diff options
Diffstat (limited to 'watch-library/shared/config')
| -rw-r--r-- | watch-library/shared/config/RTE_Components.h | 54 | ||||
| -rw-r--r-- | watch-library/shared/config/hpl_dmac_config.h | 3122 | ||||
| -rw-r--r-- | watch-library/shared/config/hpl_eic_config.h | 736 | ||||
| -rw-r--r-- | watch-library/shared/config/hpl_gclk_config.h | 388 | ||||
| -rw-r--r-- | watch-library/shared/config/hpl_mclk_config.h | 85 | ||||
| -rwxr-xr-x | watch-library/shared/config/hpl_nvmctrl_config.h | 38 | ||||
| -rw-r--r-- | watch-library/shared/config/hpl_osc32kctrl_config.h | 177 | ||||
| -rw-r--r-- | watch-library/shared/config/hpl_oscctrl_config.h | 483 | ||||
| -rw-r--r-- | watch-library/shared/config/hpl_port_config.h | 284 | ||||
| -rw-r--r-- | watch-library/shared/config/hpl_rtc_config.h | 318 | ||||
| -rw-r--r-- | watch-library/shared/config/hpl_sercom_config.h | 303 | ||||
| -rw-r--r-- | watch-library/shared/config/hpl_slcd_config.h | 239 | ||||
| -rw-r--r-- | watch-library/shared/config/hpl_systick_config.h | 18 | ||||
| -rwxr-xr-x | watch-library/shared/config/hpl_trng_config.h | 27 | ||||
| -rwxr-xr-x | watch-library/shared/config/nv_storage_config.h | 51 | ||||
| -rw-r--r-- | watch-library/shared/config/peripheral_clk_config.h | 266 |
16 files changed, 6589 insertions, 0 deletions
diff --git a/watch-library/shared/config/RTE_Components.h b/watch-library/shared/config/RTE_Components.h new file mode 100644 index 00000000..3ba6b1ba --- /dev/null +++ b/watch-library/shared/config/RTE_Components.h @@ -0,0 +1,54 @@ + /**
+ * \file
+ *
+ * \brief Autogenerated API include file for the Atmel Configuration Management Engine (ACME)
+ *
+ * Copyright (c) 2012 Atmel Corporation. All rights reserved.
+ *
+ * \acme_license_start
+ *
+ * \page License
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright notice,
+ * this list of conditions and the following disclaimer.
+ *
+ * 2. Redistributions in binary form must reproduce the above copyright notice,
+ * this list of conditions and the following disclaimer in the documentation
+ * and/or other materials provided with the distribution.
+ *
+ * 3. The name of Atmel may not be used to endorse or promote products derived
+ * from this software without specific prior written permission.
+ *
+ * 4. This software may only be redistributed and used in connection with an
+ * Atmel microcontroller product.
+ *
+ * THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR IMPLIED
+ * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+ * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
+ * EXPRESSLY AND SPECIFICALLY DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR
+ * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
+ * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
+ * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
+ * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
+ * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ *
+ * \acme_license_stop
+ *
+ * Project: My Project
+ * Target: ATSAML22J18A
+ *
+ **/
+
+
+#ifndef RTE_COMPONENTS_H
+#define RTE_COMPONENTS_H
+
+
+#define ATMEL_START
+
+#endif /* RTE_COMPONENTS_H */
diff --git a/watch-library/shared/config/hpl_dmac_config.h b/watch-library/shared/config/hpl_dmac_config.h new file mode 100644 index 00000000..36adb88b --- /dev/null +++ b/watch-library/shared/config/hpl_dmac_config.h @@ -0,0 +1,3122 @@ +/* Auto-generated config file hpl_dmac_config.h */ +#ifndef HPL_DMAC_CONFIG_H +#define HPL_DMAC_CONFIG_H + +// <<< Use Configuration Wizard in Context Menu >>> + +// <e> DMAC enable +// <i> Indicates whether dmac is enabled or not +// <id> dmac_enable +#ifndef CONF_DMAC_ENABLE +#define CONF_DMAC_ENABLE 0 +#endif + +// <q> Priority Level 0 +// <i> Indicates whether Priority Level 0 is enabled or not +// <id> dmac_lvlen0 +#ifndef CONF_DMAC_LVLEN0 +#define CONF_DMAC_LVLEN0 0 +#endif + +// <o> Level 0 Round-Robin Arbitration +// <0=> Static arbitration scheme for channel with priority 0 +// <1=> Round-robin arbitration scheme for channel with priority 0 +// <i> Defines Level 0 Arbitration for DMA channels +// <id> dmac_rrlvlen0 +#ifndef CONF_DMAC_RRLVLEN0 +#define CONF_DMAC_RRLVLEN0 0 +#endif + +// <o> Level 0 Channel Priority Number <0x00-0xFF> +// <id> dmac_lvlpri0 +#ifndef CONF_DMAC_LVLPRI0 +#define CONF_DMAC_LVLPRI0 0 +#endif + +// <q> Priority Level 1 +// <i> Indicates whether Priority Level 1 is enabled or not +// <id> dmac_lvlen1 +#ifndef CONF_DMAC_LVLEN1 +#define CONF_DMAC_LVLEN1 0 +#endif + +// <o> Level 1 Round-Robin Arbitration +// <0=> Static arbitration scheme for channel with priority 1 +// <1=> Round-robin arbitration scheme for channel with priority 1 +// <i> Defines Level 1 Arbitration for DMA channels +// <id> dmac_rrlvlen1 +#ifndef CONF_DMAC_RRLVLEN1 +#define CONF_DMAC_RRLVLEN1 0 +#endif + +// <o> Level 1 Channel Priority Number <0x00-0xFF> +// <id> dmac_lvlpri1 +#ifndef CONF_DMAC_LVLPRI1 +#define CONF_DMAC_LVLPRI1 0 +#endif + +// <q> Priority Level 2 +// <i> Indicates whether Priority Level 2 is enabled or not +// <id> dmac_lvlen2 +#ifndef CONF_DMAC_LVLEN2 +#define CONF_DMAC_LVLEN2 0 +#endif + +// <o> Level 2 Round-Robin Arbitration +// <0=> Static arbitration scheme for channel with priority 2 +// <1=> Round-robin arbitration scheme for channel with priority 2 +// <i> Defines Level 2 Arbitration for DMA channels +// <id> dmac_rrlvlen2 +#ifndef CONF_DMAC_RRLVLEN2 +#define CONF_DMAC_RRLVLEN2 0 +#endif + +// <o> Level 2 Channel Priority Number <0x00-0xFF> +// <id> dmac_lvlpri2 +#ifndef CONF_DMAC_LVLPRI2 +#define CONF_DMAC_LVLPRI2 0 +#endif + +// <q> Priority Level 3 +// <i> Indicates whether Priority Level 3 is enabled or not +// <id> dmac_lvlen3 +#ifndef CONF_DMAC_LVLEN3 +#define CONF_DMAC_LVLEN3 0 +#endif + +// <o> Level 3 Round-Robin Arbitration +// <0=> Static arbitration scheme for channel with priority 3 +// <1=> Round-robin arbitration scheme for channel with priority 3 +// <i> Defines Level 3 Arbitration for DMA channels +// <id> dmac_rrlvlen3 +#ifndef CONF_DMAC_RRLVLEN3 +#define CONF_DMAC_RRLVLEN3 0 +#endif + +// <o> Level 3 Channel Priority Number <0x00-0xFF> +// <id> dmac_lvlpri3 +#ifndef CONF_DMAC_LVLPRI3 +#define CONF_DMAC_LVLPRI3 0 +#endif + +// <o> Data Transfer Quality of Service +// <0=> Background (no sensitive operation) +// <1=> Sensitive bandwidth +// <2=> Sensitive latency +// <3=> Critical latency +// <i> Defines the memory priority access during the data transfer operation +// <id> dmac_dqos +#ifndef CONF_DMAC_DQOS +#define CONF_DMAC_DQOS 0 +#endif + +// <o> Fetch Quality of Service +// <0=> Background (no sensitive operation) +// <1=> Sensitive bandwidth +// <2=> Sensitive latency +// <3=> Critical latency +// <i> Defines the memory priority access during the fetch operation +// <id> dmac_fqos +#ifndef CONF_DMAC_FQOS +#define CONF_DMAC_FQOS 0 +#endif + +// <o> Write-Back Quality of Service +// <0=> Background (no sensitive operation) +// <1=> Sensitive bandwidth +// <2=> Sensitive latency +// <3=> Critical latency +// <i> Defines the memory priority access during the write-back operation +// <id> dmac_wrbqos +#ifndef CONF_DMAC_WRBQOS +#define CONF_DMAC_WRBQOS 0 +#endif + +// <q> Debug Run +// <i> Indicates whether Debug Run is enabled or not +// <id> dmac_dbgrun +#ifndef CONF_DMAC_DBGRUN +#define CONF_DMAC_DBGRUN 0 +#endif + +// <e> Channel 0 settings +// <id> dmac_channel_0_settings +#ifndef CONF_DMAC_CHANNEL_0_SETTINGS +#define CONF_DMAC_CHANNEL_0_SETTINGS 0 +#endif + +// <q> Channel Enable +// <i> Indicates whether channel 0 is enabled or not +// <id> dmac_enable_0 +#ifndef CONF_DMAC_ENABLE_0 +#define CONF_DMAC_ENABLE_0 0 +#endif + +// <q> Channel Run in Standby +// <i> Indicates whether channel 0 is running in standby mode or not +// <id> dmac_runstdby_0 +#ifndef CONF_DMAC_RUNSTDBY_0 +#define CONF_DMAC_RUNSTDBY_0 0 +#endif + +// <o> Trigger action +// <0=> One trigger required for each block transfer +// <2=> One trigger required for each beat transfer +// <3=> One trigger required for each transaction +// <i> Defines the trigger action used for a transfer +// <id> dmac_trigact_0 +#ifndef CONF_DMAC_TRIGACT_0 +#define CONF_DMAC_TRIGACT_0 0 +#endif + +// <o> Trigger source +// <0x00=> Only software/event triggers +// <0x01=> RTC Timestamp +// <0x02=> SERCOM0 RX Trigger +// <0x03=> SERCOM0 TX Trigger +// <0x04=> SERCOM1 RX Trigger +// <0x05=> SERCOM1 TX Trigger +// <0x06=> SERCOM2 RX Trigger +// <0x07=> SERCOM2 TX Trigger +// <0x08=> SERCOM3 RX Trigger +// <0x09=> SERCOM3 TX Trigger +// <0x0A=> SERCOM4 RX Trigger +// <0x0B=> SERCOM4 TX Trigger +// <0x0C=> SERCOM5 RX Trigger +// <0x0D=> SERCOM5 TX Trigger +// <0x0E=> TCC0 Overflow Trigger +// <0x0F=> TCC0 Match/Compare 0 Trigger +// <0x10=> TCC0 Match/Compare 1 Trigger +// <0x11=> TCC0 Match/Compare 2 Trigger +// <0x12=> TCC0 Match/Compare 3 Trigger +// <0x13=> TC0 Overflow Trigger +// <0x14=> TC0 Match/Compare 0 Trigger +// <0x15=> TC0 Match/Compare 1 Trigger +// <0x16=> TC1 Overflow Trigger +// <0x17=> TC1 Match/Compare 0 Trigger +// <0x18=> TC1 Match/Compare 1 Trigger +// <0x19=> TC2 Overflow Trigger +// <0x1A=> TC2 Match/Compare 0 Trigger +// <0x1B=> TC2 Match/Compare 1 Trigger +// <0x1C=> TC3 Overflow Trigger +// <0x1D=> TC3 Match/Compare 0 Trigger +// <0x1E=> TC3 Match/Compare 1 Trigger +// <0x1F=> ADC Result Ready Trigger +// <0x20=> SLCD Display Memory Update Trigger +// <0x21=> SLCD Automated Character Mapping Data Ready Trigger +// <0x22=> SLCD Automated Bit Mapping Data Ready Trigger +// <0x23=> AES Write Trigger +// <0x24=> AES Read Trigger +// <0x25=> PTC End of Conversion Trigger +// <0x26=> PTC Sequence Trigger +// <0x27=> PTC Window Comparator Trigger +// <i> Defines the peripheral trigger which is source of the transfer +// <id> dmac_trifsrc_0 +#ifndef CONF_DMAC_TRIGSRC_0 +#define CONF_DMAC_TRIGSRC_0 0 +#endif + +// <o> Channel Arbitration Level +// <0=> Channel priority 0 +// <1=> Channel priority 1 +// <2=> Channel priority 2 +// <3=> Channel priority 3 +// <i> Defines the arbitration level for this channel +// <id> dmac_lvl_0 +#ifndef CONF_DMAC_LVL_0 +#define CONF_DMAC_LVL_0 0 +#endif + +// <q> Channel Event Output +// <i> Indicates whether channel event generation is enabled or not +// <id> dmac_evoe_0 +#ifndef CONF_DMAC_EVOE_0 +#define CONF_DMAC_EVOE_0 0 +#endif + +// <q> Channel Event Input +// <i> Indicates whether channel event reception is enabled or not +// <id> dmac_evie_0 +#ifndef CONF_DMAC_EVIE_0 +#define CONF_DMAC_EVIE_0 0 +#endif + +// <o> Event Input Action +// <0=> No action +// <1=> Normal transfer and conditional transfer on strobe trigger +// <2=> Conditional transfer trigger +// <3=> Conditional block transfer +// <4=> Channel suspend operation +// <5=> Channel resume operation +// <6=> Skip next block suspend action +// <i> Defines the event input action +// <id> dmac_evact_0 +#ifndef CONF_DMAC_EVACT_0 +#define CONF_DMAC_EVACT_0 0 +#endif + +// <o> Address Increment Step Size +// <0=> Next ADDR = ADDR + (BEATSIZE + 1) * 1 +// <1=> Next ADDR = ADDR + (BEATSIZE + 1) * 2 +// <2=> Next ADDR = ADDR + (BEATSIZE + 1) * 4 +// <3=> Next ADDR = ADDR + (BEATSIZE + 1) * 8 +// <4=> Next ADDR = ADDR + (BEATSIZE + 1) * 16 +// <5=> Next ADDR = ADDR + (BEATSIZE + 1) * 32 +// <6=> Next ADDR = ADDR + (BEATSIZE + 1) * 64 +// <7=> Next ADDR = ADDR + (BEATSIZE + 1) * 128 +// <i> Defines the address increment step size, applies to source or destination address +// <id> dmac_stepsize_0 +#ifndef CONF_DMAC_STEPSIZE_0 +#define CONF_DMAC_STEPSIZE_0 0 +#endif + +// <o> Step Selection +// <0=> Step size settings apply to the destination address +// <1=> Step size settings apply to the source address +// <i> Defines whether source or destination addresses are using the step size settings +// <id> dmac_stepsel_0 +#ifndef CONF_DMAC_STEPSEL_0 +#define CONF_DMAC_STEPSEL_0 0 +#endif + +// <q> Source Address Increment +// <i> Indicates whether the source address incrementation is enabled or not +// <id> dmac_srcinc_0 +#ifndef CONF_DMAC_SRCINC_0 +#define CONF_DMAC_SRCINC_0 0 +#endif + +// <q> Destination Address Increment +// <i> Indicates whether the destination address incrementation is enabled or not +// <id> dmac_dstinc_0 +#ifndef CONF_DMAC_DSTINC_0 +#define CONF_DMAC_DSTINC_0 0 +#endif + +// <o> Beat Size +// <0=> 8-bit bus transfer +// <1=> 16-bit bus transfer +// <2=> 32-bit bus transfer +// <i> Defines the size of one beat +// <id> dmac_beatsize_0 +#ifndef CONF_DMAC_BEATSIZE_0 +#define CONF_DMAC_BEATSIZE_0 0 +#endif + +// <o> Block Action +// <0=> Channel will be disabled if it is the last block transfer in the transaction +// <1=> Channel will be disabled if it is the last block transfer in the transaction and block interrupt +// <2=> Channel suspend operation is complete +// <3=> Both channel suspend operation and block interrupt +// <i> Defines the the DMAC should take after a block transfer has completed +// <id> dmac_blockact_0 +#ifndef CONF_DMAC_BLOCKACT_0 +#define CONF_DMAC_BLOCKACT_0 0 +#endif + +// <o> Event Output Selection +// <0=> Event generation disabled +// <1=> Event strobe when block transfer complete +// <3=> Event strobe when beat transfer complete +// <i> Defines the event output selection +// <id> dmac_evosel_0 +#ifndef CONF_DMAC_EVOSEL_0 +#define CONF_DMAC_EVOSEL_0 0 +#endif +// </e> + +// <e> Channel 1 settings +// <id> dmac_channel_1_settings +#ifndef CONF_DMAC_CHANNEL_1_SETTINGS +#define CONF_DMAC_CHANNEL_1_SETTINGS 0 +#endif + +// <q> Channel Enable +// <i> Indicates whether channel 1 is enabled or not +// <id> dmac_enable_1 +#ifndef CONF_DMAC_ENABLE_1 +#define CONF_DMAC_ENABLE_1 0 +#endif + +// <q> Channel Run in Standby +// <i> Indicates whether channel 1 is running in standby mode or not +// <id> dmac_runstdby_1 +#ifndef CONF_DMAC_RUNSTDBY_1 +#define CONF_DMAC_RUNSTDBY_1 0 +#endif + +// <o> Trigger action +// <0=> One trigger required for each block transfer +// <2=> One trigger required for each beat transfer +// <3=> One trigger required for each transaction +// <i> Defines the trigger action used for a transfer +// <id> dmac_trigact_1 +#ifndef CONF_DMAC_TRIGACT_1 +#define CONF_DMAC_TRIGACT_1 0 +#endif + +// <o> Trigger source +// <0x00=> Only software/event triggers +// <0x01=> RTC Timestamp +// <0x02=> SERCOM0 RX Trigger +// <0x03=> SERCOM0 TX Trigger +// <0x04=> SERCOM1 RX Trigger +// <0x05=> SERCOM1 TX Trigger +// <0x06=> SERCOM2 RX Trigger +// <0x07=> SERCOM2 TX Trigger +// <0x08=> SERCOM3 RX Trigger +// <0x09=> SERCOM3 TX Trigger +// <0x0A=> SERCOM4 RX Trigger +// <0x0B=> SERCOM4 TX Trigger +// <0x0C=> SERCOM5 RX Trigger +// <0x0D=> SERCOM5 TX Trigger +// <0x0E=> TCC0 Overflow Trigger +// <0x0F=> TCC0 Match/Compare 0 Trigger +// <0x10=> TCC0 Match/Compare 1 Trigger +// <0x11=> TCC0 Match/Compare 2 Trigger +// <0x12=> TCC0 Match/Compare 3 Trigger +// <0x13=> TC0 Overflow Trigger +// <0x14=> TC0 Match/Compare 0 Trigger +// <0x15=> TC0 Match/Compare 1 Trigger +// <0x16=> TC1 Overflow Trigger +// <0x17=> TC1 Match/Compare 0 Trigger +// <0x18=> TC1 Match/Compare 1 Trigger +// <0x19=> TC2 Overflow Trigger +// <0x1A=> TC2 Match/Compare 0 Trigger +// <0x1B=> TC2 Match/Compare 1 Trigger +// <0x1C=> TC3 Overflow Trigger +// <0x1D=> TC3 Match/Compare 0 Trigger +// <0x1E=> TC3 Match/Compare 1 Trigger +// <0x1F=> ADC Result Ready Trigger +// <0x20=> SLCD Display Memory Update Trigger +// <0x21=> SLCD Automated Character Mapping Data Ready Trigger +// <0x22=> SLCD Automated Bit Mapping Data Ready Trigger +// <0x23=> AES Write Trigger +// <0x24=> AES Read Trigger +// <0x25=> PTC End of Conversion Trigger +// <0x26=> PTC Sequence Trigger +// <0x27=> PTC Window Comparator Trigger +// <i> Defines the peripheral trigger which is source of the transfer +// <id> dmac_trifsrc_1 +#ifndef CONF_DMAC_TRIGSRC_1 +#define CONF_DMAC_TRIGSRC_1 0 +#endif + +// <o> Channel Arbitration Level +// <0=> Channel priority 0 +// <1=> Channel priority 1 +// <2=> Channel priority 2 +// <3=> Channel priority 3 +// <i> Defines the arbitration level for this channel +// <id> dmac_lvl_1 +#ifndef CONF_DMAC_LVL_1 +#define CONF_DMAC_LVL_1 0 +#endif + +// <q> Channel Event Output +// <i> Indicates whether channel event generation is enabled or not +// <id> dmac_evoe_1 +#ifndef CONF_DMAC_EVOE_1 +#define CONF_DMAC_EVOE_1 0 +#endif + +// <q> Channel Event Input +// <i> Indicates whether channel event reception is enabled or not +// <id> dmac_evie_1 +#ifndef CONF_DMAC_EVIE_1 +#define CONF_DMAC_EVIE_1 0 +#endif + +// <o> Event Input Action +// <0=> No action +// <1=> Normal transfer and conditional transfer on strobe trigger +// <2=> Conditional transfer trigger +// <3=> Conditional block transfer +// <4=> Channel suspend operation +// <5=> Channel resume operation +// <6=> Skip next block suspend action +// <i> Defines the event input action +// <id> dmac_evact_1 +#ifndef CONF_DMAC_EVACT_1 +#define CONF_DMAC_EVACT_1 0 +#endif + +// <o> Address Increment Step Size +// <0=> Next ADDR = ADDR + (BEATSIZE + 1) * 1 +// <1=> Next ADDR = ADDR + (BEATSIZE + 1) * 2 +// <2=> Next ADDR = ADDR + (BEATSIZE + 1) * 4 +// <3=> Next ADDR = ADDR + (BEATSIZE + 1) * 8 +// <4=> Next ADDR = ADDR + (BEATSIZE + 1) * 16 +// <5=> Next ADDR = ADDR + (BEATSIZE + 1) * 32 +// <6=> Next ADDR = ADDR + (BEATSIZE + 1) * 64 +// <7=> Next ADDR = ADDR + (BEATSIZE + 1) * 128 +// <i> Defines the address increment step size, applies to source or destination address +// <id> dmac_stepsize_1 +#ifndef CONF_DMAC_STEPSIZE_1 +#define CONF_DMAC_STEPSIZE_1 0 +#endif + +// <o> Step Selection +// <0=> Step size settings apply to the destination address +// <1=> Step size settings apply to the source address +// <i> Defines whether source or destination addresses are using the step size settings +// <id> dmac_stepsel_1 +#ifndef CONF_DMAC_STEPSEL_1 +#define CONF_DMAC_STEPSEL_1 0 +#endif + +// <q> Source Address Increment +// <i> Indicates whether the source address incrementation is enabled or not +// <id> dmac_srcinc_1 +#ifndef CONF_DMAC_SRCINC_1 +#define CONF_DMAC_SRCINC_1 0 +#endif + +// <q> Destination Address Increment +// <i> Indicates whether the destination address incrementation is enabled or not +// <id> dmac_dstinc_1 +#ifndef CONF_DMAC_DSTINC_1 +#define CONF_DMAC_DSTINC_1 0 +#endif + +// <o> Beat Size +// <0=> 8-bit bus transfer +// <1=> 16-bit bus transfer +// <2=> 32-bit bus transfer +// <i> Defines the size of one beat +// <id> dmac_beatsize_1 +#ifndef CONF_DMAC_BEATSIZE_1 +#define CONF_DMAC_BEATSIZE_1 0 +#endif + +// <o> Block Action +// <0=> Channel will be disabled if it is the last block transfer in the transaction +// <1=> Channel will be disabled if it is the last block transfer in the transaction and block interrupt +// <2=> Channel suspend operation is complete +// <3=> Both channel suspend operation and block interrupt +// <i> Defines the the DMAC should take after a block transfer has completed +// <id> dmac_blockact_1 +#ifndef CONF_DMAC_BLOCKACT_1 +#define CONF_DMAC_BLOCKACT_1 0 +#endif + +// <o> Event Output Selection +// <0=> Event generation disabled +// <1=> Event strobe when block transfer complete +// <3=> Event strobe when beat transfer complete +// <i> Defines the event output selection +// <id> dmac_evosel_1 +#ifndef CONF_DMAC_EVOSEL_1 +#define CONF_DMAC_EVOSEL_1 0 +#endif +// </e> + +// <e> Channel 2 settings +// <id> dmac_channel_2_settings +#ifndef CONF_DMAC_CHANNEL_2_SETTINGS +#define CONF_DMAC_CHANNEL_2_SETTINGS 0 +#endif + +// <q> Channel Enable +// <i> Indicates whether channel 2 is enabled or not +// <id> dmac_enable_2 +#ifndef CONF_DMAC_ENABLE_2 +#define CONF_DMAC_ENABLE_2 0 +#endif + +// <q> Channel Run in Standby +// <i> Indicates whether channel 2 is running in standby mode or not +// <id> dmac_runstdby_2 +#ifndef CONF_DMAC_RUNSTDBY_2 +#define CONF_DMAC_RUNSTDBY_2 0 +#endif + +// <o> Trigger action +// <0=> One trigger required for each block transfer +// <2=> One trigger required for each beat transfer +// <3=> One trigger required for each transaction +// <i> Defines the trigger action used for a transfer +// <id> dmac_trigact_2 +#ifndef CONF_DMAC_TRIGACT_2 +#define CONF_DMAC_TRIGACT_2 0 +#endif + +// <o> Trigger source +// <0x00=> Only software/event triggers +// <0x01=> RTC Timestamp +// <0x02=> SERCOM0 RX Trigger +// <0x03=> SERCOM0 TX Trigger +// <0x04=> SERCOM1 RX Trigger +// <0x05=> SERCOM1 TX Trigger +// <0x06=> SERCOM2 RX Trigger +// <0x07=> SERCOM2 TX Trigger +// <0x08=> SERCOM3 RX Trigger +// <0x09=> SERCOM3 TX Trigger +// <0x0A=> SERCOM4 RX Trigger +// <0x0B=> SERCOM4 TX Trigger +// <0x0C=> SERCOM5 RX Trigger +// <0x0D=> SERCOM5 TX Trigger +// <0x0E=> TCC0 Overflow Trigger +// <0x0F=> TCC0 Match/Compare 0 Trigger +// <0x10=> TCC0 Match/Compare 1 Trigger +// <0x11=> TCC0 Match/Compare 2 Trigger +// <0x12=> TCC0 Match/Compare 3 Trigger +// <0x13=> TC0 Overflow Trigger +// <0x14=> TC0 Match/Compare 0 Trigger +// <0x15=> TC0 Match/Compare 1 Trigger +// <0x16=> TC1 Overflow Trigger +// <0x17=> TC1 Match/Compare 0 Trigger +// <0x18=> TC1 Match/Compare 1 Trigger +// <0x19=> TC2 Overflow Trigger +// <0x1A=> TC2 Match/Compare 0 Trigger +// <0x1B=> TC2 Match/Compare 1 Trigger +// <0x1C=> TC3 Overflow Trigger +// <0x1D=> TC3 Match/Compare 0 Trigger +// <0x1E=> TC3 Match/Compare 1 Trigger +// <0x1F=> ADC Result Ready Trigger +// <0x20=> SLCD Display Memory Update Trigger +// <0x21=> SLCD Automated Character Mapping Data Ready Trigger +// <0x22=> SLCD Automated Bit Mapping Data Ready Trigger +// <0x23=> AES Write Trigger +// <0x24=> AES Read Trigger +// <0x25=> PTC End of Conversion Trigger +// <0x26=> PTC Sequence Trigger +// <0x27=> PTC Window Comparator Trigger +// <i> Defines the peripheral trigger which is source of the transfer +// <id> dmac_trifsrc_2 +#ifndef CONF_DMAC_TRIGSRC_2 +#define CONF_DMAC_TRIGSRC_2 0 +#endif + +// <o> Channel Arbitration Level +// <0=> Channel priority 0 +// <1=> Channel priority 1 +// <2=> Channel priority 2 +// <3=> Channel priority 3 +// <i> Defines the arbitration level for this channel +// <id> dmac_lvl_2 +#ifndef CONF_DMAC_LVL_2 +#define CONF_DMAC_LVL_2 0 +#endif + +// <q> Channel Event Output +// <i> Indicates whether channel event generation is enabled or not +// <id> dmac_evoe_2 +#ifndef CONF_DMAC_EVOE_2 +#define CONF_DMAC_EVOE_2 0 +#endif + +// <q> Channel Event Input +// <i> Indicates whether channel event reception is enabled or not +// <id> dmac_evie_2 +#ifndef CONF_DMAC_EVIE_2 +#define CONF_DMAC_EVIE_2 0 +#endif + +// <o> Event Input Action +// <0=> No action +// <1=> Normal transfer and conditional transfer on strobe trigger +// <2=> Conditional transfer trigger +// <3=> Conditional block transfer +// <4=> Channel suspend operation +// <5=> Channel resume operation +// <6=> Skip next block suspend action +// <i> Defines the event input action +// <id> dmac_evact_2 +#ifndef CONF_DMAC_EVACT_2 +#define CONF_DMAC_EVACT_2 0 +#endif + +// <o> Address Increment Step Size +// <0=> Next ADDR = ADDR + (BEATSIZE + 1) * 1 +// <1=> Next ADDR = ADDR + (BEATSIZE + 1) * 2 +// <2=> Next ADDR = ADDR + (BEATSIZE + 1) * 4 +// <3=> Next ADDR = ADDR + (BEATSIZE + 1) * 8 +// <4=> Next ADDR = ADDR + (BEATSIZE + 1) * 16 +// <5=> Next ADDR = ADDR + (BEATSIZE + 1) * 32 +// <6=> Next ADDR = ADDR + (BEATSIZE + 1) * 64 +// <7=> Next ADDR = ADDR + (BEATSIZE + 1) * 128 +// <i> Defines the address increment step size, applies to source or destination address +// <id> dmac_stepsize_2 +#ifndef CONF_DMAC_STEPSIZE_2 +#define CONF_DMAC_STEPSIZE_2 0 +#endif + +// <o> Step Selection +// <0=> Step size settings apply to the destination address +// <1=> Step size settings apply to the source address +// <i> Defines whether source or destination addresses are using the step size settings +// <id> dmac_stepsel_2 +#ifndef CONF_DMAC_STEPSEL_2 +#define CONF_DMAC_STEPSEL_2 0 +#endif + +// <q> Source Address Increment +// <i> Indicates whether the source address incrementation is enabled or not +// <id> dmac_srcinc_2 +#ifndef CONF_DMAC_SRCINC_2 +#define CONF_DMAC_SRCINC_2 0 +#endif + +// <q> Destination Address Increment +// <i> Indicates whether the destination address incrementation is enabled or not +// <id> dmac_dstinc_2 +#ifndef CONF_DMAC_DSTINC_2 +#define CONF_DMAC_DSTINC_2 0 +#endif + +// <o> Beat Size +// <0=> 8-bit bus transfer +// <1=> 16-bit bus transfer +// <2=> 32-bit bus transfer +// <i> Defines the size of one beat +// <id> dmac_beatsize_2 +#ifndef CONF_DMAC_BEATSIZE_2 +#define CONF_DMAC_BEATSIZE_2 0 +#endif + +// <o> Block Action +// <0=> Channel will be disabled if it is the last block transfer in the transaction +// <1=> Channel will be disabled if it is the last block transfer in the transaction and block interrupt +// <2=> Channel suspend operation is complete +// <3=> Both channel suspend operation and block interrupt +// <i> Defines the the DMAC should take after a block transfer has completed +// <id> dmac_blockact_2 +#ifndef CONF_DMAC_BLOCKACT_2 +#define CONF_DMAC_BLOCKACT_2 0 +#endif + +// <o> Event Output Selection +// <0=> Event generation disabled +// <1=> Event strobe when block transfer complete +// <3=> Event strobe when beat transfer complete +// <i> Defines the event output selection +// <id> dmac_evosel_2 +#ifndef CONF_DMAC_EVOSEL_2 +#define CONF_DMAC_EVOSEL_2 0 +#endif +// </e> + +// <e> Channel 3 settings +// <id> dmac_channel_3_settings +#ifndef CONF_DMAC_CHANNEL_3_SETTINGS +#define CONF_DMAC_CHANNEL_3_SETTINGS 0 +#endif + +// <q> Channel Enable +// <i> Indicates whether channel 3 is enabled or not +// <id> dmac_enable_3 +#ifndef CONF_DMAC_ENABLE_3 +#define CONF_DMAC_ENABLE_3 0 +#endif + +// <q> Channel Run in Standby +// <i> Indicates whether channel 3 is running in standby mode or not +// <id> dmac_runstdby_3 +#ifndef CONF_DMAC_RUNSTDBY_3 +#define CONF_DMAC_RUNSTDBY_3 0 +#endif + +// <o> Trigger action +// <0=> One trigger required for each block transfer +// <2=> One trigger required for each beat transfer +// <3=> One trigger required for each transaction +// <i> Defines the trigger action used for a transfer +// <id> dmac_trigact_3 +#ifndef CONF_DMAC_TRIGACT_3 +#define CONF_DMAC_TRIGACT_3 0 +#endif + +// <o> Trigger source +// <0x00=> Only software/event triggers +// <0x01=> RTC Timestamp +// <0x02=> SERCOM0 RX Trigger +// <0x03=> SERCOM0 TX Trigger +// <0x04=> SERCOM1 RX Trigger +// <0x05=> SERCOM1 TX Trigger +// <0x06=> SERCOM2 RX Trigger +// <0x07=> SERCOM2 TX Trigger +// <0x08=> SERCOM3 RX Trigger +// <0x09=> SERCOM3 TX Trigger +// <0x0A=> SERCOM4 RX Trigger +// <0x0B=> SERCOM4 TX Trigger +// <0x0C=> SERCOM5 RX Trigger +// <0x0D=> SERCOM5 TX Trigger +// <0x0E=> TCC0 Overflow Trigger +// <0x0F=> TCC0 Match/Compare 0 Trigger +// <0x10=> TCC0 Match/Compare 1 Trigger +// <0x11=> TCC0 Match/Compare 2 Trigger +// <0x12=> TCC0 Match/Compare 3 Trigger +// <0x13=> TC0 Overflow Trigger +// <0x14=> TC0 Match/Compare 0 Trigger +// <0x15=> TC0 Match/Compare 1 Trigger +// <0x16=> TC1 Overflow Trigger +// <0x17=> TC1 Match/Compare 0 Trigger +// <0x18=> TC1 Match/Compare 1 Trigger +// <0x19=> TC2 Overflow Trigger +// <0x1A=> TC2 Match/Compare 0 Trigger +// <0x1B=> TC2 Match/Compare 1 Trigger +// <0x1C=> TC3 Overflow Trigger +// <0x1D=> TC3 Match/Compare 0 Trigger +// <0x1E=> TC3 Match/Compare 1 Trigger +// <0x1F=> ADC Result Ready Trigger +// <0x20=> SLCD Display Memory Update Trigger +// <0x21=> SLCD Automated Character Mapping Data Ready Trigger +// <0x22=> SLCD Automated Bit Mapping Data Ready Trigger +// <0x23=> AES Write Trigger +// <0x24=> AES Read Trigger +// <0x25=> PTC End of Conversion Trigger +// <0x26=> PTC Sequence Trigger +// <0x27=> PTC Window Comparator Trigger +// <i> Defines the peripheral trigger which is source of the transfer +// <id> dmac_trifsrc_3 +#ifndef CONF_DMAC_TRIGSRC_3 +#define CONF_DMAC_TRIGSRC_3 0 +#endif + +// <o> Channel Arbitration Level +// <0=> Channel priority 0 +// <1=> Channel priority 1 +// <2=> Channel priority 2 +// <3=> Channel priority 3 +// <i> Defines the arbitration level for this channel +// <id> dmac_lvl_3 +#ifndef CONF_DMAC_LVL_3 +#define CONF_DMAC_LVL_3 0 +#endif + +// <q> Channel Event Output +// <i> Indicates whether channel event generation is enabled or not +// <id> dmac_evoe_3 +#ifndef CONF_DMAC_EVOE_3 +#define CONF_DMAC_EVOE_3 0 +#endif + +// <q> Channel Event Input +// <i> Indicates whether channel event reception is enabled or not +// <id> dmac_evie_3 +#ifndef CONF_DMAC_EVIE_3 +#define CONF_DMAC_EVIE_3 0 +#endif + +// <o> Event Input Action +// <0=> No action +// <1=> Normal transfer and conditional transfer on strobe trigger +// <2=> Conditional transfer trigger +// <3=> Conditional block transfer +// <4=> Channel suspend operation +// <5=> Channel resume operation +// <6=> Skip next block suspend action +// <i> Defines the event input action +// <id> dmac_evact_3 +#ifndef CONF_DMAC_EVACT_3 +#define CONF_DMAC_EVACT_3 0 +#endif + +// <o> Address Increment Step Size +// <0=> Next ADDR = ADDR + (BEATSIZE + 1) * 1 +// <1=> Next ADDR = ADDR + (BEATSIZE + 1) * 2 +// <2=> Next ADDR = ADDR + (BEATSIZE + 1) * 4 +// <3=> Next ADDR = ADDR + (BEATSIZE + 1) * 8 +// <4=> Next ADDR = ADDR + (BEATSIZE + 1) * 16 +// <5=> Next ADDR = ADDR + (BEATSIZE + 1) * 32 +// <6=> Next ADDR = ADDR + (BEATSIZE + 1) * 64 +// <7=> Next ADDR = ADDR + (BEATSIZE + 1) * 128 +// <i> Defines the address increment step size, applies to source or destination address +// <id> dmac_stepsize_3 +#ifndef CONF_DMAC_STEPSIZE_3 +#define CONF_DMAC_STEPSIZE_3 0 +#endif + +// <o> Step Selection +// <0=> Step size settings apply to the destination address +// <1=> Step size settings apply to the source address +// <i> Defines whether source or destination addresses are using the step size settings +// <id> dmac_stepsel_3 +#ifndef CONF_DMAC_STEPSEL_3 +#define CONF_DMAC_STEPSEL_3 0 +#endif + +// <q> Source Address Increment +// <i> Indicates whether the source address incrementation is enabled or not +// <id> dmac_srcinc_3 +#ifndef CONF_DMAC_SRCINC_3 +#define CONF_DMAC_SRCINC_3 0 +#endif + +// <q> Destination Address Increment +// <i> Indicates whether the destination address incrementation is enabled or not +// <id> dmac_dstinc_3 +#ifndef CONF_DMAC_DSTINC_3 +#define CONF_DMAC_DSTINC_3 0 +#endif + +// <o> Beat Size +// <0=> 8-bit bus transfer +// <1=> 16-bit bus transfer +// <2=> 32-bit bus transfer +// <i> Defines the size of one beat +// <id> dmac_beatsize_3 +#ifndef CONF_DMAC_BEATSIZE_3 +#define CONF_DMAC_BEATSIZE_3 0 +#endif + +// <o> Block Action +// <0=> Channel will be disabled if it is the last block transfer in the transaction +// <1=> Channel will be disabled if it is the last block transfer in the transaction and block interrupt +// <2=> Channel suspend operation is complete +// <3=> Both channel suspend operation and block interrupt +// <i> Defines the the DMAC should take after a block transfer has completed +// <id> dmac_blockact_3 +#ifndef CONF_DMAC_BLOCKACT_3 +#define CONF_DMAC_BLOCKACT_3 0 +#endif + +// <o> Event Output Selection +// <0=> Event generation disabled +// <1=> Event strobe when block transfer complete +// <3=> Event strobe when beat transfer complete +// <i> Defines the event output selection +// <id> dmac_evosel_3 +#ifndef CONF_DMAC_EVOSEL_3 +#define CONF_DMAC_EVOSEL_3 0 +#endif +// </e> + +// <e> Channel 4 settings +// <id> dmac_channel_4_settings +#ifndef CONF_DMAC_CHANNEL_4_SETTINGS +#define CONF_DMAC_CHANNEL_4_SETTINGS 0 +#endif + +// <q> Channel Enable +// <i> Indicates whether channel 4 is enabled or not +// <id> dmac_enable_4 +#ifndef CONF_DMAC_ENABLE_4 +#define CONF_DMAC_ENABLE_4 0 +#endif + +// <q> Channel Run in Standby +// <i> Indicates whether channel 4 is running in standby mode or not +// <id> dmac_runstdby_4 +#ifndef CONF_DMAC_RUNSTDBY_4 +#define CONF_DMAC_RUNSTDBY_4 0 +#endif + +// <o> Trigger action +// <0=> One trigger required for each block transfer +// <2=> One trigger required for each beat transfer +// <3=> One trigger required for each transaction +// <i> Defines the trigger action used for a transfer +// <id> dmac_trigact_4 +#ifndef CONF_DMAC_TRIGACT_4 +#define CONF_DMAC_TRIGACT_4 0 +#endif + +// <o> Trigger source +// <0x00=> Only software/event triggers +// <0x01=> RTC Timestamp +// <0x02=> SERCOM0 RX Trigger +// <0x03=> SERCOM0 TX Trigger +// <0x04=> SERCOM1 RX Trigger +// <0x05=> SERCOM1 TX Trigger +// <0x06=> SERCOM2 RX Trigger +// <0x07=> SERCOM2 TX Trigger +// <0x08=> SERCOM3 RX Trigger +// <0x09=> SERCOM3 TX Trigger +// <0x0A=> SERCOM4 RX Trigger +// <0x0B=> SERCOM4 TX Trigger +// <0x0C=> SERCOM5 RX Trigger +// <0x0D=> SERCOM5 TX Trigger +// <0x0E=> TCC0 Overflow Trigger +// <0x0F=> TCC0 Match/Compare 0 Trigger +// <0x10=> TCC0 Match/Compare 1 Trigger +// <0x11=> TCC0 Match/Compare 2 Trigger +// <0x12=> TCC0 Match/Compare 3 Trigger +// <0x13=> TC0 Overflow Trigger +// <0x14=> TC0 Match/Compare 0 Trigger +// <0x15=> TC0 Match/Compare 1 Trigger +// <0x16=> TC1 Overflow Trigger +// <0x17=> TC1 Match/Compare 0 Trigger +// <0x18=> TC1 Match/Compare 1 Trigger +// <0x19=> TC2 Overflow Trigger +// <0x1A=> TC2 Match/Compare 0 Trigger +// <0x1B=> TC2 Match/Compare 1 Trigger +// <0x1C=> TC3 Overflow Trigger +// <0x1D=> TC3 Match/Compare 0 Trigger +// <0x1E=> TC3 Match/Compare 1 Trigger +// <0x1F=> ADC Result Ready Trigger +// <0x20=> SLCD Display Memory Update Trigger +// <0x21=> SLCD Automated Character Mapping Data Ready Trigger +// <0x22=> SLCD Automated Bit Mapping Data Ready Trigger +// <0x23=> AES Write Trigger +// <0x24=> AES Read Trigger +// <0x25=> PTC End of Conversion Trigger +// <0x26=> PTC Sequence Trigger +// <0x27=> PTC Window Comparator Trigger +// <i> Defines the peripheral trigger which is source of the transfer +// <id> dmac_trifsrc_4 +#ifndef CONF_DMAC_TRIGSRC_4 +#define CONF_DMAC_TRIGSRC_4 0 +#endif + +// <o> Channel Arbitration Level +// <0=> Channel priority 0 +// <1=> Channel priority 1 +// <2=> Channel priority 2 +// <3=> Channel priority 3 +// <i> Defines the arbitration level for this channel +// <id> dmac_lvl_4 +#ifndef CONF_DMAC_LVL_4 +#define CONF_DMAC_LVL_4 0 +#endif + +// <q> Channel Event Output +// <i> Indicates whether channel event generation is enabled or not +// <id> dmac_evoe_4 +#ifndef CONF_DMAC_EVOE_4 +#define CONF_DMAC_EVOE_4 0 +#endif + +// <q> Channel Event Input +// <i> Indicates whether channel event reception is enabled or not +// <id> dmac_evie_4 +#ifndef CONF_DMAC_EVIE_4 +#define CONF_DMAC_EVIE_4 0 +#endif + +// <o> Event Input Action +// <0=> No action +// <1=> Normal transfer and conditional transfer on strobe trigger +// <2=> Conditional transfer trigger +// <3=> Conditional block transfer +// <4=> Channel suspend operation +// <5=> Channel resume operation +// <6=> Skip next block suspend action +// <i> Defines the event input action +// <id> dmac_evact_4 +#ifndef CONF_DMAC_EVACT_4 +#define CONF_DMAC_EVACT_4 0 +#endif + +// <o> Address Increment Step Size +// <0=> Next ADDR = ADDR + (BEATSIZE + 1) * 1 +// <1=> Next ADDR = ADDR + (BEATSIZE + 1) * 2 +// <2=> Next ADDR = ADDR + (BEATSIZE + 1) * 4 +// <3=> Next ADDR = ADDR + (BEATSIZE + 1) * 8 +// <4=> Next ADDR = ADDR + (BEATSIZE + 1) * 16 +// <5=> Next ADDR = ADDR + (BEATSIZE + 1) * 32 +// <6=> Next ADDR = ADDR + (BEATSIZE + 1) * 64 +// <7=> Next ADDR = ADDR + (BEATSIZE + 1) * 128 +// <i> Defines the address increment step size, applies to source or destination address +// <id> dmac_stepsize_4 +#ifndef CONF_DMAC_STEPSIZE_4 +#define CONF_DMAC_STEPSIZE_4 0 +#endif + +// <o> Step Selection +// <0=> Step size settings apply to the destination address +// <1=> Step size settings apply to the source address +// <i> Defines whether source or destination addresses are using the step size settings +// <id> dmac_stepsel_4 +#ifndef CONF_DMAC_STEPSEL_4 +#define CONF_DMAC_STEPSEL_4 0 +#endif + +// <q> Source Address Increment +// <i> Indicates whether the source address incrementation is enabled or not +// <id> dmac_srcinc_4 +#ifndef CONF_DMAC_SRCINC_4 +#define CONF_DMAC_SRCINC_4 0 +#endif + +// <q> Destination Address Increment +// <i> Indicates whether the destination address incrementation is enabled or not +// <id> dmac_dstinc_4 +#ifndef CONF_DMAC_DSTINC_4 +#define CONF_DMAC_DSTINC_4 0 +#endif + +// <o> Beat Size +// <0=> 8-bit bus transfer +// <1=> 16-bit bus transfer +// <2=> 32-bit bus transfer +// <i> Defines the size of one beat +// <id> dmac_beatsize_4 +#ifndef CONF_DMAC_BEATSIZE_4 +#define CONF_DMAC_BEATSIZE_4 0 +#endif + +// <o> Block Action +// <0=> Channel will be disabled if it is the last block transfer in the transaction +// <1=> Channel will be disabled if it is the last block transfer in the transaction and block interrupt +// <2=> Channel suspend operation is complete +// <3=> Both channel suspend operation and block interrupt +// <i> Defines the the DMAC should take after a block transfer has completed +// <id> dmac_blockact_4 +#ifndef CONF_DMAC_BLOCKACT_4 +#define CONF_DMAC_BLOCKACT_4 0 +#endif + +// <o> Event Output Selection +// <0=> Event generation disabled +// <1=> Event strobe when block transfer complete +// <3=> Event strobe when beat transfer complete +// <i> Defines the event output selection +// <id> dmac_evosel_4 +#ifndef CONF_DMAC_EVOSEL_4 +#define CONF_DMAC_EVOSEL_4 0 +#endif +// </e> + +// <e> Channel 5 settings +// <id> dmac_channel_5_settings +#ifndef CONF_DMAC_CHANNEL_5_SETTINGS +#define CONF_DMAC_CHANNEL_5_SETTINGS 0 +#endif + +// <q> Channel Enable +// <i> Indicates whether channel 5 is enabled or not +// <id> dmac_enable_5 +#ifndef CONF_DMAC_ENABLE_5 +#define CONF_DMAC_ENABLE_5 0 +#endif + +// <q> Channel Run in Standby +// <i> Indicates whether channel 5 is running in standby mode or not +// <id> dmac_runstdby_5 +#ifndef CONF_DMAC_RUNSTDBY_5 +#define CONF_DMAC_RUNSTDBY_5 0 +#endif + +// <o> Trigger action +// <0=> One trigger required for each block transfer +// <2=> One trigger required for each beat transfer +// <3=> One trigger required for each transaction +// <i> Defines the trigger action used for a transfer +// <id> dmac_trigact_5 +#ifndef CONF_DMAC_TRIGACT_5 +#define CONF_DMAC_TRIGACT_5 0 +#endif + +// <o> Trigger source +// <0x00=> Only software/event triggers +// <0x01=> RTC Timestamp +// <0x02=> SERCOM0 RX Trigger +// <0x03=> SERCOM0 TX Trigger +// <0x04=> SERCOM1 RX Trigger +// <0x05=> SERCOM1 TX Trigger +// <0x06=> SERCOM2 RX Trigger +// <0x07=> SERCOM2 TX Trigger +// <0x08=> SERCOM3 RX Trigger +// <0x09=> SERCOM3 TX Trigger +// <0x0A=> SERCOM4 RX Trigger +// <0x0B=> SERCOM4 TX Trigger +// <0x0C=> SERCOM5 RX Trigger +// <0x0D=> SERCOM5 TX Trigger +// <0x0E=> TCC0 Overflow Trigger +// <0x0F=> TCC0 Match/Compare 0 Trigger +// <0x10=> TCC0 Match/Compare 1 Trigger +// <0x11=> TCC0 Match/Compare 2 Trigger +// <0x12=> TCC0 Match/Compare 3 Trigger +// <0x13=> TC0 Overflow Trigger +// <0x14=> TC0 Match/Compare 0 Trigger +// <0x15=> TC0 Match/Compare 1 Trigger +// <0x16=> TC1 Overflow Trigger +// <0x17=> TC1 Match/Compare 0 Trigger +// <0x18=> TC1 Match/Compare 1 Trigger +// <0x19=> TC2 Overflow Trigger +// <0x1A=> TC2 Match/Compare 0 Trigger +// <0x1B=> TC2 Match/Compare 1 Trigger +// <0x1C=> TC3 Overflow Trigger +// <0x1D=> TC3 Match/Compare 0 Trigger +// <0x1E=> TC3 Match/Compare 1 Trigger +// <0x1F=> ADC Result Ready Trigger +// <0x20=> SLCD Display Memory Update Trigger +// <0x21=> SLCD Automated Character Mapping Data Ready Trigger +// <0x22=> SLCD Automated Bit Mapping Data Ready Trigger +// <0x23=> AES Write Trigger +// <0x24=> AES Read Trigger +// <0x25=> PTC End of Conversion Trigger +// <0x26=> PTC Sequence Trigger +// <0x27=> PTC Window Comparator Trigger +// <i> Defines the peripheral trigger which is source of the transfer +// <id> dmac_trifsrc_5 +#ifndef CONF_DMAC_TRIGSRC_5 +#define CONF_DMAC_TRIGSRC_5 0 +#endif + +// <o> Channel Arbitration Level +// <0=> Channel priority 0 +// <1=> Channel priority 1 +// <2=> Channel priority 2 +// <3=> Channel priority 3 +// <i> Defines the arbitration level for this channel +// <id> dmac_lvl_5 +#ifndef CONF_DMAC_LVL_5 +#define CONF_DMAC_LVL_5 0 +#endif + +// <q> Channel Event Output +// <i> Indicates whether channel event generation is enabled or not +// <id> dmac_evoe_5 +#ifndef CONF_DMAC_EVOE_5 +#define CONF_DMAC_EVOE_5 0 +#endif + +// <q> Channel Event Input +// <i> Indicates whether channel event reception is enabled or not +// <id> dmac_evie_5 +#ifndef CONF_DMAC_EVIE_5 +#define CONF_DMAC_EVIE_5 0 +#endif + +// <o> Event Input Action +// <0=> No action +// <1=> Normal transfer and conditional transfer on strobe trigger +// <2=> Conditional transfer trigger +// <3=> Conditional block transfer +// <4=> Channel suspend operation +// <5=> Channel resume operation +// <6=> Skip next block suspend action +// <i> Defines the event input action +// <id> dmac_evact_5 +#ifndef CONF_DMAC_EVACT_5 +#define CONF_DMAC_EVACT_5 0 +#endif + +// <o> Address Increment Step Size +// <0=> Next ADDR = ADDR + (BEATSIZE + 1) * 1 +// <1=> Next ADDR = ADDR + (BEATSIZE + 1) * 2 +// <2=> Next ADDR = ADDR + (BEATSIZE + 1) * 4 +// <3=> Next ADDR = ADDR + (BEATSIZE + 1) * 8 +// <4=> Next ADDR = ADDR + (BEATSIZE + 1) * 16 +// <5=> Next ADDR = ADDR + (BEATSIZE + 1) * 32 +// <6=> Next ADDR = ADDR + (BEATSIZE + 1) * 64 +// <7=> Next ADDR = ADDR + (BEATSIZE + 1) * 128 +// <i> Defines the address increment step size, applies to source or destination address +// <id> dmac_stepsize_5 +#ifndef CONF_DMAC_STEPSIZE_5 +#define CONF_DMAC_STEPSIZE_5 0 +#endif + +// <o> Step Selection +// <0=> Step size settings apply to the destination address +// <1=> Step size settings apply to the source address +// <i> Defines whether source or destination addresses are using the step size settings +// <id> dmac_stepsel_5 +#ifndef CONF_DMAC_STEPSEL_5 +#define CONF_DMAC_STEPSEL_5 0 +#endif + +// <q> Source Address Increment +// <i> Indicates whether the source address incrementation is enabled or not +// <id> dmac_srcinc_5 +#ifndef CONF_DMAC_SRCINC_5 +#define CONF_DMAC_SRCINC_5 0 +#endif + +// <q> Destination Address Increment +// <i> Indicates whether the destination address incrementation is enabled or not +// <id> dmac_dstinc_5 +#ifndef CONF_DMAC_DSTINC_5 +#define CONF_DMAC_DSTINC_5 0 +#endif + +// <o> Beat Size +// <0=> 8-bit bus transfer +// <1=> 16-bit bus transfer +// <2=> 32-bit bus transfer +// <i> Defines the size of one beat +// <id> dmac_beatsize_5 +#ifndef CONF_DMAC_BEATSIZE_5 +#define CONF_DMAC_BEATSIZE_5 0 +#endif + +// <o> Block Action +// <0=> Channel will be disabled if it is the last block transfer in the transaction +// <1=> Channel will be disabled if it is the last block transfer in the transaction and block interrupt +// <2=> Channel suspend operation is complete +// <3=> Both channel suspend operation and block interrupt +// <i> Defines the the DMAC should take after a block transfer has completed +// <id> dmac_blockact_5 +#ifndef CONF_DMAC_BLOCKACT_5 +#define CONF_DMAC_BLOCKACT_5 0 +#endif + +// <o> Event Output Selection +// <0=> Event generation disabled +// <1=> Event strobe when block transfer complete +// <3=> Event strobe when beat transfer complete +// <i> Defines the event output selection +// <id> dmac_evosel_5 +#ifndef CONF_DMAC_EVOSEL_5 +#define CONF_DMAC_EVOSEL_5 0 +#endif +// </e> + +// <e> Channel 6 settings +// <id> dmac_channel_6_settings +#ifndef CONF_DMAC_CHANNEL_6_SETTINGS +#define CONF_DMAC_CHANNEL_6_SETTINGS 0 +#endif + +// <q> Channel Enable +// <i> Indicates whether channel 6 is enabled or not +// <id> dmac_enable_6 +#ifndef CONF_DMAC_ENABLE_6 +#define CONF_DMAC_ENABLE_6 0 +#endif + +// <q> Channel Run in Standby +// <i> Indicates whether channel 6 is running in standby mode or not +// <id> dmac_runstdby_6 +#ifndef CONF_DMAC_RUNSTDBY_6 +#define CONF_DMAC_RUNSTDBY_6 0 +#endif + +// <o> Trigger action +// <0=> One trigger required for each block transfer +// <2=> One trigger required for each beat transfer +// <3=> One trigger required for each transaction +// <i> Defines the trigger action used for a transfer +// <id> dmac_trigact_6 +#ifndef CONF_DMAC_TRIGACT_6 +#define CONF_DMAC_TRIGACT_6 0 +#endif + +// <o> Trigger source +// <0x00=> Only software/event triggers +// <0x01=> RTC Timestamp +// <0x02=> SERCOM0 RX Trigger +// <0x03=> SERCOM0 TX Trigger +// <0x04=> SERCOM1 RX Trigger +// <0x05=> SERCOM1 TX Trigger +// <0x06=> SERCOM2 RX Trigger +// <0x07=> SERCOM2 TX Trigger +// <0x08=> SERCOM3 RX Trigger +// <0x09=> SERCOM3 TX Trigger +// <0x0A=> SERCOM4 RX Trigger +// <0x0B=> SERCOM4 TX Trigger +// <0x0C=> SERCOM5 RX Trigger +// <0x0D=> SERCOM5 TX Trigger +// <0x0E=> TCC0 Overflow Trigger +// <0x0F=> TCC0 Match/Compare 0 Trigger +// <0x10=> TCC0 Match/Compare 1 Trigger +// <0x11=> TCC0 Match/Compare 2 Trigger +// <0x12=> TCC0 Match/Compare 3 Trigger +// <0x13=> TC0 Overflow Trigger +// <0x14=> TC0 Match/Compare 0 Trigger +// <0x15=> TC0 Match/Compare 1 Trigger +// <0x16=> TC1 Overflow Trigger +// <0x17=> TC1 Match/Compare 0 Trigger +// <0x18=> TC1 Match/Compare 1 Trigger +// <0x19=> TC2 Overflow Trigger +// <0x1A=> TC2 Match/Compare 0 Trigger +// <0x1B=> TC2 Match/Compare 1 Trigger +// <0x1C=> TC3 Overflow Trigger +// <0x1D=> TC3 Match/Compare 0 Trigger +// <0x1E=> TC3 Match/Compare 1 Trigger +// <0x1F=> ADC Result Ready Trigger +// <0x20=> SLCD Display Memory Update Trigger +// <0x21=> SLCD Automated Character Mapping Data Ready Trigger +// <0x22=> SLCD Automated Bit Mapping Data Ready Trigger +// <0x23=> AES Write Trigger +// <0x24=> AES Read Trigger +// <0x25=> PTC End of Conversion Trigger +// <0x26=> PTC Sequence Trigger +// <0x27=> PTC Window Comparator Trigger +// <i> Defines the peripheral trigger which is source of the transfer +// <id> dmac_trifsrc_6 +#ifndef CONF_DMAC_TRIGSRC_6 +#define CONF_DMAC_TRIGSRC_6 0 +#endif + +// <o> Channel Arbitration Level +// <0=> Channel priority 0 +// <1=> Channel priority 1 +// <2=> Channel priority 2 +// <3=> Channel priority 3 +// <i> Defines the arbitration level for this channel +// <id> dmac_lvl_6 +#ifndef CONF_DMAC_LVL_6 +#define CONF_DMAC_LVL_6 0 +#endif + +// <q> Channel Event Output +// <i> Indicates whether channel event generation is enabled or not +// <id> dmac_evoe_6 +#ifndef CONF_DMAC_EVOE_6 +#define CONF_DMAC_EVOE_6 0 +#endif + +// <q> Channel Event Input +// <i> Indicates whether channel event reception is enabled or not +// <id> dmac_evie_6 +#ifndef CONF_DMAC_EVIE_6 +#define CONF_DMAC_EVIE_6 0 +#endif + +// <o> Event Input Action +// <0=> No action +// <1=> Normal transfer and conditional transfer on strobe trigger +// <2=> Conditional transfer trigger +// <3=> Conditional block transfer +// <4=> Channel suspend operation +// <5=> Channel resume operation +// <6=> Skip next block suspend action +// <i> Defines the event input action +// <id> dmac_evact_6 +#ifndef CONF_DMAC_EVACT_6 +#define CONF_DMAC_EVACT_6 0 +#endif + +// <o> Address Increment Step Size +// <0=> Next ADDR = ADDR + (BEATSIZE + 1) * 1 +// <1=> Next ADDR = ADDR + (BEATSIZE + 1) * 2 +// <2=> Next ADDR = ADDR + (BEATSIZE + 1) * 4 +// <3=> Next ADDR = ADDR + (BEATSIZE + 1) * 8 +// <4=> Next ADDR = ADDR + (BEATSIZE + 1) * 16 +// <5=> Next ADDR = ADDR + (BEATSIZE + 1) * 32 +// <6=> Next ADDR = ADDR + (BEATSIZE + 1) * 64 +// <7=> Next ADDR = ADDR + (BEATSIZE + 1) * 128 +// <i> Defines the address increment step size, applies to source or destination address +// <id> dmac_stepsize_6 +#ifndef CONF_DMAC_STEPSIZE_6 +#define CONF_DMAC_STEPSIZE_6 0 +#endif + +// <o> Step Selection +// <0=> Step size settings apply to the destination address +// <1=> Step size settings apply to the source address +// <i> Defines whether source or destination addresses are using the step size settings +// <id> dmac_stepsel_6 +#ifndef CONF_DMAC_STEPSEL_6 +#define CONF_DMAC_STEPSEL_6 0 +#endif + +// <q> Source Address Increment +// <i> Indicates whether the source address incrementation is enabled or not +// <id> dmac_srcinc_6 +#ifndef CONF_DMAC_SRCINC_6 +#define CONF_DMAC_SRCINC_6 0 +#endif + +// <q> Destination Address Increment +// <i> Indicates whether the destination address incrementation is enabled or not +// <id> dmac_dstinc_6 +#ifndef CONF_DMAC_DSTINC_6 +#define CONF_DMAC_DSTINC_6 0 +#endif + +// <o> Beat Size +// <0=> 8-bit bus transfer +// <1=> 16-bit bus transfer +// <2=> 32-bit bus transfer +// <i> Defines the size of one beat +// <id> dmac_beatsize_6 +#ifndef CONF_DMAC_BEATSIZE_6 +#define CONF_DMAC_BEATSIZE_6 0 +#endif + +// <o> Block Action +// <0=> Channel will be disabled if it is the last block transfer in the transaction +// <1=> Channel will be disabled if it is the last block transfer in the transaction and block interrupt +// <2=> Channel suspend operation is complete +// <3=> Both channel suspend operation and block interrupt +// <i> Defines the the DMAC should take after a block transfer has completed +// <id> dmac_blockact_6 +#ifndef CONF_DMAC_BLOCKACT_6 +#define CONF_DMAC_BLOCKACT_6 0 +#endif + +// <o> Event Output Selection +// <0=> Event generation disabled +// <1=> Event strobe when block transfer complete +// <3=> Event strobe when beat transfer complete +// <i> Defines the event output selection +// <id> dmac_evosel_6 +#ifndef CONF_DMAC_EVOSEL_6 +#define CONF_DMAC_EVOSEL_6 0 +#endif +// </e> + +// <e> Channel 7 settings +// <id> dmac_channel_7_settings +#ifndef CONF_DMAC_CHANNEL_7_SETTINGS +#define CONF_DMAC_CHANNEL_7_SETTINGS 0 +#endif + +// <q> Channel Enable +// <i> Indicates whether channel 7 is enabled or not +// <id> dmac_enable_7 +#ifndef CONF_DMAC_ENABLE_7 +#define CONF_DMAC_ENABLE_7 0 +#endif + +// <q> Channel Run in Standby +// <i> Indicates whether channel 7 is running in standby mode or not +// <id> dmac_runstdby_7 +#ifndef CONF_DMAC_RUNSTDBY_7 +#define CONF_DMAC_RUNSTDBY_7 0 +#endif + +// <o> Trigger action +// <0=> One trigger required for each block transfer +// <2=> One trigger required for each beat transfer +// <3=> One trigger required for each transaction +// <i> Defines the trigger action used for a transfer +// <id> dmac_trigact_7 +#ifndef CONF_DMAC_TRIGACT_7 +#define CONF_DMAC_TRIGACT_7 0 +#endif + +// <o> Trigger source +// <0x00=> Only software/event triggers +// <0x01=> RTC Timestamp +// <0x02=> SERCOM0 RX Trigger +// <0x03=> SERCOM0 TX Trigger +// <0x04=> SERCOM1 RX Trigger +// <0x05=> SERCOM1 TX Trigger +// <0x06=> SERCOM2 RX Trigger +// <0x07=> SERCOM2 TX Trigger +// <0x08=> SERCOM3 RX Trigger +// <0x09=> SERCOM3 TX Trigger +// <0x0A=> SERCOM4 RX Trigger +// <0x0B=> SERCOM4 TX Trigger +// <0x0C=> SERCOM5 RX Trigger +// <0x0D=> SERCOM5 TX Trigger +// <0x0E=> TCC0 Overflow Trigger +// <0x0F=> TCC0 Match/Compare 0 Trigger +// <0x10=> TCC0 Match/Compare 1 Trigger +// <0x11=> TCC0 Match/Compare 2 Trigger +// <0x12=> TCC0 Match/Compare 3 Trigger +// <0x13=> TC0 Overflow Trigger +// <0x14=> TC0 Match/Compare 0 Trigger +// <0x15=> TC0 Match/Compare 1 Trigger +// <0x16=> TC1 Overflow Trigger +// <0x17=> TC1 Match/Compare 0 Trigger +// <0x18=> TC1 Match/Compare 1 Trigger +// <0x19=> TC2 Overflow Trigger +// <0x1A=> TC2 Match/Compare 0 Trigger +// <0x1B=> TC2 Match/Compare 1 Trigger +// <0x1C=> TC3 Overflow Trigger +// <0x1D=> TC3 Match/Compare 0 Trigger +// <0x1E=> TC3 Match/Compare 1 Trigger +// <0x1F=> ADC Result Ready Trigger +// <0x20=> SLCD Display Memory Update Trigger +// <0x21=> SLCD Automated Character Mapping Data Ready Trigger +// <0x22=> SLCD Automated Bit Mapping Data Ready Trigger +// <0x23=> AES Write Trigger +// <0x24=> AES Read Trigger +// <0x25=> PTC End of Conversion Trigger +// <0x26=> PTC Sequence Trigger +// <0x27=> PTC Window Comparator Trigger +// <i> Defines the peripheral trigger which is source of the transfer +// <id> dmac_trifsrc_7 +#ifndef CONF_DMAC_TRIGSRC_7 +#define CONF_DMAC_TRIGSRC_7 0 +#endif + +// <o> Channel Arbitration Level +// <0=> Channel priority 0 +// <1=> Channel priority 1 +// <2=> Channel priority 2 +// <3=> Channel priority 3 +// <i> Defines the arbitration level for this channel +// <id> dmac_lvl_7 +#ifndef CONF_DMAC_LVL_7 +#define CONF_DMAC_LVL_7 0 +#endif + +// <q> Channel Event Output +// <i> Indicates whether channel event generation is enabled or not +// <id> dmac_evoe_7 +#ifndef CONF_DMAC_EVOE_7 +#define CONF_DMAC_EVOE_7 0 +#endif + +// <q> Channel Event Input +// <i> Indicates whether channel event reception is enabled or not +// <id> dmac_evie_7 +#ifndef CONF_DMAC_EVIE_7 +#define CONF_DMAC_EVIE_7 0 +#endif + +// <o> Event Input Action +// <0=> No action +// <1=> Normal transfer and conditional transfer on strobe trigger +// <2=> Conditional transfer trigger +// <3=> Conditional block transfer +// <4=> Channel suspend operation +// <5=> Channel resume operation +// <6=> Skip next block suspend action +// <i> Defines the event input action +// <id> dmac_evact_7 +#ifndef CONF_DMAC_EVACT_7 +#define CONF_DMAC_EVACT_7 0 +#endif + +// <o> Address Increment Step Size +// <0=> Next ADDR = ADDR + (BEATSIZE + 1) * 1 +// <1=> Next ADDR = ADDR + (BEATSIZE + 1) * 2 +// <2=> Next ADDR = ADDR + (BEATSIZE + 1) * 4 +// <3=> Next ADDR = ADDR + (BEATSIZE + 1) * 8 +// <4=> Next ADDR = ADDR + (BEATSIZE + 1) * 16 +// <5=> Next ADDR = ADDR + (BEATSIZE + 1) * 32 +// <6=> Next ADDR = ADDR + (BEATSIZE + 1) * 64 +// <7=> Next ADDR = ADDR + (BEATSIZE + 1) * 128 +// <i> Defines the address increment step size, applies to source or destination address +// <id> dmac_stepsize_7 +#ifndef CONF_DMAC_STEPSIZE_7 +#define CONF_DMAC_STEPSIZE_7 0 +#endif + +// <o> Step Selection +// <0=> Step size settings apply to the destination address +// <1=> Step size settings apply to the source address +// <i> Defines whether source or destination addresses are using the step size settings +// <id> dmac_stepsel_7 +#ifndef CONF_DMAC_STEPSEL_7 +#define CONF_DMAC_STEPSEL_7 0 +#endif + +// <q> Source Address Increment +// <i> Indicates whether the source address incrementation is enabled or not +// <id> dmac_srcinc_7 +#ifndef CONF_DMAC_SRCINC_7 +#define CONF_DMAC_SRCINC_7 0 +#endif + +// <q> Destination Address Increment +// <i> Indicates whether the destination address incrementation is enabled or not +// <id> dmac_dstinc_7 +#ifndef CONF_DMAC_DSTINC_7 +#define CONF_DMAC_DSTINC_7 0 +#endif + +// <o> Beat Size +// <0=> 8-bit bus transfer +// <1=> 16-bit bus transfer +// <2=> 32-bit bus transfer +// <i> Defines the size of one beat +// <id> dmac_beatsize_7 +#ifndef CONF_DMAC_BEATSIZE_7 +#define CONF_DMAC_BEATSIZE_7 0 +#endif + +// <o> Block Action +// <0=> Channel will be disabled if it is the last block transfer in the transaction +// <1=> Channel will be disabled if it is the last block transfer in the transaction and block interrupt +// <2=> Channel suspend operation is complete +// <3=> Both channel suspend operation and block interrupt +// <i> Defines the the DMAC should take after a block transfer has completed +// <id> dmac_blockact_7 +#ifndef CONF_DMAC_BLOCKACT_7 +#define CONF_DMAC_BLOCKACT_7 0 +#endif + +// <o> Event Output Selection +// <0=> Event generation disabled +// <1=> Event strobe when block transfer complete +// <3=> Event strobe when beat transfer complete +// <i> Defines the event output selection +// <id> dmac_evosel_7 +#ifndef CONF_DMAC_EVOSEL_7 +#define CONF_DMAC_EVOSEL_7 0 +#endif +// </e> + +// <e> Channel 8 settings +// <id> dmac_channel_8_settings +#ifndef CONF_DMAC_CHANNEL_8_SETTINGS +#define CONF_DMAC_CHANNEL_8_SETTINGS 0 +#endif + +// <q> Channel Enable +// <i> Indicates whether channel 8 is enabled or not +// <id> dmac_enable_8 +#ifndef CONF_DMAC_ENABLE_8 +#define CONF_DMAC_ENABLE_8 0 +#endif + +// <q> Channel Run in Standby +// <i> Indicates whether channel 8 is running in standby mode or not +// <id> dmac_runstdby_8 +#ifndef CONF_DMAC_RUNSTDBY_8 +#define CONF_DMAC_RUNSTDBY_8 0 +#endif + +// <o> Trigger action +// <0=> One trigger required for each block transfer +// <2=> One trigger required for each beat transfer +// <3=> One trigger required for each transaction +// <i> Defines the trigger action used for a transfer +// <id> dmac_trigact_8 +#ifndef CONF_DMAC_TRIGACT_8 +#define CONF_DMAC_TRIGACT_8 0 +#endif + +// <o> Trigger source +// <0x00=> Only software/event triggers +// <0x01=> RTC Timestamp +// <0x02=> SERCOM0 RX Trigger +// <0x03=> SERCOM0 TX Trigger +// <0x04=> SERCOM1 RX Trigger +// <0x05=> SERCOM1 TX Trigger +// <0x06=> SERCOM2 RX Trigger +// <0x07=> SERCOM2 TX Trigger +// <0x08=> SERCOM3 RX Trigger +// <0x09=> SERCOM3 TX Trigger +// <0x0A=> SERCOM4 RX Trigger +// <0x0B=> SERCOM4 TX Trigger +// <0x0C=> SERCOM5 RX Trigger +// <0x0D=> SERCOM5 TX Trigger +// <0x0E=> TCC0 Overflow Trigger +// <0x0F=> TCC0 Match/Compare 0 Trigger +// <0x10=> TCC0 Match/Compare 1 Trigger +// <0x11=> TCC0 Match/Compare 2 Trigger +// <0x12=> TCC0 Match/Compare 3 Trigger +// <0x13=> TC0 Overflow Trigger +// <0x14=> TC0 Match/Compare 0 Trigger +// <0x15=> TC0 Match/Compare 1 Trigger +// <0x16=> TC1 Overflow Trigger +// <0x17=> TC1 Match/Compare 0 Trigger +// <0x18=> TC1 Match/Compare 1 Trigger +// <0x19=> TC2 Overflow Trigger +// <0x1A=> TC2 Match/Compare 0 Trigger +// <0x1B=> TC2 Match/Compare 1 Trigger +// <0x1C=> TC3 Overflow Trigger +// <0x1D=> TC3 Match/Compare 0 Trigger +// <0x1E=> TC3 Match/Compare 1 Trigger +// <0x1F=> ADC Result Ready Trigger +// <0x20=> SLCD Display Memory Update Trigger +// <0x21=> SLCD Automated Character Mapping Data Ready Trigger +// <0x22=> SLCD Automated Bit Mapping Data Ready Trigger +// <0x23=> AES Write Trigger +// <0x24=> AES Read Trigger +// <0x25=> PTC End of Conversion Trigger +// <0x26=> PTC Sequence Trigger +// <0x27=> PTC Window Comparator Trigger +// <i> Defines the peripheral trigger which is source of the transfer +// <id> dmac_trifsrc_8 +#ifndef CONF_DMAC_TRIGSRC_8 +#define CONF_DMAC_TRIGSRC_8 0 +#endif + +// <o> Channel Arbitration Level +// <0=> Channel priority 0 +// <1=> Channel priority 1 +// <2=> Channel priority 2 +// <3=> Channel priority 3 +// <i> Defines the arbitration level for this channel +// <id> dmac_lvl_8 +#ifndef CONF_DMAC_LVL_8 +#define CONF_DMAC_LVL_8 0 +#endif + +// <q> Channel Event Output +// <i> Indicates whether channel event generation is enabled or not +// <id> dmac_evoe_8 +#ifndef CONF_DMAC_EVOE_8 +#define CONF_DMAC_EVOE_8 0 +#endif + +// <q> Channel Event Input +// <i> Indicates whether channel event reception is enabled or not +// <id> dmac_evie_8 +#ifndef CONF_DMAC_EVIE_8 +#define CONF_DMAC_EVIE_8 0 +#endif + +// <o> Event Input Action +// <0=> No action +// <1=> Normal transfer and conditional transfer on strobe trigger +// <2=> Conditional transfer trigger +// <3=> Conditional block transfer +// <4=> Channel suspend operation +// <5=> Channel resume operation +// <6=> Skip next block suspend action +// <i> Defines the event input action +// <id> dmac_evact_8 +#ifndef CONF_DMAC_EVACT_8 +#define CONF_DMAC_EVACT_8 0 +#endif + +// <o> Address Increment Step Size +// <0=> Next ADDR = ADDR + (BEATSIZE + 1) * 1 +// <1=> Next ADDR = ADDR + (BEATSIZE + 1) * 2 +// <2=> Next ADDR = ADDR + (BEATSIZE + 1) * 4 +// <3=> Next ADDR = ADDR + (BEATSIZE + 1) * 8 +// <4=> Next ADDR = ADDR + (BEATSIZE + 1) * 16 +// <5=> Next ADDR = ADDR + (BEATSIZE + 1) * 32 +// <6=> Next ADDR = ADDR + (BEATSIZE + 1) * 64 +// <7=> Next ADDR = ADDR + (BEATSIZE + 1) * 128 +// <i> Defines the address increment step size, applies to source or destination address +// <id> dmac_stepsize_8 +#ifndef CONF_DMAC_STEPSIZE_8 +#define CONF_DMAC_STEPSIZE_8 0 +#endif + +// <o> Step Selection +// <0=> Step size settings apply to the destination address +// <1=> Step size settings apply to the source address +// <i> Defines whether source or destination addresses are using the step size settings +// <id> dmac_stepsel_8 +#ifndef CONF_DMAC_STEPSEL_8 +#define CONF_DMAC_STEPSEL_8 0 +#endif + +// <q> Source Address Increment +// <i> Indicates whether the source address incrementation is enabled or not +// <id> dmac_srcinc_8 +#ifndef CONF_DMAC_SRCINC_8 +#define CONF_DMAC_SRCINC_8 0 +#endif + +// <q> Destination Address Increment +// <i> Indicates whether the destination address incrementation is enabled or not +// <id> dmac_dstinc_8 +#ifndef CONF_DMAC_DSTINC_8 +#define CONF_DMAC_DSTINC_8 0 +#endif + +// <o> Beat Size +// <0=> 8-bit bus transfer +// <1=> 16-bit bus transfer +// <2=> 32-bit bus transfer +// <i> Defines the size of one beat +// <id> dmac_beatsize_8 +#ifndef CONF_DMAC_BEATSIZE_8 +#define CONF_DMAC_BEATSIZE_8 0 +#endif + +// <o> Block Action +// <0=> Channel will be disabled if it is the last block transfer in the transaction +// <1=> Channel will be disabled if it is the last block transfer in the transaction and block interrupt +// <2=> Channel suspend operation is complete +// <3=> Both channel suspend operation and block interrupt +// <i> Defines the the DMAC should take after a block transfer has completed +// <id> dmac_blockact_8 +#ifndef CONF_DMAC_BLOCKACT_8 +#define CONF_DMAC_BLOCKACT_8 0 +#endif + +// <o> Event Output Selection +// <0=> Event generation disabled +// <1=> Event strobe when block transfer complete +// <3=> Event strobe when beat transfer complete +// <i> Defines the event output selection +// <id> dmac_evosel_8 +#ifndef CONF_DMAC_EVOSEL_8 +#define CONF_DMAC_EVOSEL_8 0 +#endif +// </e> + +// <e> Channel 9 settings +// <id> dmac_channel_9_settings +#ifndef CONF_DMAC_CHANNEL_9_SETTINGS +#define CONF_DMAC_CHANNEL_9_SETTINGS 0 +#endif + +// <q> Channel Enable +// <i> Indicates whether channel 9 is enabled or not +// <id> dmac_enable_9 +#ifndef CONF_DMAC_ENABLE_9 +#define CONF_DMAC_ENABLE_9 0 +#endif + +// <q> Channel Run in Standby +// <i> Indicates whether channel 9 is running in standby mode or not +// <id> dmac_runstdby_9 +#ifndef CONF_DMAC_RUNSTDBY_9 +#define CONF_DMAC_RUNSTDBY_9 0 +#endif + +// <o> Trigger action +// <0=> One trigger required for each block transfer +// <2=> One trigger required for each beat transfer +// <3=> One trigger required for each transaction +// <i> Defines the trigger action used for a transfer +// <id> dmac_trigact_9 +#ifndef CONF_DMAC_TRIGACT_9 +#define CONF_DMAC_TRIGACT_9 0 +#endif + +// <o> Trigger source +// <0x00=> Only software/event triggers +// <0x01=> RTC Timestamp +// <0x02=> SERCOM0 RX Trigger +// <0x03=> SERCOM0 TX Trigger +// <0x04=> SERCOM1 RX Trigger +// <0x05=> SERCOM1 TX Trigger +// <0x06=> SERCOM2 RX Trigger +// <0x07=> SERCOM2 TX Trigger +// <0x08=> SERCOM3 RX Trigger +// <0x09=> SERCOM3 TX Trigger +// <0x0A=> SERCOM4 RX Trigger +// <0x0B=> SERCOM4 TX Trigger +// <0x0C=> SERCOM5 RX Trigger +// <0x0D=> SERCOM5 TX Trigger +// <0x0E=> TCC0 Overflow Trigger +// <0x0F=> TCC0 Match/Compare 0 Trigger +// <0x10=> TCC0 Match/Compare 1 Trigger +// <0x11=> TCC0 Match/Compare 2 Trigger +// <0x12=> TCC0 Match/Compare 3 Trigger +// <0x13=> TC0 Overflow Trigger +// <0x14=> TC0 Match/Compare 0 Trigger +// <0x15=> TC0 Match/Compare 1 Trigger +// <0x16=> TC1 Overflow Trigger +// <0x17=> TC1 Match/Compare 0 Trigger +// <0x18=> TC1 Match/Compare 1 Trigger +// <0x19=> TC2 Overflow Trigger +// <0x1A=> TC2 Match/Compare 0 Trigger +// <0x1B=> TC2 Match/Compare 1 Trigger +// <0x1C=> TC3 Overflow Trigger +// <0x1D=> TC3 Match/Compare 0 Trigger +// <0x1E=> TC3 Match/Compare 1 Trigger +// <0x1F=> ADC Result Ready Trigger +// <0x20=> SLCD Display Memory Update Trigger +// <0x21=> SLCD Automated Character Mapping Data Ready Trigger +// <0x22=> SLCD Automated Bit Mapping Data Ready Trigger +// <0x23=> AES Write Trigger +// <0x24=> AES Read Trigger +// <0x25=> PTC End of Conversion Trigger +// <0x26=> PTC Sequence Trigger +// <0x27=> PTC Window Comparator Trigger +// <i> Defines the peripheral trigger which is source of the transfer +// <id> dmac_trifsrc_9 +#ifndef CONF_DMAC_TRIGSRC_9 +#define CONF_DMAC_TRIGSRC_9 0 +#endif + +// <o> Channel Arbitration Level +// <0=> Channel priority 0 +// <1=> Channel priority 1 +// <2=> Channel priority 2 +// <3=> Channel priority 3 +// <i> Defines the arbitration level for this channel +// <id> dmac_lvl_9 +#ifndef CONF_DMAC_LVL_9 +#define CONF_DMAC_LVL_9 0 +#endif + +// <q> Channel Event Output +// <i> Indicates whether channel event generation is enabled or not +// <id> dmac_evoe_9 +#ifndef CONF_DMAC_EVOE_9 +#define CONF_DMAC_EVOE_9 0 +#endif + +// <q> Channel Event Input +// <i> Indicates whether channel event reception is enabled or not +// <id> dmac_evie_9 +#ifndef CONF_DMAC_EVIE_9 +#define CONF_DMAC_EVIE_9 0 +#endif + +// <o> Event Input Action +// <0=> No action +// <1=> Normal transfer and conditional transfer on strobe trigger +// <2=> Conditional transfer trigger +// <3=> Conditional block transfer +// <4=> Channel suspend operation +// <5=> Channel resume operation +// <6=> Skip next block suspend action +// <i> Defines the event input action +// <id> dmac_evact_9 +#ifndef CONF_DMAC_EVACT_9 +#define CONF_DMAC_EVACT_9 0 +#endif + +// <o> Address Increment Step Size +// <0=> Next ADDR = ADDR + (BEATSIZE + 1) * 1 +// <1=> Next ADDR = ADDR + (BEATSIZE + 1) * 2 +// <2=> Next ADDR = ADDR + (BEATSIZE + 1) * 4 +// <3=> Next ADDR = ADDR + (BEATSIZE + 1) * 8 +// <4=> Next ADDR = ADDR + (BEATSIZE + 1) * 16 +// <5=> Next ADDR = ADDR + (BEATSIZE + 1) * 32 +// <6=> Next ADDR = ADDR + (BEATSIZE + 1) * 64 +// <7=> Next ADDR = ADDR + (BEATSIZE + 1) * 128 +// <i> Defines the address increment step size, applies to source or destination address +// <id> dmac_stepsize_9 +#ifndef CONF_DMAC_STEPSIZE_9 +#define CONF_DMAC_STEPSIZE_9 0 +#endif + +// <o> Step Selection +// <0=> Step size settings apply to the destination address +// <1=> Step size settings apply to the source address +// <i> Defines whether source or destination addresses are using the step size settings +// <id> dmac_stepsel_9 +#ifndef CONF_DMAC_STEPSEL_9 +#define CONF_DMAC_STEPSEL_9 0 +#endif + +// <q> Source Address Increment +// <i> Indicates whether the source address incrementation is enabled or not +// <id> dmac_srcinc_9 +#ifndef CONF_DMAC_SRCINC_9 +#define CONF_DMAC_SRCINC_9 0 +#endif + +// <q> Destination Address Increment +// <i> Indicates whether the destination address incrementation is enabled or not +// <id> dmac_dstinc_9 +#ifndef CONF_DMAC_DSTINC_9 +#define CONF_DMAC_DSTINC_9 0 +#endif + +// <o> Beat Size +// <0=> 8-bit bus transfer +// <1=> 16-bit bus transfer +// <2=> 32-bit bus transfer +// <i> Defines the size of one beat +// <id> dmac_beatsize_9 +#ifndef CONF_DMAC_BEATSIZE_9 +#define CONF_DMAC_BEATSIZE_9 0 +#endif + +// <o> Block Action +// <0=> Channel will be disabled if it is the last block transfer in the transaction +// <1=> Channel will be disabled if it is the last block transfer in the transaction and block interrupt +// <2=> Channel suspend operation is complete +// <3=> Both channel suspend operation and block interrupt +// <i> Defines the the DMAC should take after a block transfer has completed +// <id> dmac_blockact_9 +#ifndef CONF_DMAC_BLOCKACT_9 +#define CONF_DMAC_BLOCKACT_9 0 +#endif + +// <o> Event Output Selection +// <0=> Event generation disabled +// <1=> Event strobe when block transfer complete +// <3=> Event strobe when beat transfer complete +// <i> Defines the event output selection +// <id> dmac_evosel_9 +#ifndef CONF_DMAC_EVOSEL_9 +#define CONF_DMAC_EVOSEL_9 0 +#endif +// </e> + +// <e> Channel 10 settings +// <id> dmac_channel_10_settings +#ifndef CONF_DMAC_CHANNEL_10_SETTINGS +#define CONF_DMAC_CHANNEL_10_SETTINGS 0 +#endif + +// <q> Channel Enable +// <i> Indicates whether channel 10 is enabled or not +// <id> dmac_enable_10 +#ifndef CONF_DMAC_ENABLE_10 +#define CONF_DMAC_ENABLE_10 0 +#endif + +// <q> Channel Run in Standby +// <i> Indicates whether channel 10 is running in standby mode or not +// <id> dmac_runstdby_10 +#ifndef CONF_DMAC_RUNSTDBY_10 +#define CONF_DMAC_RUNSTDBY_10 0 +#endif + +// <o> Trigger action +// <0=> One trigger required for each block transfer +// <2=> One trigger required for each beat transfer +// <3=> One trigger required for each transaction +// <i> Defines the trigger action used for a transfer +// <id> dmac_trigact_10 +#ifndef CONF_DMAC_TRIGACT_10 +#define CONF_DMAC_TRIGACT_10 0 +#endif + +// <o> Trigger source +// <0x00=> Only software/event triggers +// <0x01=> RTC Timestamp +// <0x02=> SERCOM0 RX Trigger +// <0x03=> SERCOM0 TX Trigger +// <0x04=> SERCOM1 RX Trigger +// <0x05=> SERCOM1 TX Trigger +// <0x06=> SERCOM2 RX Trigger +// <0x07=> SERCOM2 TX Trigger +// <0x08=> SERCOM3 RX Trigger +// <0x09=> SERCOM3 TX Trigger +// <0x0A=> SERCOM4 RX Trigger +// <0x0B=> SERCOM4 TX Trigger +// <0x0C=> SERCOM5 RX Trigger +// <0x0D=> SERCOM5 TX Trigger +// <0x0E=> TCC0 Overflow Trigger +// <0x0F=> TCC0 Match/Compare 0 Trigger +// <0x10=> TCC0 Match/Compare 1 Trigger +// <0x11=> TCC0 Match/Compare 2 Trigger +// <0x12=> TCC0 Match/Compare 3 Trigger +// <0x13=> TC0 Overflow Trigger +// <0x14=> TC0 Match/Compare 0 Trigger +// <0x15=> TC0 Match/Compare 1 Trigger +// <0x16=> TC1 Overflow Trigger +// <0x17=> TC1 Match/Compare 0 Trigger +// <0x18=> TC1 Match/Compare 1 Trigger +// <0x19=> TC2 Overflow Trigger +// <0x1A=> TC2 Match/Compare 0 Trigger +// <0x1B=> TC2 Match/Compare 1 Trigger +// <0x1C=> TC3 Overflow Trigger +// <0x1D=> TC3 Match/Compare 0 Trigger +// <0x1E=> TC3 Match/Compare 1 Trigger +// <0x1F=> ADC Result Ready Trigger +// <0x20=> SLCD Display Memory Update Trigger +// <0x21=> SLCD Automated Character Mapping Data Ready Trigger +// <0x22=> SLCD Automated Bit Mapping Data Ready Trigger +// <0x23=> AES Write Trigger +// <0x24=> AES Read Trigger +// <0x25=> PTC End of Conversion Trigger +// <0x26=> PTC Sequence Trigger +// <0x27=> PTC Window Comparator Trigger +// <i> Defines the peripheral trigger which is source of the transfer +// <id> dmac_trifsrc_10 +#ifndef CONF_DMAC_TRIGSRC_10 +#define CONF_DMAC_TRIGSRC_10 0 +#endif + +// <o> Channel Arbitration Level +// <0=> Channel priority 0 +// <1=> Channel priority 1 +// <2=> Channel priority 2 +// <3=> Channel priority 3 +// <i> Defines the arbitration level for this channel +// <id> dmac_lvl_10 +#ifndef CONF_DMAC_LVL_10 +#define CONF_DMAC_LVL_10 0 +#endif + +// <q> Channel Event Output +// <i> Indicates whether channel event generation is enabled or not +// <id> dmac_evoe_10 +#ifndef CONF_DMAC_EVOE_10 +#define CONF_DMAC_EVOE_10 0 +#endif + +// <q> Channel Event Input +// <i> Indicates whether channel event reception is enabled or not +// <id> dmac_evie_10 +#ifndef CONF_DMAC_EVIE_10 +#define CONF_DMAC_EVIE_10 0 +#endif + +// <o> Event Input Action +// <0=> No action +// <1=> Normal transfer and conditional transfer on strobe trigger +// <2=> Conditional transfer trigger +// <3=> Conditional block transfer +// <4=> Channel suspend operation +// <5=> Channel resume operation +// <6=> Skip next block suspend action +// <i> Defines the event input action +// <id> dmac_evact_10 +#ifndef CONF_DMAC_EVACT_10 +#define CONF_DMAC_EVACT_10 0 +#endif + +// <o> Address Increment Step Size +// <0=> Next ADDR = ADDR + (BEATSIZE + 1) * 1 +// <1=> Next ADDR = ADDR + (BEATSIZE + 1) * 2 +// <2=> Next ADDR = ADDR + (BEATSIZE + 1) * 4 +// <3=> Next ADDR = ADDR + (BEATSIZE + 1) * 8 +// <4=> Next ADDR = ADDR + (BEATSIZE + 1) * 16 +// <5=> Next ADDR = ADDR + (BEATSIZE + 1) * 32 +// <6=> Next ADDR = ADDR + (BEATSIZE + 1) * 64 +// <7=> Next ADDR = ADDR + (BEATSIZE + 1) * 128 +// <i> Defines the address increment step size, applies to source or destination address +// <id> dmac_stepsize_10 +#ifndef CONF_DMAC_STEPSIZE_10 +#define CONF_DMAC_STEPSIZE_10 0 +#endif + +// <o> Step Selection +// <0=> Step size settings apply to the destination address +// <1=> Step size settings apply to the source address +// <i> Defines whether source or destination addresses are using the step size settings +// <id> dmac_stepsel_10 +#ifndef CONF_DMAC_STEPSEL_10 +#define CONF_DMAC_STEPSEL_10 0 +#endif + +// <q> Source Address Increment +// <i> Indicates whether the source address incrementation is enabled or not +// <id> dmac_srcinc_10 +#ifndef CONF_DMAC_SRCINC_10 +#define CONF_DMAC_SRCINC_10 0 +#endif + +// <q> Destination Address Increment +// <i> Indicates whether the destination address incrementation is enabled or not +// <id> dmac_dstinc_10 +#ifndef CONF_DMAC_DSTINC_10 +#define CONF_DMAC_DSTINC_10 0 +#endif + +// <o> Beat Size +// <0=> 8-bit bus transfer +// <1=> 16-bit bus transfer +// <2=> 32-bit bus transfer +// <i> Defines the size of one beat +// <id> dmac_beatsize_10 +#ifndef CONF_DMAC_BEATSIZE_10 +#define CONF_DMAC_BEATSIZE_10 0 +#endif + +// <o> Block Action +// <0=> Channel will be disabled if it is the last block transfer in the transaction +// <1=> Channel will be disabled if it is the last block transfer in the transaction and block interrupt +// <2=> Channel suspend operation is complete +// <3=> Both channel suspend operation and block interrupt +// <i> Defines the the DMAC should take after a block transfer has completed +// <id> dmac_blockact_10 +#ifndef CONF_DMAC_BLOCKACT_10 +#define CONF_DMAC_BLOCKACT_10 0 +#endif + +// <o> Event Output Selection +// <0=> Event generation disabled +// <1=> Event strobe when block transfer complete +// <3=> Event strobe when beat transfer complete +// <i> Defines the event output selection +// <id> dmac_evosel_10 +#ifndef CONF_DMAC_EVOSEL_10 +#define CONF_DMAC_EVOSEL_10 0 +#endif +// </e> + +// <e> Channel 11 settings +// <id> dmac_channel_11_settings +#ifndef CONF_DMAC_CHANNEL_11_SETTINGS +#define CONF_DMAC_CHANNEL_11_SETTINGS 0 +#endif + +// <q> Channel Enable +// <i> Indicates whether channel 11 is enabled or not +// <id> dmac_enable_11 +#ifndef CONF_DMAC_ENABLE_11 +#define CONF_DMAC_ENABLE_11 0 +#endif + +// <q> Channel Run in Standby +// <i> Indicates whether channel 11 is running in standby mode or not +// <id> dmac_runstdby_11 +#ifndef CONF_DMAC_RUNSTDBY_11 +#define CONF_DMAC_RUNSTDBY_11 0 +#endif + +// <o> Trigger action +// <0=> One trigger required for each block transfer +// <2=> One trigger required for each beat transfer +// <3=> One trigger required for each transaction +// <i> Defines the trigger action used for a transfer +// <id> dmac_trigact_11 +#ifndef CONF_DMAC_TRIGACT_11 +#define CONF_DMAC_TRIGACT_11 0 +#endif + +// <o> Trigger source +// <0x00=> Only software/event triggers +// <0x01=> RTC Timestamp +// <0x02=> SERCOM0 RX Trigger +// <0x03=> SERCOM0 TX Trigger +// <0x04=> SERCOM1 RX Trigger +// <0x05=> SERCOM1 TX Trigger +// <0x06=> SERCOM2 RX Trigger +// <0x07=> SERCOM2 TX Trigger +// <0x08=> SERCOM3 RX Trigger +// <0x09=> SERCOM3 TX Trigger +// <0x0A=> SERCOM4 RX Trigger +// <0x0B=> SERCOM4 TX Trigger +// <0x0C=> SERCOM5 RX Trigger +// <0x0D=> SERCOM5 TX Trigger +// <0x0E=> TCC0 Overflow Trigger +// <0x0F=> TCC0 Match/Compare 0 Trigger +// <0x10=> TCC0 Match/Compare 1 Trigger +// <0x11=> TCC0 Match/Compare 2 Trigger +// <0x12=> TCC0 Match/Compare 3 Trigger +// <0x13=> TC0 Overflow Trigger +// <0x14=> TC0 Match/Compare 0 Trigger +// <0x15=> TC0 Match/Compare 1 Trigger +// <0x16=> TC1 Overflow Trigger +// <0x17=> TC1 Match/Compare 0 Trigger +// <0x18=> TC1 Match/Compare 1 Trigger +// <0x19=> TC2 Overflow Trigger +// <0x1A=> TC2 Match/Compare 0 Trigger +// <0x1B=> TC2 Match/Compare 1 Trigger +// <0x1C=> TC3 Overflow Trigger +// <0x1D=> TC3 Match/Compare 0 Trigger +// <0x1E=> TC3 Match/Compare 1 Trigger +// <0x1F=> ADC Result Ready Trigger +// <0x20=> SLCD Display Memory Update Trigger +// <0x21=> SLCD Automated Character Mapping Data Ready Trigger +// <0x22=> SLCD Automated Bit Mapping Data Ready Trigger +// <0x23=> AES Write Trigger +// <0x24=> AES Read Trigger +// <0x25=> PTC End of Conversion Trigger +// <0x26=> PTC Sequence Trigger +// <0x27=> PTC Window Comparator Trigger +// <i> Defines the peripheral trigger which is source of the transfer +// <id> dmac_trifsrc_11 +#ifndef CONF_DMAC_TRIGSRC_11 +#define CONF_DMAC_TRIGSRC_11 0 +#endif + +// <o> Channel Arbitration Level +// <0=> Channel priority 0 +// <1=> Channel priority 1 +// <2=> Channel priority 2 +// <3=> Channel priority 3 +// <i> Defines the arbitration level for this channel +// <id> dmac_lvl_11 +#ifndef CONF_DMAC_LVL_11 +#define CONF_DMAC_LVL_11 0 +#endif + +// <q> Channel Event Output +// <i> Indicates whether channel event generation is enabled or not +// <id> dmac_evoe_11 +#ifndef CONF_DMAC_EVOE_11 +#define CONF_DMAC_EVOE_11 0 +#endif + +// <q> Channel Event Input +// <i> Indicates whether channel event reception is enabled or not +// <id> dmac_evie_11 +#ifndef CONF_DMAC_EVIE_11 +#define CONF_DMAC_EVIE_11 0 +#endif + +// <o> Event Input Action +// <0=> No action +// <1=> Normal transfer and conditional transfer on strobe trigger +// <2=> Conditional transfer trigger +// <3=> Conditional block transfer +// <4=> Channel suspend operation +// <5=> Channel resume operation +// <6=> Skip next block suspend action +// <i> Defines the event input action +// <id> dmac_evact_11 +#ifndef CONF_DMAC_EVACT_11 +#define CONF_DMAC_EVACT_11 0 +#endif + +// <o> Address Increment Step Size +// <0=> Next ADDR = ADDR + (BEATSIZE + 1) * 1 +// <1=> Next ADDR = ADDR + (BEATSIZE + 1) * 2 +// <2=> Next ADDR = ADDR + (BEATSIZE + 1) * 4 +// <3=> Next ADDR = ADDR + (BEATSIZE + 1) * 8 +// <4=> Next ADDR = ADDR + (BEATSIZE + 1) * 16 +// <5=> Next ADDR = ADDR + (BEATSIZE + 1) * 32 +// <6=> Next ADDR = ADDR + (BEATSIZE + 1) * 64 +// <7=> Next ADDR = ADDR + (BEATSIZE + 1) * 128 +// <i> Defines the address increment step size, applies to source or destination address +// <id> dmac_stepsize_11 +#ifndef CONF_DMAC_STEPSIZE_11 +#define CONF_DMAC_STEPSIZE_11 0 +#endif + +// <o> Step Selection +// <0=> Step size settings apply to the destination address +// <1=> Step size settings apply to the source address +// <i> Defines whether source or destination addresses are using the step size settings +// <id> dmac_stepsel_11 +#ifndef CONF_DMAC_STEPSEL_11 +#define CONF_DMAC_STEPSEL_11 0 +#endif + +// <q> Source Address Increment +// <i> Indicates whether the source address incrementation is enabled or not +// <id> dmac_srcinc_11 +#ifndef CONF_DMAC_SRCINC_11 +#define CONF_DMAC_SRCINC_11 0 +#endif + +// <q> Destination Address Increment +// <i> Indicates whether the destination address incrementation is enabled or not +// <id> dmac_dstinc_11 +#ifndef CONF_DMAC_DSTINC_11 +#define CONF_DMAC_DSTINC_11 0 +#endif + +// <o> Beat Size +// <0=> 8-bit bus transfer +// <1=> 16-bit bus transfer +// <2=> 32-bit bus transfer +// <i> Defines the size of one beat +// <id> dmac_beatsize_11 +#ifndef CONF_DMAC_BEATSIZE_11 +#define CONF_DMAC_BEATSIZE_11 0 +#endif + +// <o> Block Action +// <0=> Channel will be disabled if it is the last block transfer in the transaction +// <1=> Channel will be disabled if it is the last block transfer in the transaction and block interrupt +// <2=> Channel suspend operation is complete +// <3=> Both channel suspend operation and block interrupt +// <i> Defines the the DMAC should take after a block transfer has completed +// <id> dmac_blockact_11 +#ifndef CONF_DMAC_BLOCKACT_11 +#define CONF_DMAC_BLOCKACT_11 0 +#endif + +// <o> Event Output Selection +// <0=> Event generation disabled +// <1=> Event strobe when block transfer complete +// <3=> Event strobe when beat transfer complete +// <i> Defines the event output selection +// <id> dmac_evosel_11 +#ifndef CONF_DMAC_EVOSEL_11 +#define CONF_DMAC_EVOSEL_11 0 +#endif +// </e> + +// <e> Channel 12 settings +// <id> dmac_channel_12_settings +#ifndef CONF_DMAC_CHANNEL_12_SETTINGS +#define CONF_DMAC_CHANNEL_12_SETTINGS 0 +#endif + +// <q> Channel Enable +// <i> Indicates whether channel 12 is enabled or not +// <id> dmac_enable_12 +#ifndef CONF_DMAC_ENABLE_12 +#define CONF_DMAC_ENABLE_12 0 +#endif + +// <q> Channel Run in Standby +// <i> Indicates whether channel 12 is running in standby mode or not +// <id> dmac_runstdby_12 +#ifndef CONF_DMAC_RUNSTDBY_12 +#define CONF_DMAC_RUNSTDBY_12 0 +#endif + +// <o> Trigger action +// <0=> One trigger required for each block transfer +// <2=> One trigger required for each beat transfer +// <3=> One trigger required for each transaction +// <i> Defines the trigger action used for a transfer +// <id> dmac_trigact_12 +#ifndef CONF_DMAC_TRIGACT_12 +#define CONF_DMAC_TRIGACT_12 0 +#endif + +// <o> Trigger source +// <0x00=> Only software/event triggers +// <0x01=> RTC Timestamp +// <0x02=> SERCOM0 RX Trigger +// <0x03=> SERCOM0 TX Trigger +// <0x04=> SERCOM1 RX Trigger +// <0x05=> SERCOM1 TX Trigger +// <0x06=> SERCOM2 RX Trigger +// <0x07=> SERCOM2 TX Trigger +// <0x08=> SERCOM3 RX Trigger +// <0x09=> SERCOM3 TX Trigger +// <0x0A=> SERCOM4 RX Trigger +// <0x0B=> SERCOM4 TX Trigger +// <0x0C=> SERCOM5 RX Trigger +// <0x0D=> SERCOM5 TX Trigger +// <0x0E=> TCC0 Overflow Trigger +// <0x0F=> TCC0 Match/Compare 0 Trigger +// <0x10=> TCC0 Match/Compare 1 Trigger +// <0x11=> TCC0 Match/Compare 2 Trigger +// <0x12=> TCC0 Match/Compare 3 Trigger +// <0x13=> TC0 Overflow Trigger +// <0x14=> TC0 Match/Compare 0 Trigger +// <0x15=> TC0 Match/Compare 1 Trigger +// <0x16=> TC1 Overflow Trigger +// <0x17=> TC1 Match/Compare 0 Trigger +// <0x18=> TC1 Match/Compare 1 Trigger +// <0x19=> TC2 Overflow Trigger +// <0x1A=> TC2 Match/Compare 0 Trigger +// <0x1B=> TC2 Match/Compare 1 Trigger +// <0x1C=> TC3 Overflow Trigger +// <0x1D=> TC3 Match/Compare 0 Trigger +// <0x1E=> TC3 Match/Compare 1 Trigger +// <0x1F=> ADC Result Ready Trigger +// <0x20=> SLCD Display Memory Update Trigger +// <0x21=> SLCD Automated Character Mapping Data Ready Trigger +// <0x22=> SLCD Automated Bit Mapping Data Ready Trigger +// <0x23=> AES Write Trigger +// <0x24=> AES Read Trigger +// <0x25=> PTC End of Conversion Trigger +// <0x26=> PTC Sequence Trigger +// <0x27=> PTC Window Comparator Trigger +// <i> Defines the peripheral trigger which is source of the transfer +// <id> dmac_trifsrc_12 +#ifndef CONF_DMAC_TRIGSRC_12 +#define CONF_DMAC_TRIGSRC_12 0 +#endif + +// <o> Channel Arbitration Level +// <0=> Channel priority 0 +// <1=> Channel priority 1 +// <2=> Channel priority 2 +// <3=> Channel priority 3 +// <i> Defines the arbitration level for this channel +// <id> dmac_lvl_12 +#ifndef CONF_DMAC_LVL_12 +#define CONF_DMAC_LVL_12 0 +#endif + +// <q> Channel Event Output +// <i> Indicates whether channel event generation is enabled or not +// <id> dmac_evoe_12 +#ifndef CONF_DMAC_EVOE_12 +#define CONF_DMAC_EVOE_12 0 +#endif + +// <q> Channel Event Input +// <i> Indicates whether channel event reception is enabled or not +// <id> dmac_evie_12 +#ifndef CONF_DMAC_EVIE_12 +#define CONF_DMAC_EVIE_12 0 +#endif + +// <o> Event Input Action +// <0=> No action +// <1=> Normal transfer and conditional transfer on strobe trigger +// <2=> Conditional transfer trigger +// <3=> Conditional block transfer +// <4=> Channel suspend operation +// <5=> Channel resume operation +// <6=> Skip next block suspend action +// <i> Defines the event input action +// <id> dmac_evact_12 +#ifndef CONF_DMAC_EVACT_12 +#define CONF_DMAC_EVACT_12 0 +#endif + +// <o> Address Increment Step Size +// <0=> Next ADDR = ADDR + (BEATSIZE + 1) * 1 +// <1=> Next ADDR = ADDR + (BEATSIZE + 1) * 2 +// <2=> Next ADDR = ADDR + (BEATSIZE + 1) * 4 +// <3=> Next ADDR = ADDR + (BEATSIZE + 1) * 8 +// <4=> Next ADDR = ADDR + (BEATSIZE + 1) * 16 +// <5=> Next ADDR = ADDR + (BEATSIZE + 1) * 32 +// <6=> Next ADDR = ADDR + (BEATSIZE + 1) * 64 +// <7=> Next ADDR = ADDR + (BEATSIZE + 1) * 128 +// <i> Defines the address increment step size, applies to source or destination address +// <id> dmac_stepsize_12 +#ifndef CONF_DMAC_STEPSIZE_12 +#define CONF_DMAC_STEPSIZE_12 0 +#endif + +// <o> Step Selection +// <0=> Step size settings apply to the destination address +// <1=> Step size settings apply to the source address +// <i> Defines whether source or destination addresses are using the step size settings +// <id> dmac_stepsel_12 +#ifndef CONF_DMAC_STEPSEL_12 +#define CONF_DMAC_STEPSEL_12 0 +#endif + +// <q> Source Address Increment +// <i> Indicates whether the source address incrementation is enabled or not +// <id> dmac_srcinc_12 +#ifndef CONF_DMAC_SRCINC_12 +#define CONF_DMAC_SRCINC_12 0 +#endif + +// <q> Destination Address Increment +// <i> Indicates whether the destination address incrementation is enabled or not +// <id> dmac_dstinc_12 +#ifndef CONF_DMAC_DSTINC_12 +#define CONF_DMAC_DSTINC_12 0 +#endif + +// <o> Beat Size +// <0=> 8-bit bus transfer +// <1=> 16-bit bus transfer +// <2=> 32-bit bus transfer +// <i> Defines the size of one beat +// <id> dmac_beatsize_12 +#ifndef CONF_DMAC_BEATSIZE_12 +#define CONF_DMAC_BEATSIZE_12 0 +#endif + +// <o> Block Action +// <0=> Channel will be disabled if it is the last block transfer in the transaction +// <1=> Channel will be disabled if it is the last block transfer in the transaction and block interrupt +// <2=> Channel suspend operation is complete +// <3=> Both channel suspend operation and block interrupt +// <i> Defines the the DMAC should take after a block transfer has completed +// <id> dmac_blockact_12 +#ifndef CONF_DMAC_BLOCKACT_12 +#define CONF_DMAC_BLOCKACT_12 0 +#endif + +// <o> Event Output Selection +// <0=> Event generation disabled +// <1=> Event strobe when block transfer complete +// <3=> Event strobe when beat transfer complete +// <i> Defines the event output selection +// <id> dmac_evosel_12 +#ifndef CONF_DMAC_EVOSEL_12 +#define CONF_DMAC_EVOSEL_12 0 +#endif +// </e> + +// <e> Channel 13 settings +// <id> dmac_channel_13_settings +#ifndef CONF_DMAC_CHANNEL_13_SETTINGS +#define CONF_DMAC_CHANNEL_13_SETTINGS 0 +#endif + +// <q> Channel Enable +// <i> Indicates whether channel 13 is enabled or not +// <id> dmac_enable_13 +#ifndef CONF_DMAC_ENABLE_13 +#define CONF_DMAC_ENABLE_13 0 +#endif + +// <q> Channel Run in Standby +// <i> Indicates whether channel 13 is running in standby mode or not +// <id> dmac_runstdby_13 +#ifndef CONF_DMAC_RUNSTDBY_13 +#define CONF_DMAC_RUNSTDBY_13 0 +#endif + +// <o> Trigger action +// <0=> One trigger required for each block transfer +// <2=> One trigger required for each beat transfer +// <3=> One trigger required for each transaction +// <i> Defines the trigger action used for a transfer +// <id> dmac_trigact_13 +#ifndef CONF_DMAC_TRIGACT_13 +#define CONF_DMAC_TRIGACT_13 0 +#endif + +// <o> Trigger source +// <0x00=> Only software/event triggers +// <0x01=> RTC Timestamp +// <0x02=> SERCOM0 RX Trigger +// <0x03=> SERCOM0 TX Trigger +// <0x04=> SERCOM1 RX Trigger +// <0x05=> SERCOM1 TX Trigger +// <0x06=> SERCOM2 RX Trigger +// <0x07=> SERCOM2 TX Trigger +// <0x08=> SERCOM3 RX Trigger +// <0x09=> SERCOM3 TX Trigger +// <0x0A=> SERCOM4 RX Trigger +// <0x0B=> SERCOM4 TX Trigger +// <0x0C=> SERCOM5 RX Trigger +// <0x0D=> SERCOM5 TX Trigger +// <0x0E=> TCC0 Overflow Trigger +// <0x0F=> TCC0 Match/Compare 0 Trigger +// <0x10=> TCC0 Match/Compare 1 Trigger +// <0x11=> TCC0 Match/Compare 2 Trigger +// <0x12=> TCC0 Match/Compare 3 Trigger +// <0x13=> TC0 Overflow Trigger +// <0x14=> TC0 Match/Compare 0 Trigger +// <0x15=> TC0 Match/Compare 1 Trigger +// <0x16=> TC1 Overflow Trigger +// <0x17=> TC1 Match/Compare 0 Trigger +// <0x18=> TC1 Match/Compare 1 Trigger +// <0x19=> TC2 Overflow Trigger +// <0x1A=> TC2 Match/Compare 0 Trigger +// <0x1B=> TC2 Match/Compare 1 Trigger +// <0x1C=> TC3 Overflow Trigger +// <0x1D=> TC3 Match/Compare 0 Trigger +// <0x1E=> TC3 Match/Compare 1 Trigger +// <0x1F=> ADC Result Ready Trigger +// <0x20=> SLCD Display Memory Update Trigger +// <0x21=> SLCD Automated Character Mapping Data Ready Trigger +// <0x22=> SLCD Automated Bit Mapping Data Ready Trigger +// <0x23=> AES Write Trigger +// <0x24=> AES Read Trigger +// <0x25=> PTC End of Conversion Trigger +// <0x26=> PTC Sequence Trigger +// <0x27=> PTC Window Comparator Trigger +// <i> Defines the peripheral trigger which is source of the transfer +// <id> dmac_trifsrc_13 +#ifndef CONF_DMAC_TRIGSRC_13 +#define CONF_DMAC_TRIGSRC_13 0 +#endif + +// <o> Channel Arbitration Level +// <0=> Channel priority 0 +// <1=> Channel priority 1 +// <2=> Channel priority 2 +// <3=> Channel priority 3 +// <i> Defines the arbitration level for this channel +// <id> dmac_lvl_13 +#ifndef CONF_DMAC_LVL_13 +#define CONF_DMAC_LVL_13 0 +#endif + +// <q> Channel Event Output +// <i> Indicates whether channel event generation is enabled or not +// <id> dmac_evoe_13 +#ifndef CONF_DMAC_EVOE_13 +#define CONF_DMAC_EVOE_13 0 +#endif + +// <q> Channel Event Input +// <i> Indicates whether channel event reception is enabled or not +// <id> dmac_evie_13 +#ifndef CONF_DMAC_EVIE_13 +#define CONF_DMAC_EVIE_13 0 +#endif + +// <o> Event Input Action +// <0=> No action +// <1=> Normal transfer and conditional transfer on strobe trigger +// <2=> Conditional transfer trigger +// <3=> Conditional block transfer +// <4=> Channel suspend operation +// <5=> Channel resume operation +// <6=> Skip next block suspend action +// <i> Defines the event input action +// <id> dmac_evact_13 +#ifndef CONF_DMAC_EVACT_13 +#define CONF_DMAC_EVACT_13 0 +#endif + +// <o> Address Increment Step Size +// <0=> Next ADDR = ADDR + (BEATSIZE + 1) * 1 +// <1=> Next ADDR = ADDR + (BEATSIZE + 1) * 2 +// <2=> Next ADDR = ADDR + (BEATSIZE + 1) * 4 +// <3=> Next ADDR = ADDR + (BEATSIZE + 1) * 8 +// <4=> Next ADDR = ADDR + (BEATSIZE + 1) * 16 +// <5=> Next ADDR = ADDR + (BEATSIZE + 1) * 32 +// <6=> Next ADDR = ADDR + (BEATSIZE + 1) * 64 +// <7=> Next ADDR = ADDR + (BEATSIZE + 1) * 128 +// <i> Defines the address increment step size, applies to source or destination address +// <id> dmac_stepsize_13 +#ifndef CONF_DMAC_STEPSIZE_13 +#define CONF_DMAC_STEPSIZE_13 0 +#endif + +// <o> Step Selection +// <0=> Step size settings apply to the destination address +// <1=> Step size settings apply to the source address +// <i> Defines whether source or destination addresses are using the step size settings +// <id> dmac_stepsel_13 +#ifndef CONF_DMAC_STEPSEL_13 +#define CONF_DMAC_STEPSEL_13 0 +#endif + +// <q> Source Address Increment +// <i> Indicates whether the source address incrementation is enabled or not +// <id> dmac_srcinc_13 +#ifndef CONF_DMAC_SRCINC_13 +#define CONF_DMAC_SRCINC_13 0 +#endif + +// <q> Destination Address Increment +// <i> Indicates whether the destination address incrementation is enabled or not +// <id> dmac_dstinc_13 +#ifndef CONF_DMAC_DSTINC_13 +#define CONF_DMAC_DSTINC_13 0 +#endif + +// <o> Beat Size +// <0=> 8-bit bus transfer +// <1=> 16-bit bus transfer +// <2=> 32-bit bus transfer +// <i> Defines the size of one beat +// <id> dmac_beatsize_13 +#ifndef CONF_DMAC_BEATSIZE_13 +#define CONF_DMAC_BEATSIZE_13 0 +#endif + +// <o> Block Action +// <0=> Channel will be disabled if it is the last block transfer in the transaction +// <1=> Channel will be disabled if it is the last block transfer in the transaction and block interrupt +// <2=> Channel suspend operation is complete +// <3=> Both channel suspend operation and block interrupt +// <i> Defines the the DMAC should take after a block transfer has completed +// <id> dmac_blockact_13 +#ifndef CONF_DMAC_BLOCKACT_13 +#define CONF_DMAC_BLOCKACT_13 0 +#endif + +// <o> Event Output Selection +// <0=> Event generation disabled +// <1=> Event strobe when block transfer complete +// <3=> Event strobe when beat transfer complete +// <i> Defines the event output selection +// <id> dmac_evosel_13 +#ifndef CONF_DMAC_EVOSEL_13 +#define CONF_DMAC_EVOSEL_13 0 +#endif +// </e> + +// <e> Channel 14 settings +// <id> dmac_channel_14_settings +#ifndef CONF_DMAC_CHANNEL_14_SETTINGS +#define CONF_DMAC_CHANNEL_14_SETTINGS 0 +#endif + +// <q> Channel Enable +// <i> Indicates whether channel 14 is enabled or not +// <id> dmac_enable_14 +#ifndef CONF_DMAC_ENABLE_14 +#define CONF_DMAC_ENABLE_14 0 +#endif + +// <q> Channel Run in Standby +// <i> Indicates whether channel 14 is running in standby mode or not +// <id> dmac_runstdby_14 +#ifndef CONF_DMAC_RUNSTDBY_14 +#define CONF_DMAC_RUNSTDBY_14 0 +#endif + +// <o> Trigger action +// <0=> One trigger required for each block transfer +// <2=> One trigger required for each beat transfer +// <3=> One trigger required for each transaction +// <i> Defines the trigger action used for a transfer +// <id> dmac_trigact_14 +#ifndef CONF_DMAC_TRIGACT_14 +#define CONF_DMAC_TRIGACT_14 0 +#endif + +// <o> Trigger source +// <0x00=> Only software/event triggers +// <0x01=> RTC Timestamp +// <0x02=> SERCOM0 RX Trigger +// <0x03=> SERCOM0 TX Trigger +// <0x04=> SERCOM1 RX Trigger +// <0x05=> SERCOM1 TX Trigger +// <0x06=> SERCOM2 RX Trigger +// <0x07=> SERCOM2 TX Trigger +// <0x08=> SERCOM3 RX Trigger +// <0x09=> SERCOM3 TX Trigger +// <0x0A=> SERCOM4 RX Trigger +// <0x0B=> SERCOM4 TX Trigger +// <0x0C=> SERCOM5 RX Trigger +// <0x0D=> SERCOM5 TX Trigger +// <0x0E=> TCC0 Overflow Trigger +// <0x0F=> TCC0 Match/Compare 0 Trigger +// <0x10=> TCC0 Match/Compare 1 Trigger +// <0x11=> TCC0 Match/Compare 2 Trigger +// <0x12=> TCC0 Match/Compare 3 Trigger +// <0x13=> TC0 Overflow Trigger +// <0x14=> TC0 Match/Compare 0 Trigger +// <0x15=> TC0 Match/Compare 1 Trigger +// <0x16=> TC1 Overflow Trigger +// <0x17=> TC1 Match/Compare 0 Trigger +// <0x18=> TC1 Match/Compare 1 Trigger +// <0x19=> TC2 Overflow Trigger +// <0x1A=> TC2 Match/Compare 0 Trigger +// <0x1B=> TC2 Match/Compare 1 Trigger +// <0x1C=> TC3 Overflow Trigger +// <0x1D=> TC3 Match/Compare 0 Trigger +// <0x1E=> TC3 Match/Compare 1 Trigger +// <0x1F=> ADC Result Ready Trigger +// <0x20=> SLCD Display Memory Update Trigger +// <0x21=> SLCD Automated Character Mapping Data Ready Trigger +// <0x22=> SLCD Automated Bit Mapping Data Ready Trigger +// <0x23=> AES Write Trigger +// <0x24=> AES Read Trigger +// <0x25=> PTC End of Conversion Trigger +// <0x26=> PTC Sequence Trigger +// <0x27=> PTC Window Comparator Trigger +// <i> Defines the peripheral trigger which is source of the transfer +// <id> dmac_trifsrc_14 +#ifndef CONF_DMAC_TRIGSRC_14 +#define CONF_DMAC_TRIGSRC_14 0 +#endif + +// <o> Channel Arbitration Level +// <0=> Channel priority 0 +// <1=> Channel priority 1 +// <2=> Channel priority 2 +// <3=> Channel priority 3 +// <i> Defines the arbitration level for this channel +// <id> dmac_lvl_14 +#ifndef CONF_DMAC_LVL_14 +#define CONF_DMAC_LVL_14 0 +#endif + +// <q> Channel Event Output +// <i> Indicates whether channel event generation is enabled or not +// <id> dmac_evoe_14 +#ifndef CONF_DMAC_EVOE_14 +#define CONF_DMAC_EVOE_14 0 +#endif + +// <q> Channel Event Input +// <i> Indicates whether channel event reception is enabled or not +// <id> dmac_evie_14 +#ifndef CONF_DMAC_EVIE_14 +#define CONF_DMAC_EVIE_14 0 +#endif + +// <o> Event Input Action +// <0=> No action +// <1=> Normal transfer and conditional transfer on strobe trigger +// <2=> Conditional transfer trigger +// <3=> Conditional block transfer +// <4=> Channel suspend operation +// <5=> Channel resume operation +// <6=> Skip next block suspend action +// <i> Defines the event input action +// <id> dmac_evact_14 +#ifndef CONF_DMAC_EVACT_14 +#define CONF_DMAC_EVACT_14 0 +#endif + +// <o> Address Increment Step Size +// <0=> Next ADDR = ADDR + (BEATSIZE + 1) * 1 +// <1=> Next ADDR = ADDR + (BEATSIZE + 1) * 2 +// <2=> Next ADDR = ADDR + (BEATSIZE + 1) * 4 +// <3=> Next ADDR = ADDR + (BEATSIZE + 1) * 8 +// <4=> Next ADDR = ADDR + (BEATSIZE + 1) * 16 +// <5=> Next ADDR = ADDR + (BEATSIZE + 1) * 32 +// <6=> Next ADDR = ADDR + (BEATSIZE + 1) * 64 +// <7=> Next ADDR = ADDR + (BEATSIZE + 1) * 128 +// <i> Defines the address increment step size, applies to source or destination address +// <id> dmac_stepsize_14 +#ifndef CONF_DMAC_STEPSIZE_14 +#define CONF_DMAC_STEPSIZE_14 0 +#endif + +// <o> Step Selection +// <0=> Step size settings apply to the destination address +// <1=> Step size settings apply to the source address +// <i> Defines whether source or destination addresses are using the step size settings +// <id> dmac_stepsel_14 +#ifndef CONF_DMAC_STEPSEL_14 +#define CONF_DMAC_STEPSEL_14 0 +#endif + +// <q> Source Address Increment +// <i> Indicates whether the source address incrementation is enabled or not +// <id> dmac_srcinc_14 +#ifndef CONF_DMAC_SRCINC_14 +#define CONF_DMAC_SRCINC_14 0 +#endif + +// <q> Destination Address Increment +// <i> Indicates whether the destination address incrementation is enabled or not +// <id> dmac_dstinc_14 +#ifndef CONF_DMAC_DSTINC_14 +#define CONF_DMAC_DSTINC_14 0 +#endif + +// <o> Beat Size +// <0=> 8-bit bus transfer +// <1=> 16-bit bus transfer +// <2=> 32-bit bus transfer +// <i> Defines the size of one beat +// <id> dmac_beatsize_14 +#ifndef CONF_DMAC_BEATSIZE_14 +#define CONF_DMAC_BEATSIZE_14 0 +#endif + +// <o> Block Action +// <0=> Channel will be disabled if it is the last block transfer in the transaction +// <1=> Channel will be disabled if it is the last block transfer in the transaction and block interrupt +// <2=> Channel suspend operation is complete +// <3=> Both channel suspend operation and block interrupt +// <i> Defines the the DMAC should take after a block transfer has completed +// <id> dmac_blockact_14 +#ifndef CONF_DMAC_BLOCKACT_14 +#define CONF_DMAC_BLOCKACT_14 0 +#endif + +// <o> Event Output Selection +// <0=> Event generation disabled +// <1=> Event strobe when block transfer complete +// <3=> Event strobe when beat transfer complete +// <i> Defines the event output selection +// <id> dmac_evosel_14 +#ifndef CONF_DMAC_EVOSEL_14 +#define CONF_DMAC_EVOSEL_14 0 +#endif +// </e> + +// <e> Channel 15 settings +// <id> dmac_channel_15_settings +#ifndef CONF_DMAC_CHANNEL_15_SETTINGS +#define CONF_DMAC_CHANNEL_15_SETTINGS 0 +#endif + +// <q> Channel Enable +// <i> Indicates whether channel 15 is enabled or not +// <id> dmac_enable_15 +#ifndef CONF_DMAC_ENABLE_15 +#define CONF_DMAC_ENABLE_15 0 +#endif + +// <q> Channel Run in Standby +// <i> Indicates whether channel 15 is running in standby mode or not +// <id> dmac_runstdby_15 +#ifndef CONF_DMAC_RUNSTDBY_15 +#define CONF_DMAC_RUNSTDBY_15 0 +#endif + +// <o> Trigger action +// <0=> One trigger required for each block transfer +// <2=> One trigger required for each beat transfer +// <3=> One trigger required for each transaction +// <i> Defines the trigger action used for a transfer +// <id> dmac_trigact_15 +#ifndef CONF_DMAC_TRIGACT_15 +#define CONF_DMAC_TRIGACT_15 0 +#endif + +// <o> Trigger source +// <0x00=> Only software/event triggers +// <0x01=> RTC Timestamp +// <0x02=> SERCOM0 RX Trigger +// <0x03=> SERCOM0 TX Trigger +// <0x04=> SERCOM1 RX Trigger +// <0x05=> SERCOM1 TX Trigger +// <0x06=> SERCOM2 RX Trigger +// <0x07=> SERCOM2 TX Trigger +// <0x08=> SERCOM3 RX Trigger +// <0x09=> SERCOM3 TX Trigger +// <0x0A=> SERCOM4 RX Trigger +// <0x0B=> SERCOM4 TX Trigger +// <0x0C=> SERCOM5 RX Trigger +// <0x0D=> SERCOM5 TX Trigger +// <0x0E=> TCC0 Overflow Trigger +// <0x0F=> TCC0 Match/Compare 0 Trigger +// <0x10=> TCC0 Match/Compare 1 Trigger +// <0x11=> TCC0 Match/Compare 2 Trigger +// <0x12=> TCC0 Match/Compare 3 Trigger +// <0x13=> TC0 Overflow Trigger +// <0x14=> TC0 Match/Compare 0 Trigger +// <0x15=> TC0 Match/Compare 1 Trigger +// <0x16=> TC1 Overflow Trigger +// <0x17=> TC1 Match/Compare 0 Trigger +// <0x18=> TC1 Match/Compare 1 Trigger +// <0x19=> TC2 Overflow Trigger +// <0x1A=> TC2 Match/Compare 0 Trigger +// <0x1B=> TC2 Match/Compare 1 Trigger +// <0x1C=> TC3 Overflow Trigger +// <0x1D=> TC3 Match/Compare 0 Trigger +// <0x1E=> TC3 Match/Compare 1 Trigger +// <0x1F=> ADC Result Ready Trigger +// <0x20=> SLCD Display Memory Update Trigger +// <0x21=> SLCD Automated Character Mapping Data Ready Trigger +// <0x22=> SLCD Automated Bit Mapping Data Ready Trigger +// <0x23=> AES Write Trigger +// <0x24=> AES Read Trigger +// <0x25=> PTC End of Conversion Trigger +// <0x26=> PTC Sequence Trigger +// <0x27=> PTC Window Comparator Trigger +// <i> Defines the peripheral trigger which is source of the transfer +// <id> dmac_trifsrc_15 +#ifndef CONF_DMAC_TRIGSRC_15 +#define CONF_DMAC_TRIGSRC_15 0 +#endif + +// <o> Channel Arbitration Level +// <0=> Channel priority 0 +// <1=> Channel priority 1 +// <2=> Channel priority 2 +// <3=> Channel priority 3 +// <i> Defines the arbitration level for this channel +// <id> dmac_lvl_15 +#ifndef CONF_DMAC_LVL_15 +#define CONF_DMAC_LVL_15 0 +#endif + +// <q> Channel Event Output +// <i> Indicates whether channel event generation is enabled or not +// <id> dmac_evoe_15 +#ifndef CONF_DMAC_EVOE_15 +#define CONF_DMAC_EVOE_15 0 +#endif + +// <q> Channel Event Input +// <i> Indicates whether channel event reception is enabled or not +// <id> dmac_evie_15 +#ifndef CONF_DMAC_EVIE_15 +#define CONF_DMAC_EVIE_15 0 +#endif + +// <o> Event Input Action +// <0=> No action +// <1=> Normal transfer and conditional transfer on strobe trigger +// <2=> Conditional transfer trigger +// <3=> Conditional block transfer +// <4=> Channel suspend operation +// <5=> Channel resume operation +// <6=> Skip next block suspend action +// <i> Defines the event input action +// <id> dmac_evact_15 +#ifndef CONF_DMAC_EVACT_15 +#define CONF_DMAC_EVACT_15 0 +#endif + +// <o> Address Increment Step Size +// <0=> Next ADDR = ADDR + (BEATSIZE + 1) * 1 +// <1=> Next ADDR = ADDR + (BEATSIZE + 1) * 2 +// <2=> Next ADDR = ADDR + (BEATSIZE + 1) * 4 +// <3=> Next ADDR = ADDR + (BEATSIZE + 1) * 8 +// <4=> Next ADDR = ADDR + (BEATSIZE + 1) * 16 +// <5=> Next ADDR = ADDR + (BEATSIZE + 1) * 32 +// <6=> Next ADDR = ADDR + (BEATSIZE + 1) * 64 +// <7=> Next ADDR = ADDR + (BEATSIZE + 1) * 128 +// <i> Defines the address increment step size, applies to source or destination address +// <id> dmac_stepsize_15 +#ifndef CONF_DMAC_STEPSIZE_15 +#define CONF_DMAC_STEPSIZE_15 0 +#endif + +// <o> Step Selection +// <0=> Step size settings apply to the destination address +// <1=> Step size settings apply to the source address +// <i> Defines whether source or destination addresses are using the step size settings +// <id> dmac_stepsel_15 +#ifndef CONF_DMAC_STEPSEL_15 +#define CONF_DMAC_STEPSEL_15 0 +#endif + +// <q> Source Address Increment +// <i> Indicates whether the source address incrementation is enabled or not +// <id> dmac_srcinc_15 +#ifndef CONF_DMAC_SRCINC_15 +#define CONF_DMAC_SRCINC_15 0 +#endif + +// <q> Destination Address Increment +// <i> Indicates whether the destination address incrementation is enabled or not +// <id> dmac_dstinc_15 +#ifndef CONF_DMAC_DSTINC_15 +#define CONF_DMAC_DSTINC_15 0 +#endif + +// <o> Beat Size +// <0=> 8-bit bus transfer +// <1=> 16-bit bus transfer +// <2=> 32-bit bus transfer +// <i> Defines the size of one beat +// <id> dmac_beatsize_15 +#ifndef CONF_DMAC_BEATSIZE_15 +#define CONF_DMAC_BEATSIZE_15 0 +#endif + +// <o> Block Action +// <0=> Channel will be disabled if it is the last block transfer in the transaction +// <1=> Channel will be disabled if it is the last block transfer in the transaction and block interrupt +// <2=> Channel suspend operation is complete +// <3=> Both channel suspend operation and block interrupt +// <i> Defines the the DMAC should take after a block transfer has completed +// <id> dmac_blockact_15 +#ifndef CONF_DMAC_BLOCKACT_15 +#define CONF_DMAC_BLOCKACT_15 0 +#endif + +// <o> Event Output Selection +// <0=> Event generation disabled +// <1=> Event strobe when block transfer complete +// <3=> Event strobe when beat transfer complete +// <i> Defines the event output selection +// <id> dmac_evosel_15 +#ifndef CONF_DMAC_EVOSEL_15 +#define CONF_DMAC_EVOSEL_15 0 +#endif +// </e> + +// </e> + +// <<< end of configuration section >>> + +#endif // HPL_DMAC_CONFIG_H diff --git a/watch-library/shared/config/hpl_eic_config.h b/watch-library/shared/config/hpl_eic_config.h new file mode 100644 index 00000000..be54c2e1 --- /dev/null +++ b/watch-library/shared/config/hpl_eic_config.h @@ -0,0 +1,736 @@ +/* Auto-generated config file hpl_eic_config.h */ +#ifndef HPL_EIC_CONFIG_H +#define HPL_EIC_CONFIG_H + +// <<< Use Configuration Wizard in Context Menu >>> + +// <h> Basic Settings +// <o> Clock Selection +// <i> Indicates which clock used, The EIC can be clocked either by GCLK_EIC when higher frequency than 32KHz is required for filtering or +// <i> either by CLK_ULP32K when power consumption is the priority. +// <0x0=> Clocked by GCLK +// <0x1=> Clocked by ULPOSC32K +// <id> eic_arch_cksel +#ifndef CONF_EIC_CKSEL +#define CONF_EIC_CKSEL 0 +#endif + +// </h> + +// <e> Non-Maskable Interrupt Control +// <id> eic_arch_nmi_ctrl +#ifndef CONF_EIC_ENABLE_NMI_CTRL +#define CONF_EIC_ENABLE_NMI_CTRL 0 +#endif + +// <q> Non-Maskable Interrupt Filter Enable +// <i> Indicates whether the mon-maskable interrupt filter is enabled or not +// <id> eic_arch_nmifilten +#ifndef CONF_EIC_NMIFILTEN +#define CONF_EIC_NMIFILTEN 0 +#endif + +// <y> Non-Maskable Interrupt Sense +// <EIC_NMICTRL_NMISENSE_NONE_Val"> No detection +// <EIC_NMICTRL_NMISENSE_RISE_Val"> Rising-edge detection +// <EIC_NMICTRL_NMISENSE_FALL_Val"> Falling-edge detection +// <EIC_NMICTRL_NMISENSE_BOTH_Val"> Both-edges detection +// <EIC_NMICTRL_NMISENSE_HIGH_Val"> High-level detection +// <EIC_NMICTRL_NMISENSE_LOW_Val"> Low-level detection +// <i> This defines non-maskable interrupt sense +// <id> eic_arch_nmisense +#ifndef CONF_EIC_NMISENSE +#define CONF_EIC_NMISENSE EIC_NMICTRL_NMISENSE_NONE_Val +#endif + +// <q> Asynchronous Edge Detection Mode +// <i> Indicates the interrupt detection mode operated synchronously or asynchronousl +// <id> eic_arch_nmiasynch +#ifndef CONF_EIC_NMIASYNCH +#define CONF_EIC_NMIASYNCH 0 +#endif +// </e> + +// <e> Interrupt 0 Settings +// <id> eic_arch_enable_irq_setting0 +#ifndef CONF_EIC_ENABLE_IRQ_SETTING0 +#define CONF_EIC_ENABLE_IRQ_SETTING0 0 +#endif + +// <q> External Interrupt 0 Filter Enable +// <i> Indicates whether the external interrupt 0 filter is enabled or not +// <id> eic_arch_filten0 +#ifndef CONF_EIC_FILTEN0 +#define CONF_EIC_FILTEN0 1 +#endif + +// <q> External Interrupt 0 Event Output Enable +// <i> Indicates whether the external interrupt 0 event output is enabled or not +// <id> eic_arch_extinteo0 +#ifndef CONF_EIC_EXTINTEO0 +#define CONF_EIC_EXTINTEO0 0 +#endif + +// <y> Input 0 Sense Configuration +// <EIC_NMICTRL_NMISENSE_NONE_Val"> No detection +// <EIC_NMICTRL_NMISENSE_RISE_Val"> Rising-edge detection +// <EIC_NMICTRL_NMISENSE_FALL_Val"> Falling-edge detection +// <EIC_NMICTRL_NMISENSE_BOTH_Val"> Both-edges detection +// <EIC_NMICTRL_NMISENSE_HIGH_Val"> High-level detection +// <EIC_NMICTRL_NMISENSE_LOW_Val"> Low-level detection +// <i> This defines input sense trigger +// <id> eic_arch_sense0 +#ifndef CONF_EIC_SENSE0 +#define CONF_EIC_SENSE0 EIC_NMICTRL_NMISENSE_NONE_Val +#endif + +// <q> External Interrupt 0 Asynchronous Edge Detection Mode +// <i> Indicates the external interrupt 0 detection mode operated synchronously or asynchronousl +// <id> eic_arch_asynch0 +#ifndef CONF_EIC_ASYNCH0 +#define CONF_EIC_ASYNCH0 0 +#endif + +// </e> + +// <e> Interrupt 1 Settings +// <id> eic_arch_enable_irq_setting1 +#ifndef CONF_EIC_ENABLE_IRQ_SETTING1 +#define CONF_EIC_ENABLE_IRQ_SETTING1 0 +#endif + +// <q> External Interrupt 1 Filter Enable +// <i> Indicates whether the external interrupt 1 filter is enabled or not +// <id> eic_arch_filten1 +#ifndef CONF_EIC_FILTEN1 +#define CONF_EIC_FILTEN1 1 +#endif + +// <q> External Interrupt 1 Event Output Enable +// <i> Indicates whether the external interrupt 1 event output is enabled or not +// <id> eic_arch_extinteo1 +#ifndef CONF_EIC_EXTINTEO1 +#define CONF_EIC_EXTINTEO1 0 +#endif + +// <y> Input 1 Sense Configuration +// <EIC_NMICTRL_NMISENSE_NONE_Val"> No detection +// <EIC_NMICTRL_NMISENSE_RISE_Val"> Rising-edge detection +// <EIC_NMICTRL_NMISENSE_FALL_Val"> Falling-edge detection +// <EIC_NMICTRL_NMISENSE_BOTH_Val"> Both-edges detection +// <EIC_NMICTRL_NMISENSE_HIGH_Val"> High-level detection +// <EIC_NMICTRL_NMISENSE_LOW_Val"> Low-level detection +// <i> This defines input sense trigger +// <id> eic_arch_sense1 +#ifndef CONF_EIC_SENSE1 +#define CONF_EIC_SENSE1 EIC_NMICTRL_NMISENSE_NONE_Val +#endif + +// <q> External Interrupt 1 Asynchronous Edge Detection Mode +// <i> Indicates the external interrupt 1 detection mode operated synchronously or asynchronousl +// <id> eic_arch_asynch1 +#ifndef CONF_EIC_ASYNCH1 +#define CONF_EIC_ASYNCH1 0 +#endif + +// </e> + +// <e> Interrupt 2 Settings +// <id> eic_arch_enable_irq_setting2 +#ifndef CONF_EIC_ENABLE_IRQ_SETTING2 +#define CONF_EIC_ENABLE_IRQ_SETTING2 0 +#endif + +// <q> External Interrupt 2 Filter Enable +// <i> Indicates whether the external interrupt 2 filter is enabled or not +// <id> eic_arch_filten2 +#ifndef CONF_EIC_FILTEN2 +#define CONF_EIC_FILTEN2 1 +#endif + +// <q> External Interrupt 2 Event Output Enable +// <i> Indicates whether the external interrupt 2 event output is enabled or not +// <id> eic_arch_extinteo2 +#ifndef CONF_EIC_EXTINTEO2 +#define CONF_EIC_EXTINTEO2 0 +#endif + +// <y> Input 2 Sense Configuration +// <EIC_NMICTRL_NMISENSE_NONE_Val"> No detection +// <EIC_NMICTRL_NMISENSE_RISE_Val"> Rising-edge detection +// <EIC_NMICTRL_NMISENSE_FALL_Val"> Falling-edge detection +// <EIC_NMICTRL_NMISENSE_BOTH_Val"> Both-edges detection +// <EIC_NMICTRL_NMISENSE_HIGH_Val"> High-level detection +// <EIC_NMICTRL_NMISENSE_LOW_Val"> Low-level detection +// <i> This defines input sense trigger +// <id> eic_arch_sense2 +#ifndef CONF_EIC_SENSE2 +#define CONF_EIC_SENSE2 EIC_NMICTRL_NMISENSE_NONE_Val +#endif + +// <q> External Interrupt 2 Asynchronous Edge Detection Mode +// <i> Indicates the external interrupt 2 detection mode operated synchronously or asynchronousl +// <id> eic_arch_asynch2 +#ifndef CONF_EIC_ASYNCH2 +#define CONF_EIC_ASYNCH2 0 +#endif + +// </e> + +// <e> Interrupt 3 Settings +// <id> eic_arch_enable_irq_setting3 +#ifndef CONF_EIC_ENABLE_IRQ_SETTING3 +#define CONF_EIC_ENABLE_IRQ_SETTING3 0 +#endif + +// <q> External Interrupt 3 Filter Enable +// <i> Indicates whether the external interrupt 3 filter is enabled or not +// <id> eic_arch_filten3 +#ifndef CONF_EIC_FILTEN3 +#define CONF_EIC_FILTEN3 1 +#endif + +// <q> External Interrupt 3 Event Output Enable +// <i> Indicates whether the external interrupt 3 event output is enabled or not +// <id> eic_arch_extinteo3 +#ifndef CONF_EIC_EXTINTEO3 +#define CONF_EIC_EXTINTEO3 0 +#endif + +// <y> Input 3 Sense Configuration +// <EIC_NMICTRL_NMISENSE_NONE_Val"> No detection +// <EIC_NMICTRL_NMISENSE_RISE_Val"> Rising-edge detection +// <EIC_NMICTRL_NMISENSE_FALL_Val"> Falling-edge detection +// <EIC_NMICTRL_NMISENSE_BOTH_Val"> Both-edges detection +// <EIC_NMICTRL_NMISENSE_HIGH_Val"> High-level detection +// <EIC_NMICTRL_NMISENSE_LOW_Val"> Low-level detection +// <i> This defines input sense trigger +// <id> eic_arch_sense3 +#ifndef CONF_EIC_SENSE3 +#define CONF_EIC_SENSE3 EIC_NMICTRL_NMISENSE_NONE_Val +#endif + +// <q> External Interrupt 3 Asynchronous Edge Detection Mode +// <i> Indicates the external interrupt 3 detection mode operated synchronously or asynchronousl +// <id> eic_arch_asynch3 +#ifndef CONF_EIC_ASYNCH3 +#define CONF_EIC_ASYNCH3 0 +#endif + +// </e> + +// <e> Interrupt 4 Settings +// <id> eic_arch_enable_irq_setting4 +#ifndef CONF_EIC_ENABLE_IRQ_SETTING4 +#define CONF_EIC_ENABLE_IRQ_SETTING4 0 +#endif + +// <q> External Interrupt 4 Filter Enable +// <i> Indicates whether the external interrupt 4 filter is enabled or not +// <id> eic_arch_filten4 +#ifndef CONF_EIC_FILTEN4 +#define CONF_EIC_FILTEN4 1 +#endif + +// <q> External Interrupt 4 Event Output Enable +// <i> Indicates whether the external interrupt 4 event output is enabled or not +// <id> eic_arch_extinteo4 +#ifndef CONF_EIC_EXTINTEO4 +#define CONF_EIC_EXTINTEO4 0 +#endif + +// <y> Input 4 Sense Configuration +// <EIC_NMICTRL_NMISENSE_NONE_Val"> No detection +// <EIC_NMICTRL_NMISENSE_RISE_Val"> Rising-edge detection +// <EIC_NMICTRL_NMISENSE_FALL_Val"> Falling-edge detection +// <EIC_NMICTRL_NMISENSE_BOTH_Val"> Both-edges detection +// <EIC_NMICTRL_NMISENSE_HIGH_Val"> High-level detection +// <EIC_NMICTRL_NMISENSE_LOW_Val"> Low-level detection +// <i> This defines input sense trigger +// <id> eic_arch_sense4 +#ifndef CONF_EIC_SENSE4 +#define CONF_EIC_SENSE4 EIC_NMICTRL_NMISENSE_NONE_Val +#endif + +// <q> External Interrupt 4 Asynchronous Edge Detection Mode +// <i> Indicates the external interrupt 4 detection mode operated synchronously or asynchronousl +// <id> eic_arch_asynch4 +#ifndef CONF_EIC_ASYNCH4 +#define CONF_EIC_ASYNCH4 0 +#endif + +// </e> + +// <e> Interrupt 5 Settings +// <id> eic_arch_enable_irq_setting5 +#ifndef CONF_EIC_ENABLE_IRQ_SETTING5 +#define CONF_EIC_ENABLE_IRQ_SETTING5 0 +#endif + +// <q> External Interrupt 5 Filter Enable +// <i> Indicates whether the external interrupt 5 filter is enabled or not +// <id> eic_arch_filten5 +#ifndef CONF_EIC_FILTEN5 +#define CONF_EIC_FILTEN5 1 +#endif + +// <q> External Interrupt 5 Event Output Enable +// <i> Indicates whether the external interrupt 5 event output is enabled or not +// <id> eic_arch_extinteo5 +#ifndef CONF_EIC_EXTINTEO5 +#define CONF_EIC_EXTINTEO5 0 +#endif + +// <y> Input 5 Sense Configuration +// <EIC_NMICTRL_NMISENSE_NONE_Val"> No detection +// <EIC_NMICTRL_NMISENSE_RISE_Val"> Rising-edge detection +// <EIC_NMICTRL_NMISENSE_FALL_Val"> Falling-edge detection +// <EIC_NMICTRL_NMISENSE_BOTH_Val"> Both-edges detection +// <EIC_NMICTRL_NMISENSE_HIGH_Val"> High-level detection +// <EIC_NMICTRL_NMISENSE_LOW_Val"> Low-level detection +// <i> This defines input sense trigger +// <id> eic_arch_sense5 +#ifndef CONF_EIC_SENSE5 +#define CONF_EIC_SENSE5 EIC_NMICTRL_NMISENSE_NONE_Val +#endif + +// <q> External Interrupt 5 Asynchronous Edge Detection Mode +// <i> Indicates the external interrupt 5 detection mode operated synchronously or asynchronousl +// <id> eic_arch_asynch5 +#ifndef CONF_EIC_ASYNCH5 +#define CONF_EIC_ASYNCH5 0 +#endif + +// </e> + +// <e> Interrupt 6 Settings +// <id> eic_arch_enable_irq_setting6 +#ifndef CONF_EIC_ENABLE_IRQ_SETTING6 +#define CONF_EIC_ENABLE_IRQ_SETTING6 0 +#endif + +// <q> External Interrupt 6 Filter Enable +// <i> Indicates whether the external interrupt 6 filter is enabled or not +// <id> eic_arch_filten6 +#ifndef CONF_EIC_FILTEN6 +#define CONF_EIC_FILTEN6 1 +#endif + +// <q> External Interrupt 6 Event Output Enable +// <i> Indicates whether the external interrupt 6 event output is enabled or not +// <id> eic_arch_extinteo6 +#ifndef CONF_EIC_EXTINTEO6 +#define CONF_EIC_EXTINTEO6 0 +#endif + +// <y> Input 6 Sense Configuration +// <EIC_NMICTRL_NMISENSE_NONE_Val"> No detection +// <EIC_NMICTRL_NMISENSE_RISE_Val"> Rising-edge detection +// <EIC_NMICTRL_NMISENSE_FALL_Val"> Falling-edge detection +// <EIC_NMICTRL_NMISENSE_BOTH_Val"> Both-edges detection +// <EIC_NMICTRL_NMISENSE_HIGH_Val"> High-level detection +// <EIC_NMICTRL_NMISENSE_LOW_Val"> Low-level detection +// <i> This defines input sense trigger +// <id> eic_arch_sense6 +#ifndef CONF_EIC_SENSE6 +#define CONF_EIC_SENSE6 EIC_NMICTRL_NMISENSE_NONE_Val +#endif + +// <q> External Interrupt 6 Asynchronous Edge Detection Mode +// <i> Indicates the external interrupt 6 detection mode operated synchronously or asynchronousl +// <id> eic_arch_asynch6 +#ifndef CONF_EIC_ASYNCH6 +#define CONF_EIC_ASYNCH6 0 +#endif + +// </e> + +// <e> Interrupt 7 Settings +// <id> eic_arch_enable_irq_setting7 +#ifndef CONF_EIC_ENABLE_IRQ_SETTING7 +#define CONF_EIC_ENABLE_IRQ_SETTING7 0 +#endif + +// <q> External Interrupt 7 Filter Enable +// <i> Indicates whether the external interrupt 7 filter is enabled or not +// <id> eic_arch_filten7 +#ifndef CONF_EIC_FILTEN7 +#define CONF_EIC_FILTEN7 1 +#endif + +// <q> External Interrupt 7 Event Output Enable +// <i> Indicates whether the external interrupt 7 event output is enabled or not +// <id> eic_arch_extinteo7 +#ifndef CONF_EIC_EXTINTEO7 +#define CONF_EIC_EXTINTEO7 0 +#endif + +// <y> Input 7 Sense Configuration +// <EIC_NMICTRL_NMISENSE_NONE_Val"> No detection +// <EIC_NMICTRL_NMISENSE_RISE_Val"> Rising-edge detection +// <EIC_NMICTRL_NMISENSE_FALL_Val"> Falling-edge detection +// <EIC_NMICTRL_NMISENSE_BOTH_Val"> Both-edges detection +// <EIC_NMICTRL_NMISENSE_HIGH_Val"> High-level detection +// <EIC_NMICTRL_NMISENSE_LOW_Val"> Low-level detection +// <i> This defines input sense trigger +// <id> eic_arch_sense7 +#ifndef CONF_EIC_SENSE7 +#define CONF_EIC_SENSE7 EIC_NMICTRL_NMISENSE_NONE_Val +#endif + +// <q> External Interrupt 7 Asynchronous Edge Detection Mode +// <i> Indicates the external interrupt 7 detection mode operated synchronously or asynchronousl +// <id> eic_arch_asynch7 +#ifndef CONF_EIC_ASYNCH7 +#define CONF_EIC_ASYNCH7 0 +#endif + +// </e> + +// <e> Interrupt 8 Settings +// <id> eic_arch_enable_irq_setting8 +#ifndef CONF_EIC_ENABLE_IRQ_SETTING8 +#define CONF_EIC_ENABLE_IRQ_SETTING8 0 +#endif + +// <q> External Interrupt 8 Filter Enable +// <i> Indicates whether the external interrupt 8 filter is enabled or not +// <id> eic_arch_filten8 +#ifndef CONF_EIC_FILTEN8 +#define CONF_EIC_FILTEN8 0 +#endif + +// <q> External Interrupt 8 Event Output Enable +// <i> Indicates whether the external interrupt 8 event output is enabled or not +// <id> eic_arch_extinteo8 +#ifndef CONF_EIC_EXTINTEO8 +#define CONF_EIC_EXTINTEO8 0 +#endif + +// <y> Input 8 Sense Configuration +// <EIC_NMICTRL_NMISENSE_NONE_Val"> No detection +// <EIC_NMICTRL_NMISENSE_RISE_Val"> Rising-edge detection +// <EIC_NMICTRL_NMISENSE_FALL_Val"> Falling-edge detection +// <EIC_NMICTRL_NMISENSE_BOTH_Val"> Both-edges detection +// <EIC_NMICTRL_NMISENSE_HIGH_Val"> High-level detection +// <EIC_NMICTRL_NMISENSE_LOW_Val"> Low-level detection +// <i> This defines input sense trigger +// <id> eic_arch_sense8 +#ifndef CONF_EIC_SENSE8 +#define CONF_EIC_SENSE8 EIC_NMICTRL_NMISENSE_NONE_Val +#endif + +// <q> External Interrupt 8 Asynchronous Edge Detection Mode +// <i> Indicates the external interrupt 8 detection mode operated synchronously or asynchronousl +// <id> eic_arch_asynch8 +#ifndef CONF_EIC_ASYNCH8 +#define CONF_EIC_ASYNCH8 0 +#endif + +// </e> + +// <e> Interrupt 9 Settings +// <id> eic_arch_enable_irq_setting9 +#ifndef CONF_EIC_ENABLE_IRQ_SETTING9 +#define CONF_EIC_ENABLE_IRQ_SETTING9 0 +#endif + +// <q> External Interrupt 9 Filter Enable +// <i> Indicates whether the external interrupt 9 filter is enabled or not +// <id> eic_arch_filten9 +#ifndef CONF_EIC_FILTEN9 +#define CONF_EIC_FILTEN9 0 +#endif + +// <q> External Interrupt 9 Event Output Enable +// <i> Indicates whether the external interrupt 9 event output is enabled or not +// <id> eic_arch_extinteo9 +#ifndef CONF_EIC_EXTINTEO9 +#define CONF_EIC_EXTINTEO9 0 +#endif + +// <y> Input 9 Sense Configuration +// <EIC_NMICTRL_NMISENSE_NONE_Val"> No detection +// <EIC_NMICTRL_NMISENSE_RISE_Val"> Rising-edge detection +// <EIC_NMICTRL_NMISENSE_FALL_Val"> Falling-edge detection +// <EIC_NMICTRL_NMISENSE_BOTH_Val"> Both-edges detection +// <EIC_NMICTRL_NMISENSE_HIGH_Val"> High-level detection +// <EIC_NMICTRL_NMISENSE_LOW_Val"> Low-level detection +// <i> This defines input sense trigger +// <id> eic_arch_sense9 +#ifndef CONF_EIC_SENSE9 +#define CONF_EIC_SENSE9 EIC_NMICTRL_NMISENSE_NONE_Val +#endif + +// <q> External Interrupt 9 Asynchronous Edge Detection Mode +// <i> Indicates the external interrupt 9 detection mode operated synchronously or asynchronousl +// <id> eic_arch_asynch9 +#ifndef CONF_EIC_ASYNCH9 +#define CONF_EIC_ASYNCH9 0 +#endif + +// </e> + +// <e> Interrupt 10 Settings +// <id> eic_arch_enable_irq_setting10 +#ifndef CONF_EIC_ENABLE_IRQ_SETTING10 +#define CONF_EIC_ENABLE_IRQ_SETTING10 0 +#endif + +// <q> External Interrupt 10 Filter Enable +// <i> Indicates whether the external interrupt 10 filter is enabled or not +// <id> eic_arch_filten10 +#ifndef CONF_EIC_FILTEN10 +#define CONF_EIC_FILTEN10 0 +#endif + +// <q> External Interrupt 10 Event Output Enable +// <i> Indicates whether the external interrupt 10 event output is enabled or not +// <id> eic_arch_extinteo10 +#ifndef CONF_EIC_EXTINTEO10 +#define CONF_EIC_EXTINTEO10 0 +#endif + +// <y> Input 10 Sense Configuration +// <EIC_NMICTRL_NMISENSE_NONE_Val"> No detection +// <EIC_NMICTRL_NMISENSE_RISE_Val"> Rising-edge detection +// <EIC_NMICTRL_NMISENSE_FALL_Val"> Falling-edge detection +// <EIC_NMICTRL_NMISENSE_BOTH_Val"> Both-edges detection +// <EIC_NMICTRL_NMISENSE_HIGH_Val"> High-level detection +// <EIC_NMICTRL_NMISENSE_LOW_Val"> Low-level detection +// <i> This defines input sense trigger +// <id> eic_arch_sense10 +#ifndef CONF_EIC_SENSE10 +#define CONF_EIC_SENSE10 EIC_NMICTRL_NMISENSE_NONE_Val +#endif + +// <q> External Interrupt 10 Asynchronous Edge Detection Mode +// <i> Indicates the external interrupt 10 detection mode operated synchronously or asynchronousl +// <id> eic_arch_asynch10 +#ifndef CONF_EIC_ASYNCH10 +#define CONF_EIC_ASYNCH10 0 +#endif + +// </e> + +// <e> Interrupt 11 Settings +// <id> eic_arch_enable_irq_setting11 +#ifndef CONF_EIC_ENABLE_IRQ_SETTING11 +#define CONF_EIC_ENABLE_IRQ_SETTING11 0 +#endif + +// <q> External Interrupt 11 Filter Enable +// <i> Indicates whether the external interrupt 11 filter is enabled or not +// <id> eic_arch_filten11 +#ifndef CONF_EIC_FILTEN11 +#define CONF_EIC_FILTEN11 0 +#endif + +// <q> External Interrupt 11 Event Output Enable +// <i> Indicates whether the external interrupt 11 event output is enabled or not +// <id> eic_arch_extinteo11 +#ifndef CONF_EIC_EXTINTEO11 +#define CONF_EIC_EXTINTEO11 0 +#endif + +// <y> Input 11 Sense Configuration +// <EIC_NMICTRL_NMISENSE_NONE_Val"> No detection +// <EIC_NMICTRL_NMISENSE_RISE_Val"> Rising-edge detection +// <EIC_NMICTRL_NMISENSE_FALL_Val"> Falling-edge detection +// <EIC_NMICTRL_NMISENSE_BOTH_Val"> Both-edges detection +// <EIC_NMICTRL_NMISENSE_HIGH_Val"> High-level detection +// <EIC_NMICTRL_NMISENSE_LOW_Val"> Low-level detection +// <i> This defines input sense trigger +// <id> eic_arch_sense11 +#ifndef CONF_EIC_SENSE11 +#define CONF_EIC_SENSE11 EIC_NMICTRL_NMISENSE_NONE_Val +#endif + +// <q> External Interrupt 11 Asynchronous Edge Detection Mode +// <i> Indicates the external interrupt 11 detection mode operated synchronously or asynchronousl +// <id> eic_arch_asynch11 +#ifndef CONF_EIC_ASYNCH11 +#define CONF_EIC_ASYNCH11 0 +#endif + +// </e> + +// <e> Interrupt 12 Settings +// <id> eic_arch_enable_irq_setting12 +#ifndef CONF_EIC_ENABLE_IRQ_SETTING12 +#define CONF_EIC_ENABLE_IRQ_SETTING12 0 +#endif + +// <q> External Interrupt 12 Filter Enable +// <i> Indicates whether the external interrupt 12 filter is enabled or not +// <id> eic_arch_filten12 +#ifndef CONF_EIC_FILTEN12 +#define CONF_EIC_FILTEN12 0 +#endif + +// <q> External Interrupt 12 Event Output Enable +// <i> Indicates whether the external interrupt 12 event output is enabled or not +// <id> eic_arch_extinteo12 +#ifndef CONF_EIC_EXTINTEO12 +#define CONF_EIC_EXTINTEO12 0 +#endif + +// <y> Input 12 Sense Configuration +// <EIC_NMICTRL_NMISENSE_NONE_Val"> No detection +// <EIC_NMICTRL_NMISENSE_RISE_Val"> Rising-edge detection +// <EIC_NMICTRL_NMISENSE_FALL_Val"> Falling-edge detection +// <EIC_NMICTRL_NMISENSE_BOTH_Val"> Both-edges detection +// <EIC_NMICTRL_NMISENSE_HIGH_Val"> High-level detection +// <EIC_NMICTRL_NMISENSE_LOW_Val"> Low-level detection +// <i> This defines input sense trigger +// <id> eic_arch_sense12 +#ifndef CONF_EIC_SENSE12 +#define CONF_EIC_SENSE12 EIC_NMICTRL_NMISENSE_NONE_Val +#endif + +// <q> External Interrupt 12 Asynchronous Edge Detection Mode +// <i> Indicates the external interrupt 12 detection mode operated synchronously or asynchronousl +// <id> eic_arch_asynch12 +#ifndef CONF_EIC_ASYNCH12 +#define CONF_EIC_ASYNCH12 0 +#endif + +// </e> + +// <e> Interrupt 13 Settings +// <id> eic_arch_enable_irq_setting13 +#ifndef CONF_EIC_ENABLE_IRQ_SETTING13 +#define CONF_EIC_ENABLE_IRQ_SETTING13 0 +#endif + +// <q> External Interrupt 13 Filter Enable +// <i> Indicates whether the external interrupt 13 filter is enabled or not +// <id> eic_arch_filten13 +#ifndef CONF_EIC_FILTEN13 +#define CONF_EIC_FILTEN13 0 +#endif + +// <q> External Interrupt 13 Event Output Enable +// <i> Indicates whether the external interrupt 13 event output is enabled or not +// <id> eic_arch_extinteo13 +#ifndef CONF_EIC_EXTINTEO13 +#define CONF_EIC_EXTINTEO13 0 +#endif + +// <y> Input 13 Sense Configuration +// <EIC_NMICTRL_NMISENSE_NONE_Val"> No detection +// <EIC_NMICTRL_NMISENSE_RISE_Val"> Rising-edge detection +// <EIC_NMICTRL_NMISENSE_FALL_Val"> Falling-edge detection +// <EIC_NMICTRL_NMISENSE_BOTH_Val"> Both-edges detection +// <EIC_NMICTRL_NMISENSE_HIGH_Val"> High-level detection +// <EIC_NMICTRL_NMISENSE_LOW_Val"> Low-level detection +// <i> This defines input sense trigger +// <id> eic_arch_sense13 +#ifndef CONF_EIC_SENSE13 +#define CONF_EIC_SENSE13 EIC_NMICTRL_NMISENSE_NONE_Val +#endif + +// <q> External Interrupt 13 Asynchronous Edge Detection Mode +// <i> Indicates the external interrupt 13 detection mode operated synchronously or asynchronousl +// <id> eic_arch_asynch13 +#ifndef CONF_EIC_ASYNCH13 +#define CONF_EIC_ASYNCH13 0 +#endif + +// </e> + +// <e> Interrupt 14 Settings +// <id> eic_arch_enable_irq_setting14 +#ifndef CONF_EIC_ENABLE_IRQ_SETTING14 +#define CONF_EIC_ENABLE_IRQ_SETTING14 0 +#endif + +// <q> External Interrupt 14 Filter Enable +// <i> Indicates whether the external interrupt 14 filter is enabled or not +// <id> eic_arch_filten14 +#ifndef CONF_EIC_FILTEN14 +#define CONF_EIC_FILTEN14 0 +#endif + +// <q> External Interrupt 14 Event Output Enable +// <i> Indicates whether the external interrupt 14 event output is enabled or not +// <id> eic_arch_extinteo14 +#ifndef CONF_EIC_EXTINTEO14 +#define CONF_EIC_EXTINTEO14 0 +#endif + +// <y> Input 14 Sense Configuration +// <EIC_NMICTRL_NMISENSE_NONE_Val"> No detection +// <EIC_NMICTRL_NMISENSE_RISE_Val"> Rising-edge detection +// <EIC_NMICTRL_NMISENSE_FALL_Val"> Falling-edge detection +// <EIC_NMICTRL_NMISENSE_BOTH_Val"> Both-edges detection +// <EIC_NMICTRL_NMISENSE_HIGH_Val"> High-level detection +// <EIC_NMICTRL_NMISENSE_LOW_Val"> Low-level detection +// <i> This defines input sense trigger +// <id> eic_arch_sense14 +#ifndef CONF_EIC_SENSE14 +#define CONF_EIC_SENSE14 EIC_NMICTRL_NMISENSE_NONE_Val +#endif + +// <q> External Interrupt 14 Asynchronous Edge Detection Mode +// <i> Indicates the external interrupt 14 detection mode operated synchronously or asynchronousl +// <id> eic_arch_asynch14 +#ifndef CONF_EIC_ASYNCH14 +#define CONF_EIC_ASYNCH14 0 +#endif + +// </e> + +// <e> Interrupt 15 Settings +// <id> eic_arch_enable_irq_setting15 +#ifndef CONF_EIC_ENABLE_IRQ_SETTING15 +#define CONF_EIC_ENABLE_IRQ_SETTING15 0 +#endif + +// <q> External Interrupt 15 Filter Enable +// <i> Indicates whether the external interrupt 15 filter is enabled or not +// <id> eic_arch_filten15 +#ifndef CONF_EIC_FILTEN15 +#define CONF_EIC_FILTEN15 0 +#endif + +// <q> External Interrupt 15 Event Output Enable +// <i> Indicates whether the external interrupt 15 event output is enabled or not +// <id> eic_arch_extinteo15 +#ifndef CONF_EIC_EXTINTEO15 +#define CONF_EIC_EXTINTEO15 0 +#endif + +// <y> Input 15 Sense Configuration +// <EIC_NMICTRL_NMISENSE_NONE_Val"> No detection +// <EIC_NMICTRL_NMISENSE_RISE_Val"> Rising-edge detection +// <EIC_NMICTRL_NMISENSE_FALL_Val"> Falling-edge detection +// <EIC_NMICTRL_NMISENSE_BOTH_Val"> Both-edges detection +// <EIC_NMICTRL_NMISENSE_HIGH_Val"> High-level detection +// <EIC_NMICTRL_NMISENSE_LOW_Val"> Low-level detection +// <i> This defines input sense trigger +// <id> eic_arch_sense15 +#ifndef CONF_EIC_SENSE15 +#define CONF_EIC_SENSE15 EIC_NMICTRL_NMISENSE_NONE_Val +#endif + +// <q> External Interrupt 15 Asynchronous Edge Detection Mode +// <i> Indicates the external interrupt 15 detection mode operated synchronously or asynchronousl +// <id> eic_arch_asynch15 +#ifndef CONF_EIC_ASYNCH15 +#define CONF_EIC_ASYNCH15 0 +#endif + +// </e> + +// this is still a hack: if the user wants to use PA02 (alarm button) as an RTC interrupt pin and PB02 (9-pin A2) on the EIC, we don't support that. +// TODO item: refactor out our reliance on the ASF external interrupt driver. - joey 11/30 +#ifdef CRYSTALLESS +#define CONFIG_EIC_EXTINT_MAP {0, PIN_PB00}, {1, PIN_PB01}, {2, PIN_PA02}, {3, PIN_PB03}, {5, PIN_PB05}, {7, PIN_PA07}, +#else +#define CONFIG_EIC_EXTINT_MAP {0, PIN_PB00}, {1, PIN_PB01}, {2, PIN_PA02}, {3, PIN_PB03}, {6, PIN_PA22}, {7, PIN_PA23}, +#endif + +// <<< end of configuration section >>> + +#endif // HPL_EIC_CONFIG_H diff --git a/watch-library/shared/config/hpl_gclk_config.h b/watch-library/shared/config/hpl_gclk_config.h new file mode 100644 index 00000000..ee7aace3 --- /dev/null +++ b/watch-library/shared/config/hpl_gclk_config.h @@ -0,0 +1,388 @@ +/* Auto-generated config file hpl_gclk_config.h */ +#ifndef HPL_GCLK_CONFIG_H +#define HPL_GCLK_CONFIG_H + +// <<< Use Configuration Wizard in Context Menu >>> + +// <e> Generic clock generator 0 configuration +// <i> Indicates whether generic clock 0 configuration is enabled or not +// <id> enable_gclk_gen_0 +#ifndef CONF_GCLK_GENERATOR_0_CONFIG +#define CONF_GCLK_GENERATOR_0_CONFIG 1 +#endif + +// <h> Generic Clock Generator Control +// <y> Generic clock generator 0 source +// <GCLK_GENCTRL_SRC_XOSC"> External Crystal Oscillator 0.4-32MHz (XOSC) +// <GCLK_GENCTRL_SRC_GCLKIN"> Generic clock generator input pad +// <GCLK_GENCTRL_SRC_GCLKGEN1"> Generic clock generator 1 +// <GCLK_GENCTRL_SRC_OSCULP32K"> 32kHz Ultra Low Power Internal Oscillator (OSCULP32K) +// <GCLK_GENCTRL_SRC_XOSC32K"> 32kHz External Crystal Oscillator (XOSC32K) +// <GCLK_GENCTRL_SRC_OSC16M"> 16MHz Internal Oscillator (OSC16M) +// <GCLK_GENCTRL_SRC_DFLL48M"> Digital Frequency Locked Loop (DFLL48M) +// <GCLK_GENCTRL_SRC_DPLL96M"> Fractional Digital Phase Locked Loop (FDPLL96M) +// <i> This defines the clock source for generic clock generator 0 +// <id> gclk_gen_0_oscillator +#ifndef CONF_GCLK_GEN_0_SOURCE +#define CONF_GCLK_GEN_0_SOURCE GCLK_GENCTRL_SRC_OSC16M +#endif + +// <q> Run in Standby +// <i> Indicates whether Run in Standby is enabled or not +// <id> gclk_arch_gen_0_runstdby +#ifndef CONF_GCLK_GEN_0_RUNSTDBY +#define CONF_GCLK_GEN_0_RUNSTDBY 0 +#endif + +// <q> Divide Selection +// <i> Indicates whether Divide Selection is enabled or not +//<id> gclk_gen_0_div_sel +#ifndef CONF_GCLK_GEN_0_DIVSEL +#define CONF_GCLK_GEN_0_DIVSEL 0 +#endif + +// <q> Output Enable +// <i> Indicates whether Output Enable is enabled or not +// <id> gclk_arch_gen_0_oe +#ifndef CONF_GCLK_GEN_0_OE +#define CONF_GCLK_GEN_0_OE 0 +#endif + +// <q> Output Off Value +// <i> Indicates whether Output Off Value is enabled or not +// <id> gclk_arch_gen_0_oov +#ifndef CONF_GCLK_GEN_0_OOV +#define CONF_GCLK_GEN_0_OOV 0 +#endif + +// <q> Improve Duty Cycle +// <i> Indicates whether Improve Duty Cycle is enabled or not +// <id> gclk_arch_gen_0_idc +#ifndef CONF_GCLK_GEN_0_IDC +#define CONF_GCLK_GEN_0_IDC 0 +#endif + +// <q> Generic Clock Generator Enable +// <i> Indicates whether Generic Clock Generator Enable is enabled or not +// <id> gclk_arch_gen_0_enable +#ifndef CONF_GCLK_GEN_0_GENEN +#define CONF_GCLK_GEN_0_GENEN 1 +#endif +// </h> + +//<h> Generic Clock Generator Division +//<o> Generic clock generator 0 division <0x0000-0xFFFF> +// <id> gclk_gen_0_div +#ifndef CONF_GCLK_GEN_0_DIV +#define CONF_GCLK_GEN_0_DIV 1 +#endif +// </h> +// </e> + +// <e> Generic clock generator 1 configuration +// <i> Indicates whether generic clock 1 configuration is enabled or not +// <id> enable_gclk_gen_1 +#ifndef CONF_GCLK_GENERATOR_1_CONFIG +#define CONF_GCLK_GENERATOR_1_CONFIG 0 +#endif + +// <h> Generic Clock Generator Control +// <y> Generic clock generator 1 source +// <GCLK_GENCTRL_SRC_XOSC"> External Crystal Oscillator 0.4-32MHz (XOSC) +// <GCLK_GENCTRL_SRC_GCLKIN"> Generic clock generator input pad +// <GCLK_GENCTRL_SRC_OSCULP32K"> 32kHz Ultra Low Power Internal Oscillator (OSCULP32K) +// <GCLK_GENCTRL_SRC_XOSC32K"> 32kHz External Crystal Oscillator (XOSC32K) +// <GCLK_GENCTRL_SRC_OSC16M"> 16MHz Internal Oscillator (OSC16M) +// <GCLK_GENCTRL_SRC_DFLL48M"> Digital Frequency Locked Loop (DFLL48M) +// <GCLK_GENCTRL_SRC_DPLL96M"> Fractional Digital Phase Locked Loop (FDPLL96M) +// <i> This defines the clock source for generic clock generator 1 +// <id> gclk_gen_1_oscillator +#ifndef CONF_GCLK_GEN_1_SOURCE +#define CONF_GCLK_GEN_1_SOURCE GCLK_GENCTRL_SRC_XOSC +#endif + +// <q> Run in Standby +// <i> Indicates whether Run in Standby is enabled or not +// <id> gclk_arch_gen_1_runstdby +#ifndef CONF_GCLK_GEN_1_RUNSTDBY +#define CONF_GCLK_GEN_1_RUNSTDBY 0 +#endif + +// <q> Divide Selection +// <i> Indicates whether Divide Selection is enabled or not +//<id> gclk_gen_1_div_sel +#ifndef CONF_GCLK_GEN_1_DIVSEL +#define CONF_GCLK_GEN_1_DIVSEL 0 +#endif + +// <q> Output Enable +// <i> Indicates whether Output Enable is enabled or not +// <id> gclk_arch_gen_1_oe +#ifndef CONF_GCLK_GEN_1_OE +#define CONF_GCLK_GEN_1_OE 0 +#endif + +// <q> Output Off Value +// <i> Indicates whether Output Off Value is enabled or not +// <id> gclk_arch_gen_1_oov +#ifndef CONF_GCLK_GEN_1_OOV +#define CONF_GCLK_GEN_1_OOV 0 +#endif + +// <q> Improve Duty Cycle +// <i> Indicates whether Improve Duty Cycle is enabled or not +// <id> gclk_arch_gen_1_idc +#ifndef CONF_GCLK_GEN_1_IDC +#define CONF_GCLK_GEN_1_IDC 0 +#endif + +// <q> Generic Clock Generator Enable +// <i> Indicates whether Generic Clock Generator Enable is enabled or not +// <id> gclk_arch_gen_1_enable +#ifndef CONF_GCLK_GEN_1_GENEN +#define CONF_GCLK_GEN_1_GENEN 0 +#endif +// </h> + +//<h> Generic Clock Generator Division +//<o> Generic clock generator 1 division <0x0000-0xFFFF> +// <id> gclk_gen_1_div +#ifndef CONF_GCLK_GEN_1_DIV +#define CONF_GCLK_GEN_1_DIV 1 +#endif +// </h> +// </e> + +// <e> Generic clock generator 2 configuration +// <i> Indicates whether generic clock 2 configuration is enabled or not +// <id> enable_gclk_gen_2 +#ifndef CONF_GCLK_GENERATOR_2_CONFIG +#define CONF_GCLK_GENERATOR_2_CONFIG 0 +#endif + +// <h> Generic Clock Generator Control +// <y> Generic clock generator 2 source +// <GCLK_GENCTRL_SRC_XOSC"> External Crystal Oscillator 0.4-32MHz (XOSC) +// <GCLK_GENCTRL_SRC_GCLKIN"> Generic clock generator input pad +// <GCLK_GENCTRL_SRC_GCLKGEN1"> Generic clock generator 1 +// <GCLK_GENCTRL_SRC_OSCULP32K"> 32kHz Ultra Low Power Internal Oscillator (OSCULP32K) +// <GCLK_GENCTRL_SRC_XOSC32K"> 32kHz External Crystal Oscillator (XOSC32K) +// <GCLK_GENCTRL_SRC_OSC16M"> 16MHz Internal Oscillator (OSC16M) +// <GCLK_GENCTRL_SRC_DFLL48M"> Digital Frequency Locked Loop (DFLL48M) +// <GCLK_GENCTRL_SRC_DPLL96M"> Fractional Digital Phase Locked Loop (FDPLL96M) +// <i> This defines the clock source for generic clock generator 2 +// <id> gclk_gen_2_oscillator +#ifndef CONF_GCLK_GEN_2_SOURCE +#define CONF_GCLK_GEN_2_SOURCE GCLK_GENCTRL_SRC_XOSC +#endif + +// <q> Run in Standby +// <i> Indicates whether Run in Standby is enabled or not +// <id> gclk_arch_gen_2_runstdby +#ifndef CONF_GCLK_GEN_2_RUNSTDBY +#define CONF_GCLK_GEN_2_RUNSTDBY 0 +#endif + +// <q> Divide Selection +// <i> Indicates whether Divide Selection is enabled or not +//<id> gclk_gen_2_div_sel +#ifndef CONF_GCLK_GEN_2_DIVSEL +#define CONF_GCLK_GEN_2_DIVSEL 0 +#endif + +// <q> Output Enable +// <i> Indicates whether Output Enable is enabled or not +// <id> gclk_arch_gen_2_oe +#ifndef CONF_GCLK_GEN_2_OE +#define CONF_GCLK_GEN_2_OE 0 +#endif + +// <q> Output Off Value +// <i> Indicates whether Output Off Value is enabled or not +// <id> gclk_arch_gen_2_oov +#ifndef CONF_GCLK_GEN_2_OOV +#define CONF_GCLK_GEN_2_OOV 0 +#endif + +// <q> Improve Duty Cycle +// <i> Indicates whether Improve Duty Cycle is enabled or not +// <id> gclk_arch_gen_2_idc +#ifndef CONF_GCLK_GEN_2_IDC +#define CONF_GCLK_GEN_2_IDC 0 +#endif + +// <q> Generic Clock Generator Enable +// <i> Indicates whether Generic Clock Generator Enable is enabled or not +// <id> gclk_arch_gen_2_enable +#ifndef CONF_GCLK_GEN_2_GENEN +#define CONF_GCLK_GEN_2_GENEN 0 +#endif +// </h> + +//<h> Generic Clock Generator Division +//<o> Generic clock generator 2 division <0x0000-0xFFFF> +// <id> gclk_gen_2_div +#ifndef CONF_GCLK_GEN_2_DIV +#define CONF_GCLK_GEN_2_DIV 1 +#endif +// </h> +// </e> + +// <e> Generic clock generator 3 configuration +// <i> Indicates whether generic clock 3 configuration is enabled or not +// <id> enable_gclk_gen_3 +#ifndef CONF_GCLK_GENERATOR_3_CONFIG +#define CONF_GCLK_GENERATOR_3_CONFIG 1 +#endif + +// <h> Generic Clock Generator Control +// <y> Generic clock generator 3 source +// <GCLK_GENCTRL_SRC_XOSC"> External Crystal Oscillator 0.4-32MHz (XOSC) +// <GCLK_GENCTRL_SRC_GCLKIN"> Generic clock generator input pad +// <GCLK_GENCTRL_SRC_GCLKGEN1"> Generic clock generator 1 +// <GCLK_GENCTRL_SRC_OSCULP32K"> 32kHz Ultra Low Power Internal Oscillator (OSCULP32K) +// <GCLK_GENCTRL_SRC_XOSC32K"> 32kHz External Crystal Oscillator (XOSC32K) +// <GCLK_GENCTRL_SRC_OSC16M"> 16MHz Internal Oscillator (OSC16M) +// <GCLK_GENCTRL_SRC_DFLL48M"> Digital Frequency Locked Loop (DFLL48M) +// <GCLK_GENCTRL_SRC_DPLL96M"> Fractional Digital Phase Locked Loop (FDPLL96M) +// <i> This defines the clock source for generic clock generator 3 +// <id> gclk_gen_3_oscillator +#ifndef CONF_GCLK_GEN_3_SOURCE +#ifdef CRYSTALLESS +#define CONF_GCLK_GEN_3_SOURCE GCLK_GENCTRL_SRC_OSCULP32K +#else +#define CONF_GCLK_GEN_3_SOURCE GCLK_GENCTRL_SRC_XOSC32K +#endif + +#endif + +// <q> Run in Standby +// <i> Indicates whether Run in Standby is enabled or not +// <id> gclk_arch_gen_3_runstdby +#ifndef CONF_GCLK_GEN_3_RUNSTDBY +#define CONF_GCLK_GEN_3_RUNSTDBY 1 +#endif + +// <q> Divide Selection +// <i> Indicates whether Divide Selection is enabled or not +//<id> gclk_gen_3_div_sel +#ifndef CONF_GCLK_GEN_3_DIVSEL +#define CONF_GCLK_GEN_3_DIVSEL 0 +#endif + +// <q> Output Enable +// <i> Indicates whether Output Enable is enabled or not +// <id> gclk_arch_gen_3_oe +#ifndef CONF_GCLK_GEN_3_OE +#define CONF_GCLK_GEN_3_OE 0 +#endif + +// <q> Output Off Value +// <i> Indicates whether Output Off Value is enabled or not +// <id> gclk_arch_gen_3_oov +#ifndef CONF_GCLK_GEN_3_OOV +#define CONF_GCLK_GEN_3_OOV 0 +#endif + +// <q> Improve Duty Cycle +// <i> Indicates whether Improve Duty Cycle is enabled or not +// <id> gclk_arch_gen_3_idc +#ifndef CONF_GCLK_GEN_3_IDC +#define CONF_GCLK_GEN_3_IDC 1 +#endif + +// <q> Generic Clock Generator Enable +// <i> Indicates whether Generic Clock Generator Enable is enabled or not +// <id> gclk_arch_gen_3_enable +#ifndef CONF_GCLK_GEN_3_GENEN +#define CONF_GCLK_GEN_3_GENEN 1 +#endif +// </h> + +//<h> Generic Clock Generator Division +//<o> Generic clock generator 3 division <0x0000-0xFFFF> +// <id> gclk_gen_3_div +#ifndef CONF_GCLK_GEN_3_DIV +#define CONF_GCLK_GEN_3_DIV 1 +#endif +// </h> +// </e> + +// <e> Generic clock generator 4 configuration +// <i> Indicates whether generic clock 4 configuration is enabled or not +// <id> enable_gclk_gen_4 +#ifndef CONF_GCLK_GENERATOR_4_CONFIG +#define CONF_GCLK_GENERATOR_4_CONFIG 0 +#endif + +// <h> Generic Clock Generator Control +// <y> Generic clock generator 4 source +// <GCLK_GENCTRL_SRC_XOSC"> External Crystal Oscillator 0.4-32MHz (XOSC) +// <GCLK_GENCTRL_SRC_GCLKIN"> Generic clock generator input pad +// <GCLK_GENCTRL_SRC_GCLKGEN1"> Generic clock generator 1 +// <GCLK_GENCTRL_SRC_OSCULP32K"> 32kHz Ultra Low Power Internal Oscillator (OSCULP32K) +// <GCLK_GENCTRL_SRC_XOSC32K"> 32kHz External Crystal Oscillator (XOSC32K) +// <GCLK_GENCTRL_SRC_OSC16M"> 16MHz Internal Oscillator (OSC16M) +// <GCLK_GENCTRL_SRC_DFLL48M"> Digital Frequency Locked Loop (DFLL48M) +// <GCLK_GENCTRL_SRC_DPLL96M"> Fractional Digital Phase Locked Loop (FDPLL96M) +// <i> This defines the clock source for generic clock generator 4 +// <id> gclk_gen_4_oscillator +#ifndef CONF_GCLK_GEN_4_SOURCE +#define CONF_GCLK_GEN_4_SOURCE GCLK_GENCTRL_SRC_XOSC +#endif + +// <q> Run in Standby +// <i> Indicates whether Run in Standby is enabled or not +// <id> gclk_arch_gen_4_runstdby +#ifndef CONF_GCLK_GEN_4_RUNSTDBY +#define CONF_GCLK_GEN_4_RUNSTDBY 0 +#endif + +// <q> Divide Selection +// <i> Indicates whether Divide Selection is enabled or not +//<id> gclk_gen_4_div_sel +#ifndef CONF_GCLK_GEN_4_DIVSEL +#define CONF_GCLK_GEN_4_DIVSEL 0 +#endif + +// <q> Output Enable +// <i> Indicates whether Output Enable is enabled or not +// <id> gclk_arch_gen_4_oe +#ifndef CONF_GCLK_GEN_4_OE +#define CONF_GCLK_GEN_4_OE 0 +#endif + +// <q> Output Off Value +// <i> Indicates whether Output Off Value is enabled or not +// <id> gclk_arch_gen_4_oov +#ifndef CONF_GCLK_GEN_4_OOV +#define CONF_GCLK_GEN_4_OOV 0 +#endif + +// <q> Improve Duty Cycle +// <i> Indicates whether Improve Duty Cycle is enabled or not +// <id> gclk_arch_gen_4_idc +#ifndef CONF_GCLK_GEN_4_IDC +#define CONF_GCLK_GEN_4_IDC 0 +#endif + +// <q> Generic Clock Generator Enable +// <i> Indicates whether Generic Clock Generator Enable is enabled or not +// <id> gclk_arch_gen_4_enable +#ifndef CONF_GCLK_GEN_4_GENEN +#define CONF_GCLK_GEN_4_GENEN 0 +#endif +// </h> + +//<h> Generic Clock Generator Division +//<o> Generic clock generator 4 division <0x0000-0xFFFF> +// <id> gclk_gen_4_div +#ifndef CONF_GCLK_GEN_4_DIV +#define CONF_GCLK_GEN_4_DIV 1 +#endif +// </h> +// </e> + +// <<< end of configuration section >>> + +#endif // HPL_GCLK_CONFIG_H diff --git a/watch-library/shared/config/hpl_mclk_config.h b/watch-library/shared/config/hpl_mclk_config.h new file mode 100644 index 00000000..3358edcf --- /dev/null +++ b/watch-library/shared/config/hpl_mclk_config.h @@ -0,0 +1,85 @@ +/* Auto-generated config file hpl_mclk_config.h */ +#ifndef HPL_MCLK_CONFIG_H +#define HPL_MCLK_CONFIG_H + +// <<< Use Configuration Wizard in Context Menu >>> + +#include <peripheral_clk_config.h> + +// <e> System Configuration +// <i> Indicates whether configuration for system is enabled or not +// <id> enable_cpu_clock +#ifndef CONF_SYSTEM_CONFIG +#define CONF_SYSTEM_CONFIG 1 +#endif + +// <h> Basic settings +// <y> CPU Clock source +// <GCLK_PCHCTRL_GEN_GCLK0_Val"> Generic clock generator 0 +// <i> This defines the clock source for the CPU +// <id> cpu_clock_source +#ifndef CONF_CPU_SRC +#define CONF_CPU_SRC GCLK_PCHCTRL_GEN_GCLK0_Val +#endif + +// <y> CPU Clock Division Factor +// <MCLK_CPUDIV_CPUDIV_DIV1_Val"> 1 +// <MCLK_CPUDIV_CPUDIV_DIV2_Val"> 2 +// <MCLK_CPUDIV_CPUDIV_DIV4_Val"> 4 +// <MCLK_CPUDIV_CPUDIV_DIV8_Val"> 8 +// <MCLK_CPUDIV_CPUDIV_DIV16_Val"> 16 +// <MCLK_CPUDIV_CPUDIV_DIV32_Val"> 32 +// <MCLK_CPUDIV_CPUDIV_DIV64_Val"> 64 +// <MCLK_CPUDIV_CPUDIV_DIV128_Val"> 128 +// <i> Prescalar for CPU clock +// <id> cpu_div +#ifndef CONF_MCLK_CPUDIV +#define CONF_MCLK_CPUDIV MCLK_CPUDIV_CPUDIV_DIV1_Val +#endif + +// <y> Backup Clock Division +// <MCLK_BUPDIV_BUPDIV_DIV1_Val"> Divide by 1 +// <MCLK_BUPDIV_BUPDIV_DIV2_Val"> Divide by 2 +// <MCLK_BUPDIV_BUPDIV_DIV4_Val"> Divide by 4 +// <MCLK_BUPDIV_BUPDIV_DIV8_Val"> Divide by 8 +// <MCLK_BUPDIV_BUPDIV_DIV16_Val"> Divide by 16 +// <MCLK_BUPDIV_BUPDIV_DIV32_Val"> Divide by 32 +// <MCLK_BUPDIV_BUPDIV_DIV64_Val"> Divide by 64 +// <MCLK_BUPDIV_BUPDIV_DIV128_Val"> Divide by 128 +// <id> mclk_arch_bupdiv +#ifndef CONF_MCLK_BUPDIV +#define CONF_MCLK_BUPDIV MCLK_BUPDIV_BUPDIV_DIV1_Val +#endif +// </h> + +// <h> NVM Settings +// <o> NVM Wait States +// <i> These bits select the number of wait states for a read operation. +// <0=> 0 +// <1=> 1 +// <2=> 2 +// <3=> 3 +// <4=> 4 +// <5=> 5 +// <6=> 6 +// <7=> 7 +// <8=> 8 +// <9=> 9 +// <10=> 10 +// <11=> 11 +// <12=> 12 +// <13=> 13 +// <14=> 14 +// <15=> 15 +// <id> nvm_wait_states +#ifndef CONF_NVM_WAIT_STATE +#define CONF_NVM_WAIT_STATE 0 +#endif + +// </h> + +// </e> + +// <<< end of configuration section >>> + +#endif // HPL_MCLK_CONFIG_H diff --git a/watch-library/shared/config/hpl_nvmctrl_config.h b/watch-library/shared/config/hpl_nvmctrl_config.h new file mode 100755 index 00000000..76d49bac --- /dev/null +++ b/watch-library/shared/config/hpl_nvmctrl_config.h @@ -0,0 +1,38 @@ +/* Auto-generated config file hpl_nvmctrl_config.h */ +#ifndef HPL_NVMCTRL_CONFIG_H +#define HPL_NVMCTRL_CONFIG_H + +// <<< Use Configuration Wizard in Context Menu >>> + +// <h> Basic Settings + +// <o> Read Mode Selection +// <0x00=> No Miss Penalty +// <0x01=> Low Power +// <0x02=> Deterministic +// <id> nvm_arch_read_mode +#ifndef CONF_NVM_READ_MODE +#define CONF_NVM_READ_MODE 1 +#endif + +// <o> Power Reduction Mode During Sleep +// <0x00=> Wake On Access +// <0x01=> Wake Up Instant +// <0x03=> Disabled +// <id> nvm_arch_sleepprm +#ifndef CONF_NVM_SLEEPPRM +#define CONF_NVM_SLEEPPRM 0 +#endif + +// <q> Cache Disable +// <i> Indicate whether cache is disable or not +// <id> nvm_arch_cache +#ifndef CONF_NVM_CACHE +#define CONF_NVM_CACHE 0 +#endif + +// </h> + +// <<< end of configuration section >>> + +#endif // HPL_NVMCTRL_CONFIG_H diff --git a/watch-library/shared/config/hpl_osc32kctrl_config.h b/watch-library/shared/config/hpl_osc32kctrl_config.h new file mode 100644 index 00000000..540f1c60 --- /dev/null +++ b/watch-library/shared/config/hpl_osc32kctrl_config.h @@ -0,0 +1,177 @@ +/* Auto-generated config file hpl_osc32kctrl_config.h */ +#ifndef HPL_OSC32KCTRL_CONFIG_H +#define HPL_OSC32KCTRL_CONFIG_H + +// <<< Use Configuration Wizard in Context Menu >>> + +// <e> RTC Source configuration +// <id> enable_rtc_source +#ifndef CONF_RTCCTRL_CONFIG +#define CONF_RTCCTRL_CONFIG 0 +#endif + +// <h> RTC source control +// <y> RTC Clock Source Selection +// <GCLK_GENCTRL_SRC_OSCULP32K"> 32kHz Ultra Low Power Internal Oscillator (OSCULP32K) +// <GCLK_GENCTRL_SRC_XOSC32K"> 32kHz External Crystal Oscillator (XOSC32K) +// <i> This defines the clock source for RTC +// <id> rtc_source_oscillator +#ifndef CONF_RTCCTRL_SRC +#ifdef CRYSTALLESS +#define CONF_RTCCTRL_SRC GCLK_GENCTRL_SRC_OSCULP32K +#else +#define CONF_RTCCTRL_SRC GCLK_GENCTRL_SRC_XOSC32K +#endif +#endif + +// <q> Use 1 kHz output +// <id> rtc_1khz_selection +#ifndef CONF_RTCCTRL_1KHZ + +#define CONF_RTCCTRL_1KHZ 1 + +#endif + +#if CONF_RTCCTRL_SRC == GCLK_GENCTRL_SRC_OSCULP32K +#define CONF_RTCCTRL (CONF_RTCCTRL_1KHZ ? OSC32KCTRL_RTCCTRL_RTCSEL_ULP1K_Val : OSC32KCTRL_RTCCTRL_RTCSEL_ULP32K_Val) +#elif CONF_RTCCTRL_SRC == GCLK_GENCTRL_SRC_XOSC32K +#define CONF_RTCCTRL (CONF_RTCCTRL_1KHZ ? OSC32KCTRL_RTCCTRL_RTCSEL_XOSC1K_Val : OSC32KCTRL_RTCCTRL_RTCSEL_XOSC32K_Val) +#else +#error unexpected CONF_RTCCTRL_SRC +#endif + +// </h> +// </e> +// <e> SLCD Source configuration +// <id> enable_slcd_source +#ifndef CONF_SLCDCTRL_CONFIG +#define CONF_SLCDCTRL_CONFIG 0 +#endif + +// <h> SLCD source control +// <y> SLCD Clock Source Selection +// <GCLK_GENCTRL_SRC_OSCULP32K"> 32kHz Ultra Low Power Internal Oscillator (OSCULP32K) +// <GCLK_GENCTRL_SRC_XOSC32K"> 32kHz External Crystal Oscillator (XOSC32K) +// <i> This defines the clock source for SLCD +// <id> slcd_source_oscillator +#ifndef CONF_SLCDCTRL_SRC +#define CONF_SLCDCTRL_SRC GCLK_GENCTRL_SRC_XOSC32K +#endif + +// </h> +// </e> +// <e> 32kHz External Crystal Oscillator Configuration +// <i> Indicates whether configuration for External 32K Osc is enabled or not +// <id> enable_xosc32k +#ifndef CONF_XOSC32K_CONFIG +#define CONF_XOSC32K_CONFIG 1 +#endif + +// <h> 32kHz External Crystal Oscillator Control +// <q> Oscillator enable +// <i> Indicates whether 32kHz External Crystal Oscillator is enabled or not +// <id> xosc32k_arch_enable +#ifndef CONF_XOSC32K_ENABLE +#define CONF_XOSC32K_ENABLE 1 +#endif + +// <o> Start-Up Time +// <0x0=>62592us +// <0x1=>125092us +// <0x2=>500092us +// <0x3=>1000092us +// <0x4=>2000092us +// <0x5=>4000092us +// <0x6=>8000092us +// <id> xosc32k_arch_startup +#ifndef CONF_XOSC32K_STARTUP +#define CONF_XOSC32K_STARTUP 0x3 +#endif + +// <q> On Demand Control +// <i> Indicates whether On Demand Control is enabled or not +// <id> xosc32k_arch_ondemand +#ifndef CONF_XOSC32K_ONDEMAND +#define CONF_XOSC32K_ONDEMAND 0 +#endif + +// <q> Run in Standby +// <i> Indicates whether Run in Standby is enabled or not +// <id> xosc32k_arch_runstdby +#ifndef CONF_XOSC32K_RUNSTDBY +#define CONF_XOSC32K_RUNSTDBY 1 +#endif + +// <q> 1kHz Output Enable +// <i> Indicates whether 1kHz Output is enabled or not +// <id> xosc32k_arch_en1k +#ifndef CONF_XOSC32K_EN1K +#define CONF_XOSC32K_EN1K 1 +#endif + +// <q> 32kHz Output Enable +// <i> Indicates whether 32kHz Output is enabled or not +// <id> xosc32k_arch_en32k +#ifndef CONF_XOSC32K_EN32K +#define CONF_XOSC32K_EN32K 1 +#endif + +// <q> Clock Switch Back +// <i> Indicates whether Clock Switch Back is enabled or not +// <id> xosc32k_arch_swben +#ifndef CONF_XOSC32K_SWBEN +#define CONF_XOSC32K_SWBEN 0 +#endif + +// <q> Clock Failure Detector +// <i> Indicates whether Clock Failure Detector is enabled or not +// <id> xosc32k_arch_cfden +#ifndef CONF_XOSC32K_CFDEN +#define CONF_XOSC32K_CFDEN 0 +#endif + +// <q> Clock Failure Detector Event Out +// <i> Indicates whether Clock Failure Detector Event Out is enabled or not +// <id> xosc32k_arch_cfdeo +#ifndef CONF_XOSC32K_CFDEO +#define CONF_XOSC32K_CFDEO 0 +#endif + +// <q> Crystal connected to XIN32/XOUT32 Enable +// <i> Indicates whether the connections between the I/O pads and the external clock or crystal oscillator is enabled or not +// <id> xosc32k_arch_xtalen +#ifndef CONF_XOSC32K_XTALEN +#define CONF_XOSC32K_XTALEN 1 +#endif + +// </h> +// </e> + +// <e> 32kHz Ultra Low Power Internal Oscillator Configuration +// <i> Indicates whether configuration for OSCULP32K is enabled or not +// <id> enable_osculp32k +#ifndef CONF_OSCULP32K_CONFIG +#define CONF_OSCULP32K_CONFIG 1 +#endif + +// <h> 32kHz Ultra Low Power Internal Oscillator Control + +// <q> Oscillator Calibration Control +// <i> Indicates whether Oscillator Calibration is enabled or not +// <id> osculp32k_calib_enable +#ifndef CONF_OSCULP32K_CALIB_ENABLE +#define CONF_OSCULP32K_CALIB_ENABLE 0 +#endif + +// <o> Oscillator Calibration <0x0-0x1F> +// <id> osculp32k_calib +#ifndef CONF_OSCULP32K_CALIB +#define CONF_OSCULP32K_CALIB 0x0 +#endif + +// </h> +// </e> + +// <<< end of configuration section >>> + +#endif // HPL_OSC32KCTRL_CONFIG_H diff --git a/watch-library/shared/config/hpl_oscctrl_config.h b/watch-library/shared/config/hpl_oscctrl_config.h new file mode 100644 index 00000000..ba2d42e6 --- /dev/null +++ b/watch-library/shared/config/hpl_oscctrl_config.h @@ -0,0 +1,483 @@ +/* Auto-generated config file hpl_oscctrl_config.h */ +#ifndef HPL_OSCCTRL_CONFIG_H +#define HPL_OSCCTRL_CONFIG_H + +// <<< Use Configuration Wizard in Context Menu >>> + +// <e> External Multipurpose Crystal Oscillator Configuration +// <i> Indicates whether configuration for XOSC is enabled or not +// <id> enable_xosc +#ifndef CONF_XOSC_CONFIG +#define CONF_XOSC_CONFIG 0 +#endif + +// <o> Frequency <400000-32000000> +// <i> Oscillation frequency of the resonator connected to the External Multipurpose Crystal Oscillator. +// <id> xosc_frequency +#ifndef CONF_XOSC_FREQUENCY +#define CONF_XOSC_FREQUENCY 400000 +#endif + +// <h> External Multipurpose Crystal Oscillator Control +// <q> Oscillator enable +// <i> Indicates whether External Multipurpose Crystal Oscillator is enabled or not +// <id> xosc_arch_enable +#ifndef CONF_XOSC_ENABLE +#define CONF_XOSC_ENABLE 0 +#endif + +// <o> Start-Up Time +// <0x0=>31us +// <0x1=>61us +// <0x2=>122us +// <0x3=>244us +// <0x4=>488us +// <0x5=>977us +// <0x6=>1953us +// <0x7=>3906us +// <0x8=>7813us +// <0x9=>15625us +// <0xA=>31250us +// <0xB=>62500us +// <0xC=>125000us +// <0xD=>250000us +// <0xE=>500000us +// <0xF=>1000000us +// <id> xosc_arch_startup +#ifndef CONF_XOSC_STARTUP +#define CONF_XOSC_STARTUP 0x0 +#endif + +// <q> Automatic Amplitude Gain Control +// <i> Indicates whether Automatic Amplitude Gain Control is enabled or not +// <id> xosc_arch_ampgc +#ifndef CONF_XOSC_AMPGC +#define CONF_XOSC_AMPGC 0 +#endif + +// <o> External Multipurpose Crystal Oscillator Gain +// <0x0=>2MHz +// <0x1=>4MHz +// <0x2=>8MHz +// <0x3=>16MHz +// <0x4=>30MHz +// <id> xosc_arch_gain +#ifndef CONF_XOSC_GAIN +#define CONF_XOSC_GAIN 0x0 +#endif + +// <q> On Demand Control +// <i> Indicates whether On Demand Control is enabled or not +// <id> xosc_arch_ondemand +#ifndef CONF_XOSC_ONDEMAND +#define CONF_XOSC_ONDEMAND 1 +#endif + +// <q> Run in Standby +// <i> Indicates whether Run in Standby is enabled or not +// <id> xosc_arch_runstdby +#ifndef CONF_XOSC_RUNSTDBY +#define CONF_XOSC_RUNSTDBY 0 +#endif + +// <q> Clock Switch Back +// <i> Indicates whether Clock Switch Back is enabled or not +// <id> xosc_arch_swben +#ifndef CONF_XOSC_SWBEN +#define CONF_XOSC_SWBEN 0 +#endif + +// <q> Clock Failure Detector +// <i> Indicates whether Clock Failure Detector is enabled or not +// <id> xosc_arch_cfden +#ifndef CONF_XOSC_CFDEN +#define CONF_XOSC_CFDEN 0 +#endif + +// <q> Clock Failure Detector Event Out +// <i> Indicates whether Clock Failure Detector Event Out is enabled or not +// <id> xosc_arch_cfdeo +#ifndef CONF_XOSC_CFDEO +#define CONF_XOSC_CFDEO 0 +#endif + +// <q> Crystal connected to XIN/XOUT Enable +// <i> Indicates whether the connections between the I/O pads and the external clock or crystal oscillator is enabled or not +// <id> xosc_arch_xtalen +#ifndef CONF_XOSC_XTALEN +#define CONF_XOSC_XTALEN 0 +#endif +//</h> +//</e> + +// <e> 16MHz Internal Oscillator Configuration +// <i> Indicates whether configuration for OSC8M is enabled or not +// <id> enable_osc16m +#ifndef CONF_OSC16M_CONFIG +#define CONF_OSC16M_CONFIG 1 +#endif + +// <h> 16MHz Internal Oscillator Control +// <q> Enable +// <i> Indicates whether 16MHz Internal Oscillator is enabled or not +// <id> osc16m_arch_enable +#ifndef CONF_OSC16M_ENABLE +#define CONF_OSC16M_ENABLE 1 +#endif + +// <q> On Demand Control +// <i> Indicates whether On Demand Control is enabled or not +// <id> osc16m_arch_ondemand +#ifndef CONF_OSC16M_ONDEMAND +#define CONF_OSC16M_ONDEMAND 1 +#endif + +// <q> Run in Standby +// <i> Indicates whether Run in Standby is enabled or not +// <id> osc16m_arch_runstdby +#ifndef CONF_OSC16M_RUNSTDBY +#define CONF_OSC16M_RUNSTDBY 0 +#endif + +// <y> Oscillator Frequency Selection(Mhz) +// <OSCCTRL_OSC16MCTRL_FSEL_4_Val"> 4 +// <OSCCTRL_OSC16MCTRL_FSEL_8_Val"> 8 +// <OSCCTRL_OSC16MCTRL_FSEL_12_Val"> 12 +// <OSCCTRL_OSC16MCTRL_FSEL_16_Val"> 16 +// <i> This defines the oscillator frequency (Mhz) +// <id> osc16m_freq +#ifndef CONF_OSC16M_FSEL +#define CONF_OSC16M_FSEL OSCCTRL_OSC16MCTRL_FSEL_4_Val +#endif + +// <q> Oscillator Calibration Control +// <i> Indicates whether Oscillator Calibration is enabled or not +// <id> osc16m_arch_calib_enable +#ifndef CONF_OSC16M_CALIB_ENABLE +#define CONF_OSC16M_CALIB_ENABLE 0 +#endif + +// <o> 4MHz Frequency Calibration <0x0-0x3F> +// <id> osc16m_arch_4m_fcal +#ifndef CONF_OSC16M_FCAL +#define CONF_OSC16M_4M_FCAL 0 +#endif + +// <o> 4MHz Temperature Calibration <0x0-0x3F> +// <id> osc16m_arch_4m_tcal +#ifndef CONF_OSC16M_TCAL +#define CONF_OSC16M_4M_TCAL 0 +#endif + +// <o> 8MHz Frequency Calibration <0x0-0x3F> +// <id> osc16m_arch_8m_fcal +#ifndef CONF_OSC16M_FCAL +#define CONF_OSC16M_8M_FCAL 0 +#endif + +// <o> 8MHz Temperature Calibration <0x0-0x3F> +// <id> osc16m_arch_8m_tcal +#ifndef CONF_OSC16M_TCAL +#define CONF_OSC16M_8M_TCAL 0 +#endif + +// <o> 12MHz Frequency Calibration <0x0-0x3F> +// <id> osc16m_arch_12m_fcal +#ifndef CONF_OSC16M_FCAL +#define CONF_OSC16M_12M_FCAL 0 +#endif + +// <o> 12MHz Temperature Calibration <0x0-0x3F> +// <id> osc16m_arch_12m_tcal +#ifndef CONF_OSC16M_TCAL +#define CONF_OSC16M_12M_TCAL 0 +#endif + +// <o> 16MHz Frequency Calibration <0x0-0x3F> +// <id> osc16m_arch_fcal +#ifndef CONF_OSC16M_FCAL +#define CONF_OSC16M_16M_FCAL 0 +#endif + +// <o> 16MHz Temperature Calibration <0x0-0x3F> +// <id> osc16m_arch_16m_tcal +#ifndef CONF_OSC16M_TCAL +#define CONF_OSC16M_16M_TCAL 0 +#endif +//</h> +//</e> + +// <e> DFLL Configuration +// <i> Indicates whether configuration for DFLL is enabled or not +// <id> enable_dfll48m +#ifndef CONF_DFLL_CONFIG +#define CONF_DFLL_CONFIG 0 +#endif + +// <y> Reference Clock Source +// <GCLK_PCHCTRL_GEN_GCLK0_Val"> Generic clock generator 0 +// <GCLK_PCHCTRL_GEN_GCLK1_Val"> Generic clock generator 1 +// <GCLK_PCHCTRL_GEN_GCLK2_Val"> Generic clock generator 2 +// <GCLK_PCHCTRL_GEN_GCLK3_Val"> Generic clock generator 3 +// <GCLK_PCHCTRL_GEN_GCLK4_Val"> Generic clock generator 4 +// <GCLK_PCHCTRL_GEN_GCLK5_Val"> Generic clock generator 5 +// <GCLK_PCHCTRL_GEN_GCLK6_Val"> Generic clock generator 6 +// <GCLK_PCHCTRL_GEN_GCLK7_Val"> Generic clock generator 7 +// <i> Select the clock source. +// <id> dfll48m_ref_clock +#ifndef CONF_DFLL_GCLK +#define CONF_DFLL_GCLK GCLK_PCHCTRL_GEN_GCLK3_Val +#endif + +// <h> Digital Frequency Locked Loop Control +// <q> DFLL Enable +// <i> Indicates whether DFLL is enabled or not +// <id> dfll48m_arch_enable +#ifndef CONF_DFLL_ENABLE +#define CONF_DFLL_ENABLE 0 +#endif + +// <q> Wait Lock +// <i> Indicates whether Wait Lock is enabled or not +// <id> dfll_arch_waitlock +#ifndef CONF_DFLL_WAITLOCK +#define CONF_DFLL_WAITLOCK 0 +#endif + +// <q> Bypass Coarse Lock +// <i> Indicates whether Bypass Coarse Lock is enabled or not +// <id> dfll_arch_bplckc +#ifndef CONF_DFLL_BPLCKC +#define CONF_DFLL_BPLCKC 0 +#endif + +// <q> Quick Lock Disable +// <i> Indicates whether Quick Lock Disable is enabled or not +// <id> dfll_arch_qldis +#ifndef CONF_DFLL_QLDIS +#define CONF_DFLL_QLDIS 0 +#endif + +// <q> Chill Cycle Disable +// <i> Indicates whether Chill Cycle Disable is enabled or not +// <id> dfll_arch_ccdis +#ifndef CONF_DFLL_CCDIS +#define CONF_DFLL_CCDIS 0 +#endif + +// <q> On Demand Control +// <i> Indicates whether On Demand Control is enabled or not +// <id> dfll_arch_ondemand +#ifndef CONF_DFLL_ONDEMAND +#define CONF_DFLL_ONDEMAND 1 +#endif + +// <q> Run in Standby +// <i> Indicates whether Run in Standby is enabled or not +// <id> dfll_arch_runstdby +#ifndef CONF_DFLL_RUNSTDBY +#define CONF_DFLL_RUNSTDBY 0 +#endif + +// <q> USB Clock Recovery Mode +// <i> Indicates whether USB Clock Recovery Mode is enabled or not +// <id> dfll_arch_usbcrm +#ifndef CONF_DFLL_USBCRM +#define CONF_DFLL_USBCRM 0 +#endif + +// <q> Lose Lock After Wake +// <i> Indicates whether Lose Lock After Wake is enabled or not +// <id> dfll_arch_llaw +#ifndef CONF_DFLL_LLAW +#define CONF_DFLL_LLAW 0 +#endif + +// <q> Stable DFLL Frequency +// <i> Indicates whether Stable DFLL Frequency is enabled or not +// <id> dfll_arch_stable +#ifndef CONF_DFLL_STABLE +#define CONF_DFLL_STABLE 0 +#endif + +// <o> Operating Mode Selection +// <0=>Open Loop Mode +// <1=>Closed Loop Mode +// <id> dfll48m_mode +#ifndef CONF_DFLL_MODE +#define CONF_DFLL_MODE 0 +#endif + +// <o> Coarse Maximum Step <0x0-0x1F> +// <id> dfll_arch_cstep +#ifndef CONF_DFLL_CSTEP +#define CONF_DFLL_CSTEP 1 +#endif + +// <o> Fine Maximum Step <0x0-0x3FF> +// <id> dfll_arch_fstep +#ifndef CONF_DFLL_FSTEP +#define CONF_DFLL_FSTEP 1 +#endif + +// <o> DFLL Multiply Factor <0x0-0xFFFF> +// <id> dfll48m_mul +#ifndef CONF_DFLL_MUL +#define CONF_DFLL_MUL 0 +#endif + +// <e> DFLL Calibration Overwrite +// <i> Indicates whether Overwrite Calibration value of DFLL +// <id> dfll_arch_calibration +#ifndef CONF_DFLL_OVERWRITE_CALIBRATION +#define CONF_DFLL_OVERWRITE_CALIBRATION 0 +#endif + +// <o> Coarse Value <0x0-0x3F> +// <id> dfll_arch_coarse +#ifndef CONF_DFLL_COARSE +#define CONF_DFLL_COARSE (0x1f / 4) +#endif + +// <o> Fine Value <0x0-0x3FF> +// <id> dfll_arch_fine +#ifndef CONF_DFLL_FINE +#define CONF_DFLL_FINE (0x200) +#endif + +//</e> + +//</h> + +//</e> + +// <e> DPLL Configuration +// <i> Indicates whether configuration for DPLL is enabled or not +// <id> enable_fdpll96m +#ifndef CONF_DPLL_CONFIG +#define CONF_DPLL_CONFIG 0 +#endif + +// <y> Reference Clock Source +// <GCLK_GENCTRL_SRC_XOSC32K"> 32kHz External Crystal Oscillator (XOSC32K) +// <GCLK_GENCTRL_SRC_XOSC"> External Crystal Oscillator 0.4-32MHz (XOSC) +// <GCLK_PCHCTRL_GEN_GCLK0_Val"> Generic clock generator 0 +// <GCLK_PCHCTRL_GEN_GCLK1_Val"> Generic clock generator 1 +// <GCLK_PCHCTRL_GEN_GCLK2_Val"> Generic clock generator 2 +// <GCLK_PCHCTRL_GEN_GCLK3_Val"> Generic clock generator 3 +// <GCLK_PCHCTRL_GEN_GCLK4_Val"> Generic clock generator 4 +// <GCLK_PCHCTRL_GEN_GCLK5_Val"> Generic clock generator 5 +// <GCLK_PCHCTRL_GEN_GCLK6_Val"> Generic clock generator 6 +// <GCLK_PCHCTRL_GEN_GCLK7_Val"> Generic clock generator 7 +// <i> Select the clock source. +// <id> fdpll96m_ref_clock +#ifndef CONF_DPLL_GCLK +#define CONF_DPLL_GCLK GCLK_GENCTRL_SRC_XOSC32K + +#endif + +// <h> Digital Phase Locked Loop Control +// <q> Enable +// <i> Indicates whether Digital Phase Locked Loop is enabled or not +// <id> fdpll96m_arch_enable +#ifndef CONF_DPLL_ENABLE +#define CONF_DPLL_ENABLE 0 +#endif + +// <q> On Demand Control +// <i> Indicates whether On Demand Control is enabled or not +// <id> fdpll96m_arch_ondemand +#ifndef CONF_DPLL_ONDEMAND +#define CONF_DPLL_ONDEMAND 1 +#endif + +// <q> Run in Standby +// <i> Indicates whether Run in Standby is enabled or not +// <id> fdpll96m_arch_runstdby +#ifndef CONF_DPLL_RUNSTDBY +#define CONF_DPLL_RUNSTDBY 0 +#endif + +// <o> Loop Divider Ratio Fractional Part <0x0-0xF> +// <id> fdpll96m_ldrfrac +#ifndef CONF_DPLL_LDRFRAC +#define CONF_DPLL_LDRFRAC 0xd +#endif + +// <o> Loop Divider Ratio Integer Part <0x0-0xFFF> +// <id> fdpll96m_ldr +#ifndef CONF_DPLL_LDR +#define CONF_DPLL_LDR 0x5b7 +#endif + +// <o> Clock Divider <0x0-0x3FF> +// <id> fdpll96m_clock_div +#ifndef CONF_DPLL_DIV +#define CONF_DPLL_DIV 0 +#endif + +// <q> Lock Bypass +// <i> Indicates whether Lock Bypass is enabled or not +// <id> fdpll96m_arch_lbypass +#ifndef CONF_DPLL_LBYPASS +#define CONF_DPLL_LBYPASS 0 +#endif + +// <o> Lock Time +// <0=>No time-out, automatic lock +// <4=>The Time-out if no lock within 8 ms +// <5=>The Time-out if no lock within 9 ms +// <6=>The Time-out if no lock within 10 ms +// <7=>The Time-out if no lock within 11 ms +// <id> fdpll96m_arch_ltime +#ifndef CONF_DPLL_LTIME +#define CONF_DPLL_LTIME 0 +#endif + +// <o> Reference Clock Selection +// <0=>XOSC32K clock reference +// <1=>XOSC clock reference +// <2=>GCLK clock reference +// <id> fdpll96m_arch_refclk +#ifndef CONF_DPLL_REFCLK +#define CONF_DPLL_REFCLK 0 +#endif + +// <q> Wake Up Fast +// <i> Indicates whether Wake Up Fast is enabled or not +// <id> fdpll96m_arch_wuf +#ifndef CONF_DPLL_WUF +#define CONF_DPLL_WUF 0 +#endif + +// <q> Low-Power Enable +// <i> Indicates whether Low-Power Enable is enabled or not +// <id> fdpll96m_arch_lpen +#ifndef CONF_DPLL_LPEN +#define CONF_DPLL_LPEN 0 +#endif + +// <o> Reference Clock Selection +// <0=>Default filter mode +// <1=>Low bandwidth filter +// <2=>High bandwidth filter +// <3=>High damping filter +// <id> fdpll96m_arch_filter +#ifndef CONF_DPLL_FILTER +#define CONF_DPLL_FILTER 0 +#endif + +// <y> Output Clock Prescaler +// <OSCCTRL_DPLLPRESC_PRESC_DIV1_Val"> 1 +// <OSCCTRL_DPLLPRESC_PRESC_DIV2_Val"> 2 +// <OSCCTRL_DPLLPRESC_PRESC_DIV4_Val"> 4 +// <id> fdpll96m_presc +#ifndef CONF_DPLL_PRESC +#define CONF_DPLL_PRESC OSCCTRL_DPLLPRESC_PRESC_DIV1_Val +#endif +//</h> +//</e> + +// <<< end of configuration section >>> + +#endif // HPL_OSCCTRL_CONFIG_H diff --git a/watch-library/shared/config/hpl_port_config.h b/watch-library/shared/config/hpl_port_config.h new file mode 100644 index 00000000..1efce33e --- /dev/null +++ b/watch-library/shared/config/hpl_port_config.h @@ -0,0 +1,284 @@ +/* Auto-generated config file hpl_port_config.h */ +#ifndef HPL_PORT_CONFIG_H +#define HPL_PORT_CONFIG_H + +// <<< Use Configuration Wizard in Context Menu >>> + +// <e> PORT Input Event 0 configuration +// <id> enable_port_input_event_0 +#ifndef CONF_PORT_EVCTRL_PORT_0 +#define CONF_PORT_EVCTRL_PORT_0 0 +#endif + +// <h> PORT Input Event 0 configuration on PORT A + +// <q> PORTA Input Event 0 Enable +// <i> The event action will be triggered on any incoming event if PORT A Input Event 0 configuration is enabled +// <id> porta_input_event_enable_0 +#ifndef CONF_PORTA_EVCTRL_PORTEI_0 +#define CONF_PORTA_EVCTRL_PORTEI_0 0x0 +#endif + +// <o> PORTA Event 0 Pin Identifier <0x00-0x1F> +// <i> These bits define the I/O pin from port A on which the event action will be performed +// <id> porta_event_pin_identifier_0 +#ifndef CONF_PORTA_EVCTRL_PID_0 +#define CONF_PORTA_EVCTRL_PID_0 0x0 +#endif + +// <o> PORTA Event 0 Action +// <0=> Output register of pin will be set to level of event +// <1=> Set output register of pin on event +// <2=> Clear output register of pin on event +// <3=> Toggle output register of pin on event +// <i> These bits define the event action the PORT A will perform on event input 0 +// <id> porta_event_action_0 +#ifndef CONF_PORTA_EVCTRL_EVACT_0 +#define CONF_PORTA_EVCTRL_EVACT_0 0 +#endif + +// </h> +// <h> PORT Input Event 0 configuration on PORT B + +// <q> PORTB Input Event 0 Enable +// <i> The event action will be triggered on any incoming event if PORT B Input Event 0 configuration is enabled +// <id> portb_input_event_enable_0 +#ifndef CONF_PORTB_EVCTRL_PORTEI_0 +#define CONF_PORTB_EVCTRL_PORTEI_0 0x0 +#endif + +// <o> PORTB Event 0 Pin Identifier <0x00-0x1F> +// <i> These bits define the I/O pin from port B on which the event action will be performed +// <id> portb_event_pin_identifier_0 +#ifndef CONF_PORTB_EVCTRL_PID_0 +#define CONF_PORTB_EVCTRL_PID_0 0x0 +#endif + +// <o> PORTB Event 0 Action +// <0=> Output register of pin will be set to level of event +// <1=> Set output register of pin on event +// <2=> Clear output register of pin on event +// <3=> Toggle output register of pin on event +// <i> These bits define the event action the PORT B will perform on event input 0 +// <id> portb_event_action_0 +#ifndef CONF_PORTB_EVCTRL_EVACT_0 +#define CONF_PORTB_EVCTRL_EVACT_0 0 +#endif + +// </h> + +// </e> + +// <e> PORT Input Event 1 configuration +// <id> enable_port_input_event_1 +#ifndef CONF_PORT_EVCTRL_PORT_1 +#define CONF_PORT_EVCTRL_PORT_1 0 +#endif + +// <h> PORT Input Event 1 configuration on PORT A + +// <q> PORTA Input Event 1 Enable +// <i> The event action will be triggered on any incoming event if PORT A Input Event 1 configuration is enabled +// <id> porta_input_event_enable_1 +#ifndef CONF_PORTA_EVCTRL_PORTEI_1 +#define CONF_PORTA_EVCTRL_PORTEI_1 0x0 +#endif + +// <o> PORTA Event 1 Pin Identifier <0x00-0x1F> +// <i> These bits define the I/O pin from port A on which the event action will be performed +// <id> porta_event_pin_identifier_1 +#ifndef CONF_PORTA_EVCTRL_PID_1 +#define CONF_PORTA_EVCTRL_PID_1 0x0 +#endif + +// <o> PORTA Event 1 Action +// <0=> Output register of pin will be set to level of event +// <1=> Set output register of pin on event +// <2=> Clear output register of pin on event +// <3=> Toggle output register of pin on event +// <i> These bits define the event action the PORT A will perform on event input 1 +// <id> porta_event_action_1 +#ifndef CONF_PORTA_EVCTRL_EVACT_1 +#define CONF_PORTA_EVCTRL_EVACT_1 0 +#endif + +// </h> +// <h> PORT Input Event 1 configuration on PORT B + +// <q> PORTB Input Event 1 Enable +// <i> The event action will be triggered on any incoming event if PORT B Input Event 1 configuration is enabled +// <id> portb_input_event_enable_1 +#ifndef CONF_PORTB_EVCTRL_PORTEI_1 +#define CONF_PORTB_EVCTRL_PORTEI_1 0x0 +#endif + +// <o> PORTB Event 1 Pin Identifier <0x00-0x1F> +// <i> These bits define the I/O pin from port B on which the event action will be performed +// <id> portb_event_pin_identifier_1 +#ifndef CONF_PORTB_EVCTRL_PID_1 +#define CONF_PORTB_EVCTRL_PID_1 0x0 +#endif + +// <o> PORTB Event 1 Action +// <0=> Output register of pin will be set to level of event +// <1=> Set output register of pin on event +// <2=> Clear output register of pin on event +// <3=> Toggle output register of pin on event +// <i> These bits define the event action the PORT B will perform on event input 1 +// <id> portb_event_action_1 +#ifndef CONF_PORTB_EVCTRL_EVACT_1 +#define CONF_PORTB_EVCTRL_EVACT_1 0 +#endif + +// </h> + +// </e> + +// <e> PORT Input Event 2 configuration +// <id> enable_port_input_event_2 +#ifndef CONF_PORT_EVCTRL_PORT_2 +#define CONF_PORT_EVCTRL_PORT_2 0 +#endif + +// <h> PORT Input Event 2 configuration on PORT A + +// <q> PORTA Input Event 2 Enable +// <i> The event action will be triggered on any incoming event if PORT A Input Event 2 configuration is enabled +// <id> porta_input_event_enable_2 +#ifndef CONF_PORTA_EVCTRL_PORTEI_2 +#define CONF_PORTA_EVCTRL_PORTEI_2 0x0 +#endif + +// <o> PORTA Event 2 Pin Identifier <0x00-0x1F> +// <i> These bits define the I/O pin from port A on which the event action will be performed +// <id> porta_event_pin_identifier_2 +#ifndef CONF_PORTA_EVCTRL_PID_2 +#define CONF_PORTA_EVCTRL_PID_2 0x0 +#endif + +// <o> PORTA Event 2 Action +// <0=> Output register of pin will be set to level of event +// <1=> Set output register of pin on event +// <2=> Clear output register of pin on event +// <3=> Toggle output register of pin on event +// <i> These bits define the event action the PORT A will perform on event input 2 +// <id> porta_event_action_2 +#ifndef CONF_PORTA_EVCTRL_EVACT_2 +#define CONF_PORTA_EVCTRL_EVACT_2 0 +#endif + +// </h> +// <h> PORT Input Event 2 configuration on PORT B + +// <q> PORTB Input Event 2 Enable +// <i> The event action will be triggered on any incoming event if PORT B Input Event 2 configuration is enabled +// <id> portb_input_event_enable_2 +#ifndef CONF_PORTB_EVCTRL_PORTEI_2 +#define CONF_PORTB_EVCTRL_PORTEI_2 0x0 +#endif + +// <o> PORTB Event 2 Pin Identifier <0x00-0x1F> +// <i> These bits define the I/O pin from port B on which the event action will be performed +// <id> portb_event_pin_identifier_2 +#ifndef CONF_PORTB_EVCTRL_PID_2 +#define CONF_PORTB_EVCTRL_PID_2 0x0 +#endif + +// <o> PORTB Event 2 Action +// <0=> Output register of pin will be set to level of event +// <1=> Set output register of pin on event +// <2=> Clear output register of pin on event +// <3=> Toggle output register of pin on event +// <i> These bits define the event action the PORT B will perform on event input 2 +// <id> portb_event_action_2 +#ifndef CONF_PORTB_EVCTRL_EVACT_2 +#define CONF_PORTB_EVCTRL_EVACT_2 0 +#endif + +// </h> + +// </e> + +// <e> PORT Input Event 3 configuration +// <id> enable_port_input_event_3 +#ifndef CONF_PORT_EVCTRL_PORT_3 +#define CONF_PORT_EVCTRL_PORT_3 0 +#endif + +// <h> PORT Input Event 3 configuration on PORT A + +// <q> PORTA Input Event 3 Enable +// <i> The event action will be triggered on any incoming event if PORT A Input Event 3 configuration is enabled +// <id> porta_input_event_enable_3 +#ifndef CONF_PORTA_EVCTRL_PORTEI_3 +#define CONF_PORTA_EVCTRL_PORTEI_3 0x0 +#endif + +// <o> PORTA Event 3 Pin Identifier <0x00-0x1F> +// <i> These bits define the I/O pin from port A on which the event action will be performed +// <id> porta_event_pin_identifier_3 +#ifndef CONF_PORTA_EVCTRL_PID_3 +#define CONF_PORTA_EVCTRL_PID_3 0x0 +#endif + +// <o> PORTA Event 3 Action +// <0=> Output register of pin will be set to level of event +// <1=> Set output register of pin on event +// <2=> Clear output register of pin on event +// <3=> Toggle output register of pin on event +// <i> These bits define the event action the PORT A will perform on event input 3 +// <id> porta_event_action_3 +#ifndef CONF_PORTA_EVCTRL_EVACT_3 +#define CONF_PORTA_EVCTRL_EVACT_3 0 +#endif + +// </h> +// <h> PORT Input Event 3 configuration on PORT B + +// <q> PORTB Input Event 3 Enable +// <i> The event action will be triggered on any incoming event if PORT B Input Event 3 configuration is enabled +// <id> portb_input_event_enable_3 +#ifndef CONF_PORTB_EVCTRL_PORTEI_3 +#define CONF_PORTB_EVCTRL_PORTEI_3 0x0 +#endif + +// <o> PORTB Event 3 Pin Identifier <0x00-0x1F> +// <i> These bits define the I/O pin from port B on which the event action will be performed +// <id> portb_event_pin_identifier_3 +#ifndef CONF_PORTB_EVCTRL_PID_3 +#define CONF_PORTB_EVCTRL_PID_3 0x0 +#endif + +// <o> PORTB Event 3 Action +// <0=> Output register of pin will be set to level of event +// <1=> Set output register of pin on event +// <2=> Clear output register of pin on event +// <3=> Toggle output register of pin on event +// <i> These bits define the event action the PORT B will perform on event input 3 +// <id> portb_event_action_3 +#ifndef CONF_PORTB_EVCTRL_EVACT_3 +#define CONF_PORTB_EVCTRL_EVACT_3 0 +#endif + +// </h> + +// </e> + +#define CONF_PORTA_EVCTRL \ + (0 | PORT_EVCTRL_EVACT0(CONF_PORTA_EVCTRL_EVACT_0) | CONF_PORTA_EVCTRL_PORTEI_0 << PORT_EVCTRL_PORTEI0_Pos \ + | PORT_EVCTRL_PID0(CONF_PORTA_EVCTRL_PID_0) | PORT_EVCTRL_EVACT1(CONF_PORTA_EVCTRL_EVACT_1) \ + | CONF_PORTA_EVCTRL_PORTEI_1 << PORT_EVCTRL_PORTEI1_Pos | PORT_EVCTRL_PID1(CONF_PORTA_EVCTRL_PID_1) \ + | PORT_EVCTRL_EVACT2(CONF_PORTA_EVCTRL_EVACT_2) | CONF_PORTA_EVCTRL_PORTEI_2 << PORT_EVCTRL_PORTEI2_Pos \ + | PORT_EVCTRL_PID2(CONF_PORTA_EVCTRL_PID_2) | PORT_EVCTRL_EVACT3(CONF_PORTA_EVCTRL_EVACT_3) \ + | CONF_PORTA_EVCTRL_PORTEI_3 << PORT_EVCTRL_PORTEI3_Pos | PORT_EVCTRL_PID3(CONF_PORTA_EVCTRL_PID_3)) +#define CONF_PORTB_EVCTRL \ + (0 | PORT_EVCTRL_EVACT0(CONF_PORTB_EVCTRL_EVACT_0) | CONF_PORTB_EVCTRL_PORTEI_0 << PORT_EVCTRL_PORTEI0_Pos \ + | PORT_EVCTRL_PID0(CONF_PORTB_EVCTRL_PID_0) | PORT_EVCTRL_EVACT1(CONF_PORTB_EVCTRL_EVACT_1) \ + | CONF_PORTB_EVCTRL_PORTEI_1 << PORT_EVCTRL_PORTEI1_Pos | PORT_EVCTRL_PID1(CONF_PORTB_EVCTRL_PID_1) \ + | PORT_EVCTRL_EVACT2(CONF_PORTB_EVCTRL_EVACT_2) | CONF_PORTB_EVCTRL_PORTEI_2 << PORT_EVCTRL_PORTEI2_Pos \ + | PORT_EVCTRL_PID2(CONF_PORTB_EVCTRL_PID_2) | PORT_EVCTRL_EVACT3(CONF_PORTB_EVCTRL_EVACT_3) \ + | CONF_PORTB_EVCTRL_PORTEI_3 << PORT_EVCTRL_PORTEI3_Pos | PORT_EVCTRL_PID3(CONF_PORTB_EVCTRL_PID_3)) + +// <<< end of configuration section >>> + +#endif // HPL_PORT_CONFIG_H diff --git a/watch-library/shared/config/hpl_rtc_config.h b/watch-library/shared/config/hpl_rtc_config.h new file mode 100644 index 00000000..9085ca37 --- /dev/null +++ b/watch-library/shared/config/hpl_rtc_config.h @@ -0,0 +1,318 @@ +/* Auto-generated config file hpl_rtc_config.h */ +#ifndef HPL_RTC_CONFIG_H +#define HPL_RTC_CONFIG_H + +// <<< Use Configuration Wizard in Context Menu >>> + +// <h> Basic settings + +#ifndef CONF_RTC_ENABLE +#define CONF_RTC_ENABLE 1 +#endif + +// <q> Force reset RTC on initialization +// <i> Force RTC to reset on initialization. +// <i> Note that the previous power down data in RTC is lost if it's enabled. +// <id> rtc_arch_init_reset +#ifndef CONF_RTC_INIT_RESET +#define CONF_RTC_INIT_RESET 0 +#endif + +// <o> Prescaler configuration +// <0x0=>OFF(Peripheral clock divided by 1) +// <0x1=>Peripheral clock divided by 1 +// <0x2=>Peripheral clock divided by 2 +// <0x3=>Peripheral clock divided by 4 +// <0x4=>Peripheral clock divided by 8 +// <0x5=>Peripheral clock divided by 16 +// <0x6=>Peripheral clock divided by 32 +// <0x7=>Peripheral clock divided by 64 +// <0x8=>Peripheral clock divided by 128 +// <0x9=>Peripheral clock divided by 256 +// <0xA=>Peripheral clock divided by 512 +// <0xB=>Peripheral clock divided by 1024 +// <i> These bits define the RTC clock relative to the peripheral clock +// <id> rtc_arch_prescaler +#ifndef CONF_RTC_PRESCALER + +#define CONF_RTC_PRESCALER 0xb + +#endif + +#ifndef CONF_RTC_COMP_VAL + +#define CONF_RTC_COMP_VAL 0 + +#endif + +// <e> RTC Tamper Input 0 settings +// <id> tamper_input_0_settings +#ifndef CONF_TAMPER_INPUT_0_SETTINGS +#define CONF_TAMPER_INPUT_0_SETTINGS 0 +#endif + +// <q> Tamper Level Settings +// <i> Indicates Tamper input 0 level +// <id> tamper_level_0 +#ifndef CONF_RTC_TAMP_LVL_0 +#define CONF_RTC_TAMP_LVL_0 0 +#endif + +// <o> RTC Tamper Input Action +// <0x0=>OFF(Disabled) +// <0x1=>Wake and Set Tamper Flag +// <0x2=>Capture Timestamp and Set Tamper Flag +// <0x3=>Active Layer Mode.IN and OUT pin is used.Timestamp is also captured. +// <i> These bits define the RTC Tamper Input Action to be performed +// <id> rtc_tamper_input_action_0 +#ifndef CONF_RTC_TAMPER_INACT_0 +#define CONF_RTC_TAMPER_INACT_0 0 +#endif + +// <q> Debounce Enable for Tamper Input +// <i> Indicates Debounce should be enabled for Tamper input 0 +// <id> tamper_debounce_enable_0 +#ifndef CONF_RTC_TAMP_DEBNC_0 +#define CONF_RTC_TAMP_DEBNC_0 0 +#endif + +// </e> + +// <e> RTC Tamper Input 1 settings +// <id> tamper_input_1_settings +#ifndef CONF_TAMPER_INPUT_1_SETTINGS +#define CONF_TAMPER_INPUT_1_SETTINGS 0 +#endif + +// <q> Tamper Level Settings +// <i> Indicates Tamper input 1 level +// <id> tamper_level_1 +#ifndef CONF_RTC_TAMP_LVL_1 +#define CONF_RTC_TAMP_LVL_1 0 +#endif + +// <o> RTC Tamper Input Action +// <0x0=>OFF(Disabled) +// <0x1=>Wake and Set Tamper Flag +// <0x2=>Capture Timestamp and Set Tamper Flag +// <0x3=>Active Layer Mode.IN and OUT pin is used.Timestamp is also captured. +// <i> These bits define the RTC Tamper Input Action to be performed +// <id> rtc_tamper_input_action_1 +#ifndef CONF_RTC_TAMPER_INACT_1 +#define CONF_RTC_TAMPER_INACT_1 0 +#endif + +// <q> Debounce Enable for Tamper Input +// <i> Indicates Debounce should be enabled for Tamper input 1 +// <id> tamper_debounce_enable_1 +#ifndef CONF_RTC_TAMP_DEBNC_1 +#define CONF_RTC_TAMP_DEBNC_1 0 +#endif + +// </e> + +// <e> RTC Tamper Input 2 settings +// <id> tamper_input_2_settings +#ifndef CONF_TAMPER_INPUT_2_SETTINGS +#define CONF_TAMPER_INPUT_2_SETTINGS 0 +#endif + +// <q> Tamper Level Settings +// <i> Indicates Tamper input 2 level +// <id> tamper_level_2 +#ifndef CONF_RTC_TAMP_LVL_2 +#define CONF_RTC_TAMP_LVL_2 0 +#endif + +// <o> RTC Tamper Input Action +// <0x0=>OFF(Disabled) +// <0x1=>Wake and Set Tamper Flag +// <0x2=>Capture Timestamp and Set Tamper Flag +// <0x3=>Active Layer Mode.IN and OUT pin is used.Timestamp is also captured. +// <i> These bits define the RTC Tamper Input Action to be performed +// <id> rtc_tamper_input_action_2 +#ifndef CONF_RTC_TAMPER_INACT_2 +#define CONF_RTC_TAMPER_INACT_2 0 +#endif + +// <q> Debounce Enable for Tamper Input +// <i> Indicates Debounce should be enabled for Tamper input 2 +// <id> tamper_debounce_enable_2 +#ifndef CONF_RTC_TAMP_DEBNC_2 +#define CONF_RTC_TAMP_DEBNC_2 0 +#endif + +// </e> + +// <e> RTC Tamper Input 3 settings +// <id> tamper_input_3_settings +#ifndef CONF_TAMPER_INPUT_3_SETTINGS +#define CONF_TAMPER_INPUT_3_SETTINGS 0 +#endif + +// <q> Tamper Level Settings +// <i> Indicates Tamper input 3 level +// <id> tamper_level_3 +#ifndef CONF_RTC_TAMP_LVL_3 +#define CONF_RTC_TAMP_LVL_3 0 +#endif + +// <o> RTC Tamper Input Action +// <0x0=>OFF(Disabled) +// <0x1=>Wake and Set Tamper Flag +// <0x2=>Capture Timestamp and Set Tamper Flag +// <0x3=>Active Layer Mode.IN and OUT pin is used.Timestamp is also captured. +// <i> These bits define the RTC Tamper Input Action to be performed +// <id> rtc_tamper_input_action_3 +#ifndef CONF_RTC_TAMPER_INACT_3 +#define CONF_RTC_TAMPER_INACT_3 0 +#endif + +// <q> Debounce Enable for Tamper Input +// <i> Indicates Debounce should be enabled for Tamper input 3 +// <id> tamper_debounce_enable_3 +#ifndef CONF_RTC_TAMP_DEBNC_3 +#define CONF_RTC_TAMP_DEBNC_3 0 +#endif + +// </e> + +// <e> RTC Tamper Input 4 settings +// <id> tamper_input_4_settings +#ifndef CONF_TAMPER_INPUT_4_SETTINGS +#define CONF_TAMPER_INPUT_4_SETTINGS 0 +#endif + +// <q> Tamper Level Settings +// <i> Indicates Tamper input 4 level +// <id> tamper_level_4 +#ifndef CONF_RTC_TAMP_LVL_4 +#define CONF_RTC_TAMP_LVL_4 0 +#endif + +// <o> RTC Tamper Input Action +// <0x0=>OFF(Disabled) +// <0x1=>Wake and Set Tamper Flag +// <0x2=>Capture Timestamp and Set Tamper Flag +// <0x3=>Active Layer Mode.IN and OUT pin is used.Timestamp is also captured. +// <i> These bits define the RTC Tamper Input Action to be performed +// <id> rtc_tamper_input_action_4 +#ifndef CONF_RTC_TAMPER_INACT_4 +#define CONF_RTC_TAMPER_INACT_4 0 +#endif + +// <q> Debounce Enable for Tamper Input +// <i> Indicates Debounce should be enabled for Tamper input 4 +// <id> tamper_debounce_enable_4 +#ifndef CONF_RTC_TAMP_DEBNC_4 +#define CONF_RTC_TAMP_DEBNC_4 0 +#endif + +// </e> + +// <o> RTC Tamper Active Layer Frequency Prescalar +// <0x0=>DIV2 CLK_RTC_OUT is CLK_RTC /2 +// <0x1=>DIV4 CLK_RTC_OUT is CLK_RTC /4 +// <0x2=>DIV8 CLK_RTC_OUT is CLK_RTC /8 +// <0x3=>DIV16 CLK_RTC_OUT is CLK_RTC /16 +// <0x4=>DIV32 CLK_RTC_OUT is CLK_RTC /32 +// <0x5=>DIV64 CLK_RTC_OUT is CLK_RTC /64 +// <0x6=>DIV128 CLK_RTC_OUT is CLK_RTC /128 +// <0x7=>DIV256 CLK_RTC_OUT is CLK_RTC /256 +// <i> These bits define the RTC Tamper Active Layer Frequecny Prescalar +// <id> rtc_tamper_active_layer_frequency_prescalar +#ifndef CONF_RTC_TAMP_ACT_LAYER_FREQ_PRES +#define CONF_RTC_TAMP_ACT_LAYER_FREQ_PRES 0 +#endif + +// <o> RTC Tamper Debounce Frequency Prescalar +// <0x0=>DIV2 CLK_RTC_DEB is CLK_RTC /2 +// <0x1=>DIV4 CLK_RTC_DEB is CLK_RTC /4 +// <0x2=>DIV8 CLK_RTC_DEB is CLK_RTC /8 +// <0x3=>DIV16 CLK_RTC_DEB is CLK_RTC /16 +// <0x4=>DIV32 CLK_RTC_DEB is CLK_RTC /32 +// <0x5=>DIV64 CLK_RTC_DEB is CLK_RTC /64 +// <0x6=>DIV128 CLK_RTC_DEB is CLK_RTC /128 +// <0x7=>DIV256 CLK_RTC_DEB is CLK_RTC /256 +// <i> These bits define the RTC Debounce Frequency Prescalar +// <id> rtc_tamper_debounce_frequency_prescalar +#ifndef CONF_RTC_TAMP_DEBF_PRES +#define CONF_RTC_TAMP_DEBF_PRES 0 +#endif + +// <e> Event control +// <id> rtc_event_control +#ifndef CONF_RTC_EVENT_CONTROL_ENABLE +#define CONF_RTC_EVENT_CONTROL_ENABLE 0 +#endif + +// <q> Periodic Interval 0 Event Output +// <i> This bit indicates whether Periodic interval 0 event is enabled and will be generated +// <id> rtc_pereo0 +#ifndef CONF_RTC_PEREO0 +#define CONF_RTC_PEREO0 0 +#endif +// <q> Periodic Interval 1 Event Output +// <i> This bit indicates whether Periodic interval 1 event is enabled and will be generated +// <id> rtc_pereo1 +#ifndef CONF_RTC_PEREO1 +#define CONF_RTC_PEREO1 0 +#endif +// <q> Periodic Interval 2 Event Output +// <i> This bit indicates whether Periodic interval 2 event is enabled and will be generated +// <id> rtc_pereo2 +#ifndef CONF_RTC_PEREO2 +#define CONF_RTC_PEREO2 0 +#endif +// <q> Periodic Interval 3 Event Output +// <i> This bit indicates whether Periodic interval 3 event is enabled and will be generated +// <id> rtc_pereo3 +#ifndef CONF_RTC_PEREO3 +#define CONF_RTC_PEREO3 0 +#endif +// <q> Periodic Interval 4 Event Output +// <i> This bit indicates whether Periodic interval 4 event is enabled and will be generated +// <id> rtc_pereo4 +#ifndef CONF_RTC_PEREO4 +#define CONF_RTC_PEREO4 0 +#endif +// <q> Periodic Interval 5 Event Output +// <i> This bit indicates whether Periodic interval 5 event is enabled and will be generated +// <id> rtc_pereo5 +#ifndef CONF_RTC_PEREO5 +#define CONF_RTC_PEREO5 0 +#endif +// <q> Periodic Interval 6 Event Output +// <i> This bit indicates whether Periodic interval 6 event is enabled and will be generated +// <id> rtc_pereo6 +#ifndef CONF_RTC_PEREO6 +#define CONF_RTC_PEREO6 0 +#endif +// <q> Periodic Interval 7 Event Output +// <i> This bit indicates whether Periodic interval 7 event is enabled and will be generated +// <id> rtc_pereo7 +#ifndef CONF_RTC_PEREO7 +#define CONF_RTC_PEREO7 0 +#endif + +// <q> Compare 0 Event Output +// <i> This bit indicates whether Compare O event is enabled and will be generated +// <id> rtc_cmpeo0 +#ifndef CONF_RTC_COMPE0 +#define CONF_RTC_COMPE0 0 +#endif + +// <q> Overflow Event Output +// <i> This bit indicates whether Overflow event is enabled and will be generated +// <id> rtc_ovfeo +#ifndef CONF_RTC_OVFEO +#define CONF_RTC_OVFEO 0 +#endif + +// </e> + +// </h> + +// <<< end of configuration section >>> + +#endif // HPL_RTC_CONFIG_H diff --git a/watch-library/shared/config/hpl_sercom_config.h b/watch-library/shared/config/hpl_sercom_config.h new file mode 100644 index 00000000..6df4b08e --- /dev/null +++ b/watch-library/shared/config/hpl_sercom_config.h @@ -0,0 +1,303 @@ +/* Auto-generated config file hpl_sercom_config.h */ +#ifndef HPL_SERCOM_CONFIG_H +#define HPL_SERCOM_CONFIG_H + +// <<< Use Configuration Wizard in Context Menu >>> + +#include <peripheral_clk_config.h> + +#ifndef SERCOM_I2CM_CTRLA_MODE_I2C_MASTER +#define SERCOM_I2CM_CTRLA_MODE_I2C_MASTER (5 << 2) +#endif + +#ifndef CONF_SERCOM_1_I2CM_ENABLE +#define CONF_SERCOM_1_I2CM_ENABLE 1 +#endif + +// <h> Basic + +// <o> I2C Bus clock speed (Hz) <1-400000> +// <i> I2C Bus clock (SCL) speed measured in Hz +// <id> i2c_master_baud_rate +#ifndef CONF_SERCOM_1_I2CM_BAUD +#define CONF_SERCOM_1_I2CM_BAUD 100000 +#endif + +// </h> + +// <e> Advanced +// <id> i2c_master_advanced +#ifndef CONF_SERCOM_1_I2CM_ADVANCED_CONFIG +#define CONF_SERCOM_1_I2CM_ADVANCED_CONFIG 0 +#endif + +// <o> TRise (ns) <0-300> +// <i> Determined by the bus impedance, check electric characteristics in the datasheet +// <i> Standard Fast Mode: typical 215ns, max 300ns +// <i> Fast Mode +: typical 60ns, max 100ns +// <i> High Speed Mode: typical 20ns, max 40ns +// <id> i2c_master_arch_trise + +#ifndef CONF_SERCOM_1_I2CM_TRISE +#define CONF_SERCOM_1_I2CM_TRISE 215 +#endif + +// <q> Master SCL Low Extended Time-Out (MEXTTOEN) +// <i> This enables the master SCL low extend time-out +// <id> i2c_master_arch_mexttoen +#ifndef CONF_SERCOM_1_I2CM_MEXTTOEN +#define CONF_SERCOM_1_I2CM_MEXTTOEN 0 +#endif + +// <q> Slave SCL Low Extend Time-Out (SEXTTOEN) +// <i> Enables the slave SCL low extend time-out. If SCL is cumulatively held low for greater than 25ms from the initial START to a STOP, the slave will release its clock hold if enabled and reset the internal state machine +// <id> i2c_master_arch_sexttoen +#ifndef CONF_SERCOM_1_I2CM_SEXTTOEN +#define CONF_SERCOM_1_I2CM_SEXTTOEN 0 +#endif + +// <q> SCL Low Time-Out (LOWTOUT) +// <i> Enables SCL low time-out. If SCL is held low for 25ms-35ms, the master will release it's clock hold +// <id> i2c_master_arch_lowtout +#ifndef CONF_SERCOM_1_I2CM_LOWTOUT +#define CONF_SERCOM_1_I2CM_LOWTOUT 0 +#endif + +// <o> Inactive Time-Out (INACTOUT) +// <0x0=>Disabled +// <0x1=>5-6 SCL cycle time-out(50-60us) +// <0x2=>10-11 SCL cycle time-out(100-110us) +// <0x3=>20-21 SCL cycle time-out(200-210us) +// <i> Defines if inactivity time-out should be enabled, and how long the time-out should be +// <id> i2c_master_arch_inactout +#ifndef CONF_SERCOM_1_I2CM_INACTOUT +#define CONF_SERCOM_1_I2CM_INACTOUT 0x0 +#endif + +// <o> SDA Hold Time (SDAHOLD) +// <0=>Disabled +// <1=>50-100ns hold time +// <2=>300-600ns hold time +// <3=>400-800ns hold time +// <i> Defines the SDA hold time with respect to the negative edge of SCL +// <id> i2c_master_arch_sdahold +#ifndef CONF_SERCOM_1_I2CM_SDAHOLD +#define CONF_SERCOM_1_I2CM_SDAHOLD 0x2 +#endif + +// <q> Run in stand-by +// <i> Determine if the module shall run in standby sleep mode +// <id> i2c_master_arch_runstdby +#ifndef CONF_SERCOM_1_I2CM_RUNSTDBY +#define CONF_SERCOM_1_I2CM_RUNSTDBY 0 +#endif + +// <o> Debug Stop Mode +// <i> Behavior of the baud-rate generator when CPU is halted by external debugger. +// <0=>Keep running +// <1=>Halt +// <id> i2c_master_arch_dbgstop +#ifndef CONF_SERCOM_1_I2CM_DEBUG_STOP_MODE +#define CONF_SERCOM_1_I2CM_DEBUG_STOP_MODE 0 +#endif + +// </e> + +#ifndef CONF_SERCOM_1_I2CM_SPEED +#define CONF_SERCOM_1_I2CM_SPEED 0x00 // Speed: Standard/Fast mode +#endif +#if CONF_SERCOM_1_I2CM_TRISE < 215 || CONF_SERCOM_1_I2CM_TRISE > 300 +#warning Bad I2C Rise time for Standard/Fast mode, reset to 215ns +#undef CONF_SERCOM_1_I2CM_TRISE +#define CONF_SERCOM_1_I2CM_TRISE 215U +#endif + +// gclk_freq - (i2c_scl_freq * 10) - (gclk_freq * i2c_scl_freq * Trise) +// BAUD + BAUDLOW = -------------------------------------------------------------------- +// i2c_scl_freq +// BAUD: register value low [7:0] +// BAUDLOW: register value high [15:8], only used for odd BAUD + BAUDLOW +#define CONF_SERCOM_1_I2CM_BAUD_BAUDLOW \ + (((CONF_GCLK_SERCOM1_CORE_FREQUENCY - (CONF_SERCOM_1_I2CM_BAUD * 10U) \ + - (CONF_SERCOM_1_I2CM_TRISE * (CONF_SERCOM_1_I2CM_BAUD / 100U) * (CONF_GCLK_SERCOM1_CORE_FREQUENCY / 10000U) \ + / 1000U)) \ + * 10U \ + + 5U) \ + / (CONF_SERCOM_1_I2CM_BAUD * 10U)) +#ifndef CONF_SERCOM_1_I2CM_BAUD_RATE +#if CONF_SERCOM_1_I2CM_BAUD_BAUDLOW > (0xFF * 2) +#warning Requested I2C baudrate too low, please check +#define CONF_SERCOM_1_I2CM_BAUD_RATE 0xFF +#elif CONF_SERCOM_1_I2CM_BAUD_BAUDLOW <= 1 +#warning Requested I2C baudrate too high, please check +#define CONF_SERCOM_1_I2CM_BAUD_RATE 1 +#else +#define CONF_SERCOM_1_I2CM_BAUD_RATE \ + ((CONF_SERCOM_1_I2CM_BAUD_BAUDLOW & 0x1) \ + ? (CONF_SERCOM_1_I2CM_BAUD_BAUDLOW / 2) + ((CONF_SERCOM_1_I2CM_BAUD_BAUDLOW / 2 + 1) << 8) \ + : (CONF_SERCOM_1_I2CM_BAUD_BAUDLOW / 2)) +#endif +#endif + +#include <peripheral_clk_config.h> + +// Enable configuration of module +#ifndef CONF_SERCOM_3_SPI_ENABLE +#define CONF_SERCOM_3_SPI_ENABLE 1 +#endif + +// Set module in SPI Master mode +#ifndef CONF_SERCOM_3_SPI_MODE +#define CONF_SERCOM_3_SPI_MODE 0x03 +#endif + +// <h> Basic Configuration + +// <q> Receive buffer enable +// <i> Enable receive buffer to receive data from slave (RXEN) +// <id> spi_master_rx_enable +#ifndef CONF_SERCOM_3_SPI_RXEN +#define CONF_SERCOM_3_SPI_RXEN 0x1 +#endif + +// <o> Character Size +// <i> Bit size for all characters sent over the SPI bus (CHSIZE) +// <0x0=>8 bits +// <0x1=>9 bits +// <id> spi_master_character_size +#ifndef CONF_SERCOM_3_SPI_CHSIZE +#define CONF_SERCOM_3_SPI_CHSIZE 0x0 +#endif +// <o> Baud rate <1-12000000> +// <i> The SPI data transfer rate +// <id> spi_master_baud_rate +#ifndef CONF_SERCOM_3_SPI_BAUD +#define CONF_SERCOM_3_SPI_BAUD 50000 +#endif + +// </h> + +// <e> Advanced Configuration +// <id> spi_master_advanced +#ifndef CONF_SERCOM_3_SPI_ADVANCED +#define CONF_SERCOM_3_SPI_ADVANCED 1 +#endif + +// <o> Dummy byte <0x00-0x1ff> +// <id> spi_master_dummybyte +// <i> Dummy byte used when reading data from the slave without sending any data +#ifndef CONF_SERCOM_3_SPI_DUMMYBYTE +#define CONF_SERCOM_3_SPI_DUMMYBYTE 0x1ff +#endif + +// <o> Data Order +// <0=>MSB first +// <1=>LSB first +// <i> I least significant or most significant bit is shifted out first (DORD) +// <id> spi_master_arch_dord +#ifndef CONF_SERCOM_3_SPI_DORD +#define CONF_SERCOM_3_SPI_DORD 0x0 +#endif + +// <o> Clock Polarity +// <0=>SCK is low when idle +// <1=>SCK is high when idle +// <i> Determines if the leading edge is rising or falling with a corresponding opposite edge at the trailing edge. (CPOL) +// <id> spi_master_arch_cpol +#ifndef CONF_SERCOM_3_SPI_CPOL +#define CONF_SERCOM_3_SPI_CPOL 0x0 +#endif + +// <o> Clock Phase +// <0x0=>Sample input on leading edge +// <0x1=>Sample input on trailing edge +// <i> Determines if input data is sampled on leading or trailing SCK edge. (CPHA) +// <id> spi_master_arch_cpha +#ifndef CONF_SERCOM_3_SPI_CPHA +#define CONF_SERCOM_3_SPI_CPHA 0x0 +#endif + +// <o> Immediate Buffer Overflow Notification +// <i> Controls when OVF is asserted (IBON) +// <0x0=>In data stream +// <0x1=>On buffer overflow +// <id> spi_master_arch_ibon +#ifndef CONF_SERCOM_3_SPI_IBON +#define CONF_SERCOM_3_SPI_IBON 0x0 +#endif + +// <q> Run in stand-by +// <i> Module stays active in stand-by sleep mode. (RUNSTDBY) +// <id> spi_master_arch_runstdby +#ifndef CONF_SERCOM_3_SPI_RUNSTDBY +#define CONF_SERCOM_3_SPI_RUNSTDBY 0x0 +#endif + +// <o> Debug Stop Mode +// <i> Behavior of the baud-rate generator when CPU is halted by external debugger. (DBGSTOP) +// <0=>Keep running +// <1=>Halt +// <id> spi_master_arch_dbgstop +#ifndef CONF_SERCOM_3_SPI_DBGSTOP +#define CONF_SERCOM_3_SPI_DBGSTOP 0 +#endif + +// </e> + +// Address mode disabled in master mode +#ifndef CONF_SERCOM_3_SPI_AMODE_EN +#define CONF_SERCOM_3_SPI_AMODE_EN 0 +#endif + +#ifndef CONF_SERCOM_3_SPI_AMODE +#define CONF_SERCOM_3_SPI_AMODE 0 +#endif + +#ifndef CONF_SERCOM_3_SPI_ADDR +#define CONF_SERCOM_3_SPI_ADDR 0 +#endif + +#ifndef CONF_SERCOM_3_SPI_ADDRMASK +#define CONF_SERCOM_3_SPI_ADDRMASK 0 +#endif + +#ifndef CONF_SERCOM_3_SPI_SSDE +#define CONF_SERCOM_3_SPI_SSDE 0 +#endif + +#ifndef CONF_SERCOM_3_SPI_MSSEN +#define CONF_SERCOM_3_SPI_MSSEN 0x0 +#endif + +#ifndef CONF_SERCOM_3_SPI_PLOADEN +#define CONF_SERCOM_3_SPI_PLOADEN 0 +#endif + +// <o> Receive Data Pinout +// <0x0=>PAD[0] +// <0x1=>PAD[1] +// <0x2=>PAD[2] +// <0x3=>PAD[3] +// <id> spi_master_rxpo +#ifndef CONF_SERCOM_3_SPI_RXPO +#define CONF_SERCOM_3_SPI_RXPO 2 +#endif + +// <o> Transmit Data Pinout +// <0x0=>PAD[0,1]_DO_SCK +// <0x1=>PAD[2,3]_DO_SCK +// <0x2=>PAD[3,1]_DO_SCK +// <0x3=>PAD[0,3]_DO_SCK +// <id> spi_master_txpo +#ifndef CONF_SERCOM_3_SPI_TXPO +#define CONF_SERCOM_3_SPI_TXPO 3 +#endif + +// Calculate baud register value from requested baudrate value +#ifndef CONF_SERCOM_3_SPI_BAUD_RATE +#define CONF_SERCOM_3_SPI_BAUD_RATE ((float)CONF_GCLK_SERCOM3_CORE_FREQUENCY / (float)(2 * CONF_SERCOM_3_SPI_BAUD)) - 1 +#endif + +// <<< end of configuration section >>> + +#endif // HPL_SERCOM_CONFIG_H diff --git a/watch-library/shared/config/hpl_slcd_config.h b/watch-library/shared/config/hpl_slcd_config.h new file mode 100644 index 00000000..d78e3391 --- /dev/null +++ b/watch-library/shared/config/hpl_slcd_config.h @@ -0,0 +1,239 @@ +/* Auto-generated config file hpl_slcd_config.h */ +#ifndef HPL_SLCD_CONFIG_H +#define HPL_SLCD_CONFIG_H + +// <<< Use Configuration Wizard in Context Menu >>> + +#include <hpl_slcd_cm.h> +#include <peripheral_clk_config.h> +#include "pins.h" + +// <h> Standard configuration + +// <o> Number of COM Lines +// <i> Number of COM Lines +// <0=>1 +// <1=>2 +// <2=>3 +// <3=>4 +// <4=>6 +// <5=>8 +// <id> slcd_arch_com_num +#ifndef CONF_SLCD_COM_NUM +#define CONF_SLCD_COM_NUM 2 +#endif + +// <o> Number of Segment Lines <1-44> +// <i> Number of Segment Lines +// <id> slcd_arch_seg_num +#ifndef CONF_SLCD_SEG_NUM +#define CONF_SLCD_SEG_NUM 24 +#endif + +#if CONF_SLCD_COM_NUM == SLCD_CTRLA_DUTY_SIXTH_Val && CONF_SLCD_SEG_NUM > 42 +#warning Segment number should less than or equals to 42 +#endif +#if CONF_SLCD_COM_NUM == SLCD_CTRLA_DUTY_EIGHT_Val && CONF_SLCD_SEG_NUM > 40 +#warning Segment number should less than or equals to 40 +#endif + +// <o> Bias +// <i> Bias Settting +// <0=>STATIC +// <1=>HALF +// <2=>THIRD +// <3=>FOURTH +// <id> slcd_arch_bias +#ifndef CONF_SLCD_BIAS +#define CONF_SLCD_BIAS 2 +#endif + +#if CONF_SLCD_COM_NUM == 0 && CONF_SLCD_BIAS != 0 +#warning Recommended Bias for 1 common terminal is STATIC +#elif CONF_SLCD_COM_NUM == 1 && CONF_SLCD_BIAS != 1 +#warning Recommended Bias for 2 Common Terminals is HALF +#elif CONF_SLCD_COM_NUM <= 4 && CONF_SLCD_BIAS != 2 +#warning Recommended Bias for 3/4/6 Common Terminals is THIRD +#elif CONF_SLCD_COM_NUM == 5 && CONF_SLCD_BIAS != 3 +#warning Recommended Bias for 8 Common Terminals is FOURTH +#endif + +// <q> Bias Buffer Enable +// <i> Enable Bias Buffer +// <id> slcd_arch_bben +#ifndef CONF_SLCD_BBEN +#define CONF_SLCD_BBEN 1 +#endif + +// <o> Bias Buffer Enable Duration <1-16> +// <i> Configure the enable duration of the bias buffer, unit is cycle of SLCD OSC clock source +// <id> slcd_arch_bbd +#ifndef CONF_SLCD_BBD +#define CONF_SLCD_BBD 2 +#endif + +// <o> Clock Prescaler +// <i> Setting for LCD frame frequency +// <0=>16 +// <1=>32 +// <2=>64 +// <3=>128 +// <id> slcd_arch_presc +#ifndef CONF_SLCD_PRESC +#define CONF_SLCD_PRESC 1 +#endif + +// <o> Clock Divider +// <i> Setting for LCD frame frequency +// <0=>1 +// <1=>2 +// <2=>3 +// <3=>4 +// <4=>5 +// <5=>6 +// <6=>7 +// <7=>8 +// <id> slcd_arch_ckdiv +#ifndef CONF_SLCD_CKDIV +#define CONF_SLCD_CKDIV 5 +#endif + +/* TODO add frame frequency check */ + +// <o> Reference Refresh Frequency +// <i> Setting for Reference Refresh Frequency +// <0=>2kHz +// <1=>1kHz +// <2=>500Hz +// <3=>250Hz +// <4=>125Hz +// <5=>62.5Hz +// <id> slcd_arch_rrf +#ifndef CONF_SLCD_RRF +#define CONF_SLCD_RRF 0 +#endif + +// <o> Power Refresh Frequency +// <i> Setting for Charge pump Refresh Frequency +// <0=>2kHz +// <1=>1kHz +// <2=>500Hz +// <3=>250Hz +// <id> slcd_arch_prf +#ifndef CONF_SLCD_PRF +#define CONF_SLCD_PRF 3 +#endif + +// <q> External VLCD +// <i> Setting for how VLCD is generated +// <id> slcd_arch_xvlcd +#ifndef CONF_SLCD_XVLCD +#define CONF_SLCD_XVLCD 0 +#endif + +// <o> Waveform Mode +// <i> Setting for Waveform Mode +// <0=>Low Power Waveform(frame-inversion) +// <1=>Standard Waveform Mode(bit-inversion) +// <id> slcd_arch_wmod +#ifndef CONF_SLCD_WMOD +#define CONF_SLCD_WMOD 0 +#endif + +// <o> Contrast Adjustment +// <i> The contrast of the LCD is determined by the value of VLCD voltage. +// <i> The higher the VLCD voltage, the higher is the contrast. +// <i> The software contrast adjustment is only possible in internal supply mode. +// <0=>2.5056V +// <1=>2.5731V +// <2=>2.6379V +// <3=>2.7054V +// <4=>2.7729V +// <5=>2.8404V +// <6=>2.9052V +// <7=>2.9727V +// <8=>3.0402V +// <9=>3.1077V +// <10=>3.1725V +// <11=>3.24V +// <12=>3.3075V +// <13=>3.375V +// <14=>3.4398V +// <15=>3.5073V +// <id> slcd_arch_contrast_adjust +#ifndef CONF_SLCD_CONTRAST_ADJUST +#define CONF_SLCD_CONTRAST_ADJUST 14 +#endif + +// </h> + +// <e> Advanced configuration +// <id> slcd_arch_advanced_settings +#ifndef CONF_SLCD_ADVANCED_SETTINGS +#define CONF_SLCD_ADVANCED_SETTINGS 1 +#endif + +// <q> Run in standby +// <i> Indicates whether the SLCD will continue running in standby sleep mode or not +// <id> slcd_arch_runstdby +#ifndef CONF_SLCD_RUNSTDBY +#define CONF_SLCD_RUNSTDBY 1 +#endif + +// </e> + +#if SLCD_FRAME_FREQUENCY < 30 || SLCD_FRAME_FREQUENCY > 100 +#warning The optimal frame frequency should be in range from 30Hz up to 100Hz to avoid flickering and ghosting effect. +#endif + +#define SLCD_FC_MAX_MS (((0x1F + 1) * 8) * (1000 / SLCD_FRAME_FREQUENCY)) +#define SLCD_FC_MIN_MS (1000 / SLCD_FRAME_FREQUENCY) +#define SLCD_FC_BYPASS_MAX_MS ((0x1F + 1) * (1000 / SLCD_FRAME_FREQUENCY)) + +// <e> Character Mapping Setting +// <id> slcd_arch_cm_setting +#ifndef CONF_SLCD_CM_ENABLE +#define CONF_SLCD_CM_ENABLE 0 +#endif + +/** + * character lookup table + */ +#ifndef CONF_SLCD_LPENL +#define CONF_SLCD_LPENL (\ + (uint32_t)1 << 0 | \ + (uint32_t)1 << 1 | \ + (uint32_t)1 << 2 | \ + (uint32_t)1 << 3 | \ + (uint32_t)1 << 4 | \ + (uint32_t)1 << 5 | \ + (uint32_t)1 << 6 | \ + (uint32_t)1 << 7 | \ + (uint32_t)1 << 11 | \ + (uint32_t)1 << 12 | \ + (uint32_t)1 << 13 | \ + (uint32_t)1 << 14 | \ + (uint32_t)1 << 21 | \ + (uint32_t)1 << 22 | \ + (uint32_t)1 << 23 | \ + (uint32_t)1 << 24 | \ + (uint32_t)1 << 25 | \ + (uint32_t)1 << 28 | \ + (uint32_t)1 << 29 | \ + (uint32_t)1 << 30 | \ + (uint32_t)1 << 31 | 0) +#endif // CONF_SLCD_LPENL + +#ifndef CONF_SLCD_LPENH +#define CONF_SLCD_LPENH (\ + (uint32_t)1 << (32 - 32) | \ + (uint32_t)1 << (33 - 32) | \ + (uint32_t)1 << (34 - 32) | \ + (uint32_t)1 << (35 - 32) | \ + (uint32_t)1 << (42 - 32) | \ + (uint32_t)1 << (43 - 32) | 0) +#endif // CONF_SLCD_LPENH + +// <<< end of configuration section >>> + +#endif // HPL_SLCD_CONFIG_H diff --git a/watch-library/shared/config/hpl_systick_config.h b/watch-library/shared/config/hpl_systick_config.h new file mode 100644 index 00000000..a7f2f362 --- /dev/null +++ b/watch-library/shared/config/hpl_systick_config.h @@ -0,0 +1,18 @@ +/* Auto-generated config file hpl_systick_config.h */ +#ifndef HPL_SYSTICK_CONFIG_H +#define HPL_SYSTICK_CONFIG_H + +// <<< Use Configuration Wizard in Context Menu >>> + +// <h> Advanced settings +// <q> SysTick exception request +// <i> Indicates whether the generation of SysTick exception is enabled or not +// <id> systick_arch_tickint +#ifndef CONF_SYSTICK_TICKINT +#define CONF_SYSTICK_TICKINT 0 +#endif +// </h> + +// <<< end of configuration section >>> + +#endif // HPL_SYSTICK_CONFIG_H diff --git a/watch-library/shared/config/hpl_trng_config.h b/watch-library/shared/config/hpl_trng_config.h new file mode 100755 index 00000000..ba901498 --- /dev/null +++ b/watch-library/shared/config/hpl_trng_config.h @@ -0,0 +1,27 @@ +/* Auto-generated config file hpl_trng_config.h */ +#ifndef HPL_TRNG_CONFIG_H +#define HPL_TRNG_CONFIG_H + +// <<< Use Configuration Wizard in Context Menu >>> + +// <h> Advanced configurations + +// <q> Run In Standby +// <i> Indicates whether the TRNG works in standby mode +// <id> trng_runstdby +#ifndef CONF_TRNG_RUNSTDBY +#define CONF_TRNG_RUNSTDBY 0 +#endif + +// <q> Data Ready Event Output Enable +// <i> Indicates whether the TRNG generates event on Data Ready +// <id> trng_datardyeo +#ifndef CONF_TRNG_DATARDYEO +#define CONF_TRNG_DATARDYEO 0 +#endif + +// </h> + +// <<< end of configuration section >>> + +#endif // HPL_TRNG_CONFIG_H diff --git a/watch-library/shared/config/nv_storage_config.h b/watch-library/shared/config/nv_storage_config.h new file mode 100755 index 00000000..4888d1bd --- /dev/null +++ b/watch-library/shared/config/nv_storage_config.h @@ -0,0 +1,51 @@ +/* Auto-generated config file nv_storage_config.h */ +#ifndef NV_STORAGE_CONFIG_H +#define NV_STORAGE_CONFIG_H + +// <<< Use Configuration Wizard in Context Menu >>> + +//<o> Storage start address <0x00000000-0xFFFFFFFF> +//<i> This defines the start address of device flash for storage. +//<i> The start address should be in device flash area. +//<i> The start address and (start address + Item Number * Sector size) cannot beyond device flash area. +//<id> conf_storage_memory_start +#ifndef CONF_STORAGE_MEMORY_START +#define CONF_STORAGE_MEMORY_START 0x10000 +#endif + +//<o> Item number <0-65535> +//<i> This defines the maximum number of elements stored in persistent storage +//<id> conf_max_item_number +#ifndef CONF_MAX_ITEM_NUMBER +#define CONF_MAX_ITEM_NUMBER 10 +#endif + +//<o> Sector size <0-65535> +//<i> This defines the size of one storage sector in bytes +//<id> conf_sector_size +#ifndef CONF_SECTOR_SIZE +#define CONF_SECTOR_SIZE 4096 +#endif + +/** + * Check If the Storage configuration out of the flash area. + */ +#ifdef FLASH_SIZE +#if (CONF_STORAGE_MEMORY_START + (SECTOR_AMOUNT * CONF_SECTOR_SIZE)) > FLASH_SIZE +#error Invalidate storage configuration, make sure the configuration with \ +the sector start address (CONF_STORAGE_MEMORY_START) and sector size (CONF_SECTOR_SIZE) \ +are located within the device flash size. +#endif +#endif + +#ifdef IFLASH_SIZE +#if (CONF_STORAGE_MEMORY_START + (SECTOR_AMOUNT * CONF_SECTOR_SIZE)) > IFLASH_SIZE +#error Invalidate storage configuration, make sure the configuration with \ +the sector start address (CONF_STORAGE_MEMORY_START) and sector size (CONF_SECTOR_SIZE) \ +are located within the device flash size. +#endif +#endif + +// <<< end of configuration section >>> + +#endif // NV_STORAGE_CONFIG_H diff --git a/watch-library/shared/config/peripheral_clk_config.h b/watch-library/shared/config/peripheral_clk_config.h new file mode 100644 index 00000000..523b036c --- /dev/null +++ b/watch-library/shared/config/peripheral_clk_config.h @@ -0,0 +1,266 @@ +/* Auto-generated config file peripheral_clk_config.h */ +#ifndef PERIPHERAL_CLK_CONFIG_H +#define PERIPHERAL_CLK_CONFIG_H + +// <<< Use Configuration Wizard in Context Menu >>> + +// <y> ADC Clock Source +// <id> adc_gclk_selection + +// <GCLK_PCHCTRL_GEN_GCLK0_Val"> Generic clock generator 0 + +// <GCLK_PCHCTRL_GEN_GCLK1_Val"> Generic clock generator 1 + +// <GCLK_PCHCTRL_GEN_GCLK2_Val"> Generic clock generator 2 + +// <GCLK_PCHCTRL_GEN_GCLK3_Val"> Generic clock generator 3 + +// <GCLK_PCHCTRL_GEN_GCLK4_Val"> Generic clock generator 4 + +// <i> Select the clock source for ADC. +#ifndef CONF_GCLK_ADC_SRC +#define CONF_GCLK_ADC_SRC GCLK_PCHCTRL_GEN_GCLK0_Val +#endif + +/** + * \def CONF_GCLK_ADC_FREQUENCY + * \brief ADC's Clock frequency + */ +#ifndef CONF_GCLK_ADC_FREQUENCY +#define CONF_GCLK_ADC_FREQUENCY 4000000 +#endif + +// <y> EIC Clock Source +// <id> eic_gclk_selection + +// <GCLK_PCHCTRL_GEN_GCLK0_Val"> Generic clock generator 0 + +// <GCLK_PCHCTRL_GEN_GCLK1_Val"> Generic clock generator 1 + +// <GCLK_PCHCTRL_GEN_GCLK2_Val"> Generic clock generator 2 + +// <GCLK_PCHCTRL_GEN_GCLK3_Val"> Generic clock generator 3 + +// <GCLK_PCHCTRL_GEN_GCLK4_Val"> Generic clock generator 4 + +// <i> Select the clock source for EIC. +#ifndef CONF_GCLK_EIC_SRC +#define CONF_GCLK_EIC_SRC GCLK_PCHCTRL_GEN_GCLK3_Val +#endif + +/** + * \def CONF_GCLK_EIC_FREQUENCY + * \brief EIC's Clock frequency + */ +#ifndef CONF_GCLK_EIC_FREQUENCY +#define CONF_GCLK_EIC_FREQUENCY 32768 +#endif + +/** + * \def CONF_CPU_FREQUENCY + * \brief CPU's Clock frequency + */ +#ifndef CONF_CPU_FREQUENCY +#define CONF_CPU_FREQUENCY 4000000 +#endif + +// <y> RTC Clock Source +// <id> rtc_clk_selection +// <RTC_CLOCK_SOURCE"> RTC source +// <i> Select the clock source for RTC. +#ifndef CONF_GCLK_RTC_SRC +#define CONF_GCLK_RTC_SRC RTC_CLOCK_SOURCE +#endif + +/** + * \def CONF_GCLK_RTC_FREQUENCY + * \brief RTC's Clock frequency + */ +#ifndef CONF_GCLK_RTC_FREQUENCY +#define CONF_GCLK_RTC_FREQUENCY 1024 +#endif + +// <y> Core Clock Source +// <id> core_gclk_selection + +// <GCLK_PCHCTRL_GEN_GCLK0_Val"> Generic clock generator 0 + +// <GCLK_PCHCTRL_GEN_GCLK1_Val"> Generic clock generator 1 + +// <GCLK_PCHCTRL_GEN_GCLK2_Val"> Generic clock generator 2 + +// <GCLK_PCHCTRL_GEN_GCLK3_Val"> Generic clock generator 3 + +// <GCLK_PCHCTRL_GEN_GCLK4_Val"> Generic clock generator 4 + +// <i> Select the clock source for CORE. +#ifndef CONF_GCLK_SERCOM1_CORE_SRC +#define CONF_GCLK_SERCOM1_CORE_SRC GCLK_PCHCTRL_GEN_GCLK0_Val +#endif + +// <y> Slow Clock Source +// <id> slow_gclk_selection + +// <GCLK_PCHCTRL_GEN_GCLK0_Val"> Generic clock generator 0 + +// <GCLK_PCHCTRL_GEN_GCLK1_Val"> Generic clock generator 1 + +// <GCLK_PCHCTRL_GEN_GCLK2_Val"> Generic clock generator 2 + +// <GCLK_PCHCTRL_GEN_GCLK3_Val"> Generic clock generator 3 + +// <GCLK_PCHCTRL_GEN_GCLK4_Val"> Generic clock generator 4 + +// <i> Select the slow clock source. +#ifndef CONF_GCLK_SERCOM1_SLOW_SRC +#define CONF_GCLK_SERCOM1_SLOW_SRC GCLK_PCHCTRL_GEN_GCLK3_Val +#endif + +/** + * \def CONF_GCLK_SERCOM1_CORE_FREQUENCY + * \brief SERCOM1's Core Clock frequency + */ +#ifndef CONF_GCLK_SERCOM1_CORE_FREQUENCY +#define CONF_GCLK_SERCOM1_CORE_FREQUENCY 4000000 +#endif + +/** + * \def CONF_GCLK_SERCOM1_SLOW_FREQUENCY + * \brief SERCOM1's Slow Clock frequency + */ +#ifndef CONF_GCLK_SERCOM1_SLOW_FREQUENCY +#define CONF_GCLK_SERCOM1_SLOW_FREQUENCY 32768 +#endif + +// <y> Core Clock Source +// <id> core_gclk_selection + +// <GCLK_PCHCTRL_GEN_GCLK0_Val"> Generic clock generator 0 + +// <GCLK_PCHCTRL_GEN_GCLK1_Val"> Generic clock generator 1 + +// <GCLK_PCHCTRL_GEN_GCLK2_Val"> Generic clock generator 2 + +// <GCLK_PCHCTRL_GEN_GCLK3_Val"> Generic clock generator 3 + +// <GCLK_PCHCTRL_GEN_GCLK4_Val"> Generic clock generator 4 + +// <i> Select the clock source for CORE. +#ifndef CONF_GCLK_SERCOM3_CORE_SRC +#define CONF_GCLK_SERCOM3_CORE_SRC GCLK_PCHCTRL_GEN_GCLK0_Val +#endif + +// <y> Slow Clock Source +// <id> slow_gclk_selection + +// <GCLK_PCHCTRL_GEN_GCLK0_Val"> Generic clock generator 0 + +// <GCLK_PCHCTRL_GEN_GCLK1_Val"> Generic clock generator 1 + +// <GCLK_PCHCTRL_GEN_GCLK2_Val"> Generic clock generator 2 + +// <GCLK_PCHCTRL_GEN_GCLK3_Val"> Generic clock generator 3 + +// <GCLK_PCHCTRL_GEN_GCLK4_Val"> Generic clock generator 4 + +// <i> Select the slow clock source. +#ifndef CONF_GCLK_SERCOM3_SLOW_SRC +#define CONF_GCLK_SERCOM3_SLOW_SRC GCLK_PCHCTRL_GEN_GCLK3_Val +#endif + +/** + * \def CONF_GCLK_SERCOM3_CORE_FREQUENCY + * \brief SERCOM3's Core Clock frequency + */ +#ifndef CONF_GCLK_SERCOM3_CORE_FREQUENCY +#define CONF_GCLK_SERCOM3_CORE_FREQUENCY 4000000 +#endif + +/** + * \def CONF_GCLK_SERCOM3_SLOW_FREQUENCY + * \brief SERCOM3's Slow Clock frequency + */ +#ifndef CONF_GCLK_SERCOM3_SLOW_FREQUENCY +#define CONF_GCLK_SERCOM3_SLOW_FREQUENCY 32768 +#endif + +// <y> TC Clock Source +// <id> tc_gclk_selection + +// <GCLK_PCHCTRL_GEN_GCLK0_Val"> Generic clock generator 0 + +// <GCLK_PCHCTRL_GEN_GCLK1_Val"> Generic clock generator 1 + +// <GCLK_PCHCTRL_GEN_GCLK2_Val"> Generic clock generator 2 + +// <GCLK_PCHCTRL_GEN_GCLK3_Val"> Generic clock generator 3 + +// <GCLK_PCHCTRL_GEN_GCLK4_Val"> Generic clock generator 4 + +// <i> Select the clock source for TC. +#ifndef CONF_GCLK_TC3_SRC +#define CONF_GCLK_TC3_SRC GCLK_PCHCTRL_GEN_GCLK3_Val +#endif + +/** + * \def CONF_GCLK_TC3_FREQUENCY + * \brief TC3's Clock frequency + */ +#ifndef CONF_GCLK_TC3_FREQUENCY +#define CONF_GCLK_TC3_FREQUENCY 32768 +#endif + +// <y> TCC Clock Source +// <id> tcc_gclk_selection + +// <GCLK_PCHCTRL_GEN_GCLK0_Val"> Generic clock generator 0 + +// <GCLK_PCHCTRL_GEN_GCLK1_Val"> Generic clock generator 1 + +// <GCLK_PCHCTRL_GEN_GCLK2_Val"> Generic clock generator 2 + +// <GCLK_PCHCTRL_GEN_GCLK3_Val"> Generic clock generator 3 + +// <GCLK_PCHCTRL_GEN_GCLK4_Val"> Generic clock generator 4 + +// <i> Select the clock source for TCC. +#ifndef CONF_GCLK_TCC0_SRC +#define CONF_GCLK_TCC0_SRC GCLK_PCHCTRL_GEN_GCLK0_Val +#endif + +/** + * \def CONF_GCLK_TCC0_FREQUENCY + * \brief TCC0's Clock frequency + */ +#ifndef CONF_GCLK_TCC0_FREQUENCY +#define CONF_GCLK_TCC0_FREQUENCY 16000000 +#endif + +#include <hpl_osc32kctrl_config.h> + +// <y> SLCD Clock Source +// <id> slcd_clk_selection +// <SLCD_CLOCK_SOURCE"> SLCD source +// <i> Select the clock source for SLCD. +#ifndef CONF_GCLK_SLCD_SRC +#define CONF_GCLK_SLCD_SRC SLCD_CLOCK_SOURCE +#endif + +/** + * \def CONF_GCLK_SLCD_FREQUENCY + * \brief SLCD's Clock frequency + */ +#ifndef CONF_GCLK_SLCD_FREQUENCY +#define CONF_GCLK_SLCD_FREQUENCY 32768 +#endif + +#ifndef SLCD_FRAME_FREQUENCY +#define SLCD_FRAME_FREQUENCY \ + (CONF_GCLK_SLCD_FREQUENCY \ + / (((CONF_SLCD_PRESC + 1) * 16) * (CONF_SLCD_CKDIV + 1) \ + * ((CONF_SLCD_COM_NUM == 4) ? 6 : ((CONF_SLCD_COM_NUM == 5) ? 8 : (CONF_SLCD_COM_NUM + 1))))) +#endif + +// <<< end of configuration section >>> + +#endif // PERIPHERAL_CLK_CONFIG_H |