diff options
Diffstat (limited to 'tinyusb/hw/bsp/nutiny_sdk_nuc505/board.mk')
| -rwxr-xr-x | tinyusb/hw/bsp/nutiny_sdk_nuc505/board.mk | 60 |
1 files changed, 60 insertions, 0 deletions
diff --git a/tinyusb/hw/bsp/nutiny_sdk_nuc505/board.mk b/tinyusb/hw/bsp/nutiny_sdk_nuc505/board.mk new file mode 100755 index 00000000..e8514347 --- /dev/null +++ b/tinyusb/hw/bsp/nutiny_sdk_nuc505/board.mk @@ -0,0 +1,60 @@ +DEPS_SUBMODULES += hw/mcu/nuvoton + +CFLAGS += \ + -flto \ + -mthumb \ + -mabi=aapcs-linux \ + -mcpu=cortex-m4 \ + -mfloat-abi=hard \ + -mfpu=fpv4-sp-d16 \ + -DCFG_TUSB_MCU=OPT_MCU_NUC505 + +# All source paths should be relative to the top level. +LD_FILE = hw/bsp/$(BOARD)/nuc505_flashtoram.ld + +SRC_C += \ + src/portable/nuvoton/nuc505/dcd_nuc505.c \ + hw/mcu/nuvoton/nuc505/Device/Nuvoton/NUC505Series/Source/system_NUC505Series.c \ + hw/mcu/nuvoton/nuc505/StdDriver/src/adc.c \ + hw/mcu/nuvoton/nuc505/StdDriver/src/clk.c \ + hw/mcu/nuvoton/nuc505/StdDriver/src/gpio.c \ + hw/mcu/nuvoton/nuc505/StdDriver/src/i2c.c \ + hw/mcu/nuvoton/nuc505/StdDriver/src/i2s.c \ + hw/mcu/nuvoton/nuc505/StdDriver/src/pwm.c \ + hw/mcu/nuvoton/nuc505/StdDriver/src/rtc.c \ + hw/mcu/nuvoton/nuc505/StdDriver/src/spi.c \ + hw/mcu/nuvoton/nuc505/StdDriver/src/spim.c \ + hw/mcu/nuvoton/nuc505/StdDriver/src/sys.c \ + hw/mcu/nuvoton/nuc505/StdDriver/src/timer.c \ + hw/mcu/nuvoton/nuc505/StdDriver/src/uart.c \ + hw/mcu/nuvoton/nuc505/StdDriver/src/wdt.c \ + hw/mcu/nuvoton/nuc505/StdDriver/src/wwdt.c + +SRC_S += \ + hw/mcu/nuvoton/nuc505/Device/Nuvoton/NUC505Series/Source/GCC/startup_NUC505Series.S + +INC += \ + $(TOP)/hw/mcu/nuvoton/nuc505/Device/Nuvoton/NUC505Series/Include \ + $(TOP)/hw/mcu/nuvoton/nuc505/StdDriver/inc \ + $(TOP)/hw/mcu/nuvoton/nuc505/CMSIS/Include + +# For freeRTOS port source +FREERTOS_PORT = ARM_CM4F + +# For flash-jlink target +JLINK_DEVICE = NUC505YO13Y + +# Note +# To be able to program the SPI flash, it need to boot with ICP mode "1011". +# However, in ICP mode, opencod cannot establish connection to the mcu. +# Therefore, there is no easy command line flash for NUC505 +# It is probably better to just use Nuvoton NuMicro ICP programming on windows to program the board +# - 1111 "SPI" (run from internal flash) +# - 1110 "USB" (mass storage emulator that accepts a .bin file) +# - 0111 "ICE-SPI" (allow external debugger access, but may not be programmable) +# - 1011 ICP mode (programmable via NuMicro ICP programming tool) + +# Flash using Nuvoton's openocd fork at https://github.com/OpenNuvoton/OpenOCD-Nuvoton +# Please compile and install it from github source +flash: $(BUILD)/$(PROJECT).elf + openocd -f interface/nulink.cfg -f target/numicroM4.cfg -c "program $< reset exit" |