2 files changed, 0 insertions, 132 deletions
diff --git a/tinyusb b/tinyusb
new file mode 160000
+Subproject f8288be03f28ad7b944e6925f49422dfa39202c
diff --git a/tinyusb/hw/bsp/stm32h7/boards/stm32h743eval/board.h b/tinyusb/hw/bsp/stm32h7/boards/stm32h743eval/board.h
deleted file mode 100755
index ab263d2b..00000000
--- a/tinyusb/hw/bsp/stm32h7/boards/stm32h743eval/board.h
+++ /dev/null
@@ -1,132 +0,0 @@
-/*
- * The MIT License (MIT)
- *
- * Copyright (c) 2021, Ha Thach (tinyusb.org)
- *
- * Permission is hereby granted, free of charge, to any person obtaining a copy
- * of this software and associated documentation files (the "Software"), to deal
- * in the Software without restriction, including without limitation the rights
- * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
- * copies of the Software, and to permit persons to whom the Software is
- * furnished to do so, subject to the following conditions:
- *
- * The above copyright notice and this permission notice shall be included in
- * all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
- * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
- * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
- * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
- * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
- * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
- * THE SOFTWARE.
- *
- * This file is part of the TinyUSB stack.
- */
-
-#ifndef BOARD_H_
-#define BOARD_H_
-
-#ifdef __cplusplus
- extern "C" {
-#endif
-
-#define LED_PORT              GPIOA
-#define LED_PIN               GPIO_PIN_4
-#define LED_STATE_ON          1
-
-// Tamper push-button
-#define BUTTON_PORT           GPIOC
-#define BUTTON_PIN            GPIO_PIN_13
-#define BUTTON_STATE_ACTIVE   0
-
-// Need to change jumper setting J7 and J8 from RS-232 to STLink
-#define UART_DEV              USART1
-#define UART_CLK_EN           __HAL_RCC_USART1_CLK_ENABLE
-#define UART_GPIO_PORT        GPIOB
-#define UART_GPIO_AF          GPIO_AF4_USART1
-#define UART_TX_PIN           GPIO_PIN_14
-#define UART_RX_PIN           GPIO_PIN_15
-
-// VBUS Sense detection
-#define OTG_FS_VBUS_SENSE     1
-#define OTG_HS_VBUS_SENSE     0
-
-//--------------------------------------------------------------------+
-// RCC Clock
-//--------------------------------------------------------------------+
-static inline void board_stm32h7_clock_init(void)
-{
-  RCC_ClkInitTypeDef RCC_ClkInitStruct;
-  RCC_OscInitTypeDef RCC_OscInitStruct;
-  RCC_PeriphCLKInitTypeDef PeriphClkInitStruct;
-
-  /*!< Supply configuration update enable */
-  HAL_PWREx_ConfigSupply(PWR_LDO_SUPPLY);
-
-  /* The voltage scaling allows optimizing the power consumption when the device is
-     clocked below the maximum system frequency, to update the voltage scaling value
-     regarding system frequency refer to product datasheet.  */
-  __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
-
-  while ((PWR->D3CR & (PWR_D3CR_VOSRDY)) != PWR_D3CR_VOSRDY) {}
-
-  /* Enable HSE Oscillator and activate PLL with HSE as source */
-  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
-  RCC_OscInitStruct.HSEState = RCC_HSE_ON;
-  RCC_OscInitStruct.HSIState = RCC_HSI_OFF;
-  RCC_OscInitStruct.CSIState = RCC_CSI_OFF;
-  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
-  RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
-
-  /* PLL1 for System Clock */
-  RCC_OscInitStruct.PLL.PLLM = 5;
-  RCC_OscInitStruct.PLL.PLLN = 160;
-  RCC_OscInitStruct.PLL.PLLFRACN = 0;
-  RCC_OscInitStruct.PLL.PLLP = 2;
-  RCC_OscInitStruct.PLL.PLLR = 2;
-  RCC_OscInitStruct.PLL.PLLQ = 4;
-
-  RCC_OscInitStruct.PLL.PLLVCOSEL = RCC_PLL1VCOMEDIUM;
-  RCC_OscInitStruct.PLL.PLLRGE = RCC_PLL1VCIRANGE_2;
-  HAL_RCC_OscConfig(&RCC_OscInitStruct);
-
-  /* PLL3 for USB Clock */
-  PeriphClkInitStruct.PLL3.PLL3M = 25;
-  PeriphClkInitStruct.PLL3.PLL3N = 336;
-  PeriphClkInitStruct.PLL3.PLL3FRACN = 0;
-  PeriphClkInitStruct.PLL3.PLL3P = 2;
-  PeriphClkInitStruct.PLL3.PLL3R = 2;
-  PeriphClkInitStruct.PLL3.PLL3Q = 7;
-
-  PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_USB;
-  PeriphClkInitStruct.UsbClockSelection = RCC_USBCLKSOURCE_PLL3;
-  HAL_RCCEx_PeriphCLKConfig(&PeriphClkInitStruct);
-
-  /* Select PLL as system clock source and configure  bus clocks dividers */
-  RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_D1PCLK1 | RCC_CLOCKTYPE_PCLK1 | \
-  RCC_CLOCKTYPE_PCLK2  | RCC_CLOCKTYPE_D3PCLK1);
-
-  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
-  RCC_ClkInitStruct.SYSCLKDivider = RCC_SYSCLK_DIV1;
-  RCC_ClkInitStruct.AHBCLKDivider = RCC_HCLK_DIV2;
-  RCC_ClkInitStruct.APB1CLKDivider = RCC_APB1_DIV2;
-  RCC_ClkInitStruct.APB2CLKDivider = RCC_APB2_DIV2;
-  RCC_ClkInitStruct.APB3CLKDivider = RCC_APB3_DIV1;
-  HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_4);
-
-  /*activate CSI clock mondatory for I/O Compensation Cell*/
-  __HAL_RCC_CSI_ENABLE() ;
-
-  /* Enable SYSCFG clock mondatory for I/O Compensation Cell */
-  __HAL_RCC_SYSCFG_CLK_ENABLE() ;
-
-  /* Enables the I/O Compensation Cell */
-  HAL_EnableCompensationCell();
-}
-
-#ifdef __cplusplus
- }
-#endif
-
-#endif