1 files changed, 116 insertions, 0 deletions
diff --git a/tinyusb/hw/bsp/stm32h7/boards/stm32h743nucleo/board.h b/tinyusb/hw/bsp/stm32h7/boards/stm32h743nucleo/board.h
new file mode 100755
index 00000000..3a31783a
--- /dev/null
+++ b/tinyusb/hw/bsp/stm32h7/boards/stm32h743nucleo/board.h
@@ -0,0 +1,116 @@
+/*
+ * The MIT License (MIT)
+ *
+ * Copyright (c) 2021, Ha Thach (tinyusb.org)
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy
+ * of this software and associated documentation files (the "Software"), to deal
+ * in the Software without restriction, including without limitation the rights
+ * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ * copies of the Software, and to permit persons to whom the Software is
+ * furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ * THE SOFTWARE.
+ *
+ * This file is part of the TinyUSB stack.
+ */
+
+#ifndef BOARD_H_
+#define BOARD_H_
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+#define LED_PORT              GPIOB
+#define LED_PIN               GPIO_PIN_0
+#define LED_STATE_ON          1
+
+#define BUTTON_PORT           GPIOC
+#define BUTTON_PIN            GPIO_PIN_13
+#define BUTTON_STATE_ACTIVE   1
+
+#define UART_DEV              USART3
+#define UART_CLK_EN           __HAL_RCC_USART3_CLK_ENABLE
+#define UART_GPIO_PORT        GPIOD
+#define UART_GPIO_AF          GPIO_AF7_USART3
+#define UART_TX_PIN           GPIO_PIN_8
+#define UART_RX_PIN           GPIO_PIN_9
+
+// VBUS Sense detection
+#define OTG_FS_VBUS_SENSE     1
+#define OTG_HS_VBUS_SENSE     0
+
+//--------------------------------------------------------------------+
+// RCC Clock
+//--------------------------------------------------------------------+
+static inline void board_stm32h7_clock_init(void)
+{
+  RCC_ClkInitTypeDef RCC_ClkInitStruct;
+  RCC_OscInitTypeDef RCC_OscInitStruct;
+
+  /* The PWR block is always enabled on the H7 series- there is no clock
+     enable. For now, use the default VOS3 scale mode (lowest) and limit clock
+     frequencies to avoid potential current draw problems from bus
+     power when using the max clock speeds throughout the chip. */
+
+  /* Enable HSE Oscillator and activate PLL1 with HSE as source */
+  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
+  RCC_OscInitStruct.HSEState = RCC_HSE_ON;
+  RCC_OscInitStruct.HSIState = RCC_HSI_OFF;
+  RCC_OscInitStruct.CSIState = RCC_CSI_OFF;
+  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+  RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
+  RCC_OscInitStruct.PLL.PLLM = HSE_VALUE/1000000;
+  RCC_OscInitStruct.PLL.PLLN = 336;
+  RCC_OscInitStruct.PLL.PLLP = 2;
+  RCC_OscInitStruct.PLL.PLLQ = 7;
+  RCC_OscInitStruct.PLL.PLLR = 2; /* Unused */
+  RCC_OscInitStruct.PLL.PLLRGE = RCC_PLL1VCIRANGE_0;
+  RCC_OscInitStruct.PLL.PLLVCOSEL = RCC_PLL1VCOMEDIUM;
+  RCC_OscInitStruct.PLL.PLLFRACN = 0;
+  HAL_RCC_OscConfig(&RCC_OscInitStruct);
+
+  RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | \
+    RCC_CLOCKTYPE_D1PCLK1 | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2 | \
+    RCC_CLOCKTYPE_D3PCLK1);
+  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+  RCC_ClkInitStruct.SYSCLKDivider = RCC_SYSCLK_DIV1;
+  RCC_ClkInitStruct.AHBCLKDivider = RCC_HCLK_DIV1;
+
+  /* Unlike on the STM32F4 family, it appears the maximum APB frequencies are
+     device-dependent- 120 MHz for this board according to Figure 2 of
+     the datasheet. Dividing by half will be safe for now. */
+  RCC_ClkInitStruct.APB3CLKDivider = RCC_APB3_DIV2;
+  RCC_ClkInitStruct.APB1CLKDivider = RCC_APB1_DIV2;
+  RCC_ClkInitStruct.APB2CLKDivider = RCC_APB2_DIV2;
+  RCC_ClkInitStruct.APB4CLKDivider = RCC_APB4_DIV2;
+
+  /* 4 wait states required for 168MHz and VOS3. */
+  HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_4);
+
+  /* Like on F4, on H7, USB's actual peripheral clock and bus clock are
+     separate. However, the main system PLL (PLL1) doesn't have a direct
+     connection to the USB peripheral clock to generate 48 MHz, so we do this
+     dance. This will connect PLL1's Q output to the USB peripheral clock. */
+  RCC_PeriphCLKInitTypeDef RCC_PeriphCLKInitStruct;
+
+  RCC_PeriphCLKInitStruct.PeriphClockSelection = RCC_PERIPHCLK_USB;
+  RCC_PeriphCLKInitStruct.UsbClockSelection = RCC_USBCLKSOURCE_PLL;
+  HAL_RCCEx_PeriphCLKConfig(&RCC_PeriphCLKInitStruct);
+}
+
+#ifdef __cplusplus
+ }
+#endif
+
+#endif