diff options
Diffstat (limited to 'Sensor Watch Starter Project/config/hpl_adc_config.h')
-rw-r--r-- | Sensor Watch Starter Project/config/hpl_adc_config.h | 305 |
1 files changed, 305 insertions, 0 deletions
diff --git a/Sensor Watch Starter Project/config/hpl_adc_config.h b/Sensor Watch Starter Project/config/hpl_adc_config.h new file mode 100644 index 00000000..e15dc52f --- /dev/null +++ b/Sensor Watch Starter Project/config/hpl_adc_config.h @@ -0,0 +1,305 @@ +/* Auto-generated config file hpl_adc_config.h */ +#ifndef HPL_ADC_CONFIG_H +#define HPL_ADC_CONFIG_H + +// <<< Use Configuration Wizard in Context Menu >>> + +#ifndef CONF_ADC_0_ENABLE +#define CONF_ADC_0_ENABLE 1 +#endif + +// <h> Basic Configuration + +// <o> Conversion Result Resolution +// <0x0=>12-bit +// <0x1=>16-bit (averaging must be enabled) +// <0x2=>10-bit +// <0x3=>8-bit +// <i> Defines the bit resolution for the ADC sample values (RESSEL) +// <id> adc_resolution +#ifndef CONF_ADC_0_RESSEL +#define CONF_ADC_0_RESSEL 0x0 +#endif + +// <o> Reference Selection +// <0x0=>Internal bandgap reference +// <0x1=>1/1.6 VDDANA +// <0x2=>1/2 VDDANA (only for VDDANA > 2.0V) +// <0x3=>External reference A +// <0x4=>External reference B +// <0x5=>VDDANA +// <i> Select the reference for the ADC (REFSEL) +// <id> adc_reference +#ifndef CONF_ADC_0_REFSEL +#define CONF_ADC_0_REFSEL 0x0 +#endif + +// <o> Prescaler configuration +// <0x0=>Peripheral clock divided by 2 +// <0x1=>Peripheral clock divided by 4 +// <0x2=>Peripheral clock divided by 8 +// <0x3=>Peripheral clock divided by 16 +// <0x4=>Peripheral clock divided by 32 +// <0x5=>Peripheral clock divided by 64 +// <0x6=>Peripheral clock divided by 128 +// <0x7=>Peripheral clock divided by 256 +// <i> These bits define the ADC clock relative to the peripheral clock (PRESCALER) +// <id> adc_prescaler +#ifndef CONF_ADC_0_PRESCALER +#define CONF_ADC_0_PRESCALER 0x0 +#endif + +// <q> Free Running Mode +// <i> When enabled, the ADC is in free running mode and a new conversion will be initiated when a previous conversion completes. (FREERUN) +// <id> adc_freerunning_mode +#ifndef CONF_ADC_0_FREERUN +#define CONF_ADC_0_FREERUN 0 +#endif + +// <q> Differential Mode +// <i> In differential mode, the voltage difference between the MUXPOS and MUXNEG inputs will be converted by the ADC. (DIFFMODE) +// <id> adc_differential_mode +#ifndef CONF_ADC_0_DIFFMODE +#define CONF_ADC_0_DIFFMODE 0 +#endif + +// <o> Positive Mux Input Selection +// <0x00=>ADC AIN0 pin +// <0x01=>ADC AIN1 pin +// <0x02=>ADC AIN2 pin +// <0x03=>ADC AIN3 pin +// <0x04=>ADC AIN4 pin +// <0x05=>ADC AIN5 pin +// <0x06=>ADC AIN6 pin +// <0x07=>ADC AIN7 pin +// <0x08=>ADC AIN8 pin +// <0x09=>ADC AIN9 pin +// <0x0A=>ADC AIN10 pin +// <0x0B=>ADC AIN11 pin +// <0x0C=>ADC AIN12 pin +// <0x0D=>ADC AIN13 pin +// <0x0E=>ADC AIN14 pin +// <0x0F=>ADC AIN15 pin +// <0x10=>ADC AIN16 pin +// <0x11=>ADC AIN17 pin +// <0x12=>ADC AIN18 pin +// <0x13=>ADC AIN19 pin +// <0x18=>Temperature reference +// <0x19=>Bandgap voltage +// <0x1A=>1/4 scaled core supply +// <0x1B=>1/4 scaled I/O supply +// <0x1D=>1/4 Scaled VBAT Supply +// <0x1E=>CTAT Output +// <i> These bits define the Mux selection for the positive ADC input. (MUXPOS) +// <id> adc_pinmux_positive +#ifndef CONF_ADC_0_MUXPOS +#define CONF_ADC_0_MUXPOS 0x0 +#endif + +// <o> Negative Mux Input Selection +// <0x00=>ADC AIN0 pin +// <0x01=>ADC AIN1 pin +// <0x02=>ADC AIN2 pin +// <0x03=>ADC AIN3 pin +// <0x04=>ADC AIN4 pin +// <0x05=>ADC AIN5 pin +// <0x06=>ADC AIN6 pin +// <0x07=>ADC AIN7 pin +// <0x18=>Internal ground +// <i> These bits define the Mux selection for the negative ADC input. (MUXNEG) +// <id> adc_pinmux_negative +#ifndef CONF_ADC_0_MUXNEG +#define CONF_ADC_0_MUXNEG 0x0 +#endif + +// </h> + +// <e> Advanced Configuration +// <id> adc_advanced_settings +#ifndef CONF_ADC_0_ADVANCED +#define CONF_ADC_0_ADVANCED 0 +#endif + +// <q> Run in standby +// <i> Indicates whether the ADC will continue running in standby sleep mode or not (RUNSTDBY) +// <id> adc_arch_runstdby +#ifndef CONF_ADC_0_RUNSTDBY +#define CONF_ADC_0_RUNSTDBY 0 +#endif + +// <q>Debug Run +// <i> If enabled, the ADC is running if the CPU is halted by an external debugger. (DBGRUN) +// <id> adc_arch_dbgrun +#ifndef CONF_ADC_0_DBGRUN +#define CONF_ADC_0_DBGRUN 0 +#endif + +// <q> On Demand Control +// <i> Will keep the ADC peripheral running if requested by other peripherals (ONDEMAND) +// <id> adc_arch_ondemand +#ifndef CONF_ADC_0_ONDEMAND +#define CONF_ADC_0_ONDEMAND 0 +#endif + +// <q> Left-Adjusted Result +// <i> When enabled, the ADC conversion result is left-adjusted in the RESULT register. The high byte of the 12-bit result will be present in the upper part of the result register. (LEFTADJ) +// <id> adc_arch_leftadj +#ifndef CONF_ADC_0_LEFTADJ +#define CONF_ADC_0_LEFTADJ 0 +#endif + +// <q> Reference Buffer Offset Compensation Enable +// <i> The accuracy of the gain stage can be increased by enabling the reference buffer offset compensation. This will decrease the input impedance and thus increase the start-up time of the reference. (REFCOMP) +// <id> adc_arch_refcomp +#ifndef CONF_ADC_0_REFCOMP +#define CONF_ADC_0_REFCOMP 0 +#endif + +// <q>Comparator Offset Compensation Enable +// <i> This bit indicates whether the Comparator Offset Compensation is enabled or not (OFFCOMP) +// <id> adc_arch_offcomp +#ifndef CONF_ADC_0_OFFCOMP +#define CONF_ADC_0_OFFCOMP 0 +#endif + +// <q> Digital Correction Logic Enabled +// <i> When enabled, the ADC conversion result in the RESULT register is then corrected for gain and offset based on the values in the GAINCAL and OFFSETCAL registers. (CORREN) +// <id> adc_arch_corren +#ifndef CONF_ADC_0_CORREN +#define CONF_ADC_0_CORREN 0 +#endif + +// <o> Offset Correction Value <0-4095> +// <i> If the digital correction logic is enabled (CTRLB.CORREN = 1), these bits define how the ADC conversion result is compensated for offset error before being written to the Result register. (OFFSETCORR) +// <id> adc_arch_offsetcorr +#ifndef CONF_ADC_0_OFFSETCORR +#define CONF_ADC_0_OFFSETCORR 0 +#endif + +// <o> Gain Correction Value <0-4095> +// <i> If the digital correction logic is enabled (CTRLB.CORREN = 1), these bits define how the ADC conversion result is compensated for gain error before being written to the result register. (GAINCORR) +// <id> adc_arch_gaincorr +#ifndef CONF_ADC_0_GAINCORR +#define CONF_ADC_0_GAINCORR 0 +#endif + +// <o> Adjusting Result / Division Coefficient <0-7> +// <i> These bits define the division coefficient in 2n steps. (ADJRES) +// <id> adc_arch_adjres +#ifndef CONF_ADC_0_ADJRES +#define CONF_ADC_0_ADJRES 0x0 +#endif + +// <o.0..10> Number of Samples to be Collected +// <0x0=>1 sample +// <0x1=>2 samples +// <0x2=>4 samples +// <0x3=>8 samples +// <0x4=>16 samples +// <0x5=>32 samples +// <0x6=>64 samples +// <0x7=>128 samples +// <0x8=>256 samples +// <0x9=>512 samples +// <0xA=>1024 samples +// <i> Define how many samples should be added together.The result will be available in the Result register (SAMPLENUM) +// <id> adc_arch_samplenum +#ifndef CONF_ADC_0_SAMPLENUM +#define CONF_ADC_0_SAMPLENUM 0x0 +#endif + +// <o> Sampling Time Length <0-63> +// <i> These bits control the ADC sampling time in number of CLK_ADC cycles, depending of the prescaler value, thus controlling the ADC input impedance. (SAMPLEN) +// <id> adc_arch_samplen +#ifndef CONF_ADC_0_SAMPLEN +#define CONF_ADC_0_SAMPLEN 0 +#endif + +// <o> Window Monitor Mode +// <0x0=>No window mode +// <0x1=>Mode 1: RESULT above lower threshold +// <0x2=>Mode 2: RESULT beneath upper threshold +// <0x3=>Mode 3: RESULT inside lower and upper threshold +// <0x4=>Mode 4: RESULT outside lower and upper threshold +// <i> These bits enable and define the window monitor mode. (WINMODE) +// <id> adc_arch_winmode +#ifndef CONF_ADC_0_WINMODE +#define CONF_ADC_0_WINMODE 0x0 +#endif + +// <o> Window Monitor Lower Threshold <0-65535> +// <i> If the window monitor is enabled, these bits define the lower threshold value. (WINLT) +// <id> adc_arch_winlt +#ifndef CONF_ADC_0_WINLT +#define CONF_ADC_0_WINLT 0 +#endif + +// <o> Window Monitor Upper Threshold <0-65535> +// <i> If the window monitor is enabled, these bits define the lower threshold value. (WINUT) +// <id> adc_arch_winut +#ifndef CONF_ADC_0_WINUT +#define CONF_ADC_0_WINUT 0 +#endif + +// <o> Bitmask for positive input sequence <0-4294967295> +// <i> Use this parameter to input the bitmask for positive input sequence control (refer to datasheet for the device). +// <id> adc_arch_seqen +#ifndef CONF_ADC_0_SEQEN +#define CONF_ADC_0_SEQEN 0x0 +#endif + +// </e> + +// <e> Event Control +// <id> adc_arch_event_settings +#ifndef CONF_ADC_0_EVENT_CONTROL +#define CONF_ADC_0_EVENT_CONTROL 0 +#endif + +// <q> Window Monitor Event Out +// <i> Enables event output on window event (WINMONEO) +// <id> adc_arch_winmoneo +#ifndef CONF_ADC_0_WINMONEO +#define CONF_ADC_0_WINMONEO 0 +#endif + +// <q> Result Ready Event Out +// <i> Enables event output on result ready event (RESRDEO) +// <id> adc_arch_resrdyeo +#ifndef CONF_ADC_0_RESRDYEO +#define CONF_ADC_0_RESRDYEO 0 +#endif + +// <q> Invert flush Event Signal +// <i> Invert the flush event input signal (FLUSHINV) +// <id> adc_arch_flushinv +#ifndef CONF_ADC_0_FLUSHINV +#define CONF_ADC_0_FLUSHINV 0 +#endif + +// <q> Trigger Flush On Event +// <i> Trigger an ADC pipeline flush on event (FLUSHEI) +// <id> adc_arch_flushei +#ifndef CONF_ADC_0_FLUSHEI +#define CONF_ADC_0_FLUSHEI 0 +#endif + +// <q> Invert Start Conversion Event Signal +// <i> Invert the start conversion event input signal (STARTINV) +// <id> adc_arch_startinv +#ifndef CONF_ADC_0_STARTINV +#define CONF_ADC_0_STARTINV 0 +#endif + +// <q> Trigger Conversion On Event +// <i> Trigger a conversion on event. (STARTEI) +// <id> adc_arch_startei +#ifndef CONF_ADC_0_STARTEI +#define CONF_ADC_0_STARTEI 0 +#endif + +// </e> + +// <<< end of configuration section >>> + +#endif // HPL_ADC_CONFIG_H |