diff options
Diffstat (limited to 'tinyusb/hw/bsp/lpcxpresso11u68')
-rwxr-xr-x | tinyusb/hw/bsp/lpcxpresso11u68/board.mk | 42 | ||||
-rwxr-xr-x | tinyusb/hw/bsp/lpcxpresso11u68/lpc11u68.ld | 242 | ||||
-rwxr-xr-x | tinyusb/hw/bsp/lpcxpresso11u68/lpcxpresso11u68.c | 135 |
3 files changed, 0 insertions, 419 deletions
diff --git a/tinyusb/hw/bsp/lpcxpresso11u68/board.mk b/tinyusb/hw/bsp/lpcxpresso11u68/board.mk deleted file mode 100755 index 922414f8..00000000 --- a/tinyusb/hw/bsp/lpcxpresso11u68/board.mk +++ /dev/null @@ -1,42 +0,0 @@ -DEPS_SUBMODULES += hw/mcu/nxp/lpcopen - -CFLAGS += \ - -flto \ - -mthumb \ - -mabi=aapcs \ - -mcpu=cortex-m0plus \ - -nostdlib \ - -DCORE_M0PLUS \ - -D__VTOR_PRESENT=0 \ - -D__USE_LPCOPEN \ - -DCFG_TUSB_MCU=OPT_MCU_LPC11UXX \ - -DCFG_TUSB_MEM_SECTION='__attribute__((section(".data.$$RAM3")))' \ - -DCFG_TUSB_MEM_ALIGN='__attribute__((aligned(64)))' - -MCU_DIR = hw/mcu/nxp/lpcopen/lpc11u6x/lpc_chip_11u6x - -# All source paths should be relative to the top level. -LD_FILE = hw/bsp/$(BOARD)/lpc11u68.ld - -SRC_C += \ - src/portable/nxp/lpc_ip3511/dcd_lpc_ip3511.c \ - $(MCU_DIR)/../gcc/cr_startup_lpc11u6x.c \ - $(MCU_DIR)/src/chip_11u6x.c \ - $(MCU_DIR)/src/clock_11u6x.c \ - $(MCU_DIR)/src/gpio_11u6x.c \ - $(MCU_DIR)/src/iocon_11u6x.c \ - $(MCU_DIR)/src/syscon_11u6x.c \ - $(MCU_DIR)/src/sysinit_11u6x.c - -INC += \ - $(TOP)/$(MCU_DIR)/inc - -# For freeRTOS port source -FREERTOS_PORT = ARM_CM0 - -# For flash-jlink target -JLINK_DEVICE = LPC11U68 - -# flash using pyocd -flash: $(BUILD)/$(PROJECT).hex - pyocd flash -t lpc11u68 $< diff --git a/tinyusb/hw/bsp/lpcxpresso11u68/lpc11u68.ld b/tinyusb/hw/bsp/lpcxpresso11u68/lpc11u68.ld deleted file mode 100755 index 56d9e4b8..00000000 --- a/tinyusb/hw/bsp/lpcxpresso11u68/lpc11u68.ld +++ /dev/null @@ -1,242 +0,0 @@ -/* - * GENERATED FILE - DO NOT EDIT - * (c) Code Red Technologies Ltd, 2008-2013 - * (c) NXP Semiconductors 2013-2019 - * Generated linker script file for LPC11U68 - * Created from linkscript.ldt by FMCreateLinkLibraries - * Using Freemarker v2.3.23 - * MCUXpresso IDE v10.2.1 [Build 795] [2018-07-25] on May 14, 2019 4:55:54 PM - */ - -MEMORY -{ - /* Define each memory region */ - MFlash256 (rx) : ORIGIN = 0x0, LENGTH = 0x40000 /* 256K bytes (alias Flash) */ - Ram0_32 (rwx) : ORIGIN = 0x10000000, LENGTH = 0x8000 /* 32K bytes (alias RAM) */ - Ram1_2 (rwx) : ORIGIN = 0x20000000, LENGTH = 0x800 /* 2K bytes (alias RAM2) */ - Ram2USB_2 (rwx) : ORIGIN = 0x20004000, LENGTH = 0x800 /* 2K bytes (alias RAM3) */ -} - - /* Define a symbol for the top of each memory region */ - __base_MFlash256 = 0x0 ; /* MFlash256 */ - __base_Flash = 0x0 ; /* Flash */ - __top_MFlash256 = 0x0 + 0x40000 ; /* 256K bytes */ - __top_Flash = 0x0 + 0x40000 ; /* 256K bytes */ - __base_Ram0_32 = 0x10000000 ; /* Ram0_32 */ - __base_RAM = 0x10000000 ; /* RAM */ - __top_Ram0_32 = 0x10000000 + 0x8000 ; /* 32K bytes */ - __top_RAM = 0x10000000 + 0x8000 ; /* 32K bytes */ - __base_Ram1_2 = 0x20000000 ; /* Ram1_2 */ - __base_RAM2 = 0x20000000 ; /* RAM2 */ - __top_Ram1_2 = 0x20000000 + 0x800 ; /* 2K bytes */ - __top_RAM2 = 0x20000000 + 0x800 ; /* 2K bytes */ - __base_Ram2USB_2 = 0x20004000 ; /* Ram2USB_2 */ - __base_RAM3 = 0x20004000 ; /* RAM3 */ - __top_Ram2USB_2 = 0x20004000 + 0x800 ; /* 2K bytes */ - __top_RAM3 = 0x20004000 + 0x800 ; /* 2K bytes */ - -ENTRY(ResetISR) - -SECTIONS -{ - /* MAIN TEXT SECTION */ - .text : ALIGN(4) - { - FILL(0xff) - __vectors_start__ = ABSOLUTE(.) ; - KEEP(*(.isr_vector)) - /* Global Section Table */ - . = ALIGN(4) ; - __section_table_start = .; - __data_section_table = .; - LONG(LOADADDR(.data)); - LONG( ADDR(.data)); - LONG( SIZEOF(.data)); - LONG(LOADADDR(.data_RAM2)); - LONG( ADDR(.data_RAM2)); - LONG( SIZEOF(.data_RAM2)); - LONG(LOADADDR(.data_RAM3)); - LONG( ADDR(.data_RAM3)); - LONG( SIZEOF(.data_RAM3)); - __data_section_table_end = .; - __bss_section_table = .; - LONG( ADDR(.bss)); - LONG( SIZEOF(.bss)); - LONG( ADDR(.bss_RAM2)); - LONG( SIZEOF(.bss_RAM2)); - LONG( ADDR(.bss_RAM3)); - LONG( SIZEOF(.bss_RAM3)); - __bss_section_table_end = .; - __section_table_end = . ; - /* End of Global Section Table */ - - *(.after_vectors*) - - } > MFlash256 - - .text : ALIGN(4) - { - *(.text*) - *(.rodata .rodata.* .constdata .constdata.*) - . = ALIGN(4); - } > MFlash256 - /* - * for exception handling/unwind - some Newlib functions (in common - * with C++ and STDC++) use this. - */ - .ARM.extab : ALIGN(4) - { - *(.ARM.extab* .gnu.linkonce.armextab.*) - } > MFlash256 - - __exidx_start = .; - - .ARM.exidx : ALIGN(4) - { - *(.ARM.exidx* .gnu.linkonce.armexidx.*) - } > MFlash256 - __exidx_end = .; - - _etext = .; - - /* possible MTB section for Ram1_2 */ - .mtb_buffer_RAM2 (NOLOAD) : - { - KEEP(*(.mtb.$RAM2*)) - KEEP(*(.mtb.$Ram1_2*)) - } > Ram1_2 - - /* DATA section for Ram1_2 */ - - .data_RAM2 : ALIGN(4) - { - FILL(0xff) - PROVIDE(__start_data_RAM2 = .) ; - *(.ramfunc.$RAM2) - *(.ramfunc.$Ram1_2) - *(.data.$RAM2*) - *(.data.$Ram1_2*) - . = ALIGN(4) ; - PROVIDE(__end_data_RAM2 = .) ; - } > Ram1_2 AT>MFlash256 - /* possible MTB section for Ram2USB_2 */ - .mtb_buffer_RAM3 (NOLOAD) : - { - KEEP(*(.mtb.$RAM3*)) - KEEP(*(.mtb.$Ram2USB_2*)) - } > Ram2USB_2 - - /* DATA section for Ram2USB_2 */ - - .data_RAM3 : ALIGN(4) - { - FILL(0xff) - PROVIDE(__start_data_RAM3 = .) ; - *(.ramfunc.$RAM3) - *(.ramfunc.$Ram2USB_2) - *(.data.$RAM3*) - *(.data.$Ram2USB_2*) - . = ALIGN(4) ; - PROVIDE(__end_data_RAM3 = .) ; - } > Ram2USB_2 AT>MFlash256 - /* MAIN DATA SECTION */ - /* Default MTB section */ - .mtb_buffer_default (NOLOAD) : - { - KEEP(*(.mtb*)) - } > Ram0_32 - .uninit_RESERVED : ALIGN(4) - { - KEEP(*(.bss.$RESERVED*)) - . = ALIGN(4) ; - _end_uninit_RESERVED = .; - } > Ram0_32 - - /* Main DATA section (Ram0_32) */ - .data : ALIGN(4) - { - FILL(0xff) - _data = . ; - *(vtable) - *(.ramfunc*) - *(.data*) - . = ALIGN(4) ; - _edata = . ; - } > Ram0_32 AT>MFlash256 - - /* BSS section for Ram1_2 */ - .bss_RAM2 : ALIGN(4) - { - PROVIDE(__start_bss_RAM2 = .) ; - *(.bss.$RAM2*) - *(.bss.$Ram1_2*) - . = ALIGN (. != 0 ? 4 : 1) ; /* avoid empty segment */ - PROVIDE(__end_bss_RAM2 = .) ; - } > Ram1_2 - - /* BSS section for Ram2USB_2 */ - .bss_RAM3 : ALIGN(4) - { - PROVIDE(__start_bss_RAM3 = .) ; - *(.bss.$RAM3*) - *(.bss.$Ram2USB_2*) - . = ALIGN (. != 0 ? 4 : 1) ; /* avoid empty segment */ - PROVIDE(__end_bss_RAM3 = .) ; - } > Ram2USB_2 - - /* MAIN BSS SECTION */ - .bss : ALIGN(4) - { - _bss = .; - *(.bss*) - *(COMMON) - . = ALIGN(4) ; - _ebss = .; - PROVIDE(end = .); - } > Ram0_32 - - /* NOINIT section for Ram1_2 */ - .noinit_RAM2 (NOLOAD) : ALIGN(4) - { - *(.noinit.$RAM2*) - *(.noinit.$Ram1_2*) - . = ALIGN(4) ; - } > Ram1_2 - - /* NOINIT section for Ram2USB_2 */ - .noinit_RAM3 (NOLOAD) : ALIGN(4) - { - *(.noinit.$RAM3*) - *(.noinit.$Ram2USB_2*) - . = ALIGN(4) ; - } > Ram2USB_2 - - /* DEFAULT NOINIT SECTION */ - .noinit (NOLOAD): ALIGN(4) - { - _noinit = .; - *(.noinit*) - . = ALIGN(4) ; - _end_noinit = .; - } > Ram0_32 - PROVIDE(_pvHeapStart = DEFINED(__user_heap_base) ? __user_heap_base : .); - PROVIDE(_vStackTop = DEFINED(__user_stack_top) ? __user_stack_top : __top_Ram0_32 - 0); - - /* ## Create checksum value (used in startup) ## */ - PROVIDE(__valid_user_code_checksum = 0 - - (_vStackTop - + (ResetISR + 1) - + (( DEFINED(NMI_Handler) ? NMI_Handler : M0_NMI_Handler ) + 1) - + (( DEFINED(HardFault_Handler) ? HardFault_Handler : M0_HardFault_Handler ) + 1) - ) - ); - - /* Provide basic symbols giving location and size of main text - * block, including initial values of RW data sections. Note that - * these will need extending to give a complete picture with - * complex images (e.g multiple Flash banks). - */ - _image_start = LOADADDR(.text); - _image_end = LOADADDR(.data) + SIZEOF(.data); - _image_size = _image_end - _image_start; -}
\ No newline at end of file diff --git a/tinyusb/hw/bsp/lpcxpresso11u68/lpcxpresso11u68.c b/tinyusb/hw/bsp/lpcxpresso11u68/lpcxpresso11u68.c deleted file mode 100755 index e33a5c6e..00000000 --- a/tinyusb/hw/bsp/lpcxpresso11u68/lpcxpresso11u68.c +++ /dev/null @@ -1,135 +0,0 @@ -/* - * The MIT License (MIT) - * - * Copyright (c) 2019 Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. - * - * This file is part of the TinyUSB stack. - */ - -#include "chip.h" -#include "../board.h" - -//--------------------------------------------------------------------+ -// Forward USB interrupt events to TinyUSB IRQ Handler -//--------------------------------------------------------------------+ -void USB_IRQHandler(void) -{ - tud_int_handler(0); -} - -//--------------------------------------------------------------------+ -// MACRO TYPEDEF CONSTANT ENUM -//--------------------------------------------------------------------+ -#define LED_PORT 2 -#define LED_PIN 17 -#define LED_STATE_ON 0 - -// Wake up Switch -#define BUTTON_PORT 0 -#define BUTTON_PIN 16 -#define BUTTON_STATE_ACTIVE 0 - -/* System oscillator rate and RTC oscillator rate */ -const uint32_t OscRateIn = 12000000; -const uint32_t RTCOscRateIn = 32768; - -/* Pin muxing table, only items that need changing from their default pin - state are in this table. Not every pin is mapped. */ -static const PINMUX_GRP_T pinmuxing[] = -{ - {0, 3, (IOCON_FUNC1 | IOCON_MODE_INACT | IOCON_DIGMODE_EN)}, // USB VBUS - {0, 18, (IOCON_FUNC1 | IOCON_MODE_INACT | IOCON_DIGMODE_EN)}, // UART0 RX - {0, 19, (IOCON_FUNC1 | IOCON_MODE_INACT | IOCON_DIGMODE_EN)}, // UART0 TX - {2, 0, (IOCON_FUNC1 | IOCON_MODE_INACT)}, // XTALIN - {2, 1, (IOCON_FUNC1 | IOCON_MODE_INACT)}, // XTALOUT -}; - -// Invoked by startup code -void SystemInit(void) -{ - /* Enable IOCON clock */ - Chip_Clock_EnablePeriphClock(SYSCTL_CLOCK_IOCON); - Chip_IOCON_SetPinMuxing(LPC_IOCON, pinmuxing, sizeof(pinmuxing) / sizeof(PINMUX_GRP_T)); - Chip_SetupXtalClocking(); -} - -void board_init(void) -{ - SystemCoreClockUpdate(); - -#if CFG_TUSB_OS == OPT_OS_NONE - // 1ms tick timer - SysTick_Config(SystemCoreClock / 1000); -#elif CFG_TUSB_OS == OPT_OS_FREERTOS - // If freeRTOS is used, IRQ priority is limit by max syscall ( smaller is higher ) - NVIC_SetPriority(USB0_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY ); -#endif - - Chip_GPIO_Init(LPC_GPIO); - - // LED - Chip_GPIO_SetPinDIROutput(LPC_GPIO, LED_PORT, LED_PIN); - - // Button - Chip_GPIO_SetPinDIRInput(LPC_GPIO, BUTTON_PORT, BUTTON_PIN); - - // USB: Setup PLL clock, and power - Chip_USB_Init(); -} - -//--------------------------------------------------------------------+ -// Board porting API -//--------------------------------------------------------------------+ - -void board_led_write(bool state) -{ - Chip_GPIO_SetPinState(LPC_GPIO, LED_PORT, LED_PIN, state ? LED_STATE_ON : (1-LED_STATE_ON)); -} - -uint32_t board_button_read(void) -{ - return BUTTON_STATE_ACTIVE == Chip_GPIO_GetPinState(LPC_GPIO, BUTTON_PORT, BUTTON_PIN); -} - -int board_uart_read(uint8_t* buf, int len) -{ - (void) buf; (void) len; - return 0; -} - -int board_uart_write(void const * buf, int len) -{ - (void) buf; (void) len; - return 0; -} - -#if CFG_TUSB_OS == OPT_OS_NONE -volatile uint32_t system_ticks = 0; -void SysTick_Handler (void) -{ - system_ticks++; -} - -uint32_t board_millis(void) -{ - return system_ticks; -} -#endif |