1 files changed, 0 insertions, 64 deletions
diff --git a/tinyusb/hw/bsp/waveshare_openh743i/board.mk b/tinyusb/hw/bsp/waveshare_openh743i/board.mk
deleted file mode 100755
index 721df1bd..00000000
--- a/tinyusb/hw/bsp/waveshare_openh743i/board.mk
+++ /dev/null
@@ -1,64 +0,0 @@
-UF2_FAMILY_ID = 0x6db66082
-ST_FAMILY = h7
-DEPS_SUBMODULES += lib/CMSIS_5 hw/mcu/st/cmsis_device_$(ST_FAMILY) hw/mcu/st/stm32$(ST_FAMILY)xx_hal_driver
-
-ST_CMSIS = hw/mcu/st/cmsis_device_$(ST_FAMILY)
-ST_HAL_DRIVER = hw/mcu/st/stm32$(ST_FAMILY)xx_hal_driver
-
-# Default is HS port
-PORT ?= 1
-
-SRC_S += $(ST_CMSIS)/Source/Templates/gcc/startup_stm32h743xx.s
-LD_FILE = $(BOARD_PATH)/STM32H743IITX_FLASH.ld
-
-CFLAGS += \
-  -flto \
-  -mthumb \
-  -mabi=aapcs \
-  -mcpu=cortex-m7 \
-  -mfloat-abi=hard \
-  -mfpu=fpv5-d16 \
-  -nostdlib -nostartfiles \
-  -DCFG_TUSB_MCU=OPT_MCU_STM32H7 \
-	-DBOARD_DEVICE_RHPORT_NUM=$(PORT) \
-  -DSTM32H743xx \
-  -DHSE_VALUE=8000000
-
-ifeq ($(PORT), 1)
-  CFLAGS += -DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_HIGH_SPEED
-  $(info "PORT1 High Speed")
-else
-  $(info "PORT0 Full Speed")
-endif
-
-# suppress warning caused by vendor mcu driver
-CFLAGS += -Wno-error=maybe-uninitialized -Wno-error=cast-align
-
-# All source paths should be relative to the top level.
-SRC_C += \
-	src/portable/st/synopsys/dcd_synopsys.c \
-	$(ST_CMSIS)/Source/Templates/system_stm32$(ST_FAMILY)xx.c \
-	$(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal.c \
-	$(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_cortex.c \
-	$(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_rcc.c \
-	$(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_rcc_ex.c \
-	$(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_gpio.c \
-	$(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_uart.c \
-	$(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_pwr_ex.c \
-  $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_tim.c \
-  $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_tim_ex.c
-
-INC += \
-	$(TOP)/$(BOARD_PATH) \
-	$(TOP)/lib/CMSIS_5/CMSIS/Core/Include \
-	$(TOP)/$(ST_CMSIS)/Include \
-	$(TOP)/$(ST_HAL_DRIVER)/Inc
-
-# For freeRTOS port source
-FREERTOS_PORT = ARM_CM7/r0p1
-
-# For flash-jlink target
-JLINK_DEVICE = stm32h743ii
-
-# flash target using jlink
-flash: flash-jlink
-\ No newline at end of file