diff options
Diffstat (limited to 'tinyusb/hw/bsp/stm32f7/boards/stm32f746nucleo/board.h')
m--------- | tinyusb | 0 | ||||
-rwxr-xr-x | tinyusb/hw/bsp/stm32f7/boards/stm32f746nucleo/board.h | 96 |
2 files changed, 0 insertions, 96 deletions
diff --git a/tinyusb b/tinyusb new file mode 160000 +Subproject f8288be03f28ad7b944e6925f49422dfa39202c diff --git a/tinyusb/hw/bsp/stm32f7/boards/stm32f746nucleo/board.h b/tinyusb/hw/bsp/stm32f7/boards/stm32f746nucleo/board.h deleted file mode 100755 index 093445ed..00000000 --- a/tinyusb/hw/bsp/stm32f7/boards/stm32f746nucleo/board.h +++ /dev/null @@ -1,96 +0,0 @@ -/* - * The MIT License (MIT) - * - * Copyright (c) 2021, Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. - * - * This file is part of the TinyUSB stack. - */ - -#ifndef BOARD_H_ -#define BOARD_H_ - -#ifdef __cplusplus - extern "C" { -#endif - -#define LED_PORT GPIOB -#define LED_PIN GPIO_PIN_14 -#define LED_STATE_ON 1 - -#define BUTTON_PORT GPIOC -#define BUTTON_PIN GPIO_PIN_13 -#define BUTTON_STATE_ACTIVE 1 - -#define UART_DEV USART3 -#define UART_CLK_EN __HAL_RCC_USART3_CLK_ENABLE -#define UART_GPIO_AF GPIO_AF7_USART3 - -#define UART_TX_PORT GPIOD -#define UART_TX_PIN GPIO_PIN_8 -#define UART_RX_PORT GPIOD -#define UART_RX_PIN GPIO_PIN_9 - -// VBUS Sense detection -#define OTG_FS_VBUS_SENSE 1 -#define OTG_HS_VBUS_SENSE 0 - -static inline void board_clock_init(void) -{ - RCC_ClkInitTypeDef RCC_ClkInitStruct; - RCC_OscInitTypeDef RCC_OscInitStruct; - - /* Enable Power Control clock */ - __HAL_RCC_PWR_CLK_ENABLE(); - - /* The voltage scaling allows optimizing the power consumption when the device is - clocked below the maximum system frequency, to update the voltage scaling value - regarding system frequency refer to product datasheet. */ - __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1); - - /* Enable HSE Oscillator and activate PLL with HSE as source */ - RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE; - RCC_OscInitStruct.HSEState = RCC_HSE_ON; - RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON; - RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE; - RCC_OscInitStruct.PLL.PLLM = HSE_VALUE/1000000; - RCC_OscInitStruct.PLL.PLLN = 432; - RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; - RCC_OscInitStruct.PLL.PLLQ = 9; - HAL_RCC_OscConfig(&RCC_OscInitStruct); - - /* Activate the OverDrive to reach the 216 MHz Frequency */ - HAL_PWREx_EnableOverDrive(); - - /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */ - RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2); - RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; - RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; - RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4; - RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; - - HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_7); -} - -#ifdef __cplusplus - } -#endif - -#endif /* BOARD_H_ */ |