summaryrefslogtreecommitdiffstats
path: root/tinyusb/hw/bsp/stm32f207nucleo
diff options
context:
space:
mode:
Diffstat (limited to 'tinyusb/hw/bsp/stm32f207nucleo')
-rwxr-xr-xtinyusb/hw/bsp/stm32f207nucleo/STM32F207ZGTx_FLASH.ld169
-rwxr-xr-xtinyusb/hw/bsp/stm32f207nucleo/board.mk48
-rwxr-xr-xtinyusb/hw/bsp/stm32f207nucleo/stm32f207nucleo.c213
-rwxr-xr-xtinyusb/hw/bsp/stm32f207nucleo/stm32f2xx_hal_conf.h407
4 files changed, 837 insertions, 0 deletions
diff --git a/tinyusb/hw/bsp/stm32f207nucleo/STM32F207ZGTx_FLASH.ld b/tinyusb/hw/bsp/stm32f207nucleo/STM32F207ZGTx_FLASH.ld
new file mode 100755
index 00000000..29e387f2
--- /dev/null
+++ b/tinyusb/hw/bsp/stm32f207nucleo/STM32F207ZGTx_FLASH.ld
@@ -0,0 +1,169 @@
+/*
+*****************************************************************************
+**
+
+** File : LinkerScript.ld
+**
+** Abstract : Linker script for STM32F207IGHx Device with
+** 1024KByte FLASH, 128KByte RAM
+**
+** Set heap size, stack size and stack location according
+** to application requirements.
+**
+** Set memory bank area and size if external memory is used.
+**
+** Target : STMicroelectronics STM32
+**
+**
+** Distribution: The file is distributed as is, without any warranty
+** of any kind.
+**
+** (c)Copyright Ac6.
+** You may use this file as-is or modify it according to the needs of your
+** project. Distribution of this file (unmodified or modified) is not
+** permitted. Ac6 permit registered System Workbench for MCU users the
+** rights to distribute the assembled, compiled & linked contents of this
+** file as part of an application binary file, provided that it is built
+** using the System Workbench for MCU toolchain.
+**
+*****************************************************************************
+*/
+
+/* Entry Point */
+ENTRY(Reset_Handler)
+
+/* Highest address of the user mode stack */
+_estack = 0x20020000; /* end of RAM */
+/* Generate a link error if heap and stack don't fit into RAM */
+_Min_Heap_Size = 0x200; /* required amount of heap */
+_Min_Stack_Size = 0x400; /* required amount of stack */
+
+/* Specify the memory areas */
+MEMORY
+{
+FLASH (rx) : ORIGIN = 0x08000000, LENGTH = 1024K
+RAM (xrw) : ORIGIN = 0x20000000, LENGTH = 128K
+}
+
+/* Define output sections */
+SECTIONS
+{
+ /* The startup code goes first into FLASH */
+ .isr_vector :
+ {
+ . = ALIGN(4);
+ KEEP(*(.isr_vector)) /* Startup code */
+ . = ALIGN(4);
+ } >FLASH
+
+ /* The program code and other data goes into FLASH */
+ .text :
+ {
+ . = ALIGN(4);
+ *(.text) /* .text sections (code) */
+ *(.text*) /* .text* sections (code) */
+ *(.glue_7) /* glue arm to thumb code */
+ *(.glue_7t) /* glue thumb to arm code */
+ *(.eh_frame)
+
+ KEEP (*(.init))
+ KEEP (*(.fini))
+
+ . = ALIGN(4);
+ _etext = .; /* define a global symbols at end of code */
+ } >FLASH
+
+ /* Constant data goes into FLASH */
+ .rodata :
+ {
+ . = ALIGN(4);
+ *(.rodata) /* .rodata sections (constants, strings, etc.) */
+ *(.rodata*) /* .rodata* sections (constants, strings, etc.) */
+ . = ALIGN(4);
+ } >FLASH
+
+ .ARM.extab : { *(.ARM.extab* .gnu.linkonce.armextab.*) } >FLASH
+ .ARM : {
+ __exidx_start = .;
+ *(.ARM.exidx*)
+ __exidx_end = .;
+ } >FLASH
+
+ .preinit_array :
+ {
+ PROVIDE_HIDDEN (__preinit_array_start = .);
+ KEEP (*(.preinit_array*))
+ PROVIDE_HIDDEN (__preinit_array_end = .);
+ } >FLASH
+ .init_array :
+ {
+ PROVIDE_HIDDEN (__init_array_start = .);
+ KEEP (*(SORT(.init_array.*)))
+ KEEP (*(.init_array*))
+ PROVIDE_HIDDEN (__init_array_end = .);
+ } >FLASH
+ .fini_array :
+ {
+ PROVIDE_HIDDEN (__fini_array_start = .);
+ KEEP (*(SORT(.fini_array.*)))
+ KEEP (*(.fini_array*))
+ PROVIDE_HIDDEN (__fini_array_end = .);
+ } >FLASH
+
+ /* used by the startup to initialize data */
+ _sidata = LOADADDR(.data);
+
+ /* Initialized data sections goes into RAM, load LMA copy after code */
+ .data :
+ {
+ . = ALIGN(4);
+ _sdata = .; /* create a global symbol at data start */
+ *(.data) /* .data sections */
+ *(.data*) /* .data* sections */
+
+ . = ALIGN(4);
+ _edata = .; /* define a global symbol at data end */
+ } >RAM AT> FLASH
+
+
+ /* Uninitialized data section */
+ . = ALIGN(4);
+ .bss :
+ {
+ /* This is used by the startup in order to initialize the .bss secion */
+ _sbss = .; /* define a global symbol at bss start */
+ __bss_start__ = _sbss;
+ *(.bss)
+ *(.bss*)
+ *(COMMON)
+
+ . = ALIGN(4);
+ _ebss = .; /* define a global symbol at bss end */
+ __bss_end__ = _ebss;
+ } >RAM
+
+ /* User_heap_stack section, used to check that there is enough RAM left */
+ ._user_heap_stack :
+ {
+ . = ALIGN(8);
+ PROVIDE ( end = . );
+ PROVIDE ( _end = . );
+ . = . + _Min_Heap_Size;
+ . = . + _Min_Stack_Size;
+ . = ALIGN(8);
+ } >RAM
+
+
+
+ /* Remove information from the standard libraries */
+ /DISCARD/ :
+ {
+ libc.a ( * )
+ libm.a ( * )
+ libgcc.a ( * )
+ }
+
+ .ARM.attributes 0 : { *(.ARM.attributes) }
+}
+
+
diff --git a/tinyusb/hw/bsp/stm32f207nucleo/board.mk b/tinyusb/hw/bsp/stm32f207nucleo/board.mk
new file mode 100755
index 00000000..2b979f3d
--- /dev/null
+++ b/tinyusb/hw/bsp/stm32f207nucleo/board.mk
@@ -0,0 +1,48 @@
+ST_FAMILY = f2
+DEPS_SUBMODULES += lib/CMSIS_5 hw/mcu/st/cmsis_device_$(ST_FAMILY) hw/mcu/st/stm32$(ST_FAMILY)xx_hal_driver
+
+ST_CMSIS = hw/mcu/st/cmsis_device_$(ST_FAMILY)
+ST_HAL_DRIVER = hw/mcu/st/stm32$(ST_FAMILY)xx_hal_driver
+
+CFLAGS += \
+ -flto \
+ -mthumb \
+ -mabi=aapcs \
+ -mcpu=cortex-m3 \
+ -mfloat-abi=soft \
+ -nostdlib -nostartfiles \
+ -DSTM32F207xx \
+ -DCFG_TUSB_MCU=OPT_MCU_STM32F2
+
+# mcu driver cause following warnings
+CFLAGS += -Wno-error=sign-compare
+
+# All source paths should be relative to the top level.
+LD_FILE = hw/bsp/$(BOARD)/STM32F207ZGTx_FLASH.ld
+
+SRC_C += \
+ src/portable/st/synopsys/dcd_synopsys.c \
+ $(ST_CMSIS)/Source/Templates/system_stm32$(ST_FAMILY)xx.c \
+ $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal.c \
+ $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_cortex.c \
+ $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_rcc.c \
+ $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_rcc_ex.c \
+ $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_gpio.c
+
+SRC_S += \
+ $(ST_CMSIS)/Source/Templates/gcc/startup_stm32f207xx.s
+
+INC += \
+ $(TOP)/lib/CMSIS_5/CMSIS/Core/Include \
+ $(TOP)/$(ST_CMSIS)/Include \
+ $(TOP)/$(ST_HAL_DRIVER)/Inc \
+ $(TOP)/hw/bsp/$(BOARD)
+
+# For freeRTOS port source
+FREERTOS_PORT = ARM_CM3
+
+# For flash-jlink target
+JLINK_DEVICE = stm32f207zg
+
+# flash target using on-board stlink
+flash: flash-stlink
diff --git a/tinyusb/hw/bsp/stm32f207nucleo/stm32f207nucleo.c b/tinyusb/hw/bsp/stm32f207nucleo/stm32f207nucleo.c
new file mode 100755
index 00000000..619c90d6
--- /dev/null
+++ b/tinyusb/hw/bsp/stm32f207nucleo/stm32f207nucleo.c
@@ -0,0 +1,213 @@
+/*
+ * The MIT License (MIT)
+ *
+ * Copyright (c) 2019 Ha Thach (tinyusb.org)
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy
+ * of this software and associated documentation files (the "Software"), to deal
+ * in the Software without restriction, including without limitation the rights
+ * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ * copies of the Software, and to permit persons to whom the Software is
+ * furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ * THE SOFTWARE.
+ *
+ * This file is part of the TinyUSB stack.
+ */
+
+#include "../board.h"
+
+#include "stm32f2xx_hal.h"
+
+//--------------------------------------------------------------------+
+// Forward USB interrupt events to TinyUSB IRQ Handler
+//--------------------------------------------------------------------+
+void OTG_FS_IRQHandler(void)
+{
+ tud_int_handler(0);
+}
+
+//--------------------------------------------------------------------+
+// MACRO TYPEDEF CONSTANT ENUM
+//--------------------------------------------------------------------+
+
+#define LED_PORT GPIOB
+#define LED_PIN GPIO_PIN_14
+#define LED_STATE_ON 1
+
+#define BUTTON_PORT GPIOC
+#define BUTTON_PIN GPIO_PIN_13
+#define BUTTON_STATE_ACTIVE 1
+
+
+// enable all LED, Button, Uart, USB clock
+static void all_rcc_clk_enable(void)
+{
+ __HAL_RCC_GPIOA_CLK_ENABLE(); // USB D+, D-
+ __HAL_RCC_GPIOB_CLK_ENABLE(); // LED
+ __HAL_RCC_GPIOC_CLK_ENABLE(); // Button
+}
+
+/**
+ * @brief System Clock Configuration
+ * The system Clock is configured as follow :
+ * System Clock source = PLL (HSE)
+ * SYSCLK(Hz) = 120000000
+ * HCLK(Hz) = 120000000
+ * AHB Prescaler = 1
+ * APB1 Prescaler = 4
+ * APB2 Prescaler = 2
+ * HSE Frequency(Hz) = 8000000
+ * PLL_M = HSE_VALUE/1000000
+ * PLL_N = 240
+ * PLL_P = 2
+ * PLL_Q = 5
+ * VDD(V) = 3.3
+ * Flash Latency(WS) = 3
+ * @param None
+ * @retval None
+ */
+void SystemClock_Config(void)
+{
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+
+ /* Enable HSE Oscillator and activate PLL with HSE as source */
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
+ RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS;
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
+ RCC_OscInitStruct.PLL.PLLM = HSE_VALUE/1000000;
+ RCC_OscInitStruct.PLL.PLLN = 240;
+ RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
+ RCC_OscInitStruct.PLL.PLLQ = 5;
+ HAL_RCC_OscConfig(&RCC_OscInitStruct);
+
+ /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2
+ clocks dividers */
+ RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4;
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;
+ HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_3);
+}
+
+void board_init(void)
+{
+ SystemClock_Config();
+
+ #if CFG_TUSB_OS == OPT_OS_NONE
+ // 1ms tick timer
+ SysTick_Config(SystemCoreClock / 1000);
+ #endif
+
+
+ all_rcc_clk_enable();
+
+ GPIO_InitTypeDef GPIO_InitStruct;
+
+ // LED
+ GPIO_InitStruct.Pin = LED_PIN;
+ GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
+ GPIO_InitStruct.Pull = GPIO_PULLUP;
+ GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
+ HAL_GPIO_Init(LED_PORT, &GPIO_InitStruct);
+
+ board_led_write(false);
+
+ // Button
+ GPIO_InitStruct.Pin = BUTTON_PIN;
+ GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
+ GPIO_InitStruct.Pull = GPIO_PULLDOWN;
+ GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
+ HAL_GPIO_Init(BUTTON_PORT, &GPIO_InitStruct);
+
+ /* Configure DM DP Pins */
+ GPIO_InitStruct.Pin = (GPIO_PIN_11 | GPIO_PIN_12);
+ GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+ GPIO_InitStruct.Pull = GPIO_NOPULL;
+ GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
+ GPIO_InitStruct.Alternate = GPIO_AF10_OTG_FS;
+ HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
+
+ /* Configure VBUS Pin */
+ GPIO_InitStruct.Pin = GPIO_PIN_9;
+ GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
+ GPIO_InitStruct.Pull = GPIO_NOPULL;
+ HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
+
+ /* Configure ID pin */
+ GPIO_InitStruct.Pin = GPIO_PIN_10;
+ GPIO_InitStruct.Mode = GPIO_MODE_AF_OD;
+ GPIO_InitStruct.Pull = GPIO_PULLUP;
+ GPIO_InitStruct.Alternate = GPIO_AF10_OTG_FS;
+ HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
+
+ /* Enable USB FS Clocks */
+ __HAL_RCC_USB_OTG_FS_CLK_ENABLE();
+
+ // Enable VBUS sense (B device) via pin PA9
+ USB_OTG_FS->GCCFG &= ~USB_OTG_GCCFG_NOVBUSSENS;
+ USB_OTG_FS->GCCFG |= USB_OTG_GCCFG_VBUSBSEN;
+}
+
+//--------------------------------------------------------------------+
+// Board porting API
+//--------------------------------------------------------------------+
+
+void board_led_write(bool state)
+{
+ HAL_GPIO_WritePin(LED_PORT, LED_PIN, state ? LED_STATE_ON : (1-LED_STATE_ON));
+}
+
+uint32_t board_button_read(void)
+{
+ return BUTTON_STATE_ACTIVE == HAL_GPIO_ReadPin(BUTTON_PORT, BUTTON_PIN);
+}
+
+int board_uart_read(uint8_t* buf, int len)
+{
+ (void) buf; (void) len;
+ return 0;
+}
+
+int board_uart_write(void const * buf, int len)
+{
+ (void) buf; (void) len;
+ return 0;
+}
+
+#if CFG_TUSB_OS == OPT_OS_NONE
+volatile uint32_t system_ticks = 0;
+void SysTick_Handler (void)
+{
+ system_ticks++;
+}
+
+uint32_t board_millis(void)
+{
+ return system_ticks;
+}
+#endif
+
+void HardFault_Handler (void)
+{
+ asm("bkpt");
+}
+
+// Required by __libc_init_array in startup code if we are compiling using
+// -nostdlib/-nostartfiles.
+void _init(void)
+{
+
+}
diff --git a/tinyusb/hw/bsp/stm32f207nucleo/stm32f2xx_hal_conf.h b/tinyusb/hw/bsp/stm32f207nucleo/stm32f2xx_hal_conf.h
new file mode 100755
index 00000000..2ab46b26
--- /dev/null
+++ b/tinyusb/hw/bsp/stm32f207nucleo/stm32f2xx_hal_conf.h
@@ -0,0 +1,407 @@
+/**
+ ******************************************************************************
+ * @file stm32f2xx_hal_conf.h
+ * @author MCD Application Team
+ * @brief HAL configuration file.
+ ******************************************************************************
+ * @attention
+ *
+ * <h2><center>&copy; Copyright (c) 2017 STMicroelectronics.
+ * All rights reserved.</center></h2>
+ *
+ * This software component is licensed by ST under BSD 3-Clause license,
+ * the "License"; You may not use this file except in compliance with the
+ * License. You may obtain a copy of the License at:
+ * opensource.org/licenses/BSD-3-Clause
+ *
+ ******************************************************************************
+ */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F2xx_HAL_CONF_H
+#define __STM32F2xx_HAL_CONF_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Exported types ------------------------------------------------------------*/
+/* Exported constants --------------------------------------------------------*/
+
+/* ########################## Module Selection ############################## */
+/**
+ * @brief This is the list of modules to be used in the HAL driver
+ */
+#define HAL_MODULE_ENABLED
+/* #define HAL_ADC_MODULE_ENABLED */
+/* #define HAL_CAN_MODULE_ENABLED */
+/* #define HAL_CRC_MODULE_ENABLED */
+/* #define HAL_CRYP_MODULE_ENABLED */
+/* #define HAL_DAC_MODULE_ENABLED */
+/* #define HAL_DCMI_MODULE_ENABLED */
+/* #define HAL_DMA_MODULE_ENABLED */
+/* #define HAL_ETH_MODULE_ENABLED */
+#define HAL_EXTI_MODULE_ENABLED
+#define HAL_FLASH_MODULE_ENABLED
+/* #define HAL_NAND_MODULE_ENABLED */
+/* #define HAL_NOR_MODULE_ENABLED */
+/* #define HAL_PCCARD_MODULE_ENABLED */
+/* #define HAL_SRAM_MODULE_ENABLED */
+/* #define HAL_HASH_MODULE_ENABLED */
+#define HAL_GPIO_MODULE_ENABLED
+/* #define HAL_I2C_MODULE_ENABLED */
+/* #define HAL_I2S_MODULE_ENABLED */
+/* #define HAL_IWDG_MODULE_ENABLED */
+#define HAL_PWR_MODULE_ENABLED
+#define HAL_RCC_MODULE_ENABLED
+/* #define HAL_RNG_MODULE_ENABLED */
+/* #define HAL_RTC_MODULE_ENABLED */
+/* #define HAL_SD_MODULE_ENABLED */
+/* #define HAL_SPI_MODULE_ENABLED */
+/* #define HAL_TIM_MODULE_ENABLED */
+/* #define HAL_UART_MODULE_ENABLED */
+/* #define HAL_USART_MODULE_ENABLED */
+/* #define HAL_IRDA_MODULE_ENABLED */
+/* #define HAL_SMARTCARD_MODULE_ENABLED */
+/* #define HAL_WWDG_MODULE_ENABLED */
+#define HAL_CORTEX_MODULE_ENABLED
+#define HAL_PCD_MODULE_ENABLED
+/* #define HAL_HCD_MODULE_ENABLED */
+
+
+/* ########################## HSE/HSI Values adaptation ##################### */
+/**
+ * @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
+ * This value is used by the RCC HAL module to compute the system frequency
+ * (when HSE is used as system clock source, directly or through the PLL).
+ */
+#if !defined (HSE_VALUE)
+ #define HSE_VALUE 8000000U /*!< Value of the External oscillator in Hz */
+#endif /* HSE_VALUE */
+
+#if !defined (HSE_STARTUP_TIMEOUT)
+ #define HSE_STARTUP_TIMEOUT 100U /*!< Time out for HSE start up, in ms */
+#endif /* HSE_STARTUP_TIMEOUT */
+
+/**
+ * @brief Internal High Speed oscillator (HSI) value.
+ * This value is used by the RCC HAL module to compute the system frequency
+ * (when HSI is used as system clock source, directly or through the PLL).
+ */
+#if !defined (HSI_VALUE)
+ #define HSI_VALUE 16000000U /*!< Value of the Internal oscillator in Hz*/
+#endif /* HSI_VALUE */
+
+/**
+ * @brief Internal Low Speed oscillator (LSI) value.
+ */
+#if !defined (LSI_VALUE)
+ #define LSI_VALUE 32000U /*!< LSI Typical Value in Hz*/
+#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz
+ The real value may vary depending on the variations
+ in voltage and temperature.*/
+/**
+ * @brief External Low Speed oscillator (LSE) value.
+ */
+#if !defined (LSE_VALUE)
+ #define LSE_VALUE 32768U /*!< Value of the External Low Speed oscillator in Hz */
+#endif /* LSE_VALUE */
+
+#if !defined (LSE_STARTUP_TIMEOUT)
+ #define LSE_STARTUP_TIMEOUT 5000U /*!< Time out for LSE start up, in ms */
+#endif /* LSE_STARTUP_TIMEOUT */
+
+/**
+ * @brief External clock source for I2S peripheral
+ * This value is used by the I2S HAL module to compute the I2S clock source
+ * frequency, this source is inserted directly through I2S_CKIN pad.
+ */
+#if !defined (EXTERNAL_CLOCK_VALUE)
+ #define EXTERNAL_CLOCK_VALUE 12288000U /*!< Value of the Internal oscillator in Hz*/
+#endif /* EXTERNAL_CLOCK_VALUE */
+
+/* Tip: To avoid modifying this file each time you need to use different HSE,
+ === you can define the HSE value in your toolchain compiler preprocessor. */
+
+/* ########################### System Configuration ######################### */
+/**
+ * @brief This is the HAL system configuration section
+ */
+#define VDD_VALUE 3300U /*!< Value of VDD in mv */
+#define TICK_INT_PRIORITY 0x0FU /*!< tick interrupt priority */
+#define USE_RTOS 0U
+#define PREFETCH_ENABLE 1U
+#define INSTRUCTION_CACHE_ENABLE 1U
+#define DATA_CACHE_ENABLE 1U
+
+#define USE_HAL_ADC_REGISTER_CALLBACKS 0U /* ADC register callback disabled */
+#define USE_HAL_CAN_REGISTER_CALLBACKS 0U /* CAN register callback disabled */
+#define USE_HAL_CRYP_REGISTER_CALLBACKS 0U /* CRYP register callback disabled */
+#define USE_HAL_DAC_REGISTER_CALLBACKS 0U /* DAC register callback disabled */
+#define USE_HAL_DCMI_REGISTER_CALLBACKS 0U /* DCMI register callback disabled */
+#define USE_HAL_ETH_REGISTER_CALLBACKS 0U /* ETH register callback disabled */
+#define USE_HAL_HASH_REGISTER_CALLBACKS 0U /* HASH register callback disabled */
+#define USE_HAL_HCD_REGISTER_CALLBACKS 0U /* HCD register callback disabled */
+#define USE_HAL_I2C_REGISTER_CALLBACKS 0U /* I2C register callback disabled */
+#define USE_HAL_I2S_REGISTER_CALLBACKS 0U /* I2S register callback disabled */
+#define USE_HAL_MMC_REGISTER_CALLBACKS 0U /* MMC register callback disabled */
+#define USE_HAL_NAND_REGISTER_CALLBACKS 0U /* NAND register callback disabled */
+#define USE_HAL_NOR_REGISTER_CALLBACKS 0U /* NOR register callback disabled */
+#define USE_HAL_PCCARD_REGISTER_CALLBACKS 0U /* PCCARD register callback disabled */
+#define USE_HAL_PCD_REGISTER_CALLBACKS 0U /* PCD register callback disabled */
+#define USE_HAL_RTC_REGISTER_CALLBACKS 0U /* RTC register callback disabled */
+#define USE_HAL_RNG_REGISTER_CALLBACKS 0U /* RNG register callback disabled */
+#define USE_HAL_SD_REGISTER_CALLBACKS 0U /* SD register callback disabled */
+#define USE_HAL_SMARTCARD_REGISTER_CALLBACKS 0U /* SMARTCARD register callback disabled */
+#define USE_HAL_IRDA_REGISTER_CALLBACKS 0U /* IRDA register callback disabled */
+#define USE_HAL_SRAM_REGISTER_CALLBACKS 0U /* SRAM register callback disabled */
+#define USE_HAL_SPI_REGISTER_CALLBACKS 0U /* SPI register callback disabled */
+#define USE_HAL_TIM_REGISTER_CALLBACKS 0U /* TIM register callback disabled */
+#define USE_HAL_UART_REGISTER_CALLBACKS 0U /* UART register callback disabled */
+#define USE_HAL_USART_REGISTER_CALLBACKS 0U /* USART register callback disabled */
+#define USE_HAL_WWDG_REGISTER_CALLBACKS 0U /* WWDG register callback disabled */
+
+/* ########################## Assert Selection ############################## */
+/**
+ * @brief Uncomment the line below to expanse the "assert_param" macro in the
+ * HAL drivers code
+ */
+/* #define USE_FULL_ASSERT 1U */
+
+/* ################## Ethernet peripheral configuration for NUCLEO 144 board ##################### */
+
+/* Section 1 : Ethernet peripheral configuration */
+
+/* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */
+#define MAC_ADDR0 2U
+#define MAC_ADDR1 0U
+#define MAC_ADDR2 0U
+#define MAC_ADDR3 0U
+#define MAC_ADDR4 0U
+#define MAC_ADDR5 0U
+
+/* Definition of the Ethernet driver buffers size and count */
+#define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */
+#define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */
+#define ETH_RXBUFNB 5U /* 5 Rx buffers of size ETH_RX_BUF_SIZE */
+#define ETH_TXBUFNB 5U /* 5 Tx buffers of size ETH_TX_BUF_SIZE */
+
+/* Section 2: PHY configuration section */
+
+/* LAN8742A PHY Address*/
+#define LAN8742A_PHY_ADDRESS 0x00U
+/* PHY Reset delay these values are based on a 1 ms Systick interrupt*/
+#define PHY_RESET_DELAY 0x000000FFU
+/* PHY Configuration delay */
+#define PHY_CONFIG_DELAY 0x00000FFFU
+
+#define PHY_READ_TO 0x0000FFFFU
+#define PHY_WRITE_TO 0x0000FFFFU
+
+/* Section 3: Common PHY Registers */
+
+#define PHY_BCR ((uint16_t)0x0000) /*!< Transceiver Basic Control Register */
+#define PHY_BSR ((uint16_t)0x0001) /*!< Transceiver Basic Status Register */
+
+#define PHY_RESET ((uint16_t)0x8000) /*!< PHY Reset */
+#define PHY_LOOPBACK ((uint16_t)0x4000) /*!< Select loop-back mode */
+#define PHY_FULLDUPLEX_100M ((uint16_t)0x2100) /*!< Set the full-duplex mode at 100 Mb/s */
+#define PHY_HALFDUPLEX_100M ((uint16_t)0x2000) /*!< Set the half-duplex mode at 100 Mb/s */
+#define PHY_FULLDUPLEX_10M ((uint16_t)0x0100) /*!< Set the full-duplex mode at 10 Mb/s */
+#define PHY_HALFDUPLEX_10M ((uint16_t)0x0000) /*!< Set the half-duplex mode at 10 Mb/s */
+#define PHY_AUTONEGOTIATION ((uint16_t)0x1000) /*!< Enable auto-negotiation function */
+#define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200) /*!< Restart auto-negotiation function */
+#define PHY_POWERDOWN ((uint16_t)0x0800) /*!< Select the power down mode */
+#define PHY_ISOLATE ((uint16_t)0x0400) /*!< Isolate PHY from MII */
+
+#define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020) /*!< Auto-Negotiation process completed */
+#define PHY_LINKED_STATUS ((uint16_t)0x0004) /*!< Valid link established */
+#define PHY_JABBER_DETECTION ((uint16_t)0x0002) /*!< Jabber condition detected */
+
+/* Section 4: Extended PHY Registers */
+
+#define PHY_SR ((uint16_t)0x1F) /*!< PHY special control/ status register Offset */
+
+#define PHY_SPEED_STATUS ((uint16_t)0x0004) /*!< PHY Speed mask */
+#define PHY_DUPLEX_STATUS ((uint16_t)0x0010) /*!< PHY Duplex mask */
+
+
+#define PHY_ISFR ((uint16_t)0x1D) /*!< PHY Interrupt Source Flag register Offset */
+#define PHY_ISFR_INT4 ((uint16_t)0x0010) /*!< PHY Link down inturrupt */
+
+/* ################## SPI peripheral configuration ########################## */
+
+/* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver
+* Activated: CRC code is present inside driver
+* Deactivated: CRC code cleaned from driver
+*/
+
+#define USE_SPI_CRC 1U
+
+/* Includes ------------------------------------------------------------------*/
+/**
+ * @brief Include module's header file
+ */
+
+#ifdef HAL_RCC_MODULE_ENABLED
+ #include "stm32f2xx_hal_rcc.h"
+#endif /* HAL_RCC_MODULE_ENABLED */
+
+#ifdef HAL_GPIO_MODULE_ENABLED
+ #include "stm32f2xx_hal_gpio.h"
+#endif /* HAL_GPIO_MODULE_ENABLED */
+
+#ifdef HAL_EXTI_MODULE_ENABLED
+ #include "stm32f2xx_hal_exti.h"
+#endif /* HAL_EXTI_MODULE_ENABLED */
+
+#ifdef HAL_DMA_MODULE_ENABLED
+ #include "stm32f2xx_hal_dma.h"
+#endif /* HAL_DMA_MODULE_ENABLED */
+
+#ifdef HAL_CORTEX_MODULE_ENABLED
+ #include "stm32f2xx_hal_cortex.h"
+#endif /* HAL_CORTEX_MODULE_ENABLED */
+
+#ifdef HAL_ADC_MODULE_ENABLED
+ #include "stm32f2xx_hal_adc.h"
+#endif /* HAL_ADC_MODULE_ENABLED */
+
+#ifdef HAL_CAN_MODULE_ENABLED
+ #include "stm32f2xx_hal_can.h"
+#endif /* HAL_CAN_MODULE_ENABLED */
+
+#ifdef HAL_CRC_MODULE_ENABLED
+ #include "stm32f2xx_hal_crc.h"
+#endif /* HAL_CRC_MODULE_ENABLED */
+
+#ifdef HAL_CRYP_MODULE_ENABLED
+ #include "stm32f2xx_hal_cryp.h"
+#endif /* HAL_CRYP_MODULE_ENABLED */
+
+#ifdef HAL_DAC_MODULE_ENABLED
+ #include "stm32f2xx_hal_dac.h"
+#endif /* HAL_DAC_MODULE_ENABLED */
+
+#ifdef HAL_DCMI_MODULE_ENABLED
+ #include "stm32f2xx_hal_dcmi.h"
+#endif /* HAL_DCMI_MODULE_ENABLED */
+
+#ifdef HAL_ETH_MODULE_ENABLED
+ #include "stm32f2xx_hal_eth.h"
+#endif /* HAL_ETH_MODULE_ENABLED */
+
+#ifdef HAL_FLASH_MODULE_ENABLED
+ #include "stm32f2xx_hal_flash.h"
+#endif /* HAL_FLASH_MODULE_ENABLED */
+
+#ifdef HAL_SRAM_MODULE_ENABLED
+ #include "stm32f2xx_hal_sram.h"
+#endif /* HAL_SRAM_MODULE_ENABLED */
+
+#ifdef HAL_NOR_MODULE_ENABLED
+ #include "stm32f2xx_hal_nor.h"
+#endif /* HAL_NOR_MODULE_ENABLED */
+
+#ifdef HAL_NAND_MODULE_ENABLED
+ #include "stm32f2xx_hal_nand.h"
+#endif /* HAL_NAND_MODULE_ENABLED */
+
+#ifdef HAL_PCCARD_MODULE_ENABLED
+ #include "stm32f2xx_hal_pccard.h"
+#endif /* HAL_PCCARD_MODULE_ENABLED */
+
+#ifdef HAL_HASH_MODULE_ENABLED
+ #include "stm32f2xx_hal_hash.h"
+#endif /* HAL_HASH_MODULE_ENABLED */
+
+#ifdef HAL_I2C_MODULE_ENABLED
+ #include "stm32f2xx_hal_i2c.h"
+#endif /* HAL_I2C_MODULE_ENABLED */
+
+#ifdef HAL_I2S_MODULE_ENABLED
+ #include "stm32f2xx_hal_i2s.h"
+#endif /* HAL_I2S_MODULE_ENABLED */
+
+#ifdef HAL_IWDG_MODULE_ENABLED
+ #include "stm32f2xx_hal_iwdg.h"
+#endif /* HAL_IWDG_MODULE_ENABLED */
+
+#ifdef HAL_PWR_MODULE_ENABLED
+ #include "stm32f2xx_hal_pwr.h"
+#endif /* HAL_PWR_MODULE_ENABLED */
+
+#ifdef HAL_RNG_MODULE_ENABLED
+ #include "stm32f2xx_hal_rng.h"
+#endif /* HAL_RNG_MODULE_ENABLED */
+
+#ifdef HAL_RTC_MODULE_ENABLED
+ #include "stm32f2xx_hal_rtc.h"
+#endif /* HAL_RTC_MODULE_ENABLED */
+
+#ifdef HAL_SD_MODULE_ENABLED
+ #include "stm32f2xx_hal_sd.h"
+#endif /* HAL_SD_MODULE_ENABLED */
+
+#ifdef HAL_SPI_MODULE_ENABLED
+ #include "stm32f2xx_hal_spi.h"
+#endif /* HAL_SPI_MODULE_ENABLED */
+
+#ifdef HAL_TIM_MODULE_ENABLED
+ #include "stm32f2xx_hal_tim.h"
+#endif /* HAL_TIM_MODULE_ENABLED */
+
+#ifdef HAL_UART_MODULE_ENABLED
+ #include "stm32f2xx_hal_uart.h"
+#endif /* HAL_UART_MODULE_ENABLED */
+
+#ifdef HAL_USART_MODULE_ENABLED
+ #include "stm32f2xx_hal_usart.h"
+#endif /* HAL_USART_MODULE_ENABLED */
+
+#ifdef HAL_IRDA_MODULE_ENABLED
+ #include "stm32f2xx_hal_irda.h"
+#endif /* HAL_IRDA_MODULE_ENABLED */
+
+#ifdef HAL_SMARTCARD_MODULE_ENABLED
+ #include "stm32f2xx_hal_smartcard.h"
+#endif /* HAL_SMARTCARD_MODULE_ENABLED */
+
+#ifdef HAL_WWDG_MODULE_ENABLED
+ #include "stm32f2xx_hal_wwdg.h"
+#endif /* HAL_WWDG_MODULE_ENABLED */
+
+#ifdef HAL_PCD_MODULE_ENABLED
+ #include "stm32f2xx_hal_pcd.h"
+#endif /* HAL_PCD_MODULE_ENABLED */
+
+#ifdef HAL_HCD_MODULE_ENABLED
+ #include "stm32f2xx_hal_hcd.h"
+#endif /* HAL_HCD_MODULE_ENABLED */
+
+/* Exported macro ------------------------------------------------------------*/
+#ifdef USE_FULL_ASSERT
+/**
+ * @brief The assert_param macro is used for function's parameters check.
+ * @param expr: If expr is false, it calls assert_failed function
+ * which reports the name of the source file and the source
+ * line number of the call that failed.
+ * If expr is true, it returns no value.
+ * @retval None
+ */
+ #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__))
+/* Exported functions ------------------------------------------------------- */
+ void assert_failed(uint8_t* file, uint32_t line);
+#else
+ #define assert_param(expr) ((void)0U)
+#endif /* USE_FULL_ASSERT */
+
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F2xx_HAL_CONF_H */
+
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
generated by cgit v1.2.3 (git 2.25.1) at 2024-08-20 03:17:17 +0000