diff options
Diffstat (limited to 'Sensor Watch Starter Project/hal/include/hpl_gpio.h')
-rw-r--r-- | Sensor Watch Starter Project/hal/include/hpl_gpio.h | 185 |
1 files changed, 185 insertions, 0 deletions
diff --git a/Sensor Watch Starter Project/hal/include/hpl_gpio.h b/Sensor Watch Starter Project/hal/include/hpl_gpio.h new file mode 100644 index 00000000..5cdd387b --- /dev/null +++ b/Sensor Watch Starter Project/hal/include/hpl_gpio.h @@ -0,0 +1,185 @@ +/** + * \file + * + * \brief Port related functionality declaration. + * + * Copyright (c) 2014-2018 Microchip Technology Inc. and its subsidiaries. + * + * \asf_license_start + * + * \page License + * + * Subject to your compliance with these terms, you may use Microchip + * software and any derivatives exclusively with Microchip products. + * It is your responsibility to comply with third party license terms applicable + * to your use of third party software (including open source software) that + * may accompany Microchip software. + * + * THIS SOFTWARE IS SUPPLIED BY MICROCHIP "AS IS". NO WARRANTIES, + * WHETHER EXPRESS, IMPLIED OR STATUTORY, APPLY TO THIS SOFTWARE, + * INCLUDING ANY IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY, + * AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT WILL MICROCHIP BE + * LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE, INCIDENTAL OR CONSEQUENTIAL + * LOSS, DAMAGE, COST OR EXPENSE OF ANY KIND WHATSOEVER RELATED TO THE + * SOFTWARE, HOWEVER CAUSED, EVEN IF MICROCHIP HAS BEEN ADVISED OF THE + * POSSIBILITY OR THE DAMAGES ARE FORESEEABLE. TO THE FULLEST EXTENT + * ALLOWED BY LAW, MICROCHIP'S TOTAL LIABILITY ON ALL CLAIMS IN ANY WAY + * RELATED TO THIS SOFTWARE WILL NOT EXCEED THE AMOUNT OF FEES, IF ANY, + * THAT YOU HAVE PAID DIRECTLY TO MICROCHIP FOR THIS SOFTWARE. + * + * \asf_license_stop + * + */ + +#ifndef _HPL_GPIO_H_INCLUDED +#define _HPL_GPIO_H_INCLUDED + +/** + * \addtogroup HPL Port + * + * \section hpl_port_rev Revision History + * - v1.0.0 Initial Release + * + *@{ + */ + +#include <compiler.h> + +#ifdef __cplusplus +extern "C" { +#endif +/** + * \brief Macros for the pin and port group, lower 5 + * bits stands for pin number in the group, higher 3 + * bits stands for port group + */ +#define GPIO_PIN(n) (((n)&0x1Fu) << 0) +#define GPIO_PORT(n) ((n) >> 5) +#define GPIO(port, pin) ((((port)&0x7u) << 5) + ((pin)&0x1Fu)) +#define GPIO_PIN_FUNCTION_OFF 0xffffffff + +/** + * \brief PORT pull mode settings + */ +enum gpio_pull_mode { GPIO_PULL_OFF, GPIO_PULL_UP, GPIO_PULL_DOWN }; + +/** + * \brief PORT direction settins + */ +enum gpio_direction { GPIO_DIRECTION_OFF, GPIO_DIRECTION_IN, GPIO_DIRECTION_OUT }; + +/** + * \brief PORT group abstraction + */ + +enum gpio_port { GPIO_PORTA, GPIO_PORTB, GPIO_PORTC, GPIO_PORTD, GPIO_PORTE }; + +/** + * \name HPL functions + */ +//@{ +/** + * \brief Port initialization function + * + * Port initialization function should setup the port module based + * on a static configuration file, this function should normally + * not be called directly, but is a part of hal_init() + */ +void _gpio_init(void); + +/** + * \brief Set direction on port with mask + * + * Set data direction for each pin, or disable the pin + * + * \param[in] port Ports are grouped into groups of maximum 32 pins, + * GPIO_PORTA = group 0, GPIO_PORTB = group 1, etc + * \param[in] mask Bit mask where 1 means apply direction setting to the + * corresponding pin + * \param[in] direction GPIO_DIRECTION_OFF = set pin direction to input + * and disable input buffer to disable the pin + * GPIO_DIRECTION_IN = set pin direction to input + * and enable input buffer to enable the pin + * GPIO_DIRECTION_OUT = set pin direction to output + * and disable input buffer + */ +static inline void _gpio_set_direction(const enum gpio_port port, const uint32_t mask, + const enum gpio_direction direction); + +/** + * \brief Set output level on port with mask + * + * Sets output state on pin to high or low with pin masking + * + * \param[in] port Ports are grouped into groups of maximum 32 pins, + * GPIO_PORTA = group 0, GPIO_PORTB = group 1, etc + * \param[in] mask Bit mask where 1 means apply direction setting to + * the corresponding pin + * \param[in] level true = pin level is set to 1 + * false = pin level is set to 0 + */ +static inline void _gpio_set_level(const enum gpio_port port, const uint32_t mask, const bool level); + +/** + * \brief Change output level to the opposite with mask + * + * Change pin output level to the opposite with pin masking + * + * \param[in] port Ports are grouped into groups of maximum 32 pins, + * GPIO_PORTA = group 0, GPIO_PORTB = group 1, etc + * \param[in] mask Bit mask where 1 means apply direction setting to + * the corresponding pin + */ +static inline void _gpio_toggle_level(const enum gpio_port port, const uint32_t mask); + +/** + * \brief Get input levels on all port pins + * + * Get input level on all port pins, will read IN register if configured to + * input and OUT register if configured as output + * + * \param[in] port Ports are grouped into groups of maximum 32 pins, + * GPIO_PORTA = group 0, GPIO_PORTB = group 1, etc + */ +static inline uint32_t _gpio_get_level(const enum gpio_port port); + +/** + * \brief Set pin pull mode + * + * Set pull mode on a single pin + * + * \notice This function will automatically change pin direction to input + * + * \param[in] port Ports are grouped into groups of maximum 32 pins, + * GPIO_PORTA = group 0, GPIO_PORTB = group 1, etc + * \param[in] pin The pin in the group that pull mode should be selected + * for + * \param[in] pull_mode GPIO_PULL_OFF = pull resistor on pin is disabled + * GPIO_PULL_DOWN = pull resistor on pin will pull pin + * level to ground level + * GPIO_PULL_UP = pull resistor on pin will pull pin + * level to VCC + */ +static inline void _gpio_set_pin_pull_mode(const enum gpio_port port, const uint8_t pin, + const enum gpio_pull_mode pull_mode); + +/** + * \brief Set gpio function + * + * Select which function a gpio is used for + * + * \param[in] gpio The gpio to set function for + * \param[in] function The gpio function is given by a 32-bit wide bitfield + * found in the header files for the device + * + */ +static inline void _gpio_set_pin_function(const uint32_t gpio, const uint32_t function); + +#include <hpl_gpio_base.h> +//@} + +#ifdef __cplusplus +} +#endif +/**@}*/ +#endif /* _HPL_GPIO_H_INCLUDED */ |