1 files changed, 0 insertions, 85 deletions
diff --git a/tinyusb/hw/bsp/stm32f0/boards/stm32f072disco/board.h b/tinyusb/hw/bsp/stm32f0/boards/stm32f072disco/board.h
deleted file mode 100755
index 0b1824b8..00000000
--- a/tinyusb/hw/bsp/stm32f0/boards/stm32f072disco/board.h
+++ /dev/null
@@ -1,85 +0,0 @@
-/* 
- * The MIT License (MIT)
- *
- * Copyright (c) 2020, Ha Thach (tinyusb.org)
- *
- * Permission is hereby granted, free of charge, to any person obtaining a copy
- * of this software and associated documentation files (the "Software"), to deal
- * in the Software without restriction, including without limitation the rights
- * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
- * copies of the Software, and to permit persons to whom the Software is
- * furnished to do so, subject to the following conditions:
- *
- * The above copyright notice and this permission notice shall be included in
- * all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
- * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
- * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
- * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
- * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
- * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
- * THE SOFTWARE.
- *
- * This file is part of the TinyUSB stack.
- */
-
-#ifndef BOARD_H_
-#define BOARD_H_
-
-#ifdef __cplusplus
- extern "C" {
-#endif
-
-// LED
-#define LED_PORT              GPIOC
-#define LED_PIN               GPIO_PIN_6
-#define LED_STATE_ON          1
-
-// Button
-#define BUTTON_PORT           GPIOA
-#define BUTTON_PIN            GPIO_PIN_0
-#define BUTTON_STATE_ACTIVE   1
-
-// UART
-#define UART_DEV              USART1
-#define UART_CLK_EN           __HAL_RCC_USART1_CLK_ENABLE
-#define UART_GPIO_PORT        GPIOA
-#define UART_GPIO_AF          GPIO_AF1_USART1
-#define UART_TX_PIN           GPIO_PIN_9
-#define UART_RX_PIN           GPIO_PIN_10
-
-//--------------------------------------------------------------------+
-// RCC Clock
-//--------------------------------------------------------------------+
-static inline void board_stm32f0_clock_init(void)
-{
-  RCC_ClkInitTypeDef RCC_ClkInitStruct;
-  RCC_OscInitTypeDef RCC_OscInitStruct;
-
-  /* Select HSI48 Oscillator as PLL source */
-  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI48;
-  RCC_OscInitStruct.HSI48State = RCC_HSI48_ON;
-  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
-  RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI48;
-  RCC_OscInitStruct.PLL.PREDIV = RCC_PREDIV_DIV2;
-  RCC_OscInitStruct.PLL.PLLMUL = RCC_PLL_MUL2;
-  HAL_RCC_OscConfig(&RCC_OscInitStruct);
-
-  /* Select PLL as system clock source and configure the HCLK and PCLK1 clocks dividers */
-  RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1);
-  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
-  RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
-  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1;
-  HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_1);
-}
-
-static inline void board_vbus_sense_init(void)
-{
-}
-
-#ifdef __cplusplus
- }
-#endif
-
-#endif /* BOARD_H_ */