diff options
Diffstat (limited to 'tinyusb/hw/bsp/stm32f207nucleo')
-rwxr-xr-x | tinyusb/hw/bsp/stm32f207nucleo/STM32F207ZGTx_FLASH.ld | 169 | ||||
-rwxr-xr-x | tinyusb/hw/bsp/stm32f207nucleo/board.mk | 48 | ||||
-rwxr-xr-x | tinyusb/hw/bsp/stm32f207nucleo/stm32f207nucleo.c | 213 | ||||
-rwxr-xr-x | tinyusb/hw/bsp/stm32f207nucleo/stm32f2xx_hal_conf.h | 407 |
4 files changed, 0 insertions, 837 deletions
diff --git a/tinyusb/hw/bsp/stm32f207nucleo/STM32F207ZGTx_FLASH.ld b/tinyusb/hw/bsp/stm32f207nucleo/STM32F207ZGTx_FLASH.ld deleted file mode 100755 index 29e387f2..00000000 --- a/tinyusb/hw/bsp/stm32f207nucleo/STM32F207ZGTx_FLASH.ld +++ /dev/null @@ -1,169 +0,0 @@ -/* -***************************************************************************** -** - -** File : LinkerScript.ld -** -** Abstract : Linker script for STM32F207IGHx Device with -** 1024KByte FLASH, 128KByte RAM -** -** Set heap size, stack size and stack location according -** to application requirements. -** -** Set memory bank area and size if external memory is used. -** -** Target : STMicroelectronics STM32 -** -** -** Distribution: The file is distributed as is, without any warranty -** of any kind. -** -** (c)Copyright Ac6. -** You may use this file as-is or modify it according to the needs of your -** project. Distribution of this file (unmodified or modified) is not -** permitted. Ac6 permit registered System Workbench for MCU users the -** rights to distribute the assembled, compiled & linked contents of this -** file as part of an application binary file, provided that it is built -** using the System Workbench for MCU toolchain. -** -***************************************************************************** -*/ - -/* Entry Point */ -ENTRY(Reset_Handler) - -/* Highest address of the user mode stack */ -_estack = 0x20020000; /* end of RAM */ -/* Generate a link error if heap and stack don't fit into RAM */ -_Min_Heap_Size = 0x200; /* required amount of heap */ -_Min_Stack_Size = 0x400; /* required amount of stack */ - -/* Specify the memory areas */ -MEMORY -{ -FLASH (rx) : ORIGIN = 0x08000000, LENGTH = 1024K -RAM (xrw) : ORIGIN = 0x20000000, LENGTH = 128K -} - -/* Define output sections */ -SECTIONS -{ - /* The startup code goes first into FLASH */ - .isr_vector : - { - . = ALIGN(4); - KEEP(*(.isr_vector)) /* Startup code */ - . = ALIGN(4); - } >FLASH - - /* The program code and other data goes into FLASH */ - .text : - { - . = ALIGN(4); - *(.text) /* .text sections (code) */ - *(.text*) /* .text* sections (code) */ - *(.glue_7) /* glue arm to thumb code */ - *(.glue_7t) /* glue thumb to arm code */ - *(.eh_frame) - - KEEP (*(.init)) - KEEP (*(.fini)) - - . = ALIGN(4); - _etext = .; /* define a global symbols at end of code */ - } >FLASH - - /* Constant data goes into FLASH */ - .rodata : - { - . = ALIGN(4); - *(.rodata) /* .rodata sections (constants, strings, etc.) */ - *(.rodata*) /* .rodata* sections (constants, strings, etc.) */ - . = ALIGN(4); - } >FLASH - - .ARM.extab : { *(.ARM.extab* .gnu.linkonce.armextab.*) } >FLASH - .ARM : { - __exidx_start = .; - *(.ARM.exidx*) - __exidx_end = .; - } >FLASH - - .preinit_array : - { - PROVIDE_HIDDEN (__preinit_array_start = .); - KEEP (*(.preinit_array*)) - PROVIDE_HIDDEN (__preinit_array_end = .); - } >FLASH - .init_array : - { - PROVIDE_HIDDEN (__init_array_start = .); - KEEP (*(SORT(.init_array.*))) - KEEP (*(.init_array*)) - PROVIDE_HIDDEN (__init_array_end = .); - } >FLASH - .fini_array : - { - PROVIDE_HIDDEN (__fini_array_start = .); - KEEP (*(SORT(.fini_array.*))) - KEEP (*(.fini_array*)) - PROVIDE_HIDDEN (__fini_array_end = .); - } >FLASH - - /* used by the startup to initialize data */ - _sidata = LOADADDR(.data); - - /* Initialized data sections goes into RAM, load LMA copy after code */ - .data : - { - . = ALIGN(4); - _sdata = .; /* create a global symbol at data start */ - *(.data) /* .data sections */ - *(.data*) /* .data* sections */ - - . = ALIGN(4); - _edata = .; /* define a global symbol at data end */ - } >RAM AT> FLASH - - - /* Uninitialized data section */ - . = ALIGN(4); - .bss : - { - /* This is used by the startup in order to initialize the .bss secion */ - _sbss = .; /* define a global symbol at bss start */ - __bss_start__ = _sbss; - *(.bss) - *(.bss*) - *(COMMON) - - . = ALIGN(4); - _ebss = .; /* define a global symbol at bss end */ - __bss_end__ = _ebss; - } >RAM - - /* User_heap_stack section, used to check that there is enough RAM left */ - ._user_heap_stack : - { - . = ALIGN(8); - PROVIDE ( end = . ); - PROVIDE ( _end = . ); - . = . + _Min_Heap_Size; - . = . + _Min_Stack_Size; - . = ALIGN(8); - } >RAM - - - - /* Remove information from the standard libraries */ - /DISCARD/ : - { - libc.a ( * ) - libm.a ( * ) - libgcc.a ( * ) - } - - .ARM.attributes 0 : { *(.ARM.attributes) } -} - - diff --git a/tinyusb/hw/bsp/stm32f207nucleo/board.mk b/tinyusb/hw/bsp/stm32f207nucleo/board.mk deleted file mode 100755 index 2b979f3d..00000000 --- a/tinyusb/hw/bsp/stm32f207nucleo/board.mk +++ /dev/null @@ -1,48 +0,0 @@ -ST_FAMILY = f2 -DEPS_SUBMODULES += lib/CMSIS_5 hw/mcu/st/cmsis_device_$(ST_FAMILY) hw/mcu/st/stm32$(ST_FAMILY)xx_hal_driver - -ST_CMSIS = hw/mcu/st/cmsis_device_$(ST_FAMILY) -ST_HAL_DRIVER = hw/mcu/st/stm32$(ST_FAMILY)xx_hal_driver - -CFLAGS += \ - -flto \ - -mthumb \ - -mabi=aapcs \ - -mcpu=cortex-m3 \ - -mfloat-abi=soft \ - -nostdlib -nostartfiles \ - -DSTM32F207xx \ - -DCFG_TUSB_MCU=OPT_MCU_STM32F2 - -# mcu driver cause following warnings -CFLAGS += -Wno-error=sign-compare - -# All source paths should be relative to the top level. -LD_FILE = hw/bsp/$(BOARD)/STM32F207ZGTx_FLASH.ld - -SRC_C += \ - src/portable/st/synopsys/dcd_synopsys.c \ - $(ST_CMSIS)/Source/Templates/system_stm32$(ST_FAMILY)xx.c \ - $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal.c \ - $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_cortex.c \ - $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_rcc.c \ - $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_rcc_ex.c \ - $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_gpio.c - -SRC_S += \ - $(ST_CMSIS)/Source/Templates/gcc/startup_stm32f207xx.s - -INC += \ - $(TOP)/lib/CMSIS_5/CMSIS/Core/Include \ - $(TOP)/$(ST_CMSIS)/Include \ - $(TOP)/$(ST_HAL_DRIVER)/Inc \ - $(TOP)/hw/bsp/$(BOARD) - -# For freeRTOS port source -FREERTOS_PORT = ARM_CM3 - -# For flash-jlink target -JLINK_DEVICE = stm32f207zg - -# flash target using on-board stlink -flash: flash-stlink diff --git a/tinyusb/hw/bsp/stm32f207nucleo/stm32f207nucleo.c b/tinyusb/hw/bsp/stm32f207nucleo/stm32f207nucleo.c deleted file mode 100755 index 619c90d6..00000000 --- a/tinyusb/hw/bsp/stm32f207nucleo/stm32f207nucleo.c +++ /dev/null @@ -1,213 +0,0 @@ -/* - * The MIT License (MIT) - * - * Copyright (c) 2019 Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. - * - * This file is part of the TinyUSB stack. - */ - -#include "../board.h" - -#include "stm32f2xx_hal.h" - -//--------------------------------------------------------------------+ -// Forward USB interrupt events to TinyUSB IRQ Handler -//--------------------------------------------------------------------+ -void OTG_FS_IRQHandler(void) -{ - tud_int_handler(0); -} - -//--------------------------------------------------------------------+ -// MACRO TYPEDEF CONSTANT ENUM -//--------------------------------------------------------------------+ - -#define LED_PORT GPIOB -#define LED_PIN GPIO_PIN_14 -#define LED_STATE_ON 1 - -#define BUTTON_PORT GPIOC -#define BUTTON_PIN GPIO_PIN_13 -#define BUTTON_STATE_ACTIVE 1 - - -// enable all LED, Button, Uart, USB clock -static void all_rcc_clk_enable(void) -{ - __HAL_RCC_GPIOA_CLK_ENABLE(); // USB D+, D- - __HAL_RCC_GPIOB_CLK_ENABLE(); // LED - __HAL_RCC_GPIOC_CLK_ENABLE(); // Button -} - -/** - * @brief System Clock Configuration - * The system Clock is configured as follow : - * System Clock source = PLL (HSE) - * SYSCLK(Hz) = 120000000 - * HCLK(Hz) = 120000000 - * AHB Prescaler = 1 - * APB1 Prescaler = 4 - * APB2 Prescaler = 2 - * HSE Frequency(Hz) = 8000000 - * PLL_M = HSE_VALUE/1000000 - * PLL_N = 240 - * PLL_P = 2 - * PLL_Q = 5 - * VDD(V) = 3.3 - * Flash Latency(WS) = 3 - * @param None - * @retval None - */ -void SystemClock_Config(void) -{ - RCC_ClkInitTypeDef RCC_ClkInitStruct; - RCC_OscInitTypeDef RCC_OscInitStruct; - - /* Enable HSE Oscillator and activate PLL with HSE as source */ - RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE; - RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS; - RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON; - RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE; - RCC_OscInitStruct.PLL.PLLM = HSE_VALUE/1000000; - RCC_OscInitStruct.PLL.PLLN = 240; - RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; - RCC_OscInitStruct.PLL.PLLQ = 5; - HAL_RCC_OscConfig(&RCC_OscInitStruct); - - /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 - clocks dividers */ - RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2); - RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; - RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; - RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4; - RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; - HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_3); -} - -void board_init(void) -{ - SystemClock_Config(); - - #if CFG_TUSB_OS == OPT_OS_NONE - // 1ms tick timer - SysTick_Config(SystemCoreClock / 1000); - #endif - - - all_rcc_clk_enable(); - - GPIO_InitTypeDef GPIO_InitStruct; - - // LED - GPIO_InitStruct.Pin = LED_PIN; - GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP; - GPIO_InitStruct.Pull = GPIO_PULLUP; - GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; - HAL_GPIO_Init(LED_PORT, &GPIO_InitStruct); - - board_led_write(false); - - // Button - GPIO_InitStruct.Pin = BUTTON_PIN; - GPIO_InitStruct.Mode = GPIO_MODE_INPUT; - GPIO_InitStruct.Pull = GPIO_PULLDOWN; - GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; - HAL_GPIO_Init(BUTTON_PORT, &GPIO_InitStruct); - - /* Configure DM DP Pins */ - GPIO_InitStruct.Pin = (GPIO_PIN_11 | GPIO_PIN_12); - GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; - GPIO_InitStruct.Pull = GPIO_NOPULL; - GPIO_InitStruct.Speed = GPIO_SPEED_HIGH; - GPIO_InitStruct.Alternate = GPIO_AF10_OTG_FS; - HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); - - /* Configure VBUS Pin */ - GPIO_InitStruct.Pin = GPIO_PIN_9; - GPIO_InitStruct.Mode = GPIO_MODE_INPUT; - GPIO_InitStruct.Pull = GPIO_NOPULL; - HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); - - /* Configure ID pin */ - GPIO_InitStruct.Pin = GPIO_PIN_10; - GPIO_InitStruct.Mode = GPIO_MODE_AF_OD; - GPIO_InitStruct.Pull = GPIO_PULLUP; - GPIO_InitStruct.Alternate = GPIO_AF10_OTG_FS; - HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); - - /* Enable USB FS Clocks */ - __HAL_RCC_USB_OTG_FS_CLK_ENABLE(); - - // Enable VBUS sense (B device) via pin PA9 - USB_OTG_FS->GCCFG &= ~USB_OTG_GCCFG_NOVBUSSENS; - USB_OTG_FS->GCCFG |= USB_OTG_GCCFG_VBUSBSEN; -} - -//--------------------------------------------------------------------+ -// Board porting API -//--------------------------------------------------------------------+ - -void board_led_write(bool state) -{ - HAL_GPIO_WritePin(LED_PORT, LED_PIN, state ? LED_STATE_ON : (1-LED_STATE_ON)); -} - -uint32_t board_button_read(void) -{ - return BUTTON_STATE_ACTIVE == HAL_GPIO_ReadPin(BUTTON_PORT, BUTTON_PIN); -} - -int board_uart_read(uint8_t* buf, int len) -{ - (void) buf; (void) len; - return 0; -} - -int board_uart_write(void const * buf, int len) -{ - (void) buf; (void) len; - return 0; -} - -#if CFG_TUSB_OS == OPT_OS_NONE -volatile uint32_t system_ticks = 0; -void SysTick_Handler (void) -{ - system_ticks++; -} - -uint32_t board_millis(void) -{ - return system_ticks; -} -#endif - -void HardFault_Handler (void) -{ - asm("bkpt"); -} - -// Required by __libc_init_array in startup code if we are compiling using -// -nostdlib/-nostartfiles. -void _init(void) -{ - -} diff --git a/tinyusb/hw/bsp/stm32f207nucleo/stm32f2xx_hal_conf.h b/tinyusb/hw/bsp/stm32f207nucleo/stm32f2xx_hal_conf.h deleted file mode 100755 index 2ab46b26..00000000 --- a/tinyusb/hw/bsp/stm32f207nucleo/stm32f2xx_hal_conf.h +++ /dev/null @@ -1,407 +0,0 @@ -/** - ****************************************************************************** - * @file stm32f2xx_hal_conf.h - * @author MCD Application Team - * @brief HAL configuration file. - ****************************************************************************** - * @attention - * - * <h2><center>© Copyright (c) 2017 STMicroelectronics. - * All rights reserved.</center></h2> - * - * This software component is licensed by ST under BSD 3-Clause license, - * the "License"; You may not use this file except in compliance with the - * License. You may obtain a copy of the License at: - * opensource.org/licenses/BSD-3-Clause - * - ****************************************************************************** - */ - -/* Define to prevent recursive inclusion -------------------------------------*/ -#ifndef __STM32F2xx_HAL_CONF_H -#define __STM32F2xx_HAL_CONF_H - -#ifdef __cplusplus - extern "C" { -#endif - -/* Exported types ------------------------------------------------------------*/ -/* Exported constants --------------------------------------------------------*/ - -/* ########################## Module Selection ############################## */ -/** - * @brief This is the list of modules to be used in the HAL driver - */ -#define HAL_MODULE_ENABLED -/* #define HAL_ADC_MODULE_ENABLED */ -/* #define HAL_CAN_MODULE_ENABLED */ -/* #define HAL_CRC_MODULE_ENABLED */ -/* #define HAL_CRYP_MODULE_ENABLED */ -/* #define HAL_DAC_MODULE_ENABLED */ -/* #define HAL_DCMI_MODULE_ENABLED */ -/* #define HAL_DMA_MODULE_ENABLED */ -/* #define HAL_ETH_MODULE_ENABLED */ -#define HAL_EXTI_MODULE_ENABLED -#define HAL_FLASH_MODULE_ENABLED -/* #define HAL_NAND_MODULE_ENABLED */ -/* #define HAL_NOR_MODULE_ENABLED */ -/* #define HAL_PCCARD_MODULE_ENABLED */ -/* #define HAL_SRAM_MODULE_ENABLED */ -/* #define HAL_HASH_MODULE_ENABLED */ -#define HAL_GPIO_MODULE_ENABLED -/* #define HAL_I2C_MODULE_ENABLED */ -/* #define HAL_I2S_MODULE_ENABLED */ -/* #define HAL_IWDG_MODULE_ENABLED */ -#define HAL_PWR_MODULE_ENABLED -#define HAL_RCC_MODULE_ENABLED -/* #define HAL_RNG_MODULE_ENABLED */ -/* #define HAL_RTC_MODULE_ENABLED */ -/* #define HAL_SD_MODULE_ENABLED */ -/* #define HAL_SPI_MODULE_ENABLED */ -/* #define HAL_TIM_MODULE_ENABLED */ -/* #define HAL_UART_MODULE_ENABLED */ -/* #define HAL_USART_MODULE_ENABLED */ -/* #define HAL_IRDA_MODULE_ENABLED */ -/* #define HAL_SMARTCARD_MODULE_ENABLED */ -/* #define HAL_WWDG_MODULE_ENABLED */ -#define HAL_CORTEX_MODULE_ENABLED -#define HAL_PCD_MODULE_ENABLED -/* #define HAL_HCD_MODULE_ENABLED */ - - -/* ########################## HSE/HSI Values adaptation ##################### */ -/** - * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. - * This value is used by the RCC HAL module to compute the system frequency - * (when HSE is used as system clock source, directly or through the PLL). - */ -#if !defined (HSE_VALUE) - #define HSE_VALUE 8000000U /*!< Value of the External oscillator in Hz */ -#endif /* HSE_VALUE */ - -#if !defined (HSE_STARTUP_TIMEOUT) - #define HSE_STARTUP_TIMEOUT 100U /*!< Time out for HSE start up, in ms */ -#endif /* HSE_STARTUP_TIMEOUT */ - -/** - * @brief Internal High Speed oscillator (HSI) value. - * This value is used by the RCC HAL module to compute the system frequency - * (when HSI is used as system clock source, directly or through the PLL). - */ -#if !defined (HSI_VALUE) - #define HSI_VALUE 16000000U /*!< Value of the Internal oscillator in Hz*/ -#endif /* HSI_VALUE */ - -/** - * @brief Internal Low Speed oscillator (LSI) value. - */ -#if !defined (LSI_VALUE) - #define LSI_VALUE 32000U /*!< LSI Typical Value in Hz*/ -#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz - The real value may vary depending on the variations - in voltage and temperature.*/ -/** - * @brief External Low Speed oscillator (LSE) value. - */ -#if !defined (LSE_VALUE) - #define LSE_VALUE 32768U /*!< Value of the External Low Speed oscillator in Hz */ -#endif /* LSE_VALUE */ - -#if !defined (LSE_STARTUP_TIMEOUT) - #define LSE_STARTUP_TIMEOUT 5000U /*!< Time out for LSE start up, in ms */ -#endif /* LSE_STARTUP_TIMEOUT */ - -/** - * @brief External clock source for I2S peripheral - * This value is used by the I2S HAL module to compute the I2S clock source - * frequency, this source is inserted directly through I2S_CKIN pad. - */ -#if !defined (EXTERNAL_CLOCK_VALUE) - #define EXTERNAL_CLOCK_VALUE 12288000U /*!< Value of the Internal oscillator in Hz*/ -#endif /* EXTERNAL_CLOCK_VALUE */ - -/* Tip: To avoid modifying this file each time you need to use different HSE, - === you can define the HSE value in your toolchain compiler preprocessor. */ - -/* ########################### System Configuration ######################### */ -/** - * @brief This is the HAL system configuration section - */ -#define VDD_VALUE 3300U /*!< Value of VDD in mv */ -#define TICK_INT_PRIORITY 0x0FU /*!< tick interrupt priority */ -#define USE_RTOS 0U -#define PREFETCH_ENABLE 1U -#define INSTRUCTION_CACHE_ENABLE 1U -#define DATA_CACHE_ENABLE 1U - -#define USE_HAL_ADC_REGISTER_CALLBACKS 0U /* ADC register callback disabled */ -#define USE_HAL_CAN_REGISTER_CALLBACKS 0U /* CAN register callback disabled */ -#define USE_HAL_CRYP_REGISTER_CALLBACKS 0U /* CRYP register callback disabled */ -#define USE_HAL_DAC_REGISTER_CALLBACKS 0U /* DAC register callback disabled */ -#define USE_HAL_DCMI_REGISTER_CALLBACKS 0U /* DCMI register callback disabled */ -#define USE_HAL_ETH_REGISTER_CALLBACKS 0U /* ETH register callback disabled */ -#define USE_HAL_HASH_REGISTER_CALLBACKS 0U /* HASH register callback disabled */ -#define USE_HAL_HCD_REGISTER_CALLBACKS 0U /* HCD register callback disabled */ -#define USE_HAL_I2C_REGISTER_CALLBACKS 0U /* I2C register callback disabled */ -#define USE_HAL_I2S_REGISTER_CALLBACKS 0U /* I2S register callback disabled */ -#define USE_HAL_MMC_REGISTER_CALLBACKS 0U /* MMC register callback disabled */ -#define USE_HAL_NAND_REGISTER_CALLBACKS 0U /* NAND register callback disabled */ -#define USE_HAL_NOR_REGISTER_CALLBACKS 0U /* NOR register callback disabled */ -#define USE_HAL_PCCARD_REGISTER_CALLBACKS 0U /* PCCARD register callback disabled */ -#define USE_HAL_PCD_REGISTER_CALLBACKS 0U /* PCD register callback disabled */ -#define USE_HAL_RTC_REGISTER_CALLBACKS 0U /* RTC register callback disabled */ -#define USE_HAL_RNG_REGISTER_CALLBACKS 0U /* RNG register callback disabled */ -#define USE_HAL_SD_REGISTER_CALLBACKS 0U /* SD register callback disabled */ -#define USE_HAL_SMARTCARD_REGISTER_CALLBACKS 0U /* SMARTCARD register callback disabled */ -#define USE_HAL_IRDA_REGISTER_CALLBACKS 0U /* IRDA register callback disabled */ -#define USE_HAL_SRAM_REGISTER_CALLBACKS 0U /* SRAM register callback disabled */ -#define USE_HAL_SPI_REGISTER_CALLBACKS 0U /* SPI register callback disabled */ -#define USE_HAL_TIM_REGISTER_CALLBACKS 0U /* TIM register callback disabled */ -#define USE_HAL_UART_REGISTER_CALLBACKS 0U /* UART register callback disabled */ -#define USE_HAL_USART_REGISTER_CALLBACKS 0U /* USART register callback disabled */ -#define USE_HAL_WWDG_REGISTER_CALLBACKS 0U /* WWDG register callback disabled */ - -/* ########################## Assert Selection ############################## */ -/** - * @brief Uncomment the line below to expanse the "assert_param" macro in the - * HAL drivers code - */ -/* #define USE_FULL_ASSERT 1U */ - -/* ################## Ethernet peripheral configuration for NUCLEO 144 board ##################### */ - -/* Section 1 : Ethernet peripheral configuration */ - -/* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */ -#define MAC_ADDR0 2U -#define MAC_ADDR1 0U -#define MAC_ADDR2 0U -#define MAC_ADDR3 0U -#define MAC_ADDR4 0U -#define MAC_ADDR5 0U - -/* Definition of the Ethernet driver buffers size and count */ -#define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */ -#define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */ -#define ETH_RXBUFNB 5U /* 5 Rx buffers of size ETH_RX_BUF_SIZE */ -#define ETH_TXBUFNB 5U /* 5 Tx buffers of size ETH_TX_BUF_SIZE */ - -/* Section 2: PHY configuration section */ - -/* LAN8742A PHY Address*/ -#define LAN8742A_PHY_ADDRESS 0x00U -/* PHY Reset delay these values are based on a 1 ms Systick interrupt*/ -#define PHY_RESET_DELAY 0x000000FFU -/* PHY Configuration delay */ -#define PHY_CONFIG_DELAY 0x00000FFFU - -#define PHY_READ_TO 0x0000FFFFU -#define PHY_WRITE_TO 0x0000FFFFU - -/* Section 3: Common PHY Registers */ - -#define PHY_BCR ((uint16_t)0x0000) /*!< Transceiver Basic Control Register */ -#define PHY_BSR ((uint16_t)0x0001) /*!< Transceiver Basic Status Register */ - -#define PHY_RESET ((uint16_t)0x8000) /*!< PHY Reset */ -#define PHY_LOOPBACK ((uint16_t)0x4000) /*!< Select loop-back mode */ -#define PHY_FULLDUPLEX_100M ((uint16_t)0x2100) /*!< Set the full-duplex mode at 100 Mb/s */ -#define PHY_HALFDUPLEX_100M ((uint16_t)0x2000) /*!< Set the half-duplex mode at 100 Mb/s */ -#define PHY_FULLDUPLEX_10M ((uint16_t)0x0100) /*!< Set the full-duplex mode at 10 Mb/s */ -#define PHY_HALFDUPLEX_10M ((uint16_t)0x0000) /*!< Set the half-duplex mode at 10 Mb/s */ -#define PHY_AUTONEGOTIATION ((uint16_t)0x1000) /*!< Enable auto-negotiation function */ -#define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200) /*!< Restart auto-negotiation function */ -#define PHY_POWERDOWN ((uint16_t)0x0800) /*!< Select the power down mode */ -#define PHY_ISOLATE ((uint16_t)0x0400) /*!< Isolate PHY from MII */ - -#define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020) /*!< Auto-Negotiation process completed */ -#define PHY_LINKED_STATUS ((uint16_t)0x0004) /*!< Valid link established */ -#define PHY_JABBER_DETECTION ((uint16_t)0x0002) /*!< Jabber condition detected */ - -/* Section 4: Extended PHY Registers */ - -#define PHY_SR ((uint16_t)0x1F) /*!< PHY special control/ status register Offset */ - -#define PHY_SPEED_STATUS ((uint16_t)0x0004) /*!< PHY Speed mask */ -#define PHY_DUPLEX_STATUS ((uint16_t)0x0010) /*!< PHY Duplex mask */ - - -#define PHY_ISFR ((uint16_t)0x1D) /*!< PHY Interrupt Source Flag register Offset */ -#define PHY_ISFR_INT4 ((uint16_t)0x0010) /*!< PHY Link down inturrupt */ - -/* ################## SPI peripheral configuration ########################## */ - -/* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver -* Activated: CRC code is present inside driver -* Deactivated: CRC code cleaned from driver -*/ - -#define USE_SPI_CRC 1U - -/* Includes ------------------------------------------------------------------*/ -/** - * @brief Include module's header file - */ - -#ifdef HAL_RCC_MODULE_ENABLED - #include "stm32f2xx_hal_rcc.h" -#endif /* HAL_RCC_MODULE_ENABLED */ - -#ifdef HAL_GPIO_MODULE_ENABLED - #include "stm32f2xx_hal_gpio.h" -#endif /* HAL_GPIO_MODULE_ENABLED */ - -#ifdef HAL_EXTI_MODULE_ENABLED - #include "stm32f2xx_hal_exti.h" -#endif /* HAL_EXTI_MODULE_ENABLED */ - -#ifdef HAL_DMA_MODULE_ENABLED - #include "stm32f2xx_hal_dma.h" -#endif /* HAL_DMA_MODULE_ENABLED */ - -#ifdef HAL_CORTEX_MODULE_ENABLED - #include "stm32f2xx_hal_cortex.h" -#endif /* HAL_CORTEX_MODULE_ENABLED */ - -#ifdef HAL_ADC_MODULE_ENABLED - #include "stm32f2xx_hal_adc.h" -#endif /* HAL_ADC_MODULE_ENABLED */ - -#ifdef HAL_CAN_MODULE_ENABLED - #include "stm32f2xx_hal_can.h" -#endif /* HAL_CAN_MODULE_ENABLED */ - -#ifdef HAL_CRC_MODULE_ENABLED - #include "stm32f2xx_hal_crc.h" -#endif /* HAL_CRC_MODULE_ENABLED */ - -#ifdef HAL_CRYP_MODULE_ENABLED - #include "stm32f2xx_hal_cryp.h" -#endif /* HAL_CRYP_MODULE_ENABLED */ - -#ifdef HAL_DAC_MODULE_ENABLED - #include "stm32f2xx_hal_dac.h" -#endif /* HAL_DAC_MODULE_ENABLED */ - -#ifdef HAL_DCMI_MODULE_ENABLED - #include "stm32f2xx_hal_dcmi.h" -#endif /* HAL_DCMI_MODULE_ENABLED */ - -#ifdef HAL_ETH_MODULE_ENABLED - #include "stm32f2xx_hal_eth.h" -#endif /* HAL_ETH_MODULE_ENABLED */ - -#ifdef HAL_FLASH_MODULE_ENABLED - #include "stm32f2xx_hal_flash.h" -#endif /* HAL_FLASH_MODULE_ENABLED */ - -#ifdef HAL_SRAM_MODULE_ENABLED - #include "stm32f2xx_hal_sram.h" -#endif /* HAL_SRAM_MODULE_ENABLED */ - -#ifdef HAL_NOR_MODULE_ENABLED - #include "stm32f2xx_hal_nor.h" -#endif /* HAL_NOR_MODULE_ENABLED */ - -#ifdef HAL_NAND_MODULE_ENABLED - #include "stm32f2xx_hal_nand.h" -#endif /* HAL_NAND_MODULE_ENABLED */ - -#ifdef HAL_PCCARD_MODULE_ENABLED - #include "stm32f2xx_hal_pccard.h" -#endif /* HAL_PCCARD_MODULE_ENABLED */ - -#ifdef HAL_HASH_MODULE_ENABLED - #include "stm32f2xx_hal_hash.h" -#endif /* HAL_HASH_MODULE_ENABLED */ - -#ifdef HAL_I2C_MODULE_ENABLED - #include "stm32f2xx_hal_i2c.h" -#endif /* HAL_I2C_MODULE_ENABLED */ - -#ifdef HAL_I2S_MODULE_ENABLED - #include "stm32f2xx_hal_i2s.h" -#endif /* HAL_I2S_MODULE_ENABLED */ - -#ifdef HAL_IWDG_MODULE_ENABLED - #include "stm32f2xx_hal_iwdg.h" -#endif /* HAL_IWDG_MODULE_ENABLED */ - -#ifdef HAL_PWR_MODULE_ENABLED - #include "stm32f2xx_hal_pwr.h" -#endif /* HAL_PWR_MODULE_ENABLED */ - -#ifdef HAL_RNG_MODULE_ENABLED - #include "stm32f2xx_hal_rng.h" -#endif /* HAL_RNG_MODULE_ENABLED */ - -#ifdef HAL_RTC_MODULE_ENABLED - #include "stm32f2xx_hal_rtc.h" -#endif /* HAL_RTC_MODULE_ENABLED */ - -#ifdef HAL_SD_MODULE_ENABLED - #include "stm32f2xx_hal_sd.h" -#endif /* HAL_SD_MODULE_ENABLED */ - -#ifdef HAL_SPI_MODULE_ENABLED - #include "stm32f2xx_hal_spi.h" -#endif /* HAL_SPI_MODULE_ENABLED */ - -#ifdef HAL_TIM_MODULE_ENABLED - #include "stm32f2xx_hal_tim.h" -#endif /* HAL_TIM_MODULE_ENABLED */ - -#ifdef HAL_UART_MODULE_ENABLED - #include "stm32f2xx_hal_uart.h" -#endif /* HAL_UART_MODULE_ENABLED */ - -#ifdef HAL_USART_MODULE_ENABLED - #include "stm32f2xx_hal_usart.h" -#endif /* HAL_USART_MODULE_ENABLED */ - -#ifdef HAL_IRDA_MODULE_ENABLED - #include "stm32f2xx_hal_irda.h" -#endif /* HAL_IRDA_MODULE_ENABLED */ - -#ifdef HAL_SMARTCARD_MODULE_ENABLED - #include "stm32f2xx_hal_smartcard.h" -#endif /* HAL_SMARTCARD_MODULE_ENABLED */ - -#ifdef HAL_WWDG_MODULE_ENABLED - #include "stm32f2xx_hal_wwdg.h" -#endif /* HAL_WWDG_MODULE_ENABLED */ - -#ifdef HAL_PCD_MODULE_ENABLED - #include "stm32f2xx_hal_pcd.h" -#endif /* HAL_PCD_MODULE_ENABLED */ - -#ifdef HAL_HCD_MODULE_ENABLED - #include "stm32f2xx_hal_hcd.h" -#endif /* HAL_HCD_MODULE_ENABLED */ - -/* Exported macro ------------------------------------------------------------*/ -#ifdef USE_FULL_ASSERT -/** - * @brief The assert_param macro is used for function's parameters check. - * @param expr: If expr is false, it calls assert_failed function - * which reports the name of the source file and the source - * line number of the call that failed. - * If expr is true, it returns no value. - * @retval None - */ - #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__)) -/* Exported functions ------------------------------------------------------- */ - void assert_failed(uint8_t* file, uint32_t line); -#else - #define assert_param(expr) ((void)0U) -#endif /* USE_FULL_ASSERT */ - - -#ifdef __cplusplus -} -#endif - -#endif /* __STM32F2xx_HAL_CONF_H */ - - -/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ |