1 files changed, 0 insertions, 92 deletions
diff --git a/tinyusb/hw/bsp/stm32f1/boards/stm32f103_mini_2/board.h b/tinyusb/hw/bsp/stm32f1/boards/stm32f103_mini_2/board.h
deleted file mode 100755
index bedce7f1..00000000
--- a/tinyusb/hw/bsp/stm32f1/boards/stm32f103_mini_2/board.h
+++ /dev/null
@@ -1,92 +0,0 @@
-/* 
- * The MIT License (MIT)
- *
- * Copyright (c) 2020, Ha Thach (tinyusb.org)
- *
- * Permission is hereby granted, free of charge, to any person obtaining a copy
- * of this software and associated documentation files (the "Software"), to deal
- * in the Software without restriction, including without limitation the rights
- * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
- * copies of the Software, and to permit persons to whom the Software is
- * furnished to do so, subject to the following conditions:
- *
- * The above copyright notice and this permission notice shall be included in
- * all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
- * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
- * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
- * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
- * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
- * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
- * THE SOFTWARE.
- *
- * This file is part of the TinyUSB stack.
- */
-
-#ifndef BOARD_H_
-#define BOARD_H_
-
-#ifdef __cplusplus
- extern "C" {
-#endif
-
-// LED
-#define LED_PORT              GPIOA
-#define LED_PIN               GPIO_PIN_8
-#define LED_STATE_ON          0
-
-// Button
-#define BUTTON_PORT           GPIOA
-#define BUTTON_PIN            GPIO_PIN_0
-#define BUTTON_STATE_ACTIVE   1
-
-// UART
-//#define UART_DEV              USART1
-//#define UART_CLK_EN           __HAL_RCC_USART1_CLK_ENABLE
-//#define UART_GPIO_PORT        GPIOA
-//#define UART_GPIO_AF          GPIO_AF1_USART1
-//#define UART_TX_PIN           GPIO_PIN_9
-//#define UART_RX_PIN           GPIO_PIN_10
-
-//--------------------------------------------------------------------+
-// RCC Clock
-//--------------------------------------------------------------------+
-static inline void board_stm32f1_clock_init(void)
-{
-  RCC_ClkInitTypeDef clkinitstruct = {0};
-  RCC_OscInitTypeDef oscinitstruct = {0};
-  RCC_PeriphCLKInitTypeDef rccperiphclkinit = {0};
-
-  /* Enable HSE Oscillator and activate PLL with HSE as source */
-  oscinitstruct.OscillatorType  = RCC_OSCILLATORTYPE_HSE;
-  oscinitstruct.HSEState        = RCC_HSE_ON;
-  oscinitstruct.HSEPredivValue  = RCC_HSE_PREDIV_DIV1;
-  oscinitstruct.PLL.PLLMUL      = RCC_PLL_MUL9;
-  oscinitstruct.PLL.PLLState    = RCC_PLL_ON;
-  oscinitstruct.PLL.PLLSource   = RCC_PLLSOURCE_HSE;
-  HAL_RCC_OscConfig(&oscinitstruct);
-
-  /* USB clock selection */
-  rccperiphclkinit.PeriphClockSelection = RCC_PERIPHCLK_USB;
-  rccperiphclkinit.UsbClockSelection = RCC_USBCLKSOURCE_PLL_DIV1_5;
-  HAL_RCCEx_PeriphCLKConfig(&rccperiphclkinit);
-
-  /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
-  clkinitstruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
-  clkinitstruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
-  clkinitstruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
-  clkinitstruct.APB1CLKDivider = RCC_HCLK_DIV2;
-  clkinitstruct.APB2CLKDivider = RCC_HCLK_DIV1;
-  HAL_RCC_ClockConfig(&clkinitstruct, FLASH_LATENCY_2);
-}
-
-static inline void board_vbus_sense_init(void)
-{
-}
-
-#ifdef __cplusplus
- }
-#endif
-
-#endif /* BOARD_H_ */