diff options
Diffstat (limited to 'tinyusb/hw/bsp/stm32h7/boards/stm32h743eval/board.h')
| -rwxr-xr-x | tinyusb/hw/bsp/stm32h7/boards/stm32h743eval/board.h | 132 |
1 files changed, 132 insertions, 0 deletions
diff --git a/tinyusb/hw/bsp/stm32h7/boards/stm32h743eval/board.h b/tinyusb/hw/bsp/stm32h7/boards/stm32h743eval/board.h new file mode 100755 index 00000000..ab263d2b --- /dev/null +++ b/tinyusb/hw/bsp/stm32h7/boards/stm32h743eval/board.h @@ -0,0 +1,132 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2021, Ha Thach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#ifndef BOARD_H_ +#define BOARD_H_ + +#ifdef __cplusplus + extern "C" { +#endif + +#define LED_PORT GPIOA +#define LED_PIN GPIO_PIN_4 +#define LED_STATE_ON 1 + +// Tamper push-button +#define BUTTON_PORT GPIOC +#define BUTTON_PIN GPIO_PIN_13 +#define BUTTON_STATE_ACTIVE 0 + +// Need to change jumper setting J7 and J8 from RS-232 to STLink +#define UART_DEV USART1 +#define UART_CLK_EN __HAL_RCC_USART1_CLK_ENABLE +#define UART_GPIO_PORT GPIOB +#define UART_GPIO_AF GPIO_AF4_USART1 +#define UART_TX_PIN GPIO_PIN_14 +#define UART_RX_PIN GPIO_PIN_15 + +// VBUS Sense detection +#define OTG_FS_VBUS_SENSE 1 +#define OTG_HS_VBUS_SENSE 0 + +//--------------------------------------------------------------------+ +// RCC Clock +//--------------------------------------------------------------------+ +static inline void board_stm32h7_clock_init(void) +{ + RCC_ClkInitTypeDef RCC_ClkInitStruct; + RCC_OscInitTypeDef RCC_OscInitStruct; + RCC_PeriphCLKInitTypeDef PeriphClkInitStruct; + + /*!< Supply configuration update enable */ + HAL_PWREx_ConfigSupply(PWR_LDO_SUPPLY); + + /* The voltage scaling allows optimizing the power consumption when the device is + clocked below the maximum system frequency, to update the voltage scaling value + regarding system frequency refer to product datasheet. */ + __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1); + + while ((PWR->D3CR & (PWR_D3CR_VOSRDY)) != PWR_D3CR_VOSRDY) {} + + /* Enable HSE Oscillator and activate PLL with HSE as source */ + RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE; + RCC_OscInitStruct.HSEState = RCC_HSE_ON; + RCC_OscInitStruct.HSIState = RCC_HSI_OFF; + RCC_OscInitStruct.CSIState = RCC_CSI_OFF; + RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON; + RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE; + + /* PLL1 for System Clock */ + RCC_OscInitStruct.PLL.PLLM = 5; + RCC_OscInitStruct.PLL.PLLN = 160; + RCC_OscInitStruct.PLL.PLLFRACN = 0; + RCC_OscInitStruct.PLL.PLLP = 2; + RCC_OscInitStruct.PLL.PLLR = 2; + RCC_OscInitStruct.PLL.PLLQ = 4; + + RCC_OscInitStruct.PLL.PLLVCOSEL = RCC_PLL1VCOMEDIUM; + RCC_OscInitStruct.PLL.PLLRGE = RCC_PLL1VCIRANGE_2; + HAL_RCC_OscConfig(&RCC_OscInitStruct); + + /* PLL3 for USB Clock */ + PeriphClkInitStruct.PLL3.PLL3M = 25; + PeriphClkInitStruct.PLL3.PLL3N = 336; + PeriphClkInitStruct.PLL3.PLL3FRACN = 0; + PeriphClkInitStruct.PLL3.PLL3P = 2; + PeriphClkInitStruct.PLL3.PLL3R = 2; + PeriphClkInitStruct.PLL3.PLL3Q = 7; + + PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_USB; + PeriphClkInitStruct.UsbClockSelection = RCC_USBCLKSOURCE_PLL3; + HAL_RCCEx_PeriphCLKConfig(&PeriphClkInitStruct); + + /* Select PLL as system clock source and configure bus clocks dividers */ + RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_D1PCLK1 | RCC_CLOCKTYPE_PCLK1 | \ + RCC_CLOCKTYPE_PCLK2 | RCC_CLOCKTYPE_D3PCLK1); + + RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; + RCC_ClkInitStruct.SYSCLKDivider = RCC_SYSCLK_DIV1; + RCC_ClkInitStruct.AHBCLKDivider = RCC_HCLK_DIV2; + RCC_ClkInitStruct.APB1CLKDivider = RCC_APB1_DIV2; + RCC_ClkInitStruct.APB2CLKDivider = RCC_APB2_DIV2; + RCC_ClkInitStruct.APB3CLKDivider = RCC_APB3_DIV1; + HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_4); + + /*activate CSI clock mondatory for I/O Compensation Cell*/ + __HAL_RCC_CSI_ENABLE() ; + + /* Enable SYSCFG clock mondatory for I/O Compensation Cell */ + __HAL_RCC_SYSCFG_CLK_ENABLE() ; + + /* Enables the I/O Compensation Cell */ + HAL_EnableCompensationCell(); +} + +#ifdef __cplusplus + } +#endif + +#endif |