1 files changed, 239 insertions, 0 deletions
diff --git a/watch-library/shared/config/hpl_slcd_config.h b/watch-library/shared/config/hpl_slcd_config.h
new file mode 100644
index 00000000..d78e3391
--- /dev/null
+++ b/watch-library/shared/config/hpl_slcd_config.h
@@ -0,0 +1,239 @@
+/* Auto-generated config file hpl_slcd_config.h */
+#ifndef HPL_SLCD_CONFIG_H
+#define HPL_SLCD_CONFIG_H
+
+// <<< Use Configuration Wizard in Context Menu >>>
+
+#include <hpl_slcd_cm.h>
+#include <peripheral_clk_config.h>
+#include "pins.h"
+
+// <h> Standard configuration
+
+// <o> Number of COM Lines
+// <i> Number of COM Lines
+// <0=>1
+// <1=>2
+// <2=>3
+// <3=>4
+// <4=>6
+// <5=>8
+// <id> slcd_arch_com_num
+#ifndef CONF_SLCD_COM_NUM
+#define CONF_SLCD_COM_NUM 2
+#endif
+
+// <o> Number of Segment Lines <1-44>
+// <i> Number of Segment Lines
+// <id> slcd_arch_seg_num
+#ifndef CONF_SLCD_SEG_NUM
+#define CONF_SLCD_SEG_NUM 24
+#endif
+
+#if CONF_SLCD_COM_NUM == SLCD_CTRLA_DUTY_SIXTH_Val && CONF_SLCD_SEG_NUM > 42
+#warning Segment number should less than or equals to 42
+#endif
+#if CONF_SLCD_COM_NUM == SLCD_CTRLA_DUTY_EIGHT_Val && CONF_SLCD_SEG_NUM > 40
+#warning Segment number should less than or equals to 40
+#endif
+
+// <o> Bias
+// <i> Bias Settting
+// <0=>STATIC
+// <1=>HALF
+// <2=>THIRD
+// <3=>FOURTH
+// <id> slcd_arch_bias
+#ifndef CONF_SLCD_BIAS
+#define CONF_SLCD_BIAS 2
+#endif
+
+#if CONF_SLCD_COM_NUM == 0 && CONF_SLCD_BIAS != 0
+#warning Recommended Bias for 1 common terminal is STATIC
+#elif CONF_SLCD_COM_NUM == 1 && CONF_SLCD_BIAS != 1
+#warning Recommended Bias for 2 Common Terminals is HALF
+#elif CONF_SLCD_COM_NUM <= 4 && CONF_SLCD_BIAS != 2
+#warning Recommended Bias for 3/4/6 Common Terminals is THIRD
+#elif CONF_SLCD_COM_NUM == 5 && CONF_SLCD_BIAS != 3
+#warning Recommended Bias for 8 Common Terminals is FOURTH
+#endif
+
+// <q> Bias Buffer Enable
+// <i> Enable Bias Buffer
+// <id> slcd_arch_bben
+#ifndef CONF_SLCD_BBEN
+#define CONF_SLCD_BBEN 1
+#endif
+
+// <o> Bias Buffer Enable Duration <1-16>
+// <i> Configure the enable duration of the bias buffer, unit is cycle of SLCD OSC clock source
+// <id> slcd_arch_bbd
+#ifndef CONF_SLCD_BBD
+#define CONF_SLCD_BBD 2
+#endif
+
+// <o> Clock Prescaler
+// <i> Setting for LCD frame frequency
+// <0=>16
+// <1=>32
+// <2=>64
+// <3=>128
+// <id> slcd_arch_presc
+#ifndef CONF_SLCD_PRESC
+#define CONF_SLCD_PRESC 1
+#endif
+
+// <o> Clock Divider
+// <i> Setting for LCD frame frequency
+// <0=>1
+// <1=>2
+// <2=>3
+// <3=>4
+// <4=>5
+// <5=>6
+// <6=>7
+// <7=>8
+// <id> slcd_arch_ckdiv
+#ifndef CONF_SLCD_CKDIV
+#define CONF_SLCD_CKDIV 5
+#endif
+
+/* TODO add frame frequency check */
+
+// <o> Reference Refresh Frequency
+// <i> Setting for Reference Refresh Frequency
+// <0=>2kHz
+// <1=>1kHz
+// <2=>500Hz
+// <3=>250Hz
+// <4=>125Hz
+// <5=>62.5Hz
+// <id> slcd_arch_rrf
+#ifndef CONF_SLCD_RRF
+#define CONF_SLCD_RRF 0
+#endif
+
+// <o> Power Refresh Frequency
+// <i> Setting for Charge pump Refresh Frequency
+// <0=>2kHz
+// <1=>1kHz
+// <2=>500Hz
+// <3=>250Hz
+// <id> slcd_arch_prf
+#ifndef CONF_SLCD_PRF
+#define CONF_SLCD_PRF 3
+#endif
+
+// <q> External VLCD
+// <i> Setting for how VLCD is generated
+// <id> slcd_arch_xvlcd
+#ifndef CONF_SLCD_XVLCD
+#define CONF_SLCD_XVLCD 0
+#endif
+
+// <o> Waveform Mode
+// <i> Setting for Waveform Mode
+// <0=>Low Power Waveform(frame-inversion)
+// <1=>Standard Waveform Mode(bit-inversion)
+// <id> slcd_arch_wmod
+#ifndef CONF_SLCD_WMOD
+#define CONF_SLCD_WMOD 0
+#endif
+
+// <o> Contrast Adjustment
+// <i> The contrast of the LCD is determined by the value of VLCD voltage.
+// <i> The higher the VLCD voltage, the higher is the contrast.
+// <i> The software contrast adjustment is only possible in internal supply mode.
+// <0=>2.5056V
+// <1=>2.5731V
+// <2=>2.6379V
+// <3=>2.7054V
+// <4=>2.7729V
+// <5=>2.8404V
+// <6=>2.9052V
+// <7=>2.9727V
+// <8=>3.0402V
+// <9=>3.1077V
+// <10=>3.1725V
+// <11=>3.24V
+// <12=>3.3075V
+// <13=>3.375V
+// <14=>3.4398V
+// <15=>3.5073V
+// <id> slcd_arch_contrast_adjust
+#ifndef CONF_SLCD_CONTRAST_ADJUST
+#define CONF_SLCD_CONTRAST_ADJUST 14
+#endif
+
+// </h>
+
+// <e> Advanced configuration
+// <id> slcd_arch_advanced_settings
+#ifndef CONF_SLCD_ADVANCED_SETTINGS
+#define CONF_SLCD_ADVANCED_SETTINGS 1
+#endif
+
+// <q> Run in standby
+// <i> Indicates whether the SLCD will continue running in standby sleep mode or not
+// <id> slcd_arch_runstdby
+#ifndef CONF_SLCD_RUNSTDBY
+#define CONF_SLCD_RUNSTDBY 1
+#endif
+
+// </e>
+
+#if SLCD_FRAME_FREQUENCY < 30 || SLCD_FRAME_FREQUENCY > 100
+#warning The optimal frame frequency should be in range from 30Hz up to 100Hz to avoid flickering and ghosting effect.
+#endif
+
+#define SLCD_FC_MAX_MS (((0x1F + 1) * 8) * (1000 / SLCD_FRAME_FREQUENCY))
+#define SLCD_FC_MIN_MS (1000 / SLCD_FRAME_FREQUENCY)
+#define SLCD_FC_BYPASS_MAX_MS ((0x1F + 1) * (1000 / SLCD_FRAME_FREQUENCY))
+
+// <e> Character Mapping Setting
+// <id> slcd_arch_cm_setting
+#ifndef CONF_SLCD_CM_ENABLE
+#define CONF_SLCD_CM_ENABLE 0
+#endif
+
+/**
+ * character lookup table
+ */
+#ifndef CONF_SLCD_LPENL
+#define CONF_SLCD_LPENL (\
+		(uint32_t)1 <<  0 | \
+		(uint32_t)1 <<  1 | \
+		(uint32_t)1 <<  2 | \
+		(uint32_t)1 <<  3 | \
+		(uint32_t)1 <<  4 | \
+		(uint32_t)1 <<  5 | \
+		(uint32_t)1 <<  6 | \
+		(uint32_t)1 <<  7 | \
+		(uint32_t)1 << 11 | \
+		(uint32_t)1 << 12 | \
+		(uint32_t)1 << 13 | \
+		(uint32_t)1 << 14 | \
+		(uint32_t)1 << 21 | \
+		(uint32_t)1 << 22 | \
+		(uint32_t)1 << 23 | \
+		(uint32_t)1 << 24 | \
+		(uint32_t)1 << 25 | \
+		(uint32_t)1 << 28 | \
+		(uint32_t)1 << 29 | \
+		(uint32_t)1 << 30 | \
+		(uint32_t)1 << 31 | 0)
+#endif // CONF_SLCD_LPENL
+
+#ifndef CONF_SLCD_LPENH
+#define CONF_SLCD_LPENH (\
+		(uint32_t)1 << (32 - 32) | \
+		(uint32_t)1 << (33 - 32) | \
+		(uint32_t)1 << (34 - 32) | \
+		(uint32_t)1 << (35 - 32) | \
+		(uint32_t)1 << (42 - 32) | \
+		(uint32_t)1 << (43 - 32) | 0)
+#endif // CONF_SLCD_LPENH
+
+// <<< end of configuration section >>>
+
+#endif // HPL_SLCD_CONFIG_H