From fd82ffec00ad6edc094a68778059329c8105fe21 Mon Sep 17 00:00:00 2001 From: John Crispin Date: Thu, 12 Mar 2015 10:06:42 +0000 Subject: ar71xx: Hornet UB GPIO WPS/Reset This problem has existed at least since Attitude Adjustment and is also present in trunk. Basically on the Hornet-UB board the functionality of RESET and WPS have "switched places". There are two tickets about the issue at dev.openwrt.org, The solution suggested on them both is incomplete though and introduces the following proglem: Patching as suggested on #14136/#15282 will result in a situation where simply pressing the RESET button on the bottom will cause FACTORY RESET to be run. This is due to GPIO high/low state being incorrect as a result of the above change and virtually the RESET button is in the pressed-down state the entire time. When it is then physically pressed, that causes the opposite, release, to be triggered and since to the board it seemed that the button was pressed long before it was released, the FACTORY RESET results. The attached patch works as expected. I have verified both the incorrect functionality as well as after fixing the issue as described in the patch and flashing the resulting firmware to a Hornet-UB board. Signed-off-by: Janne Cederberg SVN-Revision: 44692 --- target/linux/ar71xx/files/arch/mips/ath79/mach-hornet-ub.c | 10 +++++----- 1 file changed, 5 insertions(+), 5 deletions(-) (limited to 'target/linux') diff --git a/target/linux/ar71xx/files/arch/mips/ath79/mach-hornet-ub.c b/target/linux/ar71xx/files/arch/mips/ath79/mach-hornet-ub.c index 22b1e0919d..b36c5115d6 100644 --- a/target/linux/ar71xx/files/arch/mips/ath79/mach-hornet-ub.c +++ b/target/linux/ar71xx/files/arch/mips/ath79/mach-hornet-ub.c @@ -28,8 +28,8 @@ #define HORNET_UB_GPIO_LED_WAN 17 #define HORNET_UB_GPIO_LED_WPS 27 -#define HORNET_UB_GPIO_BTN_RESET 11 -#define HORNET_UB_GPIO_BTN_WPS 12 +#define HORNET_UB_GPIO_BTN_RESET 12 +#define HORNET_UB_GPIO_BTN_WPS 11 #define HORNET_UB_GPIO_USB_POWER 26 @@ -64,7 +64,7 @@ static struct gpio_led hornet_ub_leds_gpio[] __initdata = { { .name = "alfa:blue:wps", .gpio = HORNET_UB_GPIO_LED_WPS, - .active_low = 1, + .active_low = 0, }, }; @@ -75,7 +75,7 @@ static struct gpio_keys_button hornet_ub_gpio_keys[] __initdata = { .code = KEY_WPS_BUTTON, .debounce_interval = HORNET_UB_KEYS_DEBOUNCE_INTERVAL, .gpio = HORNET_UB_GPIO_BTN_WPS, - .active_low = 1, + .active_low = 0, }, { .desc = "Reset button", @@ -83,7 +83,7 @@ static struct gpio_keys_button hornet_ub_gpio_keys[] __initdata = { .code = KEY_RESTART, .debounce_interval = HORNET_UB_KEYS_DEBOUNCE_INTERVAL, .gpio = HORNET_UB_GPIO_BTN_RESET, - .active_low = 0, + .active_low = 1, } }; -- cgit v1.2.3