blob: e8514347e27827aba4acf481b27566398c22cd4e (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
|
DEPS_SUBMODULES += hw/mcu/nuvoton
CFLAGS += \
-flto \
-mthumb \
-mabi=aapcs-linux \
-mcpu=cortex-m4 \
-mfloat-abi=hard \
-mfpu=fpv4-sp-d16 \
-DCFG_TUSB_MCU=OPT_MCU_NUC505
# All source paths should be relative to the top level.
LD_FILE = hw/bsp/$(BOARD)/nuc505_flashtoram.ld
SRC_C += \
src/portable/nuvoton/nuc505/dcd_nuc505.c \
hw/mcu/nuvoton/nuc505/Device/Nuvoton/NUC505Series/Source/system_NUC505Series.c \
hw/mcu/nuvoton/nuc505/StdDriver/src/adc.c \
hw/mcu/nuvoton/nuc505/StdDriver/src/clk.c \
hw/mcu/nuvoton/nuc505/StdDriver/src/gpio.c \
hw/mcu/nuvoton/nuc505/StdDriver/src/i2c.c \
hw/mcu/nuvoton/nuc505/StdDriver/src/i2s.c \
hw/mcu/nuvoton/nuc505/StdDriver/src/pwm.c \
hw/mcu/nuvoton/nuc505/StdDriver/src/rtc.c \
hw/mcu/nuvoton/nuc505/StdDriver/src/spi.c \
hw/mcu/nuvoton/nuc505/StdDriver/src/spim.c \
hw/mcu/nuvoton/nuc505/StdDriver/src/sys.c \
hw/mcu/nuvoton/nuc505/StdDriver/src/timer.c \
hw/mcu/nuvoton/nuc505/StdDriver/src/uart.c \
hw/mcu/nuvoton/nuc505/StdDriver/src/wdt.c \
hw/mcu/nuvoton/nuc505/StdDriver/src/wwdt.c
SRC_S += \
hw/mcu/nuvoton/nuc505/Device/Nuvoton/NUC505Series/Source/GCC/startup_NUC505Series.S
INC += \
$(TOP)/hw/mcu/nuvoton/nuc505/Device/Nuvoton/NUC505Series/Include \
$(TOP)/hw/mcu/nuvoton/nuc505/StdDriver/inc \
$(TOP)/hw/mcu/nuvoton/nuc505/CMSIS/Include
# For freeRTOS port source
FREERTOS_PORT = ARM_CM4F
# For flash-jlink target
JLINK_DEVICE = NUC505YO13Y
# Note
# To be able to program the SPI flash, it need to boot with ICP mode "1011".
# However, in ICP mode, opencod cannot establish connection to the mcu.
# Therefore, there is no easy command line flash for NUC505
# It is probably better to just use Nuvoton NuMicro ICP programming on windows to program the board
# - 1111 "SPI" (run from internal flash)
# - 1110 "USB" (mass storage emulator that accepts a .bin file)
# - 0111 "ICE-SPI" (allow external debugger access, but may not be programmable)
# - 1011 ICP mode (programmable via NuMicro ICP programming tool)
# Flash using Nuvoton's openocd fork at https://github.com/OpenNuvoton/OpenOCD-Nuvoton
# Please compile and install it from github source
flash: $(BUILD)/$(PROJECT).elf
openocd -f interface/nulink.cfg -f target/numicroM4.cfg -c "program $< reset exit"
|
