1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
|
/*
* The MIT License (MIT)
*
* Copyright (c) 2020, Ha Thach (tinyusb.org)
*
* Permission is hereby granted, free of charge, to any person obtaining a copy
* of this software and associated documentation files (the "Software"), to deal
* in the Software without restriction, including without limitation the rights
* to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
* copies of the Software, and to permit persons to whom the Software is
* furnished to do so, subject to the following conditions:
*
* The above copyright notice and this permission notice shall be included in
* all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
* IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
* FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
* AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
* LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
* OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
* THE SOFTWARE.
*
* This file is part of the TinyUSB stack.
*/
#include "../../board.h"
#include "board.h"
#include "esp_rom_gpio.h"
#include "hal/gpio_ll.h"
#include "hal/usb_hal.h"
#include "soc/usb_periph.h"
#include "driver/periph_ctrl.h"
#include "driver/rmt.h"
#ifdef NEOPIXEL_PIN
#include "led_strip.h"
static led_strip_t *strip;
#endif
//--------------------------------------------------------------------+
// MACRO TYPEDEF CONSTANT ENUM DECLARATION
//--------------------------------------------------------------------+
static void configure_pins(usb_hal_context_t *usb);
// Initialize on-board peripherals : led, button, uart and USB
void board_init(void)
{
#ifdef NEOPIXEL_PIN
#ifdef NEOPIXEL_POWER_PIN
gpio_reset_pin(NEOPIXEL_POWER_PIN);
gpio_set_direction(NEOPIXEL_POWER_PIN, GPIO_MODE_OUTPUT);
gpio_set_level(NEOPIXEL_POWER_PIN, NEOPIXEL_POWER_STATE);
#endif
// WS2812 Neopixel driver with RMT peripheral
rmt_config_t config = RMT_DEFAULT_CONFIG_TX(NEOPIXEL_PIN, RMT_CHANNEL_0);
config.clk_div = 2; // set counter clock to 40MHz
rmt_config(&config);
rmt_driver_install(config.channel, 0, 0);
led_strip_config_t strip_config = LED_STRIP_DEFAULT_CONFIG(1, (led_strip_dev_t) config.channel);
strip = led_strip_new_rmt_ws2812(&strip_config);
strip->clear(strip, 100); // off led
#endif
// Button
gpio_pad_select_gpio(BUTTON_PIN);
gpio_set_direction(BUTTON_PIN, GPIO_MODE_INPUT);
gpio_set_pull_mode(BUTTON_PIN, BUTTON_STATE_ACTIVE ? GPIO_PULLDOWN_ONLY : GPIO_PULLUP_ONLY);
// USB Controller Hal init
periph_module_reset(PERIPH_USB_MODULE);
periph_module_enable(PERIPH_USB_MODULE);
usb_hal_context_t hal = {
.use_external_phy = false // use built-in PHY
};
usb_hal_init(&hal);
configure_pins(&hal);
}
static void configure_pins(usb_hal_context_t *usb)
{
/* usb_periph_iopins currently configures USB_OTG as USB Device.
* Introduce additional parameters in usb_hal_context_t when adding support
* for USB Host.
*/
for (const usb_iopin_dsc_t *iopin = usb_periph_iopins; iopin->pin != -1; ++iopin) {
if ((usb->use_external_phy) || (iopin->ext_phy_only == 0)) {
esp_rom_gpio_pad_select_gpio(iopin->pin);
if (iopin->is_output) {
esp_rom_gpio_connect_out_signal(iopin->pin, iopin->func, false, false);
} else {
esp_rom_gpio_connect_in_signal(iopin->pin, iopin->func, false);
if ((iopin->pin != GPIO_FUNC_IN_LOW) && (iopin->pin != GPIO_FUNC_IN_HIGH)) {
gpio_ll_input_enable(&GPIO, iopin->pin);
}
}
esp_rom_gpio_pad_unhold(iopin->pin);
}
}
if (!usb->use_external_phy) {
gpio_set_drive_capability(USBPHY_DM_NUM, GPIO_DRIVE_CAP_3);
gpio_set_drive_capability(USBPHY_DP_NUM, GPIO_DRIVE_CAP_3);
}
}
// Turn LED on or off
void board_led_write(bool state)
{
#ifdef NEOPIXEL_PIN
strip->set_pixel(strip, 0, (state ? 0x88 : 0x00), 0x00, 0x00);
strip->refresh(strip, 100);
#endif
}
// Get the current state of button
// a '1' means active (pressed), a '0' means inactive.
uint32_t board_button_read(void)
{
return gpio_get_level(BUTTON_PIN) == BUTTON_STATE_ACTIVE;
}
// Get characters from UART
int board_uart_read(uint8_t* buf, int len)
{
(void) buf; (void) len;
return 0;
}
// Send characters to UART
int board_uart_write(void const * buf, int len)
{
(void) buf; (void) len;
return 0;
}
|
