diff options
Diffstat (limited to 'watch-library/hardware/hal/include/hal_i2c_m_sync.h')
-rw-r--r-- | watch-library/hardware/hal/include/hal_i2c_m_sync.h | 244 |
1 files changed, 244 insertions, 0 deletions
diff --git a/watch-library/hardware/hal/include/hal_i2c_m_sync.h b/watch-library/hardware/hal/include/hal_i2c_m_sync.h new file mode 100644 index 00000000..f7772483 --- /dev/null +++ b/watch-library/hardware/hal/include/hal_i2c_m_sync.h @@ -0,0 +1,244 @@ +/** + * \file + * + * \brief Sync I2C Hardware Abstraction Layer(HAL) declaration. + * + * Copyright (c) 2014-2018 Microchip Technology Inc. and its subsidiaries. + * + * \asf_license_start + * + * \page License + * + * Subject to your compliance with these terms, you may use Microchip + * software and any derivatives exclusively with Microchip products. + * It is your responsibility to comply with third party license terms applicable + * to your use of third party software (including open source software) that + * may accompany Microchip software. + * + * THIS SOFTWARE IS SUPPLIED BY MICROCHIP "AS IS". NO WARRANTIES, + * WHETHER EXPRESS, IMPLIED OR STATUTORY, APPLY TO THIS SOFTWARE, + * INCLUDING ANY IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY, + * AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT WILL MICROCHIP BE + * LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE, INCIDENTAL OR CONSEQUENTIAL + * LOSS, DAMAGE, COST OR EXPENSE OF ANY KIND WHATSOEVER RELATED TO THE + * SOFTWARE, HOWEVER CAUSED, EVEN IF MICROCHIP HAS BEEN ADVISED OF THE + * POSSIBILITY OR THE DAMAGES ARE FORESEEABLE. TO THE FULLEST EXTENT + * ALLOWED BY LAW, MICROCHIP'S TOTAL LIABILITY ON ALL CLAIMS IN ANY WAY + * RELATED TO THIS SOFTWARE WILL NOT EXCEED THE AMOUNT OF FEES, IF ANY, + * THAT YOU HAVE PAID DIRECTLY TO MICROCHIP FOR THIS SOFTWARE. + * + * \asf_license_stop + * + */ + +#ifndef _HAL_I2C_M_SYNC_H_INCLUDED +#define _HAL_I2C_M_SYNC_H_INCLUDED + +#include <hpl_i2c_m_sync.h> +#include <hal_io.h> + +#ifdef __cplusplus +extern "C" { +#endif + +/** + * \addtogroup doc_driver_hal_i2c_controller_sync + * + * @{ + */ + +#define I2C_M_MAX_RETRY 1 + +/** + * \brief I2C descriptor structure, embed i2c_device & i2c_interface + */ +struct i2c_m_sync_desc { + struct _i2c_m_sync_device device; + struct io_descriptor io; + uint16_t periph_addr; +}; + +/** + * \brief Initialize synchronous I2C interface + * + * This function initializes the given I/O descriptor to be used as a + * synchronous I2C interface descriptor. + * It checks if the given hardware is not initialized and if the given hardware + * is permitted to be initialized. + * + * \param[in] i2c An I2C descriptor, which is used to communicate through I2C + * \param[in] hw The pointer to hardware instance + * + * \return Initialization status. + * \retval -1 The passed parameters were invalid or the interface is already initialized + * \retval 0 The initialization is completed successfully + */ +int32_t i2c_m_sync_init(struct i2c_m_sync_desc *i2c, void *hw); + +/** + * \brief Deinitialize I2C interface + * + * This function deinitializes the given I/O descriptor. + * It checks if the given hardware is initialized and if the given hardware is permitted to be deinitialized. + * + * \param[in] i2c An I2C descriptor, which is used to communicate through I2C + * + * \return Uninitialization status. + * \retval -1 The passed parameters were invalid or the interface is already deinitialized + * \retval 0 The de-initialization is completed successfully + */ +int32_t i2c_m_sync_deinit(struct i2c_m_sync_desc *i2c); + +/** + * \brief Set the peripheral device address + * + * This function sets the next transfer target peripheral I2C device address. + * It takes no effect to any already started access. + * + * \param[in] i2c An I2C descriptor, which is used to communicate through I2C + * \param[in] addr The peripheral address to access + * \param[in] addr_len The peripheral address length, can be I2C_M_TEN or I2C_M_SEVEN + * + * \return Masked peripheral address. The mask is a maximum 10-bit address, and 10th + * bit is set if a 10-bit address is used + */ +int32_t i2c_m_sync_set_periphaddr(struct i2c_m_sync_desc *i2c, int16_t addr, int32_t addr_len); + +/** + * \brief Set baudrate + * + * This function sets the I2C device to the specified baudrate. + * It only takes effect when the hardware is disabled. + * + * \param[in] i2c An I2C descriptor, which is used to communicate through I2C + * \param[in] clkrate Unused parameter. Should always be 0 + * \param[in] baudrate The baudrate value set to controller + * + * \return Whether successfully set the baudrate + * \retval -1 The passed parameters were invalid or the device is already enabled + * \retval 0 The baudrate set is completed successfully + */ +int32_t i2c_m_sync_set_baudrate(struct i2c_m_sync_desc *i2c, uint32_t clkrate, uint32_t baudrate); + +/** + * \brief Sync version of enable hardware + * + * This function enables the I2C device, and then waits for this enabling operation to be done + * + * \param[in] i2c An I2C descriptor, which is used to communicate through I2C + * + * \return Whether successfully enable the device + * \retval -1 The passed parameters were invalid or the device enable failed + * \retval 0 The hardware enabling is completed successfully + */ +int32_t i2c_m_sync_enable(struct i2c_m_sync_desc *i2c); + +/** + * \brief Sync version of disable hardware + * + * This function disables the I2C device and then waits for this disabling operation to be done + * + * \param[in] i2c An I2C descriptor, which is used to communicate through I2C + * + * \return Whether successfully disable the device + * \retval -1 The passed parameters were invalid or the device disable failed + * \retval 0 The hardware disabling is completed successfully + */ +int32_t i2c_m_sync_disable(struct i2c_m_sync_desc *i2c); + +/** + * \brief Sync version of write command to I2C peripheral + * + * This function will write the value to a specified register in the I2C peripheral device and + * then wait for this operation to be done. + * + * The sequence of this routine is + * sta->address(write)->ack->reg address->ack->resta->address(write)->ack->reg value->nack->stt + * + * \param[in] i2c An I2C descriptor, which is used to communicate through I2C + * \param[in] reg The internal address/register of the I2C peripheral device + * \param[in] buffer The buffer holding data to write to the I2C peripheral device + * \param[in] length The length (in bytes) to write to the I2C peripheral device + * + * \return Whether successfully write to the device + * \retval <0 The passed parameters were invalid or write fail + * \retval 0 Writing to register is completed successfully + */ +int32_t i2c_m_sync_cmd_write(struct i2c_m_sync_desc *i2c, uint8_t reg, uint8_t *buffer, uint8_t length); + +/** + * \brief Sync version of read register value from I2C peripheral + * + * This function will read a byte value from a specified register in the I2C peripheral device and + * then wait for this operation to be done. + * + * The sequence of this routine is + * sta->address(write)->ack->reg address->ack->resta->address(read)->ack->reg value->nack->stt + * + * \param[in] i2c An I2C descriptor, which is used to communicate through I2C + * \param[in] reg The internal address/register of the I2C peripheral device + * \param[in] buffer The buffer to hold the read data from the I2C peripheral device + * \param[in] length The length (in bytes) to read from the I2C peripheral device + * + * \return Whether successfully read from the device + * \retval <0 The passed parameters were invalid or read fail + * \retval 0 Reading from register is completed successfully + */ +int32_t i2c_m_sync_cmd_read(struct i2c_m_sync_desc *i2c, uint8_t reg, uint8_t *buffer, uint8_t length); + +/** + * \brief Sync version of transfer message to/from the I2C peripheral + * + * This function will transfer a message between the I2C peripheral and the controller. + * This function will wait for the operation to be done. + * + * \param[in] i2c An I2C descriptor, which is used to communicate through I2C + * \param[in] msg An i2c_m_msg struct + * + * \return The status of the operation + * \retval 0 Operation completed successfully + * \retval <0 Operation failed + */ +int32_t i2c_m_sync_transfer(struct i2c_m_sync_desc *const i2c, struct _i2c_m_msg *msg); + +/** + * \brief Sync version of send stop condition on the i2c bus + * + * This function will create a stop condition on the i2c bus to release the bus + * + * \param[in] i2c An I2C descriptor, which is used to communicate through I2C + * + * \return The status of the operation + * \retval 0 Operation completed successfully + * \retval <0 Operation failed + */ +int32_t i2c_m_sync_send_stop(struct i2c_m_sync_desc *const i2c); + +/** + * \brief Return I/O descriptor for this I2C instance + * + * This function will return a I/O instance for this I2C driver instance + * + * \param[in] i2c_m_sync_desc An I2C descriptor, which is used to communicate through I2C + * \param[in] io_descriptor A pointer to an I/O descriptor pointer type + * + * \return Error code + * \retval 0 No error detected + * \retval <0 Error code + */ +int32_t i2c_m_sync_get_io_descriptor(struct i2c_m_sync_desc *const i2c, struct io_descriptor **io); + +/** + * \brief Retrieve the current driver version + * + * \return Current driver version. + */ +uint32_t i2c_m_sync_get_version(void); + +/**@}*/ + +#ifdef __cplusplus +} +#endif + +#endif |