diff options
Diffstat (limited to 'Sensor Watch Starter Project/config/hpl_rtc_config.h')
-rw-r--r-- | Sensor Watch Starter Project/config/hpl_rtc_config.h | 318 |
1 files changed, 318 insertions, 0 deletions
diff --git a/Sensor Watch Starter Project/config/hpl_rtc_config.h b/Sensor Watch Starter Project/config/hpl_rtc_config.h new file mode 100644 index 00000000..9085ca37 --- /dev/null +++ b/Sensor Watch Starter Project/config/hpl_rtc_config.h @@ -0,0 +1,318 @@ +/* Auto-generated config file hpl_rtc_config.h */ +#ifndef HPL_RTC_CONFIG_H +#define HPL_RTC_CONFIG_H + +// <<< Use Configuration Wizard in Context Menu >>> + +// <h> Basic settings + +#ifndef CONF_RTC_ENABLE +#define CONF_RTC_ENABLE 1 +#endif + +// <q> Force reset RTC on initialization +// <i> Force RTC to reset on initialization. +// <i> Note that the previous power down data in RTC is lost if it's enabled. +// <id> rtc_arch_init_reset +#ifndef CONF_RTC_INIT_RESET +#define CONF_RTC_INIT_RESET 0 +#endif + +// <o> Prescaler configuration +// <0x0=>OFF(Peripheral clock divided by 1) +// <0x1=>Peripheral clock divided by 1 +// <0x2=>Peripheral clock divided by 2 +// <0x3=>Peripheral clock divided by 4 +// <0x4=>Peripheral clock divided by 8 +// <0x5=>Peripheral clock divided by 16 +// <0x6=>Peripheral clock divided by 32 +// <0x7=>Peripheral clock divided by 64 +// <0x8=>Peripheral clock divided by 128 +// <0x9=>Peripheral clock divided by 256 +// <0xA=>Peripheral clock divided by 512 +// <0xB=>Peripheral clock divided by 1024 +// <i> These bits define the RTC clock relative to the peripheral clock +// <id> rtc_arch_prescaler +#ifndef CONF_RTC_PRESCALER + +#define CONF_RTC_PRESCALER 0xb + +#endif + +#ifndef CONF_RTC_COMP_VAL + +#define CONF_RTC_COMP_VAL 0 + +#endif + +// <e> RTC Tamper Input 0 settings +// <id> tamper_input_0_settings +#ifndef CONF_TAMPER_INPUT_0_SETTINGS +#define CONF_TAMPER_INPUT_0_SETTINGS 0 +#endif + +// <q> Tamper Level Settings +// <i> Indicates Tamper input 0 level +// <id> tamper_level_0 +#ifndef CONF_RTC_TAMP_LVL_0 +#define CONF_RTC_TAMP_LVL_0 0 +#endif + +// <o> RTC Tamper Input Action +// <0x0=>OFF(Disabled) +// <0x1=>Wake and Set Tamper Flag +// <0x2=>Capture Timestamp and Set Tamper Flag +// <0x3=>Active Layer Mode.IN and OUT pin is used.Timestamp is also captured. +// <i> These bits define the RTC Tamper Input Action to be performed +// <id> rtc_tamper_input_action_0 +#ifndef CONF_RTC_TAMPER_INACT_0 +#define CONF_RTC_TAMPER_INACT_0 0 +#endif + +// <q> Debounce Enable for Tamper Input +// <i> Indicates Debounce should be enabled for Tamper input 0 +// <id> tamper_debounce_enable_0 +#ifndef CONF_RTC_TAMP_DEBNC_0 +#define CONF_RTC_TAMP_DEBNC_0 0 +#endif + +// </e> + +// <e> RTC Tamper Input 1 settings +// <id> tamper_input_1_settings +#ifndef CONF_TAMPER_INPUT_1_SETTINGS +#define CONF_TAMPER_INPUT_1_SETTINGS 0 +#endif + +// <q> Tamper Level Settings +// <i> Indicates Tamper input 1 level +// <id> tamper_level_1 +#ifndef CONF_RTC_TAMP_LVL_1 +#define CONF_RTC_TAMP_LVL_1 0 +#endif + +// <o> RTC Tamper Input Action +// <0x0=>OFF(Disabled) +// <0x1=>Wake and Set Tamper Flag +// <0x2=>Capture Timestamp and Set Tamper Flag +// <0x3=>Active Layer Mode.IN and OUT pin is used.Timestamp is also captured. +// <i> These bits define the RTC Tamper Input Action to be performed +// <id> rtc_tamper_input_action_1 +#ifndef CONF_RTC_TAMPER_INACT_1 +#define CONF_RTC_TAMPER_INACT_1 0 +#endif + +// <q> Debounce Enable for Tamper Input +// <i> Indicates Debounce should be enabled for Tamper input 1 +// <id> tamper_debounce_enable_1 +#ifndef CONF_RTC_TAMP_DEBNC_1 +#define CONF_RTC_TAMP_DEBNC_1 0 +#endif + +// </e> + +// <e> RTC Tamper Input 2 settings +// <id> tamper_input_2_settings +#ifndef CONF_TAMPER_INPUT_2_SETTINGS +#define CONF_TAMPER_INPUT_2_SETTINGS 0 +#endif + +// <q> Tamper Level Settings +// <i> Indicates Tamper input 2 level +// <id> tamper_level_2 +#ifndef CONF_RTC_TAMP_LVL_2 +#define CONF_RTC_TAMP_LVL_2 0 +#endif + +// <o> RTC Tamper Input Action +// <0x0=>OFF(Disabled) +// <0x1=>Wake and Set Tamper Flag +// <0x2=>Capture Timestamp and Set Tamper Flag +// <0x3=>Active Layer Mode.IN and OUT pin is used.Timestamp is also captured. +// <i> These bits define the RTC Tamper Input Action to be performed +// <id> rtc_tamper_input_action_2 +#ifndef CONF_RTC_TAMPER_INACT_2 +#define CONF_RTC_TAMPER_INACT_2 0 +#endif + +// <q> Debounce Enable for Tamper Input +// <i> Indicates Debounce should be enabled for Tamper input 2 +// <id> tamper_debounce_enable_2 +#ifndef CONF_RTC_TAMP_DEBNC_2 +#define CONF_RTC_TAMP_DEBNC_2 0 +#endif + +// </e> + +// <e> RTC Tamper Input 3 settings +// <id> tamper_input_3_settings +#ifndef CONF_TAMPER_INPUT_3_SETTINGS +#define CONF_TAMPER_INPUT_3_SETTINGS 0 +#endif + +// <q> Tamper Level Settings +// <i> Indicates Tamper input 3 level +// <id> tamper_level_3 +#ifndef CONF_RTC_TAMP_LVL_3 +#define CONF_RTC_TAMP_LVL_3 0 +#endif + +// <o> RTC Tamper Input Action +// <0x0=>OFF(Disabled) +// <0x1=>Wake and Set Tamper Flag +// <0x2=>Capture Timestamp and Set Tamper Flag +// <0x3=>Active Layer Mode.IN and OUT pin is used.Timestamp is also captured. +// <i> These bits define the RTC Tamper Input Action to be performed +// <id> rtc_tamper_input_action_3 +#ifndef CONF_RTC_TAMPER_INACT_3 +#define CONF_RTC_TAMPER_INACT_3 0 +#endif + +// <q> Debounce Enable for Tamper Input +// <i> Indicates Debounce should be enabled for Tamper input 3 +// <id> tamper_debounce_enable_3 +#ifndef CONF_RTC_TAMP_DEBNC_3 +#define CONF_RTC_TAMP_DEBNC_3 0 +#endif + +// </e> + +// <e> RTC Tamper Input 4 settings +// <id> tamper_input_4_settings +#ifndef CONF_TAMPER_INPUT_4_SETTINGS +#define CONF_TAMPER_INPUT_4_SETTINGS 0 +#endif + +// <q> Tamper Level Settings +// <i> Indicates Tamper input 4 level +// <id> tamper_level_4 +#ifndef CONF_RTC_TAMP_LVL_4 +#define CONF_RTC_TAMP_LVL_4 0 +#endif + +// <o> RTC Tamper Input Action +// <0x0=>OFF(Disabled) +// <0x1=>Wake and Set Tamper Flag +// <0x2=>Capture Timestamp and Set Tamper Flag +// <0x3=>Active Layer Mode.IN and OUT pin is used.Timestamp is also captured. +// <i> These bits define the RTC Tamper Input Action to be performed +// <id> rtc_tamper_input_action_4 +#ifndef CONF_RTC_TAMPER_INACT_4 +#define CONF_RTC_TAMPER_INACT_4 0 +#endif + +// <q> Debounce Enable for Tamper Input +// <i> Indicates Debounce should be enabled for Tamper input 4 +// <id> tamper_debounce_enable_4 +#ifndef CONF_RTC_TAMP_DEBNC_4 +#define CONF_RTC_TAMP_DEBNC_4 0 +#endif + +// </e> + +// <o> RTC Tamper Active Layer Frequency Prescalar +// <0x0=>DIV2 CLK_RTC_OUT is CLK_RTC /2 +// <0x1=>DIV4 CLK_RTC_OUT is CLK_RTC /4 +// <0x2=>DIV8 CLK_RTC_OUT is CLK_RTC /8 +// <0x3=>DIV16 CLK_RTC_OUT is CLK_RTC /16 +// <0x4=>DIV32 CLK_RTC_OUT is CLK_RTC /32 +// <0x5=>DIV64 CLK_RTC_OUT is CLK_RTC /64 +// <0x6=>DIV128 CLK_RTC_OUT is CLK_RTC /128 +// <0x7=>DIV256 CLK_RTC_OUT is CLK_RTC /256 +// <i> These bits define the RTC Tamper Active Layer Frequecny Prescalar +// <id> rtc_tamper_active_layer_frequency_prescalar +#ifndef CONF_RTC_TAMP_ACT_LAYER_FREQ_PRES +#define CONF_RTC_TAMP_ACT_LAYER_FREQ_PRES 0 +#endif + +// <o> RTC Tamper Debounce Frequency Prescalar +// <0x0=>DIV2 CLK_RTC_DEB is CLK_RTC /2 +// <0x1=>DIV4 CLK_RTC_DEB is CLK_RTC /4 +// <0x2=>DIV8 CLK_RTC_DEB is CLK_RTC /8 +// <0x3=>DIV16 CLK_RTC_DEB is CLK_RTC /16 +// <0x4=>DIV32 CLK_RTC_DEB is CLK_RTC /32 +// <0x5=>DIV64 CLK_RTC_DEB is CLK_RTC /64 +// <0x6=>DIV128 CLK_RTC_DEB is CLK_RTC /128 +// <0x7=>DIV256 CLK_RTC_DEB is CLK_RTC /256 +// <i> These bits define the RTC Debounce Frequency Prescalar +// <id> rtc_tamper_debounce_frequency_prescalar +#ifndef CONF_RTC_TAMP_DEBF_PRES +#define CONF_RTC_TAMP_DEBF_PRES 0 +#endif + +// <e> Event control +// <id> rtc_event_control +#ifndef CONF_RTC_EVENT_CONTROL_ENABLE +#define CONF_RTC_EVENT_CONTROL_ENABLE 0 +#endif + +// <q> Periodic Interval 0 Event Output +// <i> This bit indicates whether Periodic interval 0 event is enabled and will be generated +// <id> rtc_pereo0 +#ifndef CONF_RTC_PEREO0 +#define CONF_RTC_PEREO0 0 +#endif +// <q> Periodic Interval 1 Event Output +// <i> This bit indicates whether Periodic interval 1 event is enabled and will be generated +// <id> rtc_pereo1 +#ifndef CONF_RTC_PEREO1 +#define CONF_RTC_PEREO1 0 +#endif +// <q> Periodic Interval 2 Event Output +// <i> This bit indicates whether Periodic interval 2 event is enabled and will be generated +// <id> rtc_pereo2 +#ifndef CONF_RTC_PEREO2 +#define CONF_RTC_PEREO2 0 +#endif +// <q> Periodic Interval 3 Event Output +// <i> This bit indicates whether Periodic interval 3 event is enabled and will be generated +// <id> rtc_pereo3 +#ifndef CONF_RTC_PEREO3 +#define CONF_RTC_PEREO3 0 +#endif +// <q> Periodic Interval 4 Event Output +// <i> This bit indicates whether Periodic interval 4 event is enabled and will be generated +// <id> rtc_pereo4 +#ifndef CONF_RTC_PEREO4 +#define CONF_RTC_PEREO4 0 +#endif +// <q> Periodic Interval 5 Event Output +// <i> This bit indicates whether Periodic interval 5 event is enabled and will be generated +// <id> rtc_pereo5 +#ifndef CONF_RTC_PEREO5 +#define CONF_RTC_PEREO5 0 +#endif +// <q> Periodic Interval 6 Event Output +// <i> This bit indicates whether Periodic interval 6 event is enabled and will be generated +// <id> rtc_pereo6 +#ifndef CONF_RTC_PEREO6 +#define CONF_RTC_PEREO6 0 +#endif +// <q> Periodic Interval 7 Event Output +// <i> This bit indicates whether Periodic interval 7 event is enabled and will be generated +// <id> rtc_pereo7 +#ifndef CONF_RTC_PEREO7 +#define CONF_RTC_PEREO7 0 +#endif + +// <q> Compare 0 Event Output +// <i> This bit indicates whether Compare O event is enabled and will be generated +// <id> rtc_cmpeo0 +#ifndef CONF_RTC_COMPE0 +#define CONF_RTC_COMPE0 0 +#endif + +// <q> Overflow Event Output +// <i> This bit indicates whether Overflow event is enabled and will be generated +// <id> rtc_ovfeo +#ifndef CONF_RTC_OVFEO +#define CONF_RTC_OVFEO 0 +#endif + +// </e> + +// </h> + +// <<< end of configuration section >>> + +#endif // HPL_RTC_CONFIG_H |