diff options
Diffstat (limited to 'boards/OSO-MISC-21-013')
-rw-r--r-- | boards/OSO-MISC-21-013/pins.h | 120 |
1 files changed, 0 insertions, 120 deletions
diff --git a/boards/OSO-MISC-21-013/pins.h b/boards/OSO-MISC-21-013/pins.h deleted file mode 100644 index a4e936a4..00000000 --- a/boards/OSO-MISC-21-013/pins.h +++ /dev/null @@ -1,120 +0,0 @@ -#ifndef PINS_H_INCLUDED -#define PINS_H_INCLUDED - -// Detects if we are on USB power. -#define VBUS_DET GPIO(GPIO_PORTA, 3) - -// Buttons -#define BTN_ALARM GPIO(GPIO_PORTA, 2) -#define WATCH_BTN_ALARM_EIC_CHANNEL 2 -#define BTN_LIGHT GPIO(GPIO_PORTB, 5) -#define WATCH_BTN_LIGHT_EIC_CHANNEL 5 -#define BTN_MODE GPIO(GPIO_PORTA, 7) -#define WATCH_BTN_MODE_EIC_CHANNEL 7 - -// Buzzer -#define BUZZER GPIO(GPIO_PORTA, 27) -#define WATCH_BUZZER_TCC_PINMUX PINMUX_PA27F_TCC0_WO5 -#define WATCH_BUZZER_TCC_CHANNEL 1 - -// LEDs -#define WATCH_INVERT_LED_POLARITY -#define RED GPIO(GPIO_PORTB, 22) -#define WATCH_RED_TCC_PINMUX PINMUX_PB22F_TCC0_WO2 -#define WATCH_RED_TCC_CHANNEL 2 - -#ifdef WATCH_SWAP_LED_PINS - #define GREEN GPIO(GPIO_PORTA, 4) - #define WATCH_GREEN_TCC_CHANNEL 0 - #define WATCH_GREEN_TCC_PINMUX PINMUX_PA04E_TCC0_WO0 -#else - #define GREEN GPIO(GPIO_PORTB, 23) - #define WATCH_GREEN_TCC_CHANNEL 3 - #define WATCH_GREEN_TCC_PINMUX PINMUX_PB23F_TCC0_WO3 -#endif - - -// Segment LCD -#define SLCD0 GPIO(GPIO_PORTB, 6) -#define SLCD1 GPIO(GPIO_PORTB, 7) -#define SLCD2 GPIO(GPIO_PORTB, 8) -#define SLCD3 GPIO(GPIO_PORTB, 9) -#define SLCD4 GPIO(GPIO_PORTA, 5) -#define SLCD5 GPIO(GPIO_PORTA, 6) -#define SLCD6 GPIO(GPIO_PORTA, 8) -#define SLCD7 GPIO(GPIO_PORTA, 9) -#define SLCD8 GPIO(GPIO_PORTA, 10) -#define SLCD9 GPIO(GPIO_PORTA, 11) -#define SLCD10 GPIO(GPIO_PORTB, 11) -#define SLCD11 GPIO(GPIO_PORTB, 12) -#define SLCD12 GPIO(GPIO_PORTB, 13) -#define SLCD13 GPIO(GPIO_PORTB, 14) -#define SLCD14 GPIO(GPIO_PORTB, 15) -#define SLCD15 GPIO(GPIO_PORTA, 14) -#define SLCD16 GPIO(GPIO_PORTA, 15) -#define SLCD17 GPIO(GPIO_PORTA, 16) -#define SLCD18 GPIO(GPIO_PORTA, 17) -#define SLCD19 GPIO(GPIO_PORTA, 18) -#define SLCD20 GPIO(GPIO_PORTA, 19) -#define SLCD21 GPIO(GPIO_PORTB, 16) -#define SLCD22 GPIO(GPIO_PORTB, 17) -#define SLCD23 GPIO(GPIO_PORTA, 20) -#define SLCD24 GPIO(GPIO_PORTA, 21) -#define SLCD25 GPIO(GPIO_PORTA, 22) -#define SLCD26 GPIO(GPIO_PORTA, 23) -// This board uses a slightly different pin mapping from the standard watch, and it's not enough to -// just declare the pins. We also have to set the LCD Pin Enable register with the SLCD pins we're -// using. These numbers are not port/pin numbers, but the "SLCD/LP[x]" numbers in the pinmux table. -// If not defined in pins.h, the LCD drover will fall back to the pin mapping in hpl_slcd_config.h. -// LPENL is for pins SLCD/LP[0..31]. -#define CONF_SLCD_LPENL (\ - (uint32_t)1 << 0 | \ - (uint32_t)1 << 1 | \ - (uint32_t)1 << 2 | \ - (uint32_t)1 << 3 | \ - (uint32_t)1 << 5 | \ - (uint32_t)1 << 6 | \ - (uint32_t)1 << 11 | \ - (uint32_t)1 << 12 | \ - (uint32_t)1 << 13 | \ - (uint32_t)1 << 14 | \ - (uint32_t)1 << 21 | \ - (uint32_t)1 << 22 | \ - (uint32_t)1 << 23 | \ - (uint32_t)1 << 24 | \ - (uint32_t)1 << 25 | \ - (uint32_t)1 << 30 | \ - (uint32_t)1 << 31 | 0) -// LPENH is for pins SLCD/LP[32..51], where bit 0 represents pin 32. -#define CONF_SLCD_LPENH (\ - (uint32_t)1 << (32 - 32) | \ - (uint32_t)1 << (33 - 32) | \ - (uint32_t)1 << (34 - 32) | \ - (uint32_t)1 << (35 - 32) | \ - (uint32_t)1 << (42 - 32) | \ - (uint32_t)1 << (43 - 32) | \ - (uint32_t)1 << (48 - 32) | \ - (uint32_t)1 << (49 - 32) | \ - (uint32_t)1 << (50 - 32) | \ - (uint32_t)1 << (51 - 32) | 0) - - -// 9-pin connector -#define A0 GPIO(GPIO_PORTB, 4) -#define WATCH_A0_EIC_CHANNEL 4 -#define A1 GPIO(GPIO_PORTB, 1) -#define WATCH_A1_EIC_CHANNEL 1 -#define A2 GPIO(GPIO_PORTB, 2) -#define WATCH_A2_EIC_CHANNEL 2 -#define A3 GPIO(GPIO_PORTB, 3) -#define WATCH_A3_EIC_CHANNEL 3 -#define A4 GPIO(GPIO_PORTB, 0) -#define WATCH_A4_EIC_CHANNEL 0 -#define SDA GPIO(GPIO_PORTB, 30) -#define SCL GPIO(GPIO_PORTB, 31) - -// aliases for as A3/A4; these were mentioned as D0/D1 in early documentation. -#define D0 GPIO(GPIO_PORTB, 3) -#define D1 GPIO(GPIO_PORTB, 0) - -#endif // PINS_H_INCLUDED |