABLE(of, mt7621_nand_match); ++ ++static struct platform_driver mtk_nand_driver = { ++ .probe = mtk_nand_probe, ++ .remove = mtk_nand_remove, ++ .driver = { ++ .name = "MT7621-NAND", ++ .owner = THIS_MODULE, ++ .of_match_table = mt7621_nand_match, ++ }, ++}; ++ ++static int __init ++mtk_nand_init(void) ++{ ++ printk("MediaTek Nand driver init, version %s\n", VERSION); ++ ++ return platform_driver_register(&mtk_nand_driver); ++} ++ ++static void __exit ++mtk_nand_exit(void) ++{ ++ platform_driver_unregister(&mtk_nand_driver); ++} ++ ++module_init(mtk_nand_init); ++module_exit(mtk_nand_exit); ++MODULE_LICENSE("GPL"); +--- /dev/null ++++ b/drivers/mtd/nand/mtk_nand2.h +@@ -0,0 +1,452 @@ ++#ifndef __MTK_NAND_H ++#define __MTK_NAND_H ++ ++#define RALINK_NAND_CTRL_BASE 0xBE003000 ++#define RALINK_SYSCTL_BASE 0xBE000000 ++#define RALINK_NANDECC_CTRL_BASE 0xBE003800 ++/******************************************************************************* ++ * NFI Register Definition ++ *******************************************************************************/ ++ ++#define NFI_CNFG_REG16 ((volatile P_U16)(NFI_BASE+0x0000)) ++#define NFI_PAGEFMT_REG16 ((volatile P_U16)(NFI_BASE+0x0004)) ++#define NFI_CON_REG16 ((volatile P_U16)(NFI_BASE+0x0008)) ++#define NFI_ACCCON_REG32 ((volatile P_U32)(NFI_BASE+0x000C)) ++#define NFI_INTR_EN_REG16 ((volatile P_U16)(NFI_BASE+0x0010)) ++#define NFI_INTR_REG16 ((volatile P_U16)(NFI_BASE+0x0014)) ++ ++#define NFI_CMD_REG16 ((volatile P_U16)(NFI_BASE+0x0020)) ++ ++#define NFI_ADDRNOB_REG16 ((volatile P_U16)(NFI_BASE+0x0030)) ++#define NFI_COLADDR_REG32 ((volatile P_U32)(NFI_BASE+0x0034)) ++#define NFI_ROWADDR_REG32 ((volatile P_U32)(NFI_BASE+0x0038)) ++ ++#define NFI_STRDATA_REG16 ((volatile P_U16)(NFI_BASE+0x0040)) ++ ++#define NFI_DATAW_REG32 ((volatile P_U32)(NFI_BASE+0x0050)) ++#define NFI_DATAR_REG32 ((volatile P_U32)(NFI_BASE+0x0054)) ++#define NFI_PIO_DIRDY_REG16 ((volatile P_U16)(NFI_BASE+0x0058)) ++ ++#define NFI_STA_REG32 ((volatile P_U32)(NFI_BASE+0x0060)) ++#define NFI_FIFOSTA_REG16 ((volatile P_U16)(NFI_BASE+0x0064)) ++#define NFI_LOCKSTA_REG16 ((volatile P_U16)(NFI_BASE+0x0068)) ++ ++#define NFI_ADDRCNTR_REG16 ((volatile P_U16)(NFI_BASE+0x0070)) ++ ++#define NFI_STRADDR_REG32 ((volatile P_U32)(NFI_BASE+0x0080)) ++#define NFI_BYTELEN_REG16 ((volatile P_U16)(NFI_BASE+0x0084)) ++ ++#define NFI_CSEL_REG16 ((volatile P_U16)(NFI_BASE+0x0090)) ++#define NFI_IOCON_REG16 ((volatile P_U16)(NFI_BASE+0x0094)) ++ ++#define NFI_FDM0L_REG32 ((volatile P_U32)(NFI_BASE+0x00A0)) ++#define NFI_FDM0M_REG32 ((volatile P_U32)(NFI_BASE+0x00A4)) ++ ++#define NFI_LOCK_REG16 ((volatile P_U16)(NFI_BASE+0x0100)) ++#define NFI_LOCKCON_REG32 ((volatile P_U32)(NFI_BASE+0x0104)) ++#define NFI_LOCKANOB_REG16 ((volatile P_U16)(NFI_BASE+0x0108)) ++#define NFI_LOCK00ADD_REG32 ((volatile P_U32)(NFI_BASE+0x0110)) ++#define NFI_LOCK00FMT_REG32 ((volatile P_U32)(NFI_BASE+0x0114)) ++#define NFI_LOCK01ADD_REG32 ((volatile P_U32)(NFI_BASE+0x0118)) ++#define NFI_LOCK01FMT_REG32 ((volatile P_U32)(NFI_BASE+0x011C)) ++#define NFI_LOCK02ADD_REG32 ((volatile P_U32)(NFI_BASE+0x0120)) ++#define NFI_LOCK02FMT_REG32 ((volatile P_U32)(NFI_BASE+0x0124)) ++#define NFI_LOCK03ADD_REG32 ((volatile P_U32)(NFI_BASE+0x0128)) ++#define NFI_LOCK03FMT_REG32 ((volatile P_U32)(NFI_BASE+0x012C)) ++#define NFI_LOCK04ADD_REG32 ((volatile P_U32)(NFI_BASE+0x0130)) ++#define NFI_LOCK04FMT_REG32 ((volatile P_U32)(NFI_BASE+0x0134)) ++#define NFI_LOCK05ADD_REG32 ((volatile P_U32)(NFI_BASE+0x0138)) ++#define NFI_LOCK05FMT_REG32 ((volatile P_U32)(NFI_BASE+0x013C)) ++#define NFI_LOCK06ADD_REG32 ((volatile P_U32)(NFI_BASE+0x0140)) ++#define NFI_LOCK06FMT_REG32 ((volatile P_U32)(NFI_BASE+0x0144)) ++#define NFI_LOCK07ADD_REG32 ((volatile P_U32)(NFI_BASE+0x0148)) ++#define NFI_LOCK07FMT_REG32 ((volatile P_U32)(NFI_BASE+0x014C)) ++#define NFI_LOCK08ADD_REG32 ((volatile P_U32)(NFI_BASE+0x0150)) ++#define NFI_LOCK08FMT_REG32 ((volatile P_U32)(NFI_BASE+0x0154)) ++#define NFI_LOCK09ADD_REG32 ((volatile P_U32)(NFI_BASE+0x0158)) ++#define NFI_LOCK09FMT_REG32 ((volatile P_U32)(NFI_BASE+0x015C)) ++#define NFI_LOCK10ADD_REG32 ((volatile P_U32)(NFI_BASE+0x0160)) ++#define NFI_LOCK10FMT_REG32 ((volatile P_U32)(NFI_BASE+0x0164)) ++#define NFI_LOCK11ADD_REG32 ((volatile P_U32)(NFI_BASE+0x0168)) ++#define NFI_LOCK11FMT_REG32 ((volatile P_U32)(NFI_BASE+0x016C)) ++#define NFI_LOCK12ADD_REG32 ((volatile P_U32)(NFI_BASE+0x0170)) ++#define NFI_LOCK12FMT_REG32 ((volatile P_U32)(NFI_BASE+0x0174)) ++#define NFI_LOCK13ADD_REG32 ((volatile P_U32)(NFI_BASE+0x0178)) ++#define NFI_LOCK13FMT_REG32 ((volatile P_U32)(NFI_BASE+0x017C)) ++#define NFI_LOCK14ADD_REG32 ((volatile P_U32)(NFI_BASE+0x0180)) ++#define NFI_LOCK14FMT_REG32 ((volatile P_U32)(NFI_BASE+0x0184)) ++#define NFI_LOCK15ADD_REG32 ((volatile P_U32)(NFI_BASE+0x0188)) ++#define NFI_LOCK15FMT_REG32 ((volatile P_U32)(NFI_BASE+0x018C)) ++ ++#define NFI_FIFODATA0_REG32 ((volatile P_U32)(NFI_BASE+0x0190)) ++#define NFI_FIFODATA1_REG32 ((volatile P_U32)(NFI_BASE+0x0194)) ++#define NFI_FIFODATA2_REG32 ((volatile P_U32)(NFI_BASE+0x0198)) ++#define NFI_FIFODATA3_REG32 ((volatile P_U32)(NFI_BASE+0x019C)) ++#define NFI_MASTERSTA_REG16 ((volatile P_U16)(NFI_BASE+0x0210)) ++ ++ ++/******************************************************************************* ++ * NFI Register Field Definition ++ *******************************************************************************/ ++ ++/* NFI_CNFG */ ++#define CNFG_AHB (0x0001) ++#define CNFG_READ_EN (0x0002) ++#define CNFG_DMA_BURST_EN (0x0004) ++#define CNFG_BYTE_RW (0x0040) ++#define CNFG_HW_ECC_EN (0x0100) ++#define CNFG_AUTO_FMT_EN (0x0200) ++#define CNFG_OP_IDLE (0x0000) ++#define CNFG_OP_READ (0x1000) ++#define CNFG_OP_SRD (0x2000) ++#define CNFG_OP_PRGM (0x3000) ++#define CNFG_OP_ERASE (0x4000) ++#define CNFG_OP_RESET (0x5000) ++#define CNFG_OP_CUST (0x6000) ++#define CNFG_OP_MODE_MASK (0x7000) ++#define CNFG_OP_MODE_SHIFT (12) ++ ++/* NFI_PAGEFMT */ ++#define PAGEFMT_512 (0x0000) ++#define PAGEFMT_2K (0x0001) ++#define PAGEFMT_4K (0x0002) ++ ++#define PAGEFMT_PAGE_MASK (0x0003) ++ ++#define PAGEFMT_DBYTE_EN (0x0008) ++ ++#define PAGEFMT_SPARE_16 (0x0000) ++#define PAGEFMT_SPARE_26 (0x0001) ++#define PAGEFMT_SPARE_27 (0x0002) ++#define PAGEFMT_SPARE_28 (0x0003) ++#define PAGEFMT_SPARE_MASK (0x0030) ++#define PAGEFMT_SPARE_SHIFT (4) ++ ++#define PAGEFMT_FDM_MASK (0x0F00) ++#define PAGEFMT_FDM_SHIFT (8) ++ ++#define PAGEFMT_FDM_ECC_MASK (0xF000) ++#define PAGEFMT_FDM_ECC_SHIFT (12) ++ ++/* NFI_CON */ ++#define CON_FIFO_FLUSH (0x0001) ++#define CON_NFI_RST (0x0002) ++#define CON_NFI_SRD (0x0010) ++ ++#define CON_NFI_NOB_MASK (0x0060) ++#define CON_NFI_NOB_SHIFT (5) ++ ++#define CON_NFI_BRD (0x0100) ++#define CON_NFI_BWR (0x0200) ++ ++#define CON_NFI_SEC_MASK (0xF000) ++#define CON_NFI_SEC_SHIFT (12) ++ ++/* NFI_ACCCON */ ++#define ACCCON_SETTING () ++ ++/* NFI_INTR_EN */ ++#define INTR_RD_DONE_EN (0x0001) ++#define INTR_WR_DONE_EN (0x0002) ++#define INTR_RST_DONE_EN (0x0004) ++#define INTR_ERASE_DONE_EN (0x0008) ++#define INTR_BSY_RTN_EN (0x0010) ++#define INTR_ACC_LOCK_EN (0x0020) ++#define INTR_AHB_DONE_EN (0x0040) ++#define INTR_ALL_INTR_DE (0x0000) ++#define INTR_ALL_INTR_EN (0x007F) ++ ++/* NFI_INTR */ ++#define INTR_RD_DONE (0x0001) ++#define INTR_WR_DONE (0x0002) ++#define INTR_RST_DONE (0x0004) ++#define INTR_ERASE_DONE (0x0008) ++#define INTR_BSY_RTN (0x0010) ++#define INTR_ACC_LOCK (0x0020) ++#define INTR_AHB_DONE (0x0040) ++ ++/* NFI_ADDRNOB */ ++#define ADDR_COL_NOB_MASK (0x0003) ++#define ADDR_COL_NOB_SHIFT (0) ++#define ADDR_ROW_NOB_MASK (0x0030) ++#define ADDR_ROW_NOB_SHIFT (4) ++ ++/* NFI_STA */ ++#define STA_READ_EMPTY (0x00001000) ++#define STA_ACC_LOCK (0x00000010) ++#define STA_CMD_STATE (0x00000001) ++#define STA_ADDR_STATE (0x00000002) ++#define STA_DATAR_STATE (0x00000004) ++#define STA_DATAW_STATE (0x00000008) ++ ++#define STA_NAND_FSM_MASK (0x1F000000) ++#define STA_NAND_BUSY (0x00000100) ++#define STA_NAND_BUSY_RETURN (0x00000200) ++#define STA_NFI_FSM_MASK (0x000F0000) ++#define STA_NFI_OP_MASK (0x0000000F) ++ ++/* NFI_FIFOSTA */ ++#define FIFO_RD_EMPTY (0x0040) ++#define FIFO_RD_FULL (0x0080) ++#define FIFO_WR_FULL (0x8000) ++#define FIFO_WR_EMPTY (0x4000) ++#define FIFO_RD_REMAIN(x) (0x1F&(x)) ++#define FIFO_WR_REMAIN(x) ((0x1F00&(x))>>8) ++ ++/* NFI_ADDRCNTR */ ++#define ADDRCNTR_CNTR(x) ((0xF000&(x))>>12) ++#define ADDRCNTR_OFFSET(x) (0x03FF&(x)) ++ ++/* NFI_LOCK */ ++#define NFI_LOCK_ON (0x0001) ++ ++/* NFI_LOCKANOB */ ++#define PROG_RADD_NOB_MASK (0x7000) ++#define PROG_RADD_NOB_SHIFT (12) ++#define PROG_CADD_NOB_MASK (0x0300) ++#define PROG_CADD_NOB_SHIFT (8) ++#define ERASE_RADD_NOB_MASK (0x0070) ++#define ERASE_RADD_NOB_SHIFT (4) ++#define ERASE_CADD_NOB_MASK (0x0007) ++#define ERASE_CADD_NOB_SHIFT (0) ++ ++/******************************************************************************* ++ * ECC Register Definition ++ *******************************************************************************/ ++ ++#define ECC_ENCCON_REG16 ((volatile P_U16)(NFIECC_BASE+0x0000)) ++#define ECC_ENCCNFG_REG32 ((volatile P_U32)(NFIECC_BASE+0x0004)) ++#define ECC_ENCDIADDR_REG32 ((volatile P_U32)(NFIECC_BASE+0x0008)) ++#define ECC_ENCIDLE_REG32 ((volatile P_U32)(NFIECC_BASE+0x000C)) ++#define ECC_ENCPAR0_REG32 ((volatile P_U32)(NFIECC_BASE+0x0010)) ++#define ECC_ENCPAR1_REG32 ((volatile P_U32)(NFIECC_BASE+0x0014)) ++#define ECC_ENCPAR2_REG32 ((volatile P_U32)(NFIECC_BASE+0x0018)) ++#define ECC_ENCPAR3_REG32 ((volatile P_U32)(NFIECC_BASE+0x001C)) ++#define ECC_ENCPAR4_REG32 ((volatile P_U32)(NFIECC_BASE+0x0020)) ++#define ECC_ENCSTA_REG32 ((volatile P_U32)(NFIECC_BASE+0x0024)) ++#define ECC_ENCIRQEN_REG16 ((volatile P_U16)(NFIECC_BASE+0x0028)) ++#define ECC_ENCIRQSTA_REG16 ((volatile P_U16)(NFIECC_BASE+0x002C)) ++ ++#define ECC_DECCON_REG16 ((volatile P_U16)(NFIECC_BASE+0x0100)) ++#define ECC_DECCNFG_REG32 ((volatile P_U32)(NFIECC_BASE+0x0104)) ++#define ECC_DECDIADDR_REG32 ((volatile P_U32)(NFIECC_BASE+0x0108)) ++#define ECC_DECIDLE_REG16 ((volatile P_U16)(NFIECC_BASE+0x010C)) ++#define ECC_DECFER_REG16 ((volatile P_U16)(NFIECC_BASE+0x0110)) ++#define ECC_DECENUM_REG32 ((volatile P_U32)(NFIECC_BASE+0x0114)) ++#define ECC_DECDONE_REG16 ((volatile P_U16)(NFIECC_BASE+0x0118)) ++#define ECC_DECEL0_REG32 ((volatile P_U32)(NFIECC_BASE+0x011C)) ++#define ECC_DECEL1_REG32 ((volatile P_U32)(NFIECC_BASE+0x0120)) ++#define ECC_DECEL2_REG32 ((volatile P_U32)(NFIECC_BASE+0x0124)) ++#define ECC_DECEL3_REG32 ((volatile P_U32)(NFIECC_BASE+0x0128)) ++#define ECC_DECEL4_REG32 ((volatile P_U32)(NFIECC_BASE+0x012C)) ++#define ECC_DECEL5_REG32 ((volatile P_U32)(NFIECC_BASE+0x0130)) ++#define ECC_DECIRQEN_REG16 ((volatile P_U16)(NFIECC_BASE+0x0134)) ++#define ECC_DECIRQSTA_REG16 ((volatile P_U16)(NFIECC_BASE+0x0138)) ++#define ECC_FDMADDR_REG32 ((volatile P_U32)(NFIECC_BASE+0x013C)) ++#define ECC_DECFSM_REG32 ((volatile P_U32)(NFIECC_BASE+0x0140)) ++#define ECC_SYNSTA_REG32 ((volatile P_U32)(NFIECC_BASE+0x0144)) ++#define ECC_DECNFIDI_REG32 ((volatile P_U32)(NFIECC_BASE+0x0148)) ++#define ECC_SYN0_REG32 ((volatile P_U32)(NFIECC_BASE+0x014C)) ++ ++/******************************************************************************* ++ * ECC register definition ++ *******************************************************************************/ ++/* ECC_ENCON */ ++#define ENC_EN (0x0001) ++#define ENC_DE (0x0000) ++ ++/* ECC_ENCCNFG */ ++#define ECC_CNFG_ECC4 (0x0000) ++#define ECC_CNFG_ECC6 (0x0001) ++#define ECC_CNFG_ECC8 (0x0002) ++#define ECC_CNFG_ECC10 (0x0003) ++#define ECC_CNFG_ECC12 (0x0004) ++#define ECC_CNFG_ECC_MASK (0x00000007) ++ ++#define ENC_CNFG_NFI (0x0010) ++#define ENC_CNFG_MODE_MASK (0x0010) ++ ++#define ENC_CNFG_META6 (0x10300000) ++#define ENC_CNFG_META8 (0x10400000) ++ ++#define ENC_CNFG_MSG_MASK (0x1FFF0000) ++#define ENC_CNFG_MSG_SHIFT (0x10) ++ ++/* ECC_ENCIDLE */ ++#define ENC_IDLE (0x0001) ++ ++/* ECC_ENCSTA */ ++#define STA_FSM (0x001F) ++#define STA_COUNT_PS (0xFF10) ++#define STA_COUNT_MS (0x3FFF0000) ++ ++/* ECC_ENCIRQEN */ ++#define ENC_IRQEN (0x0001) ++ ++/* ECC_ENCIRQSTA */ ++#define ENC_IRQSTA (0x0001) ++ ++/* ECC_DECCON */ ++#define DEC_EN (0x0001) ++#define DEC_DE (0x0000) ++ ++/* ECC_ENCCNFG */ ++#define DEC_CNFG_ECC4 (0x0000) ++//#define DEC_CNFG_ECC6 (0x0001) ++//#define DEC_CNFG_ECC12 (0x0002) ++#define DEC_CNFG_NFI (0x0010) ++//#define DEC_CNFG_META6 (0x10300000) ++//#define DEC_CNFG_META8 (0x10400000) ++ ++#define DEC_CNFG_FER (0x01000) ++#define DEC_CNFG_EL (0x02000) ++#define DEC_CNFG_CORRECT (0x03000) ++#define DEC_CNFG_TYPE_MASK (0x03000) ++ ++#define DEC_CNFG_EMPTY_EN (0x80000000) ++ ++#define DEC_CNFG_CODE_MASK (0x1FFF0000) ++#define DEC_CNFG_CODE_SHIFT (0x10) ++ ++/* ECC_DECIDLE */ ++#define DEC_IDLE (0x0001) ++ ++/* ECC_DECFER */ ++#define DEC_FER0 (0x0001) ++#define DEC_FER1 (0x0002) ++#define DEC_FER2 (0x0004) ++#define DEC_FER3 (0x0008) ++#define DEC_FER4 (0x0010) ++#define DEC_FER5 (0x0020) ++#define DEC_FER6 (0x0040) ++#define DEC_FER7 (0x0080) ++ ++/* ECC_DECENUM */ ++#define ERR_NUM0 (0x0000000F) ++#define ERR_NUM1 (0x000000F0) ++#define ERR_NUM2 (0x00000F00) ++#define ERR_NUM3 (0x0000F000) ++#define ERR_NUM4 (0x000F0000) ++#define ERR_NUM5 (0x00F00000) ++#define ERR_NUM6 (0x0F000000) ++#define ERR_NUM7 (0xF0000000) ++ ++/* ECC_DECDONE */ ++#define DEC_DONE0 (0x0001) ++#define DEC_DONE1 (0x0002) ++#define DEC_DONE2 (0x0004) ++#define DEC_DONE3 (0x0008) ++#define DEC_DONE4 (0x0010) ++#define DEC_DONE5 (0x0020) ++#define DEC_DONE6 (0x0040) ++#define DEC_DONE7 (0x0080) ++ ++/* ECC_DECIRQEN */ ++#define DEC_IRQEN (0x0001) ++ ++/* ECC_DECIRQSTA */ ++#define DEC_IRQSTA (0x0001) ++ ++#define CHIPVER_ECO_1 (0x8a00) ++#define CHIPVER_ECO_2 (0x8a01) ++ ++//#define NAND_PFM ++ ++/******************************************************************************* ++ * Data Structure Definition ++ *******************************************************************************/ ++struct mtk_nand_host ++{ ++ struct nand_chip nand_chip; ++ struct mtd_info *mtd; ++ struct mtk_nand_host_hw *hw; ++}; ++ ++struct NAND_CMD ++{ ++ u32 u4ColAddr; ++ u32 u4RowAddr; ++ u32 u4OOBRowAddr; ++ u8 au1OOB[288]; ++ u8* pDataBuf; ++#ifdef NAND_PFM ++ u32 pureReadOOB; ++ u32 pureReadOOBNum; ++#endif ++}; ++ ++/* ++ * ECC layout control structure. Exported to userspace for ++ * diagnosis and to allow creation of raw images ++struct nand_ecclayout { ++ uint32_t eccbytes; ++ uint32_t eccpos[64]; ++ uint32_t oobavail; ++ struct nand_oobfree oobfree[MTD_MAX_OOBFREE_ENTRIES]; ++}; ++*/ ++#define __DEBUG_NAND 1 /* Debug information on/off */ ++ ++/* Debug message event */ ++#define DBG_EVT_NONE 0x00000000 /* No event */ ++#define DBG_EVT_INIT 0x00000001 /* Initial related event */ ++#define DBG_EVT_VERIFY 0x00000002 /* Verify buffer related event */ ++#define DBG_EVT_PERFORMANCE 0x00000004 /* Performance related event */ ++#define DBG_EVT_READ 0x00000008 /* Read related event */ ++#define DBG_EVT_WRITE 0x00000010 /* Write related event */ ++#define DBG_EVT_ERASE 0x00000020 /* Erase related event */ ++#define DBG_EVT_BADBLOCK 0x00000040 /* Badblock related event */ ++#define DBG_EVT_POWERCTL 0x00000080 /* Suspend/Resume related event */ ++ ++#define DBG_EVT_ALL 0xffffffff ++ ++#define DBG_EVT_MASK (DBG_EVT_INIT) ++ ++#if __DEBUG_NAND ++#define MSG(evt, fmt, args...) \ ++do { \ ++ if ((DBG_EVT_##evt) & DBG_EVT_MASK) { \ ++ printk(fmt, ##args); \ ++ } \ ++} while(0) ++ ++#define MSG_FUNC_ENTRY(f) MSG(FUC, ": %s\n", __FUNCTION__) ++#else ++#define MSG(evt, fmt, args...) do{}while(0) ++#define MSG_FUNC_ENTRY(f) do{}while(0) ++#endif ++ ++#define RAMDOM_READ 1<<0 ++#define CACHE_READ 1<<1 ++ ++typedef struct ++{ ++ u16 id; //deviceid+menuid ++ u32 ext_id; ++ u8 addr_cycle; ++ u8 iowidth; ++ u16 totalsize; ++ u16 blocksize; ++ u16 pagesize; ++ u16 sparesize; ++ u32 timmingsetting; ++ char devciename[14]; ++ u32 advancedmode; // ++}flashdev_info,*pflashdev_info; ++ ++/* NAND driver */ ++#if 0 ++struct mtk_nand_host_hw { ++ unsigned int nfi_bus_width; /* NFI_BUS_WIDTH */ ++ unsigned int nfi_access_timing; /* NFI_ACCESS_TIMING */ ++ unsigned int nfi_cs_num; /* NFI_CS_NUM */ ++ unsigned int nand_sec_size; /* NAND_SECTOR_SIZE */ ++ unsigned int nand_sec_shift; /* NAND_SECTOR_SHIFT */ ++ unsigned int nand_ecc_size; ++ unsigned int nand_ecc_bytes; ++ unsigned int nand_ecc_mode; ++}; ++extern struct mtk_nand_host_hw mt7621_nand_hw; ++extern u32 CFG_BLOCKSIZE; ++#endif ++#endif +--- a/drivers/mtd/nand/nand_base.c ++++ b/drivers/mtd/nand/nand_base.c +@@ -48,7 +48,7 @@ + #include + #include + +-static int nand_get_device(struct mtd_info *mtd, int new_state); ++int nand_get_device(struct mtd_info *mtd, int new_state); + + static int nand_do_write_oob(struct mtd_info *mtd, loff_t to, + struct mtd_oob_ops *ops); +@@ -240,7 +240,7 @@ static int check_offs_len(struct mtd_inf + * + * Release chip lock and wake up anyone waiting on the device. + */ +-static void nand_release_device(struct mtd_info *mtd) ++void nand_release_device(struct mtd_info *mtd) + { + struct nand_chip *chip = mtd_to_nand(mtd); + +@@ -968,7 +968,7 @@ static void panic_nand_get_device(struct + * + * Get the device and lock it for exclusive access + */ +-static int ++int + nand_get_device(struct mtd_info *mtd, int new_state) + { + struct nand_chip *chip = mtd_to_nand(mtd); +--- /dev/null ++++ b/drivers/mtd/nand/nand_def.h +@@ -0,0 +1,123 @@ ++#ifndef __NAND_DEF_H__ ++#define __NAND_DEF_H__ ++ ++#define VERSION "v2.1 Fix AHB virt2phys error" ++#define MODULE_NAME "# MTK NAND #" ++#define PROCNAME "driver/nand" ++ ++#undef TESTTIME ++//#define __UBOOT_NAND__ 1 ++#define __KERNEL_NAND__ 1 ++//#define __PRELOADER_NAND__ 1 ++//#define PMT 1 ++//#define _MTK_NAND_DUMMY_DRIVER ++//#define CONFIG_BADBLOCK_CHECK 1 ++//#ifdef CONFIG_BADBLOCK_CHECK ++//#define MTK_NAND_BMT 1 ++//#endif ++#define ECC_ENABLE 1 ++#define MANUAL_CORRECT 1 ++//#define __INTERNAL_USE_AHB_MODE__ (0) ++#define SKIP_BAD_BLOCK ++#define FACT_BBT ++ ++#ifndef NAND_OTP_SUPPORT ++#define NAND_OTP_SUPPORT 0 ++#endif ++ ++/******************************************************************************* ++ * Macro definition ++ *******************************************************************************/ ++//#define NFI_SET_REG32(reg, value) (DRV_WriteReg32(reg, DRV_Reg32(reg) | (value))) ++//#define NFI_SET_REG16(reg, value) (DRV_WriteReg16(reg, DRV_Reg16(reg) | (value))) ++//#define NFI_CLN_REG32(reg, value) (DRV_WriteReg32(reg, DRV_Reg32(reg) & (~(value)))) ++//#define NFI_CLN_REG16(reg, value) (DRV_WriteReg16(reg, DRV_Reg16(reg) & (~(value)))) ++ ++#if defined (__KERNEL_NAND__) ++#define NFI_SET_REG32(reg, value) \ ++do { \ ++ g_value = (DRV_Reg32(reg) | (value));\ ++ DRV_WriteReg32(reg, g_value); \ ++} while(0) ++ ++#define NFI_SET_REG16(reg, value) \ ++do { \ ++ g_value = (DRV_Reg16(reg) | (value));\ ++ DRV_WriteReg16(reg, g_value); \ ++} while(0) ++ ++#define NFI_CLN_REG32(reg, value) \ ++do { \ ++ g_value = (DRV_Reg32(reg) & (~(value)));\ ++ DRV_WriteReg32(reg, g_value); \ ++} while(0) ++ ++#define NFI_CLN_REG16(reg, value) \ ++do { \ ++ g_value = (DRV_Reg16(reg) & (~(value)));\ ++ DRV_WriteReg16(reg, g_value); \ ++} while(0) ++#endif ++ ++#define NFI_WAIT_STATE_DONE(state) do{;}while (__raw_readl(NFI_STA_REG32) & state) ++#define NFI_WAIT_TO_READY() do{;}while (!(__raw_readl(NFI_STA_REG32) & STA_BUSY2READY)) ++ ++ ++#define NAND_SECTOR_SIZE (512) ++#define OOB_PER_SECTOR (16) ++#define OOB_AVAI_PER_SECTOR (8) ++ ++#ifndef PART_SIZE_BMTPOOL ++#define BMT_POOL_SIZE (80) ++#else ++#define BMT_POOL_SIZE (PART_SIZE_BMTPOOL) ++#endif ++ ++#define PMT_POOL_SIZE (2) ++ ++#define TIMEOUT_1 0x1fff ++#define TIMEOUT_2 0x8ff ++#define TIMEOUT_3 0xffff ++#define TIMEOUT_4 0xffff//5000 //PIO ++ ++ ++/* temporarity definiation */ ++#if !defined (__KERNEL_NAND__) ++#define KERN_INFO ++#define KERN_WARNING ++#define KERN_ERR ++#define PAGE_SIZE (4096) ++#endif ++#define AddStorageTrace //AddStorageTrace ++#define STORAGE_LOGGER_MSG_NAND 0 ++#define NFI_BASE RALINK_NAND_CTRL_BASE ++#define NFIECC_BASE RALINK_NANDECC_CTRL_BASE ++ ++#ifdef __INTERNAL_USE_AHB_MODE__ ++#define MT65xx_POLARITY_LOW 0 ++#define MT65XX_PDN_PERI_NFI 0 ++#define MT65xx_EDGE_SENSITIVE 0 ++#define MT6575_NFI_IRQ_ID (58) ++#endif ++ ++#if defined (__KERNEL_NAND__) ++#define RALINK_REG(x) (*((volatile u32 *)(x))) ++#define __virt_to_phys(x) virt_to_phys((volatile void*)x) ++#else ++#define CONFIG_MTD_NAND_VERIFY_WRITE (1) ++#define printk printf ++#define ra_dbg printf ++#define BUG() //BUG() ++#define BUG_ON(x) //BUG_ON() ++#define NUM_PARTITIONS 1 ++#endif ++ ++#define NFI_DEFAULT_ACCESS_TIMING (0x30C77fff) //(0x44333) ++ ++//uboot only support 1 cs ++#define NFI_CS_NUM (1) ++#define NFI_DEFAULT_CS (0) ++ ++#include "mt6575_typedefs.h" ++ ++#endif /* __NAND_DEF_H__ */ +--- /dev/null ++++ b/drivers/mtd/nand/nand_device_list.h +@@ -0,0 +1,60 @@ ++/* Copyright Statement: ++ * ++ * This software/firmware and related documentation ("MediaTek Software") are ++ * protected under relevant copyright laws. The information contained herein ++ * is confidential and proprietary to MediaTek Inc. and/or its licensors. ++ * Without the prior written permission of MediaTek inc. and/or its licensors, ++ * any reproduction, modification, use or disclosure of MediaTek Software, ++ * and information contained herein, in whole or in part, shall be strictly prohibited. ++ */ ++/* MediaTek Inc. (C) 2010. All rights reserved. ++ * ++ * BY OPENING THIS FILE, RECEIVER HEREBY UNEQUIVOCALLY ACKNOWLEDGES AND AGREES ++ * THAT THE SOFTWARE/FIRMWARE AND ITS DOCUMENTATIONS ("MEDIATEK SOFTWARE") ++ * RECEIVED FROM MEDIATEK AND/OR ITS REPRESENTATIVES ARE PROVIDED TO RECEIVER ON ++ * AN "AS-IS" BASIS ONLY. MEDIATEK EXPRESSLY DISCLAIMS ANY AND ALL WARRANTIES, ++ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF ++ * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT. ++ * NEITHER DOES MEDIATEK PROVIDE ANY WARRANTY WHATSOEVER WITH RESPECT TO THE ++ * SOFTWARE OF ANY THIRD PARTY WHICH MAY BE USED BY, INCORPORATED IN, OR ++ * SUPPLIED WITH THE MEDIATEK SOFTWARE, AND RECEIVER AGREES TO LOOK ONLY TO SUCH ++ * THIRD PARTY FOR ANY WARRANTY CLAIM RELATING THERETO. RECEIVER EXPRESSLY ACKNOWLEDGES ++ * THAT IT IS RECEIVER'S SOLE RESPONSIBILITY TO OBTAIN FROM ANY THIRD PARTY ALL PROPER LICENSES ++ * CONTAINED IN MEDIATEK SOFTWARE. MEDIATEK SHALL ALSO NOT BE RESPONSIBLE FOR ANY MEDIATEK ++ * SOFTWARE RELEASES MADE TO RECEIVER'S SPECIFICATION OR TO CONFORM TO A PARTICULAR ++ * STANDARD OR OPEN FORUM. RECEIVER'S SOLE AND EXCLUSIVE REMEDY AND MEDIATEK'S ENTIRE AND ++ * CUMULATIVE LIABILITY WITH RESPECT TO THE MEDIATEK SOFTWARE RELEASED HEREUNDER WILL BE, ++ * AT MEDIATEK'S OPTION, TO REVISE OR REPLACE THE MEDIATEK SOFTWARE AT ISSUE, ++ * OR REFUND ANY SOFTWARE LICENSE FEES OR SERVICE CHARGE PAID BY RECEIVER TO ++ * MEDIATEK FOR SUCH MEDIATEK SOFTWARE AT ISSUE. ++ * ++ * The following software/firmware and/or related documentation ("MediaTek Software") ++ * have been modified by MediaTek Inc. All revisions are subject to any receiver's ++ * applicable license agreements with MediaTek Inc. ++ */ ++ ++#ifndef __NAND_DEVICE_LIST_H__ ++#define __NAND_DEVICE_LIST_H__ ++ ++static const flashdev_info gen_FlashTable[]={ ++ {0x20BC, 0x105554, 5, 16, 512, 128, 2048, 64, 0x1123, "EHD013151MA_5", 0}, ++ {0xECBC, 0x005554, 5, 16, 512, 128, 2048, 64, 0x1123, "K524G2GACB_A0", 0}, ++ {0x2CBC, 0x905556, 5, 16, 512, 128, 2048, 64, 0x21044333, "MT29C4G96MAZA", 0}, ++ {0x2CDA, 0x909506, 5, 8, 256, 128, 2048, 64, 0x30C77fff, "MT29F2G08ABAE", 0}, ++ {0xADBC, 0x905554, 5, 16, 512, 128, 2048, 64, 0x10801011, "H9DA4GH4JJAMC", 0}, ++ {0x01F1, 0x801D01, 4, 8, 128, 128, 2048, 64, 0x30C77fff, "S34ML01G100TF", 0}, ++ {0x92F1, 0x8095FF, 4, 8, 128, 128, 2048, 64, 0x30C77fff, "F59L1G81A", 0}, ++ {0xC8D1, 0x809540, 4, 8, 128, 128, 2048, 64, 0x30C77fff, "F59L1G81MA", 0}, ++ {0xC8DA, 0x909544, 5, 8, 256, 128, 2048, 64, 0x30C77fff, "F59L2G81A", 0}, ++ {0xC8DC, 0x909554, 5, 8, 512, 128, 2048, 64, 0x30C77fff, "F59L4G81A", 0}, ++ {0xECD3, 0x519558, 5, 8, 1024, 128, 2048, 64, 0x44333, "K9K8G8000", 0}, ++ {0xC2F1, 0x801DC2, 4, 8, 128, 128, 2048, 64, 0x30C77fff, "MX30LF1G08AA", 0}, ++ {0xC2F1, 0x809502, 4, 8, 128, 128, 2048, 64, 0x30C77fff, "MX30LF1G18AC", 0}, ++ {0x98D3, 0x902676, 5, 8, 1024, 256, 4096, 224, 0x00C25332, "TC58NVG3S0F", 0}, ++ {0x01DA, 0x909546, 5, 8, 256, 128, 2048, 128, 0x30C77fff, "S34ML02G200TF", 0}, ++ {0x01DC, 0x909556, 5, 8, 512, 128, 2048, 128, 0x30C77fff, "S34ML04G200TF", 0}, ++ {0x0000, 0x000000, 0, 0, 0, 0, 0, 0, 0, "xxxxxxxxxx", 0}, ++}; ++ ++ ++#endif +--- /dev/null ++++ b/drivers/mtd/nand/partition.h +@@ -0,0 +1,115 @@ ++/* Copyright Statement: ++ * ++ * This software/firmware and related documentation ("MediaTek Software") are ++ * protected under relevant copyright laws. The information contained herein ++ * is confidential and proprietary to MediaTek Inc. and/or its licensors. ++ * Without the prior written permission of MediaTek inc. and/or its licensors, ++ * any reproduction, modification, use or disclosure of MediaTek Software, ++ * and information contained herein, in whole or in part, shall be strictly prohibited. ++ */ ++/* MediaTek Inc. (C) 2010. All rights reserved. ++ * ++ * BY OPENING THIS FILE, RECEIVER HEREBY UNEQUIVOCALLY ACKNOWLEDGES AND AGREES ++ * THAT THE SOFTWARE/FIRMWARE AND ITS DOCUMENTATIONS ("MEDIATEK SOFTWARE") ++ * RECEIVED FROM MEDIATEK AND/OR ITS REPRESENTATIVES ARE PROVIDED TO RECEIVER ON ++ * AN "AS-IS" BASIS ONLY. MEDIATEK EXPRESSLY DISCLAIMS ANY AND ALL WARRANTIES, ++ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF ++ * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT. ++ * NEITHER DOES MEDIATEK PROVIDE ANY WARRANTY WHATSOEVER WITH RESPECT TO THE ++ * SOFTWARE OF ANY THIRD PARTY WHICH MAY BE USED BY, INCORPORATED IN, OR ++ * SUPPLIED WITH THE MEDIATEK SOFTWARE, AND RECEIVER AGREES TO LOOK ONLY TO SUCH ++ * THIRD PARTY FOR ANY WARRANTY CLAIM RELATING THERETO. RECEIVER EXPRESSLY ACKNOWLEDGES ++ * THAT IT IS RECEIVER'S SOLE RESPONSIBILITY TO OBTAIN FROM ANY THIRD PARTY ALL PROPER LICENSES ++ * CONTAINED IN MEDIATEK SOFTWARE. MEDIATEK SHALL ALSO NOT BE RESPONSIBLE FOR ANY MEDIATEK ++ * SOFTWARE RELEASES MADE TO RECEIVER'S SPECIFICATION OR TO CONFORM TO A PARTICULAR ++ * STANDARD OR OPEN FORUM. RECEIVER'S SOLE AND EXCLUSIVE REMEDY AND MEDIATEK'S ENTIRE AND ++ * CUMULATIVE LIABILITY WITH RESPECT TO THE MEDIATEK SOFTWARE RELEASED HEREUNDER WILL BE, ++ * AT MEDIATEK'S OPTION, TO REVISE OR REPLACE THE MEDIATEK SOFTWARE AT ISSUE, ++ * OR REFUND ANY SOFTWARE LICENSE FEES OR SERVICE CHARGE PAID BY RECEIVER TO ++ * MEDIATEK FOR SUCH MEDIATEK SOFTWARE AT ISSUE. ++ * ++ * The following software/firmware and/or related documentation ("MediaTek Software") ++ * have been modified by MediaTek Inc. All revisions are subject to any receiver's ++ * applicable license agreements with MediaTek Inc. ++ */ ++ ++#include ++#include ++#include ++ ++#define RECONFIG_PARTITION_SIZE 1 ++ ++#define MTD_BOOT_PART_SIZE 0x80000 ++#define MTD_CONFIG_PART_SIZE 0x20000 ++#define MTD_FACTORY_PART_SIZE 0x20000 ++ ++extern unsigned int CFG_BLOCKSIZE; ++#define LARGE_MTD_BOOT_PART_SIZE (CFG_BLOCKSIZE<<2) ++#define LARGE_MTD_CONFIG_PART_SIZE (CFG_BLOCKSIZE<<2) ++#define LARGE_MTD_FACTORY_PART_SIZE (CFG_BLOCKSIZE<<1) ++ ++/*=======================================================================*/ ++/* NAND PARTITION Mapping */ ++/*=======================================================================*/ ++//#ifdef CONFIG_MTD_PARTITIONS ++static struct mtd_partition g_pasStatic_Partition[] = { ++ { ++ name: "ALL", ++ size: MTDPART_SIZ_FULL, ++ offset: 0, ++ }, ++ /* Put your own partition definitions here */ ++ { ++ name: "Bootloader", ++ size: MTD_BOOT_PART_SIZE, ++ offset: 0, ++ }, { ++ name: "Config", ++ size: MTD_CONFIG_PART_SIZE, ++ offset: MTDPART_OFS_APPEND ++ }, { ++ name: "Factory", ++ size: MTD_FACTORY_PART_SIZE, ++ offset: MTDPART_OFS_APPEND ++#ifdef CONFIG_RT2880_ROOTFS_IN_FLASH ++ }, { ++ name: "Kernel", ++ size: MTD_KERN_PART_SIZE, ++ offset: MTDPART_OFS_APPEND, ++ }, { ++ name: "RootFS", ++ size: MTD_ROOTFS_PART_SIZE, ++ offset: MTDPART_OFS_APPEND, ++#ifdef CONFIG_ROOTFS_IN_FLASH_NO_PADDING ++ }, { ++ name: "Kernel_RootFS", ++ size: MTD_KERN_PART_SIZE + MTD_ROOTFS_PART_SIZE, ++ offset: MTD_BOOT_PART_SIZE + MTD_CONFIG_PART_SIZE + MTD_FACTORY_PART_SIZE, ++#endif ++#else //CONFIG_RT2880_ROOTFS_IN_RAM ++ }, { ++ name: "Kernel", ++ size: 0x10000, ++ offset: MTDPART_OFS_APPEND, ++#endif ++#ifdef CONFIG_DUAL_IMAGE ++ }, { ++ name: "Kernel2", ++ size: MTD_KERN2_PART_SIZE, ++ offset: MTD_KERN2_PART_OFFSET, ++#ifdef CONFIG_RT2880_ROOTFS_IN_FLASH ++ }, { ++ name: "RootFS2", ++ size: MTD_ROOTFS2_PART_SIZE, ++ offset: MTD_ROOTFS2_PART_OFFSET, ++#endif ++#endif ++ } ++ ++}; ++ ++#define NUM_PARTITIONS ARRAY_SIZE(g_pasStatic_Partition) ++extern int part_num; // = NUM_PARTITIONS; ++//#endif ++#undef RECONFIG_PARTITION_SIZE ++ diff --git a/target/linux/ramips/patches-5.4/0040-nand-hack.patch b/target/linux/ramips/patches-5.4/0040-nand-hack.patch new file mode 100644 index 0000000000..58cdf1bce7 --- /dev/null +++ b/target/linux/ramips/patches-5.4/0040-nand-hack.patch @@ -0,0 +1,32 @@ +--- a/drivers/mtd/nand/nand_base.c ++++ b/drivers/mtd/nand/nand_base.c +@@ -1908,6 +1908,9 @@ static int nand_do_read_ops(struct mtd_i + __func__, buf); + + read_retry: ++#ifdef CONFIG_MTK_MTD_NAND ++ ret = chip->read_page(mtd, chip, bufpoi, page); ++#else + if (nand_standard_page_accessors(&chip->ecc)) + chip->cmdfunc(mtd, NAND_CMD_READ0, 0x00, page); + +@@ -1927,6 +1930,7 @@ read_retry: + else + ret = chip->ecc.read_page(mtd, chip, bufpoi, + oob_required, page); ++#endif + if (ret < 0) { + if (use_bufpoi) + /* Invalidate page cache */ +--- a/include/linux/mtd/rawnand.h ++++ b/include/linux/mtd/rawnand.h +@@ -897,6 +897,9 @@ struct nand_chip { + int (*setup_data_interface)(struct mtd_info *mtd, int chipnr, + const struct nand_data_interface *conf); + ++#ifdef CONFIG_MTK_MTD_NAND ++ int (*read_page)(struct mtd_info *mtd, struct nand_chip *chip, u8 *buf, int page); ++#endif /* CONFIG_MTK_MTD_NAND */ + + int chip_delay; + unsigned int options; diff --git a/target/linux/ramips/patches-5.4/0041-DT-Add-documentation-for-spi-rt2880.patch b/target/linux/ramips/patches-5.4/0041-DT-Add-documentation-for-spi-rt2880.patch new file mode 100644 index 0000000000..e2643e3f25 --- /dev/null +++ b/target/linux/ramips/patches-5.4/0041-DT-Add-documentation-for-spi-rt2880.patch @@ -0,0 +1,44 @@ +From da6015e7f19d749f135f7ac55c4ec47b06faa868 Mon Sep 17 00:00:00 2001 +From: John Crispin +Date: Fri, 9 Aug 2013 20:12:59 +0200 +Subject: [PATCH 41/53] DT: Add documentation for spi-rt2880 + +Describe the SPI master found on the MIPS based Ralink RT2880 SoC. + +Signed-off-by: John Crispin +--- + .../devicetree/bindings/spi/spi-rt2880.txt | 28 ++++++++++++++++++++ + 1 file changed, 28 insertions(+) + create mode 100644 Documentation/devicetree/bindings/spi/spi-rt2880.txt + +--- /dev/null ++++ b/Documentation/devicetree/bindings/spi/spi-rt2880.txt +@@ -0,0 +1,28 @@ ++Ralink SoC RT2880 SPI master controller. ++ ++This SPI controller is found on most wireless SoCs made by ralink. ++ ++Required properties: ++- compatible : "ralink,rt2880-spi" ++- reg : The register base for the controller. ++- #address-cells : <1>, as required by generic SPI binding. ++- #size-cells : <0>, also as required by generic SPI binding. ++ ++Child nodes as per the generic SPI binding. ++ ++Example: ++ ++ spi@b00 { ++ compatible = "ralink,rt2880-spi"; ++ reg = <0xb00 0x100>; ++ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ m25p80@0 { ++ compatible = "m25p80"; ++ reg = <0>; ++ spi-max-frequency = <10000000>; ++ }; ++ }; ++ diff --git a/target/linux/ramips/patches-5.4/0042-SPI-ralink-add-Ralink-SoC-spi-driver.patch b/target/linux/ramips/patches-5.4/0042-SPI-ralink-add-Ralink-SoC-spi-driver.patch new file mode 100644 index 0000000000..1dd9f40c39 --- /dev/null +++ b/target/linux/ramips/patches-5.4/0042-SPI-ralink-add-Ralink-SoC-spi-driver.patch @@ -0,0 +1,574 @@ +From 683af4ebb91a1600df1946ac4769d916b8a1be65 Mon Sep 17 00:00:00 2001 +From: John Crispin +Date: Sun, 27 Jul 2014 11:15:12 +0100 +Subject: [PATCH 42/53] SPI: ralink: add Ralink SoC spi driver + +Add the driver needed to make SPI work on Ralink SoC. + +Signed-off-by: Gabor Juhos +Acked-by: John Crispin +--- + drivers/spi/Kconfig | 6 + + drivers/spi/Makefile | 1 + + drivers/spi/spi-rt2880.c | 530 ++++++++++++++++++++++++++++++++++++++++++++++ + 3 files changed, 537 insertions(+) + create mode 100644 drivers/spi/spi-rt2880.c + +--- a/drivers/spi/Kconfig ++++ b/drivers/spi/Kconfig +@@ -563,6 +563,12 @@ config SPI_QUP + This driver can also be built as a module. If so, the module + will be called spi_qup. + ++config SPI_RT2880 ++ tristate "Ralink RT288x SPI Controller" ++ depends on RALINK ++ help ++ This selects a driver for the Ralink RT288x/RT305x SPI Controller. ++ + config SPI_S3C24XX + tristate "Samsung S3C24XX series SPI" + depends on ARCH_S3C24XX +--- a/drivers/spi/Makefile ++++ b/drivers/spi/Makefile +@@ -81,6 +81,7 @@ obj-$(CONFIG_SPI_QUP) += spi-qup.o + obj-$(CONFIG_SPI_ROCKCHIP) += spi-rockchip.o + obj-$(CONFIG_SPI_RB4XX) += spi-rb4xx.o + obj-$(CONFIG_SPI_RSPI) += spi-rspi.o ++obj-$(CONFIG_SPI_RT2880) += spi-rt2880.o + obj-$(CONFIG_SPI_S3C24XX) += spi-s3c24xx-hw.o + spi-s3c24xx-hw-y := spi-s3c24xx.o + spi-s3c24xx-hw-$(CONFIG_SPI_S3C24XX_FIQ) += spi-s3c24xx-fiq.o +--- /dev/null ++++ b/drivers/spi/spi-rt2880.c +@@ -0,0 +1,530 @@ ++/* ++ * spi-rt2880.c -- Ralink RT288x/RT305x SPI controller driver ++ * ++ * Copyright (C) 2011 Sergiy ++ * Copyright (C) 2011-2013 Gabor Juhos ++ * ++ * Some parts are based on spi-orion.c: ++ * Author: Shadi Ammouri ++ * Copyright (C) 2007-2008 Marvell Ltd. ++ * ++ * This program is free software; you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License version 2 as ++ * published by the Free Software Foundation. ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#define DRIVER_NAME "spi-rt2880" ++ ++#define RAMIPS_SPI_STAT 0x00 ++#define RAMIPS_SPI_CFG 0x10 ++#define RAMIPS_SPI_CTL 0x14 ++#define RAMIPS_SPI_DATA 0x20 ++#define RAMIPS_SPI_ADDR 0x24 ++#define RAMIPS_SPI_BS 0x28 ++#define RAMIPS_SPI_USER 0x2C ++#define RAMIPS_SPI_TXFIFO 0x30 ++#define RAMIPS_SPI_RXFIFO 0x34 ++#define RAMIPS_SPI_FIFO_STAT 0x38 ++#define RAMIPS_SPI_MODE 0x3C ++#define RAMIPS_SPI_DEV_OFFSET 0x40 ++#define RAMIPS_SPI_DMA 0x80 ++#define RAMIPS_SPI_DMASTAT 0x84 ++#define RAMIPS_SPI_ARBITER 0xF0 ++ ++/* SPISTAT register bit field */ ++#define SPISTAT_BUSY BIT(0) ++ ++/* SPICFG register bit field */ ++#define SPICFG_ADDRMODE BIT(12) ++#define SPICFG_RXENVDIS BIT(11) ++#define SPICFG_RXCAP BIT(10) ++#define SPICFG_SPIENMODE BIT(9) ++#define SPICFG_MSBFIRST BIT(8) ++#define SPICFG_SPICLKPOL BIT(6) ++#define SPICFG_RXCLKEDGE_FALLING BIT(5) ++#define SPICFG_TXCLKEDGE_FALLING BIT(4) ++#define SPICFG_HIZSPI BIT(3) ++#define SPICFG_SPICLK_PRESCALE_MASK 0x7 ++#define SPICFG_SPICLK_DIV2 0 ++#define SPICFG_SPICLK_DIV4 1 ++#define SPICFG_SPICLK_DIV8 2 ++#define SPICFG_SPICLK_DIV16 3 ++#define SPICFG_SPICLK_DIV32 4 ++#define SPICFG_SPICLK_DIV64 5 ++#define SPICFG_SPICLK_DIV128 6 ++#define SPICFG_SPICLK_DISABLE 7 ++ ++/* SPICTL register bit field */ ++#define SPICTL_START BIT(4) ++#define SPICTL_HIZSDO BIT(3) ++#define SPICTL_STARTWR BIT(2) ++#define SPICTL_STARTRD BIT(1) ++#define SPICTL_SPIENA BIT(0) ++ ++/* SPIUSER register bit field */ ++#define SPIUSER_USERMODE BIT(21) ++#define SPIUSER_INSTR_PHASE BIT(20) ++#define SPIUSER_ADDR_PHASE_MASK 0x7 ++#define SPIUSER_ADDR_PHASE_OFFSET 17 ++#define SPIUSER_MODE_PHASE BIT(16) ++#define SPIUSER_DUMMY_PHASE_MASK 0x3 ++#define SPIUSER_DUMMY_PHASE_OFFSET 14 ++#define SPIUSER_DATA_PHASE_MASK 0x3 ++#define SPIUSER_DATA_PHASE_OFFSET 12 ++#define SPIUSER_DATA_READ (BIT(0) << SPIUSER_DATA_PHASE_OFFSET) ++#define SPIUSER_DATA_WRITE (BIT(1) << SPIUSER_DATA_PHASE_OFFSET) ++#define SPIUSER_ADDR_TYPE_OFFSET 9 ++#define SPIUSER_MODE_TYPE_OFFSET 6 ++#define SPIUSER_DUMMY_TYPE_OFFSET 3 ++#define SPIUSER_DATA_TYPE_OFFSET 0 ++#define SPIUSER_TRANSFER_MASK 0x7 ++#define SPIUSER_TRANSFER_SINGLE BIT(0) ++#define SPIUSER_TRANSFER_DUAL BIT(1) ++#define SPIUSER_TRANSFER_QUAD BIT(2) ++ ++#define SPIUSER_TRANSFER_TYPE(type) ( \ ++ (type << SPIUSER_ADDR_TYPE_OFFSET) | \ ++ (type << SPIUSER_MODE_TYPE_OFFSET) | \ ++ (type << SPIUSER_DUMMY_TYPE_OFFSET) | \ ++ (type << SPIUSER_DATA_TYPE_OFFSET) \ ++) ++ ++/* SPIFIFOSTAT register bit field */ ++#define SPIFIFOSTAT_TXEMPTY BIT(19) ++#define SPIFIFOSTAT_RXEMPTY BIT(18) ++#define SPIFIFOSTAT_TXFULL BIT(17) ++#define SPIFIFOSTAT_RXFULL BIT(16) ++#define SPIFIFOSTAT_FIFO_MASK 0xff ++#define SPIFIFOSTAT_TX_OFFSET 8 ++#define SPIFIFOSTAT_RX_OFFSET 0 ++ ++#define SPI_FIFO_DEPTH 16 ++ ++/* SPIMODE register bit field */ ++#define SPIMODE_MODE_OFFSET 24 ++#define SPIMODE_DUMMY_OFFSET 0 ++ ++/* SPIARB register bit field */ ++#define SPICTL_ARB_EN BIT(31) ++#define SPICTL_CSCTL1 BIT(16) ++#define SPI1_POR BIT(1) ++#define SPI0_POR BIT(0) ++ ++#define RT2880_SPI_MODE_BITS (SPI_CPOL | SPI_CPHA | SPI_LSB_FIRST | \ ++ SPI_CS_HIGH) ++ ++static atomic_t hw_reset_count = ATOMIC_INIT(0); ++ ++struct rt2880_spi { ++ struct spi_master *master; ++ void __iomem *base; ++ u32 speed; ++ u16 wait_loops; ++ u16 mode; ++ struct clk *clk; ++}; ++ ++static inline struct rt2880_spi *spidev_to_rt2880_spi(struct spi_device *spi) ++{ ++ return spi_master_get_devdata(spi->master); ++} ++ ++static inline u32 rt2880_spi_read(struct rt2880_spi *rs, u32 reg) ++{ ++ return ioread32(rs->base + reg); ++} ++ ++static inline void rt2880_spi_write(struct rt2880_spi *rs, u32 reg, ++ const u32 val) ++{ ++ iowrite32(val, rs->base + reg); ++} ++ ++static inline void rt2880_spi_setbits(struct rt2880_spi *rs, u32 reg, u32 mask) ++{ ++ void __iomem *addr = rs->base + reg; ++ ++ iowrite32((ioread32(addr) | mask), addr); ++} ++ ++static inline void rt2880_spi_clrbits(struct rt2880_spi *rs, u32 reg, u32 mask) ++{ ++ void __iomem *addr = rs->base + reg; ++ ++ iowrite32((ioread32(addr) & ~mask), addr); ++} ++ ++static u32 rt2880_spi_baudrate_get(struct spi_device *spi, unsigned int speed) ++{ ++ struct rt2880_spi *rs = spidev_to_rt2880_spi(spi); ++ u32 rate; ++ u32 prescale; ++ ++ /* ++ * the supported rates are: 2, 4, 8, ... 128 ++ * round up as we look for equal or less speed ++ */ ++ rate = DIV_ROUND_UP(clk_get_rate(rs->clk), speed); ++ rate = roundup_pow_of_two(rate); ++ ++ /* Convert the rate to SPI clock divisor value. */ ++ prescale = ilog2(rate / 2); ++ ++ /* some tolerance. double and add 100 */ ++ rs->wait_loops = (8 * HZ * loops_per_jiffy) / ++ (clk_get_rate(rs->clk) / rate); ++ rs->wait_loops = (rs->wait_loops << 1) + 100; ++ rs->speed = speed; ++ ++ dev_dbg(&spi->dev, "speed: %lu/%u, rate: %u, prescal: %u, loops: %hu\n", ++ clk_get_rate(rs->clk) / rate, speed, rate, prescale, ++ rs->wait_loops); ++ ++ return prescale; ++} ++ ++static u32 get_arbiter_offset(struct spi_master *master) ++{ ++ u32 offset; ++ ++ offset = RAMIPS_SPI_ARBITER; ++ if (master->bus_num == 1) ++ offset -= RAMIPS_SPI_DEV_OFFSET; ++ ++ return offset; ++} ++ ++static void rt2880_spi_set_cs(struct spi_device *spi, bool enable) ++{ ++ struct rt2880_spi *rs = spidev_to_rt2880_spi(spi); ++ ++ if (enable) ++ rt2880_spi_setbits(rs, RAMIPS_SPI_CTL, SPICTL_SPIENA); ++ else ++ rt2880_spi_clrbits(rs, RAMIPS_SPI_CTL, SPICTL_SPIENA); ++} ++ ++static int rt2880_spi_wait_ready(struct rt2880_spi *rs, int len) ++{ ++ int loop = rs->wait_loops * len; ++ ++ while ((rt2880_spi_read(rs, RAMIPS_SPI_STAT) & SPISTAT_BUSY) && --loop) ++ cpu_relax(); ++ ++ if (loop) ++ return 0; ++ ++ return -ETIMEDOUT; ++} ++ ++static void rt2880_dump_reg(struct spi_master *master) ++{ ++ struct rt2880_spi *rs = spi_master_get_devdata(master); ++ ++ dev_dbg(&master->dev, "stat: %08x, cfg: %08x, ctl: %08x, " \ ++ "data: %08x, arb: %08x\n", ++ rt2880_spi_read(rs, RAMIPS_SPI_STAT), ++ rt2880_spi_read(rs, RAMIPS_SPI_CFG), ++ rt2880_spi_read(rs, RAMIPS_SPI_CTL), ++ rt2880_spi_read(rs, RAMIPS_SPI_DATA), ++ rt2880_spi_read(rs, get_arbiter_offset(master))); ++} ++ ++static int rt2880_spi_transfer_one(struct spi_master *master, ++ struct spi_device *spi, struct spi_transfer *xfer) ++{ ++ struct rt2880_spi *rs = spi_master_get_devdata(master); ++ unsigned len; ++ const u8 *tx = xfer->tx_buf; ++ u8 *rx = xfer->rx_buf; ++ int err = 0; ++ ++ /* change clock speed */ ++ if (unlikely(rs->speed != xfer->speed_hz)) { ++ u32 reg; ++ reg = rt2880_spi_read(rs, RAMIPS_SPI_CFG); ++ reg &= ~SPICFG_SPICLK_PRESCALE_MASK; ++ reg |= rt2880_spi_baudrate_get(spi, xfer->speed_hz); ++ rt2880_spi_write(rs, RAMIPS_SPI_CFG, reg); ++ } ++ ++ if (tx) { ++ len = xfer->len; ++ while (len-- > 0) { ++ rt2880_spi_write(rs, RAMIPS_SPI_DATA, *tx++); ++ rt2880_spi_setbits(rs, RAMIPS_SPI_CTL, SPICTL_STARTWR); ++ err = rt2880_spi_wait_ready(rs, 1); ++ if (err) { ++ dev_err(&spi->dev, "TX failed, err=%d\n", err); ++ goto out; ++ } ++ } ++ } ++ ++ if (rx) { ++ len = xfer->len; ++ while (len-- > 0) { ++ rt2880_spi_setbits(rs, RAMIPS_SPI_CTL, SPICTL_STARTRD); ++ err = rt2880_spi_wait_ready(rs, 1); ++ if (err) { ++ dev_err(&spi->dev, "RX failed, err=%d\n", err); ++ goto out; ++ } ++ *rx++ = (u8) rt2880_spi_read(rs, RAMIPS_SPI_DATA); ++ } ++ } ++ ++out: ++ return err; ++} ++ ++/* copy from spi.c */ ++static void spi_set_cs(struct spi_device *spi, bool enable) ++{ ++ if (spi->mode & SPI_CS_HIGH) ++ enable = !enable; ++ ++ if (spi->cs_gpio >= 0) ++ gpio_set_value(spi->cs_gpio, !enable); ++ else if (spi->master->set_cs) ++ spi->master->set_cs(spi, !enable); ++} ++ ++static int rt2880_spi_setup(struct spi_device *spi) ++{ ++ struct spi_master *master = spi->master; ++ struct rt2880_spi *rs = spi_master_get_devdata(master); ++ u32 reg, old_reg, arbit_off; ++ ++ if ((spi->max_speed_hz > master->max_speed_hz) || ++ (spi->max_speed_hz < master->min_speed_hz)) { ++ dev_err(&spi->dev, "invalide requested speed %d Hz\n", ++ spi->max_speed_hz); ++ return -EINVAL; ++ } ++ ++ if (!(master->bits_per_word_mask & ++ BIT(spi->bits_per_word - 1))) { ++ dev_err(&spi->dev, "invalide bits_per_word %d\n", ++ spi->bits_per_word); ++ return -EINVAL; ++ } ++ ++ /* the hardware seems can't work on mode0 force it to mode3 */ ++ if ((spi->mode & (SPI_CPOL | SPI_CPHA)) == SPI_MODE_0) { ++ dev_warn(&spi->dev, "force spi mode3\n"); ++ spi->mode |= SPI_MODE_3; ++ } ++ ++ /* chip polarity */ ++ arbit_off = get_arbiter_offset(master); ++ reg = old_reg = rt2880_spi_read(rs, arbit_off); ++ if (spi->mode & SPI_CS_HIGH) { ++ switch (master->bus_num) { ++ case 1: ++ reg |= SPI1_POR; ++ break; ++ default: ++ reg |= SPI0_POR; ++ break; ++ } ++ } else { ++ switch (master->bus_num) { ++ case 1: ++ reg &= ~SPI1_POR; ++ break; ++ default: ++ reg &= ~SPI0_POR; ++ break; ++ } ++ } ++ ++ /* enable spi1 */ ++ if (master->bus_num == 1) ++ reg |= SPICTL_ARB_EN; ++ ++ if (reg != old_reg) ++ rt2880_spi_write(rs, arbit_off, reg); ++ ++ /* deselected the spi device */ ++ spi_set_cs(spi, false); ++ ++ rt2880_dump_reg(master); ++ ++ return 0; ++} ++ ++static int rt2880_spi_prepare_message(struct spi_master *master, ++ struct spi_message *msg) ++{ ++ struct rt2880_spi *rs = spi_master_get_devdata(master); ++ struct spi_device *spi = msg->spi; ++ u32 reg; ++ ++ if ((rs->mode == spi->mode) && (rs->speed == spi->max_speed_hz)) ++ return 0; ++ ++#if 0 ++ /* set spido to tri-state */ ++ rt2880_spi_setbits(rs, RAMIPS_SPI_CTL, SPICTL_HIZSDO); ++#endif ++ ++ reg = rt2880_spi_read(rs, RAMIPS_SPI_CFG); ++ ++ reg &= ~(SPICFG_MSBFIRST | SPICFG_SPICLKPOL | ++ SPICFG_RXCLKEDGE_FALLING | ++ SPICFG_TXCLKEDGE_FALLING | ++ SPICFG_SPICLK_PRESCALE_MASK); ++ ++ /* MSB */ ++ if (!(spi->mode & SPI_LSB_FIRST)) ++ reg |= SPICFG_MSBFIRST; ++ ++ /* spi mode */ ++ switch (spi->mode & (SPI_CPOL | SPI_CPHA)) { ++ case SPI_MODE_0: ++ reg |= SPICFG_TXCLKEDGE_FALLING; ++ break; ++ case SPI_MODE_1: ++ reg |= SPICFG_RXCLKEDGE_FALLING; ++ break; ++ case SPI_MODE_2: ++ reg |= SPICFG_SPICLKPOL | SPICFG_RXCLKEDGE_FALLING; ++ break; ++ case SPI_MODE_3: ++ reg |= SPICFG_SPICLKPOL | SPICFG_TXCLKEDGE_FALLING; ++ break; ++ } ++ rs->mode = spi->mode; ++ ++#if 0 ++ /* set spiclk and spiena to tri-state */ ++ reg |= SPICFG_HIZSPI; ++#endif ++ ++ /* clock divide */ ++ reg |= rt2880_spi_baudrate_get(spi, spi->max_speed_hz); ++ ++ rt2880_spi_write(rs, RAMIPS_SPI_CFG, reg); ++ ++ return 0; ++} ++ ++static int rt2880_spi_probe(struct platform_device *pdev) ++{ ++ struct spi_master *master; ++ struct rt2880_spi *rs; ++ void __iomem *base; ++ struct resource *r; ++ struct clk *clk; ++ int ret; ++ ++ r = platform_get_resource(pdev, IORESOURCE_MEM, 0); ++ base = devm_ioremap_resource(&pdev->dev, r); ++ if (IS_ERR(base)) ++ return PTR_ERR(base); ++ ++ clk = devm_clk_get(&pdev->dev, NULL); ++ if (IS_ERR(clk)) { ++ dev_err(&pdev->dev, "unable to get SYS clock\n"); ++ return PTR_ERR(clk); ++ } ++ ++ ret = clk_prepare_enable(clk); ++ if (ret) ++ goto err_clk; ++ ++ master = spi_alloc_master(&pdev->dev, sizeof(*rs)); ++ if (master == NULL) { ++ dev_dbg(&pdev->dev, "master allocation failed\n"); ++ ret = -ENOMEM; ++ goto err_clk; ++ } ++ ++ master->dev.of_node = pdev->dev.of_node; ++ master->mode_bits = RT2880_SPI_MODE_BITS; ++ master->bits_per_word_mask = SPI_BPW_MASK(8); ++ master->min_speed_hz = clk_get_rate(clk) / 128; ++ master->max_speed_hz = clk_get_rate(clk) / 2; ++ master->flags = SPI_MASTER_HALF_DUPLEX; ++ master->setup = rt2880_spi_setup; ++ master->prepare_message = rt2880_spi_prepare_message; ++ master->set_cs = rt2880_spi_set_cs; ++ master->transfer_one = rt2880_spi_transfer_one, ++ ++ dev_set_drvdata(&pdev->dev, master); ++ ++ rs = spi_master_get_devdata(master); ++ rs->master = master; ++ rs->base = base; ++ rs->clk = clk; ++ ++ if (atomic_inc_return(&hw_reset_count) == 1) ++ device_reset(&pdev->dev); ++ ++ ret = devm_spi_register_master(&pdev->dev, master); ++ if (ret < 0) { ++ dev_err(&pdev->dev, "devm_spi_register_master error.\n"); ++ goto err_master; ++ } ++ ++ return ret; ++ ++err_master: ++ spi_master_put(master); ++ kfree(master); ++err_clk: ++ clk_disable_unprepare(clk); ++ ++ return ret; ++} ++ ++static int rt2880_spi_remove(struct platform_device *pdev) ++{ ++ struct spi_master *master; ++ struct rt2880_spi *rs; ++ ++ master = dev_get_drvdata(&pdev->dev); ++ rs = spi_master_get_devdata(master); ++ ++ clk_disable_unprepare(rs->clk); ++ atomic_dec(&hw_reset_count); ++ ++ return 0; ++} ++ ++MODULE_ALIAS("platform:" DRIVER_NAME); ++ ++static const struct of_device_id rt2880_spi_match[] = { ++ { .compatible = "ralink,rt2880-spi" }, ++ {}, ++}; ++MODULE_DEVICE_TABLE(of, rt2880_spi_match); ++ ++static struct platform_driver rt2880_spi_driver = { ++ .driver = { ++ .name = DRIVER_NAME, ++ .owner = THIS_MODULE, ++ .of_match_table = rt2880_spi_match, ++ }, ++ .probe = rt2880_spi_probe, ++ .remove = rt2880_spi_remove, ++}; ++ ++module_platform_driver(rt2880_spi_driver); ++ ++MODULE_DESCRIPTION("Ralink SPI driver"); ++MODULE_AUTHOR("Sergiy "); ++MODULE_AUTHOR("Gabor Juhos "); ++MODULE_LICENSE("GPL"); diff --git a/target/linux/ramips/patches-5.4/0043-spi-add-mt7621-support.patch b/target/linux/ramips/patches-5.4/0043-spi-add-mt7621-support.patch new file mode 100644 index 0000000000..b607f2bdf4 --- /dev/null +++ b/target/linux/ramips/patches-5.4/0043-spi-add-mt7621-support.patch @@ -0,0 +1,487 @@ +From cbd66c626e16743b05af807ad48012c0a097b9fb Mon Sep 17 00:00:00 2001 +From: Stefan Roese +Date: Mon, 25 Mar 2019 09:29:25 +0100 +Subject: [PATCH] spi: mt7621: Move SPI driver out of staging + +This patch moves the MT7621 SPI driver, which is used on some Ralink / +MediaTek MT76xx MIPS SoC's, out of the staging directory. No changes to +the source code are done in this patch. + +This driver version was tested successfully on an MT7688 based platform +with an SPI NOR on CS0 and an SPI NAND on CS1 without any issues (so +far). + +This patch also documents the devicetree bindings for the MT7621 SPI +device driver. + +Signed-off-by: Stefan Roese +Cc: Rob Herring +Cc: Mark Brown +Cc: Greg Kroah-Hartman +Cc: NeilBrown +Cc: Sankalp Negi +Cc: Chuanhong Guo +Cc: John Crispin +Cc: Armando Miraglia +Signed-off-by: Mark Brown +--- + .../devicetree/bindings/spi/spi-mt7621.txt | 26 ++++++ + drivers/spi/Kconfig | 6 ++ + drivers/spi/Makefile | 1 + + .../{staging/mt7621-spi => spi}/spi-mt7621.c | 83 +++++++++---------- + drivers/staging/Kconfig | 2 - + drivers/staging/Makefile | 1 - + drivers/staging/mt7621-spi/Kconfig | 6 -- + drivers/staging/mt7621-spi/Makefile | 1 - + drivers/staging/mt7621-spi/TODO | 5 -- + 9 files changed, 74 insertions(+), 57 deletions(-) + create mode 100644 Documentation/devicetree/bindings/spi/spi-mt7621.txt + rename drivers/{staging/mt7621-spi => spi}/spi-mt7621.c (88%) + delete mode 100644 drivers/staging/mt7621-spi/Kconfig + delete mode 100644 drivers/staging/mt7621-spi/Makefile + delete mode 100644 drivers/staging/mt7621-spi/TODO + +--- a/drivers/spi/Kconfig ++++ b/drivers/spi/Kconfig +@@ -569,6 +569,12 @@ config SPI_RT2880 + help + This selects a driver for the Ralink RT288x/RT305x SPI Controller. + ++config SPI_MT7621 ++ tristate "MediaTek MT7621 SPI Controller" ++ depends on RALINK ++ help ++ This selects a driver for the MediaTek MT7621 SPI Controller. ++ + config SPI_S3C24XX + tristate "Samsung S3C24XX series SPI" + depends on ARCH_S3C24XX +--- a/drivers/spi/Makefile ++++ b/drivers/spi/Makefile +@@ -60,6 +60,7 @@ obj-$(CONFIG_SPI_MPC512x_PSC) += spi-mp + obj-$(CONFIG_SPI_MPC52xx_PSC) += spi-mpc52xx-psc.o + obj-$(CONFIG_SPI_MPC52xx) += spi-mpc52xx.o + obj-$(CONFIG_SPI_MT65XX) += spi-mt65xx.o ++obj-$(CONFIG_SPI_MT7621) += spi-mt7621.o + obj-$(CONFIG_SPI_MXS) += spi-mxs.o + obj-$(CONFIG_SPI_NUC900) += spi-nuc900.o + obj-$(CONFIG_SPI_OC_TINY) += spi-oc-tiny.o +--- /dev/null ++++ b/drivers/spi/spi-mt7621.c +@@ -0,0 +1,416 @@ ++// SPDX-License-Identifier: GPL-2.0 ++// ++// spi-mt7621.c -- MediaTek MT7621 SPI controller driver ++// ++// Copyright (C) 2011 Sergiy ++// Copyright (C) 2011-2013 Gabor Juhos ++// Copyright (C) 2014-2015 Felix Fietkau ++// ++// Some parts are based on spi-orion.c: ++// Author: Shadi Ammouri ++// Copyright (C) 2007-2008 Marvell Ltd. ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#define DRIVER_NAME "spi-mt7621" ++ ++/* in usec */ ++#define RALINK_SPI_WAIT_MAX_LOOP 2000 ++ ++/* SPISTAT register bit field */ ++#define SPISTAT_BUSY BIT(0) ++ ++#define MT7621_SPI_TRANS 0x00 ++#define SPITRANS_BUSY BIT(16) ++ ++#define MT7621_SPI_OPCODE 0x04 ++#define MT7621_SPI_DATA0 0x08 ++#define MT7621_SPI_DATA4 0x18 ++#define SPI_CTL_TX_RX_CNT_MASK 0xff ++#define SPI_CTL_START BIT(8) ++ ++#define MT7621_SPI_MASTER 0x28 ++#define MASTER_MORE_BUFMODE BIT(2) ++#define MASTER_FULL_DUPLEX BIT(10) ++#define MASTER_RS_CLK_SEL GENMASK(27, 16) ++#define MASTER_RS_CLK_SEL_SHIFT 16 ++#define MASTER_RS_SLAVE_SEL GENMASK(31, 29) ++ ++#define MT7621_SPI_MOREBUF 0x2c ++#define MT7621_SPI_POLAR 0x38 ++#define MT7621_SPI_SPACE 0x3c ++ ++#define MT7621_CPHA BIT(5) ++#define MT7621_CPOL BIT(4) ++#define MT7621_LSB_FIRST BIT(3) ++ ++struct mt7621_spi { ++ struct spi_controller *master; ++ void __iomem *base; ++ unsigned int sys_freq; ++ unsigned int speed; ++ struct clk *clk; ++ int pending_write; ++}; ++ ++static inline struct mt7621_spi *spidev_to_mt7621_spi(struct spi_device *spi) ++{ ++ return spi_controller_get_devdata(spi->master); ++} ++ ++static inline u32 mt7621_spi_read(struct mt7621_spi *rs, u32 reg) ++{ ++ return ioread32(rs->base + reg); ++} ++ ++static inline void mt7621_spi_write(struct mt7621_spi *rs, u32 reg, u32 val) ++{ ++ iowrite32(val, rs->base + reg); ++} ++ ++static void mt7621_spi_set_cs(struct spi_device *spi, int enable) ++{ ++ struct mt7621_spi *rs = spidev_to_mt7621_spi(spi); ++ int cs = spi->chip_select; ++ u32 polar = 0; ++ u32 master; ++ ++ /* ++ * Select SPI device 7, enable "more buffer mode" and disable ++ * full-duplex (only half-duplex really works on this chip ++ * reliably) ++ */ ++ master = mt7621_spi_read(rs, MT7621_SPI_MASTER); ++ master |= MASTER_RS_SLAVE_SEL | MASTER_MORE_BUFMODE; ++ master &= ~MASTER_FULL_DUPLEX; ++ mt7621_spi_write(rs, MT7621_SPI_MASTER, master); ++ ++ rs->pending_write = 0; ++ ++ if (enable) ++ polar = BIT(cs); ++ mt7621_spi_write(rs, MT7621_SPI_POLAR, polar); ++} ++ ++static int mt7621_spi_prepare(struct spi_device *spi, unsigned int speed) ++{ ++ struct mt7621_spi *rs = spidev_to_mt7621_spi(spi); ++ u32 rate; ++ u32 reg; ++ ++ dev_dbg(&spi->dev, "speed:%u\n", speed); ++ ++ rate = DIV_ROUND_UP(rs->sys_freq, speed); ++ dev_dbg(&spi->dev, "rate-1:%u\n", rate); ++ ++ if (rate > 4097) ++ return -EINVAL; ++ ++ if (rate < 2) ++ rate = 2; ++ ++ reg = mt7621_spi_read(rs, MT7621_SPI_MASTER); ++ reg &= ~MASTER_RS_CLK_SEL; ++ reg |= (rate - 2) << MASTER_RS_CLK_SEL_SHIFT; ++ rs->speed = speed; ++ ++ reg &= ~MT7621_LSB_FIRST; ++ if (spi->mode & SPI_LSB_FIRST) ++ reg |= MT7621_LSB_FIRST; ++ ++ /* ++ * This SPI controller seems to be tested on SPI flash only and some ++ * bits are swizzled under other SPI modes probably due to incorrect ++ * wiring inside the silicon. Only mode 0 works correctly. ++ */ ++ reg &= ~(MT7621_CPHA | MT7621_CPOL); ++ ++ mt7621_spi_write(rs, MT7621_SPI_MASTER, reg); ++ ++ return 0; ++} ++ ++static inline int mt7621_spi_wait_till_ready(struct mt7621_spi *rs) ++{ ++ int i; ++ ++ for (i = 0; i < RALINK_SPI_WAIT_MAX_LOOP; i++) { ++ u32 status; ++ ++ status = mt7621_spi_read(rs, MT7621_SPI_TRANS); ++ if ((status & SPITRANS_BUSY) == 0) ++ return 0; ++ cpu_relax(); ++ udelay(1); ++ } ++ ++ return -ETIMEDOUT; ++} ++ ++static void mt7621_spi_read_half_duplex(struct mt7621_spi *rs, ++ int rx_len, u8 *buf) ++{ ++ int tx_len; ++ ++ /* ++ * Combine with any pending write, and perform one or more half-duplex ++ * transactions reading 'len' bytes. Data to be written is already in ++ * MT7621_SPI_DATA. ++ */ ++ tx_len = rs->pending_write; ++ rs->pending_write = 0; ++ ++ while (rx_len || tx_len) { ++ int i; ++ u32 val = (min(tx_len, 4) * 8) << 24; ++ int rx = min(rx_len, 32); ++ ++ if (tx_len > 4) ++ val |= (tx_len - 4) * 8; ++ val |= (rx * 8) << 12; ++ mt7621_spi_write(rs, MT7621_SPI_MOREBUF, val); ++ ++ tx_len = 0; ++ ++ val = mt7621_spi_read(rs, MT7621_SPI_TRANS); ++ val |= SPI_CTL_START; ++ mt7621_spi_write(rs, MT7621_SPI_TRANS, val); ++ ++ mt7621_spi_wait_till_ready(rs); ++ ++ for (i = 0; i < rx; i++) { ++ if ((i % 4) == 0) ++ val = mt7621_spi_read(rs, MT7621_SPI_DATA0 + i); ++ *buf++ = val & 0xff; ++ val >>= 8; ++ } ++ ++ rx_len -= i; ++ } ++} ++ ++static inline void mt7621_spi_flush(struct mt7621_spi *rs) ++{ ++ mt7621_spi_read_half_duplex(rs, 0, NULL); ++} ++ ++static void mt7621_spi_write_half_duplex(struct mt7621_spi *rs, ++ int tx_len, const u8 *buf) ++{ ++ int len = rs->pending_write; ++ int val = 0; ++ ++ if (len & 3) { ++ val = mt7621_spi_read(rs, MT7621_SPI_OPCODE + (len & ~3)); ++ if (len < 4) { ++ val <<= (4 - len) * 8; ++ val = swab32(val); ++ } ++ } ++ ++ while (tx_len > 0) { ++ if (len >= 36) { ++ rs->pending_write = len; ++ mt7621_spi_flush(rs); ++ len = 0; ++ } ++ ++ val |= *buf++ << (8 * (len & 3)); ++ len++; ++ if ((len & 3) == 0) { ++ if (len == 4) ++ /* The byte-order of the opcode is weird! */ ++ val = swab32(val); ++ mt7621_spi_write(rs, MT7621_SPI_OPCODE + len - 4, val); ++ val = 0; ++ } ++ tx_len -= 1; ++ } ++ ++ if (len & 3) { ++ if (len < 4) { ++ val = swab32(val); ++ val >>= (4 - len) * 8; ++ } ++ mt7621_spi_write(rs, MT7621_SPI_OPCODE + (len & ~3), val); ++ } ++ ++ rs->pending_write = len; ++} ++ ++static int mt7621_spi_transfer_one_message(struct spi_controller *master, ++ struct spi_message *m) ++{ ++ struct mt7621_spi *rs = spi_controller_get_devdata(master); ++ struct spi_device *spi = m->spi; ++ unsigned int speed = spi->max_speed_hz; ++ struct spi_transfer *t = NULL; ++ int status = 0; ++ ++ mt7621_spi_wait_till_ready(rs); ++ ++ list_for_each_entry(t, &m->transfers, transfer_list) ++ if (t->speed_hz < speed) ++ speed = t->speed_hz; ++ ++ if (mt7621_spi_prepare(spi, speed)) { ++ status = -EIO; ++ goto msg_done; ++ } ++ ++ /* Assert CS */ ++ mt7621_spi_set_cs(spi, 1); ++ ++ m->actual_length = 0; ++ list_for_each_entry(t, &m->transfers, transfer_list) { ++ if ((t->rx_buf) && (t->tx_buf)) { ++ /* ++ * This controller will shift some extra data out ++ * of spi_opcode if (mosi_bit_cnt > 0) && ++ * (cmd_bit_cnt == 0). So the claimed full-duplex ++ * support is broken since we have no way to read ++ * the MISO value during that bit. ++ */ ++ status = -EIO; ++ goto msg_done; ++ } else if (t->rx_buf) { ++ mt7621_spi_read_half_duplex(rs, t->len, t->rx_buf); ++ } else if (t->tx_buf) { ++ mt7621_spi_write_half_duplex(rs, t->len, t->tx_buf); ++ } ++ m->actual_length += t->len; ++ } ++ ++ /* Flush data and deassert CS */ ++ mt7621_spi_flush(rs); ++ mt7621_spi_set_cs(spi, 0); ++ ++msg_done: ++ m->status = status; ++ spi_finalize_current_message(master); ++ ++ return 0; ++} ++ ++static int mt7621_spi_setup(struct spi_device *spi) ++{ ++ struct mt7621_spi *rs = spidev_to_mt7621_spi(spi); ++ ++ if ((spi->max_speed_hz == 0) || ++ (spi->max_speed_hz > (rs->sys_freq / 2))) ++ spi->max_speed_hz = (rs->sys_freq / 2); ++ ++ if (spi->max_speed_hz < (rs->sys_freq / 4097)) { ++ dev_err(&spi->dev, "setup: requested speed is too low %d Hz\n", ++ spi->max_speed_hz); ++ return -EINVAL; ++ } ++ ++ return 0; ++} ++ ++static const struct of_device_id mt7621_spi_match[] = { ++ { .compatible = "ralink,mt7621-spi" }, ++ {}, ++}; ++MODULE_DEVICE_TABLE(of, mt7621_spi_match); ++ ++static int mt7621_spi_probe(struct platform_device *pdev) ++{ ++ const struct of_device_id *match; ++ struct spi_controller *master; ++ struct mt7621_spi *rs; ++ void __iomem *base; ++ struct resource *r; ++ int status = 0; ++ struct clk *clk; ++ int ret; ++ ++ match = of_match_device(mt7621_spi_match, &pdev->dev); ++ if (!match) ++ return -EINVAL; ++ ++ r = platform_get_resource(pdev, IORESOURCE_MEM, 0); ++ base = devm_ioremap_resource(&pdev->dev, r); ++ if (IS_ERR(base)) ++ return PTR_ERR(base); ++ ++ clk = devm_clk_get(&pdev->dev, NULL); ++ if (IS_ERR(clk)) { ++ dev_err(&pdev->dev, "unable to get SYS clock, err=%d\n", ++ status); ++ return PTR_ERR(clk); ++ } ++ ++ status = clk_prepare_enable(clk); ++ if (status) ++ return status; ++ ++ master = spi_alloc_master(&pdev->dev, sizeof(*rs)); ++ if (!master) { ++ dev_info(&pdev->dev, "master allocation failed\n"); ++ return -ENOMEM; ++ } ++ ++ master->mode_bits = SPI_LSB_FIRST; ++ master->flags = SPI_CONTROLLER_HALF_DUPLEX; ++ master->setup = mt7621_spi_setup; ++ master->transfer_one_message = mt7621_spi_transfer_one_message; ++ master->bits_per_word_mask = SPI_BPW_MASK(8); ++ master->dev.of_node = pdev->dev.of_node; ++ master->num_chipselect = 2; ++ ++ dev_set_drvdata(&pdev->dev, master); ++ ++ rs = spi_controller_get_devdata(master); ++ rs->base = base; ++ rs->clk = clk; ++ rs->master = master; ++ rs->sys_freq = clk_get_rate(rs->clk); ++ rs->pending_write = 0; ++ dev_info(&pdev->dev, "sys_freq: %u\n", rs->sys_freq); ++ ++ ret = device_reset(&pdev->dev); ++ if (ret) { ++ dev_err(&pdev->dev, "SPI reset failed!\n"); ++ return ret; ++ } ++ ++ return devm_spi_register_controller(&pdev->dev, master); ++} ++ ++static int mt7621_spi_remove(struct platform_device *pdev) ++{ ++ struct spi_controller *master; ++ struct mt7621_spi *rs; ++ ++ master = dev_get_drvdata(&pdev->dev); ++ rs = spi_controller_get_devdata(master); ++ ++ clk_disable_unprepare(rs->clk); ++ ++ return 0; ++} ++ ++MODULE_ALIAS("platform:" DRIVER_NAME); ++ ++static struct platform_driver mt7621_spi_driver = { ++ .driver = { ++ .name = DRIVER_NAME, ++ .of_match_table = mt7621_spi_match, ++ }, ++ .probe = mt7621_spi_probe, ++ .remove = mt7621_spi_remove, ++}; ++ ++module_platform_driver(mt7621_spi_driver); ++ ++MODULE_DESCRIPTION("MT7621 SPI driver"); ++MODULE_AUTHOR("Felix Fietkau "); ++MODULE_LICENSE("GPL"); diff --git a/target/linux/ramips/patches-5.4/0044-i2c-MIPS-adds-ralink-I2C-driver.patch b/target/linux/ramips/patches-5.4/0044-i2c-MIPS-adds-ralink-I2C-driver.patch new file mode 100644 index 0000000000..4905aba046 --- /dev/null +++ b/target/linux/ramips/patches-5.4/0044-i2c-MIPS-adds-ralink-I2C-driver.patch @@ -0,0 +1,507 @@ +From 723b8beaabf3c3c4b1ce69480141f1e926f3f3b2 Mon Sep 17 00:00:00 2001 +From: John Crispin +Date: Sun, 27 Jul 2014 09:52:56 +0100 +Subject: [PATCH 44/53] i2c: MIPS: adds ralink I2C driver + +Signed-off-by: John Crispin +--- + .../devicetree/bindings/i2c/i2c-ralink.txt | 27 ++ + drivers/i2c/busses/Kconfig | 4 + + drivers/i2c/busses/Makefile | 1 + + drivers/i2c/busses/i2c-ralink.c | 327 ++++++++++++++++++++ + 4 files changed, 359 insertions(+) + create mode 100644 Documentation/devicetree/bindings/i2c/i2c-ralink.txt + create mode 100644 drivers/i2c/busses/i2c-ralink.c + +--- /dev/null ++++ b/Documentation/devicetree/bindings/i2c/i2c-ralink.txt +@@ -0,0 +1,27 @@ ++I2C for Ralink platforms ++ ++Required properties : ++- compatible : Must be "link,rt3052-i2c" ++- reg: physical base address of the controller and length of memory mapped ++ region. ++- #address-cells = <1>; ++- #size-cells = <0>; ++ ++Optional properties: ++- Child nodes conforming to i2c bus binding ++ ++Example : ++ ++palmbus@10000000 { ++ i2c@900 { ++ compatible = "link,rt3052-i2c"; ++ reg = <0x900 0x100>; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ hwmon@4b { ++ compatible = "national,lm92"; ++ reg = <0x4b>; ++ }; ++ }; ++}; +--- a/drivers/i2c/busses/Kconfig ++++ b/drivers/i2c/busses/Kconfig +@@ -864,6 +864,11 @@ config I2C_RK3X + This driver can also be built as a module. If so, the module will + be called i2c-rk3x. + ++config I2C_RALINK ++ tristate "Ralink I2C Controller" ++ depends on RALINK && !SOC_MT7621 ++ select OF_I2C ++ + config HAVE_S3C2410_I2C + bool + help +--- a/drivers/i2c/busses/Makefile ++++ b/drivers/i2c/busses/Makefile +@@ -84,6 +84,7 @@ obj-$(CONFIG_I2C_PNX) += i2c-pnx.o + obj-$(CONFIG_I2C_PUV3) += i2c-puv3.o + obj-$(CONFIG_I2C_PXA) += i2c-pxa.o + obj-$(CONFIG_I2C_PXA_PCI) += i2c-pxa-pci.o ++obj-$(CONFIG_I2C_RALINK) += i2c-ralink.o + obj-$(CONFIG_I2C_QUP) += i2c-qup.o + obj-$(CONFIG_I2C_RIIC) += i2c-riic.o + obj-$(CONFIG_I2C_RK3X) += i2c-rk3x.o +--- /dev/null ++++ b/drivers/i2c/busses/i2c-ralink.c +@@ -0,0 +1,435 @@ ++/* ++ * drivers/i2c/busses/i2c-ralink.c ++ * ++ * Copyright (C) 2013 Steven Liu ++ * Copyright (C) 2016 Michael Lee ++ * ++ * Improve driver for i2cdetect from i2c-tools to detect i2c devices on the bus. ++ * (C) 2014 Sittisak ++ * ++ * This software is licensed under the terms of the GNU General Public ++ * License version 2, as published by the Free Software Foundation, and ++ * may be copied, distributed, and modified under those terms. ++ * ++ * This program is distributed in the hope that it will be useful, ++ * but WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the ++ * GNU General Public License for more details. ++ * ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#define REG_CONFIG_REG 0x00 ++#define REG_CLKDIV_REG 0x04 ++#define REG_DEVADDR_REG 0x08 ++#define REG_ADDR_REG 0x0C ++#define REG_DATAOUT_REG 0x10 ++#define REG_DATAIN_REG 0x14 ++#define REG_STATUS_REG 0x18 ++#define REG_STARTXFR_REG 0x1C ++#define REG_BYTECNT_REG 0x20 ++ ++/* REG_CONFIG_REG */ ++#define I2C_ADDRLEN_OFFSET 5 ++#define I2C_DEVADLEN_OFFSET 2 ++#define I2C_ADDRLEN_MASK 0x3 ++#define I2C_ADDR_DIS BIT(1) ++#define I2C_DEVADDR_DIS BIT(0) ++#define I2C_ADDRLEN_8 (7 << I2C_ADDRLEN_OFFSET) ++#define I2C_DEVADLEN_7 (6 << I2C_DEVADLEN_OFFSET) ++#define I2C_CONF_DEFAULT (I2C_ADDRLEN_8 | I2C_DEVADLEN_7) ++ ++/* REG_CLKDIV_REG */ ++#define I2C_CLKDIV_MASK 0xffff ++ ++/* REG_DEVADDR_REG */ ++#define I2C_DEVADDR_MASK 0x7f ++ ++/* REG_ADDR_REG */ ++#define I2C_ADDR_MASK 0xff ++ ++/* REG_STATUS_REG */ ++#define I2C_STARTERR BIT(4) ++#define I2C_ACKERR BIT(3) ++#define I2C_DATARDY BIT(2) ++#define I2C_SDOEMPTY BIT(1) ++#define I2C_BUSY BIT(0) ++ ++/* REG_STARTXFR_REG */ ++#define NOSTOP_CMD BIT(2) ++#define NODATA_CMD BIT(1) ++#define READ_CMD BIT(0) ++ ++/* REG_BYTECNT_REG */ ++#define BYTECNT_MAX 64 ++#define SET_BYTECNT(x) (x - 1) ++ ++/* timeout waiting for I2C devices to respond (clock streching) */ ++#define TIMEOUT_MS 1000 ++#define DELAY_INTERVAL_US 100 ++ ++struct rt_i2c { ++ void __iomem *base; ++ struct clk *clk; ++ struct device *dev; ++ struct i2c_adapter adap; ++ u32 cur_clk; ++ u32 clk_div; ++ u32 flags; ++}; ++ ++static void rt_i2c_w32(struct rt_i2c *i2c, u32 val, unsigned reg) ++{ ++ iowrite32(val, i2c->base + reg); ++} ++ ++static u32 rt_i2c_r32(struct rt_i2c *i2c, unsigned reg) ++{ ++ return ioread32(i2c->base + reg); ++} ++ ++static int poll_down_timeout(void __iomem *addr, u32 mask) ++{ ++ unsigned long timeout = jiffies + msecs_to_jiffies(TIMEOUT_MS); ++ ++ do { ++ if (!(readl_relaxed(addr) & mask)) ++ return 0; ++ ++ usleep_range(DELAY_INTERVAL_US, DELAY_INTERVAL_US + 50); ++ } while (time_before(jiffies, timeout)); ++ ++ return (readl_relaxed(addr) & mask) ? -EAGAIN : 0; ++} ++ ++static int rt_i2c_wait_idle(struct rt_i2c *i2c) ++{ ++ int ret; ++ ++ ret = poll_down_timeout(i2c->base + REG_STATUS_REG, I2C_BUSY); ++ if (ret < 0) ++ dev_dbg(i2c->dev, "idle err(%d)\n", ret); ++ ++ return ret; ++} ++ ++static int poll_up_timeout(void __iomem *addr, u32 mask) ++{ ++ unsigned long timeout = jiffies + msecs_to_jiffies(TIMEOUT_MS); ++ u32 status; ++ ++ do { ++ status = readl_relaxed(addr); ++ ++ /* check error status */ ++ if (status & I2C_STARTERR) ++ return -EAGAIN; ++ else if (status & I2C_ACKERR) ++ return -ENXIO; ++ else if (status & mask) ++ return 0; ++ ++ usleep_range(DELAY_INTERVAL_US, DELAY_INTERVAL_US + 50); ++ } while (time_before(jiffies, timeout)); ++ ++ return -ETIMEDOUT; ++} ++ ++static int rt_i2c_wait_rx_done(struct rt_i2c *i2c) ++{ ++ int ret; ++ ++ ret = poll_up_timeout(i2c->base + REG_STATUS_REG, I2C_DATARDY); ++ if (ret < 0) ++ dev_dbg(i2c->dev, "rx err(%d)\n", ret); ++ ++ return ret; ++} ++ ++static int rt_i2c_wait_tx_done(struct rt_i2c *i2c) ++{ ++ int ret; ++ ++ ret = poll_up_timeout(i2c->base + REG_STATUS_REG, I2C_SDOEMPTY); ++ if (ret < 0) ++ dev_dbg(i2c->dev, "tx err(%d)\n", ret); ++ ++ return ret; ++} ++ ++static void rt_i2c_reset(struct rt_i2c *i2c) ++{ ++ device_reset(i2c->adap.dev.parent); ++ barrier(); ++ rt_i2c_w32(i2c, i2c->clk_div, REG_CLKDIV_REG); ++} ++ ++static void rt_i2c_dump_reg(struct rt_i2c *i2c) ++{ ++ dev_dbg(i2c->dev, "conf %08x, clkdiv %08x, devaddr %08x, " \ ++ "addr %08x, dataout %08x, datain %08x, " \ ++ "status %08x, startxfr %08x, bytecnt %08x\n", ++ rt_i2c_r32(i2c, REG_CONFIG_REG), ++ rt_i2c_r32(i2c, REG_CLKDIV_REG), ++ rt_i2c_r32(i2c, REG_DEVADDR_REG), ++ rt_i2c_r32(i2c, REG_ADDR_REG), ++ rt_i2c_r32(i2c, REG_DATAOUT_REG), ++ rt_i2c_r32(i2c, REG_DATAIN_REG), ++ rt_i2c_r32(i2c, REG_STATUS_REG), ++ rt_i2c_r32(i2c, REG_STARTXFR_REG), ++ rt_i2c_r32(i2c, REG_BYTECNT_REG)); ++} ++ ++static int rt_i2c_master_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs, ++ int num) ++{ ++ struct rt_i2c *i2c; ++ struct i2c_msg *pmsg; ++ unsigned char addr; ++ int i, j, ret; ++ u32 cmd; ++ ++ i2c = i2c_get_adapdata(adap); ++ ++ for (i = 0; i < num; i++) { ++ pmsg = &msgs[i]; ++ if (i == (num - 1)) ++ cmd = 0; ++ else ++ cmd = NOSTOP_CMD; ++ ++ dev_dbg(i2c->dev, "addr: 0x%x, len: %d, flags: 0x%x, stop: %d\n", ++ pmsg->addr, pmsg->len, pmsg->flags, ++ (cmd == 0)? 1 : 0); ++ ++ /* wait hardware idle */ ++ if ((ret = rt_i2c_wait_idle(i2c))) ++ goto err_timeout; ++ ++ if (pmsg->flags & I2C_M_TEN) { ++ rt_i2c_w32(i2c, I2C_CONF_DEFAULT, REG_CONFIG_REG); ++ /* 10 bits address */ ++ addr = 0x78 | ((pmsg->addr >> 8) & 0x03); ++ rt_i2c_w32(i2c, addr & I2C_DEVADDR_MASK, ++ REG_DEVADDR_REG); ++ rt_i2c_w32(i2c, pmsg->addr & I2C_ADDR_MASK, ++ REG_ADDR_REG); ++ } else { ++ rt_i2c_w32(i2c, I2C_CONF_DEFAULT | I2C_ADDR_DIS, ++ REG_CONFIG_REG); ++ /* 7 bits address */ ++ rt_i2c_w32(i2c, pmsg->addr & I2C_DEVADDR_MASK, ++ REG_DEVADDR_REG); ++ } ++ ++ /* buffer length */ ++ if (pmsg->len == 0) ++ cmd |= NODATA_CMD; ++ else ++ rt_i2c_w32(i2c, SET_BYTECNT(pmsg->len), ++ REG_BYTECNT_REG); ++ ++ j = 0; ++ if (pmsg->flags & I2C_M_RD) { ++ cmd |= READ_CMD; ++ /* start transfer */ ++ barrier(); ++ rt_i2c_w32(i2c, cmd, REG_STARTXFR_REG); ++ do { ++ /* wait */ ++ if ((ret = rt_i2c_wait_rx_done(i2c))) ++ goto err_timeout; ++ /* read data */ ++ if (pmsg->len) ++ pmsg->buf[j] = rt_i2c_r32(i2c, ++ REG_DATAIN_REG); ++ j++; ++ } while (j < pmsg->len); ++ } else { ++ do { ++ /* write data */ ++ if (pmsg->len) ++ rt_i2c_w32(i2c, pmsg->buf[j], ++ REG_DATAOUT_REG); ++ /* start transfer */ ++ if (j == 0) { ++ barrier(); ++ rt_i2c_w32(i2c, cmd, REG_STARTXFR_REG); ++ } ++ /* wait */ ++ if ((ret = rt_i2c_wait_tx_done(i2c))) ++ goto err_timeout; ++ j++; ++ } while (j < pmsg->len); ++ } ++ } ++ /* the return value is number of executed messages */ ++ ret = i; ++ ++ return ret; ++ ++err_timeout: ++ rt_i2c_dump_reg(i2c); ++ rt_i2c_reset(i2c); ++ return ret; ++} ++ ++static u32 rt_i2c_func(struct i2c_adapter *a) ++{ ++ return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL; ++} ++ ++static const struct i2c_algorithm rt_i2c_algo = { ++ .master_xfer = rt_i2c_master_xfer, ++ .functionality = rt_i2c_func, ++}; ++ ++static const struct of_device_id i2c_rt_dt_ids[] = { ++ { .compatible = "ralink,rt2880-i2c" }, ++ { /* sentinel */ } ++}; ++ ++MODULE_DEVICE_TABLE(of, i2c_rt_dt_ids); ++ ++static struct i2c_adapter_quirks rt_i2c_quirks = { ++ .max_write_len = BYTECNT_MAX, ++ .max_read_len = BYTECNT_MAX, ++}; ++ ++static int rt_i2c_init(struct rt_i2c *i2c) ++{ ++ u32 reg; ++ ++ /* i2c_sclk = periph_clk / ((2 * clk_div) + 5) */ ++ i2c->clk_div = (clk_get_rate(i2c->clk) - (5 * i2c->cur_clk)) / ++ (2 * i2c->cur_clk); ++ if (i2c->clk_div < 8) ++ i2c->clk_div = 8; ++ if (i2c->clk_div > I2C_CLKDIV_MASK) ++ i2c->clk_div = I2C_CLKDIV_MASK; ++ ++ /* check support combinde/repeated start message */ ++ rt_i2c_w32(i2c, NOSTOP_CMD, REG_STARTXFR_REG); ++ reg = rt_i2c_r32(i2c, REG_STARTXFR_REG) & NOSTOP_CMD; ++ ++ rt_i2c_reset(i2c); ++ ++ return reg; ++} ++ ++static int rt_i2c_probe(struct platform_device *pdev) ++{ ++ struct resource *res; ++ struct rt_i2c *i2c; ++ struct i2c_adapter *adap; ++ const struct of_device_id *match; ++ int ret, restart; ++ ++ match = of_match_device(i2c_rt_dt_ids, &pdev->dev); ++ ++ res = platform_get_resource(pdev, IORESOURCE_MEM, 0); ++ if (!res) { ++ dev_err(&pdev->dev, "no memory resource found\n"); ++ return -ENODEV; ++ } ++ ++ i2c = devm_kzalloc(&pdev->dev, sizeof(struct rt_i2c), GFP_KERNEL); ++ if (!i2c) { ++ dev_err(&pdev->dev, "failed to allocate i2c_adapter\n"); ++ return -ENOMEM; ++ } ++ ++ i2c->base = devm_ioremap_resource(&pdev->dev, res); ++ if (IS_ERR(i2c->base)) ++ return PTR_ERR(i2c->base); ++ ++ i2c->clk = devm_clk_get(&pdev->dev, NULL); ++ if (IS_ERR(i2c->clk)) { ++ dev_err(&pdev->dev, "no clock defined\n"); ++ return -ENODEV; ++ } ++ clk_prepare_enable(i2c->clk); ++ i2c->dev = &pdev->dev; ++ ++ if (of_property_read_u32(pdev->dev.of_node, ++ "clock-frequency", &i2c->cur_clk)) ++ i2c->cur_clk = 100000; ++ ++ adap = &i2c->adap; ++ adap->owner = THIS_MODULE; ++ adap->class = I2C_CLASS_HWMON | I2C_CLASS_SPD; ++ adap->algo = &rt_i2c_algo; ++ adap->retries = 3; ++ adap->dev.parent = &pdev->dev; ++ i2c_set_adapdata(adap, i2c); ++ adap->dev.of_node = pdev->dev.of_node; ++ strlcpy(adap->name, dev_name(&pdev->dev), sizeof(adap->name)); ++ adap->quirks = &rt_i2c_quirks; ++ ++ platform_set_drvdata(pdev, i2c); ++ ++ restart = rt_i2c_init(i2c); ++ ++ ret = i2c_add_adapter(adap); ++ if (ret < 0) { ++ dev_err(&pdev->dev, "failed to add adapter\n"); ++ clk_disable_unprepare(i2c->clk); ++ return ret; ++ } ++ ++ dev_info(&pdev->dev, "clock %uKHz, re-start %ssupport\n", ++ i2c->cur_clk/1000, restart ? "" : "not "); ++ ++ return ret; ++} ++ ++static int rt_i2c_remove(struct platform_device *pdev) ++{ ++ struct rt_i2c *i2c = platform_get_drvdata(pdev); ++ ++ i2c_del_adapter(&i2c->adap); ++ clk_disable_unprepare(i2c->clk); ++ ++ return 0; ++} ++ ++static struct platform_driver rt_i2c_driver = { ++ .probe = rt_i2c_probe, ++ .remove = rt_i2c_remove, ++ .driver = { ++ .owner = THIS_MODULE, ++ .name = "i2c-ralink", ++ .of_match_table = i2c_rt_dt_ids, ++ }, ++}; ++ ++static int __init i2c_rt_init (void) ++{ ++ return platform_driver_register(&rt_i2c_driver); ++} ++subsys_initcall(i2c_rt_init); ++ ++static void __exit i2c_rt_exit (void) ++{ ++ platform_driver_unregister(&rt_i2c_driver); ++} ++module_exit(i2c_rt_exit); ++ ++MODULE_AUTHOR("Steven Liu "); ++MODULE_DESCRIPTION("Ralink I2c host driver"); ++MODULE_LICENSE("GPL"); ++MODULE_ALIAS("platform:Ralink-I2C"); diff --git a/target/linux/ramips/patches-5.4/0045-i2c-add-mt7621-driver.patch b/target/linux/ramips/patches-5.4/0045-i2c-add-mt7621-driver.patch new file mode 100644 index 0000000000..a848085520 --- /dev/null +++ b/target/linux/ramips/patches-5.4/0045-i2c-add-mt7621-driver.patch @@ -0,0 +1,473 @@ +From d5c54ff3d1db0a4348fa04d8e78f3bf6063e3afc Mon Sep 17 00:00:00 2001 +From: John Crispin +Date: Mon, 7 Dec 2015 17:21:27 +0100 +Subject: [PATCH 45/53] i2c: add mt7621 driver + +Signed-off-by: John Crispin +--- + drivers/i2c/busses/Kconfig | 4 + + drivers/i2c/busses/Makefile | 1 + + drivers/i2c/busses/i2c-mt7621.c | 303 +++++++++++++++++++++++++++++++++++++++ + 3 files changed, 308 insertions(+) + create mode 100644 drivers/i2c/busses/i2c-mt7621.c + +--- a/drivers/i2c/busses/Kconfig ++++ b/drivers/i2c/busses/Kconfig +@@ -869,6 +869,11 @@ config I2C_RALINK + depends on RALINK && !SOC_MT7621 + select OF_I2C + ++config I2C_MT7621 ++ tristate "MT7621/MT7628 I2C Controller" ++ depends on RALINK && (SOC_MT7620 || SOC_MT7621) ++ select OF_I2C ++ + config HAVE_S3C2410_I2C + bool + help +--- a/drivers/i2c/busses/Makefile ++++ b/drivers/i2c/busses/Makefile +@@ -85,6 +85,7 @@ obj-$(CONFIG_I2C_PUV3) += i2c-puv3.o + obj-$(CONFIG_I2C_PXA) += i2c-pxa.o + obj-$(CONFIG_I2C_PXA_PCI) += i2c-pxa-pci.o + obj-$(CONFIG_I2C_RALINK) += i2c-ralink.o ++obj-$(CONFIG_I2C_MT7621) += i2c-mt7621.o + obj-$(CONFIG_I2C_QUP) += i2c-qup.o + obj-$(CONFIG_I2C_RIIC) += i2c-riic.o + obj-$(CONFIG_I2C_RK3X) += i2c-rk3x.o +--- /dev/null ++++ b/drivers/i2c/busses/i2c-mt7621.c +@@ -0,0 +1,433 @@ ++/* ++ * drivers/i2c/busses/i2c-mt7621.c ++ * ++ * Copyright (C) 2013 Steven Liu ++ * Copyright (C) 2016 Michael Lee ++ * ++ * Improve driver for i2cdetect from i2c-tools to detect i2c devices on the bus. ++ * (C) 2014 Sittisak ++ * ++ * This software is licensed under the terms of the GNU General Public ++ * License version 2, as published by the Free Software Foundation, and ++ * may be copied, distributed, and modified under those terms. ++ * ++ * This program is distributed in the hope that it will be useful, ++ * but WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the ++ * GNU General Public License for more details. ++ * ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#define REG_SM0CFG0 0x08 ++#define REG_SM0DOUT 0x10 ++#define REG_SM0DIN 0x14 ++#define REG_SM0ST 0x18 ++#define REG_SM0AUTO 0x1C ++#define REG_SM0CFG1 0x20 ++#define REG_SM0CFG2 0x28 ++#define REG_SM0CTL0 0x40 ++#define REG_SM0CTL1 0x44 ++#define REG_SM0D0 0x50 ++#define REG_SM0D1 0x54 ++#define REG_PINTEN 0x5C ++#define REG_PINTST 0x60 ++#define REG_PINTCL 0x64 ++ ++/* REG_SM0CFG0 */ ++#define I2C_DEVADDR_MASK 0x7f ++ ++/* REG_SM0ST */ ++#define I2C_DATARDY BIT(2) ++#define I2C_SDOEMPTY BIT(1) ++#define I2C_BUSY BIT(0) ++ ++/* REG_SM0AUTO */ ++#define READ_CMD BIT(0) ++ ++/* REG_SM0CFG1 */ ++#define BYTECNT_MAX 64 ++#define SET_BYTECNT(x) (x - 1) ++ ++/* REG_SM0CFG2 */ ++#define AUTOMODE_EN BIT(0) ++ ++/* REG_SM0CTL0 */ ++#define ODRAIN_HIGH_SM0 BIT(31) ++#define VSYNC_SHIFT 28 ++#define VSYNC_MASK 0x3 ++#define VSYNC_PULSE (0x1 << VSYNC_SHIFT) ++#define VSYNC_RISING (0x2 << VSYNC_SHIFT) ++#define CLK_DIV_SHIFT 16 ++#define CLK_DIV_MASK 0xfff ++#define DEG_CNT_SHIFT 8 ++#define DEG_CNT_MASK 0xff ++#define WAIT_HIGH BIT(6) ++#define DEG_EN BIT(5) ++#define CS_STATUA BIT(4) ++#define SCL_STATUS BIT(3) ++#define SDA_STATUS BIT(2) ++#define SM0_EN BIT(1) ++#define SCL_STRECH BIT(0) ++ ++/* REG_SM0CTL1 */ ++#define ACK_SHIFT 16 ++#define ACK_MASK 0xff ++#define PGLEN_SHIFT 8 ++#define PGLEN_MASK 0x7 ++#define SM0_MODE_SHIFT 4 ++#define SM0_MODE_MASK 0x7 ++#define SM0_MODE_START 0x1 ++#define SM0_MODE_WRITE 0x2 ++#define SM0_MODE_STOP 0x3 ++#define SM0_MODE_READ_NACK 0x4 ++#define SM0_MODE_READ_ACK 0x5 ++#define SM0_TRI_BUSY BIT(0) ++ ++/* timeout waiting for I2C devices to respond (clock streching) */ ++#define TIMEOUT_MS 1000 ++#define DELAY_INTERVAL_US 100 ++ ++struct mtk_i2c { ++ void __iomem *base; ++ struct clk *clk; ++ struct device *dev; ++ struct i2c_adapter adap; ++ u32 cur_clk; ++ u32 clk_div; ++ u32 flags; ++}; ++ ++static void mtk_i2c_w32(struct mtk_i2c *i2c, u32 val, unsigned reg) ++{ ++ iowrite32(val, i2c->base + reg); ++} ++ ++static u32 mtk_i2c_r32(struct mtk_i2c *i2c, unsigned reg) ++{ ++ return ioread32(i2c->base + reg); ++} ++ ++static int poll_down_timeout(void __iomem *addr, u32 mask) ++{ ++ unsigned long timeout = jiffies + msecs_to_jiffies(TIMEOUT_MS); ++ ++ do { ++ if (!(readl_relaxed(addr) & mask)) ++ return 0; ++ ++ usleep_range(DELAY_INTERVAL_US, DELAY_INTERVAL_US + 50); ++ } while (time_before(jiffies, timeout)); ++ ++ return (readl_relaxed(addr) & mask) ? -EAGAIN : 0; ++} ++ ++static int mtk_i2c_wait_idle(struct mtk_i2c *i2c) ++{ ++ int ret; ++ ++ ret = poll_down_timeout(i2c->base + REG_SM0ST, I2C_BUSY); ++ if (ret < 0) ++ dev_dbg(i2c->dev, "idle err(%d)\n", ret); ++ ++ return ret; ++} ++ ++static int poll_up_timeout(void __iomem *addr, u32 mask) ++{ ++ unsigned long timeout = jiffies + msecs_to_jiffies(TIMEOUT_MS); ++ u32 status; ++ ++ do { ++ status = readl_relaxed(addr); ++ if (status & mask) ++ return 0; ++ usleep_range(DELAY_INTERVAL_US, DELAY_INTERVAL_US + 50); ++ } while (time_before(jiffies, timeout)); ++ ++ return -ETIMEDOUT; ++} ++ ++static int mtk_i2c_wait_rx_done(struct mtk_i2c *i2c) ++{ ++ int ret; ++ ++ ret = poll_up_timeout(i2c->base + REG_SM0ST, I2C_DATARDY); ++ if (ret < 0) ++ dev_dbg(i2c->dev, "rx err(%d)\n", ret); ++ ++ return ret; ++} ++ ++static int mtk_i2c_wait_tx_done(struct mtk_i2c *i2c) ++{ ++ int ret; ++ ++ ret = poll_up_timeout(i2c->base + REG_SM0ST, I2C_SDOEMPTY); ++ if (ret < 0) ++ dev_dbg(i2c->dev, "tx err(%d)\n", ret); ++ ++ return ret; ++} ++ ++static void mtk_i2c_reset(struct mtk_i2c *i2c) ++{ ++ u32 reg; ++ device_reset(i2c->adap.dev.parent); ++ barrier(); ++ ++ /* ctrl0 */ ++ reg = ODRAIN_HIGH_SM0 | VSYNC_PULSE | (i2c->clk_div << CLK_DIV_SHIFT) | ++ WAIT_HIGH | SM0_EN; ++ mtk_i2c_w32(i2c, reg, REG_SM0CTL0); ++ ++ /* auto mode */ ++ mtk_i2c_w32(i2c, AUTOMODE_EN, REG_SM0CFG2); ++} ++ ++static void mtk_i2c_dump_reg(struct mtk_i2c *i2c) ++{ ++ dev_dbg(i2c->dev, "cfg0 %08x, dout %08x, din %08x, " \ ++ "status %08x, auto %08x, cfg1 %08x, " \ ++ "cfg2 %08x, ctl0 %08x, ctl1 %08x\n", ++ mtk_i2c_r32(i2c, REG_SM0CFG0), ++ mtk_i2c_r32(i2c, REG_SM0DOUT), ++ mtk_i2c_r32(i2c, REG_SM0DIN), ++ mtk_i2c_r32(i2c, REG_SM0ST), ++ mtk_i2c_r32(i2c, REG_SM0AUTO), ++ mtk_i2c_r32(i2c, REG_SM0CFG1), ++ mtk_i2c_r32(i2c, REG_SM0CFG2), ++ mtk_i2c_r32(i2c, REG_SM0CTL0), ++ mtk_i2c_r32(i2c, REG_SM0CTL1)); ++} ++ ++static int mtk_i2c_master_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs, ++ int num) ++{ ++ struct mtk_i2c *i2c; ++ struct i2c_msg *pmsg; ++ int i, j, ret; ++ u32 cmd; ++ ++ i2c = i2c_get_adapdata(adap); ++ ++ for (i = 0; i < num; i++) { ++ pmsg = &msgs[i]; ++ cmd = 0; ++ ++ dev_dbg(i2c->dev, "addr: 0x%x, len: %d, flags: 0x%x\n", ++ pmsg->addr, pmsg->len, pmsg->flags); ++ ++ /* wait hardware idle */ ++ if ((ret = mtk_i2c_wait_idle(i2c))) ++ goto err_timeout; ++ ++ if (pmsg->flags & I2C_M_TEN) { ++ dev_dbg(i2c->dev, "10 bits addr not supported\n"); ++ return -EINVAL; ++ } else { ++ /* 7 bits address */ ++ mtk_i2c_w32(i2c, pmsg->addr & I2C_DEVADDR_MASK, ++ REG_SM0CFG0); ++ } ++ ++ /* buffer length */ ++ if (pmsg->len == 0) { ++ dev_dbg(i2c->dev, "length is 0\n"); ++ return -EINVAL; ++ } else ++ mtk_i2c_w32(i2c, SET_BYTECNT(pmsg->len), ++ REG_SM0CFG1); ++ ++ j = 0; ++ if (pmsg->flags & I2C_M_RD) { ++ cmd |= READ_CMD; ++ /* start transfer */ ++ barrier(); ++ mtk_i2c_w32(i2c, cmd, REG_SM0AUTO); ++ do { ++ /* wait */ ++ if ((ret = mtk_i2c_wait_rx_done(i2c))) ++ goto err_timeout; ++ /* read data */ ++ if (pmsg->len) ++ pmsg->buf[j] = mtk_i2c_r32(i2c, ++ REG_SM0DIN); ++ j++; ++ } while (j < pmsg->len); ++ } else { ++ do { ++ /* write data */ ++ if (pmsg->len) ++ mtk_i2c_w32(i2c, pmsg->buf[j], ++ REG_SM0DOUT); ++ /* start transfer */ ++ if (j == 0) { ++ barrier(); ++ mtk_i2c_w32(i2c, cmd, REG_SM0AUTO); ++ } ++ /* wait */ ++ if ((ret = mtk_i2c_wait_tx_done(i2c))) ++ goto err_timeout; ++ j++; ++ } while (j < pmsg->len); ++ } ++ } ++ /* the return value is number of executed messages */ ++ ret = i; ++ ++ return ret; ++ ++err_timeout: ++ mtk_i2c_dump_reg(i2c); ++ mtk_i2c_reset(i2c); ++ return ret; ++} ++ ++static u32 mtk_i2c_func(struct i2c_adapter *a) ++{ ++ return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL; ++} ++ ++static const struct i2c_algorithm mtk_i2c_algo = { ++ .master_xfer = mtk_i2c_master_xfer, ++ .functionality = mtk_i2c_func, ++}; ++ ++static const struct of_device_id i2c_mtk_dt_ids[] = { ++ { .compatible = "mediatek,mt7621-i2c" }, ++ { /* sentinel */ } ++}; ++ ++MODULE_DEVICE_TABLE(of, i2c_mtk_dt_ids); ++ ++static struct i2c_adapter_quirks mtk_i2c_quirks = { ++ .max_write_len = BYTECNT_MAX, ++ .max_read_len = BYTECNT_MAX, ++}; ++ ++static void mtk_i2c_init(struct mtk_i2c *i2c) ++{ ++ i2c->clk_div = clk_get_rate(i2c->clk) / i2c->cur_clk; ++ if (i2c->clk_div > CLK_DIV_MASK) ++ i2c->clk_div = CLK_DIV_MASK; ++ ++ mtk_i2c_reset(i2c); ++} ++ ++static int mtk_i2c_probe(struct platform_device *pdev) ++{ ++ struct resource *res; ++ struct mtk_i2c *i2c; ++ struct i2c_adapter *adap; ++ const struct of_device_id *match; ++ int ret; ++ ++ match = of_match_device(i2c_mtk_dt_ids, &pdev->dev); ++ ++ res = platform_get_resource(pdev, IORESOURCE_MEM, 0); ++ if (!res) { ++ dev_err(&pdev->dev, "no memory resource found\n"); ++ return -ENODEV; ++ } ++ ++ i2c = devm_kzalloc(&pdev->dev, sizeof(struct mtk_i2c), GFP_KERNEL); ++ if (!i2c) { ++ dev_err(&pdev->dev, "failed to allocate i2c_adapter\n"); ++ return -ENOMEM; ++ } ++ ++ i2c->base = devm_ioremap_resource(&pdev->dev, res); ++ if (IS_ERR(i2c->base)) ++ return PTR_ERR(i2c->base); ++ ++ i2c->clk = devm_clk_get(&pdev->dev, NULL); ++ if (IS_ERR(i2c->clk)) { ++ dev_err(&pdev->dev, "no clock defined\n"); ++ return -ENODEV; ++ } ++ clk_prepare_enable(i2c->clk); ++ i2c->dev = &pdev->dev; ++ ++ if (of_property_read_u32(pdev->dev.of_node, ++ "clock-frequency", &i2c->cur_clk)) ++ i2c->cur_clk = 100000; ++ ++ adap = &i2c->adap; ++ adap->owner = THIS_MODULE; ++ adap->class = I2C_CLASS_HWMON | I2C_CLASS_SPD; ++ adap->algo = &mtk_i2c_algo; ++ adap->retries = 3; ++ adap->dev.parent = &pdev->dev; ++ i2c_set_adapdata(adap, i2c); ++ adap->dev.of_node = pdev->dev.of_node; ++ strlcpy(adap->name, dev_name(&pdev->dev), sizeof(adap->name)); ++ adap->quirks = &mtk_i2c_quirks; ++ ++ platform_set_drvdata(pdev, i2c); ++ ++ mtk_i2c_init(i2c); ++ ++ ret = i2c_add_adapter(adap); ++ if (ret < 0) { ++ dev_err(&pdev->dev, "failed to add adapter\n"); ++ clk_disable_unprepare(i2c->clk); ++ return ret; ++ } ++ ++ dev_info(&pdev->dev, "clock %uKHz, re-start not support\n", ++ i2c->cur_clk/1000); ++ ++ return ret; ++} ++ ++static int mtk_i2c_remove(struct platform_device *pdev) ++{ ++ struct mtk_i2c *i2c = platform_get_drvdata(pdev); ++ ++ i2c_del_adapter(&i2c->adap); ++ clk_disable_unprepare(i2c->clk); ++ ++ return 0; ++} ++ ++static struct platform_driver mtk_i2c_driver = { ++ .probe = mtk_i2c_probe, ++ .remove = mtk_i2c_remove, ++ .driver = { ++ .owner = THIS_MODULE, ++ .name = "i2c-mt7621", ++ .of_match_table = i2c_mtk_dt_ids, ++ }, ++}; ++ ++static int __init i2c_mtk_init (void) ++{ ++ return platform_driver_register(&mtk_i2c_driver); ++} ++subsys_initcall(i2c_mtk_init); ++ ++static void __exit i2c_mtk_exit (void) ++{ ++ platform_driver_unregister(&mtk_i2c_driver); ++} ++module_exit(i2c_mtk_exit); ++ ++MODULE_AUTHOR("Steven Liu "); ++MODULE_DESCRIPTION("MT7621 I2c host driver"); ++MODULE_LICENSE("GPL"); ++MODULE_ALIAS("platform:MT7621-I2C"); diff --git a/target/linux/ramips/patches-5.4/0046-mmc-MIPS-ralink-add-sdhci-for-mt7620a-SoC.patch b/target/linux/ramips/patches-5.4/0046-mmc-MIPS-ralink-add-sdhci-for-mt7620a-SoC.patch new file mode 100644 index 0000000000..0535811ea3 --- /dev/null +++ b/target/linux/ramips/patches-5.4/0046-mmc-MIPS-ralink-add-sdhci-for-mt7620a-SoC.patch @@ -0,0 +1,43 @@ +From 23147af14531cbdada194b94120ef8774f46292d Mon Sep 17 00:00:00 2001 +From: John Crispin +Date: Thu, 13 Nov 2014 19:08:40 +0100 +Subject: [PATCH 46/53] mmc: MIPS: ralink: add sdhci for mt7620a SoC + +Signed-off-by: John Crispin +--- + drivers/mmc/host/Kconfig | 2 + + drivers/mmc/host/Makefile | 1 + + drivers/mmc/host/mtk-mmc/Kconfig | 16 + + drivers/mmc/host/mtk-mmc/Makefile | 42 + + drivers/mmc/host/mtk-mmc/board.h | 137 ++ + drivers/mmc/host/mtk-mmc/dbg.c | 347 ++++ + drivers/mmc/host/mtk-mmc/dbg.h | 156 ++ + drivers/mmc/host/mtk-mmc/mt6575_sd.h | 1001 +++++++++++ + drivers/mmc/host/mtk-mmc/sd.c | 3060 ++++++++++++++++++++++++++++++++++ + 9 files changed, 4762 insertions(+) + create mode 100644 drivers/mmc/host/mtk-mmc/Kconfig + create mode 100644 drivers/mmc/host/mtk-mmc/Makefile + create mode 100644 drivers/mmc/host/mtk-mmc/board.h + create mode 100644 drivers/mmc/host/mtk-mmc/dbg.c + create mode 100644 drivers/mmc/host/mtk-mmc/dbg.h + create mode 100644 drivers/mmc/host/mtk-mmc/mt6575_sd.h + create mode 100644 drivers/mmc/host/mtk-mmc/sd.c + +--- a/drivers/mmc/host/Kconfig ++++ b/drivers/mmc/host/Kconfig +@@ -901,3 +901,5 @@ config MMC_SDHCI_XENON + This selects Marvell Xenon eMMC/SD/SDIO SDHCI. + If you have a controller with this interface, say Y or M here. + If unsure, say N. ++ ++source "drivers/mmc/host/mtk-mmc/Kconfig" +--- a/drivers/mmc/host/Makefile ++++ b/drivers/mmc/host/Makefile +@@ -3,6 +3,7 @@ + # Makefile for MMC/SD host controller drivers + # + ++obj-$(CONFIG_MTK_MMC) += mtk-mmc/ + obj-$(CONFIG_MMC_ARMMMCI) += armmmci.o + armmmci-y := mmci.o + armmmci-$(CONFIG_MMC_QCOM_DML) += mmci_qcom_dml.o diff --git a/target/linux/ramips/patches-5.4/0047-DMA-ralink-add-rt2880-dma-engine.patch b/target/linux/ramips/patches-5.4/0047-DMA-ralink-add-rt2880-dma-engine.patch new file mode 100644 index 0000000000..b74a48a220 --- /dev/null +++ b/target/linux/ramips/patches-5.4/0047-DMA-ralink-add-rt2880-dma-engine.patch @@ -0,0 +1,1757 @@ +From f1c4d9e622c800e1f38b3818f933ec7597d1ccfb Mon Sep 17 00:00:00 2001 +From: John Crispin +Date: Sun, 27 Jul 2014 09:29:51 +0100 +Subject: [PATCH 47/53] DMA: ralink: add rt2880 dma engine + +Signed-off-by: John Crispin +--- + drivers/dma/Kconfig | 6 + + drivers/dma/Makefile | 1 + + drivers/dma/ralink-gdma.c | 577 +++++++++++++++++++++++++++++++++++++++++++++ + include/linux/dmaengine.h | 1 + + 4 files changed, 585 insertions(+) + create mode 100644 drivers/dma/ralink-gdma.c + +--- a/drivers/dma/Kconfig ++++ b/drivers/dma/Kconfig +@@ -40,6 +40,18 @@ config ASYNC_TX_ENABLE_CHANNEL_SWITCH + config ARCH_HAS_ASYNC_TX_FIND_CHANNEL + bool + ++config DMA_RALINK ++ tristate "RALINK DMA support" ++ depends on RALINK && !SOC_RT288X ++ select DMA_ENGINE ++ select DMA_VIRTUAL_CHANNELS ++ ++config MTK_HSDMA ++ tristate "MTK HSDMA support" ++ depends on RALINK && SOC_MT7621 ++ select DMA_ENGINE ++ select DMA_VIRTUAL_CHANNELS ++ + config DMA_ENGINE + bool + +--- a/drivers/dma/Makefile ++++ b/drivers/dma/Makefile +@@ -71,6 +71,8 @@ obj-$(CONFIG_TI_EDMA) += edma.o + obj-$(CONFIG_XGENE_DMA) += xgene-dma.o + obj-$(CONFIG_ZX_DMA) += zx_dma.o + obj-$(CONFIG_ST_FDMA) += st_fdma.o ++obj-$(CONFIG_DMA_RALINK) += ralink-gdma.o ++obj-$(CONFIG_MTK_HSDMA) += mtk-hsdma.o + + obj-y += qcom/ + obj-y += xilinx/ +--- /dev/null ++++ b/drivers/dma/ralink-gdma.c +@@ -0,0 +1,928 @@ ++/* ++ * Copyright (C) 2013, Lars-Peter Clausen ++ * GDMA4740 DMAC support ++ * ++ * This program is free software; you can redistribute it and/or modify it ++ * under the terms of the GNU General Public License as published by the ++ * Free Software Foundation; either version 2 of the License, or (at your ++ * option) any later version. ++ * ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#include "virt-dma.h" ++ ++#define GDMA_REG_SRC_ADDR(x) (0x00 + (x) * 0x10) ++#define GDMA_REG_DST_ADDR(x) (0x04 + (x) * 0x10) ++ ++#define GDMA_REG_CTRL0(x) (0x08 + (x) * 0x10) ++#define GDMA_REG_CTRL0_TX_MASK 0xffff ++#define GDMA_REG_CTRL0_TX_SHIFT 16 ++#define GDMA_REG_CTRL0_CURR_MASK 0xff ++#define GDMA_REG_CTRL0_CURR_SHIFT 8 ++#define GDMA_REG_CTRL0_SRC_ADDR_FIXED BIT(7) ++#define GDMA_REG_CTRL0_DST_ADDR_FIXED BIT(6) ++#define GDMA_REG_CTRL0_BURST_MASK 0x7 ++#define GDMA_REG_CTRL0_BURST_SHIFT 3 ++#define GDMA_REG_CTRL0_DONE_INT BIT(2) ++#define GDMA_REG_CTRL0_ENABLE BIT(1) ++#define GDMA_REG_CTRL0_SW_MODE BIT(0) ++ ++#define GDMA_REG_CTRL1(x) (0x0c + (x) * 0x10) ++#define GDMA_REG_CTRL1_SEG_MASK 0xf ++#define GDMA_REG_CTRL1_SEG_SHIFT 22 ++#define GDMA_REG_CTRL1_REQ_MASK 0x3f ++#define GDMA_REG_CTRL1_SRC_REQ_SHIFT 16 ++#define GDMA_REG_CTRL1_DST_REQ_SHIFT 8 ++#define GDMA_REG_CTRL1_CONTINOUS BIT(14) ++#define GDMA_REG_CTRL1_NEXT_MASK 0x1f ++#define GDMA_REG_CTRL1_NEXT_SHIFT 3 ++#define GDMA_REG_CTRL1_COHERENT BIT(2) ++#define GDMA_REG_CTRL1_FAIL BIT(1) ++#define GDMA_REG_CTRL1_MASK BIT(0) ++ ++#define GDMA_REG_UNMASK_INT 0x200 ++#define GDMA_REG_DONE_INT 0x204 ++ ++#define GDMA_REG_GCT 0x220 ++#define GDMA_REG_GCT_CHAN_MASK 0x3 ++#define GDMA_REG_GCT_CHAN_SHIFT 3 ++#define GDMA_REG_GCT_VER_MASK 0x3 ++#define GDMA_REG_GCT_VER_SHIFT 1 ++#define GDMA_REG_GCT_ARBIT_RR BIT(0) ++ ++#define GDMA_REG_REQSTS 0x2a0 ++#define GDMA_REG_ACKSTS 0x2a4 ++#define GDMA_REG_FINSTS 0x2a8 ++ ++/* for RT305X gdma registers */ ++#define GDMA_RT305X_CTRL0_REQ_MASK 0xf ++#define GDMA_RT305X_CTRL0_SRC_REQ_SHIFT 12 ++#define GDMA_RT305X_CTRL0_DST_REQ_SHIFT 8 ++ ++#define GDMA_RT305X_CTRL1_FAIL BIT(4) ++#define GDMA_RT305X_CTRL1_NEXT_MASK 0x7 ++#define GDMA_RT305X_CTRL1_NEXT_SHIFT 1 ++ ++#define GDMA_RT305X_STATUS_INT 0x80 ++#define GDMA_RT305X_STATUS_SIGNAL 0x84 ++#define GDMA_RT305X_GCT 0x88 ++ ++/* for MT7621 gdma registers */ ++#define GDMA_REG_PERF_START(x) (0x230 + (x) * 0x8) ++#define GDMA_REG_PERF_END(x) (0x234 + (x) * 0x8) ++ ++enum gdma_dma_transfer_size { ++ GDMA_TRANSFER_SIZE_4BYTE = 0, ++ GDMA_TRANSFER_SIZE_8BYTE = 1, ++ GDMA_TRANSFER_SIZE_16BYTE = 2, ++ GDMA_TRANSFER_SIZE_32BYTE = 3, ++ GDMA_TRANSFER_SIZE_64BYTE = 4, ++}; ++ ++struct gdma_dma_sg { ++ dma_addr_t src_addr; ++ dma_addr_t dst_addr; ++ u32 len; ++}; ++ ++struct gdma_dma_desc { ++ struct virt_dma_desc vdesc; ++ ++ enum dma_transfer_direction direction; ++ bool cyclic; ++ ++ u32 residue; ++ unsigned int num_sgs; ++ struct gdma_dma_sg sg[]; ++}; ++ ++struct gdma_dmaengine_chan { ++ struct virt_dma_chan vchan; ++ unsigned int id; ++ unsigned int slave_id; ++ ++ dma_addr_t fifo_addr; ++ enum gdma_dma_transfer_size burst_size; ++ ++ struct gdma_dma_desc *desc; ++ unsigned int next_sg; ++}; ++ ++struct gdma_dma_dev { ++ struct dma_device ddev; ++ struct device_dma_parameters dma_parms; ++ struct gdma_data *data; ++ void __iomem *base; ++ struct tasklet_struct task; ++ volatile unsigned long chan_issued; ++ atomic_t cnt; ++ ++ struct gdma_dmaengine_chan chan[]; ++}; ++ ++struct gdma_data ++{ ++ int chancnt; ++ u32 done_int_reg; ++ void (*init)(struct gdma_dma_dev *dma_dev); ++ int (*start_transfer)(struct gdma_dmaengine_chan *chan); ++}; ++ ++static struct gdma_dma_dev *gdma_dma_chan_get_dev( ++ struct gdma_dmaengine_chan *chan) ++{ ++ return container_of(chan->vchan.chan.device, struct gdma_dma_dev, ++ ddev); ++} ++ ++static struct gdma_dmaengine_chan *to_gdma_dma_chan(struct dma_chan *c) ++{ ++ return container_of(c, struct gdma_dmaengine_chan, vchan.chan); ++} ++ ++static struct gdma_dma_desc *to_gdma_dma_desc(struct virt_dma_desc *vdesc) ++{ ++ return container_of(vdesc, struct gdma_dma_desc, vdesc); ++} ++ ++static inline uint32_t gdma_dma_read(struct gdma_dma_dev *dma_dev, ++ unsigned int reg) ++{ ++ return readl(dma_dev->base + reg); ++} ++ ++static inline void gdma_dma_write(struct gdma_dma_dev *dma_dev, ++ unsigned reg, uint32_t val) ++{ ++ writel(val, dma_dev->base + reg); ++} ++ ++static struct gdma_dma_desc *gdma_dma_alloc_desc(unsigned int num_sgs) ++{ ++ return kzalloc(sizeof(struct gdma_dma_desc) + ++ sizeof(struct gdma_dma_sg) * num_sgs, GFP_ATOMIC); ++} ++ ++static enum gdma_dma_transfer_size gdma_dma_maxburst(u32 maxburst) ++{ ++ if (maxburst < 2) ++ return GDMA_TRANSFER_SIZE_4BYTE; ++ else if (maxburst < 4) ++ return GDMA_TRANSFER_SIZE_8BYTE; ++ else if (maxburst < 8) ++ return GDMA_TRANSFER_SIZE_16BYTE; ++ else if (maxburst < 16) ++ return GDMA_TRANSFER_SIZE_32BYTE; ++ else ++ return GDMA_TRANSFER_SIZE_64BYTE; ++} ++ ++static int gdma_dma_config(struct dma_chan *c, ++ struct dma_slave_config *config) ++{ ++ struct gdma_dmaengine_chan *chan = to_gdma_dma_chan(c); ++ struct gdma_dma_dev *dma_dev = gdma_dma_chan_get_dev(chan); ++ ++ if (config->device_fc) { ++ dev_err(dma_dev->ddev.dev, "not support flow controller\n"); ++ return -EINVAL; ++ } ++ ++ switch (config->direction) { ++ case DMA_MEM_TO_DEV: ++ if (config->dst_addr_width != DMA_SLAVE_BUSWIDTH_4_BYTES) { ++ dev_err(dma_dev->ddev.dev, "only support 4 byte buswidth\n"); ++ return -EINVAL; ++ } ++ chan->slave_id = config->slave_id; ++ chan->fifo_addr = config->dst_addr; ++ chan->burst_size = gdma_dma_maxburst(config->dst_maxburst); ++ break; ++ case DMA_DEV_TO_MEM: ++ if (config->src_addr_width != DMA_SLAVE_BUSWIDTH_4_BYTES) { ++ dev_err(dma_dev->ddev.dev, "only support 4 byte buswidth\n"); ++ return -EINVAL; ++ } ++ chan->slave_id = config->slave_id; ++ chan->fifo_addr = config->src_addr; ++ chan->burst_size = gdma_dma_maxburst(config->src_maxburst); ++ break; ++ default: ++ dev_err(dma_dev->ddev.dev, "direction type %d error\n", ++ config->direction); ++ return -EINVAL; ++ } ++ ++ return 0; ++} ++ ++static int gdma_dma_terminate_all(struct dma_chan *c) ++{ ++ struct gdma_dmaengine_chan *chan = to_gdma_dma_chan(c); ++ struct gdma_dma_dev *dma_dev = gdma_dma_chan_get_dev(chan); ++ unsigned long flags, timeout; ++ LIST_HEAD(head); ++ int i = 0; ++ ++ spin_lock_irqsave(&chan->vchan.lock, flags); ++ chan->desc = NULL; ++ clear_bit(chan->id, &dma_dev->chan_issued); ++ vchan_get_all_descriptors(&chan->vchan, &head); ++ spin_unlock_irqrestore(&chan->vchan.lock, flags); ++ ++ vchan_dma_desc_free_list(&chan->vchan, &head); ++ ++ /* wait dma transfer complete */ ++ timeout = jiffies + msecs_to_jiffies(5000); ++ while (gdma_dma_read(dma_dev, GDMA_REG_CTRL0(chan->id)) & ++ GDMA_REG_CTRL0_ENABLE) { ++ if (time_after_eq(jiffies, timeout)) { ++ dev_err(dma_dev->ddev.dev, "chan %d wait timeout\n", ++ chan->id); ++ /* restore to init value */ ++ gdma_dma_write(dma_dev, GDMA_REG_CTRL0(chan->id), 0); ++ break; ++ } ++ cpu_relax(); ++ i++; ++ } ++ ++ if (i) ++ dev_dbg(dma_dev->ddev.dev, "terminate chan %d loops %d\n", ++ chan->id, i); ++ ++ return 0; ++} ++ ++static void rt305x_dump_reg(struct gdma_dma_dev *dma_dev, int id) ++{ ++ dev_dbg(dma_dev->ddev.dev, "chan %d, src %08x, dst %08x, ctr0 %08x, " \ ++ "ctr1 %08x, intr %08x, signal %08x\n", id, ++ gdma_dma_read(dma_dev, GDMA_REG_SRC_ADDR(id)), ++ gdma_dma_read(dma_dev, GDMA_REG_DST_ADDR(id)), ++ gdma_dma_read(dma_dev, GDMA_REG_CTRL0(id)), ++ gdma_dma_read(dma_dev, GDMA_REG_CTRL1(id)), ++ gdma_dma_read(dma_dev, GDMA_RT305X_STATUS_INT), ++ gdma_dma_read(dma_dev, GDMA_RT305X_STATUS_SIGNAL)); ++} ++ ++static int rt305x_gdma_start_transfer(struct gdma_dmaengine_chan *chan) ++{ ++ struct gdma_dma_dev *dma_dev = gdma_dma_chan_get_dev(chan); ++ dma_addr_t src_addr, dst_addr; ++ struct gdma_dma_sg *sg; ++ uint32_t ctrl0, ctrl1; ++ ++ /* verify chan is already stopped */ ++ ctrl0 = gdma_dma_read(dma_dev, GDMA_REG_CTRL0(chan->id)); ++ if (unlikely(ctrl0 & GDMA_REG_CTRL0_ENABLE)) { ++ dev_err(dma_dev->ddev.dev, "chan %d is start(%08x).\n", ++ chan->id, ctrl0); ++ rt305x_dump_reg(dma_dev, chan->id); ++ return -EINVAL; ++ } ++ ++ sg = &chan->desc->sg[chan->next_sg]; ++ if (chan->desc->direction == DMA_MEM_TO_DEV) { ++ src_addr = sg->src_addr; ++ dst_addr = chan->fifo_addr; ++ ctrl0 = GDMA_REG_CTRL0_DST_ADDR_FIXED | \ ++ (8 << GDMA_RT305X_CTRL0_SRC_REQ_SHIFT) | \ ++ (chan->slave_id << GDMA_RT305X_CTRL0_DST_REQ_SHIFT); ++ } else if (chan->desc->direction == DMA_DEV_TO_MEM) { ++ src_addr = chan->fifo_addr; ++ dst_addr = sg->dst_addr; ++ ctrl0 = GDMA_REG_CTRL0_SRC_ADDR_FIXED | \ ++ (chan->slave_id << GDMA_RT305X_CTRL0_SRC_REQ_SHIFT) | \ ++ (8 << GDMA_RT305X_CTRL0_DST_REQ_SHIFT); ++ } else if (chan->desc->direction == DMA_MEM_TO_MEM) { ++ /* ++ * TODO: memcpy function have bugs. sometime it will copy ++ * more 8 bytes data when using dmatest verify. ++ */ ++ src_addr = sg->src_addr; ++ dst_addr = sg->dst_addr; ++ ctrl0 = GDMA_REG_CTRL0_SW_MODE | \ ++ (8 << GDMA_REG_CTRL1_SRC_REQ_SHIFT) | \ ++ (8 << GDMA_REG_CTRL1_DST_REQ_SHIFT); ++ } else { ++ dev_err(dma_dev->ddev.dev, "direction type %d error\n", ++ chan->desc->direction); ++ return -EINVAL; ++ } ++ ++ ctrl0 |= (sg->len << GDMA_REG_CTRL0_TX_SHIFT) | \ ++ (chan->burst_size << GDMA_REG_CTRL0_BURST_SHIFT) | \ ++ GDMA_REG_CTRL0_DONE_INT | GDMA_REG_CTRL0_ENABLE; ++ ctrl1 = chan->id << GDMA_REG_CTRL1_NEXT_SHIFT; ++ ++ chan->next_sg++; ++ gdma_dma_write(dma_dev, GDMA_REG_SRC_ADDR(chan->id), src_addr); ++ gdma_dma_write(dma_dev, GDMA_REG_DST_ADDR(chan->id), dst_addr); ++ gdma_dma_write(dma_dev, GDMA_REG_CTRL1(chan->id), ctrl1); ++ ++ /* make sure next_sg is update */ ++ wmb(); ++ gdma_dma_write(dma_dev, GDMA_REG_CTRL0(chan->id), ctrl0); ++ ++ return 0; ++} ++ ++static void rt3883_dump_reg(struct gdma_dma_dev *dma_dev, int id) ++{ ++ dev_dbg(dma_dev->ddev.dev, "chan %d, src %08x, dst %08x, ctr0 %08x, " \ ++ "ctr1 %08x, unmask %08x, done %08x, " \ ++ "req %08x, ack %08x, fin %08x\n", id, ++ gdma_dma_read(dma_dev, GDMA_REG_SRC_ADDR(id)), ++ gdma_dma_read(dma_dev, GDMA_REG_DST_ADDR(id)), ++ gdma_dma_read(dma_dev, GDMA_REG_CTRL0(id)), ++ gdma_dma_read(dma_dev, GDMA_REG_CTRL1(id)), ++ gdma_dma_read(dma_dev, GDMA_REG_UNMASK_INT), ++ gdma_dma_read(dma_dev, GDMA_REG_DONE_INT), ++ gdma_dma_read(dma_dev, GDMA_REG_REQSTS), ++ gdma_dma_read(dma_dev, GDMA_REG_ACKSTS), ++ gdma_dma_read(dma_dev, GDMA_REG_FINSTS)); ++} ++ ++static int rt3883_gdma_start_transfer(struct gdma_dmaengine_chan *chan) ++{ ++ struct gdma_dma_dev *dma_dev = gdma_dma_chan_get_dev(chan); ++ dma_addr_t src_addr, dst_addr; ++ struct gdma_dma_sg *sg; ++ uint32_t ctrl0, ctrl1; ++ ++ /* verify chan is already stopped */ ++ ctrl0 = gdma_dma_read(dma_dev, GDMA_REG_CTRL0(chan->id)); ++ if (unlikely(ctrl0 & GDMA_REG_CTRL0_ENABLE)) { ++ dev_err(dma_dev->ddev.dev, "chan %d is start(%08x).\n", ++ chan->id, ctrl0); ++ rt3883_dump_reg(dma_dev, chan->id); ++ return -EINVAL; ++ } ++ ++ sg = &chan->desc->sg[chan->next_sg]; ++ if (chan->desc->direction == DMA_MEM_TO_DEV) { ++ src_addr = sg->src_addr; ++ dst_addr = chan->fifo_addr; ++ ctrl0 = GDMA_REG_CTRL0_DST_ADDR_FIXED; ++ ctrl1 = (32 << GDMA_REG_CTRL1_SRC_REQ_SHIFT) | \ ++ (chan->slave_id << GDMA_REG_CTRL1_DST_REQ_SHIFT); ++ } else if (chan->desc->direction == DMA_DEV_TO_MEM) { ++ src_addr = chan->fifo_addr; ++ dst_addr = sg->dst_addr; ++ ctrl0 = GDMA_REG_CTRL0_SRC_ADDR_FIXED; ++ ctrl1 = (chan->slave_id << GDMA_REG_CTRL1_SRC_REQ_SHIFT) | \ ++ (32 << GDMA_REG_CTRL1_DST_REQ_SHIFT) | \ ++ GDMA_REG_CTRL1_COHERENT; ++ } else if (chan->desc->direction == DMA_MEM_TO_MEM) { ++ src_addr = sg->src_addr; ++ dst_addr = sg->dst_addr; ++ ctrl0 = GDMA_REG_CTRL0_SW_MODE; ++ ctrl1 = (32 << GDMA_REG_CTRL1_SRC_REQ_SHIFT) | \ ++ (32 << GDMA_REG_CTRL1_DST_REQ_SHIFT) | \ ++ GDMA_REG_CTRL1_COHERENT; ++ } else { ++ dev_err(dma_dev->ddev.dev, "direction type %d error\n", ++ chan->desc->direction); ++ return -EINVAL; ++ } ++ ++ ctrl0 |= (sg->len << GDMA_REG_CTRL0_TX_SHIFT) | \ ++ (chan->burst_size << GDMA_REG_CTRL0_BURST_SHIFT) | \ ++ GDMA_REG_CTRL0_DONE_INT | GDMA_REG_CTRL0_ENABLE; ++ ctrl1 |= chan->id << GDMA_REG_CTRL1_NEXT_SHIFT; ++ ++ chan->next_sg++; ++ gdma_dma_write(dma_dev, GDMA_REG_SRC_ADDR(chan->id), src_addr); ++ gdma_dma_write(dma_dev, GDMA_REG_DST_ADDR(chan->id), dst_addr); ++ gdma_dma_write(dma_dev, GDMA_REG_CTRL1(chan->id), ctrl1); ++ ++ /* make sure next_sg is update */ ++ wmb(); ++ gdma_dma_write(dma_dev, GDMA_REG_CTRL0(chan->id), ctrl0); ++ ++ return 0; ++} ++ ++static inline int gdma_start_transfer(struct gdma_dma_dev *dma_dev, ++ struct gdma_dmaengine_chan *chan) ++{ ++ return dma_dev->data->start_transfer(chan); ++} ++ ++static int gdma_next_desc(struct gdma_dmaengine_chan *chan) ++{ ++ struct virt_dma_desc *vdesc; ++ ++ vdesc = vchan_next_desc(&chan->vchan); ++ if (!vdesc) { ++ chan->desc = NULL; ++ return 0; ++ } ++ chan->desc = to_gdma_dma_desc(vdesc); ++ chan->next_sg = 0; ++ ++ return 1; ++} ++ ++static void gdma_dma_chan_irq(struct gdma_dma_dev *dma_dev, ++ struct gdma_dmaengine_chan *chan) ++{ ++ struct gdma_dma_desc *desc; ++ unsigned long flags; ++ int chan_issued; ++ ++ chan_issued = 0; ++ spin_lock_irqsave(&chan->vchan.lock, flags); ++ desc = chan->desc; ++ if (desc) { ++ if (desc->cyclic) { ++ vchan_cyclic_callback(&desc->vdesc); ++ if (chan->next_sg == desc->num_sgs) ++ chan->next_sg = 0; ++ chan_issued = 1; ++ } else { ++ desc->residue -= desc->sg[chan->next_sg - 1].len; ++ if (chan->next_sg == desc->num_sgs) { ++ list_del(&desc->vdesc.node); ++ vchan_cookie_complete(&desc->vdesc); ++ chan_issued = gdma_next_desc(chan); ++ } else ++ chan_issued = 1; ++ } ++ } else ++ dev_dbg(dma_dev->ddev.dev, "chan %d no desc to complete\n", ++ chan->id); ++ if (chan_issued) ++ set_bit(chan->id, &dma_dev->chan_issued); ++ spin_unlock_irqrestore(&chan->vchan.lock, flags); ++} ++ ++static irqreturn_t gdma_dma_irq(int irq, void *devid) ++{ ++ struct gdma_dma_dev *dma_dev = devid; ++ u32 done, done_reg; ++ unsigned int i; ++ ++ done_reg = dma_dev->data->done_int_reg; ++ done = gdma_dma_read(dma_dev, done_reg); ++ if (unlikely(!done)) ++ return IRQ_NONE; ++ ++ /* clean done bits */ ++ gdma_dma_write(dma_dev, done_reg, done); ++ ++ i = 0; ++ while (done) { ++ if (done & 0x1) { ++ gdma_dma_chan_irq(dma_dev, &dma_dev->chan[i]); ++ atomic_dec(&dma_dev->cnt); ++ } ++ done >>= 1; ++ i++; ++ } ++ ++ /* start only have work to do */ ++ if (dma_dev->chan_issued) ++ tasklet_schedule(&dma_dev->task); ++ ++ return IRQ_HANDLED; ++} ++ ++static void gdma_dma_issue_pending(struct dma_chan *c) ++{ ++ struct gdma_dmaengine_chan *chan = to_gdma_dma_chan(c); ++ struct gdma_dma_dev *dma_dev = gdma_dma_chan_get_dev(chan); ++ unsigned long flags; ++ ++ spin_lock_irqsave(&chan->vchan.lock, flags); ++ if (vchan_issue_pending(&chan->vchan) && !chan->desc) { ++ if (gdma_next_desc(chan)) { ++ set_bit(chan->id, &dma_dev->chan_issued); ++ tasklet_schedule(&dma_dev->task); ++ } else ++ dev_dbg(dma_dev->ddev.dev, "chan %d no desc to issue\n", ++ chan->id); ++ } ++ spin_unlock_irqrestore(&chan->vchan.lock, flags); ++} ++ ++static struct dma_async_tx_descriptor *gdma_dma_prep_slave_sg( ++ struct dma_chan *c, struct scatterlist *sgl, ++ unsigned int sg_len, enum dma_transfer_direction direction, ++ unsigned long flags, void *context) ++{ ++ struct gdma_dmaengine_chan *chan = to_gdma_dma_chan(c); ++ struct gdma_dma_desc *desc; ++ struct scatterlist *sg; ++ unsigned int i; ++ ++ desc = gdma_dma_alloc_desc(sg_len); ++ if (!desc) { ++ dev_err(c->device->dev, "alloc sg decs error\n"); ++ return NULL; ++ } ++ desc->residue = 0; ++ ++ for_each_sg(sgl, sg, sg_len, i) { ++ if (direction == DMA_MEM_TO_DEV) ++ desc->sg[i].src_addr = sg_dma_address(sg); ++ else if (direction == DMA_DEV_TO_MEM) ++ desc->sg[i].dst_addr = sg_dma_address(sg); ++ else { ++ dev_err(c->device->dev, "direction type %d error\n", ++ direction); ++ goto free_desc; ++ } ++ ++ if (unlikely(sg_dma_len(sg) > GDMA_REG_CTRL0_TX_MASK)) { ++ dev_err(c->device->dev, "sg len too large %d\n", ++ sg_dma_len(sg)); ++ goto free_desc; ++ } ++ desc->sg[i].len = sg_dma_len(sg); ++ desc->residue += sg_dma_len(sg); ++ } ++ ++ desc->num_sgs = sg_len; ++ desc->direction = direction; ++ desc->cyclic = false; ++ ++ return vchan_tx_prep(&chan->vchan, &desc->vdesc, flags); ++ ++free_desc: ++ kfree(desc); ++ return NULL; ++} ++ ++static struct dma_async_tx_descriptor * gdma_dma_prep_dma_memcpy( ++ struct dma_chan *c, dma_addr_t dest, dma_addr_t src, ++ size_t len, unsigned long flags) ++{ ++ struct gdma_dmaengine_chan *chan = to_gdma_dma_chan(c); ++ struct gdma_dma_desc *desc; ++ unsigned int num_periods, i; ++ size_t xfer_count; ++ ++ if (len <= 0) ++ return NULL; ++ ++ chan->burst_size = gdma_dma_maxburst(len >> 2); ++ ++ xfer_count = GDMA_REG_CTRL0_TX_MASK; ++ num_periods = DIV_ROUND_UP(len, xfer_count); ++ ++ desc = gdma_dma_alloc_desc(num_periods); ++ if (!desc) { ++ dev_err(c->device->dev, "alloc memcpy decs error\n"); ++ return NULL; ++ } ++ desc->residue = len; ++ ++ for (i = 0; i < num_periods; i++) { ++ desc->sg[i].src_addr = src; ++ desc->sg[i].dst_addr = dest; ++ if (len > xfer_count) { ++ desc->sg[i].len = xfer_count; ++ } else { ++ desc->sg[i].len = len; ++ } ++ src += desc->sg[i].len; ++ dest += desc->sg[i].len; ++ len -= desc->sg[i].len; ++ } ++ ++ desc->num_sgs = num_periods; ++ desc->direction = DMA_MEM_TO_MEM; ++ desc->cyclic = false; ++ ++ return vchan_tx_prep(&chan->vchan, &desc->vdesc, flags); ++} ++ ++static struct dma_async_tx_descriptor *gdma_dma_prep_dma_cyclic( ++ struct dma_chan *c, dma_addr_t buf_addr, size_t buf_len, ++ size_t period_len, enum dma_transfer_direction direction, ++ unsigned long flags) ++{ ++ struct gdma_dmaengine_chan *chan = to_gdma_dma_chan(c); ++ struct gdma_dma_desc *desc; ++ unsigned int num_periods, i; ++ ++ if (buf_len % period_len) ++ return NULL; ++ ++ if (period_len > GDMA_REG_CTRL0_TX_MASK) { ++ dev_err(c->device->dev, "cyclic len too large %d\n", ++ period_len); ++ return NULL; ++ } ++ ++ num_periods = buf_len / period_len; ++ desc = gdma_dma_alloc_desc(num_periods); ++ if (!desc) { ++ dev_err(c->device->dev, "alloc cyclic decs error\n"); ++ return NULL; ++ } ++ desc->residue = buf_len; ++ ++ for (i = 0; i < num_periods; i++) { ++ if (direction == DMA_MEM_TO_DEV) ++ desc->sg[i].src_addr = buf_addr; ++ else if (direction == DMA_DEV_TO_MEM) ++ desc->sg[i].dst_addr = buf_addr; ++ else { ++ dev_err(c->device->dev, "direction type %d error\n", ++ direction); ++ goto free_desc; ++ } ++ desc->sg[i].len = period_len; ++ buf_addr += period_len; ++ } ++ ++ desc->num_sgs = num_periods; ++ desc->direction = direction; ++ desc->cyclic = true; ++ ++ return vchan_tx_prep(&chan->vchan, &desc->vdesc, flags); ++ ++free_desc: ++ kfree(desc); ++ return NULL; ++} ++ ++static enum dma_status gdma_dma_tx_status(struct dma_chan *c, ++ dma_cookie_t cookie, struct dma_tx_state *state) ++{ ++ struct gdma_dmaengine_chan *chan = to_gdma_dma_chan(c); ++ struct virt_dma_desc *vdesc; ++ enum dma_status status; ++ unsigned long flags; ++ struct gdma_dma_desc *desc; ++ ++ status = dma_cookie_status(c, cookie, state); ++ if (status == DMA_COMPLETE || !state) ++ return status; ++ ++ spin_lock_irqsave(&chan->vchan.lock, flags); ++ desc = chan->desc; ++ if (desc && (cookie == desc->vdesc.tx.cookie)) { ++ /* ++ * We never update edesc->residue in the cyclic case, so we ++ * can tell the remaining room to the end of the circular ++ * buffer. ++ */ ++ if (desc->cyclic) ++ state->residue = desc->residue - ++ ((chan->next_sg - 1) * desc->sg[0].len); ++ else ++ state->residue = desc->residue; ++ } else if ((vdesc = vchan_find_desc(&chan->vchan, cookie))) ++ state->residue = to_gdma_dma_desc(vdesc)->residue; ++ spin_unlock_irqrestore(&chan->vchan.lock, flags); ++ ++ dev_dbg(c->device->dev, "tx residue %d bytes\n", state->residue); ++ ++ return status; ++} ++ ++static void gdma_dma_free_chan_resources(struct dma_chan *c) ++{ ++ vchan_free_chan_resources(to_virt_chan(c)); ++} ++ ++static void gdma_dma_desc_free(struct virt_dma_desc *vdesc) ++{ ++ kfree(container_of(vdesc, struct gdma_dma_desc, vdesc)); ++} ++ ++static void gdma_dma_tasklet(unsigned long arg) ++{ ++ struct gdma_dma_dev *dma_dev = (struct gdma_dma_dev *)arg; ++ struct gdma_dmaengine_chan *chan; ++ static unsigned int last_chan; ++ unsigned int i, chan_mask; ++ ++ /* record last chan to round robin all chans */ ++ i = last_chan; ++ chan_mask = dma_dev->data->chancnt - 1; ++ do { ++ /* ++ * on mt7621. when verify with dmatest with all ++ * channel is enable. we need to limit only two ++ * channel is working at the same time. otherwise the ++ * data will have problem. ++ */ ++ if (atomic_read(&dma_dev->cnt) >= 2) { ++ last_chan = i; ++ break; ++ } ++ ++ if (test_and_clear_bit(i, &dma_dev->chan_issued)) { ++ chan = &dma_dev->chan[i]; ++ if (chan->desc) { ++ atomic_inc(&dma_dev->cnt); ++ gdma_start_transfer(dma_dev, chan); ++ } else ++ dev_dbg(dma_dev->ddev.dev, "chan %d no desc to issue\n", chan->id); ++ ++ if (!dma_dev->chan_issued) ++ break; ++ } ++ ++ i = (i + 1) & chan_mask; ++ } while (i != last_chan); ++} ++ ++static void rt305x_gdma_init(struct gdma_dma_dev *dma_dev) ++{ ++ uint32_t gct; ++ ++ /* all chans round robin */ ++ gdma_dma_write(dma_dev, GDMA_RT305X_GCT, GDMA_REG_GCT_ARBIT_RR); ++ ++ gct = gdma_dma_read(dma_dev, GDMA_RT305X_GCT); ++ dev_info(dma_dev->ddev.dev, "revision: %d, channels: %d\n", ++ (gct >> GDMA_REG_GCT_VER_SHIFT) & GDMA_REG_GCT_VER_MASK, ++ 8 << ((gct >> GDMA_REG_GCT_CHAN_SHIFT) & ++ GDMA_REG_GCT_CHAN_MASK)); ++} ++ ++static void rt3883_gdma_init(struct gdma_dma_dev *dma_dev) ++{ ++ uint32_t gct; ++ ++ /* all chans round robin */ ++ gdma_dma_write(dma_dev, GDMA_REG_GCT, GDMA_REG_GCT_ARBIT_RR); ++ ++ gct = gdma_dma_read(dma_dev, GDMA_REG_GCT); ++ dev_info(dma_dev->ddev.dev, "revision: %d, channels: %d\n", ++ (gct >> GDMA_REG_GCT_VER_SHIFT) & GDMA_REG_GCT_VER_MASK, ++ 8 << ((gct >> GDMA_REG_GCT_CHAN_SHIFT) & ++ GDMA_REG_GCT_CHAN_MASK)); ++} ++ ++static struct gdma_data rt305x_gdma_data = { ++ .chancnt = 8, ++ .done_int_reg = GDMA_RT305X_STATUS_INT, ++ .init = rt305x_gdma_init, ++ .start_transfer = rt305x_gdma_start_transfer, ++}; ++ ++static struct gdma_data rt3883_gdma_data = { ++ .chancnt = 16, ++ .done_int_reg = GDMA_REG_DONE_INT, ++ .init = rt3883_gdma_init, ++ .start_transfer = rt3883_gdma_start_transfer, ++}; ++ ++static const struct of_device_id gdma_of_match_table[] = { ++ { .compatible = "ralink,rt305x-gdma", .data = &rt305x_gdma_data }, ++ { .compatible = "ralink,rt3883-gdma", .data = &rt3883_gdma_data }, ++ { }, ++}; ++ ++static int gdma_dma_probe(struct platform_device *pdev) ++{ ++ const struct of_device_id *match; ++ struct gdma_dmaengine_chan *chan; ++ struct gdma_dma_dev *dma_dev; ++ struct dma_device *dd; ++ unsigned int i; ++ struct resource *res; ++ int ret; ++ int irq; ++ void __iomem *base; ++ struct gdma_data *data; ++ ++ ret = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32)); ++ if (ret) ++ return ret; ++ ++ match = of_match_device(gdma_of_match_table, &pdev->dev); ++ if (!match) ++ return -EINVAL; ++ data = (struct gdma_data *) match->data; ++ ++ dma_dev = devm_kzalloc(&pdev->dev, sizeof(*dma_dev) + ++ (sizeof(struct gdma_dmaengine_chan) * data->chancnt), ++ GFP_KERNEL); ++ if (!dma_dev) { ++ dev_err(&pdev->dev, "alloc dma device failed\n"); ++ return -EINVAL; ++ } ++ dma_dev->data = data; ++ ++ res = platform_get_resource(pdev, IORESOURCE_MEM, 0); ++ base = devm_ioremap_resource(&pdev->dev, res); ++ if (IS_ERR(base)) ++ return PTR_ERR(base); ++ dma_dev->base = base; ++ tasklet_init(&dma_dev->task, gdma_dma_tasklet, (unsigned long)dma_dev); ++ ++ irq = platform_get_irq(pdev, 0); ++ if (irq < 0) { ++ dev_err(&pdev->dev, "failed to get irq\n"); ++ return -EINVAL; ++ } ++ ret = devm_request_irq(&pdev->dev, irq, gdma_dma_irq, ++ 0, dev_name(&pdev->dev), dma_dev); ++ if (ret) { ++ dev_err(&pdev->dev, "failed to request irq\n"); ++ return ret; ++ } ++ ++ device_reset(&pdev->dev); ++ ++ dd = &dma_dev->ddev; ++ dma_cap_set(DMA_MEMCPY, dd->cap_mask); ++ dma_cap_set(DMA_SLAVE, dd->cap_mask); ++ dma_cap_set(DMA_CYCLIC, dd->cap_mask); ++ dd->device_free_chan_resources = gdma_dma_free_chan_resources; ++ dd->device_prep_dma_memcpy = gdma_dma_prep_dma_memcpy; ++ dd->device_prep_slave_sg = gdma_dma_prep_slave_sg; ++ dd->device_prep_dma_cyclic = gdma_dma_prep_dma_cyclic; ++ dd->device_config = gdma_dma_config; ++ dd->device_terminate_all = gdma_dma_terminate_all; ++ dd->device_tx_status = gdma_dma_tx_status; ++ dd->device_issue_pending = gdma_dma_issue_pending; ++ ++ dd->src_addr_widths = BIT(DMA_SLAVE_BUSWIDTH_4_BYTES); ++ dd->dst_addr_widths = BIT(DMA_SLAVE_BUSWIDTH_4_BYTES); ++ dd->directions = BIT(DMA_DEV_TO_MEM) | BIT(DMA_MEM_TO_DEV); ++ dd->residue_granularity = DMA_RESIDUE_GRANULARITY_SEGMENT; ++ ++ dd->dev = &pdev->dev; ++ dd->dev->dma_parms = &dma_dev->dma_parms; ++ dma_set_max_seg_size(dd->dev, GDMA_REG_CTRL0_TX_MASK); ++ INIT_LIST_HEAD(&dd->channels); ++ ++ for (i = 0; i < data->chancnt; i++) { ++ chan = &dma_dev->chan[i]; ++ chan->id = i; ++ chan->vchan.desc_free = gdma_dma_desc_free; ++ vchan_init(&chan->vchan, dd); ++ } ++ ++ /* init hardware */ ++ data->init(dma_dev); ++ ++ ret = dma_async_device_register(dd); ++ if (ret) { ++ dev_err(&pdev->dev, "failed to register dma device\n"); ++ return ret; ++ } ++ ++ ret = of_dma_controller_register(pdev->dev.of_node, ++ of_dma_xlate_by_chan_id, dma_dev); ++ if (ret) { ++ dev_err(&pdev->dev, "failed to register of dma controller\n"); ++ goto err_unregister; ++ } ++ ++ platform_set_drvdata(pdev, dma_dev); ++ ++ return 0; ++ ++err_unregister: ++ dma_async_device_unregister(dd); ++ return ret; ++} ++ ++static int gdma_dma_remove(struct platform_device *pdev) ++{ ++ struct gdma_dma_dev *dma_dev = platform_get_drvdata(pdev); ++ ++ tasklet_kill(&dma_dev->task); ++ of_dma_controller_free(pdev->dev.of_node); ++ dma_async_device_unregister(&dma_dev->ddev); ++ ++ return 0; ++} ++ ++static struct platform_driver gdma_dma_driver = { ++ .probe = gdma_dma_probe, ++ .remove = gdma_dma_remove, ++ .driver = { ++ .name = "gdma-rt2880", ++ .of_match_table = gdma_of_match_table, ++ }, ++}; ++module_platform_driver(gdma_dma_driver); ++ ++MODULE_AUTHOR("Lars-Peter Clausen "); ++MODULE_DESCRIPTION("Ralink/MTK DMA driver"); ++MODULE_LICENSE("GPL v2"); +--- a/include/linux/dmaengine.h ++++ b/include/linux/dmaengine.h +@@ -525,6 +525,7 @@ static inline void dma_set_unmap(struct + struct dmaengine_unmap_data * + dmaengine_get_unmap_data(struct device *dev, int nr, gfp_t flags); + void dmaengine_unmap_put(struct dmaengine_unmap_data *unmap); ++struct dma_chan *dma_get_slave_channel(struct dma_chan *chan); + #else + static inline void dma_set_unmap(struct dma_async_tx_descriptor *tx, + struct dmaengine_unmap_data *unmap) +--- /dev/null ++++ b/drivers/dma/mtk-hsdma.c +@@ -0,0 +1,767 @@ ++/* ++ * Copyright (C) 2015, Michael Lee ++ * MTK HSDMA support ++ * ++ * This program is free software; you can redistribute it and/or modify it ++ * under the terms of the GNU General Public License as published by the ++ * Free Software Foundation; either version 2 of the License, or (at your ++ * option) any later version. ++ * ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#include "virt-dma.h" ++ ++#define HSDMA_BASE_OFFSET 0x800 ++ ++#define HSDMA_REG_TX_BASE 0x00 ++#define HSDMA_REG_TX_CNT 0x04 ++#define HSDMA_REG_TX_CTX 0x08 ++#define HSDMA_REG_TX_DTX 0x0c ++#define HSDMA_REG_RX_BASE 0x100 ++#define HSDMA_REG_RX_CNT 0x104 ++#define HSDMA_REG_RX_CRX 0x108 ++#define HSDMA_REG_RX_DRX 0x10c ++#define HSDMA_REG_INFO 0x200 ++#define HSDMA_REG_GLO_CFG 0x204 ++#define HSDMA_REG_RST_CFG 0x208 ++#define HSDMA_REG_DELAY_INT 0x20c ++#define HSDMA_REG_FREEQ_THRES 0x210 ++#define HSDMA_REG_INT_STATUS 0x220 ++#define HSDMA_REG_INT_MASK 0x228 ++#define HSDMA_REG_SCH_Q01 0x280 ++#define HSDMA_REG_SCH_Q23 0x284 ++ ++#define HSDMA_DESCS_MAX 0xfff ++#define HSDMA_DESCS_NUM 8 ++#define HSDMA_DESCS_MASK (HSDMA_DESCS_NUM - 1) ++#define HSDMA_NEXT_DESC(x) (((x) + 1) & HSDMA_DESCS_MASK) ++ ++/* HSDMA_REG_INFO */ ++#define HSDMA_INFO_INDEX_MASK 0xf ++#define HSDMA_INFO_INDEX_SHIFT 24 ++#define HSDMA_INFO_BASE_MASK 0xff ++#define HSDMA_INFO_BASE_SHIFT 16 ++#define HSDMA_INFO_RX_MASK 0xff ++#define HSDMA_INFO_RX_SHIFT 8 ++#define HSDMA_INFO_TX_MASK 0xff ++#define HSDMA_INFO_TX_SHIFT 0 ++ ++/* HSDMA_REG_GLO_CFG */ ++#define HSDMA_GLO_TX_2B_OFFSET BIT(31) ++#define HSDMA_GLO_CLK_GATE BIT(30) ++#define HSDMA_GLO_BYTE_SWAP BIT(29) ++#define HSDMA_GLO_MULTI_DMA BIT(10) ++#define HSDMA_GLO_TWO_BUF BIT(9) ++#define HSDMA_GLO_32B_DESC BIT(8) ++#define HSDMA_GLO_BIG_ENDIAN BIT(7) ++#define HSDMA_GLO_TX_DONE BIT(6) ++#define HSDMA_GLO_BT_MASK 0x3 ++#define HSDMA_GLO_BT_SHIFT 4 ++#define HSDMA_GLO_RX_BUSY BIT(3) ++#define HSDMA_GLO_RX_DMA BIT(2) ++#define HSDMA_GLO_TX_BUSY BIT(1) ++#define HSDMA_GLO_TX_DMA BIT(0) ++ ++#define HSDMA_BT_SIZE_16BYTES (0 << HSDMA_GLO_BT_SHIFT) ++#define HSDMA_BT_SIZE_32BYTES (1 << HSDMA_GLO_BT_SHIFT) ++#define HSDMA_BT_SIZE_64BYTES (2 << HSDMA_GLO_BT_SHIFT) ++#define HSDMA_BT_SIZE_128BYTES (3 << HSDMA_GLO_BT_SHIFT) ++ ++#define HSDMA_GLO_DEFAULT (HSDMA_GLO_MULTI_DMA | \ ++ HSDMA_GLO_RX_DMA | HSDMA_GLO_TX_DMA | HSDMA_BT_SIZE_32BYTES) ++ ++/* HSDMA_REG_RST_CFG */ ++#define HSDMA_RST_RX_SHIFT 16 ++#define HSDMA_RST_TX_SHIFT 0 ++ ++/* HSDMA_REG_DELAY_INT */ ++#define HSDMA_DELAY_INT_EN BIT(15) ++#define HSDMA_DELAY_PEND_OFFSET 8 ++#define HSDMA_DELAY_TIME_OFFSET 0 ++#define HSDMA_DELAY_TX_OFFSET 16 ++#define HSDMA_DELAY_RX_OFFSET 0 ++ ++#define HSDMA_DELAY_INIT(x) (HSDMA_DELAY_INT_EN | \ ++ ((x) << HSDMA_DELAY_PEND_OFFSET)) ++#define HSDMA_DELAY(x) ((HSDMA_DELAY_INIT(x) << \ ++ HSDMA_DELAY_TX_OFFSET) | HSDMA_DELAY_INIT(x)) ++ ++/* HSDMA_REG_INT_STATUS */ ++#define HSDMA_INT_DELAY_RX_COH BIT(31) ++#define HSDMA_INT_DELAY_RX_INT BIT(30) ++#define HSDMA_INT_DELAY_TX_COH BIT(29) ++#define HSDMA_INT_DELAY_TX_INT BIT(28) ++#define HSDMA_INT_RX_MASK 0x3 ++#define HSDMA_INT_RX_SHIFT 16 ++#define HSDMA_INT_RX_Q0 BIT(16) ++#define HSDMA_INT_TX_MASK 0xf ++#define HSDMA_INT_TX_SHIFT 0 ++#define HSDMA_INT_TX_Q0 BIT(0) ++ ++/* tx/rx dma desc flags */ ++#define HSDMA_PLEN_MASK 0x3fff ++#define HSDMA_DESC_DONE BIT(31) ++#define HSDMA_DESC_LS0 BIT(30) ++#define HSDMA_DESC_PLEN0(_x) (((_x) & HSDMA_PLEN_MASK) << 16) ++#define HSDMA_DESC_TAG BIT(15) ++#define HSDMA_DESC_LS1 BIT(14) ++#define HSDMA_DESC_PLEN1(_x) ((_x) & HSDMA_PLEN_MASK) ++ ++/* align 4 bytes */ ++#define HSDMA_ALIGN_SIZE 3 ++/* align size 128bytes */ ++#define HSDMA_MAX_PLEN 0x3f80 ++ ++struct hsdma_desc { ++ u32 addr0; ++ u32 flags; ++ u32 addr1; ++ u32 unused; ++}; ++ ++struct mtk_hsdma_sg { ++ dma_addr_t src_addr; ++ dma_addr_t dst_addr; ++ u32 len; ++}; ++ ++struct mtk_hsdma_desc { ++ struct virt_dma_desc vdesc; ++ unsigned int num_sgs; ++ struct mtk_hsdma_sg sg[1]; ++}; ++ ++struct mtk_hsdma_chan { ++ struct virt_dma_chan vchan; ++ unsigned int id; ++ dma_addr_t desc_addr; ++ int tx_idx; ++ int rx_idx; ++ struct hsdma_desc *tx_ring; ++ struct hsdma_desc *rx_ring; ++ struct mtk_hsdma_desc *desc; ++ unsigned int next_sg; ++}; ++ ++struct mtk_hsdam_engine { ++ struct dma_device ddev; ++ struct device_dma_parameters dma_parms; ++ void __iomem *base; ++ struct tasklet_struct task; ++ volatile unsigned long chan_issued; ++ ++ struct mtk_hsdma_chan chan[1]; ++}; ++ ++static inline struct mtk_hsdam_engine *mtk_hsdma_chan_get_dev( ++ struct mtk_hsdma_chan *chan) ++{ ++ return container_of(chan->vchan.chan.device, struct mtk_hsdam_engine, ++ ddev); ++} ++ ++static inline struct mtk_hsdma_chan *to_mtk_hsdma_chan(struct dma_chan *c) ++{ ++ return container_of(c, struct mtk_hsdma_chan, vchan.chan); ++} ++ ++static inline struct mtk_hsdma_desc *to_mtk_hsdma_desc( ++ struct virt_dma_desc *vdesc) ++{ ++ return container_of(vdesc, struct mtk_hsdma_desc, vdesc); ++} ++ ++static inline u32 mtk_hsdma_read(struct mtk_hsdam_engine *hsdma, u32 reg) ++{ ++ return readl(hsdma->base + reg); ++} ++ ++static inline void mtk_hsdma_write(struct mtk_hsdam_engine *hsdma, ++ unsigned reg, u32 val) ++{ ++ writel(val, hsdma->base + reg); ++} ++ ++static void mtk_hsdma_reset_chan(struct mtk_hsdam_engine *hsdma, ++ struct mtk_hsdma_chan *chan) ++{ ++ chan->tx_idx = 0; ++ chan->rx_idx = HSDMA_DESCS_NUM - 1; ++ ++ mtk_hsdma_write(hsdma, HSDMA_REG_TX_CTX, chan->tx_idx); ++ mtk_hsdma_write(hsdma, HSDMA_REG_RX_CRX, chan->rx_idx); ++ ++ mtk_hsdma_write(hsdma, HSDMA_REG_RST_CFG, ++ 0x1 << (chan->id + HSDMA_RST_TX_SHIFT)); ++ mtk_hsdma_write(hsdma, HSDMA_REG_RST_CFG, ++ 0x1 << (chan->id + HSDMA_RST_RX_SHIFT)); ++} ++ ++static void hsdma_dump_reg(struct mtk_hsdam_engine *hsdma) ++{ ++ dev_dbg(hsdma->ddev.dev, "tbase %08x, tcnt %08x, " \ ++ "tctx %08x, tdtx: %08x, rbase %08x, " \ ++ "rcnt %08x, rctx %08x, rdtx %08x\n", ++ mtk_hsdma_read(hsdma, HSDMA_REG_TX_BASE), ++ mtk_hsdma_read(hsdma, HSDMA_REG_TX_CNT), ++ mtk_hsdma_read(hsdma, HSDMA_REG_TX_CTX), ++ mtk_hsdma_read(hsdma, HSDMA_REG_TX_DTX), ++ mtk_hsdma_read(hsdma, HSDMA_REG_RX_BASE), ++ mtk_hsdma_read(hsdma, HSDMA_REG_RX_CNT), ++ mtk_hsdma_read(hsdma, HSDMA_REG_RX_CRX), ++ mtk_hsdma_read(hsdma, HSDMA_REG_RX_DRX)); ++ ++ dev_dbg(hsdma->ddev.dev, "info %08x, glo %08x, delay %08x, " \ ++ "intr_stat %08x, intr_mask %08x\n", ++ mtk_hsdma_read(hsdma, HSDMA_REG_INFO), ++ mtk_hsdma_read(hsdma, HSDMA_REG_GLO_CFG), ++ mtk_hsdma_read(hsdma, HSDMA_REG_DELAY_INT), ++ mtk_hsdma_read(hsdma, HSDMA_REG_INT_STATUS), ++ mtk_hsdma_read(hsdma, HSDMA_REG_INT_MASK)); ++} ++ ++static void hsdma_dump_desc(struct mtk_hsdam_engine *hsdma, ++ struct mtk_hsdma_chan *chan) ++{ ++ struct hsdma_desc *tx_desc; ++ struct hsdma_desc *rx_desc; ++ int i; ++ ++ dev_dbg(hsdma->ddev.dev, "tx idx: %d, rx idx: %d\n", ++ chan->tx_idx, chan->rx_idx); ++ ++ for (i = 0; i < HSDMA_DESCS_NUM; i++) { ++ tx_desc = &chan->tx_ring[i]; ++ rx_desc = &chan->rx_ring[i]; ++ ++ dev_dbg(hsdma->ddev.dev, "%d tx addr0: %08x, flags %08x, " \ ++ "tx addr1: %08x, rx addr0 %08x, flags %08x\n", ++ i, tx_desc->addr0, tx_desc->flags, \ ++ tx_desc->addr1, rx_desc->addr0, rx_desc->flags); ++ } ++} ++ ++static void mtk_hsdma_reset(struct mtk_hsdam_engine *hsdma, ++ struct mtk_hsdma_chan *chan) ++{ ++ int i; ++ ++ /* disable dma */ ++ mtk_hsdma_write(hsdma, HSDMA_REG_GLO_CFG, 0); ++ ++ /* disable intr */ ++ mtk_hsdma_write(hsdma, HSDMA_REG_INT_MASK, 0); ++ ++ /* init desc value */ ++ for (i = 0; i < HSDMA_DESCS_NUM; i++) { ++ chan->tx_ring[i].addr0 = 0; ++ chan->tx_ring[i].flags = HSDMA_DESC_LS0 | ++ HSDMA_DESC_DONE; ++ } ++ for (i = 0; i < HSDMA_DESCS_NUM; i++) { ++ chan->rx_ring[i].addr0 = 0; ++ chan->rx_ring[i].flags = 0; ++ } ++ ++ /* reset */ ++ mtk_hsdma_reset_chan(hsdma, chan); ++ ++ /* enable intr */ ++ mtk_hsdma_write(hsdma, HSDMA_REG_INT_MASK, HSDMA_INT_RX_Q0); ++ ++ /* enable dma */ ++ mtk_hsdma_write(hsdma, HSDMA_REG_GLO_CFG, HSDMA_GLO_DEFAULT); ++} ++ ++static int mtk_hsdma_terminate_all(struct dma_chan *c) ++{ ++ struct mtk_hsdma_chan *chan = to_mtk_hsdma_chan(c); ++ struct mtk_hsdam_engine *hsdma = mtk_hsdma_chan_get_dev(chan); ++ unsigned long timeout; ++ LIST_HEAD(head); ++ ++ spin_lock_bh(&chan->vchan.lock); ++ chan->desc = NULL; ++ clear_bit(chan->id, &hsdma->chan_issued); ++ vchan_get_all_descriptors(&chan->vchan, &head); ++ spin_unlock_bh(&chan->vchan.lock); ++ ++ vchan_dma_desc_free_list(&chan->vchan, &head); ++ ++ /* wait dma transfer complete */ ++ timeout = jiffies + msecs_to_jiffies(2000); ++ while (mtk_hsdma_read(hsdma, HSDMA_REG_GLO_CFG) & ++ (HSDMA_GLO_RX_BUSY | HSDMA_GLO_TX_BUSY)) { ++ if (time_after_eq(jiffies, timeout)) { ++ hsdma_dump_desc(hsdma, chan); ++ mtk_hsdma_reset(hsdma, chan); ++ dev_err(hsdma->ddev.dev, "timeout, reset it\n"); ++ break; ++ } ++ cpu_relax(); ++ } ++ ++ return 0; ++} ++ ++static int mtk_hsdma_start_transfer(struct mtk_hsdam_engine *hsdma, ++ struct mtk_hsdma_chan *chan) ++{ ++ dma_addr_t src, dst; ++ size_t len, tlen; ++ struct hsdma_desc *tx_desc, *rx_desc; ++ struct mtk_hsdma_sg *sg; ++ unsigned int i; ++ int rx_idx; ++ ++ sg = &chan->desc->sg[0]; ++ len = sg->len; ++ chan->desc->num_sgs = DIV_ROUND_UP(len, HSDMA_MAX_PLEN); ++ ++ /* tx desc */ ++ src = sg->src_addr; ++ for (i = 0; i < chan->desc->num_sgs; i++) { ++ if (len > HSDMA_MAX_PLEN) ++ tlen = HSDMA_MAX_PLEN; ++ else ++ tlen = len; ++ ++ if (i & 0x1) { ++ tx_desc->addr1 = src; ++ tx_desc->flags |= HSDMA_DESC_PLEN1(tlen); ++ } else { ++ tx_desc = &chan->tx_ring[chan->tx_idx]; ++ tx_desc->addr0 = src; ++ tx_desc->flags = HSDMA_DESC_PLEN0(tlen); ++ ++ /* update index */ ++ chan->tx_idx = HSDMA_NEXT_DESC(chan->tx_idx); ++ } ++ ++ src += tlen; ++ len -= tlen; ++ } ++ if (i & 0x1) ++ tx_desc->flags |= HSDMA_DESC_LS0; ++ else ++ tx_desc->flags |= HSDMA_DESC_LS1; ++ ++ /* rx desc */ ++ rx_idx = HSDMA_NEXT_DESC(chan->rx_idx); ++ len = sg->len; ++ dst = sg->dst_addr; ++ for (i = 0; i < chan->desc->num_sgs; i++) { ++ rx_desc = &chan->rx_ring[rx_idx]; ++ if (len > HSDMA_MAX_PLEN) ++ tlen = HSDMA_MAX_PLEN; ++ else ++ tlen = len; ++ ++ rx_desc->addr0 = dst; ++ rx_desc->flags = HSDMA_DESC_PLEN0(tlen); ++ ++ dst += tlen; ++ len -= tlen; ++ ++ /* update index */ ++ rx_idx = HSDMA_NEXT_DESC(rx_idx); ++ } ++ ++ /* make sure desc and index all up to date */ ++ wmb(); ++ mtk_hsdma_write(hsdma, HSDMA_REG_TX_CTX, chan->tx_idx); ++ ++ return 0; ++} ++ ++static int gdma_next_desc(struct mtk_hsdma_chan *chan) ++{ ++ struct virt_dma_desc *vdesc; ++ ++ vdesc = vchan_next_desc(&chan->vchan); ++ if (!vdesc) { ++ chan->desc = NULL; ++ return 0; ++ } ++ chan->desc = to_mtk_hsdma_desc(vdesc); ++ chan->next_sg = 0; ++ ++ return 1; ++} ++ ++static void mtk_hsdma_chan_done(struct mtk_hsdam_engine *hsdma, ++ struct mtk_hsdma_chan *chan) ++{ ++ struct mtk_hsdma_desc *desc; ++ int chan_issued; ++ ++ chan_issued = 0; ++ spin_lock_bh(&chan->vchan.lock); ++ desc = chan->desc; ++ if (likely(desc)) { ++ if (chan->next_sg == desc->num_sgs) { ++ list_del(&desc->vdesc.node); ++ vchan_cookie_complete(&desc->vdesc); ++ chan_issued = gdma_next_desc(chan); ++ } ++ } else ++ dev_dbg(hsdma->ddev.dev, "no desc to complete\n"); ++ ++ if (chan_issued) ++ set_bit(chan->id, &hsdma->chan_issued); ++ spin_unlock_bh(&chan->vchan.lock); ++} ++ ++static irqreturn_t mtk_hsdma_irq(int irq, void *devid) ++{ ++ struct mtk_hsdam_engine *hsdma = devid; ++ u32 status; ++ ++ status = mtk_hsdma_read(hsdma, HSDMA_REG_INT_STATUS); ++ if (unlikely(!status)) ++ return IRQ_NONE; ++ ++ if (likely(status & HSDMA_INT_RX_Q0)) ++ tasklet_schedule(&hsdma->task); ++ else ++ dev_dbg(hsdma->ddev.dev, "unhandle irq status %08x\n", ++ status); ++ /* clean intr bits */ ++ mtk_hsdma_write(hsdma, HSDMA_REG_INT_STATUS, status); ++ ++ return IRQ_HANDLED; ++} ++ ++static void mtk_hsdma_issue_pending(struct dma_chan *c) ++{ ++ struct mtk_hsdma_chan *chan = to_mtk_hsdma_chan(c); ++ struct mtk_hsdam_engine *hsdma = mtk_hsdma_chan_get_dev(chan); ++ ++ spin_lock_bh(&chan->vchan.lock); ++ if (vchan_issue_pending(&chan->vchan) && !chan->desc) { ++ if (gdma_next_desc(chan)) { ++ set_bit(chan->id, &hsdma->chan_issued); ++ tasklet_schedule(&hsdma->task); ++ } else ++ dev_dbg(hsdma->ddev.dev, "no desc to issue\n"); ++ } ++ spin_unlock_bh(&chan->vchan.lock); ++} ++ ++static struct dma_async_tx_descriptor * mtk_hsdma_prep_dma_memcpy( ++ struct dma_chan *c, dma_addr_t dest, dma_addr_t src, ++ size_t len, unsigned long flags) ++{ ++ struct mtk_hsdma_chan *chan = to_mtk_hsdma_chan(c); ++ struct mtk_hsdma_desc *desc; ++ ++ if (len <= 0) ++ return NULL; ++ ++ desc = kzalloc(sizeof(struct mtk_hsdma_desc), GFP_ATOMIC); ++ if (!desc) { ++ dev_err(c->device->dev, "alloc memcpy decs error\n"); ++ return NULL; ++ } ++ ++ desc->sg[0].src_addr = src; ++ desc->sg[0].dst_addr = dest; ++ desc->sg[0].len = len; ++ ++ return vchan_tx_prep(&chan->vchan, &desc->vdesc, flags); ++} ++ ++static enum dma_status mtk_hsdma_tx_status(struct dma_chan *c, ++ dma_cookie_t cookie, struct dma_tx_state *state) ++{ ++ return dma_cookie_status(c, cookie, state); ++} ++ ++static void mtk_hsdma_free_chan_resources(struct dma_chan *c) ++{ ++ vchan_free_chan_resources(to_virt_chan(c)); ++} ++ ++static void mtk_hsdma_desc_free(struct virt_dma_desc *vdesc) ++{ ++ kfree(container_of(vdesc, struct mtk_hsdma_desc, vdesc)); ++} ++ ++static void mtk_hsdma_tx(struct mtk_hsdam_engine *hsdma) ++{ ++ struct mtk_hsdma_chan *chan; ++ ++ if (test_and_clear_bit(0, &hsdma->chan_issued)) { ++ chan = &hsdma->chan[0]; ++ if (chan->desc) { ++ mtk_hsdma_start_transfer(hsdma, chan); ++ } else ++ dev_dbg(hsdma->ddev.dev,"chan 0 no desc to issue\n"); ++ } ++} ++ ++static void mtk_hsdma_rx(struct mtk_hsdam_engine *hsdma) ++{ ++ struct mtk_hsdma_chan *chan; ++ int next_idx, drx_idx, cnt; ++ ++ chan = &hsdma->chan[0]; ++ next_idx = HSDMA_NEXT_DESC(chan->rx_idx); ++ drx_idx = mtk_hsdma_read(hsdma, HSDMA_REG_RX_DRX); ++ ++ cnt = (drx_idx - next_idx) & HSDMA_DESCS_MASK; ++ if (!cnt) ++ return; ++ ++ chan->next_sg += cnt; ++ chan->rx_idx = (chan->rx_idx + cnt) & HSDMA_DESCS_MASK; ++ ++ /* update rx crx */ ++ wmb(); ++ mtk_hsdma_write(hsdma, HSDMA_REG_RX_CRX, chan->rx_idx); ++ ++ mtk_hsdma_chan_done(hsdma, chan); ++} ++ ++static void mtk_hsdma_tasklet(unsigned long arg) ++{ ++ struct mtk_hsdam_engine *hsdma = (struct mtk_hsdam_engine *)arg; ++ ++ mtk_hsdma_rx(hsdma); ++ mtk_hsdma_tx(hsdma); ++} ++ ++static int mtk_hsdam_alloc_desc(struct mtk_hsdam_engine *hsdma, ++ struct mtk_hsdma_chan *chan) ++{ ++ int i; ++ ++ chan->tx_ring = dma_alloc_coherent(hsdma->ddev.dev, ++ 2 * HSDMA_DESCS_NUM * sizeof(*chan->tx_ring), ++ &chan->desc_addr, GFP_ATOMIC | __GFP_ZERO); ++ if (!chan->tx_ring) ++ goto no_mem; ++ ++ chan->rx_ring = &chan->tx_ring[HSDMA_DESCS_NUM]; ++ ++ /* init tx ring value */ ++ for (i = 0; i < HSDMA_DESCS_NUM; i++) ++ chan->tx_ring[i].flags = HSDMA_DESC_LS0 | HSDMA_DESC_DONE; ++ ++ return 0; ++no_mem: ++ return -ENOMEM; ++} ++ ++static void mtk_hsdam_free_desc(struct mtk_hsdam_engine *hsdma, ++ struct mtk_hsdma_chan *chan) ++{ ++ if (chan->tx_ring) { ++ dma_free_coherent(hsdma->ddev.dev, ++ 2 * HSDMA_DESCS_NUM * sizeof(*chan->tx_ring), ++ chan->tx_ring, chan->desc_addr); ++ chan->tx_ring = NULL; ++ chan->rx_ring = NULL; ++ } ++} ++ ++static int mtk_hsdma_init(struct mtk_hsdam_engine *hsdma) ++{ ++ struct mtk_hsdma_chan *chan; ++ int ret; ++ u32 reg; ++ ++ /* init desc */ ++ chan = &hsdma->chan[0]; ++ ret = mtk_hsdam_alloc_desc(hsdma, chan); ++ if (ret) ++ return ret; ++ ++ /* tx */ ++ mtk_hsdma_write(hsdma, HSDMA_REG_TX_BASE, chan->desc_addr); ++ mtk_hsdma_write(hsdma, HSDMA_REG_TX_CNT, HSDMA_DESCS_NUM); ++ /* rx */ ++ mtk_hsdma_write(hsdma, HSDMA_REG_RX_BASE, chan->desc_addr + ++ (sizeof(struct hsdma_desc) * HSDMA_DESCS_NUM)); ++ mtk_hsdma_write(hsdma, HSDMA_REG_RX_CNT, HSDMA_DESCS_NUM); ++ /* reset */ ++ mtk_hsdma_reset_chan(hsdma, chan); ++ ++ /* enable rx intr */ ++ mtk_hsdma_write(hsdma, HSDMA_REG_INT_MASK, HSDMA_INT_RX_Q0); ++ ++ /* enable dma */ ++ mtk_hsdma_write(hsdma, HSDMA_REG_GLO_CFG, HSDMA_GLO_DEFAULT); ++ ++ /* hardware info */ ++ reg = mtk_hsdma_read(hsdma, HSDMA_REG_INFO); ++ dev_info(hsdma->ddev.dev, "rx: %d, tx: %d\n", ++ (reg >> HSDMA_INFO_RX_SHIFT) & HSDMA_INFO_RX_MASK, ++ (reg >> HSDMA_INFO_TX_SHIFT) & HSDMA_INFO_TX_MASK); ++ ++ hsdma_dump_reg(hsdma); ++ ++ return ret; ++} ++ ++static void mtk_hsdma_uninit(struct mtk_hsdam_engine *hsdma) ++{ ++ struct mtk_hsdma_chan *chan; ++ ++ /* disable dma */ ++ mtk_hsdma_write(hsdma, HSDMA_REG_GLO_CFG, 0); ++ ++ /* disable intr */ ++ mtk_hsdma_write(hsdma, HSDMA_REG_INT_MASK, 0); ++ ++ /* free desc */ ++ chan = &hsdma->chan[0]; ++ mtk_hsdam_free_desc(hsdma, chan); ++ ++ /* tx */ ++ mtk_hsdma_write(hsdma, HSDMA_REG_TX_BASE, 0); ++ mtk_hsdma_write(hsdma, HSDMA_REG_TX_CNT, 0); ++ /* rx */ ++ mtk_hsdma_write(hsdma, HSDMA_REG_RX_BASE, 0); ++ mtk_hsdma_write(hsdma, HSDMA_REG_RX_CNT, 0); ++ /* reset */ ++ mtk_hsdma_reset_chan(hsdma, chan); ++} ++ ++static const struct of_device_id mtk_hsdma_of_match[] = { ++ { .compatible = "mediatek,mt7621-hsdma" }, ++ { }, ++}; ++ ++static int mtk_hsdma_probe(struct platform_device *pdev) ++{ ++ const struct of_device_id *match; ++ struct mtk_hsdma_chan *chan; ++ struct mtk_hsdam_engine *hsdma; ++ struct dma_device *dd; ++ struct resource *res; ++ int ret; ++ int irq; ++ void __iomem *base; ++ ++ ret = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32)); ++ if (ret) ++ return ret; ++ ++ match = of_match_device(mtk_hsdma_of_match, &pdev->dev); ++ if (!match) ++ return -EINVAL; ++ ++ hsdma = devm_kzalloc(&pdev->dev, sizeof(*hsdma), GFP_KERNEL); ++ if (!hsdma) { ++ dev_err(&pdev->dev, "alloc dma device failed\n"); ++ return -EINVAL; ++ } ++ ++ res = platform_get_resource(pdev, IORESOURCE_MEM, 0); ++ base = devm_ioremap_resource(&pdev->dev, res); ++ if (IS_ERR(base)) ++ return PTR_ERR(base); ++ hsdma->base = base + HSDMA_BASE_OFFSET; ++ tasklet_init(&hsdma->task, mtk_hsdma_tasklet, (unsigned long)hsdma); ++ ++ irq = platform_get_irq(pdev, 0); ++ if (irq < 0) { ++ dev_err(&pdev->dev, "failed to get irq\n"); ++ return -EINVAL; ++ } ++ ret = devm_request_irq(&pdev->dev, irq, mtk_hsdma_irq, ++ 0, dev_name(&pdev->dev), hsdma); ++ if (ret) { ++ dev_err(&pdev->dev, "failed to request irq\n"); ++ return ret; ++ } ++ ++ device_reset(&pdev->dev); ++ ++ dd = &hsdma->ddev; ++ dma_cap_set(DMA_MEMCPY, dd->cap_mask); ++ dd->copy_align = HSDMA_ALIGN_SIZE; ++ dd->device_free_chan_resources = mtk_hsdma_free_chan_resources; ++ dd->device_prep_dma_memcpy = mtk_hsdma_prep_dma_memcpy; ++ dd->device_terminate_all = mtk_hsdma_terminate_all; ++ dd->device_tx_status = mtk_hsdma_tx_status; ++ dd->device_issue_pending = mtk_hsdma_issue_pending; ++ dd->dev = &pdev->dev; ++ dd->dev->dma_parms = &hsdma->dma_parms; ++ dma_set_max_seg_size(dd->dev, HSDMA_MAX_PLEN); ++ INIT_LIST_HEAD(&dd->channels); ++ ++ chan = &hsdma->chan[0]; ++ chan->id = 0; ++ chan->vchan.desc_free = mtk_hsdma_desc_free; ++ vchan_init(&chan->vchan, dd); ++ ++ /* init hardware */ ++ ret = mtk_hsdma_init(hsdma); ++ if (ret) { ++ dev_err(&pdev->dev, "failed to alloc ring descs\n"); ++ return ret; ++ } ++ ++ ret = dma_async_device_register(dd); ++ if (ret) { ++ dev_err(&pdev->dev, "failed to register dma device\n"); ++ return ret; ++ } ++ ++ ret = of_dma_controller_register(pdev->dev.of_node, ++ of_dma_xlate_by_chan_id, hsdma); ++ if (ret) { ++ dev_err(&pdev->dev, "failed to register of dma controller\n"); ++ goto err_unregister; ++ } ++ ++ platform_set_drvdata(pdev, hsdma); ++ ++ return 0; ++ ++err_unregister: ++ dma_async_device_unregister(dd); ++ return ret; ++} ++ ++static int mtk_hsdma_remove(struct platform_device *pdev) ++{ ++ struct mtk_hsdam_engine *hsdma = platform_get_drvdata(pdev); ++ ++ mtk_hsdma_uninit(hsdma); ++ ++ of_dma_controller_free(pdev->dev.of_node); ++ dma_async_device_unregister(&hsdma->ddev); ++ ++ return 0; ++} ++ ++static struct platform_driver mtk_hsdma_driver = { ++ .probe = mtk_hsdma_probe, ++ .remove = mtk_hsdma_remove, ++ .driver = { ++ .name = "hsdma-mt7621", ++ .of_match_table = mtk_hsdma_of_match, ++ }, ++}; ++module_platform_driver(mtk_hsdma_driver); ++ ++MODULE_AUTHOR("Michael Lee "); ++MODULE_DESCRIPTION("MTK HSDMA driver"); ++MODULE_LICENSE("GPL v2"); diff --git a/target/linux/ramips/patches-5.4/0048-asoc-add-mt7620-support.patch b/target/linux/ramips/patches-5.4/0048-asoc-add-mt7620-support.patch new file mode 100644 index 0000000000..1834e88538 --- /dev/null +++ b/target/linux/ramips/patches-5.4/0048-asoc-add-mt7620-support.patch @@ -0,0 +1,1046 @@ +From 7f29222b1731e8182ba94a331531dec18865a1e4 Mon Sep 17 00:00:00 2001 +From: John Crispin +Date: Sun, 27 Jul 2014 09:31:47 +0100 +Subject: [PATCH 48/53] asoc: add mt7620 support + +Signed-off-by: John Crispin +--- + arch/mips/ralink/of.c | 2 + + sound/soc/Kconfig | 1 + + sound/soc/Makefile | 1 + + sound/soc/ralink/Kconfig | 15 ++ + sound/soc/ralink/Makefile | 11 + + sound/soc/ralink/mt7620-i2s.c | 436 ++++++++++++++++++++++++++++++++++++++ + sound/soc/ralink/mt7620-wm8960.c | 233 ++++++++++++++++++++ + 7 files changed, 699 insertions(+) + create mode 100644 sound/soc/ralink/Kconfig + create mode 100644 sound/soc/ralink/Makefile + create mode 100644 sound/soc/ralink/mt7620-i2s.c + create mode 100644 sound/soc/ralink/mt7620-wm8960.c + +--- a/arch/mips/ralink/of.c ++++ b/arch/mips/ralink/of.c +@@ -15,6 +15,7 @@ + #include + #include + #include ++#include + #include + #include + +@@ -26,6 +27,7 @@ + #include "common.h" + + __iomem void *rt_sysc_membase; ++EXPORT_SYMBOL(rt_sysc_membase); + __iomem void *rt_memc_membase; + + __iomem void *plat_of_remap_node(const char *node) +--- a/sound/soc/Kconfig ++++ b/sound/soc/Kconfig +@@ -59,6 +59,7 @@ source "sound/soc/mxs/Kconfig" + source "sound/soc/pxa/Kconfig" + source "sound/soc/qcom/Kconfig" + source "sound/soc/rockchip/Kconfig" ++source "sound/soc/ralink/Kconfig" + source "sound/soc/samsung/Kconfig" + source "sound/soc/sh/Kconfig" + source "sound/soc/sirf/Kconfig" +--- a/sound/soc/Makefile ++++ b/sound/soc/Makefile +@@ -40,6 +40,7 @@ obj-$(CONFIG_SND_SOC) += kirkwood/ + obj-$(CONFIG_SND_SOC) += pxa/ + obj-$(CONFIG_SND_SOC) += qcom/ + obj-$(CONFIG_SND_SOC) += rockchip/ ++obj-$(CONFIG_SND_SOC) += ralink/ + obj-$(CONFIG_SND_SOC) += samsung/ + obj-$(CONFIG_SND_SOC) += sh/ + obj-$(CONFIG_SND_SOC) += sirf/ +--- /dev/null ++++ b/sound/soc/ralink/Kconfig +@@ -0,0 +1,8 @@ ++config SND_RALINK_SOC_I2S ++ depends on RALINK && SND_SOC && !SOC_RT288X ++ select SND_SOC_GENERIC_DMAENGINE_PCM ++ select REGMAP_MMIO ++ tristate "SoC Audio (I2S protocol) for Ralink SoC" ++ help ++ Say Y if you want to use I2S protocol and I2S codec on Ralink/MediaTek ++ based boards. +--- /dev/null ++++ b/sound/soc/ralink/Makefile +@@ -0,0 +1,6 @@ ++# ++# Ralink/MediaTek Platform Support ++# ++snd-soc-ralink-i2s-objs := ralink-i2s.o ++ ++obj-$(CONFIG_SND_RALINK_SOC_I2S) += snd-soc-ralink-i2s.o +--- /dev/null ++++ b/sound/soc/ralink/ralink-i2s.c +@@ -0,0 +1,965 @@ ++/* ++ * Copyright (C) 2010, Lars-Peter Clausen ++ * Copyright (C) 2016 Michael Lee ++ * ++ * This program is free software; you can redistribute it and/or modify it ++ * under the terms of the GNU General Public License as published by the ++ * Free Software Foundation; either version 2 of the License, or (at your ++ * option) any later version. ++ * ++ * You should have received a copy of the GNU General Public License along ++ * with this program; if not, write to the Free Software Foundation, Inc., ++ * 675 Mass Ave, Cambridge, MA 02139, USA. ++ * ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#include ++ ++#define DRV_NAME "ralink-i2s" ++ ++#define I2S_REG_CFG0 0x00 ++#define I2S_REG_INT_STATUS 0x04 ++#define I2S_REG_INT_EN 0x08 ++#define I2S_REG_FF_STATUS 0x0c ++#define I2S_REG_WREG 0x10 ++#define I2S_REG_RREG 0x14 ++#define I2S_REG_CFG1 0x18 ++#define I2S_REG_DIVCMP 0x20 ++#define I2S_REG_DIVINT 0x24 ++ ++/* I2S_REG_CFG0 */ ++#define I2S_REG_CFG0_EN BIT(31) ++#define I2S_REG_CFG0_DMA_EN BIT(30) ++#define I2S_REG_CFG0_BYTE_SWAP BIT(28) ++#define I2S_REG_CFG0_TX_EN BIT(24) ++#define I2S_REG_CFG0_RX_EN BIT(20) ++#define I2S_REG_CFG0_SLAVE BIT(16) ++#define I2S_REG_CFG0_RX_THRES 12 ++#define I2S_REG_CFG0_TX_THRES 4 ++#define I2S_REG_CFG0_THRES_MASK (0xf << I2S_REG_CFG0_RX_THRES) | \ ++ (4 << I2S_REG_CFG0_TX_THRES) ++#define I2S_REG_CFG0_DFT_THRES (4 << I2S_REG_CFG0_RX_THRES) | \ ++ (4 << I2S_REG_CFG0_TX_THRES) ++/* RT305x */ ++#define I2S_REG_CFG0_CLK_DIS BIT(8) ++#define I2S_REG_CFG0_TXCH_SWAP BIT(3) ++#define I2S_REG_CFG0_TXCH1_OFF BIT(2) ++#define I2S_REG_CFG0_TXCH0_OFF BIT(1) ++#define I2S_REG_CFG0_SLAVE_EN BIT(0) ++/* RT3883 */ ++#define I2S_REG_CFG0_RXCH_SWAP BIT(11) ++#define I2S_REG_CFG0_RXCH1_OFF BIT(10) ++#define I2S_REG_CFG0_RXCH0_OFF BIT(9) ++#define I2S_REG_CFG0_WS_INV BIT(0) ++/* MT7628 */ ++#define I2S_REG_CFG0_FMT_LE BIT(29) ++#define I2S_REG_CFG0_SYS_BE BIT(28) ++#define I2S_REG_CFG0_NORM_24 BIT(18) ++#define I2S_REG_CFG0_DATA_24 BIT(17) ++ ++/* I2S_REG_INT_STATUS */ ++#define I2S_REG_INT_RX_FAULT BIT(7) ++#define I2S_REG_INT_RX_OVRUN BIT(6) ++#define I2S_REG_INT_RX_UNRUN BIT(5) ++#define I2S_REG_INT_RX_THRES BIT(4) ++#define I2S_REG_INT_TX_FAULT BIT(3) ++#define I2S_REG_INT_TX_OVRUN BIT(2) ++#define I2S_REG_INT_TX_UNRUN BIT(1) ++#define I2S_REG_INT_TX_THRES BIT(0) ++#define I2S_REG_INT_TX_MASK 0xf ++#define I2S_REG_INT_RX_MASK 0xf0 ++ ++/* I2S_REG_INT_STATUS */ ++#define I2S_RX_AVCNT(x) ((x >> 4) & 0xf) ++#define I2S_TX_AVCNT(x) (x & 0xf) ++/* MT7628 */ ++#define MT7628_I2S_RX_AVCNT(x) ((x >> 8) & 0x1f) ++#define MT7628_I2S_TX_AVCNT(x) (x & 0x1f) ++ ++/* I2S_REG_CFG1 */ ++#define I2S_REG_CFG1_LBK BIT(31) ++#define I2S_REG_CFG1_EXTLBK BIT(30) ++/* RT3883 */ ++#define I2S_REG_CFG1_LEFT_J BIT(0) ++#define I2S_REG_CFG1_RIGHT_J BIT(1) ++#define I2S_REG_CFG1_FMT_MASK 0x3 ++ ++/* I2S_REG_DIVCMP */ ++#define I2S_REG_DIVCMP_CLKEN BIT(31) ++#define I2S_REG_DIVCMP_DIVCOMP_MASK 0x1ff ++ ++/* I2S_REG_DIVINT */ ++#define I2S_REG_DIVINT_MASK 0x3ff ++ ++/* BCLK dividers */ ++#define RALINK_I2S_DIVCMP 0 ++#define RALINK_I2S_DIVINT 1 ++ ++/* FIFO */ ++#define RALINK_I2S_FIFO_SIZE 32 ++ ++/* feature flags */ ++#define RALINK_FLAGS_TXONLY BIT(0) ++#define RALINK_FLAGS_LEFT_J BIT(1) ++#define RALINK_FLAGS_RIGHT_J BIT(2) ++#define RALINK_FLAGS_ENDIAN BIT(3) ++#define RALINK_FLAGS_24BIT BIT(4) ++ ++#define RALINK_I2S_INT_EN 0 ++ ++struct ralink_i2s_stats { ++ u32 dmafault; ++ u32 overrun; ++ u32 underrun; ++ u32 belowthres; ++}; ++ ++struct ralink_i2s { ++ struct device *dev; ++ void __iomem *regs; ++ struct clk *clk; ++ struct regmap *regmap; ++ u32 flags; ++ unsigned int fmt; ++ u16 txdma_req; ++ u16 rxdma_req; ++ ++ struct snd_dmaengine_dai_dma_data playback_dma_data; ++ struct snd_dmaengine_dai_dma_data capture_dma_data; ++ ++ struct dentry *dbg_dir; ++ struct dentry *dbg_stats; ++ struct ralink_i2s_stats txstats; ++ struct ralink_i2s_stats rxstats; ++}; ++ ++static void ralink_i2s_dump_regs(struct ralink_i2s *i2s) ++{ ++ u32 buf[10]; ++ int ret; ++ ++ ret = regmap_bulk_read(i2s->regmap, I2S_REG_CFG0, ++ buf, ARRAY_SIZE(buf)); ++ ++ dev_dbg(i2s->dev, "CFG0: %08x, INTSTAT: %08x, INTEN: %08x, " \ ++ "FFSTAT: %08x, WREG: %08x, RREG: %08x, " \ ++ "CFG1: %08x, DIVCMP: %08x, DIVINT: %08x\n", ++ buf[0], buf[1], buf[2], buf[3], buf[4], ++ buf[5], buf[6], buf[8], buf[9]); ++} ++ ++static int ralink_i2s_set_sysclk(struct snd_soc_dai *dai, ++ int clk_id, unsigned int freq, int dir) ++{ ++ return 0; ++} ++ ++static int ralink_i2s_set_sys_bclk(struct snd_soc_dai *dai, int width, int rate) ++{ ++ struct ralink_i2s *i2s = snd_soc_dai_get_drvdata(dai); ++ unsigned long clk = clk_get_rate(i2s->clk); ++ int div; ++ uint32_t data; ++ ++ /* disable clock at slave mode */ ++ if ((i2s->fmt & SND_SOC_DAIFMT_MASTER_MASK) == ++ SND_SOC_DAIFMT_CBM_CFM) { ++ regmap_update_bits(i2s->regmap, I2S_REG_CFG0, ++ I2S_REG_CFG0_CLK_DIS, ++ I2S_REG_CFG0_CLK_DIS); ++ return 0; ++ } ++ ++ /* FREQOUT = FREQIN / (I2S_CLK_DIV + 1) */ ++ div = (clk / rate ) - 1; ++ ++ data = rt_sysc_r32(0x30); ++ data &= (0xff << 8); ++ data |= (0x1 << 15) | (div << 8); ++ rt_sysc_w32(data, 0x30); ++ ++ /* enable clock */ ++ regmap_update_bits(i2s->regmap, I2S_REG_CFG0, I2S_REG_CFG0_CLK_DIS, 0); ++ ++ dev_dbg(i2s->dev, "clk: %lu, rate: %u, div: %d\n", ++ clk, rate, div); ++ ++ return 0; ++} ++ ++static int ralink_i2s_set_bclk(struct snd_soc_dai *dai, int width, int rate) ++{ ++ struct ralink_i2s *i2s = snd_soc_dai_get_drvdata(dai); ++ unsigned long clk = clk_get_rate(i2s->clk); ++ int divint, divcomp; ++ ++ /* disable clock at slave mode */ ++ if ((i2s->fmt & SND_SOC_DAIFMT_MASTER_MASK) == ++ SND_SOC_DAIFMT_CBM_CFM) { ++ regmap_update_bits(i2s->regmap, I2S_REG_DIVCMP, ++ I2S_REG_DIVCMP_CLKEN, 0); ++ return 0; ++ } ++ ++ /* FREQOUT = FREQIN * (1/2) * (1/(DIVINT + DIVCOMP/512)) */ ++ clk = clk / (2 * 2 * width); ++ divint = clk / rate; ++ divcomp = ((clk % rate) * 512) / rate; ++ ++ if ((divint > I2S_REG_DIVINT_MASK) || ++ (divcomp > I2S_REG_DIVCMP_DIVCOMP_MASK)) ++ return -EINVAL; ++ ++ regmap_update_bits(i2s->regmap, I2S_REG_DIVINT, ++ I2S_REG_DIVINT_MASK, divint); ++ regmap_update_bits(i2s->regmap, I2S_REG_DIVCMP, ++ I2S_REG_DIVCMP_DIVCOMP_MASK, divcomp); ++ ++ /* enable clock */ ++ regmap_update_bits(i2s->regmap, I2S_REG_DIVCMP, I2S_REG_DIVCMP_CLKEN, ++ I2S_REG_DIVCMP_CLKEN); ++ ++ dev_dbg(i2s->dev, "clk: %lu, rate: %u, int: %d, comp: %d\n", ++ clk_get_rate(i2s->clk), rate, divint, divcomp); ++ ++ return 0; ++} ++ ++static int ralink_i2s_set_fmt(struct snd_soc_dai *dai, unsigned int fmt) ++{ ++ struct ralink_i2s *i2s = snd_soc_dai_get_drvdata(dai); ++ unsigned int cfg0 = 0, cfg1 = 0; ++ ++ /* set master/slave audio interface */ ++ switch (fmt & SND_SOC_DAIFMT_MASTER_MASK) { ++ case SND_SOC_DAIFMT_CBM_CFM: ++ if (i2s->flags & RALINK_FLAGS_TXONLY) ++ cfg0 |= I2S_REG_CFG0_SLAVE_EN; ++ else ++ cfg0 |= I2S_REG_CFG0_SLAVE; ++ break; ++ case SND_SOC_DAIFMT_CBS_CFS: ++ break; ++ default: ++ return -EINVAL; ++ } ++ ++ /* interface format */ ++ switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) { ++ case SND_SOC_DAIFMT_I2S: ++ break; ++ case SND_SOC_DAIFMT_RIGHT_J: ++ if (i2s->flags & RALINK_FLAGS_RIGHT_J) { ++ cfg1 |= I2S_REG_CFG1_RIGHT_J; ++ break; ++ } ++ return -EINVAL; ++ case SND_SOC_DAIFMT_LEFT_J: ++ if (i2s->flags & RALINK_FLAGS_LEFT_J) { ++ cfg1 |= I2S_REG_CFG1_LEFT_J; ++ break; ++ } ++ return -EINVAL; ++ default: ++ return -EINVAL; ++ } ++ ++ /* clock inversion */ ++ switch (fmt & SND_SOC_DAIFMT_INV_MASK) { ++ case SND_SOC_DAIFMT_NB_NF: ++ break; ++ default: ++ return -EINVAL; ++ } ++ ++ if (i2s->flags & RALINK_FLAGS_TXONLY) { ++ regmap_update_bits(i2s->regmap, I2S_REG_CFG0, ++ I2S_REG_CFG0_SLAVE_EN, cfg0); ++ } else { ++ regmap_update_bits(i2s->regmap, I2S_REG_CFG0, ++ I2S_REG_CFG0_SLAVE, cfg0); ++ } ++ regmap_update_bits(i2s->regmap, I2S_REG_CFG1, ++ I2S_REG_CFG1_FMT_MASK, cfg1); ++ i2s->fmt = fmt; ++ ++ return 0; ++} ++ ++static int ralink_i2s_startup(struct snd_pcm_substream *substream, ++ struct snd_soc_dai *dai) ++{ ++ struct ralink_i2s *i2s = snd_soc_dai_get_drvdata(dai); ++ ++ if (dai->active) ++ return 0; ++ ++ /* setup status interrupt */ ++#if (RALINK_I2S_INT_EN) ++ regmap_write(i2s->regmap, I2S_REG_INT_EN, 0xff); ++#else ++ regmap_write(i2s->regmap, I2S_REG_INT_EN, 0x0); ++#endif ++ ++ /* enable */ ++ regmap_update_bits(i2s->regmap, I2S_REG_CFG0, ++ I2S_REG_CFG0_EN | I2S_REG_CFG0_DMA_EN | ++ I2S_REG_CFG0_THRES_MASK, ++ I2S_REG_CFG0_EN | I2S_REG_CFG0_DMA_EN | ++ I2S_REG_CFG0_DFT_THRES); ++ ++ return 0; ++} ++ ++static void ralink_i2s_shutdown(struct snd_pcm_substream *substream, ++ struct snd_soc_dai *dai) ++{ ++ struct ralink_i2s *i2s = snd_soc_dai_get_drvdata(dai); ++ ++ /* If both streams are stopped, disable module and clock */ ++ if (dai->active) ++ return; ++ ++ /* ++ * datasheet mention when disable all control regs are cleared ++ * to initial values. need reinit at startup. ++ */ ++ regmap_update_bits(i2s->regmap, I2S_REG_CFG0, I2S_REG_CFG0_EN, 0); ++} ++ ++static int ralink_i2s_hw_params(struct snd_pcm_substream *substream, ++ struct snd_pcm_hw_params *params, struct snd_soc_dai *dai) ++{ ++ struct ralink_i2s *i2s = snd_soc_dai_get_drvdata(dai); ++ int width; ++ int ret; ++ ++ width = params_width(params); ++ switch (width) { ++ case 16: ++ if (i2s->flags & RALINK_FLAGS_24BIT) ++ regmap_update_bits(i2s->regmap, I2S_REG_CFG0, ++ I2S_REG_CFG0_DATA_24, 0); ++ break; ++ case 24: ++ if (i2s->flags & RALINK_FLAGS_24BIT) { ++ regmap_update_bits(i2s->regmap, I2S_REG_CFG0, ++ I2S_REG_CFG0_DATA_24, ++ I2S_REG_CFG0_DATA_24); ++ break; ++ } ++ return -EINVAL; ++ default: ++ return -EINVAL; ++ } ++ ++ switch (params_channels(params)) { ++ case 2: ++ break; ++ default: ++ return -EINVAL; ++ } ++ ++ if (i2s->flags & RALINK_FLAGS_ENDIAN) { ++ /* system endian */ ++#ifdef SNDRV_LITTLE_ENDIAN ++ regmap_update_bits(i2s->regmap, I2S_REG_CFG0, ++ I2S_REG_CFG0_SYS_BE, 0); ++#else ++ regmap_update_bits(i2s->regmap, I2S_REG_CFG0, ++ I2S_REG_CFG0_SYS_BE, ++ I2S_REG_CFG0_SYS_BE); ++#endif ++ ++ /* data endian */ ++ switch (params_format(params)) { ++ case SNDRV_PCM_FORMAT_S16_LE: ++ case SNDRV_PCM_FORMAT_S24_LE: ++ regmap_update_bits(i2s->regmap, I2S_REG_CFG0, ++ I2S_REG_CFG0_FMT_LE, ++ I2S_REG_CFG0_FMT_LE); ++ break; ++ case SNDRV_PCM_FORMAT_S16_BE: ++ case SNDRV_PCM_FORMAT_S24_BE: ++ regmap_update_bits(i2s->regmap, I2S_REG_CFG0, ++ I2S_REG_CFG0_FMT_LE, 0); ++ break; ++ default: ++ return -EINVAL; ++ } ++ } ++ ++ /* setup bclk rate */ ++ if (i2s->flags & RALINK_FLAGS_TXONLY) ++ ret = ralink_i2s_set_sys_bclk(dai, width, params_rate(params)); ++ else ++ ret = ralink_i2s_set_bclk(dai, width, params_rate(params)); ++ ++ return ret; ++} ++ ++static int ralink_i2s_trigger(struct snd_pcm_substream *substream, int cmd, ++ struct snd_soc_dai *dai) ++{ ++ struct ralink_i2s *i2s = snd_soc_dai_get_drvdata(dai); ++ unsigned int mask, val; ++ ++ if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) ++ mask = I2S_REG_CFG0_TX_EN; ++ else ++ mask = I2S_REG_CFG0_RX_EN; ++ ++ switch (cmd) { ++ case SNDRV_PCM_TRIGGER_START: ++ case SNDRV_PCM_TRIGGER_RESUME: ++ case SNDRV_PCM_TRIGGER_PAUSE_RELEASE: ++ val = mask; ++ break; ++ case SNDRV_PCM_TRIGGER_STOP: ++ case SNDRV_PCM_TRIGGER_SUSPEND: ++ case SNDRV_PCM_TRIGGER_PAUSE_PUSH: ++ val = 0; ++ break; ++ default: ++ return -EINVAL; ++ } ++ ++ regmap_update_bits(i2s->regmap, I2S_REG_CFG0, mask, val); ++ ++ return 0; ++} ++ ++static void ralink_i2s_init_dma_data(struct ralink_i2s *i2s, ++ struct resource *res) ++{ ++ struct snd_dmaengine_dai_dma_data *dma_data; ++ ++ /* Playback */ ++ dma_data = &i2s->playback_dma_data; ++ dma_data->addr = res->start + I2S_REG_WREG; ++ dma_data->addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES; ++ dma_data->maxburst = 1; ++ dma_data->slave_id = i2s->txdma_req; ++ ++ if (i2s->flags & RALINK_FLAGS_TXONLY) ++ return; ++ ++ /* Capture */ ++ dma_data = &i2s->capture_dma_data; ++ dma_data->addr = res->start + I2S_REG_RREG; ++ dma_data->addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES; ++ dma_data->maxburst = 1; ++ dma_data->slave_id = i2s->rxdma_req; ++} ++ ++static int ralink_i2s_dai_probe(struct snd_soc_dai *dai) ++{ ++ struct ralink_i2s *i2s = snd_soc_dai_get_drvdata(dai); ++ ++ snd_soc_dai_init_dma_data(dai, &i2s->playback_dma_data, ++ &i2s->capture_dma_data); ++ ++ return 0; ++} ++ ++static int ralink_i2s_dai_remove(struct snd_soc_dai *dai) ++{ ++ return 0; ++} ++ ++static const struct snd_soc_dai_ops ralink_i2s_dai_ops = { ++ .set_sysclk = ralink_i2s_set_sysclk, ++ .set_fmt = ralink_i2s_set_fmt, ++ .startup = ralink_i2s_startup, ++ .shutdown = ralink_i2s_shutdown, ++ .hw_params = ralink_i2s_hw_params, ++ .trigger = ralink_i2s_trigger, ++}; ++ ++static struct snd_soc_dai_driver ralink_i2s_dai = { ++ .name = DRV_NAME, ++ .probe = ralink_i2s_dai_probe, ++ .remove = ralink_i2s_dai_remove, ++ .ops = &ralink_i2s_dai_ops, ++ .capture = { ++ .stream_name = "I2S Capture", ++ .channels_min = 2, ++ .channels_max = 2, ++ .rate_min = 5512, ++ .rate_max = 192000, ++ .rates = SNDRV_PCM_RATE_CONTINUOUS, ++ .formats = SNDRV_PCM_FMTBIT_S16_LE, ++ }, ++ .playback = { ++ .stream_name = "I2S Playback", ++ .channels_min = 2, ++ .channels_max = 2, ++ .rate_min = 5512, ++ .rate_max = 192000, ++ .rates = SNDRV_PCM_RATE_CONTINUOUS, ++ .formats = SNDRV_PCM_FMTBIT_S16_LE, ++ }, ++ .symmetric_rates = 1, ++}; ++ ++static struct snd_pcm_hardware ralink_pcm_hardware = { ++ .info = SNDRV_PCM_INFO_MMAP | ++ SNDRV_PCM_INFO_MMAP_VALID | ++ SNDRV_PCM_INFO_INTERLEAVED | ++ SNDRV_PCM_INFO_BLOCK_TRANSFER, ++ .formats = SNDRV_PCM_FMTBIT_S16_LE, ++ .channels_min = 2, ++ .channels_max = 2, ++ .period_bytes_min = PAGE_SIZE, ++ .period_bytes_max = PAGE_SIZE * 2, ++ .periods_min = 2, ++ .periods_max = 128, ++ .buffer_bytes_max = 128 * 1024, ++ .fifo_size = RALINK_I2S_FIFO_SIZE, ++}; ++ ++static const struct snd_dmaengine_pcm_config ralink_dmaengine_pcm_config = { ++ .prepare_slave_config = snd_dmaengine_pcm_prepare_slave_config, ++ .pcm_hardware = &ralink_pcm_hardware, ++ .prealloc_buffer_size = 256 * PAGE_SIZE, ++}; ++ ++static const struct snd_soc_component_driver ralink_i2s_component = { ++ .name = DRV_NAME, ++}; ++ ++static bool ralink_i2s_readable_reg(struct device *dev, unsigned int reg) ++{ ++ return true; ++} ++ ++static bool ralink_i2s_volatile_reg(struct device *dev, unsigned int reg) ++{ ++ switch (reg) { ++ case I2S_REG_INT_STATUS: ++ case I2S_REG_FF_STATUS: ++ return true; ++ } ++ return false; ++} ++ ++static bool ralink_i2s_writeable_reg(struct device *dev, unsigned int reg) ++{ ++ switch (reg) { ++ case I2S_REG_FF_STATUS: ++ case I2S_REG_RREG: ++ return false; ++ } ++ return true; ++} ++ ++static const struct regmap_config ralink_i2s_regmap_config = { ++ .reg_bits = 32, ++ .reg_stride = 4, ++ .val_bits = 32, ++ .writeable_reg = ralink_i2s_writeable_reg, ++ .readable_reg = ralink_i2s_readable_reg, ++ .volatile_reg = ralink_i2s_volatile_reg, ++ .max_register = I2S_REG_DIVINT, ++}; ++ ++#if (RALINK_I2S_INT_EN) ++static irqreturn_t ralink_i2s_irq(int irq, void *devid) ++{ ++ struct ralink_i2s *i2s = devid; ++ u32 status; ++ ++ regmap_read(i2s->regmap, I2S_REG_INT_STATUS, &status); ++ if (unlikely(!status)) ++ return IRQ_NONE; ++ ++ /* tx stats */ ++ if (status & I2S_REG_INT_TX_MASK) { ++ if (status & I2S_REG_INT_TX_THRES) ++ i2s->txstats.belowthres++; ++ if (status & I2S_REG_INT_TX_UNRUN) ++ i2s->txstats.underrun++; ++ if (status & I2S_REG_INT_TX_OVRUN) ++ i2s->txstats.overrun++; ++ if (status & I2S_REG_INT_TX_FAULT) ++ i2s->txstats.dmafault++; ++ } ++ ++ /* rx stats */ ++ if (status & I2S_REG_INT_RX_MASK) { ++ if (status & I2S_REG_INT_RX_THRES) ++ i2s->rxstats.belowthres++; ++ if (status & I2S_REG_INT_RX_UNRUN) ++ i2s->rxstats.underrun++; ++ if (status & I2S_REG_INT_RX_OVRUN) ++ i2s->rxstats.overrun++; ++ if (status & I2S_REG_INT_RX_FAULT) ++ i2s->rxstats.dmafault++; ++ } ++ ++ /* clean status bits */ ++ regmap_write(i2s->regmap, I2S_REG_INT_STATUS, status); ++ ++ return IRQ_HANDLED; ++} ++#endif ++ ++#if IS_ENABLED(CONFIG_DEBUG_FS) ++static int ralink_i2s_stats_show(struct seq_file *s, void *unused) ++{ ++ struct ralink_i2s *i2s = s->private; ++ ++ seq_printf(s, "tx stats\n"); ++ seq_printf(s, "\tbelow threshold\t%u\n", i2s->txstats.belowthres); ++ seq_printf(s, "\tunder run\t%u\n", i2s->txstats.underrun); ++ seq_printf(s, "\tover run\t%u\n", i2s->txstats.overrun); ++ seq_printf(s, "\tdma fault\t%u\n", i2s->txstats.dmafault); ++ ++ seq_printf(s, "rx stats\n"); ++ seq_printf(s, "\tbelow threshold\t%u\n", i2s->rxstats.belowthres); ++ seq_printf(s, "\tunder run\t%u\n", i2s->rxstats.underrun); ++ seq_printf(s, "\tover run\t%u\n", i2s->rxstats.overrun); ++ seq_printf(s, "\tdma fault\t%u\n", i2s->rxstats.dmafault); ++ ++ ralink_i2s_dump_regs(i2s); ++ ++ return 0; ++} ++ ++static int ralink_i2s_stats_open(struct inode *inode, struct file *file) ++{ ++ return single_open(file, ralink_i2s_stats_show, inode->i_private); ++} ++ ++static const struct file_operations ralink_i2s_stats_ops = { ++ .open = ralink_i2s_stats_open, ++ .read = seq_read, ++ .llseek = seq_lseek, ++ .release = single_release, ++}; ++ ++static inline int ralink_i2s_debugfs_create(struct ralink_i2s *i2s) ++{ ++ i2s->dbg_dir = debugfs_create_dir(dev_name(i2s->dev), NULL); ++ if (!i2s->dbg_dir) ++ return -ENOMEM; ++ ++ i2s->dbg_stats = debugfs_create_file("stats", S_IRUGO, ++ i2s->dbg_dir, i2s, &ralink_i2s_stats_ops); ++ if (!i2s->dbg_stats) { ++ debugfs_remove(i2s->dbg_dir); ++ return -ENOMEM; ++ } ++ ++ return 0; ++} ++ ++static inline void ralink_i2s_debugfs_remove(struct ralink_i2s *i2s) ++{ ++ debugfs_remove(i2s->dbg_stats); ++ debugfs_remove(i2s->dbg_dir); ++} ++#else ++static inline int ralink_i2s_debugfs_create(struct ralink_i2s *i2s) ++{ ++ return 0; ++} ++ ++static inline void ralink_i2s_debugfs_remove(struct fsl_ssi_dbg *ssi_dbg) ++{ ++} ++#endif ++ ++/* ++ * TODO: these refclk setup functions should use ++ * clock framework instead. hardcode it now. ++ */ ++static void rt3350_refclk_setup(void) ++{ ++ uint32_t data; ++ ++ /* set refclk output 12Mhz clock */ ++ data = rt_sysc_r32(0x2c); ++ data |= (0x1 << 8); ++ rt_sysc_w32(data, 0x2c); ++} ++ ++static void rt3883_refclk_setup(void) ++{ ++ uint32_t data; ++ ++ /* set refclk output 12Mhz clock */ ++ data = rt_sysc_r32(0x2c); ++ data &= ~(0x3 << 13); ++ data |= (0x1 << 13); ++ rt_sysc_w32(data, 0x2c); ++} ++ ++static void rt3552_refclk_setup(void) ++{ ++ uint32_t data; ++ ++ /* set refclk output 12Mhz clock */ ++ data = rt_sysc_r32(0x2c); ++ data &= ~(0xf << 8); ++ data |= (0x3 << 8); ++ rt_sysc_w32(data, 0x2c); ++} ++ ++static void mt7620_refclk_setup(void) ++{ ++ uint32_t data; ++ ++ /* set refclk output 12Mhz clock */ ++ data = rt_sysc_r32(0x2c); ++ data &= ~(0x7 << 9); ++ data |= 0x1 << 9; ++ rt_sysc_w32(data, 0x2c); ++} ++ ++static void mt7621_refclk_setup(void) ++{ ++ uint32_t data; ++ ++ /* set refclk output 12Mhz clock */ ++ data = rt_sysc_r32(0x2c); ++ data &= ~(0x1f << 18); ++ data |= (0x19 << 18); ++ data &= ~(0x1f << 12); ++ data |= (0x1 << 12); ++ data &= ~(0x7 << 9); ++ data |= (0x5 << 9); ++ rt_sysc_w32(data, 0x2c); ++} ++ ++static void mt7628_refclk_setup(void) ++{ ++ uint32_t data; ++ ++ /* set i2s and refclk digital pad */ ++ data = rt_sysc_r32(0x3c); ++ data |= 0x1f; ++ rt_sysc_w32(data, 0x3c); ++ ++ /* Adjust REFCLK0's driving strength */ ++ data = rt_sysc_r32(0x1354); ++ data &= ~(0x1 << 5); ++ rt_sysc_w32(data, 0x1354); ++ data = rt_sysc_r32(0x1364); ++ data |= ~(0x1 << 5); ++ rt_sysc_w32(data, 0x1364); ++ ++ /* set refclk output 12Mhz clock */ ++ data = rt_sysc_r32(0x2c); ++ data &= ~(0x7 << 9); ++ data |= 0x1 << 9; ++ rt_sysc_w32(data, 0x2c); ++} ++ ++struct rt_i2s_data { ++ u32 flags; ++ void (*refclk_setup)(void); ++}; ++ ++struct rt_i2s_data rt3050_i2s_data = { .flags = RALINK_FLAGS_TXONLY }; ++struct rt_i2s_data rt3350_i2s_data = { .flags = RALINK_FLAGS_TXONLY, ++ .refclk_setup = rt3350_refclk_setup }; ++struct rt_i2s_data rt3883_i2s_data = { ++ .flags = (RALINK_FLAGS_LEFT_J | RALINK_FLAGS_RIGHT_J), ++ .refclk_setup = rt3883_refclk_setup }; ++struct rt_i2s_data rt3352_i2s_data = { .refclk_setup = rt3552_refclk_setup}; ++struct rt_i2s_data mt7620_i2s_data = { .refclk_setup = mt7620_refclk_setup}; ++struct rt_i2s_data mt7621_i2s_data = { .refclk_setup = mt7621_refclk_setup}; ++struct rt_i2s_data mt7628_i2s_data = { ++ .flags = (RALINK_FLAGS_ENDIAN | RALINK_FLAGS_24BIT | ++ RALINK_FLAGS_LEFT_J), ++ .refclk_setup = mt7628_refclk_setup}; ++ ++static const struct of_device_id ralink_i2s_match_table[] = { ++ { .compatible = "ralink,rt3050-i2s", ++ .data = (void *)&rt3050_i2s_data }, ++ { .compatible = "ralink,rt3350-i2s", ++ .data = (void *)&rt3350_i2s_data }, ++ { .compatible = "ralink,rt3883-i2s", ++ .data = (void *)&rt3883_i2s_data }, ++ { .compatible = "ralink,rt3352-i2s", ++ .data = (void *)&rt3352_i2s_data }, ++ { .compatible = "mediatek,mt7620-i2s", ++ .data = (void *)&mt7620_i2s_data }, ++ { .compatible = "mediatek,mt7621-i2s", ++ .data = (void *)&mt7621_i2s_data }, ++ { .compatible = "mediatek,mt7628-i2s", ++ .data = (void *)&mt7628_i2s_data }, ++}; ++MODULE_DEVICE_TABLE(of, ralink_i2s_match_table); ++ ++static int ralink_i2s_probe(struct platform_device *pdev) ++{ ++ const struct of_device_id *match; ++ struct device_node *np = pdev->dev.of_node; ++ struct ralink_i2s *i2s; ++ struct resource *res; ++ int irq, ret; ++ u32 dma_req; ++ struct rt_i2s_data *data; ++ ++ i2s = devm_kzalloc(&pdev->dev, sizeof(*i2s), GFP_KERNEL); ++ if (!i2s) ++ return -ENOMEM; ++ ++ platform_set_drvdata(pdev, i2s); ++ i2s->dev = &pdev->dev; ++ ++ match = of_match_device(ralink_i2s_match_table, &pdev->dev); ++ if (!match) ++ return -EINVAL; ++ data = (struct rt_i2s_data *)match->data; ++ i2s->flags = data->flags; ++ /* setup out 12Mhz refclk to codec as mclk */ ++ if (data->refclk_setup) ++ data->refclk_setup(); ++ ++ if (of_property_read_u32(np, "txdma-req", &dma_req)) { ++ dev_err(&pdev->dev, "no txdma-req define\n"); ++ return -EINVAL; ++ } ++ i2s->txdma_req = (u16)dma_req; ++ if (!(i2s->flags & RALINK_FLAGS_TXONLY)) { ++ if (of_property_read_u32(np, "rxdma-req", &dma_req)) { ++ dev_err(&pdev->dev, "no rxdma-req define\n"); ++ return -EINVAL; ++ } ++ i2s->rxdma_req = (u16)dma_req; ++ } ++ ++ res = platform_get_resource(pdev, IORESOURCE_MEM, 0); ++ i2s->regs = devm_ioremap_resource(&pdev->dev, res); ++ if (IS_ERR(i2s->regs)) ++ return PTR_ERR(i2s->regs); ++ ++ i2s->regmap = devm_regmap_init_mmio(&pdev->dev, i2s->regs, ++ &ralink_i2s_regmap_config); ++ if (IS_ERR(i2s->regmap)) { ++ dev_err(&pdev->dev, "regmap init failed\n"); ++ return PTR_ERR(i2s->regmap); ++ } ++ ++ irq = platform_get_irq(pdev, 0); ++ if (irq < 0) { ++ dev_err(&pdev->dev, "failed to get irq\n"); ++ return -EINVAL; ++ } ++ ++#if (RALINK_I2S_INT_EN) ++ ret = devm_request_irq(&pdev->dev, irq, ralink_i2s_irq, ++ 0, dev_name(&pdev->dev), i2s); ++ if (ret) { ++ dev_err(&pdev->dev, "failed to request irq\n"); ++ return ret; ++ } ++#endif ++ ++ i2s->clk = devm_clk_get(&pdev->dev, NULL); ++ if (IS_ERR(i2s->clk)) { ++ dev_err(&pdev->dev, "no clock defined\n"); ++ return PTR_ERR(i2s->clk); ++ } ++ ++ ret = clk_prepare_enable(i2s->clk); ++ if (ret) ++ return ret; ++ ++ ralink_i2s_init_dma_data(i2s, res); ++ ++ device_reset(&pdev->dev); ++ ++ ret = ralink_i2s_debugfs_create(i2s); ++ if (ret) { ++ dev_err(&pdev->dev, "create debugfs failed\n"); ++ goto err_clk_disable; ++ } ++ ++ /* enable 24bits support */ ++ if (i2s->flags & RALINK_FLAGS_24BIT) { ++ ralink_i2s_dai.capture.formats |= SNDRV_PCM_FMTBIT_S24_LE; ++ ralink_i2s_dai.playback.formats |= SNDRV_PCM_FMTBIT_S24_LE; ++ } ++ ++ /* enable big endian support */ ++ if (i2s->flags & RALINK_FLAGS_ENDIAN) { ++ ralink_i2s_dai.capture.formats |= SNDRV_PCM_FMTBIT_S16_BE; ++ ralink_i2s_dai.playback.formats |= SNDRV_PCM_FMTBIT_S16_BE; ++ ralink_pcm_hardware.formats |= SNDRV_PCM_FMTBIT_S16_BE; ++ if (i2s->flags & RALINK_FLAGS_24BIT) { ++ ralink_i2s_dai.capture.formats |= ++ SNDRV_PCM_FMTBIT_S24_BE; ++ ralink_i2s_dai.playback.formats |= ++ SNDRV_PCM_FMTBIT_S24_BE; ++ ralink_pcm_hardware.formats |= ++ SNDRV_PCM_FMTBIT_S24_BE; ++ } ++ } ++ ++ /* disable capture support */ ++ if (i2s->flags & RALINK_FLAGS_TXONLY) ++ memset(&ralink_i2s_dai.capture, sizeof(ralink_i2s_dai.capture), ++ 0); ++ ++ ret = devm_snd_soc_register_component(&pdev->dev, &ralink_i2s_component, ++ &ralink_i2s_dai, 1); ++ if (ret) ++ goto err_debugfs; ++ ++ ret = devm_snd_dmaengine_pcm_register(&pdev->dev, ++ &ralink_dmaengine_pcm_config, ++ SND_DMAENGINE_PCM_FLAG_COMPAT); ++ if (ret) ++ goto err_debugfs; ++ ++ dev_info(i2s->dev, "mclk %luMHz\n", clk_get_rate(i2s->clk) / 1000000); ++ ++ return 0; ++ ++err_debugfs: ++ ralink_i2s_debugfs_remove(i2s); ++ ++err_clk_disable: ++ clk_disable_unprepare(i2s->clk); ++ ++ return ret; ++} ++ ++static int ralink_i2s_remove(struct platform_device *pdev) ++{ ++ struct ralink_i2s *i2s = platform_get_drvdata(pdev); ++ ++ ralink_i2s_debugfs_remove(i2s); ++ clk_disable_unprepare(i2s->clk); ++ ++ return 0; ++} ++ ++static struct platform_driver ralink_i2s_driver = { ++ .probe = ralink_i2s_probe, ++ .remove = ralink_i2s_remove, ++ .driver = { ++ .name = DRV_NAME, ++ .of_match_table = ralink_i2s_match_table, ++ }, ++}; ++module_platform_driver(ralink_i2s_driver); ++ ++MODULE_AUTHOR("Lars-Peter Clausen, "); ++MODULE_DESCRIPTION("Ralink/MediaTek I2S driver"); ++MODULE_LICENSE("GPL"); ++MODULE_ALIAS("platform:" DRV_NAME); diff --git a/target/linux/ramips/patches-5.4/0051-serial-add-ugly-custom-baud-rate-hack.patch b/target/linux/ramips/patches-5.4/0051-serial-add-ugly-custom-baud-rate-hack.patch new file mode 100644 index 0000000000..2ad1f6f9f8 --- /dev/null +++ b/target/linux/ramips/patches-5.4/0051-serial-add-ugly-custom-baud-rate-hack.patch @@ -0,0 +1,22 @@ +From a7eb46e0ea4a11e4dfb56ab129bf816d1059a6c5 Mon Sep 17 00:00:00 2001 +From: John Crispin +Date: Mon, 7 Dec 2015 17:31:08 +0100 +Subject: [PATCH 51/53] serial: add ugly custom baud rate hack + +Signed-off-by: John Crispin +--- + drivers/tty/serial/serial_core.c | 3 +++ + 1 file changed, 3 insertions(+) + +--- a/drivers/tty/serial/serial_core.c ++++ b/drivers/tty/serial/serial_core.c +@@ -428,6 +428,9 @@ uart_get_baud_rate(struct uart_port *por + break; + } + ++ if (tty_termios_baud_rate(termios) == 2500000) ++ return 250000; ++ + for (try = 0; try < 2; try++) { + baud = tty_termios_baud_rate(termios); + diff --git a/target/linux/ramips/patches-5.4/0052-pwm-add-mediatek-support.patch b/target/linux/ramips/patches-5.4/0052-pwm-add-mediatek-support.patch new file mode 100644 index 0000000000..6eb7f16b9d --- /dev/null +++ b/target/linux/ramips/patches-5.4/0052-pwm-add-mediatek-support.patch @@ -0,0 +1,217 @@ +From fc8f96309c21c1bc3276427309cd7d361347d66e Mon Sep 17 00:00:00 2001 +From: John Crispin +Date: Mon, 7 Dec 2015 17:16:50 +0100 +Subject: [PATCH 52/53] pwm: add mediatek support + +Signed-off-by: John Crispin +--- + drivers/pwm/Kconfig | 9 +++ + drivers/pwm/Makefile | 1 + + drivers/pwm/pwm-mediatek.c | 173 ++++++++++++++++++++++++++++++++++++++++++++ + 3 files changed, 183 insertions(+) + create mode 100644 drivers/pwm/pwm-mediatek.c + +--- a/drivers/pwm/Kconfig ++++ b/drivers/pwm/Kconfig +@@ -302,6 +302,15 @@ config PWM_MEDIATEK + To compile this driver as a module, choose M here: the module + will be called pwm-mediatek. + ++config PWM_MEDIATEK_RAMIPS ++ tristate "Mediatek PWM support" ++ depends on RALINK && OF ++ help ++ Generic PWM framework driver for Mediatek ARM SoC. ++ ++ To compile this driver as a module, choose M here: the module ++ will be called pwm-mxs. ++ + config PWM_MXS + tristate "Freescale MXS PWM support" + depends on ARCH_MXS && OF +--- a/drivers/pwm/Makefile ++++ b/drivers/pwm/Makefile +@@ -28,6 +28,7 @@ obj-$(CONFIG_PWM_LPSS_PCI) += pwm-lpss-p + obj-$(CONFIG_PWM_LPSS_PLATFORM) += pwm-lpss-platform.o + obj-$(CONFIG_PWM_MESON) += pwm-meson.o + obj-$(CONFIG_PWM_MEDIATEK) += pwm-mediatek.o ++obj-$(CONFIG_PWM_MEDIATEK_RAMIPS) += pwm-mediatek-ramips.o + obj-$(CONFIG_PWM_MTK_DISP) += pwm-mtk-disp.o + obj-$(CONFIG_PWM_MXS) += pwm-mxs.o + obj-$(CONFIG_PWM_OMAP_DMTIMER) += pwm-omap-dmtimer.o +--- /dev/null ++++ b/drivers/pwm/pwm-mediatek-ramips.c +@@ -0,0 +1,173 @@ ++/* ++ * Mediatek Pulse Width Modulator driver ++ * ++ * Copyright (C) 2015 John Crispin ++ * ++ * This file is licensed under the terms of the GNU General Public ++ * License version 2. This program is licensed "as is" without any ++ * warranty of any kind, whether express or implied. ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#define NUM_PWM 4 ++ ++/* PWM registers and bits definitions */ ++#define PWMCON 0x00 ++#define PWMHDUR 0x04 ++#define PWMLDUR 0x08 ++#define PWMGDUR 0x0c ++#define PWMWAVENUM 0x28 ++#define PWMDWIDTH 0x2c ++#define PWMTHRES 0x30 ++ ++/** ++ * struct mtk_pwm_chip - struct representing pwm chip ++ * ++ * @mmio_base: base address of pwm chip ++ * @chip: linux pwm chip representation ++ */ ++struct mtk_pwm_chip { ++ void __iomem *mmio_base; ++ struct pwm_chip chip; ++}; ++ ++static inline struct mtk_pwm_chip *to_mtk_pwm_chip(struct pwm_chip *chip) ++{ ++ return container_of(chip, struct mtk_pwm_chip, chip); ++} ++ ++static inline u32 mtk_pwm_readl(struct mtk_pwm_chip *chip, unsigned int num, ++ unsigned long offset) ++{ ++ return ioread32(chip->mmio_base + 0x10 + (num * 0x40) + offset); ++} ++ ++static inline void mtk_pwm_writel(struct mtk_pwm_chip *chip, ++ unsigned int num, unsigned long offset, ++ unsigned long val) ++{ ++ iowrite32(val, chip->mmio_base + 0x10 + (num * 0x40) + offset); ++} ++ ++static int mtk_pwm_config(struct pwm_chip *chip, struct pwm_device *pwm, ++ int duty_ns, int period_ns) ++{ ++ struct mtk_pwm_chip *pc = to_mtk_pwm_chip(chip); ++ u32 resolution = 100 / 4; ++ u32 clkdiv = 0; ++ ++ while (period_ns / resolution > 8191) { ++ clkdiv++; ++ resolution *= 2; ++ } ++ ++ if (clkdiv > 7) ++ return -1; ++ ++ mtk_pwm_writel(pc, pwm->hwpwm, PWMCON, BIT(15) | BIT(3) | clkdiv); ++ mtk_pwm_writel(pc, pwm->hwpwm, PWMDWIDTH, period_ns / resolution); ++ mtk_pwm_writel(pc, pwm->hwpwm, PWMTHRES, duty_ns / resolution); ++ return 0; ++} ++ ++static int mtk_pwm_enable(struct pwm_chip *chip, struct pwm_device *pwm) ++{ ++ struct mtk_pwm_chip *pc = to_mtk_pwm_chip(chip); ++ u32 val; ++ ++ val = ioread32(pc->mmio_base); ++ val |= BIT(pwm->hwpwm); ++ iowrite32(val, pc->mmio_base); ++ ++ return 0; ++} ++ ++static void mtk_pwm_disable(struct pwm_chip *chip, struct pwm_device *pwm) ++{ ++ struct mtk_pwm_chip *pc = to_mtk_pwm_chip(chip); ++ u32 val; ++ ++ val = ioread32(pc->mmio_base); ++ val &= ~BIT(pwm->hwpwm); ++ iowrite32(val, pc->mmio_base); ++} ++ ++static const struct pwm_ops mtk_pwm_ops = { ++ .config = mtk_pwm_config, ++ .enable = mtk_pwm_enable, ++ .disable = mtk_pwm_disable, ++ .owner = THIS_MODULE, ++}; ++ ++static int mtk_pwm_probe(struct platform_device *pdev) ++{ ++ struct mtk_pwm_chip *pc; ++ struct resource *r; ++ int ret; ++ ++ pc = devm_kzalloc(&pdev->dev, sizeof(*pc), GFP_KERNEL); ++ if (!pc) ++ return -ENOMEM; ++ ++ r = platform_get_resource(pdev, IORESOURCE_MEM, 0); ++ pc->mmio_base = devm_ioremap_resource(&pdev->dev, r); ++ if (IS_ERR(pc->mmio_base)) ++ return PTR_ERR(pc->mmio_base); ++ ++ platform_set_drvdata(pdev, pc); ++ ++ pc->chip.dev = &pdev->dev; ++ pc->chip.ops = &mtk_pwm_ops; ++ pc->chip.base = -1; ++ pc->chip.npwm = NUM_PWM; ++ ++ ret = pwmchip_add(&pc->chip); ++ if (ret < 0) ++ dev_err(&pdev->dev, "pwmchip_add() failed: %d\n", ret); ++ ++ return ret; ++} ++ ++static int mtk_pwm_remove(struct platform_device *pdev) ++{ ++ struct mtk_pwm_chip *pc = platform_get_drvdata(pdev); ++ int i; ++ ++ for (i = 0; i < NUM_PWM; i++) ++ pwm_disable(&pc->chip.pwms[i]); ++ ++ return pwmchip_remove(&pc->chip); ++} ++ ++static const struct of_device_id mtk_pwm_of_match[] = { ++ { .compatible = "mediatek,mt7628-pwm" }, ++ { } ++}; ++ ++MODULE_DEVICE_TABLE(of, mtk_pwm_of_match); ++ ++static struct platform_driver mtk_pwm_driver = { ++ .driver = { ++ .name = "mtk-pwm", ++ .owner = THIS_MODULE, ++ .of_match_table = mtk_pwm_of_match, ++ }, ++ .probe = mtk_pwm_probe, ++ .remove = mtk_pwm_remove, ++}; ++ ++module_platform_driver(mtk_pwm_driver); ++ ++MODULE_LICENSE("GPL"); ++MODULE_AUTHOR("John Crispin "); ++MODULE_ALIAS("platform:mtk-pwm"); diff --git a/target/linux/ramips/patches-5.4/0053-mtd-spi-nor-add-w25q256-3b-mode-switch.patch b/target/linux/ramips/patches-5.4/0053-mtd-spi-nor-add-w25q256-3b-mode-switch.patch new file mode 100644 index 0000000000..aa2fb60a2b --- /dev/null +++ b/target/linux/ramips/patches-5.4/0053-mtd-spi-nor-add-w25q256-3b-mode-switch.patch @@ -0,0 +1,214 @@ +mtd: spi-nor: add support for switching between 3-byte and 4-byte addressing on w25q256 flash + +On some devices the flash chip needs to be in 3-byte addressing mode during +reboot, otherwise the boot loader will fail to start. +This mode however does not allow regular reads/writes onto the upper 16M +half. W25Q256 has separate read commands for reading from >16M, however +it does not have any separate write commands. +This patch changes the code to leave the chip in 3-byte mode most of the +time and only switch during erase/write cycles that go to >16M +addresses. + +Signed-off-by: Felix Fietkau +--- +--- a/drivers/mtd/spi-nor/spi-nor.c ++++ b/drivers/mtd/spi-nor/spi-nor.c +@@ -89,6 +89,10 @@ struct flash_info { + #define NO_CHIP_ERASE BIT(12) /* Chip does not support chip erase */ + #define SPI_NOR_SKIP_SFDP BIT(13) /* Skip parsing of SFDP tables */ + #define USE_CLSR BIT(14) /* use CLSR command */ ++#define SPI_NOR_4B_READ_OP BIT(15) /* ++ * Like SPI_NOR_4B_OPCODES, but for read ++ * op code only. ++ */ + }; + + #define JEDEC_MFR(info) ((info)->id[0]) +@@ -240,6 +244,15 @@ static inline u8 spi_nor_convert_3to4_er + ARRAY_SIZE(spi_nor_3to4_erase)); + } + ++static void spi_nor_set_4byte_read(struct spi_nor *nor, ++ const struct flash_info *info) ++{ ++ nor->addr_width = 3; ++ nor->ext_addr = 0; ++ nor->read_opcode = spi_nor_convert_3to4_read(nor->read_opcode); ++ nor->flags |= SNOR_F_4B_EXT_ADDR; ++} ++ + static void spi_nor_set_4byte_opcodes(struct spi_nor *nor, + const struct flash_info *info) + { +@@ -467,6 +480,36 @@ static int spi_nor_erase_sector(struct s + return nor->write_reg(nor, nor->erase_opcode, buf, nor->addr_width); + } + ++static int spi_nor_check_ext_addr(struct spi_nor *nor, u32 addr) ++{ ++ bool ext_addr; ++ int ret; ++ u8 cmd; ++ ++ if (!(nor->flags & SNOR_F_4B_EXT_ADDR)) ++ return 0; ++ ++ ext_addr = !!(addr & 0xff000000); ++ if (nor->ext_addr == ext_addr) ++ return 0; ++ ++ cmd = ext_addr ? SPINOR_OP_EN4B : SPINOR_OP_EX4B; ++ write_enable(nor); ++ ret = nor->write_reg(nor, cmd, NULL, 0); ++ if (ret) ++ return ret; ++ ++ cmd = 0; ++ ret = nor->write_reg(nor, SPINOR_OP_WREAR, &cmd, 1); ++ if (ret) ++ return ret; ++ ++ nor->addr_width = 3 + ext_addr; ++ nor->ext_addr = ext_addr; ++ write_disable(nor); ++ return 0; ++} ++ + /* + * Erase an address range on the nor chip. The address range may extend + * one or more erase sectors. Return an error is there is a problem erasing. +@@ -492,6 +535,10 @@ static int spi_nor_erase(struct mtd_info + if (ret) + return ret; + ++ ret = spi_nor_check_ext_addr(nor, addr + len); ++ if (ret) ++ return ret; ++ + /* whole-chip erase? */ + if (len == mtd->size && !(nor->flags & SNOR_F_NO_OP_CHIP_ERASE)) { + unsigned long timeout; +@@ -542,6 +589,7 @@ static int spi_nor_erase(struct mtd_info + write_disable(nor); + + erase_err: ++ spi_nor_check_ext_addr(nor, 0); + spi_nor_unlock_and_unprep(nor, SPI_NOR_OPS_ERASE); + + instr->state = ret ? MTD_ERASE_FAILED : MTD_ERASE_DONE; +@@ -834,7 +882,9 @@ static int spi_nor_lock(struct mtd_info + if (ret) + return ret; + ++ spi_nor_check_ext_addr(nor, ofs + len); + ret = nor->flash_lock(nor, ofs, len); ++ spi_nor_check_ext_addr(nor, 0); + + spi_nor_unlock_and_unprep(nor, SPI_NOR_OPS_UNLOCK); + return ret; +@@ -849,7 +899,9 @@ static int spi_nor_unlock(struct mtd_inf + if (ret) + return ret; + ++ spi_nor_check_ext_addr(nor, ofs + len); + ret = nor->flash_unlock(nor, ofs, len); ++ spi_nor_check_ext_addr(nor, 0); + + spi_nor_unlock_and_unprep(nor, SPI_NOR_OPS_LOCK); + return ret; +@@ -1182,7 +1234,7 @@ static const struct flash_info spi_nor_i + { "w25q80", INFO(0xef5014, 0, 64 * 1024, 16, SECT_4K) }, + { "w25q80bl", INFO(0xef4014, 0, 64 * 1024, 16, SECT_4K) }, + { "w25q128", INFO(0xef4018, 0, 64 * 1024, 256, SECT_4K) }, +- { "w25q256", INFO(0xef4019, 0, 64 * 1024, 512, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) }, ++ { "w25q256", INFO(0xef4019, 0, 64 * 1024, 512, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_READ_OP) }, + { "w25m512jv", INFO(0xef7119, 0, 64 * 1024, 1024, + SECT_4K | SPI_NOR_QUAD_READ | SPI_NOR_DUAL_READ) }, + +@@ -1245,6 +1297,9 @@ static int spi_nor_read(struct mtd_info + if (ret) + return ret; + ++ if (nor->flags & SNOR_F_4B_EXT_ADDR) ++ nor->addr_width = 4; ++ + while (len) { + loff_t addr = from; + +@@ -1269,6 +1324,18 @@ static int spi_nor_read(struct mtd_info + ret = 0; + + read_err: ++ if (nor->flags & SNOR_F_4B_EXT_ADDR) { ++ u8 val = 0; ++ ++ if ((from + len) & 0xff000000) { ++ write_enable(nor); ++ nor->write_reg(nor, SPINOR_OP_WREAR, &val, 1); ++ write_disable(nor); ++ } ++ ++ nor->addr_width = 3; ++ } ++ + spi_nor_unlock_and_unprep(nor, SPI_NOR_OPS_READ); + return ret; + } +@@ -1370,6 +1437,10 @@ static int spi_nor_write(struct mtd_info + if (ret) + return ret; + ++ ret = spi_nor_check_ext_addr(nor, to + len); ++ if (ret < 0) ++ return ret; ++ + for (i = 0; i < len; ) { + ssize_t written; + loff_t addr = to + i; +@@ -1410,6 +1481,7 @@ static int spi_nor_write(struct mtd_info + } + + write_err: ++ spi_nor_check_ext_addr(nor, 0); + spi_nor_unlock_and_unprep(nor, SPI_NOR_OPS_WRITE); + return ret; + } +@@ -2826,8 +2898,10 @@ int spi_nor_scan(struct spi_nor *nor, co + } else if (mtd->size > 0x1000000) { + /* enable 4-byte addressing if the device exceeds 16MiB */ + nor->addr_width = 4; +- if (JEDEC_MFR(info) == SNOR_MFR_SPANSION || +- info->flags & SPI_NOR_4B_OPCODES) ++ if (info->flags & SPI_NOR_4B_READ_OP) ++ spi_nor_set_4byte_read(nor, info); ++ else if (JEDEC_MFR(info) == SNOR_MFR_SPANSION || ++ info->flags & SPI_NOR_4B_OPCODES) + spi_nor_set_4byte_opcodes(nor, info); + else + set_4byte(nor, info, 1); +--- a/include/linux/mtd/spi-nor.h ++++ b/include/linux/mtd/spi-nor.h +@@ -102,6 +102,7 @@ + /* Used for Macronix and Winbond flashes. */ + #define SPINOR_OP_EN4B 0xb7 /* Enter 4-byte mode */ + #define SPINOR_OP_EX4B 0xe9 /* Exit 4-byte mode */ ++#define SPINOR_OP_WREAR 0xc5 /* Write extended address register */ + + /* Used for Spansion flashes only. */ + #define SPINOR_OP_BRWR 0x17 /* Bank register write */ +@@ -229,6 +230,7 @@ enum spi_nor_option_flags { + SNOR_F_S3AN_ADDR_DEFAULT = BIT(3), + SNOR_F_READY_XSR_RDY = BIT(4), + SNOR_F_USE_CLSR = BIT(5), ++ SNOR_F_4B_EXT_ADDR = BIT(6), + }; + + /** +@@ -280,6 +282,7 @@ struct spi_nor { + enum spi_nor_protocol reg_proto; + bool sst_write_second; + u32 flags; ++ u8 ext_addr; + u8 cmd_buf[SPI_NOR_MAX_CMD_SIZE]; + + int (*prepare)(struct spi_nor *nor, enum spi_nor_ops ops); diff --git a/target/linux/ramips/patches-5.4/0054-mtd-spi-nor-w25q256-respect-default-mode.patch b/target/linux/ramips/patches-5.4/0054-mtd-spi-nor-w25q256-respect-default-mode.patch new file mode 100644 index 0000000000..a686937989 --- /dev/null +++ b/target/linux/ramips/patches-5.4/0054-mtd-spi-nor-w25q256-respect-default-mode.patch @@ -0,0 +1,73 @@ +--- a/drivers/mtd/spi-nor/spi-nor.c ++++ b/drivers/mtd/spi-nor/spi-nor.c +@@ -142,20 +142,29 @@ static int read_fsr(struct spi_nor *nor) + * location. Return the configuration register value. + * Returns negative if error occurred. + */ +-static int read_cr(struct spi_nor *nor) ++static int _read_cr(struct spi_nor *nor, u8 reg) + { + int ret; + u8 val; + +- ret = nor->read_reg(nor, SPINOR_OP_RDCR, &val, 1); ++ ret = nor->read_reg(nor, reg, &val, 1); + if (ret < 0) { +- dev_err(nor->dev, "error %d reading CR\n", ret); ++ dev_err(nor->dev, "error %d reading %s\n", ret, ++ (reg==SPINOR_OP_RDCR)?"CR":"XCR"); + return ret; + } + + return val; + } + ++static inline int read_cr(struct spi_nor *nor) { ++ return _read_cr(nor, SPINOR_OP_RDCR); ++} ++ ++static inline int read_xcr(struct spi_nor *nor) { ++ return _read_cr(nor, SPINOR_OP_RDXCR); ++} ++ + /* + * Write status register 1 byte + * Returns negative if error occurred. +@@ -2898,9 +2907,16 @@ int spi_nor_scan(struct spi_nor *nor, co + } else if (mtd->size > 0x1000000) { + /* enable 4-byte addressing if the device exceeds 16MiB */ + nor->addr_width = 4; +- if (info->flags & SPI_NOR_4B_READ_OP) +- spi_nor_set_4byte_read(nor, info); +- else if (JEDEC_MFR(info) == SNOR_MFR_SPANSION || ++ if (info->flags & SPI_NOR_4B_READ_OP) { ++ if (JEDEC_MFR(info) == SNOR_MFR_WINBOND) { ++ ret = read_xcr(nor); ++ if (!(ret > 0 && (ret & XCR_DEF_4B_ADDR_MODE))) ++ spi_nor_set_4byte_read(nor, info); ++ else ++ set_4byte(nor, info, 1); ++ } else ++ spi_nor_set_4byte_read(nor, info); ++ } else if (JEDEC_MFR(info) == SNOR_MFR_SPANSION || + info->flags & SPI_NOR_4B_OPCODES) + spi_nor_set_4byte_opcodes(nor, info); + else +--- a/include/linux/mtd/spi-nor.h ++++ b/include/linux/mtd/spi-nor.h +@@ -103,6 +103,7 @@ + #define SPINOR_OP_EN4B 0xb7 /* Enter 4-byte mode */ + #define SPINOR_OP_EX4B 0xe9 /* Exit 4-byte mode */ + #define SPINOR_OP_WREAR 0xc5 /* Write extended address register */ ++#define SPINOR_OP_RDXCR 0x15 /* Read extended configuration register */ + + /* Used for Spansion flashes only. */ + #define SPINOR_OP_BRWR 0x17 /* Bank register write */ +@@ -135,6 +136,7 @@ + + /* Configuration Register bits. */ + #define CR_QUAD_EN_SPAN BIT(1) /* Spansion Quad I/O */ ++#define XCR_DEF_4B_ADDR_MODE BIT(1) /* Winbond 4B mode default */ + + /* Status Register 2 bits. */ + #define SR2_QUAD_EN_BIT7 BIT(7) diff --git a/target/linux/ramips/patches-5.4/0069-awake-rt305x-dwc2-controller.patch b/target/linux/ramips/patches-5.4/0069-awake-rt305x-dwc2-controller.patch new file mode 100644 index 0000000000..0e09e1d4e0 --- /dev/null +++ b/target/linux/ramips/patches-5.4/0069-awake-rt305x-dwc2-controller.patch @@ -0,0 +1,15 @@ +--- a/drivers/usb/dwc2/platform.c ++++ b/drivers/usb/dwc2/platform.c +@@ -406,6 +406,12 @@ static int dwc2_driver_probe(struct plat + if (retval) + return retval; + ++ /* Enable USB port before any regs access */ ++ if (dwc2_readl(hsotg->regs + PCGCTL) & 0x0f) { ++ dwc2_writel(0x00, hsotg->regs + PCGCTL); ++ /* TODO: mdelay(25) here? vendor driver don't use it */ ++ } ++ + retval = dwc2_get_dr_mode(hsotg); + if (retval) + goto error; diff --git a/target/linux/ramips/patches-5.4/0070-weak_reordering.patch b/target/linux/ramips/patches-5.4/0070-weak_reordering.patch new file mode 100644 index 0000000000..52e6641324 --- /dev/null +++ b/target/linux/ramips/patches-5.4/0070-weak_reordering.patch @@ -0,0 +1,10 @@ +--- a/arch/mips/ralink/Kconfig ++++ b/arch/mips/ralink/Kconfig +@@ -58,6 +58,7 @@ choice + select COMMON_CLK + select CLKSRC_MIPS_GIC + select HW_HAS_PCI ++ select WEAK_REORDERING_BEYOND_LLSC + endchoice + + choice diff --git a/target/linux/ramips/patches-5.4/0098-disable_cm.patch b/target/linux/ramips/patches-5.4/0098-disable_cm.patch new file mode 100644 index 0000000000..bc00619dff --- /dev/null +++ b/target/linux/ramips/patches-5.4/0098-disable_cm.patch @@ -0,0 +1,19 @@ +--- a/arch/mips/kernel/mips-cm.c ++++ b/arch/mips/kernel/mips-cm.c +@@ -237,6 +237,7 @@ int mips_cm_probe(void) + + /* disable CM regions */ + write_gcr_reg0_base(CM_GCR_REGn_BASE_BASEADDR); ++ /* + write_gcr_reg0_mask(CM_GCR_REGn_MASK_ADDRMASK); + write_gcr_reg1_base(CM_GCR_REGn_BASE_BASEADDR); + write_gcr_reg1_mask(CM_GCR_REGn_MASK_ADDRMASK); +@@ -244,7 +245,7 @@ int mips_cm_probe(void) + write_gcr_reg2_mask(CM_GCR_REGn_MASK_ADDRMASK); + write_gcr_reg3_base(CM_GCR_REGn_BASE_BASEADDR); + write_gcr_reg3_mask(CM_GCR_REGn_MASK_ADDRMASK); +- ++*/ + /* probe for an L2-only sync region */ + mips_cm_probe_l2sync(); + diff --git a/target/linux/ramips/patches-5.4/0099-pci-mt7620.patch b/target/linux/ramips/patches-5.4/0099-pci-mt7620.patch new file mode 100644 index 0000000000..997fb6a2b3 --- /dev/null +++ b/target/linux/ramips/patches-5.4/0099-pci-mt7620.patch @@ -0,0 +1,10 @@ +--- a/arch/mips/pci/pci-mt7620.c ++++ b/arch/mips/pci/pci-mt7620.c +@@ -33,7 +33,6 @@ + #define RALINK_GPIOMODE 0x60 + + #define PPLL_CFG1 0x9c +-#define PDRV_SW_SET BIT(23) + + #define PPLL_DRV 0xa0 + #define PDRV_SW_SET (1<<31) diff --git a/target/linux/ramips/patches-5.4/0200-linkit_bootstrap.patch b/target/linux/ramips/patches-5.4/0200-linkit_bootstrap.patch new file mode 100644 index 0000000000..cd1462fbcf --- /dev/null +++ b/target/linux/ramips/patches-5.4/0200-linkit_bootstrap.patch @@ -0,0 +1,97 @@ +--- a/drivers/misc/Makefile ++++ b/drivers/misc/Makefile +@@ -56,6 +56,7 @@ obj-$(CONFIG_CXL_BASE) += cxl/ + obj-$(CONFIG_ASPEED_LPC_CTRL) += aspeed-lpc-ctrl.o + obj-$(CONFIG_ASPEED_LPC_SNOOP) += aspeed-lpc-snoop.o + obj-$(CONFIG_PCI_ENDPOINT_TEST) += pci_endpoint_test.o ++obj-$(CONFIG_SOC_MT7620) += linkit.o + + lkdtm-$(CONFIG_LKDTM) += lkdtm_core.o + lkdtm-$(CONFIG_LKDTM) += lkdtm_bugs.o +--- /dev/null ++++ b/drivers/misc/linkit.c +@@ -0,0 +1,84 @@ ++/* ++ * This program is free software; you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License version 2 as ++ * publishhed by the Free Software Foundation. ++ * ++ * Copyright (C) 2015 John Crispin ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++ ++#define LINKIT_LATCH_GPIO 11 ++ ++struct linkit_hw_data { ++ char board[16]; ++ char rev[16]; ++}; ++ ++static void sanify_string(char *s) ++{ ++ int i; ++ ++ for (i = 0; i < 15; i++) ++ if (s[i] <= 0x20) ++ s[i] = '\0'; ++ s[15] = '\0'; ++} ++ ++static int linkit_probe(struct platform_device *pdev) ++{ ++ struct linkit_hw_data hw; ++ struct mtd_info *mtd; ++ size_t retlen; ++ int ret; ++ ++ mtd = get_mtd_device_nm("factory"); ++ if (IS_ERR(mtd)) ++ return PTR_ERR(mtd); ++ ++ ret = mtd_read(mtd, 0x400, sizeof(hw), &retlen, (u_char *) &hw); ++ put_mtd_device(mtd); ++ ++ sanify_string(hw.board); ++ sanify_string(hw.rev); ++ ++ dev_info(&pdev->dev, "Version : %s\n", hw.board); ++ dev_info(&pdev->dev, "Revision : %s\n", hw.rev); ++ ++ if (!strcmp(hw.board, "LINKITS7688")) { ++ dev_info(&pdev->dev, "setting up bootstrap latch\n"); ++ ++ if (devm_gpio_request(&pdev->dev, LINKIT_LATCH_GPIO, "bootstrap")) { ++ dev_err(&pdev->dev, "failed to setup bootstrap gpio\n"); ++ return -1; ++ } ++ gpio_direction_output(LINKIT_LATCH_GPIO, 0); ++ } ++ ++ return 0; ++} ++ ++static const struct of_device_id linkit_match[] = { ++ { .compatible = "mediatek,linkit" }, ++ {}, ++}; ++MODULE_DEVICE_TABLE(of, linkit_match); ++ ++static struct platform_driver linkit_driver = { ++ .probe = linkit_probe, ++ .driver = { ++ .name = "mtk-linkit", ++ .owner = THIS_MODULE, ++ .of_match_table = linkit_match, ++ }, ++}; ++ ++int __init linkit_init(void) ++{ ++ return platform_driver_register(&linkit_driver); ++} ++late_initcall_sync(linkit_init); diff --git a/target/linux/ramips/patches-5.4/100-mt7621-core-detect-hack.patch b/target/linux/ramips/patches-5.4/100-mt7621-core-detect-hack.patch new file mode 100644 index 0000000000..991e19b6df --- /dev/null +++ b/target/linux/ramips/patches-5.4/100-mt7621-core-detect-hack.patch @@ -0,0 +1,61 @@ +There is a variant of MT7621 which contains only one CPU core instead of 2. +This is not reflected in the config register, so the kernel detects more +physical cores, which leads to a hang on SMP bringup. +Add a hack to detect missing cores. + +Signed-off-by: Felix Fietkau + +--- a/arch/mips/kernel/smp-cps.c ++++ b/arch/mips/kernel/smp-cps.c +@@ -47,6 +47,11 @@ static unsigned core_vpe_count(unsigned + return mips_cps_numvps(cluster, core); + } + ++bool __weak plat_cpu_core_present(int core) ++{ ++ return true; ++} ++ + static void __init cps_smp_setup(void) + { + unsigned int nclusters, ncores, nvpes, core_vpes; +@@ -64,6 +69,8 @@ static void __init cps_smp_setup(void) + + ncores = mips_cps_numcores(cl); + for (c = 0; c < ncores; c++) { ++ if (!plat_cpu_core_present(c)) ++ continue; + core_vpes = core_vpe_count(cl, c); + + if (c > 0) +--- a/arch/mips/ralink/mt7621.c ++++ b/arch/mips/ralink/mt7621.c +@@ -15,6 +15,7 @@ + #include + #include + #include ++#include + + #include + +@@ -162,6 +163,20 @@ void __init ralink_of_remap(void) + panic("Failed to remap core resources"); + } + ++bool plat_cpu_core_present(int core) ++{ ++ struct cpulaunch *launch = (struct cpulaunch *)CKSEG0ADDR(CPULAUNCH); ++ ++ if (!core) ++ return true; ++ launch += core * 2; /* 2 VPEs per core */ ++ if (!(launch->flags & LAUNCH_FREADY)) ++ return false; ++ if (launch->flags & (LAUNCH_FGO | LAUNCH_FGONE)) ++ return false; ++ return true; ++} ++ + void prom_soc_init(struct ralink_soc_info *soc_info) + { + void __iomem *sysc = (void __iomem *) KSEG1ADDR(MT7621_SYSC_BASE); diff --git a/target/linux/ramips/patches-5.4/101-mt7621-timer.patch b/target/linux/ramips/patches-5.4/101-mt7621-timer.patch new file mode 100644 index 0000000000..10edafd412 --- /dev/null +++ b/target/linux/ramips/patches-5.4/101-mt7621-timer.patch @@ -0,0 +1,87 @@ +--- a/arch/mips/ralink/mt7621.c ++++ b/arch/mips/ralink/mt7621.c +@@ -9,6 +9,7 @@ + + #include + #include ++#include + + #include + #include +@@ -16,6 +17,7 @@ + #include + #include + #include ++#include + + #include + +@@ -177,6 +179,58 @@ bool plat_cpu_core_present(int core) + return true; + } + ++#define LPS_PREC 8 ++/* ++* Re-calibration lpj(loop-per-jiffy). ++* (derived from kernel/calibrate.c) ++*/ ++static int udelay_recal(void) ++{ ++ unsigned int i, lpj = 0; ++ unsigned long ticks, loopbit; ++ int lps_precision = LPS_PREC; ++ ++ lpj = (1<<12); ++ ++ while ((lpj <<= 1) != 0) { ++ /* wait for "start of" clock tick */ ++ ticks = jiffies; ++ while (ticks == jiffies) ++ /* nothing */; ++ ++ /* Go .. */ ++ ticks = jiffies; ++ __delay(lpj); ++ ticks = jiffies - ticks; ++ if (ticks) ++ break; ++ } ++ ++ /* ++ * Do a binary approximation to get lpj set to ++ * equal one clock (up to lps_precision bits) ++ */ ++ lpj >>= 1; ++ loopbit = lpj; ++ while (lps_precision-- && (loopbit >>= 1)) { ++ lpj |= loopbit; ++ ticks = jiffies; ++ while (ticks == jiffies) ++ /* nothing */; ++ ticks = jiffies; ++ __delay(lpj); ++ if (jiffies != ticks) /* longer than 1 tick */ ++ lpj &= ~loopbit; ++ } ++ printk(KERN_INFO "%d CPUs re-calibrate udelay(lpj = %d)\n", NR_CPUS, lpj); ++ ++ for(i=0; i< NR_CPUS; i++) ++ cpu_data[i].udelay_val = lpj; ++ ++ return 0; ++} ++device_initcall(udelay_recal); ++ + void prom_soc_init(struct ralink_soc_info *soc_info) + { + void __iomem *sysc = (void __iomem *) KSEG1ADDR(MT7621_SYSC_BASE); +--- a/arch/mips/ralink/Kconfig ++++ b/arch/mips/ralink/Kconfig +@@ -59,6 +59,7 @@ choice + select CLKSRC_MIPS_GIC + select HW_HAS_PCI + select WEAK_REORDERING_BEYOND_LLSC ++ select GENERIC_CLOCKEVENTS_BROADCAST + endchoice + + choice diff --git a/target/linux/ramips/patches-5.4/102-mt7621-fix-cpu-clk-add-clkdev.patch b/target/linux/ramips/patches-5.4/102-mt7621-fix-cpu-clk-add-clkdev.patch new file mode 100644 index 0000000000..e647a2f4c8 --- /dev/null +++ b/target/linux/ramips/patches-5.4/102-mt7621-fix-cpu-clk-add-clkdev.patch @@ -0,0 +1,224 @@ +--- a/arch/mips/include/asm/mach-ralink/mt7621.h ++++ b/arch/mips/include/asm/mach-ralink/mt7621.h +@@ -19,6 +19,10 @@ + #define SYSC_REG_CHIP_REV 0x0c + #define SYSC_REG_SYSTEM_CONFIG0 0x10 + #define SYSC_REG_SYSTEM_CONFIG1 0x14 ++#define SYSC_REG_CLKCFG0 0x2c ++#define SYSC_REG_CUR_CLK_STS 0x44 ++ ++#define MEMC_REG_CPU_PLL 0x648 + + #define CHIP_REV_PKG_MASK 0x1 + #define CHIP_REV_PKG_SHIFT 16 +@@ -26,6 +30,22 @@ + #define CHIP_REV_VER_SHIFT 8 + #define CHIP_REV_ECO_MASK 0xf + ++#define XTAL_MODE_SEL_MASK 0x7 ++#define XTAL_MODE_SEL_SHIFT 6 ++ ++#define CPU_CLK_SEL_MASK 0x3 ++#define CPU_CLK_SEL_SHIFT 30 ++ ++#define CUR_CPU_FDIV_MASK 0x1f ++#define CUR_CPU_FDIV_SHIFT 8 ++#define CUR_CPU_FFRAC_MASK 0x1f ++#define CUR_CPU_FFRAC_SHIFT 0 ++ ++#define CPU_PLL_PREDIV_MASK 0x3 ++#define CPU_PLL_PREDIV_SHIFT 12 ++#define CPU_PLL_FBDIV_MASK 0x7f ++#define CPU_PLL_FBDIV_SHIFT 4 ++ + #define MT7621_DRAM_BASE 0x0 + #define MT7621_DDR2_SIZE_MIN 32 + #define MT7621_DDR2_SIZE_MAX 256 +--- a/arch/mips/ralink/mt7621.c ++++ b/arch/mips/ralink/mt7621.c +@@ -10,6 +10,10 @@ + #include + #include + #include ++#include ++#include ++#include ++#include + + #include + #include +@@ -18,16 +22,12 @@ + #include + #include + #include ++#include + + #include + + #include "common.h" + +-#define SYSC_REG_SYSCFG 0x10 +-#define SYSC_REG_CPLL_CLKCFG0 0x2c +-#define SYSC_REG_CUR_CLK_STS 0x44 +-#define CPU_CLK_SEL (BIT(30) | BIT(31)) +- + #define MT7621_GPIO_MODE_UART1 1 + #define MT7621_GPIO_MODE_I2C 2 + #define MT7621_GPIO_MODE_UART3_MASK 0x3 +@@ -113,49 +113,89 @@ static struct rt2880_pmx_group mt7621_pi + { 0 } + }; + ++static struct clk *clks[MT7621_CLK_MAX]; ++static struct clk_onecell_data clk_data = { ++ .clks = clks, ++ .clk_num = ARRAY_SIZE(clks), ++}; ++ + phys_addr_t mips_cpc_default_phys_base(void) + { + panic("Cannot detect cpc address"); + } + +-void __init ralink_clk_init(void) ++static struct clk *__init mt7621_add_sys_clkdev( ++ const char *id, unsigned long rate) + { +- int cpu_fdiv = 0; +- int cpu_ffrac = 0; +- int fbdiv = 0; +- u32 clk_sts, syscfg; +- u8 clk_sel = 0, xtal_mode; +- u32 cpu_clk; ++ struct clk *clk; ++ int err; ++ ++ clk = clk_register_fixed_rate(NULL, id, NULL, 0, rate); ++ if (IS_ERR(clk)) ++ panic("failed to allocate %s clock structure", id); ++ ++ err = clk_register_clkdev(clk, id, NULL); ++ if (err) ++ panic("unable to register %s clock device", id); + +- if ((rt_sysc_r32(SYSC_REG_CPLL_CLKCFG0) & CPU_CLK_SEL) != 0) +- clk_sel = 1; ++ return clk; ++} ++ ++void __init ralink_clk_init(void) ++{ ++ u32 syscfg, xtal_sel, clkcfg, clk_sel, curclk, ffiv, ffrac; ++ u32 pll, prediv, fbdiv; ++ u32 xtal_clk, cpu_clk, bus_clk; ++ const static u32 prediv_tbl[] = {0, 1, 2, 2}; ++ ++ syscfg = rt_sysc_r32(SYSC_REG_SYSTEM_CONFIG0); ++ xtal_sel = (syscfg >> XTAL_MODE_SEL_SHIFT) & XTAL_MODE_SEL_MASK; ++ ++ clkcfg = rt_sysc_r32(SYSC_REG_CLKCFG0); ++ clk_sel = (clkcfg >> CPU_CLK_SEL_SHIFT) & CPU_CLK_SEL_MASK; ++ ++ curclk = rt_sysc_r32(SYSC_REG_CUR_CLK_STS); ++ ffiv = (curclk >> CUR_CPU_FDIV_SHIFT) & CUR_CPU_FDIV_MASK; ++ ffrac = (curclk >> CUR_CPU_FFRAC_SHIFT) & CUR_CPU_FFRAC_MASK; ++ ++ if (xtal_sel <= 2) ++ xtal_clk = 20 * 1000 * 1000; ++ else if (xtal_sel <= 5) ++ xtal_clk = 40 * 1000 * 1000; ++ else ++ xtal_clk = 25 * 1000 * 1000; + + switch (clk_sel) { + case 0: +- clk_sts = rt_sysc_r32(SYSC_REG_CUR_CLK_STS); +- cpu_fdiv = ((clk_sts >> 8) & 0x1F); +- cpu_ffrac = (clk_sts & 0x1F); +- cpu_clk = (500 * cpu_ffrac / cpu_fdiv) * 1000 * 1000; ++ cpu_clk = 500 * 1000 * 1000; + break; +- + case 1: +- fbdiv = ((rt_sysc_r32(0x648) >> 4) & 0x7F) + 1; +- syscfg = rt_sysc_r32(SYSC_REG_SYSCFG); +- xtal_mode = (syscfg >> 6) & 0x7; +- if (xtal_mode >= 6) { +- /* 25Mhz Xtal */ +- cpu_clk = 25 * fbdiv * 1000 * 1000; +- } else if (xtal_mode >= 3) { +- /* 40Mhz Xtal */ +- cpu_clk = 40 * fbdiv * 1000 * 1000; +- } else { +- /* 20Mhz Xtal */ +- cpu_clk = 20 * fbdiv * 1000 * 1000; +- } ++ pll = rt_memc_r32(MEMC_REG_CPU_PLL); ++ fbdiv = (pll >> CPU_PLL_FBDIV_SHIFT) & CPU_PLL_FBDIV_MASK; ++ prediv = (pll >> CPU_PLL_PREDIV_SHIFT) & CPU_PLL_PREDIV_MASK; ++ cpu_clk = ((fbdiv + 1) * xtal_clk) >> prediv_tbl[prediv]; + break; ++ default: ++ cpu_clk = xtal_clk; + } ++ ++ cpu_clk = cpu_clk / ffiv * ffrac; ++ bus_clk = cpu_clk / 4; ++ ++ clks[MT7621_CLK_CPU] = mt7621_add_sys_clkdev("cpu", cpu_clk); ++ clks[MT7621_CLK_BUS] = mt7621_add_sys_clkdev("bus", bus_clk); ++ ++ pr_info("CPU Clock: %dMHz\n", cpu_clk / 1000000); ++ mips_hpt_frequency = cpu_clk / 2; + } + ++static void __init mt7621_clocks_init_dt(struct device_node *np) ++{ ++ of_clk_add_provider(np, of_clk_src_onecell_get, &clk_data); ++} ++ ++CLK_OF_DECLARE(ar7100, "mediatek,mt7621-pll", mt7621_clocks_init_dt); ++ + void __init ralink_of_remap(void) + { + rt_sysc_membase = plat_of_remap_node("mtk,mt7621-sysc"); +--- a/arch/mips/ralink/timer-gic.c ++++ b/arch/mips/ralink/timer-gic.c +@@ -11,14 +11,14 @@ + + #include + #include +-#include ++#include + + #include "common.h" + + void __init plat_time_init(void) + { + ralink_of_remap(); +- ++ ralink_clk_init(); + of_clk_init(NULL); + timer_probe(); + } +--- /dev/null ++++ b/include/dt-bindings/clock/mt7621-clk.h +@@ -0,0 +1,18 @@ ++/* ++ * Copyright (C) 2018 Weijie Gao ++ * ++ * This program is free software; you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License version 2 as ++ * published by the Free Software Foundation. ++ * ++ */ ++ ++#ifndef __DT_BINDINGS_MT7621_CLK_H ++#define __DT_BINDINGS_MT7621_CLK_H ++ ++#define MT7621_CLK_CPU 0 ++#define MT7621_CLK_BUS 1 ++ ++#define MT7621_CLK_MAX 2 ++ ++#endif /* __DT_BINDINGS_MT7621_CLK_H */ diff --git a/target/linux/ramips/patches-5.4/105-mt7621-memory-detect.patch b/target/linux/ramips/patches-5.4/105-mt7621-memory-detect.patch new file mode 100644 index 0000000000..b19b57fd66 --- /dev/null +++ b/target/linux/ramips/patches-5.4/105-mt7621-memory-detect.patch @@ -0,0 +1,125 @@ +From b5a52351a66f3c2a7a207548aa87d78ff2d336c0 Mon Sep 17 00:00:00 2001 +From: Chuanhong Guo +Date: Wed, 10 Jul 2019 00:24:48 +0800 +Subject: [PATCH] MIPS: ralink: mt7621: add memory detection support + +mt7621 has the following memory map: +0x0-0x1c000000: lower 448m memory +0x1c000000-0x2000000: peripheral registers +0x20000000-0x2400000: higher 64m memory + +detect_memory_region in arch/mips/kernel/setup.c only add the first +memory region and isn't suitable for 512m memory detection because +it may accidentally read the memory area for peripheral registers. + +This commit adds memory detection capability for mt7621: +1. add the highmem area when 512m is detected. +2. guard memcmp from accessing peripheral registers: + This only happens when some weird user decided to change + kernel load address to 256m or higher address. Since this + is a quite unusual case, we just skip 512m testing and return + 256m as memory size. + +Signed-off-by: Chuanhong Guo +--- + arch/mips/include/asm/mach-ralink/mt7621.h | 7 ++--- + arch/mips/ralink/mt7621.c | 30 +++++++++++++++++++--- + 2 files changed, 30 insertions(+), 7 deletions(-) + +--- a/arch/mips/include/asm/mach-ralink/mt7621.h ++++ b/arch/mips/include/asm/mach-ralink/mt7621.h +@@ -46,9 +46,10 @@ + #define CPU_PLL_FBDIV_MASK 0x7f + #define CPU_PLL_FBDIV_SHIFT 4 + +-#define MT7621_DRAM_BASE 0x0 +-#define MT7621_DDR2_SIZE_MIN 32 +-#define MT7621_DDR2_SIZE_MAX 256 ++#define MT7621_LOWMEM_BASE 0x0 ++#define MT7621_LOWMEM_MAX_SIZE 0x1C000000 ++#define MT7621_HIGHMEM_BASE 0x20000000 ++#define MT7621_HIGHMEM_SIZE 0x4000000 + + #define MT7621_CHIP_NAME0 0x3637544D + #define MT7621_CHIP_NAME1 0x20203132 +--- a/arch/mips/ralink/mt7621.c ++++ b/arch/mips/ralink/mt7621.c +@@ -15,6 +15,7 @@ + #include + #include + ++#include + #include + #include + #include +@@ -57,6 +58,8 @@ + #define MT7621_GPIO_MODE_SDHCI_SHIFT 18 + #define MT7621_GPIO_MODE_SDHCI_GPIO 1 + ++static void *detect_magic __initdata = detect_memory_region; ++ + static struct rt2880_pmx_func uart1_grp[] = { FUNC("uart1", 0, 1, 2) }; + static struct rt2880_pmx_func i2c_grp[] = { FUNC("i2c", 0, 3, 2) }; + static struct rt2880_pmx_func uart3_grp[] = { +@@ -141,6 +144,28 @@ static struct clk *__init mt7621_add_sys + return clk; + } + ++void __init mt7621_memory_detect(void) ++{ ++ void *dm = &detect_magic; ++ phys_addr_t size; ++ ++ for (size = 32 * SZ_1M; size < 256 * SZ_1M; size <<= 1) { ++ if (!memcmp(dm, dm + size, sizeof(detect_magic))) ++ break; ++ } ++ ++ if ((size == 256 * SZ_1M) && ++ (CPHYSADDR(dm + size) < MT7621_LOWMEM_MAX_SIZE) && ++ memcmp(dm, dm + size, sizeof(detect_magic))) { ++ add_memory_region(MT7621_LOWMEM_BASE, MT7621_LOWMEM_MAX_SIZE, ++ BOOT_MEM_RAM); ++ add_memory_region(MT7621_HIGHMEM_BASE, MT7621_HIGHMEM_SIZE, ++ BOOT_MEM_RAM); ++ } else { ++ add_memory_region(MT7621_LOWMEM_BASE, size, BOOT_MEM_RAM); ++ } ++} ++ + void __init ralink_clk_init(void) + { + u32 syscfg, xtal_sel, clkcfg, clk_sel, curclk, ffiv, ffrac; +@@ -319,10 +344,7 @@ void prom_soc_init(struct ralink_soc_inf + (rev >> CHIP_REV_VER_SHIFT) & CHIP_REV_VER_MASK, + (rev & CHIP_REV_ECO_MASK)); + +- soc_info->mem_size_min = MT7621_DDR2_SIZE_MIN; +- soc_info->mem_size_max = MT7621_DDR2_SIZE_MAX; +- soc_info->mem_base = MT7621_DRAM_BASE; +- ++ soc_info->mem_detect = mt7621_memory_detect; + rt2880_pinmux_data = mt7621_pinmux_data; + + +--- a/arch/mips/ralink/common.h ++++ b/arch/mips/ralink/common.h +@@ -19,6 +19,7 @@ struct ralink_soc_info { + unsigned long mem_size; + unsigned long mem_size_min; + unsigned long mem_size_max; ++ void (*mem_detect)(void); + }; + extern struct ralink_soc_info soc_info; + +--- a/arch/mips/ralink/of.c ++++ b/arch/mips/ralink/of.c +@@ -89,6 +89,8 @@ void __init plat_mem_setup(void) + of_scan_flat_dt(early_init_dt_find_memory, NULL); + if (memory_dtb) + of_scan_flat_dt(early_init_dt_scan_memory, NULL); ++ else if (soc_info.mem_detect) ++ soc_info.mem_detect(); + else if (soc_info.mem_size) + add_memory_region(soc_info.mem_base, soc_info.mem_size * SZ_1M, + BOOT_MEM_RAM); diff --git a/target/linux/ramips/patches-5.4/110-mt7621-perfctr-fix.patch b/target/linux/ramips/patches-5.4/110-mt7621-perfctr-fix.patch new file mode 100644 index 0000000000..4c40e65ab9 --- /dev/null +++ b/target/linux/ramips/patches-5.4/110-mt7621-perfctr-fix.patch @@ -0,0 +1,15 @@ +--- a/arch/mips/ralink/irq-gic.c ++++ b/arch/mips/ralink/irq-gic.c +@@ -15,6 +15,12 @@ + + int get_c0_perfcount_int(void) + { ++ /* ++ * Performance counter events are routed through GIC. ++ * Prevent them from firing on CPU IRQ7 as well ++ */ ++ clear_c0_status(IE_SW0 << 7); ++ + return gic_get_c0_perfcount_int(); + } + EXPORT_SYMBOL_GPL(get_c0_perfcount_int); diff --git a/target/linux/ramips/patches-5.4/300-mt7620-export-chip-version-and-pkg.patch b/target/linux/ramips/patches-5.4/300-mt7620-export-chip-version-and-pkg.patch new file mode 100644 index 0000000000..0cb1fede30 --- /dev/null +++ b/target/linux/ramips/patches-5.4/300-mt7620-export-chip-version-and-pkg.patch @@ -0,0 +1,19 @@ +--- a/arch/mips/include/asm/mach-ralink/mt7620.h ++++ b/arch/mips/include/asm/mach-ralink/mt7620.h +@@ -137,4 +137,16 @@ static inline int mt7620_get_eco(void) + return rt_sysc_r32(SYSC_REG_CHIP_REV) & CHIP_REV_ECO_MASK; + } + ++static inline int mt7620_get_chipver(void) ++{ ++ return (rt_sysc_r32(SYSC_REG_CHIP_REV) >> CHIP_REV_VER_SHIFT) & ++ CHIP_REV_VER_MASK; ++} ++ ++static inline int mt7620_get_pkg(void) ++{ ++ return (rt_sysc_r32(SYSC_REG_CHIP_REV) >> CHIP_REV_PKG_SHIFT) & ++ CHIP_REV_PKG_MASK; ++} ++ + #endif diff --git a/target/linux/ramips/patches-5.4/302-spi-nor-add-gd25q512.patch b/target/linux/ramips/patches-5.4/302-spi-nor-add-gd25q512.patch new file mode 100644 index 0000000000..0a3a65d70a --- /dev/null +++ b/target/linux/ramips/patches-5.4/302-spi-nor-add-gd25q512.patch @@ -0,0 +1,14 @@ +--- a/drivers/mtd/spi-nor/spi-nor.c ++++ b/drivers/mtd/spi-nor/spi-nor.c +@@ -1066,6 +1066,11 @@ static const struct flash_info spi_nor_i + SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | + SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB) + }, ++ { ++ "gd25q512", INFO(0xc84020, 0, 64 * 1024, 1024, ++ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | ++ SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB | SPI_NOR_4B_OPCODES) ++ }, + + /* Intel/Numonyx -- xxxs33b */ + { "160s33b", INFO(0x898911, 0, 64 * 1024, 32, 0) }, diff --git a/target/linux/ramips/patches-5.4/304-spi-nor-enable-4B-opcodes-for-mx25l25635f.patch b/target/linux/ramips/patches-5.4/304-spi-nor-enable-4B-opcodes-for-mx25l25635f.patch new file mode 100644 index 0000000000..8b59a106e1 --- /dev/null +++ b/target/linux/ramips/patches-5.4/304-spi-nor-enable-4B-opcodes-for-mx25l25635f.patch @@ -0,0 +1,72 @@ +This hack can be dropped after the next stable release from +v5.x-tree. + +The problem was fixed upstream by + +commit 2bffa65da43e ("mtd: spi-nor: Add a post BFPT fixup for MX25L25635E") + +For reference see: + + +--- a/drivers/mtd/spi-nor/spi-nor.c ++++ b/drivers/mtd/spi-nor/spi-nor.c +@@ -1103,6 +1103,7 @@ static const struct flash_info spi_nor_i + { "mx25l12805d", INFO(0xc22018, 0, 64 * 1024, 256, 0) }, + { "mx25l12855e", INFO(0xc22618, 0, 64 * 1024, 256, 0) }, + { "mx25l25635e", INFO(0xc22019, 0, 64 * 1024, 512, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) }, ++ { "mx25l25635f", INFO(0xc22019, 0, 64 * 1024, 512, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) }, + { "mx25u25635f", INFO(0xc22539, 0, 64 * 1024, 512, SECT_4K | SPI_NOR_4B_OPCODES) }, + { "mx25l25655e", INFO(0xc22619, 0, 64 * 1024, 512, 0) }, + { "mx66l51235l", INFO(0xc2201a, 0, 64 * 1024, 1024, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) }, +@@ -1275,11 +1276,12 @@ static const struct flash_info spi_nor_i + { }, + }; + +-static const struct flash_info *spi_nor_read_id(struct spi_nor *nor) ++static const struct flash_info *spi_nor_read_id(struct spi_nor *nor, ++ const char *name) + { + int tmp; + u8 id[SPI_NOR_MAX_ID_LEN]; +- const struct flash_info *info; ++ const struct flash_info *info, *first_match = NULL; + + tmp = nor->read_reg(nor, SPINOR_OP_RDID, id, SPI_NOR_MAX_ID_LEN); + if (tmp < 0) { +@@ -1290,10 +1292,16 @@ static const struct flash_info *spi_nor_ + for (tmp = 0; tmp < ARRAY_SIZE(spi_nor_ids) - 1; tmp++) { + info = &spi_nor_ids[tmp]; + if (info->id_len) { +- if (!memcmp(info->id, id, info->id_len)) +- return &spi_nor_ids[tmp]; ++ if (!memcmp(info->id, id, info->id_len)) { ++ if (!name || !strcmp(name, info->name)) ++ return info; ++ if (!first_match) ++ first_match = info; ++ } + } + } ++ if (first_match) ++ return first_match; + dev_err(nor->dev, "unrecognized JEDEC id bytes: %02x, %02x, %02x\n", + id[0], id[1], id[2]); + return ERR_PTR(-ENODEV); +@@ -2773,7 +2781,7 @@ int spi_nor_scan(struct spi_nor *nor, co + info = spi_nor_match_id(name); + /* Try to auto-detect if chip name wasn't specified or not found */ + if (!info) +- info = spi_nor_read_id(nor); ++ info = spi_nor_read_id(nor, NULL); + if (IS_ERR_OR_NULL(info)) + return -ENOENT; + +@@ -2784,7 +2792,7 @@ int spi_nor_scan(struct spi_nor *nor, co + if (name && info->id_len) { + const struct flash_info *jinfo; + +- jinfo = spi_nor_read_id(nor); ++ jinfo = spi_nor_read_id(nor, name); + if (IS_ERR(jinfo)) { + return PTR_ERR(jinfo); + } else if (jinfo != info) { diff --git a/target/linux/ramips/patches-5.4/999-fix-pci-init-mt7620.patch b/target/linux/ramips/patches-5.4/999-fix-pci-init-mt7620.patch new file mode 100644 index 0000000000..3310a6bdba --- /dev/null +++ b/target/linux/ramips/patches-5.4/999-fix-pci-init-mt7620.patch @@ -0,0 +1,21 @@ +--- a/arch/mips/pci/pci-mt7620.c ++++ b/arch/mips/pci/pci-mt7620.c +@@ -35,6 +35,7 @@ + #define PPLL_CFG1 0x9c + + #define PPLL_DRV 0xa0 ++#define PPLL_LD (1<<23) + #define PDRV_SW_SET (1<<31) + #define LC_CKDRVPD (1<<19) + #define LC_CKDRVOHZ (1<<18) +@@ -242,8 +243,8 @@ static int mt7620_pci_hw_init(struct pla + rt_sysc_m32(0, RALINK_PCIE0_CLK_EN, RALINK_CLKCFG1); + mdelay(100); + +- if (!(rt_sysc_r32(PPLL_CFG1) & PDRV_SW_SET)) { +- dev_err(&pdev->dev, "MT7620 PPLL unlock\n"); ++ if (!(rt_sysc_r32(PPLL_CFG1) & PPLL_LD)) { ++ dev_err(&pdev->dev, "MT7620 PPLL is unlocked, aborting init\n"); + reset_control_assert(rstpcie0); + rt_sysc_m32(RALINK_PCIE0_CLK_EN, 0, RALINK_CLKCFG1); + return -1; -- cgit v1.2.3