diff options
Diffstat (limited to 'tinyusb/hw/bsp/waveshare_openh743i')
| -rwxr-xr-x | tinyusb/hw/bsp/waveshare_openh743i/STM32H743IITX_FLASH.ld | 175 | ||||
| -rwxr-xr-x | tinyusb/hw/bsp/waveshare_openh743i/board.c | 495 | ||||
| -rwxr-xr-x | tinyusb/hw/bsp/waveshare_openh743i/board.mk | 64 | ||||
| -rwxr-xr-x | tinyusb/hw/bsp/waveshare_openh743i/stm32h7xx_hal_conf.h | 483 |
4 files changed, 1217 insertions, 0 deletions
diff --git a/tinyusb/hw/bsp/waveshare_openh743i/STM32H743IITX_FLASH.ld b/tinyusb/hw/bsp/waveshare_openh743i/STM32H743IITX_FLASH.ld new file mode 100755 index 00000000..73d2dedb --- /dev/null +++ b/tinyusb/hw/bsp/waveshare_openh743i/STM32H743IITX_FLASH.ld @@ -0,0 +1,175 @@ +/* +****************************************************************************** +** +** File : LinkerScript.ld +** +** Author : STM32CubeIDE +** +** Abstract : Linker script for STM32H7 series +** 2048Kbytes FLASH and 192Kbytes RAM +** +** Set heap size, stack size and stack location according +** to application requirements. +** +** Set memory bank area and size if external memory is used. +** +** Target : STMicroelectronics STM32 +** +** Distribution: The file is distributed as is, without any warranty +** of any kind. +** +***************************************************************************** +** @attention +** +** Copyright (c) 2019 STMicroelectronics. +** All rights reserved. +** +** This software component is licensed by ST under BSD 3-Clause license, +** the "License"; You may not use this file except in compliance with the +** License. You may obtain a copy of the License at: +** opensource.org/licenses/BSD-3-Clause +** +**************************************************************************** +*/ + +/* Entry Point */ +ENTRY(Reset_Handler) + +/* Highest address of the user mode stack */ +_estack = 0x20020000; /* end of RAM */ +/* Generate a link error if heap and stack don't fit into RAM */ +_Min_Heap_Size = 0x2000 ; /* required amount of heap */ +_Min_Stack_Size = 0x2000 ; /* required amount of stack */ + +/* Specify the memory areas */ +MEMORY +{ + FLASH (rx) : ORIGIN = 0x08000000, LENGTH = 2048K + RAM (xrw) : ORIGIN = 0x20000000, LENGTH = 128K + RAM_D1 (xrw) : ORIGIN = 0x24000000, LENGTH = 512K + RAM_D2 (xrw) : ORIGIN = 0x30000000, LENGTH = 288K + RAM_D3 (xrw) : ORIGIN = 0x38000000, LENGTH = 64K + ITCMRAM (xrw) : ORIGIN = 0x00000000, LENGTH = 64K +} + +/* Define output sections */ +SECTIONS +{ + /* The startup code goes first into FLASH */ + .isr_vector : + { + . = ALIGN(4); + KEEP(*(.isr_vector)) /* Startup code */ + . = ALIGN(4); + } >FLASH + + /* The program code and other data goes into FLASH */ + .text : + { + . = ALIGN(4); + *(.text) /* .text sections (code) */ + *(.text*) /* .text* sections (code) */ + *(.glue_7) /* glue arm to thumb code */ + *(.glue_7t) /* glue thumb to arm code */ + *(.eh_frame) + + KEEP (*(.init)) + KEEP (*(.fini)) + + . = ALIGN(4); + _etext = .; /* define a global symbols at end of code */ + } >FLASH + + /* Constant data goes into FLASH */ + .rodata : + { + . = ALIGN(4); + *(.rodata) /* .rodata sections (constants, strings, etc.) */ + *(.rodata*) /* .rodata* sections (constants, strings, etc.) */ + . = ALIGN(4); + } >FLASH + + .ARM.extab : { *(.ARM.extab* .gnu.linkonce.armextab.*) } >FLASH + .ARM : { + __exidx_start = .; + *(.ARM.exidx*) + __exidx_end = .; + } >FLASH + + .preinit_array : + { + PROVIDE_HIDDEN (__preinit_array_start = .); + KEEP (*(.preinit_array*)) + PROVIDE_HIDDEN (__preinit_array_end = .); + } >FLASH + .init_array : + { + PROVIDE_HIDDEN (__init_array_start = .); + KEEP (*(SORT(.init_array.*))) + KEEP (*(.init_array*)) + PROVIDE_HIDDEN (__init_array_end = .); + } >FLASH + .fini_array : + { + PROVIDE_HIDDEN (__fini_array_start = .); + KEEP (*(SORT(.fini_array.*))) + KEEP (*(.fini_array*)) + PROVIDE_HIDDEN (__fini_array_end = .); + } >FLASH + + /* used by the startup to initialize data */ + _sidata = LOADADDR(.data); + + /* Initialized data sections goes into RAM, load LMA copy after code */ + .data : + { + . = ALIGN(4); + _sdata = .; /* create a global symbol at data start */ + *(.data) /* .data sections */ + *(.data*) /* .data* sections */ + *(.RamFunc) /* .RamFunc sections */ + *(.RamFunc*) /* .RamFunc* sections */ + + . = ALIGN(4); + _edata = .; /* define a global symbol at data end */ + } >RAM AT> FLASH + + /* Uninitialized data section */ + . = ALIGN(4); + .bss : + { + /* This is used by the startup in order to initialize the .bss secion */ + _sbss = .; /* define a global symbol at bss start */ + __bss_start__ = _sbss; + *(.bss) + *(.bss*) + *(COMMON) + + . = ALIGN(4); + _ebss = .; /* define a global symbol at bss end */ + __bss_end__ = _ebss; + } >RAM + + /* User_heap_stack section, used to check that there is enough RAM left */ + ._user_heap_stack : + { + . = ALIGN(8); + PROVIDE ( end = . ); + PROVIDE ( _end = . ); + . = . + _Min_Heap_Size; + . = . + _Min_Stack_Size; + . = ALIGN(8); + } >RAM + + /* Remove information from the standard libraries */ + /DISCARD/ : + { + libc.a ( * ) + libm.a ( * ) + libgcc.a ( * ) + } + + .ARM.attributes 0 : { *(.ARM.attributes) } +} + + diff --git a/tinyusb/hw/bsp/waveshare_openh743i/board.c b/tinyusb/hw/bsp/waveshare_openh743i/board.c new file mode 100755 index 00000000..4468c066 --- /dev/null +++ b/tinyusb/hw/bsp/waveshare_openh743i/board.c @@ -0,0 +1,495 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2019 + * Benjamin Evans + * William D. Jones (thor0505@comcast.net), + * Ha Thach (tinyusb.org) + * Uwe Bonnes (bon@elektron.ikp.physik.tu-darmstadt.de + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#include "stm32h7xx_hal.h" +#include "stm32h7xx_hal_tim.h" +#include "bsp/board.h" + + +/* ** BOARD SETUP ** + * + * NOTE: This board has bad signal integrity so you may experience some problems. + * This setup assumes you have an openh743i-c Core and breakout board. For the HS + * examples it also assumes you have a waveshare USB3300 breakout board plugged + * into the ULPI PMOD header on the openh743i-c. + * + * UART Debugging: + * Due to pin conflicts in the HS configuration, this BSP uses USART3 (PD8, PD9). + * As such, you won't be able to use the UART to USB converter on board and will + * require an external UART to USB converter. You could use the waveshare FT232 + * USB UART Board (micro) but any 3.3V UART to USB converter will be fine. + * + * Fullspeed: + * If VBUS sense is enabled, ensure the PA9-VBUS jumper is connected on the core + * board. Connect the PB6 jumper for the LED and the Wakeup - PA0 jumper for the + * button. Connect the USB cable to the USB connector on the core board. + * + * High Speed: + * Remove all jumpers from the openh743i-c (especially the USART1 jumpers as the + * pins conflict). Connect the PB6 jumper for the LED and the Wakeup - PA0 + * jumper for the button. + * + * The reset pin on the ULPI PMOD port is not connected to the MCU. You'll need + * to solder a wire from the RST pin on the USB3300 to a pin of your choosing on + * the openh743i-c board (this example assumes you've used PD14 as specified with + * the ULPI_RST_PORT and ULPI_RST_PIN defines below). + * + * Preferably power the board using the external 5VDC jack. Connect the USB cable + * to the USB connector on the ULPI board. Adjust delays in this file as required. + * + * If you're having trouble, ask a question on the tinyUSB Github Discussion boards. + * + * Have fun! + * +*/ + +//--------------------------------------------------------------------+ +// BOARD DEFINES +//--------------------------------------------------------------------+ + +//LED Pin +#define LED_PORT GPIOB +#define LED_PIN GPIO_PIN_6 +#define LED_STATE_ON 1 + +//ULPI PHY reset pin +#define ULPI_RST_PORT GPIOD +#define ULPI_RST_PIN GPIO_PIN_14 + +// Tamper push-button +#define BUTTON_PORT GPIOA +#define BUTTON_PIN GPIO_PIN_0 +#define BUTTON_STATE_ACTIVE 1 + +// Need external UART to USB converter as USART1 pins conflict with HS ULPI pins +#define UART_DEV USART3 +#define UART_CLK_EN __HAL_RCC_USART3_CLK_ENABLE +#define UART_GPIO_PORT GPIOD +#define UART_GPIO_AF GPIO_AF7_USART3 +#define UART_TX_PIN GPIO_PIN_8 +#define UART_RX_PIN GPIO_PIN_9 + +// VBUS Sense detection +#define OTG_FS_VBUS_SENSE 1 +#define OTG_HS_VBUS_SENSE 0 + + +//--------------------------------------------------------------------+ +// MACRO TYPEDEF CONSTANT ENUM +//--------------------------------------------------------------------+ + +UART_HandleTypeDef uartHandle; +TIM_HandleTypeDef tim2Handle; + + +//--------------------------------------------------------------------+ +// Forward USB interrupt events to TinyUSB IRQ Handler +//--------------------------------------------------------------------+ + +// Despite being call USB2_OTG +// OTG_FS is marked as RHPort0 by TinyUSB to be consistent across stm32 port +void OTG_FS_IRQHandler(void) +{ + tud_int_handler(0); +} + +// Despite being call USB2_OTG +// OTG_HS is marked as RHPort1 by TinyUSB to be consistent across stm32 port +void OTG_HS_IRQHandler(void) +{ + tud_int_handler(1); +} + + +//--------------------------------------------------------------------+ +// RCC Clock +//--------------------------------------------------------------------+ +static inline void board_stm32h7_clock_init(void) +{ + RCC_OscInitTypeDef RCC_OscInitStruct = {0}; + RCC_ClkInitTypeDef RCC_ClkInitStruct = {0}; + RCC_PeriphCLKInitTypeDef PeriphClkInitStruct = {0}; + + __HAL_RCC_SYSCFG_CLK_ENABLE(); + + // Supply configuration update enable + HAL_PWREx_ConfigSupply(PWR_LDO_SUPPLY); + + // Configure the main internal regulator output voltage + __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE0); + + while (!__HAL_PWR_GET_FLAG(PWR_FLAG_VOSRDY)) + { + } + // Macro to configure the PLL clock source + __HAL_RCC_PLL_PLLSOURCE_CONFIG(RCC_PLLSOURCE_HSE); + + // Initializes the RCC Oscillators according to the specified parameters in the RCC_OscInitTypeDef structure. + RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE; + RCC_OscInitStruct.HSEState = RCC_HSE_ON; + RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON; + RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE; + RCC_OscInitStruct.PLL.PLLM = 2; + RCC_OscInitStruct.PLL.PLLN = 240; + RCC_OscInitStruct.PLL.PLLP = 2; + RCC_OscInitStruct.PLL.PLLQ = 2; + RCC_OscInitStruct.PLL.PLLR = 2; + RCC_OscInitStruct.PLL.PLLRGE = RCC_PLL1VCIRANGE_2; + RCC_OscInitStruct.PLL.PLLVCOSEL = RCC_PLL1VCOWIDE; + RCC_OscInitStruct.PLL.PLLFRACN = 0; + HAL_RCC_OscConfig(&RCC_OscInitStruct); + + PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_USB | RCC_PERIPHCLK_USART3; + PeriphClkInitStruct.PLL3.PLL3M = 8; + PeriphClkInitStruct.PLL3.PLL3N = 336; + PeriphClkInitStruct.PLL3.PLL3P = 2; + PeriphClkInitStruct.PLL3.PLL3Q = 7; + PeriphClkInitStruct.PLL3.PLL3R = 2; + PeriphClkInitStruct.PLL3.PLL3RGE = RCC_PLL3VCIRANGE_0; + PeriphClkInitStruct.PLL3.PLL3VCOSEL = RCC_PLL3VCOWIDE; + PeriphClkInitStruct.PLL3.PLL3FRACN = 0; + PeriphClkInitStruct.Usart234578ClockSelection = RCC_USART234578CLKSOURCE_PLL3; + PeriphClkInitStruct.UsbClockSelection = RCC_USBCLKSOURCE_PLL3; + HAL_RCCEx_PeriphCLKConfig(&PeriphClkInitStruct); + + // Initializes the CPU, AHB and APB buses clocks + RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2 | RCC_CLOCKTYPE_D3PCLK1 | RCC_CLOCKTYPE_D1PCLK1; + RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; + RCC_ClkInitStruct.SYSCLKDivider = RCC_SYSCLK_DIV1; + RCC_ClkInitStruct.AHBCLKDivider = RCC_HCLK_DIV2; + RCC_ClkInitStruct.APB3CLKDivider = RCC_APB3_DIV2; + RCC_ClkInitStruct.APB1CLKDivider = RCC_APB1_DIV2; + RCC_ClkInitStruct.APB2CLKDivider = RCC_APB2_DIV2; + RCC_ClkInitStruct.APB4CLKDivider = RCC_APB4_DIV2; + HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2); + + __HAL_RCC_CSI_ENABLE(); + + // Enable SYSCFG clock mondatory for I/O Compensation Cell + __HAL_RCC_SYSCFG_CLK_ENABLE(); + + // Enables the I/O Compensation Cell + HAL_EnableCompensationCell(); + + // Enable voltage detector + HAL_PWREx_EnableUSBVoltageDetector(); + + return; +} + + +//--------------------------------------------------------------------+ +// Timer implementation for board delay +// This should be OS safe and doesn't require the scheduler to be running +//--------------------------------------------------------------------+ +static void init_timer(void) +{ + TIM_ClockConfigTypeDef sClockSourceConfig = {0}; + + __HAL_RCC_TIM2_CLK_ENABLE(); + + //Assuming timer clock is running at 260Mhz this should configure the timer counter to 1000Hz + tim2Handle.Instance = TIM2; + tim2Handle.Init.Prescaler = 60000U - 1U; + tim2Handle.Init.CounterMode = TIM_COUNTERMODE_UP; + tim2Handle.Init.Period = 0xFFFFFFFFU; + tim2Handle.Init.ClockDivision = TIM_CLOCKDIVISION_DIV4; + tim2Handle.Init.AutoReloadPreload = TIM_AUTORELOAD_PRELOAD_DISABLE; + HAL_TIM_Base_Init(&tim2Handle); + + sClockSourceConfig.ClockSource = TIM_CLOCKSOURCE_INTERNAL; + HAL_TIM_ConfigClockSource(&tim2Handle, &sClockSourceConfig); + + //Start the timer + HAL_TIM_Base_Start(&tim2Handle); + + return; +} + + +// Custom board delay implementation using timer ticks +static inline void timer_board_delay(uint32_t ms) +{ + uint32_t startMs = __HAL_TIM_GET_COUNTER(&tim2Handle); + while ((__HAL_TIM_GET_COUNTER(&tim2Handle) - startMs) < ms) + { + asm("nop"); //do nothing + } +} + + +//Board initialisation +void board_init(void) +{ + GPIO_InitTypeDef GPIO_InitStruct; + + // Init clocks + board_stm32h7_clock_init(); + + // Init timer for delays + init_timer(); + + //Disable systick for now + //If using an RTOS and the systick interrupt fires without the scheduler running you might have an issue + //Because this init code now introduces delays, the systick should be disabled until after board init + SysTick->CTRL &= ~1U; + + // Enable GPIO clocks + __HAL_RCC_GPIOA_CLK_ENABLE(); + __HAL_RCC_GPIOB_CLK_ENABLE(); + __HAL_RCC_GPIOC_CLK_ENABLE(); + __HAL_RCC_GPIOD_CLK_ENABLE(); + __HAL_RCC_GPIOH_CLK_ENABLE(); + __HAL_RCC_GPIOI_CLK_ENABLE(); + + // Enable UART Clock + UART_CLK_EN(); + +#if CFG_TUSB_OS == OPT_OS_FREERTOS + // If freeRTOS is used, IRQ priority is limit by max syscall ( smaller is higher ) + NVIC_SetPriority(OTG_FS_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY); + NVIC_SetPriority(OTG_HS_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY); +#endif + + // LED + GPIO_InitStruct.Pin = LED_PIN; + GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP; + GPIO_InitStruct.Pull = GPIO_PULLUP; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; + HAL_GPIO_Init(LED_PORT, &GPIO_InitStruct); + + // PHY RST Pin + GPIO_InitStruct.Pin = ULPI_RST_PIN; + GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW; + HAL_GPIO_Init(ULPI_RST_PORT, &GPIO_InitStruct); + HAL_GPIO_WritePin(ULPI_RST_PORT, ULPI_RST_PIN, 0U); + + // Button + GPIO_InitStruct.Pin = BUTTON_PIN; + GPIO_InitStruct.Mode = GPIO_MODE_INPUT; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; + HAL_GPIO_Init(BUTTON_PORT, &GPIO_InitStruct); + + // Uart + GPIO_InitStruct.Pin = UART_TX_PIN | UART_RX_PIN; + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_PULLUP; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH; + GPIO_InitStruct.Alternate = UART_GPIO_AF; + HAL_GPIO_Init(UART_GPIO_PORT, &GPIO_InitStruct); + + uartHandle.Instance = UART_DEV; + uartHandle.Init.BaudRate = CFG_BOARD_UART_BAUDRATE; + uartHandle.Init.WordLength = UART_WORDLENGTH_8B; + uartHandle.Init.StopBits = UART_STOPBITS_1; + uartHandle.Init.Parity = UART_PARITY_NONE; + uartHandle.Init.HwFlowCtl = UART_HWCONTROL_NONE; + uartHandle.Init.Mode = UART_MODE_TX_RX; + uartHandle.Init.OverSampling = UART_OVERSAMPLING_16; + HAL_UART_Init(&uartHandle); + +#if BOARD_DEVICE_RHPORT_NUM == 0 + //Full Speed + + // Configure DM DP Pins + GPIO_InitStruct.Pin = GPIO_PIN_11 | GPIO_PIN_12; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Alternate = GPIO_AF10_OTG2_HS; + HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); + + // This for ID line debug + GPIO_InitStruct.Pin = GPIO_PIN_10; + GPIO_InitStruct.Mode = GPIO_MODE_AF_OD; + GPIO_InitStruct.Pull = GPIO_PULLUP; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; + GPIO_InitStruct.Alternate = GPIO_AF10_OTG2_HS; + HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); + + __HAL_RCC_USB2_OTG_FS_CLK_ENABLE(); + +#if OTG_FS_VBUS_SENSE + // Configure VBUS Pin + GPIO_InitStruct.Pin = GPIO_PIN_9; + GPIO_InitStruct.Mode = GPIO_MODE_INPUT; + GPIO_InitStruct.Pull = GPIO_NOPULL; + HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); + + // Enable VBUS sense (B device) via pin PA9 + USB_OTG_FS->GCCFG |= USB_OTG_GCCFG_VBDEN; +#else + // Disable VBUS sense (B device) via pin PA9 + USB_OTG_FS->GCCFG &= ~USB_OTG_GCCFG_VBDEN; + + // B-peripheral session valid override enable + USB_OTG_FS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOEN; + USB_OTG_FS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOVAL; +#endif // vbus sense + +#elif BOARD_DEVICE_RHPORT_NUM == 1 + //High Speed + + /**USB_OTG_HS GPIO Configuration + PC0 ------> USB_OTG_HS_ULPI_STP + PC2_C ------> USB_OTG_HS_ULPI_DIR + PC3_C ------> USB_OTG_HS_ULPI_NXT + PA3 ------> USB_OTG_HS_ULPI_D0 + PA5 ------> USB_OTG_HS_ULPI_CK + PB1 ------> USB_OTG_HS_ULPI_D2 + PB10 ------> USB_OTG_HS_ULPI_D3 + PB11 ------> USB_OTG_HS_ULPI_D4 + PB12 ------> USB_OTG_HS_ULPI_D5 + PB13 ------> USB_OTG_HS_ULPI_D6 + PB5 ------> USB_OTG_HS_ULPI_D7 + */ + + GPIO_InitStruct.Pin = GPIO_PIN_0 | GPIO_PIN_2 | GPIO_PIN_3; + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH; + GPIO_InitStruct.Alternate = GPIO_AF10_OTG2_HS; + HAL_GPIO_Init(GPIOC, &GPIO_InitStruct); + + GPIO_InitStruct.Pin = GPIO_PIN_3 | GPIO_PIN_5; + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH; + GPIO_InitStruct.Alternate = GPIO_AF10_OTG2_HS; + HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); + + GPIO_InitStruct.Pin = GPIO_PIN_0 | GPIO_PIN_1 | GPIO_PIN_10 | GPIO_PIN_11 | GPIO_PIN_12 | GPIO_PIN_13 | GPIO_PIN_5; + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH; + GPIO_InitStruct.Alternate = GPIO_AF10_OTG2_HS; + HAL_GPIO_Init(GPIOB, &GPIO_InitStruct); + + // Peripheral clock enable + __HAL_RCC_USB_OTG_HS_CLK_ENABLE(); + __HAL_RCC_USB_OTG_HS_ULPI_CLK_ENABLE(); + +#if OTG_HS_VBUS_SENSE +#error OTG HS VBUS Sense enabled is not implemented +#else + // No VBUS sense + USB_OTG_HS->GCCFG &= ~USB_OTG_GCCFG_VBDEN; + + // B-peripheral session valid override enable + USB_OTG_HS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOEN; + USB_OTG_HS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOVAL; +#endif + + // Force device mode + USB_OTG_HS->GUSBCFG &= ~USB_OTG_GUSBCFG_FHMOD; + USB_OTG_HS->GUSBCFG |= USB_OTG_GUSBCFG_FDMOD; + + //Reset the PHY - Change the delays as you see fit + timer_board_delay(5U); //Delay 5ms + HAL_GPIO_WritePin(ULPI_RST_PORT, ULPI_RST_PIN, 1U); + timer_board_delay(20U); //Delay 20ms + HAL_GPIO_WritePin(ULPI_RST_PORT, ULPI_RST_PIN, 0U); + timer_board_delay(20U); //Delay 20ms + +#endif // rhport = 1 + + //Disable the timer used for delays + HAL_TIM_Base_Stop(&tim2Handle); + __HAL_RCC_TIM2_CLK_DISABLE(); + + // Configure systick 1ms tick timer + SysTick_Config(SystemCoreClock / 1000); + + //Enable systick + SysTick->CTRL |= ~1U; + + return; +} + + +//--------------------------------------------------------------------+ +// Board porting API +//--------------------------------------------------------------------+ +void board_led_write(bool state) +{ + HAL_GPIO_WritePin(LED_PORT, LED_PIN, state ? LED_STATE_ON : (1 - LED_STATE_ON)); +} + + +uint32_t board_button_read(void) +{ + return (BUTTON_STATE_ACTIVE == HAL_GPIO_ReadPin(BUTTON_PORT, BUTTON_PIN)) ? 1 : 0; +} + + +int board_uart_read(uint8_t *buf, int len) +{ + (void)buf; + (void)len; + return 0; +} + + +int board_uart_write(void const *buf, int len) +{ + HAL_UART_Transmit(&uartHandle, (uint8_t *)buf, len, 0xffff); + return len; +} + + +#if CFG_TUSB_OS == OPT_OS_NONE +volatile uint32_t system_ticks = 0; +void SysTick_Handler(void) +{ + system_ticks++; +} + + +uint32_t board_millis(void) +{ + return system_ticks; +} +#endif + + +void HardFault_Handler(void) +{ + asm("bkpt"); +} + + +// Required by __libc_init_array in startup code if we are compiling using +// -nostdlib/-nostartfiles. +void _init(void) +{ +}
\ No newline at end of file diff --git a/tinyusb/hw/bsp/waveshare_openh743i/board.mk b/tinyusb/hw/bsp/waveshare_openh743i/board.mk new file mode 100755 index 00000000..721df1bd --- /dev/null +++ b/tinyusb/hw/bsp/waveshare_openh743i/board.mk @@ -0,0 +1,64 @@ +UF2_FAMILY_ID = 0x6db66082 +ST_FAMILY = h7 +DEPS_SUBMODULES += lib/CMSIS_5 hw/mcu/st/cmsis_device_$(ST_FAMILY) hw/mcu/st/stm32$(ST_FAMILY)xx_hal_driver + +ST_CMSIS = hw/mcu/st/cmsis_device_$(ST_FAMILY) +ST_HAL_DRIVER = hw/mcu/st/stm32$(ST_FAMILY)xx_hal_driver + +# Default is HS port +PORT ?= 1 + +SRC_S += $(ST_CMSIS)/Source/Templates/gcc/startup_stm32h743xx.s +LD_FILE = $(BOARD_PATH)/STM32H743IITX_FLASH.ld + +CFLAGS += \ + -flto \ + -mthumb \ + -mabi=aapcs \ + -mcpu=cortex-m7 \ + -mfloat-abi=hard \ + -mfpu=fpv5-d16 \ + -nostdlib -nostartfiles \ + -DCFG_TUSB_MCU=OPT_MCU_STM32H7 \ + -DBOARD_DEVICE_RHPORT_NUM=$(PORT) \ + -DSTM32H743xx \ + -DHSE_VALUE=8000000 + +ifeq ($(PORT), 1) + CFLAGS += -DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_HIGH_SPEED + $(info "PORT1 High Speed") +else + $(info "PORT0 Full Speed") +endif + +# suppress warning caused by vendor mcu driver +CFLAGS += -Wno-error=maybe-uninitialized -Wno-error=cast-align + +# All source paths should be relative to the top level. +SRC_C += \ + src/portable/st/synopsys/dcd_synopsys.c \ + $(ST_CMSIS)/Source/Templates/system_stm32$(ST_FAMILY)xx.c \ + $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal.c \ + $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_cortex.c \ + $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_rcc.c \ + $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_rcc_ex.c \ + $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_gpio.c \ + $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_uart.c \ + $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_pwr_ex.c \ + $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_tim.c \ + $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_tim_ex.c + +INC += \ + $(TOP)/$(BOARD_PATH) \ + $(TOP)/lib/CMSIS_5/CMSIS/Core/Include \ + $(TOP)/$(ST_CMSIS)/Include \ + $(TOP)/$(ST_HAL_DRIVER)/Inc + +# For freeRTOS port source +FREERTOS_PORT = ARM_CM7/r0p1 + +# For flash-jlink target +JLINK_DEVICE = stm32h743ii + +# flash target using jlink +flash: flash-jlink
\ No newline at end of file diff --git a/tinyusb/hw/bsp/waveshare_openh743i/stm32h7xx_hal_conf.h b/tinyusb/hw/bsp/waveshare_openh743i/stm32h7xx_hal_conf.h new file mode 100755 index 00000000..11d29ed6 --- /dev/null +++ b/tinyusb/hw/bsp/waveshare_openh743i/stm32h7xx_hal_conf.h @@ -0,0 +1,483 @@ +/** + ****************************************************************************** + * @file stm32h7xx_hal_conf_template.h + * @brief HAL configuration template file. + * This file should be copied to the application folder and renamed + * to stm32h7xx_hal_conf.h. + ****************************************************************************** + * @attention + * + * <h2><center>© COPYRIGHT(c) 2019 STMicroelectronics</center></h2> + * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32H7xx_HAL_CONF_H +#define __STM32H7xx_HAL_CONF_H + +#ifdef __cplusplus + extern "C" { +#endif + +/* Exported types ------------------------------------------------------------*/ +/* Exported constants --------------------------------------------------------*/ + +/* ########################## Module Selection ############################## */ +/** + * @brief This is the list of modules to be used in the HAL driver + */ +#define HAL_MODULE_ENABLED +#define HAL_ADC_MODULE_ENABLED +/* #define HAL_CEC_MODULE_ENABLED */ +/* #define HAL_COMP_MODULE_ENABLED */ +#define HAL_CORTEX_MODULE_ENABLED +/* #define HAL_CRC_MODULE_ENABLED */ +/* #define HAL_CRYP_MODULE_ENABLED */ +/* #define HAL_DAC_MODULE_ENABLED */ +/* #define HAL_DCMI_MODULE_ENABLED */ +/* #define HAL_DFSDM_MODULE_ENABLED */ +#define HAL_DMA_MODULE_ENABLED +/* #define HAL_DMA2D_MODULE_ENABLED */ +/* #define HAL_ETH_MODULE_ENABLED */ +/* #define HAL_EXTI_MODULE_ENABLED */ +/* #define HAL_FDCAN_MODULE_ENABLED */ +#define HAL_FLASH_MODULE_ENABLED +#define HAL_GPIO_MODULE_ENABLED +/* #define HAL_HASH_MODULE_ENABLED */ +/* #define HAL_HCD_MODULE_ENABLED */ +/* #define HAL_HRTIM_MODULE_ENABLED */ +/* #define HAL_HSEM_MODULE_ENABLED */ +/* #define HAL_I2C_MODULE_ENABLED */ +/* #define HAL_I2S_MODULE_ENABLED */ +/* #define HAL_IRDA_MODULE_ENABLED */ +/* #define HAL_IWDG_MODULE_ENABLED */ +/* #define HAL_JPEG_MODULE_ENABLED */ +/* #define HAL_LPTIM_MODULE_ENABLED */ +/* #define HAL_LTDC_MODULE_ENABLED */ +/* #define HAL_MDIOS_MODULE_ENABLED */ +/* #define HAL_MDMA_MODULE_ENABLED */ +/* #define HAL_MMC_MODULE_ENABLED */ +/* #define HAL_NAND_MODULE_ENABLED */ +/* #define HAL_NOR_MODULE_ENABLED */ +/* #define HAL_OPAMP_MODULE_ENABLED */ +/* #define HAL_PCD_MODULE_ENABLED */ +#define HAL_PWR_MODULE_ENABLED +/* #define HAL_QSPI_MODULE_ENABLED */ +/* #define HAL_RAMECC_MODULE_ENABLED */ +#define HAL_RCC_MODULE_ENABLED +/* #define HAL_RNG_MODULE_ENABLED */ +/* #define HAL_RTC_MODULE_ENABLED */ +/* #define HAL_SAI_MODULE_ENABLED */ +/* #define HAL_SD_MODULE_ENABLED */ +/* #define HAL_SDRAM_MODULE_ENABLED */ +/* #define HAL_SMARTCARD_MODULE_ENABLED */ +/* #define HAL_SMBUS_MODULE_ENABLED */ +/* #define HAL_SPDIFRX_MODULE_ENABLED */ +#define HAL_SPI_MODULE_ENABLED +/* #define HAL_SRAM_MODULE_ENABLED */ +/* #define HAL_SWPMI_MODULE_ENABLED */ +#define HAL_TIM_MODULE_ENABLED +#define HAL_UART_MODULE_ENABLED +/* #define HAL_USART_MODULE_ENABLED */ +/* #define HAL_WWDG_MODULE_ENABLED */ + +/* ########################## Oscillator Values adaptation ####################*/ +/** + * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. + * This value is used by the RCC HAL module to compute the system frequency + * (when HSE is used as system clock source, directly or through the PLL). + */ +#if !defined (HSE_VALUE) +//#define HSE_VALUE ((uint32_t)25000000) /*!< Value of the External oscillator in Hz */ +#error HSE_VALUE is not defined +#endif /* HSE_VALUE */ + +#if !defined (HSE_STARTUP_TIMEOUT) + #define HSE_STARTUP_TIMEOUT ((uint32_t)5000) /*!< Time out for HSE start up, in ms */ +#endif /* HSE_STARTUP_TIMEOUT */ + +/** + * @brief Internal oscillator (CSI) default value. + * This value is the default CSI value after Reset. + */ +#if !defined (CSI_VALUE) + #define CSI_VALUE ((uint32_t)4000000) /*!< Value of the Internal oscillator in Hz*/ +#endif /* CSI_VALUE */ + +/** + * @brief Internal High Speed oscillator (HSI) value. + * This value is used by the RCC HAL module to compute the system frequency + * (when HSI is used as system clock source, directly or through the PLL). + */ +#if !defined (HSI_VALUE) + #define HSI_VALUE ((uint32_t)64000000) /*!< Value of the Internal oscillator in Hz*/ +#endif /* HSI_VALUE */ + +/** + * @brief External Low Speed oscillator (LSE) value. + * This value is used by the UART, RTC HAL module to compute the system frequency + */ +#if !defined (LSE_VALUE) + #define LSE_VALUE ((uint32_t)32768) /*!< Value of the External oscillator in Hz*/ +#endif /* LSE_VALUE */ + + +#if !defined (LSE_STARTUP_TIMEOUT) + #define LSE_STARTUP_TIMEOUT ((uint32_t)5000) /*!< Time out for LSE start up, in ms */ +#endif /* LSE_STARTUP_TIMEOUT */ + +#if !defined (LSI_VALUE) + #define LSI_VALUE ((uint32_t)32000) /*!< LSI Typical Value in Hz*/ +#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz + The real value may vary depending on the variations + in voltage and temperature.*/ + +/** + * @brief External clock source for I2S peripheral + * This value is used by the I2S HAL module to compute the I2S clock source + * frequency, this source is inserted directly through I2S_CKIN pad. + */ +#if !defined (EXTERNAL_CLOCK_VALUE) + #define EXTERNAL_CLOCK_VALUE 12288000U /*!< Value of the External clock in Hz*/ +#endif /* EXTERNAL_CLOCK_VALUE */ + +/* Tip: To avoid modifying this file each time you need to use different HSE, + === you can define the HSE value in your toolchain compiler preprocessor. */ + +/* ########################### System Configuration ######################### */ +/** + * @brief This is the HAL system configuration section + */ +#define VDD_VALUE ((uint32_t)3300) /*!< Value of VDD in mv */ +#define TICK_INT_PRIORITY ((uint32_t)0x0F) /*!< tick interrupt priority */ +#define USE_RTOS 0 +#define USE_SD_TRANSCEIVER 1U /*!< use uSD Transceiver */ +#define USE_SPI_CRC 1U /*!< use CRC in SPI */ + +#define USE_HAL_ADC_REGISTER_CALLBACKS 0U /* ADC register callback disabled */ +#define USE_HAL_CEC_REGISTER_CALLBACKS 0U /* CEC register callback disabled */ +#define USE_HAL_COMP_REGISTER_CALLBACKS 0U /* COMP register callback disabled */ +#define USE_HAL_CRYP_REGISTER_CALLBACKS 0U /* CRYP register callback disabled */ +#define USE_HAL_DAC_REGISTER_CALLBACKS 0U /* DAC register callback disabled */ +#define USE_HAL_DCMI_REGISTER_CALLBACKS 0U /* DCMI register callback disabled */ +#define USE_HAL_DFSDM_REGISTER_CALLBACKS 0U /* DFSDM register callback disabled */ +#define USE_HAL_DMA2D_REGISTER_CALLBACKS 0U /* DMA2D register callback disabled */ +#define USE_HAL_DSI_REGISTER_CALLBACKS 0U /* DSI register callback disabled */ +#define USE_HAL_ETH_REGISTER_CALLBACKS 0U /* ETH register callback disabled */ +#define USE_HAL_FDCAN_REGISTER_CALLBACKS 0U /* FDCAN register callback disabled */ +#define USE_HAL_NAND_REGISTER_CALLBACKS 0U /* NAND register callback disabled */ +#define USE_HAL_NOR_REGISTER_CALLBACKS 0U /* NOR register callback disabled */ +#define USE_HAL_SDRAM_REGISTER_CALLBACKS 0U /* SDRAM register callback disabled */ +#define USE_HAL_SRAM_REGISTER_CALLBACKS 0U /* SRAM register callback disabled */ +#define USE_HAL_HASH_REGISTER_CALLBACKS 0U /* HASH register callback disabled */ +#define USE_HAL_HCD_REGISTER_CALLBACKS 0U /* HCD register callback disabled */ +#define USE_HAL_HRTIM_REGISTER_CALLBACKS 0U /* HRTIM register callback disabled */ +#define USE_HAL_I2C_REGISTER_CALLBACKS 0U /* I2C register callback disabled */ +#define USE_HAL_I2S_REGISTER_CALLBACKS 0U /* I2S register callback disabled */ +#define USE_HAL_JPEG_REGISTER_CALLBACKS 0U /* JPEG register callback disabled */ +#define USE_HAL_LPTIM_REGISTER_CALLBACKS 0U /* LPTIM register callback disabled */ +#define USE_HAL_LTDC_REGISTER_CALLBACKS 0U /* LTDC register callback disabled */ +#define USE_HAL_MDIOS_REGISTER_CALLBACKS 0U /* MDIO register callback disabled */ +#define USE_HAL_OPAMP_REGISTER_CALLBACKS 0U /* MDIO register callback disabled */ +#define USE_HAL_PCD_REGISTER_CALLBACKS 0U /* PCD register callback disabled */ +#define USE_HAL_QSPI_REGISTER_CALLBACKS 0U /* QSPI register callback disabled */ +#define USE_HAL_RNG_REGISTER_CALLBACKS 0U /* RNG register callback disabled */ +#define USE_HAL_RTC_REGISTER_CALLBACKS 0U /* RTC register callback disabled */ +#define USE_HAL_SAI_REGISTER_CALLBACKS 0U /* SAI register callback disabled */ +#define USE_HAL_SPDIFRX_REGISTER_CALLBACKS 0U /* SPDIFRX register callback disabled */ +#define USE_HAL_SMBUS_REGISTER_CALLBACKS 0U /* SMBUS register callback disabled */ +#define USE_HAL_SPI_REGISTER_CALLBACKS 0U /* SPI register callback disabled */ +#define USE_HAL_SWPMI_REGISTER_CALLBACKS 0U /* SWPMI register callback disabled */ +#define USE_HAL_TIM_REGISTER_CALLBACKS 0U /* TIM register callback disabled */ +#define USE_HAL_UART_REGISTER_CALLBACKS 0U /* UART register callback disabled */ +#define USE_HAL_USART_REGISTER_CALLBACKS 0U /* USART register callback disabled */ +#define USE_HAL_WWDG_REGISTER_CALLBACKS 0U /* WWDG register callback disabled */ + +/* ########################### Ethernet Configuration ######################### */ +#define ETH_TX_DESC_CNT 4 /* number of Ethernet Tx DMA descriptors */ +#define ETH_RX_DESC_CNT 4 /* number of Ethernet Rx DMA descriptors */ + +#define ETH_MAC_ADDR0 ((uint8_t)0x02) +#define ETH_MAC_ADDR1 ((uint8_t)0x00) +#define ETH_MAC_ADDR2 ((uint8_t)0x00) +#define ETH_MAC_ADDR3 ((uint8_t)0x00) +#define ETH_MAC_ADDR4 ((uint8_t)0x00) +#define ETH_MAC_ADDR5 ((uint8_t)0x00) + +/* ########################## Assert Selection ############################## */ +/** + * @brief Uncomment the line below to expanse the "assert_param" macro in the + * HAL drivers code + */ +/* #define USE_FULL_ASSERT 1 */ + + +/* Includes ------------------------------------------------------------------*/ +/** + * @brief Include module's header file + */ + +#ifdef HAL_RCC_MODULE_ENABLED + #include "stm32h7xx_hal_rcc.h" +#endif /* HAL_RCC_MODULE_ENABLED */ + +#ifdef HAL_GPIO_MODULE_ENABLED + #include "stm32h7xx_hal_gpio.h" +#endif /* HAL_GPIO_MODULE_ENABLED */ + +#ifdef HAL_DMA_MODULE_ENABLED + #include "stm32h7xx_hal_dma.h" +#endif /* HAL_DMA_MODULE_ENABLED */ + +#ifdef HAL_MDMA_MODULE_ENABLED + #include "stm32h7xx_hal_mdma.h" +#endif /* HAL_MDMA_MODULE_ENABLED */ + +#ifdef HAL_HASH_MODULE_ENABLED + #include "stm32h7xx_hal_hash.h" +#endif /* HAL_HASH_MODULE_ENABLED */ + +#ifdef HAL_DCMI_MODULE_ENABLED + #include "stm32h7xx_hal_dcmi.h" +#endif /* HAL_DCMI_MODULE_ENABLED */ + +#ifdef HAL_DMA2D_MODULE_ENABLED + #include "stm32h7xx_hal_dma2d.h" +#endif /* HAL_DMA2D_MODULE_ENABLED */ + +#ifdef HAL_DSI_MODULE_ENABLED + #include "stm32h7xx_hal_dsi.h" +#endif /* HAL_DSI_MODULE_ENABLED */ + +#ifdef HAL_DFSDM_MODULE_ENABLED + #include "stm32h7xx_hal_dfsdm.h" +#endif /* HAL_DFSDM_MODULE_ENABLED */ + +#ifdef HAL_ETH_MODULE_ENABLED + #include "stm32h7xx_hal_eth.h" +#endif /* HAL_ETH_MODULE_ENABLED */ + +#ifdef HAL_EXTI_MODULE_ENABLED + #include "stm32h7xx_hal_exti.h" +#endif /* HAL_EXTI_MODULE_ENABLED */ + +#ifdef HAL_CORTEX_MODULE_ENABLED + #include "stm32h7xx_hal_cortex.h" +#endif /* HAL_CORTEX_MODULE_ENABLED */ + +#ifdef HAL_ADC_MODULE_ENABLED + #include "stm32h7xx_hal_adc.h" +#endif /* HAL_ADC_MODULE_ENABLED */ + +#ifdef HAL_FDCAN_MODULE_ENABLED + #include "stm32h7xx_hal_fdcan.h" +#endif /* HAL_FDCAN_MODULE_ENABLED */ + +#ifdef HAL_CEC_MODULE_ENABLED + #include "stm32h7xx_hal_cec.h" +#endif /* HAL_CEC_MODULE_ENABLED */ + +#ifdef HAL_COMP_MODULE_ENABLED + #include "stm32h7xx_hal_comp.h" +#endif /* HAL_COMP_MODULE_ENABLED */ + +#ifdef HAL_CRC_MODULE_ENABLED + #include "stm32h7xx_hal_crc.h" +#endif /* HAL_CRC_MODULE_ENABLED */ + +#ifdef HAL_CRYP_MODULE_ENABLED + #include "stm32h7xx_hal_cryp.h" +#endif /* HAL_CRYP_MODULE_ENABLED */ + +#ifdef HAL_DAC_MODULE_ENABLED + #include "stm32h7xx_hal_dac.h" +#endif /* HAL_DAC_MODULE_ENABLED */ + +#ifdef HAL_FLASH_MODULE_ENABLED + #include "stm32h7xx_hal_flash.h" +#endif /* HAL_FLASH_MODULE_ENABLED */ + +#ifdef HAL_HRTIM_MODULE_ENABLED + #include "stm32h7xx_hal_hrtim.h" +#endif /* HAL_HRTIM_MODULE_ENABLED */ + +#ifdef HAL_HSEM_MODULE_ENABLED + #include "stm32h7xx_hal_hsem.h" +#endif /* HAL_HSEM_MODULE_ENABLED */ + +#ifdef HAL_SRAM_MODULE_ENABLED + #include "stm32h7xx_hal_sram.h" +#endif /* HAL_SRAM_MODULE_ENABLED */ + +#ifdef HAL_NOR_MODULE_ENABLED + #include "stm32h7xx_hal_nor.h" +#endif /* HAL_NOR_MODULE_ENABLED */ + +#ifdef HAL_NAND_MODULE_ENABLED + #include "stm32h7xx_hal_nand.h" +#endif /* HAL_NAND_MODULE_ENABLED */ + +#ifdef HAL_I2C_MODULE_ENABLED + #include "stm32h7xx_hal_i2c.h" +#endif /* HAL_I2C_MODULE_ENABLED */ + +#ifdef HAL_I2S_MODULE_ENABLED + #include "stm32h7xx_hal_i2s.h" +#endif /* HAL_I2S_MODULE_ENABLED */ + +#ifdef HAL_IWDG_MODULE_ENABLED + #include "stm32h7xx_hal_iwdg.h" +#endif /* HAL_IWDG_MODULE_ENABLED */ + +#ifdef HAL_JPEG_MODULE_ENABLED + #include "stm32h7xx_hal_jpeg.h" +#endif /* HAL_JPEG_MODULE_ENABLED */ + +#ifdef HAL_MDIOS_MODULE_ENABLED + #include "stm32h7xx_hal_mdios.h" +#endif /* HAL_MDIOS_MODULE_ENABLED */ + +#ifdef HAL_MMC_MODULE_ENABLED + #include "stm32h7xx_hal_mmc.h" +#endif /* HAL_MMC_MODULE_ENABLED */ + +#ifdef HAL_LPTIM_MODULE_ENABLED +#include "stm32h7xx_hal_lptim.h" +#endif /* HAL_LPTIM_MODULE_ENABLED */ + +#ifdef HAL_LTDC_MODULE_ENABLED +#include "stm32h7xx_hal_ltdc.h" +#endif /* HAL_LTDC_MODULE_ENABLED */ + +#ifdef HAL_OPAMP_MODULE_ENABLED +#include "stm32h7xx_hal_opamp.h" +#endif /* HAL_OPAMP_MODULE_ENABLED */ + +#ifdef HAL_PWR_MODULE_ENABLED + #include "stm32h7xx_hal_pwr.h" +#endif /* HAL_PWR_MODULE_ENABLED */ + +#ifdef HAL_QSPI_MODULE_ENABLED + #include "stm32h7xx_hal_qspi.h" +#endif /* HAL_QSPI_MODULE_ENABLED */ + +#ifdef HAL_RAMECC_MODULE_ENABLED + #include "stm32h7xx_hal_ramecc.h" +#endif /* HAL_HCD_MODULE_ENABLED */ + +#ifdef HAL_RNG_MODULE_ENABLED + #include "stm32h7xx_hal_rng.h" +#endif /* HAL_RNG_MODULE_ENABLED */ + +#ifdef HAL_RTC_MODULE_ENABLED + #include "stm32h7xx_hal_rtc.h" +#endif /* HAL_RTC_MODULE_ENABLED */ + +#ifdef HAL_SAI_MODULE_ENABLED + #include "stm32h7xx_hal_sai.h" +#endif /* HAL_SAI_MODULE_ENABLED */ + +#ifdef HAL_SD_MODULE_ENABLED + #include "stm32h7xx_hal_sd.h" +#endif /* HAL_SD_MODULE_ENABLED */ + +#ifdef HAL_SDRAM_MODULE_ENABLED + #include "stm32h7xx_hal_sdram.h" +#endif /* HAL_SDRAM_MODULE_ENABLED */ + +#ifdef HAL_SPI_MODULE_ENABLED + #include "stm32h7xx_hal_spi.h" +#endif /* HAL_SPI_MODULE_ENABLED */ + +#ifdef HAL_SPDIFRX_MODULE_ENABLED + #include "stm32h7xx_hal_spdifrx.h" +#endif /* HAL_SPDIFRX_MODULE_ENABLED */ + +#ifdef HAL_SWPMI_MODULE_ENABLED + #include "stm32h7xx_hal_swpmi.h" +#endif /* HAL_SWPMI_MODULE_ENABLED */ + +#ifdef HAL_TIM_MODULE_ENABLED + #include "stm32h7xx_hal_tim.h" +#endif /* HAL_TIM_MODULE_ENABLED */ + +#ifdef HAL_UART_MODULE_ENABLED + #include "stm32h7xx_hal_uart.h" +#endif /* HAL_UART_MODULE_ENABLED */ + +#ifdef HAL_USART_MODULE_ENABLED + #include "stm32h7xx_hal_usart.h" +#endif /* HAL_USART_MODULE_ENABLED */ + +#ifdef HAL_IRDA_MODULE_ENABLED + #include "stm32h7xx_hal_irda.h" +#endif /* HAL_IRDA_MODULE_ENABLED */ + +#ifdef HAL_SMARTCARD_MODULE_ENABLED + #include "stm32h7xx_hal_smartcard.h" +#endif /* HAL_SMARTCARD_MODULE_ENABLED */ + +#ifdef HAL_SMBUS_MODULE_ENABLED + #include "stm32h7xx_hal_smbus.h" +#endif /* HAL_SMBUS_MODULE_ENABLED */ + +#ifdef HAL_WWDG_MODULE_ENABLED + #include "stm32h7xx_hal_wwdg.h" +#endif /* HAL_WWDG_MODULE_ENABLED */ + +#ifdef HAL_PCD_MODULE_ENABLED + #include "stm32h7xx_hal_pcd.h" +#endif /* HAL_PCD_MODULE_ENABLED */ + +#ifdef HAL_HCD_MODULE_ENABLED + #include "stm32h7xx_hal_hcd.h" +#endif /* HAL_HCD_MODULE_ENABLED */ + +/* Exported macro ------------------------------------------------------------*/ +#ifdef USE_FULL_ASSERT +/** + * @brief The assert_param macro is used for function's parameters check. + * @param expr: If expr is false, it calls assert_failed function + * which reports the name of the source file and the source + * line number of the call that failed. + * If expr is true, it returns no value. + * @retval None + */ + #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__)) +/* Exported functions ------------------------------------------------------- */ + void assert_failed(uint8_t *file, uint32_t line); +#else + #define assert_param(expr) ((void)0U) +#endif /* USE_FULL_ASSERT */ + +#ifdef __cplusplus +} +#endif + +#endif /* __STM32H7xx_HAL_CONF_H */ + + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ |