From 52c5747d2e873d4946d211c548c03498b72c1fb5 Mon Sep 17 00:00:00 2001 From: Joey Castillo Date: Tue, 19 Oct 2021 10:14:24 -0400 Subject: getting the sensor watch dev board working --- boards/OSO-FEAL-A1-00/pins.h | 120 +++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 120 insertions(+) create mode 100644 boards/OSO-FEAL-A1-00/pins.h (limited to 'boards/OSO-FEAL-A1-00') diff --git a/boards/OSO-FEAL-A1-00/pins.h b/boards/OSO-FEAL-A1-00/pins.h new file mode 100644 index 00000000..47d925cc --- /dev/null +++ b/boards/OSO-FEAL-A1-00/pins.h @@ -0,0 +1,120 @@ +#ifndef PINS_H_INCLUDED +#define PINS_H_INCLUDED + +// Detects if we are on USB power. +#define VBUS_DET GPIO(GPIO_PORTA, 3) + +// Buttons +#define BTN_ALARM GPIO(GPIO_PORTA, 2) +#define WATCH_BTN_ALARM_EIC_CHANNEL 2 +#define BTN_LIGHT GPIO(GPIO_PORTB, 5) +#define WATCH_BTN_LIGHT_EIC_CHANNEL 5 +#define BTN_MODE GPIO(GPIO_PORTA, 7) +#define WATCH_BTN_MODE_EIC_CHANNEL 7 + +// Buzzer +#define BUZZER GPIO(GPIO_PORTA, 27) +#define WATCH_BUZZER_TCC_PINMUX PINMUX_PA27F_TCC0_WO5 +#define WATCH_BUZZER_TCC_CHANNEL 1 + +// LEDs +#define WATCH_INVERT_LED_POLARITY +#define RED GPIO(GPIO_PORTA, 4) +#define WATCH_RED_TCC_CHANNEL 0 +#define WATCH_RED_TCC_PINMUX PINMUX_PA04E_TCC0_WO0 + +#ifdef WATCH_SWAP_LED_PINS + #define GREEN GPIO(GPIO_PORTB, 22) + #define WATCH_GREEN_TCC_CHANNEL 2 + #define WATCH_GREEN_TCC_PINMUX PINMUX_PB22F_TCC0_WO2 +#else + #define GREEN GPIO(GPIO_PORTB, 23) + #define WATCH_GREEN_TCC_CHANNEL 3 + #define WATCH_GREEN_TCC_PINMUX PINMUX_PB23F_TCC0_WO3 +#endif + + +// Segment LCD +#define SLCD0 GPIO(GPIO_PORTB, 6) +#define SLCD1 GPIO(GPIO_PORTB, 7) +#define SLCD2 GPIO(GPIO_PORTB, 8) +#define SLCD3 GPIO(GPIO_PORTB, 9) +#define SLCD4 GPIO(GPIO_PORTA, 5) +#define SLCD5 GPIO(GPIO_PORTA, 6) +#define SLCD6 GPIO(GPIO_PORTA, 8) +#define SLCD7 GPIO(GPIO_PORTA, 9) +#define SLCD8 GPIO(GPIO_PORTA, 10) +#define SLCD9 GPIO(GPIO_PORTA, 11) +#define SLCD10 GPIO(GPIO_PORTB, 11) +#define SLCD11 GPIO(GPIO_PORTB, 12) +#define SLCD12 GPIO(GPIO_PORTB, 13) +#define SLCD13 GPIO(GPIO_PORTB, 14) +#define SLCD14 GPIO(GPIO_PORTB, 15) +#define SLCD15 GPIO(GPIO_PORTA, 14) +#define SLCD16 GPIO(GPIO_PORTA, 15) +#define SLCD17 GPIO(GPIO_PORTA, 16) +#define SLCD18 GPIO(GPIO_PORTA, 17) +#define SLCD19 GPIO(GPIO_PORTA, 18) +#define SLCD20 GPIO(GPIO_PORTA, 19) +#define SLCD21 GPIO(GPIO_PORTB, 16) +#define SLCD22 GPIO(GPIO_PORTB, 17) +#define SLCD23 GPIO(GPIO_PORTA, 20) +#define SLCD24 GPIO(GPIO_PORTA, 21) +#define SLCD25 GPIO(GPIO_PORTA, 22) +#define SLCD26 GPIO(GPIO_PORTA, 23) +// This board uses a slightly different pin mapping from the standard watch, and it's not enough to +// just declare the pins. We also have to set the LCD Pin Enable register with the SLCD pins we're +// using. These numbers are not port/pin numbers, but the "SLCD/LP[x]" numbers in the pinmux table. +// If not defined in pins.h, the LCD drover will fall back to the pin mapping in hpl_slcd_config.h. +// LPENL is for pins SLCD/LP[0..31]. +#define CONF_SLCD_LPENL (\ + (uint32_t)1 << 0 | \ + (uint32_t)1 << 1 | \ + (uint32_t)1 << 2 | \ + (uint32_t)1 << 3 | \ + (uint32_t)1 << 5 | \ + (uint32_t)1 << 6 | \ + (uint32_t)1 << 11 | \ + (uint32_t)1 << 12 | \ + (uint32_t)1 << 13 | \ + (uint32_t)1 << 14 | \ + (uint32_t)1 << 21 | \ + (uint32_t)1 << 22 | \ + (uint32_t)1 << 23 | \ + (uint32_t)1 << 24 | \ + (uint32_t)1 << 25 | \ + (uint32_t)1 << 30 | \ + (uint32_t)1 << 31 | 0) +// LPENH is for pins SLCD/LP[32..51], where bit 0 represents pin 32. +#define CONF_SLCD_LPENH (\ + (uint32_t)1 << (32 - 32) | \ + (uint32_t)1 << (33 - 32) | \ + (uint32_t)1 << (34 - 32) | \ + (uint32_t)1 << (35 - 32) | \ + (uint32_t)1 << (42 - 32) | \ + (uint32_t)1 << (43 - 32) | \ + (uint32_t)1 << (48 - 32) | \ + (uint32_t)1 << (49 - 32) | \ + (uint32_t)1 << (50 - 32) | \ + (uint32_t)1 << (51 - 32) | 0) + + +// 9-pin connector +#define A0 GPIO(GPIO_PORTB, 4) +#define WATCH_A0_EIC_CHANNEL 4 +#define A1 GPIO(GPIO_PORTB, 1) +#define WATCH_A1_EIC_CHANNEL 1 +#define A2 GPIO(GPIO_PORTB, 2) +#define WATCH_A2_EIC_CHANNEL 2 +#define A3 GPIO(GPIO_PORTB, 3) +#define WATCH_A3_EIC_CHANNEL 3 +#define A4 GPIO(GPIO_PORTB, 0) +#define WATCH_A4_EIC_CHANNEL 0 +#define SDA GPIO(GPIO_PORTB, 30) +#define SCL GPIO(GPIO_PORTB, 31) + +// aliases for as A3/A4; these were mentioned as D0/D1 in early documentation. +#define D0 GPIO(GPIO_PORTB, 3) +#define D1 GPIO(GPIO_PORTB, 0) + +#endif // PINS_H_INCLUDED -- cgit v1.2.3