From a9ac1dd46a4fd11880be80227e1eb102e3c61dd8 Mon Sep 17 00:00:00 2001
From: Andre Heider <a.heider@gmail.com>
Date: Fri, 4 Sep 2020 15:38:58 +0200
Subject: [PATCH] arm64: dts: armada-3720-espressobin: split common parts
to .dtsi
Move most of the dts to the new common armada-3720-espressobin.dtsi
file, just like Linux, but keep the current, downstream based, version.
The dts itself is imported from Linux.
Signed-off-by: Andre Heider <a.heider@gmail.com>
---
arch/arm/dts/armada-3720-espressobin.dts | 164 +--------------------
arch/arm/dts/armada-3720-espressobin.dtsi | 167 ++++++++++++++++++++++
2 files changed, 174 insertions(+), 157 deletions(-)
create mode 100644 arch/arm/dts/armada-3720-espressobin.dtsi
--- a/arch/arm/dts/armada-3720-espressobin.dts
+++ b/arch/arm/dts/armada-3720-espressobin.dts
@@ -1,170 +1,20 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
- * Device Tree file for Marvell Armada 3720 community board
- * (ESPRESSOBin)
+ * Device Tree file for Globalscale Marvell ESPRESSOBin Board
* Copyright (C) 2016 Marvell
*
- * Gregory CLEMENT <gregory.clement@free-electrons.com>
- * Konstantin Porotchkin <kostap@marvell.com>
+ * Romain Perier <romain.perier@free-electrons.com>
*
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This file is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of the
- * License, or (at your option) any later version.
- *
- * This file is distributed in the hope that it will be useful
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
+ */
+/*
+ * Schematic available at http://espressobin.net/wp-content/uploads/2017/08/ESPRESSObin_V5_Schematics.pdf
*/
/dts-v1/;
-#include "armada-372x.dtsi"
+#include "armada-3720-espressobin.dtsi"
/ {
model = "Globalscale Marvell ESPRESSOBin Board";
compatible = "globalscale,espressobin", "marvell,armada3720", "marvell,armada3710";
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-
- aliases {
- ethernet0 = ð0;
- i2c0 = &i2c0;
- spi0 = &spi0;
- };
-
- memory {
- device_type = "memory";
- reg = <0x00000000 0x00000000 0x00000000 0x20000000>;
- };
-
- vcc_sd_reg0: regulator@0 {
- compatible = "regulator-gpio";
- regulator-name = "vcc_sd0";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- regulator-type = "voltage";
- states = <1800000 0x1
- 3300000 0x0>;
- gpios = <&gpionb 4 GPIO_ACTIVE_HIGH>;
- };
-};
-
-&comphy {
- max-lanes = <3>;
- phy0 {
- phy-type = <PHY_TYPE_USB3_HOST0>;
- phy-speed = <PHY_SPEED_5G>;
- };
-
- phy1 {
- phy-type = <PHY_TYPE_PEX0>;
- phy-speed = <PHY_SPEED_2_5G>;
- };
-
- phy2 {
- phy-type = <PHY_TYPE_SATA0>;
- phy-speed = <PHY_SPEED_5G>;
- };
-};
-
-ð0 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&rgmii_pins>, <&smi_pins>;
- phy-mode = "rgmii";
- phy_addr = <0x1>;
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
-};
-
-&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins>;
- status = "okay";
-};
-
-/* CON3 */
-&sata {
- status = "okay";
-};
-
-&sdhci0 {
- pinctrl-names = "default";
- pinctrl-0 = <&sdio_pins>;
- bus-width = <4>;
- cd-gpios = <&gpionb 3 GPIO_ACTIVE_LOW>;
- vqmmc-supply = <&vcc_sd_reg0>;
- status = "okay";
-};
-
-&spi0 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&spi_quad_pins>;
-
- spi-flash@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "st,m25p128", "jedec,spi-nor";
- reg = <0>; /* Chip select 0 */
- spi-max-frequency = <50000000>;
- m25p,fast-read;
- };
-};
-
-/* Exported on the micro USB connector CON32 through an FTDI */
-&uart0 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart1_pins>;
- status = "okay";
-};
-
-/* CON29 */
-&usb2 {
- status = "okay";
-};
-
-/* CON31 */
-&usb3 {
- status = "okay";
-};
-
-&pcie0 {
- pinctrl-names = "default";
- pinctrl-0 = <&pcie_pins>;
- reset-gpios = <&gpiosb 3 GPIO_ACTIVE_LOW>;
- status = "okay";
};
--- /dev/null
+++ b/arch/arm/dts/armada-3720-espressobin.dtsi
@@ -0,0 +1,167 @@
+/*
+ * Device Tree file for Marvell Armada 3720 community board
+ * (ESPRESSOBin)
+ * Copyright (C) 2016 Marvell
+ *
+ * Gregory CLEMENT <gregory.clement@free-electrons.com>
+ * Konstantin Porotchkin <kostap@marvell.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "armada-372x.dtsi"
+
+/ {
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ aliases {
+ ethernet0 = ð0;
+ i2c0 = &i2c0;
+ spi0 = &spi0;
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x00000000 0x00000000 0x20000000>;
+ };
+
+ vcc_sd_reg0: regulator@0 {
+ compatible = "regulator-gpio";
+ regulator-name = "vcc_sd0";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-type = "voltage";
+ states = <1800000 0x1
+ 3300000 0x0>;
+ gpios = <&gpionb 4 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&comphy {
+ max-lanes = <3>;
+ phy0 {
+ phy-type = <PHY_TYPE_USB3_HOST0>;
+ phy-speed = <PHY_SPEED_5G>;
+ };
+
+ phy1 {
+ phy-type = <PHY_TYPE_PEX0>;
+ phy-speed = <PHY_SPEED_2_5G>;
+ };
+
+ phy2 {
+ phy-type = <PHY_TYPE_SATA0>;
+ phy-speed = <PHY_SPEED_5G>;
+ };
+};
+
+ð0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&rgmii_pins>, <&smi_pins>;
+ phy-mode = "rgmii";
+ phy_addr = <0x1>;
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins>;
+ status = "okay";
+};
+
+/* CON3 */
+&sata {
+ status = "okay";
+};
+
+&sdhci0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdio_pins>;
+ bus-width = <4>;
+ cd-gpios = <&gpionb 3 GPIO_ACTIVE_LOW>;
+ vqmmc-supply = <&vcc_sd_reg0>;
+ status = "okay";
+};
+
+&spi0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi_quad_pins>;
+
+ spi-flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "st,m25p128", "jedec,spi-nor";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <50000000>;
+ m25p,fast-read;
+ };
+};
+
+/* Exported on the micro USB connector CON32 through an FTDI */
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "okay";
+};
+
+/* CON29 */
+&usb2 {
+ status = "okay";
+};
+
+/* CON31 */
+&usb3 {
+ status = "okay";
+};
+
+&pcie0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie_pins>;
+ reset-gpios = <&gpiosb 3 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};