diff options
Diffstat (limited to 'tinyusb/hw/bsp/stm32f7/family.c')
| -rwxr-xr-x | tinyusb/hw/bsp/stm32f7/family.c | 306 |
1 files changed, 0 insertions, 306 deletions
diff --git a/tinyusb/hw/bsp/stm32f7/family.c b/tinyusb/hw/bsp/stm32f7/family.c deleted file mode 100755 index c0d32459..00000000 --- a/tinyusb/hw/bsp/stm32f7/family.c +++ /dev/null @@ -1,306 +0,0 @@ -/* - * The MIT License (MIT) - * - * Copyright (c) 2019 William D. Jones (thor0505@comcast.net), - * Uwe Bonnes (bon@elektron.ikp.physik.tu-darmstadt.de), - * Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. - * - * This file is part of the TinyUSB stack. - */ - -#include "stm32f7xx_hal.h" -#include "bsp/board.h" -#include "board.h" - -//--------------------------------------------------------------------+ -// Forward USB interrupt events to TinyUSB IRQ Handler -//--------------------------------------------------------------------+ -void OTG_FS_IRQHandler(void) -{ - tud_int_handler(0); -} - -// Despite being call USB2_OTG -// OTG_HS is marked as RHPort1 by TinyUSB to be consistent across stm32 port -void OTG_HS_IRQHandler(void) -{ - tud_int_handler(1); -} - -//--------------------------------------------------------------------+ -// MACRO TYPEDEF CONSTANT ENUM -//--------------------------------------------------------------------+ - -UART_HandleTypeDef UartHandle; - -void board_init(void) -{ - board_clock_init(); - - // Enable All GPIOs clocks - __HAL_RCC_GPIOA_CLK_ENABLE(); - __HAL_RCC_GPIOB_CLK_ENABLE(); - __HAL_RCC_GPIOC_CLK_ENABLE(); - __HAL_RCC_GPIOD_CLK_ENABLE(); - __HAL_RCC_GPIOG_CLK_ENABLE(); - __HAL_RCC_GPIOH_CLK_ENABLE(); // ULPI NXT - __HAL_RCC_GPIOI_CLK_ENABLE(); // ULPI NXT - -#ifdef __HAL_RCC_GPIOJ_CLK_ENABLE - __HAL_RCC_GPIOJ_CLK_ENABLE(); -#endif - - UART_CLK_EN(); - -#if CFG_TUSB_OS == OPT_OS_NONE - // 1ms tick timer - SysTick_Config(SystemCoreClock / 1000); -#endif - - GPIO_InitTypeDef GPIO_InitStruct; - - // LED - GPIO_InitStruct.Pin = LED_PIN; - GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP; - GPIO_InitStruct.Pull = GPIO_PULLUP; - GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; - HAL_GPIO_Init(LED_PORT, &GPIO_InitStruct); - - // Button - GPIO_InitStruct.Pin = BUTTON_PIN; - GPIO_InitStruct.Mode = GPIO_MODE_INPUT; - GPIO_InitStruct.Pull = GPIO_NOPULL; - GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; - HAL_GPIO_Init(BUTTON_PORT, &GPIO_InitStruct); - - // Uart TX - GPIO_InitStruct.Pin = UART_TX_PIN; - GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; - GPIO_InitStruct.Pull = GPIO_PULLUP; - GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; - GPIO_InitStruct.Alternate = UART_GPIO_AF; - HAL_GPIO_Init(UART_TX_PORT, &GPIO_InitStruct); - - // Uart RX - GPIO_InitStruct.Pin = UART_RX_PIN; - GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; - GPIO_InitStruct.Pull = GPIO_PULLUP; - GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; - GPIO_InitStruct.Alternate = UART_GPIO_AF; - HAL_GPIO_Init(UART_RX_PORT, &GPIO_InitStruct); - - UartHandle.Instance = UART_DEV; - UartHandle.Init.BaudRate = CFG_BOARD_UART_BAUDRATE; - UartHandle.Init.WordLength = UART_WORDLENGTH_8B; - UartHandle.Init.StopBits = UART_STOPBITS_1; - UartHandle.Init.Parity = UART_PARITY_NONE; - UartHandle.Init.HwFlowCtl = UART_HWCONTROL_NONE; - UartHandle.Init.Mode = UART_MODE_TX_RX; - UartHandle.Init.OverSampling = UART_OVERSAMPLING_16; - HAL_UART_Init(&UartHandle); - -#if BOARD_DEVICE_RHPORT_NUM == 0 - // OTG_FS - - /* Configure DM DP Pins */ - GPIO_InitStruct.Pin = (GPIO_PIN_11 | GPIO_PIN_12); - GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; - GPIO_InitStruct.Pull = GPIO_NOPULL; - GPIO_InitStruct.Speed = GPIO_SPEED_HIGH; - GPIO_InitStruct.Alternate = GPIO_AF10_OTG_FS; - HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); - - /* Configure OTG-FS ID pin */ - GPIO_InitStruct.Pin = GPIO_PIN_10; - GPIO_InitStruct.Mode = GPIO_MODE_AF_OD; - GPIO_InitStruct.Pull = GPIO_PULLUP; - GPIO_InitStruct.Alternate = GPIO_AF10_OTG_FS; - HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); - - /* Enable USB FS Clocks */ - __HAL_RCC_USB_OTG_FS_CLK_ENABLE(); - -#if OTG_FS_VBUS_SENSE - /* Configure VBUS Pin */ - GPIO_InitStruct.Pin = GPIO_PIN_9; - GPIO_InitStruct.Mode = GPIO_MODE_INPUT; - GPIO_InitStruct.Pull = GPIO_NOPULL; - HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); - - // Enable VBUS sense (B device) via pin PA9 - USB_OTG_FS->GCCFG |= USB_OTG_GCCFG_VBDEN; -#else - // Disable VBUS sense (B device) via pin PA9 - USB_OTG_FS->GCCFG &= ~USB_OTG_GCCFG_VBDEN; - - // B-peripheral session valid override enable - USB_OTG_FS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOEN; - USB_OTG_FS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOVAL; -#endif // vbus sense - -#else - // OTG_HS - - #ifdef USB_HS_PHYC - // MCU with built-in HS PHY such as F723, F733, F730 - - /* Configure DM DP Pins */ - GPIO_InitStruct.Pin = (GPIO_PIN_14 | GPIO_PIN_15); - GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; - GPIO_InitStruct.Pull = GPIO_NOPULL; - GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; - GPIO_InitStruct.Alternate = GPIO_AF10_OTG_HS; - HAL_GPIO_Init(GPIOB, &GPIO_InitStruct); - - // Enable HS VBUS sense (B device) via pin PB13 - USB_OTG_HS->GCCFG |= USB_OTG_GCCFG_VBDEN; - - /* Configure OTG-HS ID pin */ - GPIO_InitStruct.Pin = GPIO_PIN_13; - GPIO_InitStruct.Mode = GPIO_MODE_AF_OD; - GPIO_InitStruct.Pull = GPIO_PULLUP; - GPIO_InitStruct.Alternate = GPIO_AF10_OTG_HS; - HAL_GPIO_Init(GPIOD, &GPIO_InitStruct); - - /* Enable PHYC Clocks */ - __HAL_RCC_OTGPHYC_CLK_ENABLE(); - - #else - // MUC with external ULPI PHY - - /* ULPI CLK */ - GPIO_InitStruct.Pin = GPIO_PIN_5; - GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; - GPIO_InitStruct.Pull = GPIO_NOPULL; - GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; - GPIO_InitStruct.Alternate = GPIO_AF10_OTG_HS; - HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); - - /* ULPI D0 */ - GPIO_InitStruct.Pin = GPIO_PIN_3; - GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; - GPIO_InitStruct.Pull = GPIO_NOPULL; - GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; - GPIO_InitStruct.Alternate = GPIO_AF10_OTG_HS; - HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); - - /* ULPI D1 D2 D3 D4 D5 D6 D7 */ - GPIO_InitStruct.Pin = GPIO_PIN_0 | GPIO_PIN_1 | GPIO_PIN_10 | GPIO_PIN_11 | GPIO_PIN_12 | GPIO_PIN_13 | GPIO_PIN_5; - GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; - GPIO_InitStruct.Pull = GPIO_NOPULL; - GPIO_InitStruct.Alternate = GPIO_AF10_OTG_HS; - HAL_GPIO_Init(GPIOB, &GPIO_InitStruct); - - /* ULPI STP */ - GPIO_InitStruct.Pin = GPIO_PIN_0 | GPIO_PIN_2; - GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; - GPIO_InitStruct.Pull = GPIO_NOPULL; - GPIO_InitStruct.Alternate = GPIO_AF10_OTG_HS; - HAL_GPIO_Init(GPIOC, &GPIO_InitStruct); - - /* NXT */ - GPIO_InitStruct.Pin = GPIO_PIN_4; - GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; - GPIO_InitStruct.Pull = GPIO_NOPULL; - GPIO_InitStruct.Alternate = GPIO_AF10_OTG_HS; - HAL_GPIO_Init(GPIOH, &GPIO_InitStruct); - - /* ULPI DIR */ - GPIO_InitStruct.Pin = GPIO_PIN_11; - GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; - GPIO_InitStruct.Pull = GPIO_NOPULL; - GPIO_InitStruct.Alternate = GPIO_AF10_OTG_HS; - HAL_GPIO_Init(GPIOI, &GPIO_InitStruct); - #endif // USB_HS_PHYC - - // Enable USB HS & ULPI Clocks - __HAL_RCC_USB_OTG_HS_ULPI_CLK_ENABLE(); - __HAL_RCC_USB_OTG_HS_CLK_ENABLE(); - -#if OTG_HS_VBUS_SENSE - #error OTG HS VBUS Sense enabled is not implemented -#else - // No VBUS sense - USB_OTG_HS->GCCFG &= ~USB_OTG_GCCFG_VBDEN; - - // B-peripheral session valid override enable - USB_OTG_HS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOEN; - USB_OTG_HS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOVAL; -#endif - - // Force device mode - USB_OTG_HS->GUSBCFG &= ~USB_OTG_GUSBCFG_FHMOD; - USB_OTG_HS->GUSBCFG |= USB_OTG_GUSBCFG_FDMOD; - -#endif // BOARD_DEVICE_RHPORT_NUM - -} - -//--------------------------------------------------------------------+ -// Board porting API -//--------------------------------------------------------------------+ - -void board_led_write(bool state) -{ - HAL_GPIO_WritePin(LED_PORT, LED_PIN, state ? LED_STATE_ON : (1-LED_STATE_ON)); -} - -uint32_t board_button_read(void) -{ - return HAL_GPIO_ReadPin(BUTTON_PORT, BUTTON_PIN); -} - -int board_uart_read(uint8_t* buf, int len) -{ - (void) buf; (void) len; - return 0; -} - -int board_uart_write(void const * buf, int len) -{ - HAL_UART_Transmit(&UartHandle, (uint8_t*) buf, len, 0xffff); - return len; -} - -#if CFG_TUSB_OS == OPT_OS_NONE -volatile uint32_t system_ticks = 0; -void SysTick_Handler (void) -{ - system_ticks++; -} - -uint32_t board_millis(void) -{ - return system_ticks; -} -#endif - -void HardFault_Handler (void) -{ - asm("bkpt"); -} - -// Required by __libc_init_array in startup code if we are compiling using -// -nostdlib/-nostartfiles. -void _init(void) -{ - -} |