1 files changed, 0 insertions, 101 deletions
diff --git a/tinyusb/hw/bsp/stm32f7/boards/stlinkv3mini/board.h b/tinyusb/hw/bsp/stm32f7/boards/stlinkv3mini/board.h
deleted file mode 100755
index d0ef6625..00000000
--- a/tinyusb/hw/bsp/stm32f7/boards/stlinkv3mini/board.h
+++ /dev/null
@@ -1,101 +0,0 @@
-/* 
- * The MIT License (MIT)
- *
- * Copyright (c) 2021, Ha Thach (tinyusb.org)
- *
- * Permission is hereby granted, free of charge, to any person obtaining a copy
- * of this software and associated documentation files (the "Software"), to deal
- * in the Software without restriction, including without limitation the rights
- * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
- * copies of the Software, and to permit persons to whom the Software is
- * furnished to do so, subject to the following conditions:
- *
- * The above copyright notice and this permission notice shall be included in
- * all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
- * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
- * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
- * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
- * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
- * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
- * THE SOFTWARE.
- *
- * This file is part of the TinyUSB stack.
- */
-
-#ifndef BOARD_H_
-#define BOARD_H_
-
-#ifdef __cplusplus
- extern "C" {
-#endif
-
-#define LED_PORT              GPIOA
-#define LED_PIN               GPIO_PIN_10
-#define LED_STATE_ON          1
-
-// No physical button is populated
-#define BUTTON_PORT           GPIOA
-#define BUTTON_PIN            GPIO_PIN_0
-#define BUTTON_STATE_ACTIVE   1
-
-#define UART_DEV              USART6
-#define UART_CLK_EN           __HAL_RCC_USART6_CLK_ENABLE
-#define UART_GPIO_AF          GPIO_AF8_USART6
-
-#define UART_TX_PORT          GPIOG
-#define UART_TX_PIN           GPIO_PIN_9
-
-#define UART_RX_PORT          GPIOG
-#define UART_RX_PIN           GPIO_PIN_14
-
-// VBUS Sense detection
-#define OTG_FS_VBUS_SENSE     1
-#define OTG_HS_VBUS_SENSE     0
-
-//--------------------------------------------------------------------+
-// RCC Clock
-//--------------------------------------------------------------------+
-static inline void board_clock_init(void)
-{
-  RCC_ClkInitTypeDef RCC_ClkInitStruct;
-  RCC_OscInitTypeDef RCC_OscInitStruct;
-
-  /* Enable Power Control clock */
-  __HAL_RCC_PWR_CLK_ENABLE();
-
-  /* The voltage scaling allows optimizing the power consumption when the device is
-     clocked below the maximum system frequency, to update the voltage scaling value
-     regarding system frequency refer to product datasheet.  */
-  __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
-
-  /* Enable HSE Oscillator and activate PLL with HSE as source */
-  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
-  RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS;
-  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
-  RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
-  RCC_OscInitStruct.PLL.PLLM = HSE_VALUE/1000000;
-  RCC_OscInitStruct.PLL.PLLN = 432;
-  RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
-  RCC_OscInitStruct.PLL.PLLQ = 9;
-  HAL_RCC_OscConfig(&RCC_OscInitStruct);
-
-  /* Activate the OverDrive to reach the 216 MHz Frequency */
-  HAL_PWREx_EnableOverDrive();
-
-  /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
-  RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
-  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
-  RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
-  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4;
-  RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;
-
-  HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_7);
-}
-
-#ifdef __cplusplus
- }
-#endif
-
-#endif /* BOARD_H_ */